-
-
Save CodeAsm/679da6101215bdeb6a93f718f794c910 to your computer and use it in GitHub Desktop.
ubee DDW3611 bootlog
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2017.03.17 21:30:14 =~=~=~=~=~=~=~=~=~=~=~= | |
| BCM338031 TP0 | |
| 1 | |
| Sync:1 | |
| 346890 | |
| MemSize: 64 M | |
| BootLoader Version: 10.1.2 Release Gnu spiboot reduced DDR drive | |
| Build Date: Dec 23 2009 | |
| Build Time: 15:43:35 | |
| SPI flash ID 0xc22017, size 8MB, block size 64KB, write buffer 256, busy bit 1 | |
| Signature/PID: a623 | |
| Image 1 Program Header: | |
| Signature: a623 | |
| Control: 0005 | |
| Major Rev: 0003 | |
| Minor Rev: 0000 | |
| Build Time: 2014/10/1 06:48:25 Z | |
| File Length: 3629577 bytes | |
| Load Address: 80004000 | |
| Filename: ecram_sto.bin | |
| HCS: c7fd | |
| CRC: 7957ca46 | |
| Found image 1 at offset 20000 | |
| Image 2 Program Header: | |
| Signature: a623 | |
| Control: 0005 | |
| Major Rev: 0003 | |
| Minor Rev: 0000 | |
| Build Time: 2015/3/9 08:23:39 Z | |
| File Length: 3629299 bytes | |
| Load Address: 80004000 | |
| Filename: ecram_sto.bin | |
| HCS: 18aa | |
| CRC: 364190e3 | |
| Found image 2 at offset 400000 | |
| Enter '1', '2', or 'p' within 2 seconds or take default... | |
| . . | |
| Performing CRC on Image 2... | |
| CRC time = 57361368 | |
| Detected LZMA compressed image... decompressing... | |
| Target Address: 0x80004000 | |
| decompressSpace is 0x4000000 | |
| Elapsed time 1152136237 | |
| Decompressed length: 18941436 | |
| Executing Image 2... | |
| eCos - hal_diag_init | |
| Init device '/dev/BrcmTelnetIoDriver' | |
| Init device '/dev/ttydiag' | |
| Init tty channel: 81214070 | |
| Init device '/dev/tty0' | |
| Init tty channel: 81214090 | |
| Init device '/dev/haldiag' | |
| HAL/diag SERIAL init | |
| Init device '/dev/ser0' | |
| BCM 33XX SERIAL init - dev: b4e00200.2 | |
| Set output buffer - buf: 0x812f4cc8 len: 4096 | |
| Set input buffer - buf: 0x812f5cc8 len: 4096 | |
| BCM 33XX SERIAL config | |
| Init device '/dev/ser1' | |
| BCM 33XX SERIAL init - dev: b4e00220.3 | |
| Set output buffer - buf: 0x812f6cc8 len: 4096 | |
| Set input buffer - buf: 0x812f7cc8 len: 4096 | |
| BCM 33XX SERIAL config | |
| LsSpiInit 3380 | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Configuring/Loading Flash driver... | |
| [00:00:00 01/01/1970] [tStartup] BcmSpiFlashDevice::DetectFlash: (SPI Flash Device Factory) WARNING - Detected SPI flash with JEDEC ID =0xc22017 | |
| [00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::SpiFlashPlaceRegions: (Flash Driver C API) WARNING - Permanent NonVol would fit in the boot block of this flash device, but I found existing NonVol in the following block; using this location instead... | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading BootloaderStore driver... | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading ProgramStore driver... | |
| ProgramStoreDeviceDriver::ProgramStoreDriverInit: INFO - Initializing... | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading NonVol driver... | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Storage drivers initialized successfully. | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Creating singletons for ProgramStore/BootloaderStore/NonVol devices... | |
| Detecting the next image number that we will store to by default... | |
| Bootloader indicates we are running image 2 | |
| By default, we will dload to image number 1! | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Device abstraction singletons created successfully. | |
| BcmHalIfNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! | |
| BcmHalIfNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! | |
| BcmHalIfNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! | |
| FoxRgNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! | |
| Reading Permanent settings from non-vol... | |
| Checksum for permanent settings: 0x9b7c5ed8 | |
| Setting downstream calibratiChipHalSelectPinMux: Setting pin mux sel 18, word 0, value 2 | |
| ChipHalSelectPinMux: Setting pin mux sel 21, word 0, value 1 | |
| ChipHalSelectPinMux: Setting pin mux sel 13, word 0, value 0 | |
| on signature to '' | |
| Setting downstream calibration signature Creating a new host MSG PROC DQM manager. Instance: 83f730c0, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| Initializing main MSG_PROC DQM interrupts. | |
| b8801000: 00000000 | |
| b8801004: 00000000 | |
| b8801008: 00000008 | |
| b880100c: 00000000 | |
| b8801010: 00000000 | |
| b8801014: 00000000 | |
| b8801018: 00000000 | |
| b880101c: 00000000 | |
| to '' | |
| Settings were read and Creating a new host FAP DQM manager. Instance: 83f7304c | |
| Initializing main FAP DQM interrupts. | |
| b8401000: 00000000 | |
| b8401004: 00000000 | |
| b8401008: 00000008 | |
| b840100c: 00000000 | |
| b8401010: 00000000 | |
| b8401014: 00000000 | |
| b8401018: 00000000 | |
| b840101c: 00000000 | |
| verified. | |
| ############################################# | |
| ### Copied settings from tuner 0 to tuner 1 | |
| ############################################# | |
| Reading Dynamic settings from non-vol... | |
| Checksum for dynamic settings: 0xf92cad67 | |
| Settings were read and verified. | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcFpmDriver::Init: Setting FPM Buffer size to: 2048 Base Address: 0x82f19da0 | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcFpmDriver::Init: fFpmLargestBufferSize: 2048 fFpmSizeShiftBits: 0xb | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcFpmDriver::Init: Pool index: 0 pool size: 2048 | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcFpmDriver::Init: Lookup table index: 0 pool size: 0 | |
| ------------------------------------ | |
| Free Pool Manager Configuration | |
| ------------------------------------ | |
| Buffer size in Bytes............... 2048 | |
| Number of Tokens................... 8192 | |
| Base Address of FPM Memory ........ 0xb2010200 | |
| Base Address of FPM Mem in DDR2.... 0x82f19da0 | |
| Total Configured FPM Memory Size... 16777216 | |
| Free Fifo Full..................... 0 | |
| Free Fifo Empty.................... 1 | |
| Alloc Fifo Full.................... 0 | |
| Alloc Fifo Empty................... 0 | |
| Number of tokens available......... 8192 | |
| Number of not valid token frees.... 0 | |
| Number of not valid token multi.... 0 | |
| Overflow Count..................... 0 | |
| Underflow Count.................... 0 | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcPacketAlloc::Init: Packet Alloc Header Buffer Start Addr: 0x82d61d80 Length: 0x1b8000 Max Buffer Size: 0xdc | |
| [00:00:00 01/01/1970] [Telnet Thread] BcmTelnetThread::ThreadMain: (Telnet Thread) Telnet server thread running... | |
| Creating SNMP agent cablemodem agent | |
| cablemodem agent disabling management. | |
| cablemodem agent defering traps. | |
| If you pressed the 's' key before this point, we will skip driver initialization... | |
| Creating TR-069 Thread... | |
| Creating DOCSIS Control Thread... | |
| vvv Interface creation and driver startup beginning vvv | |
| -> Begin Gfap HAL | |
| -> End GfInitalizing Gfap Hal.. | |
| ap HAL | |
| -> Begin DOCSIS CM WAN interface | |
| Creating HAL object for the DOCSIS CableModem interface | |
| Registering DOCSIS CableModem driver | |
| Initializing main DTP DQM interrupts. | |
| b4201000: 0000004c | |
| b4201004: 00000000 | |
| b4201008: 00000008 | |
| b420100c: 00000000 | |
| b4201010: 00000000 | |
| b4201014: 00000000 | |
| b4201018: 00000000 | |
| b420101c: 00000000 | |
| Creating a new host FAP DQM manager. Instance: 82cf0160 | |
| Creating a new host FAP DQM manager. Instance: 82cf005c | |
| Creating a new host UTP DQM manager. Instance: 82cebec8 | |
| Initializing main UTP DQM interrupts. | |
| b8001000: 0000000d | |
| b8001004: 00000000 | |
| b8001008: 00000008 | |
| b800100c: 00000000 | |
| b8001010: 00000001 | |
| b8001014: 00000000 | |
| b8001018: 00000000 | |
| b800101c: 00000000 | |
| LNA Detected = BCM3410 | |
| Initial Boost Status=0. Tilt Status=0 | |
| (Boost=Tilt=1)LNA Gain = 0x1f | |
| Final(Boost/Tilt=1/0) STATUS_READ2_REG=0x101f. | |
| ChipHalSelectPinMux: Setting pin mux sel 3, word 1, value 0 | |
| ChipHalSelectPinMux: Setting pin mux sel 1, word 1, value 0 | |
| Initializing all 8 downstreams - this takes a while. Patience, Grasshopper... | |
| 1 2 3 4 5 6 7 8 | |
| Fxtal is 48000000 | |
| Fclk_us_vco is 2088000000 | |
| Fclk_us_pll is 522000000 | |
| Fxtal is 48000000 | |
| Fclk_us_vco is 2088000000 | |
| Fclk_us_pll is 522000000 | |
| Fxtal is 48000000 | |
| Fclk_us_vco is 2088000000 | |
| Fclk_us_pll is 522000000 | |
| Fxtal is 48000000 | |
| Fclk_us_vco is 2088000000 | |
| Fclk_us_pll is 522000000 | |
| Fxtal is 48000000 | |
| Fclk_us_vco is 2088000000 | |
| Fclk_us_pll is 522000000 | |
| BcmMacInit: advMapRunAheadTimeMin = 3584 (0x00000e00) 10.24 MHz ticks, 350 usec | |
| Initializing DS Docsis 3.0 MAC | |
| Initializing CalcPhyPico | |
| BcmInitCalcPhyPico:Copying CalcPhy PicoCode rev 1.1.0 : 06/25/07 | |
| ...................................................................... | |
| Verifying CalcPhy PicoCode. | |
| ...................................................................... | |
| BcmInitCalcPhyPico:PicoCode verified. | |
| Creating a new host UTP DQM manager. Instance: 82ca7aa4 | |
| Creating a new host UTP DQM manager. Instance: 82ca79d0 | |
| [00:00:08 01/01/1970] [tStartup] BcmDocsisCmHalIf::Register: (DOCSIS CableModem HalIf) CM HAL reports h/w support for PHS, bitmask=0x3 | |
| [00:00:08 01/01/1970] [tStartup] BcmDocsisCmHalIf::Register: (DOCSIS CableModem HalIf) CM HAL reports h/w support for PHS, US size=64, DS size=256 bytes. | |
| -> End DOCSIS CM WAN interface | |
| -> Begin Ethernet LAN interfaces | |
| Creating HAL object for the Eth-Switch Lan(0) interface | |
| Registering Eth-Switch Lan(0) driver | |
| Creating a new host MSG PROC DQM manager. Instance: 82ca7150, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| Creating a new host MSG PROC DQM manager. Instance: 82ca707c, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| **** SETTING PHY DEFAULTS **** | |
| **** PEFORMING PHY CHECK **** | |
| >>>> Creating DQM bundle for DQM queue #: 3 | |
| Creating a new host MSG PROC DQM manager. Instance: 82ca6f08, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| >>>> Creating DQM bundle for DQM queue #: 0 | |
| Creating a new host MSG PROC DQM manager. Instance: 82ca6cfc, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| Enet Config GMAC UNIMAC Core: 1 Phy: 0 | |
| Ethernet Link Down! | |
| Number of Managed Switched Ports = 4 | |
| Creating HAL object for the Eth-Switch Lan(1) interface | |
| Registering Eth-Switch Lan(1) driver | |
| Creating HAL object for the Eth-Switch Lan(2) interface | |
| Registering Eth-Switch Lan(2) driver | |
| Creating HAL object for the Eth-Switch Lan(3) interface | |
| Registering Eth-Switch Lan(3) driver | |
| -> End Ethernet LAN interfaces | |
| -> Begin 802.11 WiFi LAN interface instance 0 | |
| Creating HAL object for (WiFi) interface #100 | |
| Registering (WiFi)(0)(0) Primary driver | |
| 802.11 country code in SROM query FAILED! | |
| 802.11 regulatory rev in SROM query FAILED! | |
| srom rev:8 | |
| WIFI INSTANCE 0 NIC DETECTED | |
| WiFi GPIO Configuration [WiFi Instance = 0] | |
| WiFi Device ID = 4353, Wifi Board Rev = 1202, WiFi Vendor ID = 14e4, WiFi WiFi Board ID = 4d8 | |
| Push Button: WiFi GPIO, Pin 0, Assert Level 0 | |
| WiFi Activity LED: WiFi GPIO, Pin 1, Assert Level 0 | |
| WPS 1 LED: WiFi GPIO, Pin 2, Assert Level 1 | |
| WPS 2 LED: WiFi GPIO, Pin 5, Assert Level 1 | |
| Vendor LED: UNDEFINED | |
| Error LED: UNDEFINED | |
| PCie Power On: UNDEFINED | |
| GPIO Extra Config: Reg Offset: 0x28, Mask Vale: 0x8000, Config Value: 0x8000 | |
| Creating HAL object for (WiFi) interface #101 | |
| Registering (WiFi)(0)(1) MBSS driver | |
| Creating HAL object for (WiFi) interface #102 | |
| Registering (WiFi)(0)(2) MBSS driver | |
| Creating HAL object for (WiFi) interface #103 | |
| Registering (WiFi)(0)(3) MBSS driver | |
| Creating HAL object for (WiFi) interface #104 | |
| Registering (WiFi)(0)(4) MBSS driver | |
| Creating HAL object for (WiFi) interface #105 | |
| Registering (WiFi)(0)(5) MBSS driver | |
| Creating HAL object for (WiFi) interface #106 | |
| Registering (WiFi)(0)(6) MBSS driver | |
| Creating HAL object for (WiFi) interface #107 | |
| Registering (WiFi)(0)(7) MBSS driver | |
| Creating HAL object for (WiFi) interface #108 | |
| Registering (WiFi)(0)(8) WDS driver | |
| Creating HAL object for (WiFi) interface #109 | |
| Registering (WiFi)(0)(9) WDS driver | |
| Creating HAL object for (WiFi) interface #110 | |
| Registering (WiFi)(0)(10) WDS driver | |
| Creating HAL object for (WiFi) interface #111 | |
| Registering (WiFi)(0)(11) WDS driver | |
| BcmWiFi80211NiHalIf::PrefetchMacAddresses | |
| MAC Address of SSID 0 : f0:7b:cb:5f:6f:e2 | |
| MAC Address of SSID 1 : f2:7b:cb:5f:6f:e3 | |
| MAC Address of SSID 2 : f2:7b:cb:5f:6f:e4 | |
| MAC Address of SSID 3 : f2:7b:cb:5f:6f:e5 | |
| MAC Address of SSID 4 : f2:7b:cb:5f:6f:e6 | |
| MAC Address of SSID 5 : f2:7b:cb:5f:6f:e7 | |
| MAC Address of SSID 6 : f2:7b:cb:5f:6f:e8 | |
| **** PEFORMING PHY CHECK **** | |
| MAC Address of SSID 7 : f2:7b:cb:5f:6f:e9 | |
| wl: Unsupported | |
| -> End 802.11 WiFi LAN interfaces. | |
| nas_main: Thread creation ok | |
| nas_main: Thread start ok | |
| BcmWpsPBCThread: Thread creation ok | |
| wpsPBCStart: Thread start ok | |
| -> Begin IP Stacwps_main: upnp I/F not up yet... | |
| k interfaces | |
| -> Starting BFC DHCP Client subsystem... | |
| -> Starting BFC DHCPv6 Client subsystem... | |
| Creating HAL object for IP Stack1 (MAC Addr=f8:2f:a8:bb:83:99) | |
| Registering IP Stack1 driver | |
| Tcpip NI: Init - RegisteredStackCount = 1 | |
| Creating HAL object for IP Stack2 (MAC Addr=00:d0:59:de:ad:02) | |
| Registering IP Stack2 driver | |
| Tcpip NI: Init - RegisteredStackCount = 2 | |
| Creating HAL object for IP Stack3 (MAC Addr=f8:2f:a8:bb:83:9a) | |
| Registering IP Stack3 driver | |
| Tcpip NI: Init - RegisteredStackCount = 3 | |
| Creating HAL object for IP Stack4 (MAC Addr=00:d0:59:de:ad:04) | |
| Registering IP Stack4 driver | |
| Tcpip NI: Init - RegisteredStackCount = 4 | |
| Creating HAL object for IP Stack5 (MAC Addr=f8:2f:a8:bb:83:9b) | |
| Registering IP Stack5 driver | |
| Tcpip NI: Init - RegisteredStackCount = 5 | |
| -> End IP Stack interfaces | |
| USB host subsytem intilialized | |
| Successfully mapped HCD interrupt 12 | |
| Registered BRCM USB HCD with USB Host subytem | |
| ^^^ Interface creation and driver startup complete ^^^ | |
| Forward Assist Manager Starting... | |
| Creating the eRouter Forwarder... | |
| Adding Eth-Switch Lan(0) HalIf to the eRouter Forwarder | |
| Adding Eth-Switch Lan(1) HalIf to the eRouter Forwarder | |
| Adding Eth-Switch Lan(2) HalIf to the eRouter Forwarder | |
| Adding Eth-Switch Lan(3) HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(0) Primary HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(1) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(2) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(3) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(4) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(5) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(6) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(7) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(8) WDS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(9) WDS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(10) WDS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(11) WDS HalIf to the eRouter Forwarder | |
| Adding IP Stack3 HalIf to the eRouter Forwarder | |
| Adding IP Stack4 HalIf to the eRouter Forwarder | |
| Adding IP Stack5 HalIf to the eRouter Forwarder | |
| Creating the DOCSIS Forwarder... | |
| Adding DOCSIS CableModem HalIf as the default interface to the DOCSIS Forwarder | |
| Adding IP Stack1 HalIf to the DOCSIS Forwarder | |
| Adding IP Stack2 HalIf to the DOCSIS Forwarder | |
| Adding WAN-Man Interface HalIf as the default interface to the eRouter Forwarder | |
| Adding Ethernet CPE Interface All HalIf to the DOCSIS Forwarder | |
| [00:00:10 01/01/1970] [tStartup] BcmEpsCmDocsisSystem::InstallMiniUsfs: (BFC System) Installing Mini-Usfs snoop | |
| Current IP address is default 0.0.0.0. | |
| Configuring IP stack 2: IP Address = 192.168.100.1 | |
| SES2WindowClosed! (unexpected) | |
| [00:00:11 01/01/1970] [tStartup] BcmEcosIpHalIf::AddIpv6LinkLocalAddress: (IP Stack2 HalIf) Configuring link-local IPv6 address fe80::2d0:59ff:fede:ad02/64 | |
| Creating Propane Control Thread... | |
| Propane version: 2.0.1 (28 Oct 2002) | |
| Instantiating CmSnmpAgent object. | |
| Starting SNMP subsystem | |
| Registering STP Filter Snoop with all interfaces. | |
| Registering DOCSIS MIB Filter Snoop with CPE and WAN interfaces. | |
| Creating SNMP agent CPE diag agent | |
| CPE diag agent disabling management. | |
| CPE diag agent defering traps. | |
| BcmSnmpThread starting thread operation. | |
| Initializing Net-SNMP transport for IPv4 | |
| Initializing Net-SNMP transport for IPv6 | |
| IPv6 - register netsnmp_brcmV6_ctor to get our brcm V6 UDP domain | |
| IPv6 init_bcmV2SessionAndTransport: Open a session and hook our callbacks | |
| ERROR! Can't add twcDeviceGroup to cableModemMibGroup, 1.3.6.1.4.1.1174.100 doesn't descend from 1.3.6.1.4.1.4684.2 | |
| [00:00:13 01/01/1970] [tStartup] BcmDocsisCmHalIf::RegisterSnmpObjects: (DOCSIS CableModem HalIf) Interface 10 additional registration w/ SNMP agent OK. | |
| [00:00:13 01/01/1970] [tStartup] BcmErouterPacketSwitchBridgingHalIf::RegisterSnmpObjects: (Ethernet CPE Interface All HalIf) Interface 39 additional registration w/ SNMP agent OK. | |
| Setting US cal singleton instance to 0 | |
| Register:: SKIPPPING index 13 | |
| Register:: SKIPPPING index 14 | |
| Register:: SKIPPPING index 15 | |
| Register:: SKIPPPING index 16 | |
| Register:: SKIPPPING index 17 | |
| Register:: SKIPPPING index 18 | |
| Register:: SKIPPPING index 19 | |
| BcmCommandTable::AddInstance: ERROR - Attempted to add duplicate instance 'FoxAgwThread' (0x82a663b8) to command table 'Message Log Settings Commands'. | |
| CmSnmpAgent installing views... | |
| CmSnmpAgent installing DOCSIS Default View entries... | |
| Vendor CM Agent w/ BRCM Factory Support setting V1/V2 view to unrestricted | |
| Vendor CM Agent w/ BRCM Factory Support installing engine ID... | |
| Vendor CM Agent w/ BRCM Factory Support installing context... | |
| NAT Session Manager: PSM start is @ 15810000 (3380) | |
| Creating a new host MSG PROC DQM manager. Instance: 82a25b70, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| InitializeNapDqmMessageChannel SUCCESS! | |
| hostNapHalIf: InitializeNapDqmMessageChannel SUCCESS! | |
| NatTrafficCounterPsmOffset SUCCESS! | |
| Counter PSM Offset is 17952 | |
| DMA4 replace PSM Offset is 5664 | |
| DMA6 replace PSM Offset is 14368 | |
| DMA checksum PSM Offset is 32 | |
| NatpFfeOffsets SUCCESS! | |
| FFE HASH4 0 Bin Offset is 57 | |
| FFE HASH6 0 Bin Offset is 607 | |
| FFE DMA4 REPLACE Offset is 217 | |
| FFE DMA6 REPLACE Offset is 767 | |
| SNMP startup complete. | |
| ************************************ | |
| *** Start up CPU load monitor module | |
| ************************************ | |
| [[00:00:15 01/01Creating a new host MSG PROC DQM manager. Instance: 82a0ccc4, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| Creating a new host MSG PROC DQM manager. Instance: 82a0cc08, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| wps_main: upnp I/F not up yet... | |
| /1970] [tStartup] BcmDocsisCmHalIf::AddSnoop: (DOCSIS CableModem HalIf) WARNING - VendorPacketSnoop: unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:15 01/01/1970] [tStartup] BcmDocsisCmHalIf::SortSnoops: (DOCSIS CableModem HalIf) WARNING - Unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:15 01/01/1970] [tStartup] BcmDocsisCmHalIf::AddSnoop: (DOCSIS CableModem HalIf) WARNING - VendorPacketSnoop: unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:15 01/01/1970] [tStartup] BcmDocsisCmHalIf::SortSnoops: (DOCSIS CableModem HalIf) WARNING - Unsafe modification of the Snoop lists after the interface is up! | |
| BcmCommandTable::AddInstance: ERROR - Attempted to add duplicate instance 'ND Thread for IP Stack1' (0x829fbd3c) to command table 'Message Log Settings Commands'. | |
| Current IP address is default 0.0.0.0. | |
| Configuring IP stack 5: IP Address = 192.168.0.1 | |
| 0V[0: 0:15 1/ 1/1970] [NAT Session Manager Thread] BcmNatSessionManagerThread::ThreadMain: (NAT Session Manager Thread) NAT Session Manager waiting for events... | |
| 00:00:15 01/01/1970] [FTP Lite Client Thread] FtpLiteClientThread::ThreadMain: (FTP Lite Client Thread) Broadcom FTP Lite Client thread starting... | |
| endor CM Event Log initializing with stored events. | |
| Event log initialization complete. | |
| [ERROR] key_from_blob: remaining bytes in key blob 167 BcmDhcpV6ServerThread::GetSingletonInstance: DhcpV6 Server Thread has not been initialized yet | |
| BcmDhcpV6ServerThread::GetSingletonInstance: DhcpV6 Server Thread has not been initialized yet | |
| BcmDhcpV6ServerThread::GetSingletonInstance: DhcpV6 Server Thread has not been initialized yet | |
| BcmDhcpV6ServerThread::GetSingletonInstance: DhcpV6 Server Thread has not been initialized yet | |
| BcmDhcpV6ServerThread::GetSingletonInstance: DhcpV6 Server Thread has not been initialized yet | |
| [00:00:16 01/01/1970] [tStartup] BcmeRouterDhcpv6IpHelper::CreateLease: Creating DHCP lease for client id = htype=1, value=f8:2f:a8:bb:83:9a | |
| Creating SNMP agent CH agent | |
| CH agent disabling management. | |
| CH agent defering traps. | |
| Instantiating eRouter SnmpAgent object. | |
| ERROR creating RadioHalif(1)!! | |
| CHSnmpAgent installing views... | |
| Vendor CH Agent w/ BRCM Factory Support setting V1/V2 view to unrestricted | |
| Vendor CH Agent w/ BRCM Factory Support installing engine ID... | |
| Vendor CH Agent w/ BRCM Factory Support installing context... | |
| Creating SNMP agent CH diag agent | |
| CH diag agent disabling management. | |
| CH diag agent defering traps. | |
| CH diag agent setting V1/V2 view to unrestricted | |
| CH diag agent enabling management. | |
| CH diag agent sending deferred traps... | |
| Done w/ deferred traps. | |
| CH diag agent installing engine ID... | |
| CH diag agent installing context... | |
| Stored lease with clientId: htype=0, value=00 23 12 fa fd a2 Ip address: 192.168.0.5 has been added as zombie! | |
| [00:00:19 01/01/1970] [tStartup] CableHomeDhcpServerIpServiceAppIf::HandleStoredDhcpServerLease: (CableHomeDhcpServerIpServiceAppIf) Updating database entry method to (4) for stored lease 192.168.0.5 | |
| [00:00:19 01/01/1970] [tStartup] CableHomeDhcpServerIpServiceAppIf::HandleStoredDhcpServerLease: (CableHomeDhcpServerIpServiceAppIf) Updating NonVol method to (4) for stored lease 192.168.0.5 | |
| [00:00:19 01/01/1970] [tStartup] CableHomeDhcpServerIpServiceAppIf::HandleStoredDhcpServerLease: (CableHomeDhcpServerIpServiceAppIf) Adding NAPT entry for LAN address = 192.168.0.5 | |
| [00:00:19 01/01/1970] [tStartup] CableHomeDhcpServerIpServiceAppIf::ConfigureDhcpStaticLeasedEntry: (CableHomeDhcpServerIpServiceAppIf) Configure Dhcp Static Leased Entry. | |
| Registering Qos2 Policy Table | |
| Registering Qos2 Traffic Class Table | |
| Registering Lan Addr Entry Table | |
| [00:00:19 01/01/1970] [tStartup] BcmRipClientThread::AuthEnable: (Rip Client Thread) Broadcom V2 RIP Client MD5 Authentication status = 1 | |
| [00:00:19 01/01/1970] [tStartup] BcmRipClientThread::Enable: (Rip Client Thread) Rip client configured on IpHalIf with 0.0.0.0 IP address - RIP disabled! | |
| [00:00:19 01/01/1970] [tStartup] BcmDocsisCmHalIf::AddSnoop: (DOCSIS CableModem HalIf) WARNING - RoutedSubnetCmSnoop: unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:20 01/01/1970] [tStartup] BcmDocsisCmHalIf::SortSnoops: (DOCSIS CableModem HalIf) WARNING - Unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:20 01/01/1970] [IkeThread] IkeThread::Initialize: (IkeThread) INFO - Initializing thread objects... | |
| [00:00:20 01/01/1970] [tStartup] IkeThread::BcmVpnNonVolSettings: (IkeThread) INFO - Setting up the singleton pointer. | |
| Creating BcmVpnCommandTable | |
| Dynamic DNS client DISABLED. | |
| BcmCommandTable::AddInstance: ERROR - Attempted to add duplicate instance 'NDThread on IP Stack3' (0x8281ec50) to command table 'Message Log Settings Commands'. | |
| [00:00:20 01/01/1970] [IkeThread] IkeThread::ThreadMain: (IkeThread) Entering... | |
| [00:00:20 01/01/1970] [IkeThread] IkeThread::ThreadMain: (IkeThread) Starting IPSEC/IKE initialization | |
| UPnP::upnp_device_attach:bcm4: attach WFADevice.xml | |
| Setting DHCPv6 server provisioning to (1) | |
| -- Detected (Eth-Switch Lan(0)) Mask: 0x1 as (primary) LAN interface | |
| -- Detected (Eth-Switch Lan(1)) Mask: 0x2 as (primary) LAN interface | |
| -- Detected (Eth-Switch Lan(2)) Mask: 0x4 as (primary) LAN interface | |
| -- Detected (Eth-Switch Lan(3)) Mask: 0x8 as (primary) LAN interface | |
| -- Detected ((WiFi)(0)(0) Primary) Mask: 0x10 as (primary) LAN interface | |
| -- Detected ((WiFi)(0)(1) MBSS) Mask: 0x20 as (non-primary) LAN interface | |
| -- Detected ((WiFi)(0)(2) MBSS) Mask: 0x40 as (non-primary) LAN interface | |
| -- Detected ((WiFi)(0)(3) MBSS) Mask: 0x80 as (non-primary) LAN interface | |
| -- Detected ((WiFi)(0)(4) MBSS) Mask: 0x100 as (non-primary) LAN interface | |
| -- Detected ((WiFi)(0)(5) MBSS) Mask: 0x200 as (non-primary) LAN interface | |
| -- Detected ((WiFi)(0)(6) MBSS) Mask: 0x400 as (non-primary) LAN interface | |
| -- Detected ((WiFi)(0)(7) MBSS) Mask: 0x800 as (non-primary) LAN interface | |
| BcmCommandTable::AddInstance: ERROR - Attempted to add duplicate instance 'NDT (Primary)' (0x8280e7dc) to command table 'Message Log Settings Commands'. | |
| BcmCommandTable::AddInstance: ERROR - Attempted to add duplicate instance 'NDT ((WiFi)(0)(1) MBSS) (0x20)' (0x8280b6d4) to command table 'Message Log Settings Commands'. | |
| BcmCommandTable::AddInstance: ERROR - Attempted to add duplicate instance 'NDT ((WiFi)(0)(2) MBSS) (0x40)' (0x828034c4) to command table 'Message Log Settings Commands'. | |
| BcmCommandTable::AddInstance: ERROR - Attempted to add duplicate instance 'NDT ((WiFi)(0)(3) MBSS) (0x80)' (0x82800348) to command table 'Message Log Settings Commands'. | |
| BcmCommandTable::AddInstance: ERROR - Attempted to add duplicate instance 'NDT ((WiFi)(0)(4) MBSS) (0x100)' (0x827fd1cc) to command table 'Message Log Settings Commands'. | |
| BcmCommandTable::AddInstance: ERROR - Attempted to add duplicate instance 'NDT ((WiFi)(0)(5) MBSS) (0x200)' (0x827f9fa0) to command table 'Message Log Settings Commands'. | |
| BcmCommandTable::AddInstance: ERROR - Attempted to add duplicate instance 'NDT ((WiFi)(0)(6) MBSS) (0x400)' (0x827f6e20) to command table 'Message Log Settings Commands'. | |
| BcmCommandTable::AddInstance: ERROR - Attempted to add duplicate instance 'NDT ((WiFi)(0)(7) MBSS) (0x800)' (0x827f3c98) to command table 'Message Log Settings Commands'. | |
| WARNING - Couldn't find group 1.3.6.1.4.1.4684.38.2.2.2.1.1.3 on Vendor CH Agent w/ BRCM Factory Support | |
| WARNING - Couldn't find group 1.3.6.1.4.1.4684.38.2.2.2.1.1.3 on Vendor CH Agent w/ BRCM Factory Support | |
| WARNING - Couldn't find group 1.3.6.1.4.1.4684.38.2.2.2.1.1.3 on CH diag agent | |
| [00:00:21 01/01/1970] [tStartup] BcmRgHttpServerThread::Enable: (HttpServerThread) Broadcom HttpServerThread running status = 1 | |
| ********************************************************** | |
| Running as a Residental Gateway Enabled device! | |
| ********************************************************** | |
| *********************************************** | |
| (DHCP) WAN IP Connection Configuration | |
| *********************************************** | |
| *********************************************** | |
| Primary LAN (NAT) | |
| *********************************************** | |
| [00:00:21 01/01/1970] [tStartup] CableHomeDhcpServerIpServiceAppIf::EnableDhcpServerProvisioning: (CableHomeDhcpServerIpServiceAppIf) Setting DHCP server provisioning to (1) | |
| [00:00:21 01/01/1970] [tStartup] BcmDocsisCmHalIf::AddSnoop: (DOCSIS CableModem HalIf) WARNING - AccessList Snoop: unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:21 01/01/1970] [tStartup] BcmDocsisCmHalIf::SortSnoops: (DOCSIS CableModem HalIf) WARNING - Unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:21 01/01/1970] [tStartup] BcmDocsisCmHalIf::AddSnoop: (DOCSIS CableModem HalIf) WARNING - AccessList Snoop: unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:21 01/01/1970] [tStartup] BcmDocsisCmHalIf::SortSnoops: (DOCSIS CableModem HalIf) WARNING - Unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:21 01/01/1970] [tStartup] BcmDocsisCmHalIf::AddSnoop: (DOCSIS CableModem HalIf) WARNING - SrcFix Snoop: unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:21 01/01/1970] [tStartup] BcmDocsisCmHalIf::SortSnoops: (DOCSIS CableModem HalIf) WARNING - Unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:21 01/01/1970] [tStartup] BcmDocsisCmHalIf::AddSnoop: (DOCSIS CableModem HalIf) WARNING - SrcFix Snoop: unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:21 01/01/1970] [tStartup] BcmDocsisCmHalIf::SortSnoops: (DOCSIS CableModem HalIf) WARNING - Unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:21 01/01/1970] [tStartup] FoxTplusThread::Enable: (Tplus Client Thread) Tplus enabled! | |
| StartFoxTplusClient: Starting TACACS Client Thread successfully!! | |
| [00:00:21 01/01/1970] [tStartup] BcmSled::GlobalEnable: (Singleton Instance) WARNING - eDOCSIS SLED is being disabled. | |
| Enabled HCD interrupt 12 | |
| Initializing TR-069 Client stack | |
| [[ | |
| Checking board manufacturing state... | |
| WARNING: Board NV manufacturing incomplete. | |
| Check the following settings: | |
| IP stack 2 MAC, IP stack 4 MAC, Default factory keys not changed | |
| U000:00:21 01/01/1970] [Tplus Client Thread] FoxTplusThread::ThreadMain: (Tplus Client Thread) Foxconn Tplus Client starting...waiting for events... | |
| sb Print Server - Bound to CM IP Address = [ 192.168.100.1 ] to listen for print requests. | |
| USB Print Server - Starting print server thread | |
| 0: 0:21 1/ 1/1970] [NDT (Primary)] NeighborDiscoveryThread::SendRouterAdvertisementPacket: (NDT (Primary)) ERROR - Link Local Address is not Configured. Can't send RA! | |
| Vendor CPE Agent w/ BRCM Factory Support setting V1/V2 view to unrestricted | |
| Removed USB | |
| Vendor CPE Agent w/ BRCM Factory Support enabling management. | |
| Vendor CPE Agent w/ BRCM Factory Support sending deferred traps... | |
| Done w/ deferred traps. | |
| Vendor CPE Agent w/ BRCM Factory Support installing engine ID... | |
| Vendor CPE Agent w/ BRCM Factory Support installing context... | |
| Vendor CPE Agent w/ BRCM Factory Support setting V1/V2 view to docsisCpeView | |
| ****************************************************** | |
| WAN DHCPv6 prefix not present yet! | |
| ****************************************************** | |
| ****************************************************** | |
| RA configured with (zero) router lifetime! | |
| ****************************************************** | |
| acsd_main: Thread creation ok | |
| acsd_main: Thread start ok | |
| [00:00:22 01/01/1970] [tStartup] CableHomeDhcpServerIpServiceAppIf::ArpServerLeasePool: (CableHomeDhcpServerIpServiceAppIf) Arping Dhcp Server Lease pool to populate Usfs table: (192.168.0.2) --> (192.168.0.254) | |
| +-----------------------------------------------------------------------+ | |
| | Portions of this product contain open source software and are subject | | |
| | to terms of the applicable license as specified in the release notes. | | |
| +-----------------------------------------------------------------------+ | |
| * | |
| * * | |
| * * | |
| * * | |
| * * | |
| * * | |
| * * | |
| * * | |
| * * | |
| * * | |
| * * | |
| * * | |
| * * | |
| * * | |
| * * | |
| * * | |
| * * * * | |
| * * * * * * *** | |
| * * * * * * * * ******************* | |
| * * * * * * | |
| * * | |
| Broadcom Corporation Reference Design | |
| +----------------------------------------------------------------------------+ | |
| | | |
| | _/_/ _/_/_/_/ _/_/ | |
| | | |
| | _/ _/ _/ _/ _/ Broadband | |
| | | |
| | _/ _/ _/ _/ | |
| | | |
| | _/_/ _/_/_/ _/ Foundation | |
| | | |
| | _/ _/ _/ _/ | |
| | | |
| | _/ _/ _/ _/ _/ Classes | |
| | | |
| | _/_/_/ _/ _/_/ | |
| | | |
| | | |
| | | |
| | Copyright (c) 1999 - 2013 Broadcom Corporation | |
| | | |
| | | |
| | | |
| | Revision: 5.5.8mp8 | |
| | | |
| | | |
| | | |
| | Features: BCM93380WRG Console TelnetConsole Nonvol Fat HeapManager SNMP | |
| | | |
| | Features: Networking USB2.0 IPv6 USB-Host (script bcm93380wrg_U10C045) | |
| | | |
| | Features: Switch53125 TR69 | |
| +----------------------------------------------------------------------------+ | |
| | | |
| | Standard Embedded Target Support for BFC | |
| | | |
| | | |
| | | |
| | Copyright (c) 2003-2013 Broadcom Corporation | |
| | | |
| | | |
| | | |
| | Revision: 3.0.1 | |
| | | |
| | | |
| | | |
| | Features: PID=0xa623 BID=0x0 Bootloader-Rev=10.1.2 | |
| | | |
| | Features: Bootloader-Compression-Support=0x11 MANUFACT_BITS=0xd | |
| | | |
| | Features: Bcm80211=Build Dec 11 2013 11:37:19 | |
| | | |
| | Features: App Ver 6.30.102.13.558.77 | |
| | | |
| | Features: Wl Ver 6.30.102.13.558.77 | |
| | | |
| | Features: IopLib-Rev=558.46.0 | |
| +----------------------------------------------------------------------------+ | |
| | | |
| | eCos BFC Application Layer | |
| | | |
| | | |
| | | |
| | Copyright (c) 1999 - 2013 Broadcom Corporation | |
| | | |
| | | |
| | | |
| | Revision: 3.0.2 | |
| | | |
| | | |
| | | |
| | Features: eCos Console Cmds, (no Idle Loop Profiler) | |
| +----------------------------------------------------------------------------+ | |
| | | |
| | _/_/ _/ _/ | |
| | | |
| | _/ _/ _/_/ _/_/ DOCSIS Cable Modem | |
| | | |
| | _/ _/ _/ _/ | |
| | | |
| | _/ _/ _/ | |
| | | |
| | _/ _/ _/ | |
| | | |
| | _/ _/ _/ _/ | |
| | | |
| | _/_/ _/ _/ | |
| | | |
| | | |
| | | |
| | Copyright (c) 1999 - 2013 Broadcom Corporation | |
| | | |
| | | |
| | | |
| | Revision: 5.5.8mp8 | |
| | | |
| | | |
| | | |
| | Features: AckCel(tm) DOCSIS 1.0/1.1/2.0/3.0 Propane(tm) CM SNMP w/Factory | |
| | | |
| | Features: MIB Support CM Vendor Extension eDOCSIS SLED D3.0 Drop | |
| | | |
| | Features: Classifiers FAP NA Production Time WarnerCustom UI | |
| +----------------------------------------------------------------------------+ | |
| | | |
| | Broadcom Data-Only CM Vendor Extension | |
| | | |
| | | |
| | | |
| | Copyright (c) 1999 - 2013 Broadcom Corporation | |
| | | |
| | | |
| | | |
| | Revision: 3.0.2 | |
| | | |
| | | |
| | | |
| | Features: DHCP Server HTTP Server OSS2-N-03025 Visualization LED | |
| | | |
| | Features: Controller Reset/Standby Switch Support | |
| +----------------------------------------------------------------------------+ | |
| | | |
| | _/_/_/ | |
| | | |
| | _/_/ _/ _/ eRouter Dual Stack | |
| | | |
| | _/ _/ _/ _/ | |
| | | |
| | _/_/_/_/ _/_/_/ | |
| | | |
| | _/ _/ _/ | |
| | | |
| | _/ _/ _/ | |
| | | |
| | _/_/_/ _/ _/ | |
| | | |
| | | |
| | | |
| | Copyright (c) 1999 - 2013 Broadcom Corporation | |
| | | |
| | | |
| | | |
| | Revision: 5.5.8mp8 | |
| | | |
| | | |
| | | |
| | Features: eRouter SNMP Customer Extension NATP | |
| +----------------------------------------------------------------------------+ | |
| | | |
| | Broadcom eRouter Customer Extension | |
| | | |
| | | |
| | | |
| | Copyright (c) 1999 - 2013 Broadcom Corporation | |
| | | |
| | | |
| | | |
| | Revision: 3.0.2 | |
| | | |
| | | |
| | | |
| | Features: () | |
| +----------------------------------------------------------------------------+ | |
| | | |
| | System Name: Ubee Wireless CableModem | |
| | | |
| | Build Date: Mar 9 2015 | |
| | | |
| | Build Time: 16:23:20 (+0800) | |
| | | |
| | Built By: borland | |
| | | |
| | Model Name: DDW3611 | |
| | | |
| | Firmware version: 8.6.5205 | |
| +----------------------------------------------------------------------------+ | |
| Running the system... | |
| Beginning Cable Modem operation... | |
| Beginning Parental Control operation... | |
| Beginning eRouter operation... | |
| [00:00:24 01/01/1970] [tStartup] BcmEcosIpHalIf::AddSnoop: (IP Stack5 HalIf) WARNING - IcmpIpStack Snoop: unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:24 01/01/1970] [tStartup] BcmEcosIpHalIf::SortSnoops: (IP Stack5 HalIf) WARNING - Unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:24 01/01/1970] [tStartup] BcmEcosIpHalIf::AddSnoop: (IP Stack5 HalIf) WARNING - IcmpIpStack Snoop: unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:24 01/01/1970] [tStartup] BcmEcosIpHalIf::SortSnoops: (IP Stack5 HalIf) WARNING - Unsafe modification of the Snoop lists after the interface is up! | |
| [[[00:00:24 01/01/1970] [Scan Downstream Thread] BcmGenericCmDownstreamScanThread::ThreadMain: (Scan Downstream Thread) Scanning for a Downstream Channel... | |
| [00:00:24 01/01/1970] [Scan Downstream Thread] BcmGenericCmDownstreamScanThread::ScanStarting: (Scan Downstream Thread) Scanning STD & HRC Annex B channel plan frequencies | |
| Resetting EnergyDetected to false. | |
| Forgetting energy frequency. | |
| Scanning (last happy) DS Channel at 345000000 Hz... | |
| 00: 0:24 1/ 1/1970] [Telnet Thread] BcmTelnetThread::CreateAndBindIp: (Telnet Thread) Telnet listening on 192.168.100.1 | |
| Type 'help' or '?' for a list of commands... | |
| CM> 00: 0:24 1/ 1/1970] [CableHomePingTool Thread] CableHomePingTool::ArpIpAddressRange: (CableHomePingTool Thread) ARP'ing of Ip Address Range (192.168.0.2) --> (192.168.0.254) | |
| ****************************************************** | |
| Performing DAD for LAN IPv6 Link Local | |
| ****************************************************** | |
| CM> Scanning DS Channel at 345000000 Hz...(from scan list) | |
| Scanning DS Channel at 297000000 Hz...(from scan list) | |
| DAD Success: LAN IPv6 Link-Local: fe80::fa2f:a8ff:febb:839b/64 | |
| [00:00:25 01/01/1970] [NDT (Primary)] BcmEcosIpHalIf::AddIpv6LinkLocalAddress: (IP Stack5 HalIf) Configuring link-local IPv6 address fe80::fa2f:a8ff:febb:839b/64 | |
| ****************************************************** | |
| Starting LAN IPv6 Provisioning! | |
| ****************************************************** | |
| ****************************************************** | |
| WAN DHCPv6 prefix not present yet! | |
| ****************************************************** | |
| ****************************************************** | |
| RA configured with (zero) router lifetime! | |
| ****************************************************** | |
| CM> Logging event: WiFi Interface [wl0] set to Channel 1 (Side-Band Channel:N/A) - Reason:INIT | |
| Scanning DS Channel at 291000000 Hz...(from scan list) | |
| Scanning DS Channel at 285000000 Hz...(from scan list) | |
| CM> Scanning DS Channel at 321000000 Hz...(from scan list) | |
| Scanning DS Channel at 339000000 Hz...(from scan list) | |
| Scanning DS Channel at 333000000 Hz...(from scan list) | |
| Scanning DS Channel at 327000000 Hz...(from scan list) | |
| Scanning DS Channel at 315000000 Hz...(from scan list) | |
| Scanning DS Channel at 279000000 Hz...(from scan list) | |
| Scanning DS Channel at 309000000 Hz...(from scan list) | |
| Scanning DS Channel at 303000000 Hz...(from scan list) | |
| Scanning DS Channel at 369000000 Hz...(from scan list) | |
| Scanning DS Channel at 363000000 Hz...(from scan list) | |
| Scanning DS Channel at 357000000 Hz...(from scan list) | |
| Scanning DS Channel at 351000000 Hz...(from scan list) | |
| Scanning (pattern) DS Channel at 999000000 Hz... | |
| Initializing energy frequency to 999000000 Hz. | |
| Scanning (pattern) DS Channel at 993000000 Hz... | |
| Scanning (pattern) DS Channel at 987000000 Hz... | |
| Scanning (pattern) DS Channel at 981000000 Hz... | |
| Scanning (pattern) DS Channel at 975000000 Hz... | |
| Scanning (pattern) DS Channel at 969000000 Hz... | |
| Scanning (pattern) DS Channel at 963000000 Hz... | |
| Scanning (pattern) DS Channel at 957000000 Hz... | |
| Scanning (pattern) DS Channel at 951000000 Hz... | |
| Scanning (pattern) DS Channel at 945000000 Hz... | |
| Scanning (pattern) DS Channel at 939000000 Hz... | |
| Scanning (pattern) DS Channel at 933000000 Hz... | |
| Scanning (pattern) DS Channel at 927000000 Hz... | |
| Scanning (pattern) DS Channel at 921000000 Hz... | |
| Scanning (pattern) DS Channel at 915000000 Hz... | |
| Scanning (pattern) DS Channel at 909000000 Hz... | |
| Scanning (pattern) DS Channel at 903000000 Hz... | |
| Scanning (pattern) DS Channel at 897000000 Hz... | |
| Scanning (pattern) DS Channel at 891000000 Hz... | |
| Scanning (pattern) DS Channel at 885000000 Hz... | |
| Scanning (pattern) DS Channel at 879000000 Hz... | |
| Scanning (pattern) DS Channel at 873000000 Hz... | |
| Scanning (pattern) DS Channel at 867000000 Hz... | |
| Scanning (pattern) DS Channel at 861000000 Hz... | |
| Scanning (pattern) DS Channel at 855000000 Hz... | |
| Scanning (pattern) DS Channel at 849000000 Hz... | |
| Scanning (pattern) DS Channel at 843000000 Hz... | |
| Scanning (pattern) DS Channel at 837000000 Hz... | |
| Scanning (pattern) DS Channel at 831000000 Hz... | |
| Scanning (pattern) DS Channel at 825000000 Hz... | |
| Scanning (pattern) DS Channel at 819000000 Hz... | |
| Scanning (pattern) DS Channel at 813000000 Hz... | |
| Scanning DS Channel at 345000000 Hz...(from scan list) | |
| Scanning DS Channel at 297000000 Hz...(from scan list) | |
| Scanning DS Channel at 291000000 Hz...(from scan list) | |
| Scanning DS Channel at 285000000 Hz...(from scan list) | |
| Scanning DS Channel at 321000000 Hz...(from scan list) | |
| Scanning DS Channel at 339000000 Hz...(from scan list) | |
| Scanning DS Channel at 333000000 Hz...(from scan list) | |
| Scanning DS Channel at 327000000 Hz...(from scan list) | |
| Scanning DS Channel at 315000000 Hz...(from scan list) | |
| Scanning DS Channel at 279000000 Hz...(from scan list) | |
| Scanning DS Channel at 309000000 Hz...(from scan list) | |
| Scanning DS Channel at 303000000 Hz...(from scan list) | |
| Scanning DS Channel at 369000000 Hz...(from scan list) | |
| Scanning DS Channel at 363000000 Hz...(from scan list) | |
| Scanning DS Channel at 357000000 Hz...(from scan list) | |
| Scanning DS Channel at 351000000 Hz...(from scan list) | |
| Scanning (pattern) DS Channel at 807000000 Hz... | |
| Scanning (pattern) DS Channel at 801000000 Hz... | |
| Scanning (pattern) DS Channel at 795000000 Hz... | |
| Scanning (pattern) DS Channel at 789000000 Hz... | |
| Scanning (pattern) DS Channel at 783000000 Hz... | |
| Scanning (pattern) DS Channel at 777000000 Hz... | |
| Scanning (pattern) DS Channel at 771000000 Hz... | |
| Scanning (pattern) DS Channel at 765000000 Hz... | |
| Scanning (pattern) DS Channel at 759000000 Hz... | |
| Scanning (pattern) DS Channel at 753000000 Hz... | |
| Scanning (pattern) DS Channel at 747000000 Hz... | |
| Scanning (pattern) DS Channel at 741000000 Hz... | |
| Scanning (pattern) DS Channel at 735000000 Hz... | |
| Scanning (pattern) DS Channel at 729000000 Hz... | |
| Scanning (pattern) DS Channel at 723000000 Hz... | |
| Scanning (pattern) DS Channel at 717000000 Hz... | |
| Scanning (pattern) DS Channel at 711000000 Hz... | |
| Scanning (pattern) DS Channel at 705000000 Hz... | |
| Scanning (pattern) DS Channel at 699000000 Hz... | |
| Scanning (pattern) DS Channel at 693000000 Hz... | |
| Scanning (pattern) DS Channel at 687000000 Hz... | |
| Scanning (pattern) DS Channel at 681000000 Hz... | |
| Scanning (pattern) DS Channel at 675000000 Hz... | |
| Scanning (pattern) DS Channel at 669000000 Hz... | |
| Scanning (pattern) DS Channel at 663000000 Hz... | |
| Scanning (pattern) DS Channel at 657000000 Hz... | |
| Scanning (pattern) DS Channel at 651000000 Hz... | |
| Scanning (pattern) DS Channel at 645000000 Hz... | |
| Scanning (pattern) DS Channel at 639000000 Hz... | |
| Scanning (pattern) DS Channel at 633000000 Hz... | |
| Scanning (pattern) DS Channel at 627000000 Hz... | |
| Scanning (pattern) DS Channel at 621000000 Hz... | |
| Scanning DS Channel at 345000000 Hz...(from scan list) | |
| Scanning DS Channel at 297000000 Hz...(from scan list) | |
| BCM338031 TP0 | |
| 1 | |
| Sync:1 | |
| 346890 | |
| MemSize: 64 M | |
| BootLoader Version: 10.1.2 Release Gnu spiboot reduced DDR drive | |
| Build Date: Dec 23 2009 | |
| Build Time: 15:43:35 | |
| SPI flash ID 0xc22017, size 8MB, block size 64KB, write buffer 256, busy bit 1 | |
| Signature/PID: a623 | |
| Image 1 Program Header: | |
| Signature: a623 | |
| Control: 0005 | |
| Major Rev: 0003 | |
| Minor Rev: 0000 | |
| Build Time: 2014/10/1 06:48:25 Z | |
| File Length: 3629577 bytes | |
| Load Address: 80004000 | |
| Filename: ecram_sto.bin | |
| HCS: c7fd | |
| CRC: 7957ca46 | |
| Found image 1 at offset 20000 | |
| Image 2 Program Header: | |
| Signature: a623 | |
| Control: 0005 | |
| Major Rev: 0003 | |
| Minor Rev: 0000 | |
| Build Time: 2015/3/9 08:23:39 Z | |
| File Length: 3629299 bytes | |
| Load Address: 80004000 | |
| Filename: ecram_sto.bin | |
| HCS: 18aa | |
| CRC: 364190e3 | |
| Found image 2 at offset 400000 | |
| Enter '1', '2', or 'p' within 2 seconds or take default... | |
| . . | |
| Performing CRC on Image 2... | |
| CRC time = 57361392 | |
| Detected LZMA compressed image... decompressing... | |
| Target Address: 0x80004000 | |
| decompressSpace is 0x4000000 | |
| Elapsed time 1152135662 | |
| Decompressed length: 18941436 | |
| Executing Image 2... | |
| eCos - hal_diag_init | |
| Init device '/dev/BrcmTelnetIoDriver' | |
| Init device '/dev/ttydiag' | |
| Init tty channel: 81214070 | |
| Init device '/dev/tty0' | |
| Init tty channel: 81214090 | |
| Init device '/dev/haldiag' | |
| HAL/diag SERIAL init | |
| Init device '/dev/ser0' | |
| BCM 33XX SERIAL init - dev: b4e00200.2 | |
| Set output buffer - buf: 0x812f4cc8 len: 4096 | |
| Set input buffer - buf: 0x812f5cc8 len: 4096 | |
| BCM 33XX SERIAL config | |
| Init device '/dev/ser1' | |
| BCM 33XX SERIAL init - dev: b4e00220.3 | |
| Set output buffer - buf: 0x812f6cc8 len: 4096 | |
| Set input buffer - buf: 0x812f7cc8 len: 4096 | |
| BCM 33XX SERIAL config | |
| LsSpiInit 3380 | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Configuring/Loading Flash driver... | |
| [00:00:00 01/01/1970] [tStartup] BcmSpiFlashDevice::DetectFlash: (SPI Flash Device Factory) WARNING - Detected SPI flash with JEDEC ID =0xc22017 | |
| [00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::SpiFlashPlaceRegions: (Flash Driver C API) WARNING - Permanent NonVol would fit in the boot block of this flash device, but I found existing NonVol in the following block; using this location instead... | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading BootloaderStore driver... | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading ProgramStore driver... | |
| ProgramStoreDeviceDriver::ProgramStoreDriverInit: INFO - Initializing... | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading NonVol driver... | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Storage drivers initialized successfully. | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Creating singletons for ProgramStore/BootloaderStore/NonVol devices... | |
| Detecting the next image number that we will store to by default... | |
| Bootloader indicates we are running image 2 | |
| By default, we will dload to image number 1! | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Device abstraction singletons created successfully. | |
| BcmHalIfNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! | |
| BcmHalIfNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! | |
| BcmHalIfNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! | |
| FoxRgNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! | |
| Reading Permanent settings from non-vol... | |
| Checksum for permanent settings: 0x9b7c5ed8 | |
| Setting downstream calibratiChipHalSelectPinMux: Setting pin mux sel 18, word 0, value 2 | |
| ChipHalSelectPinMux: Setting pin mux sel 21, word 0, value 1 | |
| ChipHalSelectPinMux: Setting pin mux sel 13, word 0, value 0 | |
| on signature to '' | |
| Setting downstream calibration signature Creating a new host MSG PROC DQM manager. Instance: 83f730c0, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| Initializing main MSG_PROC DQM interrupts. | |
| b8801000: 00000000 | |
| b8801004: 00000000 | |
| b8801008: 00000008 | |
| b880100c: 00000000 | |
| b8801010: 00000000 | |
| b8801014: 00000000 | |
| b8801018: 00000000 | |
| b880101c: 00000000 | |
| to '' | |
| Settings were read and Creating a new host FAP DQM manager. Instance: 83f7304c | |
| Initializing main FAP DQM interrupts. | |
| b8401000: 00000000 | |
| b8401004: 00000000 | |
| b8401008: 00000008 | |
| b840100c: 00000000 | |
| b8401010: 00000000 | |
| b8401014: 00000000 | |
| b8401018: 00000000 | |
| b840101c: 00000000 | |
| verified. | |
| ############################################# | |
| ### Copied settings from tuner 0 to tuner 1 | |
| ############################################# | |
| Reading Dynamic settings from non-vol... | |
| Checksum for dynamic settings: 0xf82ead67 | |
| Settings were read and verified. | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcFpmDriver::Init: Setting FPM Buffer size to: 2048 Base Address: 0x82f19da0 | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcFpmDriver::Init: fFpmLargestBufferSize: 2048 fFpmSizeShiftBits: 0xb | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcFpmDriver::Init: Pool index: 0 pool size: 2048 | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcFpmDriver::Init: Lookup table index: 0 pool size: 0 | |
| ------------------------------------ | |
| Free Pool Manager Configuration | |
| ------------------------------------ | |
| Buffer size in Bytes............... 2048 | |
| Number of Tokens................... 8192 | |
| Base Address of FPM Memory ........ 0xb2010200 | |
| Base Address of FPM Mem in DDR2.... 0x82f19da0 | |
| Total Configured FPM Memory Size... 16777216 | |
| Free Fifo Full..................... 0 | |
| Free Fifo Empty.................... 1 | |
| Alloc Fifo Full.................... 0 | |
| Alloc Fifo Empty................... 0 | |
| Number of tokens available......... 8192 | |
| Number of not valid token frees.... 0 | |
| Number of not valid token multi.... 0 | |
| Overflow Count..................... 0 | |
| Underflow Count.................... 0 | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcPacketAlloc::Init: Packet Alloc Header Buffer Start Addr: 0x82d61d80 Length: 0x1b8000 Max Buffer Size: 0xdc | |
| [00:00:00 01/01/1970] [Telnet Thread] BcmTelnetThread::ThreadMain: (Telnet Thread) Telnet server thread running... | |
| Creating SNMP agent cablemodem agent | |
| cablemodem agent disabling management. | |
| cablemodem agent defering traps. | |
| If you pressed the 's' key before this point, we will skip driver initialization... | |
| Creating TR-069 Thread... | |
| Creating DOCSIS Control Thread... | |
| vvv Interface creation and driver startup beginning vvv | |
| -> Begin Gfap HAL | |
| -> End GfInitalizing Gfap Hal.. | |
| ap HAL | |
| -> Begin DOCSIS CM WAN interface | |
| Creating HAL object for the DOCSIS CableModem interface | |
| Registering DOCSIS CableModem driver | |
| Initializing main DTP DQM interrupts. | |
| b4201000: 0000004c | |
| b4201004: 00000000 | |
| b4201008: 00000008 | |
| b420100c: 00000000 | |
| b4201010: 00000000 | |
| b4201014: 00000000 | |
| b4201018: 00000000 | |
| b420101c: 00000000 | |
| Creating a new host FAP DQM manager. Instance: 82cf0160 | |
| Creating a new host FAP DQM manager. Instance: 82cf005c | |
| Creating a new host UTP DQM manager. Instance: 82cebec8 | |
| Initializing main UTP DQM interrupts. | |
| b8001000: 0000000d | |
| b8001004: 00000000 | |
| b8001008: 00000008 | |
| b800100c: 00000000 | |
| b8001010: 00000001 | |
| b8001014: 00000000 | |
| b8001018: 00000000 | |
| b800101c: 00000000 | |
| LNA Detected = BCM3410 | |
| Initial Boost Status=0. Tilt Status=0 | |
| (Boost=Tilt=1)LNA Gain = 0x1f | |
| Final(Boost/Tilt=1/0) STATUS_READ2_REG=0x101f. | |
| ChipHalSelectPinMux: Setting pin mux sel 3, word 1, value 0 | |
| ChipHalSelectPinMux: Setting pin mux sel 1, word 1, value 0 | |
| Initializing all 8 downstreams - this takes a while. Patience, Grasshopper... | |
| 1 2 3 4 5 6 7 8 | |
| Fxtal is 48000000 | |
| Fclk_us_vco is 2088000000 | |
| Fclk_us_pll is 522000000 | |
| Fxtal is 48000000 | |
| Fclk_us_vco is 2088000000 | |
| Fclk_us_pll is 522000000 | |
| Fxtal is 48000000 | |
| Fclk_us_vco is 2088000000 | |
| Fclk_us_pll is 522000000 | |
| Fxtal is 48000000 | |
| Fclk_us_vco is 2088000000 | |
| Fclk_us_pll is 522000000 | |
| Fxtal is 48000000 | |
| Fclk_us_vco is 2088000000 | |
| Fclk_us_pll is 522000000 | |
| BcmMacInit: advMapRunAheadTimeMin = 3584 (0x00000e00) 10.24 MHz ticks, 350 usec | |
| Initializing DS Docsis 3.0 MAC | |
| Initializing CalcPhyPico | |
| BcmInitCalcPhyPico:Copying CalcPhy PicoCode rev 1.1.0 : 06/25/07 | |
| ...................................................................... | |
| Verifying CalcPhy PicoCode. | |
| ...................................................................... | |
| BcmInitCalcPhyPico:PicoCode verified. | |
| Creating a new host UTP DQM manager. Instance: 82ca7aa4 | |
| Creating a new host UTP DQM manager. Instance: 82ca79d0 | |
| [00:00:08 01/01/1970] [tStartup] BcmDocsisCmHalIf::Register: (DOCSIS CableModem HalIf) CM HAL reports h/w support for PHS, bitmask=0x3 | |
| [00:00:08 01/01/1970] [tStartup] BcmDocsisCmHalIf::Register: (DOCSIS CableModem HalIf) CM HAL reports h/w support for PHS, US size=64, DS size=256 bytes. | |
| -> End DOCSIS CM WAN interface | |
| -> Begin Ethernet LAN interfaces | |
| Creating HAL object for the Eth-Switch Lan(0) interface | |
| Registering Eth-Switch Lan(0) driver | |
| Creating a new host MSG PROC DQM manager. Instance: 82ca7150, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| Creating a new host MSG PROC DQM manager. Instance: 82ca707c, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| **** SETTING PHY DEFAULTS **** | |
| **** PEFORMING PHY CHECK **** | |
| >>>> Creating DQM bundle for DQM queue #: 3 | |
| Creating a new host MSG PROC DQM manager. Instance: 82ca6f08, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| >>>> Creating DQM bundle for DQM queue #: 0 | |
| Creating a new host MSG PROC DQM manager. Instance: 82ca6cfc, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| Enet Config GMAC UNIMAC Core: 1 Phy: 0 | |
| Ethernet Link Down! | |
| Number of Managed Switched Ports = 4 | |
| Creating HAL object for the Eth-Switch Lan(1) interface | |
| Registering Eth-Switch Lan(1) driver | |
| Creating HAL object for the Eth-Switch Lan(2) interface | |
| Registering Eth-Switch Lan(2) driver | |
| Creating HAL object for the Eth-Switch Lan(3) interface | |
| Registering Eth-Switch Lan(3) driver | |
| -> End Ethernet LAN interfaces | |
| -> Begin 802.11 WiFi LAN interface instance 0 | |
| Creating HAL object for (WiFi) interface #100 | |
| Registering (WiFi)(0)(0) Primary driver | |
| 802.11 country code in SROM query FAILED! | |
| 802.11 regulatory rev in SROM query FAILED! | |
| srom rev:8 | |
| WIFI INSTANCE 0 NIC DETECTED | |
| WiFi GPIO Configuration [WiFi Instance = 0] | |
| WiFi Device ID = 4353, Wifi Board Rev = 1202, WiFi Vendor ID = 14e4, WiFi WiFi Board ID = 4d8 | |
| Push Button: WiFi GPIO, Pin 0, Assert Level 0 | |
| WiFi Activity LED: WiFi GPIO, Pin 1, Assert Level 0 | |
| WPS 1 LED: WiFi GPIO, Pin 2, Assert Level 1 | |
| WPS 2 LED: WiFi GPIO, Pin 5, Assert Level 1 | |
| Vendor LED: UNDEFINED | |
| Error LED: UNDEFINED | |
| PCie Power On: UNDEFINED | |
| GPIO Extra Config: Reg Offset: 0x28, Mask Vale: 0x8000, Config Value: 0x8000 | |
| Creating HAL object for (WiFi) interface #101 | |
| Registering (WiFi)(0)(1) MBSS driver | |
| Creating HAL object for (WiFi) interface #102 | |
| Registering (WiFi)(0)(2) MBSS driver | |
| Creating HAL object for (WiFi) interface #103 | |
| Registering (WiFi)(0)(3) MBSS driver | |
| Creating HAL object for (WiFi) interface #104 | |
| Registering (WiFi)(0)(4) MBSS driver | |
| Creating HAL object for (WiFi) interface #105 | |
| Registering (WiFi)(0)(5) MBSS driver | |
| Creating HAL object for (WiFi) interface #106 | |
| Registering (WiFi)(0)(6) MBSS driver | |
| Creating HAL object for (WiFi) interface #107 | |
| Registering (WiFi)(0)(7) MBSS driver | |
| Creating HAL object for (WiFi) interface #108 | |
| Registering (WiFi)(0)(8) WDS driver | |
| Creating HAL object for (WiFi) interface #109 | |
| Registering (WiFi)(0)(9) WDS driver | |
| Creating HAL object for (WiFi) interface #110 | |
| Registering (WiFi)(0)(10) WDS driver | |
| Creating HAL object for (WiFi) interface #111 | |
| Registering (WiFi)(0)(11) WDS driver | |
| BcmWiFi80211NiHalIf::PrefetchMacAddresses | |
| MAC Address of SSID 0 : f0:7b:cb:5f:6f:e2 | |
| MAC Address of SSID 1 : f2:7b:cb:5f:6f:e3 | |
| MAC Address of SSID 2 : f2:7b:cb:5f:6f:e4 | |
| MAC Address of SSID 3 : f2:7b:cb:5f:6f:e5 | |
| MAC Address of SSID 4 : f2:7b:cb:5f:6f:e6 | |
| MAC Address of SSID 5 : f2:7b:cb:5f:6f:e7 | |
| **** PEFORMING PHY CHECK **** | |
| MAC Address of SSID 6 : f2:7b:cb:5f:6f:e8 | |
| MAC Address of SSID 7 : f2:7b:cb:5f:6f:e9 | |
| wl: Unsupported | |
| -> End 802.11 WiFi LAN interfaces. | |
| nas_main: Thread creation ok | |
| nas_main: Thread start ok | |
| BcmWpsPBCThread: Thread creation ok | |
| wpsPBCStart: Thread start ok | |
| -> Begin IP Stacwps_main: upnp I/F not up yet... | |
| k interfaces | |
| -> Starting BFC DHCP Client subsystem... | |
| -> Starting BFC DHCPv6 Client subsystem... | |
| Creating HAL object for IP Stack1 (MAC Addr=f8:2f:a8:bb:83:99) | |
| Registering IP Stack1 driver | |
| Tcpip NI: Init - RegisteredStackCount = 1 | |
| Creating HAL object for IP Stack2 (MAC Addr=00:d0:59:de:ad:02) | |
| Registering IP Stack2 driver | |
| Tcpip NI: Init - RegisteredStackCount = 2 | |
| Creating HAL object for IP Stack3 (MAC Addr=f8:2f:a8:bb:83:9a) | |
| Registering IP Stack3 driver | |
| Tcpip NI: Init - RegisteredStackCount = 3 | |
| Creating HAL object for IP Stack4 (MAC Addr=00:d0:59:de:ad:04) | |
| Registering IP Stack4 driver | |
| Tcpip NI: Init - RegisteredStackCount = 4 | |
| Creating HAL object for IP Stack5 (MAC Addr=f8:2f:a8:bb:83:9b) | |
| Registering IP Stack5 driver | |
| Tcpip NI: Init - RegisteredStackCount = 5 | |
| -> End IP Stack interfaces | |
| USB host subsytem intilialized | |
| Successfully mapped HCD interrupt 12 | |
| Registered BRCM USB HCD with USB Host subytem | |
| ^^^ Interface creation and driver startup complete ^^^ | |
| Forward Assist Manager Starting... | |
| Creating the eRouter Forwarder... | |
| Adding Eth-Switch Lan(0) HalIf to the eRouter Forwarder | |
| Adding Eth-Switch Lan(1) HalIf to the eRouter Forwarder | |
| Adding Eth-Switch Lan(2) HalIf to the eRouter Forwarder | |
| Adding Eth-Switch Lan(3) HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(0) Primary HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(1) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(2) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(3) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(4) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(5) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(6) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(7) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(8) WDS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(9) WDS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(10) WDS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(11) WDS HalIf to the eRouter Forwarder | |
| Adding IP Stack3 HalIf to the eRouter Forwarder | |
| Adding IP Stack4 HalIf to the eRouter Forwarder | |
| Adding IP Stack5 HalIf to the eRouter Forwarder | |
| Creating the DOCSIS Forwarder... | |
| Adding DOCSIS CableModem HalIf as the default interface to the DOCSIS Forwarder | |
| Adding IP Stack1 HalIf to the DOCSIS Forwarder | |
| Adding IP Stack2 HalIf to the DOCSIS Forwarder | |
| Adding WAN-Man Interface HalIf as the default interface to the eRouter Forwarder | |
| Adding Ethernet CPE Interface All HalIf to the DOCSIS Forwarder | |
| [00:00:10 01/01/1970] [tStartup] BcmEpsCmDocsisSystem::InstallMiniUsfs: (BFC System) Installing Mini-Usfs snoop | |
| Current IP address is default 0.0.0.0. | |
| Configuring IP stack 2: IP Address = 192.168.100.1 | |
| SES2WindowClosed! (unexpected) | |
| [00:00:11 01/01/1970] [tStartup] BcmEcosIpHalIf::AddIpv6LinkLocalAddress: (IP Stack2 HalIf) Configuring link-local IPv6 address fe80::2d0:59ff:fede:ad02/64 | |
| Creating Propane Control Thread... | |
| Propane version: 2.0.1 (28 Oct 2002) | |
| Instantiating CmSnmpAgent object. | |
| Starting SNMP subsystem | |
| Registering STP Filter Snoop with all interfaces. | |
| Registering DOCSIS MIB Filter Snoop with CPE and WAN interfaces. | |
| Creating SNMP agent CPE diag agent | |
| CPE diag agent disabling management. | |
| CPE diag agent defering traps. | |
| BcmSnmpThread starting thread operation. | |
| Initializing Net-SNMP transport for IPv4 | |
| Initializing Net-SNMP transport for IPv6 | |
| IPv6 - register netsnmp_brcmV6_ctor to get our brcm V6 UDP domain | |
| IPv6 init_bcmV2SessionAndTransport: Open a session and hook our callbacks | |
| ERROR! Can't add twcDeviceGroup to cableModemMibGroup, 1.3.6.1.4.1.1174.100 doesn't descend from 1.3.6.1.4.1.4684.2 | |
| [00:00:13 01/01/1970] [tStartup] BcmDocsisCmHalIf::RegisterSnmpObjects: (DOCSIS CableModem HalIf) Interface 10 additional registration w/ SNMP agent OK. | |
| [00:00:13 01/01/1970] [tStartup] BcmErouterPacketSwitchBridgingHalIf::RegisterSnmpObjects: (Ethernet CPE Interface All HalIf) Interface 39 additional registration w/ SNMP agent OK. | |
| Setting US cal singleton instance to 0 | |
| Register:: SKIPPPING index 13 | |
| Register:: SKIPPPING index 14 | |
| Register:: SKIPPPING index 15 | |
| Register:: SKIPPPING index 16 | |
| Register:: SKIPPPING index 17 | |
| Register:: SKIPPPING index 18 | |
| Register:: SKIPPPING index 19 | |
| BcmCommandTable::AddInstance: ERROR - Attempted to add duplicate instance 'FoxAgwThread' (0x82a663b8) to command table 'Message Log Settings Commands'. | |
| CmSnmpAgent installing views... | |
| CmSnmpAgent installing DOCSIS Default View entries... | |
| Vendor CM Agent w/ BRCM Factory Support setting V1/V2 view to unrestricted | |
| BCM338031 TP0 | |
| 1 | |
| Sync:1 | |
| 346890 | |
| MemSize: 64 M | |
| BootLoader Version: 10.1.2 Release Gnu spiboot reduced DDR drive | |
| Build Date: Dec 23 2009 | |
| Build Time: 15:43:35 | |
| SPI flash ID 0xc22017, size 8MB, block size 64KB, write buffer 256, busy bit 1 | |
| Signature/PID: a623 | |
| Image 1 Program Header: | |
| Signature: a623 | |
| Control: 0005 | |
| Major Rev: 0003 | |
| Minor Rev: 0000 | |
| Build Time: 2014/10/1 06:48:25 Z | |
| File Length: 3629577 bytes | |
| Load Address: 80004000 | |
| Filename: ecram_sto.bin | |
| HCS: c7fd | |
| CRC: 7957ca46 | |
| Found image 1 at offset 20000 | |
| Image 2 Program Header: | |
| Signature: a623 | |
| Control: 0005 | |
| Major Rev: 0003 | |
| Minor Rev: 0000 | |
| Build Time: 2015/3/9 08:23:39 Z | |
| File Length: 3629299 bytes | |
| Load Address: 80004000 | |
| Filename: ecram_sto.bin | |
| HCS: 18aa | |
| CRC: 364190e3 | |
| Found image 2 at offset 400000 | |
| Enter '1', '2', or 'p' within 2 seconds or take default... | |
| . . | |
| Performing CRC on Image 2... | |
| CRC time = 57361392 | |
| Detected LZMA compressed image... decompressing... | |
| Target Address: 0x80004000 | |
| decompressSpace is 0x4000000 | |
| Elapsed time 1152135662 | |
| Decompressed length: 18941436 | |
| Executing Image 2... | |
| eCos - hal_diag_init | |
| Init device '/dev/BrcmTelnetIoDriver' | |
| Init device '/dev/ttydiag' | |
| Init tty channel: 81214070 | |
| Init device '/dev/tty0' | |
| Init tty channel: 81214090 | |
| Init device '/dev/haldiag' | |
| HAL/diag SERIAL init | |
| Init device '/dev/ser0' | |
| BCM 33XX SERIAL init - dev: b4e00200.2 | |
| Set output buffer - buf: 0x812f4cc8 len: 4096 | |
| Set input buffer - buf: 0x812f5cc8 len: 4096 | |
| BCM 33XX SERIAL config | |
| Init device '/dev/ser1' | |
| BCM 33XX SERIAL init - dev: b4e00220.3 | |
| Set output buffer - buf: 0x812f6cc8 len: 4096 | |
| Set input buffer - buf: 0x812f7cc8 len: 4096 | |
| BCM 33XX SERIAL config | |
| LsSpiInit 3380 | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Configuring/Loading Flash driver... | |
| [00:00:00 01/01/1970] [tStartup] BcmSpiFlashDevice::DetectFlash: (SPI Flash Device Factory) WARNING - Detected SPI flash with JEDEC ID =0xc22017 | |
| [00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::SpiFlashPlaceRegions: (Flash Driver C API) WARNING - Permanent NonVol would fit in the boot block of this flash device, but I found existing NonVol in the following block; using this location instead... | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading BootloaderStore driver... | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading ProgramStore driver... | |
| ProgramStoreDeviceDriver::ProgramStoreDriverInit: INFO - Initializing... | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading NonVol driver... | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Storage drivers initialized successfully. | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Creating singletons for ProgramStore/BootloaderStore/NonVol devices... | |
| Detecting the next image number that we will store to by default... | |
| Bootloader indicates we are running image 2 | |
| By default, we will dload to image number 1! | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Device abstraction singletons created successfully. | |
| BcmHalIfNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! | |
| BcmHalIfNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! | |
| BcmHalIfNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! | |
| FoxRgNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! | |
| Reading Permanent settings from non-vol... | |
| Checksum for permanent settings: 0x9b7c5ed8 | |
| Setting downstream calibratiChipHalSelectPinMux: Setting pin mux sel 18, word 0, value 2 | |
| ChipHalSelectPinMux: Setting pin mux sel 21, word 0, value 1 | |
| ChipHalSelectPinMux: Setting pin mux sel 13, word 0, value 0 | |
| on signature to '' | |
| Setting downstream calibration signature Creating a new host MSG PROC DQM manager. Instance: 83f730c0, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| Initializing main MSG_PROC DQM interrupts. | |
| b8801000: 00000000 | |
| b8801004: 00000000 | |
| b8801008: 00000008 | |
| b880100c: 00000000 | |
| b8801010: 00000000 | |
| b8801014: 00000000 | |
| b8801018: 00000000 | |
| b880101c: 00000000 | |
| to '' | |
| Settings were read and Creating a new host FAP DQM manager. Instance: 83f7304c | |
| Initializing main FAP DQM interrupts. | |
| b8401000: 00000000 | |
| b8401004: 00000000 | |
| b8401008: 00000008 | |
| b840100c: 00000000 | |
| b8401010: 00000000 | |
| b8401014: 00000000 | |
| b8401018: 00000000 | |
| b840101c: 00000000 | |
| verified. | |
| ############################################# | |
| ### Copied settings from tuner 0 to tuner 1 | |
| ############################################# | |
| Reading Dynamic settings from non-vol... | |
| Checksum for dynamic settings: 0xf72ead67 | |
| Settings were read and verified. | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcFpmDriver::Init: Setting FPM Buffer size to: 2048 Base Address: 0x82f19da0 | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcFpmDriver::Init: fFpmLargestBufferSize: 2048 fFpmSizeShiftBits: 0xb | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcFpmDriver::Init: Pool index: 0 pool size: 2048 | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcFpmDriver::Init: Lookup table index: 0 pool size: 0 | |
| ------------------------------------ | |
| Free Pool Manager Configuration | |
| ------------------------------------ | |
| Buffer size in Bytes............... 2048 | |
| Number of Tokens................... 8192 | |
| Base Address of FPM Memory ........ 0xb2010200 | |
| Base Address of FPM Mem in DDR2.... 0x82f19da0 | |
| Total Configured FPM Memory Size... 16777216 | |
| Free Fifo Full..................... 0 | |
| Free Fifo Empty.................... 1 | |
| Alloc Fifo Full.................... 0 | |
| Alloc Fifo Empty................... 0 | |
| Number of tokens available......... 8192 | |
| Number of not valid token frees.... 0 | |
| Number of not valid token multi.... 0 | |
| Overflow Count..................... 0 | |
| Underflow Count.................... 0 | |
| [00:00:00 01/01/1970] [tStartup] BcmBfcPacketAlloc::Init: Packet Alloc Header Buffer Start Addr: 0x82d61d80 Length: 0x1b8000 Max Buffer Size: 0xdc | |
| [00:00:00 01/01/1970] [Telnet Thread] BcmTelnetThread::ThreadMain: (Telnet Thread) Telnet server thread running... | |
| Creating SNMP agent cablemodem agent | |
| cablemodem agent disabling management. | |
| cablemodem agent defering traps. | |
| If you pressed the 's' key before this point, we will skip driver initialization... | |
| Creating TR-069 Thread... | |
| Creating DOCSIS Control Thread... | |
| vvv Interface creation and driver startup beginning vvv | |
| -> Begin Gfap HAL | |
| -> End GfInitalizing Gfap Hal.. | |
| ap HAL | |
| -> Begin DOCSIS CM WAN interface | |
| Creating HAL object for the DOCSIS CableModem interface | |
| Registering DOCSIS CableModem driver | |
| Initializing main DTP DQM interrupts. | |
| b4201000: 0000004c | |
| b4201004: 00000000 | |
| b4201008: 00000008 | |
| b420100c: 00000000 | |
| b4201010: 00000000 | |
| b4201014: 00000000 | |
| b4201018: 00000000 | |
| b420101c: 00000000 | |
| Creating a new host FAP DQM manager. Instance: 82cf0160 | |
| Creating a new host FAP DQM manager. Instance: 82cf005c | |
| Creating a new host UTP DQM manager. Instance: 82cebec8 | |
| Initializing main UTP DQM interrupts. | |
| b8001000: 0000000d | |
| b8001004: 00000000 | |
| b8001008: 00000008 | |
| b800100c: 00000000 | |
| b8001010: 00000001 | |
| b8001014: 00000000 | |
| b8001018: 00000000 | |
| b800101c: 00000000 | |
| LNA Detected = BCM3410 | |
| Initial Boost Status=0. Tilt Status=0 | |
| (Boost=Tilt=1)LNA Gain = 0x1f | |
| Final(Boost/Tilt=1/0) STATUS_READ2_REG=0x101f. | |
| ChipHalSelectPinMux: Setting pin mux sel 3, word 1, value 0 | |
| ChipHalSelectPinMux: Setting pin mux sel 1, word 1, value 0 | |
| Initializing all 8 downstreams - this takes a while. Patience, Grasshopper... | |
| 1 2 3 4 5 6 7 8 | |
| Fxtal is 48000000 | |
| Fclk_us_vco is 2088000000 | |
| Fclk_us_pll is 522000000 | |
| Fxtal is 48000000 | |
| Fclk_us_vco is 2088000000 | |
| Fclk_us_pll is 522000000 | |
| Fxtal is 48000000 | |
| Fclk_us_vco is 2088000000 | |
| Fclk_us_pll is 522000000 | |
| Fxtal is 48000000 | |
| Fclk_us_vco is 2088000000 | |
| Fclk_us_pll is 522000000 | |
| Fxtal is 48000000 | |
| Fclk_us_vco is 2088000000 | |
| Fclk_us_pll is 522000000 | |
| BcmMacInit: advMapRunAheadTimeMin = 3584 (0x00000e00) 10.24 MHz ticks, 350 usec | |
| Initializing DS Docsis 3.0 MAC | |
| Initializing CalcPhyPico | |
| BcmInitCalcPhyPico:Copying CalcPhy PicoCode rev 1.1.0 : 06/25/07 | |
| ...................................................................... | |
| Verifying CalcPhy PicoCode. | |
| ...................................................................... | |
| BcmInitCalcPhyPico:PicoCode verified. | |
| Creating a new host UTP DQM manager. Instance: 82ca7aa4 | |
| Creating a new host UTP DQM manager. Instance: 82ca79d0 | |
| [00:00:08 01/01/1970] [tStartup] BcmDocsisCmHalIf::Register: (DOCSIS CableModem HalIf) CM HAL reports h/w support for PHS, bitmask=0x3 | |
| [00:00:08 01/01/1970] [tStartup] BcmDocsisCmHalIf::Register: (DOCSIS CableModem HalIf) CM HAL reports h/w support for PHS, US size=64, DS size=256 bytes. | |
| -> End DOCSIS CM WAN interface | |
| -> Begin Ethernet LAN interfaces | |
| Creating HAL object for the Eth-Switch Lan(0) interface | |
| Registering Eth-Switch Lan(0) driver | |
| Creating a new host MSG PROC DQM manager. Instance: 82ca7150, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| Creating a new host MSG PROC DQM manager. Instance: 82ca707c, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| **** SETTING PHY DEFAULTS **** | |
| **** PEFORMING PHY CHECK **** | |
| >>>> Creating DQM bundle for DQM queue #: 3 | |
| Creating a new host MSG PROC DQM manager. Instance: 82ca6f08, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| >>>> Creating DQM bundle for DQM queue #: 0 | |
| Creating a new host MSG PROC DQM manager. Instance: 82ca6cfc, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| Enet Config GMAC UNIMAC Core: 1 Phy: 0 | |
| Ethernet Link Down! | |
| Number of Managed Switched Ports = 4 | |
| Creating HAL object for the Eth-Switch Lan(1) interface | |
| Registering Eth-Switch Lan(1) driver | |
| Creating HAL object for the Eth-Switch Lan(2) interface | |
| Registering Eth-Switch Lan(2) driver | |
| Creating HAL object for the Eth-Switch Lan(3) interface | |
| Registering Eth-Switch Lan(3) driver | |
| -> End Ethernet LAN interfaces | |
| -> Begin 802.11 WiFi LAN interface instance 0 | |
| Creating HAL object for (WiFi) interface #100 | |
| Registering (WiFi)(0)(0) Primary driver | |
| 802.11 country code in SROM query FAILED! | |
| 802.11 regulatory rev in SROM query FAILED! | |
| srom rev:8 | |
| WIFI INSTANCE 0 NIC DETECTED | |
| WiFi GPIO Configuration [WiFi Instance = 0] | |
| WiFi Device ID = 4353, Wifi Board Rev = 1202, WiFi Vendor ID = 14e4, WiFi WiFi Board ID = 4d8 | |
| Push Button: WiFi GPIO, Pin 0, Assert Level 0 | |
| WiFi Activity LED: WiFi GPIO, Pin 1, Assert Level 0 | |
| WPS 1 LED: WiFi GPIO, Pin 2, Assert Level 1 | |
| WPS 2 LED: WiFi GPIO, Pin 5, Assert Level 1 | |
| Vendor LED: UNDEFINED | |
| Error LED: UNDEFINED | |
| PCie Power On: UNDEFINED | |
| GPIO Extra Config: Reg Offset: 0x28, Mask Vale: 0x8000, Config Value: 0x8000 | |
| Creating HAL object for (WiFi) interface #101 | |
| Registering (WiFi)(0)(1) MBSS driver | |
| Creating HAL object for (WiFi) interface #102 | |
| Registering (WiFi)(0)(2) MBSS driver | |
| Creating HAL object for (WiFi) interface #103 | |
| Registering (WiFi)(0)(3) MBSS driver | |
| Creating HAL object for (WiFi) interface #104 | |
| Registering (WiFi)(0)(4) MBSS driver | |
| Creating HAL object for (WiFi) interface #105 | |
| Registering (WiFi)(0)(5) MBSS driver | |
| Creating HAL object for (WiFi) interface #106 | |
| Registering (WiFi)(0)(6) MBSS driver | |
| Creating HAL object for (WiFi) interface #107 | |
| Registering (WiFi)(0)(7) MBSS driver | |
| Creating HAL object for (WiFi) interface #108 | |
| Registering (WiFi)(0)(8) WDS driver | |
| Creating HAL object for (WiFi) interface #109 | |
| Registering (WiFi)(0)(9) WDS driver | |
| Creating HAL object for (WiFi) interface #110 | |
| Registering (WiFi)(0)(10) WDS driver | |
| Creating HAL object for (WiFi) interface #111 | |
| Registering (WiFi)(0)(11) WDS driver | |
| BcmWiFi80211NiHalIf::PrefetchMacAddresses | |
| MAC Address of SSID 0 : f0:7b:cb:5f:6f:e2 | |
| MAC Address of SSID 1 : f2:7b:cb:5f:6f:e3 | |
| MAC Address of SSID 2 : f2:7b:cb:5f:6f:e4 | |
| MAC Address of SSID 3 : f2:7b:cb:5f:6f:e5 | |
| MAC Address of SSID 4 : f2:7b:cb:5f:6f:e6 | |
| MAC Address of SSID 5 : f2:7b:cb:5f:6f:e7 | |
| **** PEFORMING PHY CHECK **** | |
| MAC Address of SSID 6 : f2:7b:cb:5f:6f:e8 | |
| MAC Address of SSID 7 : f2:7b:cb:5f:6f:e9 | |
| wl: Unsupported | |
| -> End 802.11 WiFi LAN interfaces. | |
| nas_main: Thread creation ok | |
| nas_main: Thread start ok | |
| BcmWpsPBCThread: Thread creation ok | |
| wpsPBCStart: Thread start ok | |
| -> Begin IP Stawps_main: upnp I/F not up yet... | |
| ck interfaces | |
| -> Starting BFC DHCP Client subsystem... | |
| -> Starting BFC DHCPv6 Client subsystem... | |
| Creating HAL object for IP Stack1 (MAC Addr=f8:2f:a8:bb:83:99) | |
| Registering IP Stack1 driver | |
| Tcpip NI: Init - RegisteredStackCount = 1 | |
| Creating HAL object for IP Stack2 (MAC Addr=00:d0:59:de:ad:02) | |
| Registering IP Stack2 driver | |
| Tcpip NI: Init - RegisteredStackCount = 2 | |
| Creating HAL object for IP Stack3 (MAC Addr=f8:2f:a8:bb:83:9a) | |
| Registering IP Stack3 driver | |
| Tcpip NI: Init - RegisteredStackCount = 3 | |
| Creating HAL object for IP Stack4 (MAC Addr=00:d0:59:de:ad:04) | |
| Registering IP Stack4 driver | |
| Tcpip NI: Init - RegisteredStackCount = 4 | |
| Creating HAL object for IP Stack5 (MAC Addr=f8:2f:a8:bb:83:9b) | |
| Registering IP Stack5 driver | |
| Tcpip NI: Init - RegisteredStackCount = 5 | |
| -> End IP Stack interfaces | |
| USB host subsytem intilialized | |
| Successfully mapped HCD interrupt 12 | |
| Registered BRCM USB HCD with USB Host subytem | |
| ^^^ Interface creation and driver startup complete ^^^ | |
| Forward Assist Manager Starting... | |
| Creating the eRouter Forwarder... | |
| Adding Eth-Switch Lan(0) HalIf to the eRouter Forwarder | |
| Adding Eth-Switch Lan(1) HalIf to the eRouter Forwarder | |
| Adding Eth-Switch Lan(2) HalIf to the eRouter Forwarder | |
| Adding Eth-Switch Lan(3) HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(0) Primary HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(1) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(2) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(3) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(4) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(5) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(6) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(7) MBSS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(8) WDS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(9) WDS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(10) WDS HalIf to the eRouter Forwarder | |
| Adding (WiFi)(0)(11) WDS HalIf to the eRouter Forwarder | |
| Adding IP Stack3 HalIf to the eRouter Forwarder | |
| Adding IP Stack4 HalIf to the eRouter Forwarder | |
| Adding IP Stack5 HalIf to the eRouter Forwarder | |
| Creating the DOCSIS Forwarder... | |
| Adding DOCSIS CableModem HalIf as the default interface to the DOCSIS Forwarder | |
| Adding IP Stack1 HalIf to the DOCSIS Forwarder | |
| Adding IP Stack2 HalIf to the DOCSIS Forwarder | |
| Adding WAN-Man Interface HalIf as the default interface to the eRouter Forwarder | |
| Adding Ethernet CPE Interface All HalIf to the DOCSIS Forwarder | |
| [00:00:10 01/01/1970] [tStartup] BcmEpsCmDocsisSystem::InstallMiniUsfs: (BFC System) Installing Mini-Usfs snoop | |
| Current IP address is default 0.0.0.0. | |
| Configuring IP stack 2: IP Address = 192.168.100.1 | |
| SES2WindowClosed! (unexpected) | |
| [00:00:11 01/01/1970] [tStartup] BcmEcosIpHalIf::AddIpv6LinkLocalAddress: (IP Stack2 HalIf) Configuring link-local IPv6 address fe80::2d0:59ff:fede:ad02/64 | |
| Creating Propane Control Thread... | |
| Propane version: 2.0.1 (28 Oct 2002) | |
| Instantiating CmSnmpAgent object. | |
| Starting SNMP subsystem | |
| Registering STP Filter Snoop with all interfaces. | |
| Registering DOCSIS MIB Filter Snoop with CPE and WAN interfaces. | |
| Creating SNMP agent CPE diag agent | |
| CPE diag agent disabling management. | |
| CPE diag agent defering traps. | |
| BcmSnmpThread starting thread operation. | |
| Initializing Net-SNMP transport for IPv4 | |
| Initializing Net-SNMP transport for IPv6 | |
| IPv6 - register netsnmp_brcmV6_ctor to get our brcm V6 UDP domain | |
| IPv6 init_bcmV2SessionAndTransport: Open a session and hook our callbacks | |
| ERROR! Can't add twcDeviceGroup to cableModemMibGroup, 1.3.6.1.4.1.1174.100 doesn't descend from 1.3.6.1.4.1.4684.2 | |
| [00:00:13 01/01/1970] [tStartup] BcmDocsisCmHalIf::RegisterSnmpObjects: (DOCSIS CableModem HalIf) Interface 10 additional registration w/ SNMP agent OK. | |
| [00:00:13 01/01/1970] [tStartup] BcmErouterPacketSwitchBridgingHalIf::RegisterSnmpObjects: (Ethernet CPE Interface All HalIf) Interface 39 additional registration w/ SNMP agent OK. | |
| Setting US cal singleton instance to 0 | |
| Register:: SKIPPPING index 13 | |
| Register:: SKIPPPING index 14 | |
| Register:: SKIPPPING index 15 | |
| Register:: SKIPPPING index 16 | |
| Register:: SKIPPPING index 17 | |
| Register:: SKIPPPING index 18 | |
| Register:: SKIPPPING index 19 | |
| BcmCommandTable::AddInstance: ERROR - Attempted to add duplicate instance 'FoxAgwThread' (0x82a663b8) to command table 'Message Log Settings Commands'. | |
| CmSnmpAgent installing views... | |
| CmSnmpAgent installing DOCSIS Default View entries... | |
| Vendor CM Agent w/ BRCM Factory Support setting V1/V2 view to unrestricted | |
| Vendor CM Agent w/ BRCM Factory Support installing engine ID... | |
| Vendor CM Agent w/ BRCM Factory Support installing context... | |
| NAT Session Manager: PSM start is @ 15810000 (3380) | |
| Creating a new host MSG PROC DQM manager. Instance: 82a25b70, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| InitializeNapDqmMessageChannel SUCCESS! | |
| hostNapHalIf: InitializeNapDqmMessageChannel SUCCESS! | |
| NatTrafficCounterPsmOffset SUCCESS! | |
| Counter PSM Offset is 17952 | |
| DMA4 replace PSM Offset is 5664 | |
| DMA6 replace PSM Offset is 14368 | |
| DMA checksum PSM Offset is 32 | |
| NatpFfeOffsets SUCCESS! | |
| FFE HASH4 0 Bin Offset is 57 | |
| FFE HASH6 0 Bin Offset is 607 | |
| FFE DMA4 REPLACE Offset is 217 | |
| FFE DMA6 REPLACE Offset is 767 | |
| SNMP startup complete. | |
| ************************************ | |
| *** Start up CPU load monitor module | |
| ************************************ | |
| [[00:00:15 01/01Creating a new host MSG PROC DQM manager. Instance: 82a0ccc4, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| Creating a new host MSG PROC DQM manager. Instance: 82a0cc08, DQM_REGS = b8801800, CTRL_REGS = b8801000 | |
| wps_main: upnp I/F not up yet... | |
| /1970] [tStartup] BcmDocsisCmHalIf::AddSnoop: (DOCSIS CableModem HalIf) WARNING - VendorPacketSnoop: unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:15 01/01/1970] [tStartup] BcmDocsisCmHalIf::SortSnoops: (DOCSIS CableModem HalIf) WARNING - Unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:15 01/01/1970] [tStartup] BcmDocsisCmHalIf::AddSnoop: (DOCSIS CableModem HalIf) WARNING - VendorPacketSnoop: unsafe modification of the Snoop lists after the interface is up! | |
| [00:00:15 01/01/1970] [tStartup] BcmDocsisCmHalIf::SortSnoops: (DOCSIS CableModem HalIf) WARNING - Unsafe modification of the Snoop lists after the interface is up! | |
| BcmCommandTable::AddInstance: ERROR - Attempted to add duplicate instance 'ND Thread for IP Stack1' (0x829fbd3c) to command table 'Message Log Settings Commands'. | |
| Current IP address is default 0.0.0.0. | |
| Configuring IP stack 5: IP Address = 192.168.0.1 | |
| 0V[0: 0:15 1/ 1/1970] [NAT Session Manager Thread] BcmNatSessionManagerThread::ThreadMain: (NAT Session Manager Thread) NAT Session Manager waiting for events... | |
| 00:00:15 01/01/1970] [FTP Lite Client Thread] FtpLiteClientTh | |
| BCM338031 TP0 | |
| 1 | |
| Sync:1 | |
| 346890 | |
| MemSize: 64 M | |
| BootLoader Version: 10.1.2 Release Gnu spiboot reduced DDR drive | |
| Build Date: Dec 23 2009 | |
| Build Time: 15:43:35 | |
| SPI flash ID 0xc22017, size 8MB, block size 64KB, write buffer 256, busy bit 1 | |
| Signature/PID: a623 | |
| Image 1 Program Header: | |
| Signature: a623 | |
| Control: 0005 | |
| Major Rev: 0003 | |
| Minor Rev: 0000 | |
| Build Time: 2014/10/1 06:48:25 Z | |
| File Length: 3629577 bytes | |
| Load Address: 80004000 | |
| Filename: ecram_sto.bin | |
| HCS: c7fd | |
| CRC: 7957ca46 | |
| Found image 1 at offset 20000 | |
| Image 2 Program Header: | |
| Signature: a623 | |
| Control: 0005 | |
| Major Rev: 0003 | |
| Minor Rev: 0000 | |
| Build Time: 2015/3/9 08:23:39 Z | |
| File Length: 3629299 bytes | |
| Load Address: 80004000 | |
| Filename: ecram_sto.bin | |
| HCS: 18aa | |
| CRC: 364190e3 | |
| Found image 2 at offset 400000 | |
| Enter '1', '2', or 'p' within 2 seconds or take default... | |
| . . |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment