chrismeyersfsu

#!/usr/bin/perl
my $dev = "/sys/class/leds/led0/brightness";
my $OFF = "1";
my $ON = "0";

my ($ip) = `ifconfig`=~/ddr:(.*?) /;
#print $ip;

# Strip out the .'s
$ip =~ s/\.//g;

chrismeyersfsu

/* Blink LED example */

#include <msp430g2553.h>

/** Delay function. **/
delay(unsigned int d) {
  int i;
  for (i = 0; i<d; i++) {
    nop();
  }

chrismeyersfsu

#include "msp430g2553.h" // make sure you change the header to suit your particular device.
 
// Connect the servo SIGNAL wire to P1.2 through a 1K resistor.
 
#define MCU_CLOCK           1100000
#define PWM_FREQUENCY       46      // In Hertz, ideally 50Hz.
 
#define SERVO_STEPS         180     // Maximum amount of steps in degrees (180 is common)
#define SERVO_MIN           700     // The minimum duty cycle for this servo
#define SERVO_MAX           3000    // The maximum duty cycle

chrismeyersfsu

#define ANALOG_IN 0

void setup() {
  Serial.begin(9600); 
  //Serial.begin(115200); 
}

void loop() {
  int val = analogRead(ANALOG_IN);                                              
  Serial.write( 0xff );                                                         

chrismeyersfsu

// The Arduino code.                                                            
                                                                                
#define ANALOG_IN 0                                                             
int outPin=13;                                                                  
int outPinState = LOW;                                                          
int count = 1;                                                                  
int every = 10000;                                                              
                                                                                
void setup() {                                                                  
  //Serial.begin(9600);                                                         

chrismeyersfsu

  /*
 * Oscilloscope
 * Gives a visual rendering of analog pin 0 in realtime.
 * 
 * This project is part of Accrochages
 * See http://accrochages.drone.ws
 * 
 * (c) 2008 Sofian Audry ([email protected])
 *
 * This program is free software: you can redistribute it and/or modify

chrismeyersfsu

// Written by Nick Gammon
// February 2011
/**
 * Send arbitrary number of bits at whatever clock rate (tested at 500 KHZ and 500 HZ).
 * This script will capture the SPI bytes, when a '\n' is recieved it will then output
 * the captured byte stream via the serial.
 */

#include <SPI.h>

chrismeyersfsu

/*
 * SPI testing utility (using spidev driver)
 *
 * Copyright (c) 2007  MontaVista Software, Inc.
 * Copyright (c) 2007  Anton Vorontsov <[email protected]>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License.
 *

chrismeyersfsu

//******************************************************************************
//   MSP430G2xx3 Demo - USCI_A0, SPI 3-Wire Slave Data Echo
//
//   Description: SPI slave talks to SPI master using 3-wire mode. Data received
//   from master is echoed back.  USCI RX ISR is used to handle communication,
//   CPU normally in LPM4.  Prior to initial data exchange, master pulses
//   slaves RST for complete reset.
//   ACLK = n/a, MCLK = SMCLK = DCO ~1.2MHz
//
//   Use with SPI Master Incremented Data code example.  If the slave is in

chrismeyersfsu

npm --proxy http://198906:[email protected]:6050 install cordova -dd
npm info it worked if it ends with ok
npm verb cli [ '/usr/bin/node',
npm verb cli   '/usr/bin/npm',
npm verb cli   '--proxy',
npm verb cli   'http://198906:[email protected]:6050',
npm verb cli   'install',
npm verb cli   'cordova',
npm verb cli   '-dd' ]
npm info using [email protected]