nophead

import serial

probe_z = 45
x_range = [-40, 40]
y_range = [-30, 60]
step = 2

def do_command(port,s):                     # send command and look for ok reply
    while True:
        port.write(s)

nophead

set style data lines
set pm3d implicit
set hidden3d
set grid
set contour base
set cntrparam levels auto 20
set xlabel "X"
set ylabel "Y"
set zlabel "mW"
set palette negative

nophead

set style data lines
set pm3d implicit
set hidden3d
set grid
set cntrparam levels auto 20
set xlabel "X"
set ylabel "Y"
set zlabel "mW"
set palette negative
set pm3d border

nophead

2014-10-23 16:58:02,141 - SERIAL - DEBUG - Enabling serial logging
2014-10-23 16:58:09,247 - SERIAL - DEBUG - Changing monitoring state from 'Operational' to 'Closed'
2014-10-23 16:58:13,303 - SERIAL - DEBUG - Connection closed, closing down monitor
2014-10-23 16:58:16,878 - SERIAL - DEBUG - Changing monitoring state from 'Offline' to 'Opening serial port'
2014-10-23 16:58:16,883 - SERIAL - DEBUG - Connecting to: /dev/ttyAMA0
2014-10-23 16:58:16,922 - SERIAL - DEBUG - Connected to: Serial<id=0x1ad8fb0, open=True>(port='/dev/ttyAMA0', baudrate=115200, bytesize=8, parity='N', stopbits=1, timeout=20.0, xonxoff=False, rtscts=False, dsrdtr=False), starting monitor
2014-10-23 16:58:16,926 - SERIAL - DEBUG - Changing monitoring state from 'Opening serial port' to 'Connecting'
2014-10-23 16:58:36,974 - SERIAL - DEBUG - Send: M105
2014-10-23 16:58:37,000 - SERIAL - DEBUG - Recv: ok T:21.5 /0.0 B:21.1 /0.0 @:0%
2014-10-23 16:58:37,005 - SERIAL - DEBUG - Changing monitoring state from 'Connecting' to 'Operational'

nophead

Send: M105
Recv: ok T:17.2 /0.0 B:17.6 /0.0 T0:17.2 /0.0 @:0.00 B@:0.00
Send: M20
Recv: Begin file list
Recv: SQUARE.GCO
Recv: E3DFAN~1.GCO
Recv: E3DUST~1.GCO
Recv: S_GEAR~1.GCO
Recv: ATXSHORT.GCO
Recv: DMOTORX2.G

nophead

//
// Elektor 500ppm LCR meter PCB PCB screen
//
$fa = 6;
$fs = 0.5;

thickness = 0.75;
pcb_clearance = 1.5;
pcb_width = 79;
pcb_length = 100;

nophead

paths = [ // a house
    [[-50, 0], [-50, 80], [0, 120], [50, 80], [50, 0], [8, 0], [8, 30], [-8, 30], [-8, 0],[-50, 0]],
    [[-40, 50], [-40, 70], [-20, 70], [-20, 50], [-40, 50]],
    [[ 20, 10], [ 20, 30], [ 40, 30], [ 40, 10], [ 20, 10]],
    [[ 20, 50], [ 20, 70], [ 40, 70], [ 40, 50], [ 20, 50]],
    [[-40, 10], [-40, 30], [-20, 30], [-20, 10], [-40, 10]],
];

home = [-150, 150]; // where to start from

nophead

//
// GNU GPL v2
// nop.head@gmail.com
// hydraraptor.blogspot.com
//
// Adapts ESP12 module to 0.1" grid.
//
eps = 1/128;            // small fudge factor to stop CSG barfing on coincident faces.
layer_height = 0.25;    // slicer layer height
extrusion_width = 0.5;  // slicer extrusion width

nophead

layer_height = 0.25;    // slicer layer height
extrusion_width = 0.5;  // slicer extrusion width
nozzle = 0.45;          // extruder nozzle aperture
squeezed_wall = extrusion_width - layer_height / 2 + nozzle / 2 + extrusion_width / 2;

wall = 2 * extrusion_width;
w = 20;
h = 10;
base = 1;
difference() {

nophead

void hspi_slave_begin() {
    pinMode(SCK, SPECIAL);                  // Both inputs in slave mode
    pinMode(MOSI, SPECIAL);
    SPI1C = 0;                              // SPI_CTRL_REG MSB first, single bit data mode.
    SPI1S = SPISE | SPISBE | SPISCD | 0x3E0;// SPI_SLAVE_REG, set slave mode, WR/RD BUF enable, CMD define, enable interrupts
    SPI1U = SPIUSSE;                        // SPI_USER_REG.  SPI_CK_I_EDGE
    SPI1CLK = 0;                            // SPI_CLOCK_REG
    SPI1U1 = 7 << SPILADDR;                 // SPI_USER1_REG, set address length to 8 bits
    SPI1U2 = 7 << SPILCOMMAND;              // SPI_USER2_REG, set command length to 8 bits
    SPI1S1 = (length * 8 - 1) << SPIS1LBUF; // SPI_SLAVE1_REG, SPI_SLV_BUF_BITLEN = 12 bytes