gresan-gits

#include <ESP8266WiFi.h>
#include <FirebaseArduino.h>
#include <Ultrasonic.h>



#define LED     D0        // Led in NodeMCU at pin GPIO16 (D0).
// Set these to run example.
#define FIREBASE_HOST "garagecardetector.firebaseio.com"
#define FIREBASE_AUTH "TuJmJEc1YJRAOtEEiS1qYxYE2KiqRDaWNkGxyLhm"//change with your Database secrets

gresan-gits

 #include <main.h>
 #include <output.c>
 int8 in;
   
   void main  ()
   {
      output_float (pin_D7) ;
      //Example blinking LED program
      while (true)
      {

gresan-gits

#include <18F4520.h>
#FUSES NOWDT                    //No Watch Dog Timer
#FUSES WDT128                   //Watch Dog Timer uses 1:128 Postscale
#FUSES HS                       //High speed Osc (> 4mhz FOR PCM/PCH) (>10mhz for PCD)
#FUSES NOBROWNOUT               //No brownout reset
#FUSES NOLVP                    //No low voltage prgming, B3(PIC16) or B5(PIC18) used FOR I/O
#FUSES NOXINST                  //Extended set extension and Indexed Addressing mode disabled (Legacy mode)
#use delay(clock=12000000)

#use rs232(FORCE_SW,baud=4800,parity=N,xmit=PIN_B3,rcv=PIN_B4,bits=8,stream=UART_MEM,errors)

gresan-gits

#include <main.h>
#use rs232(UART1,baud=9600,parity=N,stream=UART,errors)

INT16 value, value2;

float vol;
void test(){
float a=5;
float b=1024;
float v=(float)a/b;

gresan-gits

#include <main.h>
#define LCD_ENABLE_PIN  PIN_B0                       
#define LCD_RS_PIN PIN_B1 
#define LCD_RW_PIN PIN_B2
#define LCD_DATA4 PIN_B4
#define LCD_DATA5 PIN_B5
#define LCD_DATA6 PIN_B6
#define LCD_DATA7 PIN_B7
#include <lcd.c>

gresan-gits

#include <ext.h>
#define LED_BAO PIN_D0
#define LED_NGAT PIN_D1
#INT_EXT //chi thi khai bao ngat(Chuong trinh se thuc hien ham ngay sau chi thi)
void  ngatngoai0_isr(VOID) //ham thuch hien khi co ngat
{
   fprintf (DEBUG_PORT, "\r\nBat dau thuc hien ham trong ngat");
   output_toggle (LED_NGAT);
   for (INT i = 0; i < 10; i++)
   {

gresan-gits

#include "main.h"
#define LED PIN_C0
#int_TIMER0
void  Ngat_TIMER0(void)
{
fprintf(PORT1,"Ngat timer 0\r\n");

}
#int_TIMER1
void  Ngat_TIMER1(void)

gresan-gits

#include <main.h>
/*
Cach tinh gia tri dutu thong qua set value
8bit value = period+1*duty_cycle
16bit value= 4*(period+1)*duty_cycle
*/

void main()
{
   setup_timer_2(T2_DIV_BY_4,124,1);      //100 us overflow, 100 us interrupt//Khoi tao timer 2 tao tan so pwm(10k)

gresan-gits

   /*** FILEHEADER ****************************************************************
 *
 *    FILENAME:    ds1820.h
 *    DATE:        25.02.2005
 *    AUTHOR:      Christian Stadler
 *
 *    DESCRIPTION: Driver for DS1820 1-Wire Temperature sensor (Dallas)
 *
 ******************************************************************************/

gresan-gits

#include <16F877A.h>
#device ADC=10
#FUSES NOWDT                    //No Watch Dog Timer
#FUSES NOBROWNOUT               //No brownout reset
#FUSES NOLVP                    //No low voltage prgming, B3(PIC16) or B5(PIC18) used FOR I/O
#use delay(crystal=12MHz)
#define LED PIN_C1
#define DELAY 10
#define RC PIN_E0
#define LCD_ENABLE_PIN PIN_D2