| /* | |
| * myalloc - a simplified reimplementation of glibc's malloc | |
| * | |
| * This allocator aims to follow in the spirit of the glibc implementation, | |
| * but with simplicity as the main design goal, instead of efficiency or | |
| * scalability. It uses a single free list instead of grouping blocks | |
| * into buckets, and is not at all thread safe. | |
| * | |
| * Some assumptions made: | |
| * - 2's complement, little endian, 8 bits per byte |
| # put this file in /etc/systemd/system/ as root | |
| # below paths assume solr installed in /opt/solr, SOLR_PID_DIR is /data | |
| # and that all configuration exists in /etc/default/solr.in.sh which is the case if previously installed as an init.d service | |
| # change port in pid file if differs | |
| # note that it is configured to auto restart solr if it fails (Restart=on-faliure) and that's the motivation indeed :) | |
| # to switch from systemv (init.d) to systemd, do the following after creating this file: | |
| # sudo systemctl daemon-reload | |
| # sudo service solr stop # if already running | |
| # sudo systemctl enable solr | |
| # systemctl start solr |
| module.exports = function atob(a) { | |
| return new Buffer(a, 'base64').toString('binary'); | |
| }; |
My ISP (Time Warner Cable) hands out IPv6 addresses with DHCPv6;
it will delegate a /56 if asked. So long as I keep refreshing the lease,
it won't renumber me. I have my cable modem set to bridge, and do all the
firewalling, NATing, etc., on a Debian box.
In what follows, eth0 is the internal interface.
The dhclient that ships with debian/ubuntu does not support asking for a prefix delegation, so I had to build one from sources.
| var supportsES6 = function() { | |
| try { | |
| new Function("(a = 0) => a"); | |
| return true; | |
| } | |
| catch (err) { | |
| return false; | |
| } | |
| }(); |
| # ~/.XCompose | |
| ### Based on the en_US.UTF locale. ### | |
| include "/usr/share/X11/locale/en_US.UTF-8/Compose" | |
| ### Populated with Kragen's additions. ### |
| --- a/drivers/net/wireless/ath/regd.c | |
| +++ b/drivers/net/wireless/ath/regd.c | |
| @@ -341,6 +341,10 @@ ath_reg_apply_beaconing_flags(struct wip | |
| struct ieee80211_channel *ch; | |
| unsigned int i; | |
| +#ifdef CONFIG_ATH_USER_REGD | |
| + return; | |
| +#endif | |
| + |
This tutorial will walk you through the steps needed to get root SSH
access on an Engenius EAP600 dual-band WiFi access point. SSH doesn't
come enabled out of the box on these things, so if you want to SSH into the
device (which is running an old version of OpenWRT), keep reading.
| ### | |
| ### | |
| ### UPDATE: For Win 11, I recommend using this tool in place of this script: | |
| ### https://christitus.com/windows-tool/ | |
| ### https://github.com/ChrisTitusTech/winutil | |
| ### https://www.youtube.com/watch?v=6UQZ5oQg8XA | |
| ### iwr -useb https://christitus.com/win | iex | |
| ### | |
| ### OR take a look at | |
| ### https://github.com/HotCakeX/Harden-Windows-Security |
| { | |
| "OP_DUP OP_HASH160 20 OP_EQUALVERIFY OP_CHECKSIG": 319721182, | |
| "OP_HASH160 20 OP_EQUAL": 10083919, | |
| "65 OP_CHECKSIG": 887766, | |
| "OP_RETURN": 288521, | |
| "OP_1 33 33 33 OP_3 OP_CHECKMULTISIG": 224438, | |
| "": 219175, | |
| "OP_1 33 33 OP_2 OP_CHECKMULTISIG": 206415, | |
| "33 OP_CHECKSIG": 101306, | |
| "OP_RETURN 40": 65287, |
