LinkIt Smart 7688 boot

LinkIt Smart 7688 boot

[04000D09][04000D07]
DDR Calibration DQS reg = 00008788


U-Boot 1.1.3 (Sep 10 2015 - 05:56:31)

Board: Ralink APSoC DRAM:  128 MB
relocate_code Pointer at: 87f68000
flash manufacture id: c2, device id 20 19
find flash: MX25L25635E
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 1024 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: SPI Flash
Date:Sep 10 2015  Time:05:56:31
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =128 Mbytes
RESET MT7628 PHY!!!!!!
GPIOMODE --> 50054404

GPIOMODE2 --> 5540551

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
 0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
   Image Name:   MIPS OpenWrt Linux-3.18.21
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1118491 Bytes =  1.1 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 128

Starting kernel ...

[    0.000000] Linux version 3.18.21 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r47269) ) #5 Fri Nov 20 12:43:14 CET 2015
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[    0.000000] MIPS: machine is MediaTek LinkIt Smart 7688
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS2,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=0005614a
[    0.000000] Readback ErrCtl register=0005614a
[    0.000000] Memory: 126332K/131072K available (2703K kernel code, 129K rwdata, 344K rodata, 144K init, 190K bss, 4740K reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] intc: using register map from devicetree
[    0.000000] CPU Clock: 580MHz
[    0.000000] clocksource_of_init: no matching clocksources found
[    0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.060000] pid_max: default: 32768 minimum: 301
[    0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.080000] pinctrl core: initialized pinctrl subsystem
[    0.090000] NET: Registered protocol family 16
[    0.110000] mt7621_gpio 10000600.gpio: registering 32 gpios
[    0.120000] mt7621_gpio 10000600.gpio: registering 32 gpios
[    0.130000] mt7621_gpio 10000600.gpio: registering 32 gpios
[    0.140000] Switched to clocksource MIPS
[    0.150000] NET: Registered protocol family 2
[    0.150000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.170000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.180000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.190000] TCP: reno registered
[    0.200000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.210000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.220000] NET: Registered protocol family 1
[    0.230000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.260000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.280000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.300000] msgmni has been set to 246
[    0.310000] io scheduler noop registered
[    0.320000] io scheduler deadline registered (default)
[    0.330000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.350000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
[    0.360000] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A
[    0.380000] console [ttyS2] disabled
[    0.390000] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 30, base_baud = 2500000) is a 16550A
[    0.410000] console [ttyS2] enabled
[    0.410000] console [ttyS2] enabled
[    0.420000] bootconsole [early0] disabled
[    0.420000] bootconsole [early0] disabled
[    0.440000] spi-mt7621 10000b00.spi: sys_freq: 193333333
[    0.450000] m25p80 spi32766.0: mx25l25635e (32768 Kbytes)
[    0.470000] m25p80 spi32766.0: using chunked io
[    0.470000] 4 ofpart partitions found on MTD device spi32766.0
[    0.490000] Creating 4 MTD partitions on "spi32766.0":
[    0.500000] 0x000000000000-0x000000030000 : "u-boot"
[    0.510000] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.520000] 0x000000040000-0x000000050000 : "factory"
[    0.530000] 0x000000050000-0x000002000000 : "firmware"
[    0.600000] 2 uimage-fw partitions found on MTD device firmware
[    0.610000] 0x000000050000-0x00000016115b : "kernel"
[    0.630000] 0x00000016115b-0x000002000000 : "rootfs"
[    0.640000] mtd: device 5 (rootfs) set to be root filesystem
[    0.650000] 1 squashfs-split partitions found on MTD device rootfs
[    0.660000] 0x000001500000-0x000002000000 : "rootfs_data"
[    0.680000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
[    0.700000] mt7621_wdt 10000120.watchdog: Initialized
[    0.710000] TCP: cubic registered
[    0.720000] NET: Registered protocol family 17
[    0.730000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.750000] Bridge firewalling registered
[    0.760000] 8021q: 802.1Q VLAN Support v1.8
[    0.770000] mtk-linkit bootstrap: Version  : LINKITS7688
[    0.780000] mtk-linkit bootstrap: Revision : REV3
[    0.790000] mtk-linkit bootstrap: setting up bootstrap latch
[    0.810000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    0.820000] Freeing unused kernel memory: 144K (8031c000 - 80340000)
[    2.120000] init: Console is alive
[    2.130000] init: - watchdog -
[    4.150000] usbcore: registered new interface driver usbfs
[    4.160000] usbcore: registered new interface driver hub
[    4.170000] usbcore: registered new device driver usb
[    4.190000] exFAT: Version 1.2.9
[    4.200000] SCSI subsystem initialized
[    4.220000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.230000] ehci-platform: EHCI generic platform driver
[    4.440000] phy phy-usbphy.0: remote usb device wakeup disabled
[    4.450000] phy phy-usbphy.0: UTMI 16bit 30MHz
[    4.460000] ehci-platform 101c0000.ehci: EHCI Host Controller
[    4.470000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    4.490000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    4.520000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    4.530000] hub 1-0:1.0: USB hub found
[    4.540000] hub 1-0:1.0: 1 port detected
[    4.550000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.560000] ohci-platform: OHCI generic platform driver
[    4.570000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[    4.580000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    4.600000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    4.670000] hub 2-0:1.0: USB hub found
[    4.680000] hub 2-0:1.0: 1 port detected
[    4.690000] platform gpio-leds: Driver leds-gpio requests probe deferral
[    4.710000] MTK MSDC device init.
[    4.760000] mtk-sd: MediaTek MT6575 MSDC Driver
[    4.770000] sdhci: Secure Digital Host Controller Interface driver
[    4.780000] sdhci: Copyright(c) Pierre Ossman
[    4.790000] platform gpio-leds: Driver leds-gpio requests probe deferral
[    4.800000] sdhci-pltfm: SDHCI platform and OF driver helper
[    4.820000] usbcore: registered new interface driver usb-storage
[    5.180000] init: - preinit -
[    6.220000] rt305x-esw 10110000.esw: link changed 0x00
[    6.420000] random: mktemp urandom read with 9 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.670000] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[    9.700000] procd: - early -
[    9.710000] procd: - watchdog -
[   10.550000] procd: - ubus -
[   11.570000] procd: - init -
Please press Enter to activate this console.
[   13.390000] NET: Registered protocol family 10
[   13.480000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.500000] i2c /dev entries driver
[   14.140000] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
[   14.160000] <-- RTMPAllocAdapterBlock, Status=0
[   14.170000] mtk_gpio_wifi gpio-wifi: registering 1 gpio
[   14.220000] i2c-ralink 10000900.i2c: loaded
[   14.240000] Linux video capture interface: v2.00
[   14.470000] Enable Ralink GDMA Controller Module
[   14.480000] GDMA IP Version=3
[   14.520000] ******* mt76xx_pcm_init *******
[   14.530000] *******Enter codec_wm8960_i2c_probe********
[   14.540000] soc-audio soc-audio: ASoC: machine MTK APSoC I2S should use snd_soc_register_card()
[   14.560000] wm8960 0-001a: No platform data supplied
[   15.070000] soc-audio soc-audio: wm8960-hifi <-> mt76xx-i2s mapping ok
[   15.100000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.120000] nf_conntrack version 0.5.0 (1976 buckets, 7904 max)
[   15.190000] usbcore: registered new interface driver uvcvideo
[   15.200000] USB Video Class driver (1.1.1)
[   15.230000] xt_time: kernel timezone is -0000
[   15.250000] PPP generic driver version 2.4.2
[   15.260000] NET: Registered protocol family 24
[   24.190000] device eth0 entered promiscuous mode
[   24.220000] br-lan: port 1(eth0) entered forwarding state
[   24.230000] br-lan: port 1(eth0) entered forwarding state
[   25.060000] efuse_probe: efuse = 10000012
[   25.070000] net ra0: Direct firmware load for mt7628.eeprom failed with error -2
[   25.080000] net ra0: Falling back to user helper
[   25.860000] tssi_0_target_pwr_g_band = 26
[   25.870000] tssi_1_target_pwr_g_band = 35
[   26.230000] br-lan: port 1(eth0) entered forwarding state
[   32.580000] <==== rt28xx_init, Status=0
[   33.590000] device ra0 entered promiscuous mode
[   33.600000] br-lan: port 2(ra0) entered forwarding state
[   33.610000] br-lan: port 2(ra0) entered forwarding state
[   34.030000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   34.050000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   34.060000] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   35.610000] br-lan: port 2(ra0) entered forwarding state



BusyBox v1.23.2 (2015-11-18 16:34:33 CET) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 CHAOS CALMER (15.05+linkit, r47501)
 -----------------------------------------------------
  * 1 1/2 oz Gin            Shake with a glassful
  * 1/4 oz Triple Sec       of broken ice and pour
  * 3/4 oz Lime Juice       unstrained into a goblet.
  * 1 1/2 oz Orange Juice
  * 1 tsp. Grenadine Syrup
 -----------------------------------------------------
root@mylinkit:/#