usart.c

/*
 * This file is part of the libopencm3 project.
 *
 * Copyright (C) 2009 Uwe Hermann <[email protected]>
 *
 * This library is free software: you can redistribute it and/or modify
 * it under the terms of the GNU Lesser General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This library is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU Lesser General Public License for more details.
 *
 * You should have received a copy of the GNU Lesser General Public License
 * along with this library.  If not, see <http://www.gnu.org/licenses/>.
 */

#include <libopencm3/stm32/f1/rcc.h>
#include <libopencm3/stm32/f1/gpio.h>
#include <libopencm3/stm32/usart.h>
#include "mystrlen.h"
#include "lcd.h"

void clock_setup(void);
void usart_setup(void);
void gpio_setup(void);

void clock_setup(void)
{
    rcc_clock_setup_in_hse_8mhz_out_24mhz();

    /* Enable GPIOC clock. */
    rcc_peripheral_enable_clock(&RCC_APB2ENR, RCC_APB2ENR_IOPCEN);

    /* Enable clocks for GPIO port A (for GPIO_USART1_TX) and USART1. */
    rcc_peripheral_enable_clock(&RCC_APB2ENR, RCC_APB2ENR_IOPAEN);
    rcc_peripheral_enable_clock(&RCC_APB2ENR, RCC_APB2ENR_USART1EN);
}

void usart_setup(void)
{
    /* Setup GPIO pin GPIO_USART1_TX/GPIO9 on GPIO port A for transmit. */
    gpio_set_mode(GPIOA, GPIO_MODE_OUTPUT_50_MHZ,
            GPIO_CNF_OUTPUT_ALTFN_PUSHPULL, GPIO_USART1_TX);

    /* Setup UART parameters. */
    // usart_set_baudrate(USART1, 38400);
    /* TODO usart_set_baudrate() doesn't support 24MHz clock (yet). */
    /* This is the equivalent: */
    USART_BRR(USART1) = 0x9c4;

    usart_set_databits(USART1, 8);
    usart_set_stopbits(USART1, USART_STOPBITS_1);
    usart_set_mode(USART1, USART_MODE_TX);
    usart_set_parity(USART1, USART_PARITY_NONE);
    usart_set_flow_control(USART1, USART_FLOWCONTROL_NONE);

    /* Finally enable the USART. */
    usart_enable(USART1);
}

void gpio_setup(void)
{
    /* Set GPIO9 (in GPIO port C) to 'output push-pull'. [LED] */
    gpio_set_mode(GPIOC, GPIO_MODE_OUTPUT_2_MHZ,
            GPIO_CNF_OUTPUT_PUSHPULL, GPIO9);
}

int main(void)
{
    int i;
    char *message = "Hello World!";

    clock_setup();
    gpio_setup();
    usart_setup();

    /* Blink the LED (PC9) on the board with every transmitted byte. */
    while (1) {
        gpio_toggle(GPIOC, GPIO9);	/* LED on/off */
        clearlcd();
        printlcd(message);
        for (i = 0; i < 800000; i++)	/* Wait a bit. */
            __asm__("NOP");
    }

    return 0;
}