Created
February 23, 2018 15:52
-
-
Save Darker/b881eae8655c8f3938b595395f7db662 to your computer and use it in GitHub Desktop.
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| # generated by Slic3r 1.3.0-dev on Fri Feb 23 16:52:42 2018 | |
| [filament:ColorFabb Brass Bronze 1.75mm] | |
| bed_temperature = 50 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| cooling = 1 | |
| disable_fan_first_layers = 1 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 100 | |
| filament_colour = #B79A39 | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 50 | |
| first_layer_temperature = 210 | |
| max_fan_speed = 100 | |
| min_fan_speed = 85 | |
| min_print_speed = 5 | |
| slowdown_below_layer_time = 20 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 210 | |
| [filament:ColorFabb Wood Bamboo 1.75mm] | |
| bed_temperature = 50 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| cooling = 1 | |
| disable_fan_first_layers = 1 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 100 | |
| filament_colour = #5A4110 | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 50 | |
| first_layer_temperature = 210 | |
| max_fan_speed = 100 | |
| min_fan_speed = 85 | |
| min_print_speed = 5 | |
| slowdown_below_layer_time = 20 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 210 | |
| [filament:ColorFabb XT 1.75mm] | |
| bed_temperature = 65 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 20 | |
| filament_colour = #A36FFD | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 90 | |
| first_layer_temperature = 240 | |
| max_fan_speed = 50 | |
| min_fan_speed = 30 | |
| min_print_speed = 5 | |
| slowdown_below_layer_time = 15 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 240 | |
| [filament:ColorFabb XT-CF20 1.75mm] | |
| bed_temperature = 65 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 20 | |
| filament_colour = #000000 | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 90 | |
| first_layer_temperature = 240 | |
| max_fan_speed = 50 | |
| min_fan_speed = 30 | |
| min_print_speed = 5 | |
| slowdown_below_layer_time = 15 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 250 | |
| [filament:Fillamentum ABS 1.75mm] | |
| bed_temperature = 100 | |
| bridge_fan_speed = 30 | |
| compatible_printers = | |
| cooling = 0 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 20 | |
| filament_colour = #3A80CA | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 100 | |
| first_layer_temperature = 255 | |
| max_fan_speed = 30 | |
| min_fan_speed = 10 | |
| min_print_speed = 5 | |
| slowdown_below_layer_time = 15 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 255 | |
| [filament:MY Prusa PLA 1.75mm] | |
| bed_temperature = 50 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| cooling = 1 | |
| disable_fan_first_layers = 1 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 100 | |
| filament_colour = #FFFFFF | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 50 | |
| first_layer_temperature = 210 | |
| max_fan_speed = 100 | |
| min_fan_speed = 85 | |
| min_print_speed = 5 | |
| slowdown_below_layer_time = 20 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 210 | |
| [filament:Prusa ABS 1.75mm] | |
| bed_temperature = 100 | |
| bridge_fan_speed = 30 | |
| compatible_printers = | |
| cooling = 0 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 20 | |
| filament_colour = #3A80CA | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 100 | |
| first_layer_temperature = 255 | |
| max_fan_speed = 30 | |
| min_fan_speed = 10 | |
| min_print_speed = 5 | |
| slowdown_below_layer_time = 15 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 255 | |
| [filament:Prusa FLEX 1.75mm] | |
| bed_temperature = 50 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| cooling = 0 | |
| disable_fan_first_layers = 1 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 100 | |
| filament_colour = #00CA0A | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 50 | |
| first_layer_temperature = 230 | |
| max_fan_speed = 90 | |
| min_fan_speed = 70 | |
| min_print_speed = 5 | |
| slowdown_below_layer_time = 10 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 230 | |
| [filament:Prusa HIPS 1.75mm] | |
| bed_temperature = 100 | |
| bridge_fan_speed = 80 | |
| compatible_printers = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 0.9 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 20 | |
| filament_colour = #FFE130 | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 100 | |
| first_layer_temperature = 220 | |
| max_fan_speed = 80 | |
| min_fan_speed = 50 | |
| min_print_speed = 5 | |
| slowdown_below_layer_time = 15 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 220 | |
| [filament:Prusa PET 1.75mm] | |
| bed_temperature = 90 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 20 | |
| filament_colour = #B5F5FD | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 90 | |
| first_layer_temperature = 240 | |
| max_fan_speed = 50 | |
| min_fan_speed = 30 | |
| min_print_speed = 5 | |
| slowdown_below_layer_time = 15 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 240 | |
| [filament:Prusa PLA 1.75mm] | |
| bed_temperature = 50 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| cooling = 1 | |
| disable_fan_first_layers = 1 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 100 | |
| filament_colour = #FF14E2 | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 50 | |
| first_layer_temperature = 210 | |
| max_fan_speed = 100 | |
| min_fan_speed = 85 | |
| min_print_speed = 5 | |
| slowdown_below_layer_time = 20 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 210 | |
| [filament:Taulman Bridge 1.75mm] | |
| bed_temperature = 50 | |
| bridge_fan_speed = 40 | |
| compatible_printers = | |
| cooling = 0 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 20 | |
| filament_colour = #DEE0E6 | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 90 | |
| first_layer_temperature = 240 | |
| max_fan_speed = 5 | |
| min_fan_speed = 0 | |
| min_print_speed = 5 | |
| slowdown_below_layer_time = 15 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 250 | |
| [filament:Taulman T-Glase 1.75mm] | |
| bed_temperature = 79 | |
| bridge_fan_speed = 40 | |
| compatible_printers = | |
| cooling = 0 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 20 | |
| filament_colour = #FD0200 | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 90 | |
| first_layer_temperature = 240 | |
| max_fan_speed = 5 | |
| min_fan_speed = 0 | |
| min_print_speed = 5 | |
| slowdown_below_layer_time = 15 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 240 | |
| [filament:config-prusa-rough-ABS] | |
| bed_temperature = 100 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| cooling = 1 | |
| disable_fan_first_layers = 1 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 100 | |
| filament_colour = #FFFFFF | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 120 | |
| first_layer_temperature = 270 | |
| max_fan_speed = 100 | |
| min_fan_speed = 85 | |
| min_print_speed = 5 | |
| slowdown_below_layer_time = 20 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 256 | |
| [presets] | |
| filament = ColorFabb Brass Bronze 1.75mm | |
| print = 0.05mm PLA ULTRADETAIL | |
| printer = MY Prusa i3 1.75 | |
| [print:0.05mm PLA ULTRADETAIL] | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 8 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 0.1 | |
| bridge_speed = 20 | |
| brim_connections_width = 0 | |
| brim_width = 0 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 20 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.3 | |
| fill_angle = 45 | |
| fill_density = 15% | |
| fill_gaps = 1 | |
| fill_pattern = rectilinear | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.45 | |
| first_layer_height = 0.2 | |
| first_layer_speed = 80% | |
| gap_fill_speed = 0 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.5 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 4% | |
| infill_speed = 40 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.05 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 4 | |
| notes = | |
| only_retract_when_crossing_perimeters = 0 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 0 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 40 | |
| perimeters = 4 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = random | |
| shortcuts = support_material | |
| skirt_distance = 2 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 0 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.3 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 1.5 | |
| support_material_speed = 50 | |
| support_material_threshold = 60% | |
| thin_walls = 0 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 20 | |
| top_solid_layers = 10 | |
| travel_speed = 200 | |
| xy_size_compensation = 0 | |
| [print:0.10mm DETAIL] | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 8 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 0.1 | |
| bridge_speed = 25 | |
| brim_connections_width = 0 | |
| brim_width = 0 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 20 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 0 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.3 | |
| fill_angle = 45 | |
| fill_density = 10% | |
| fill_gaps = 1 | |
| fill_pattern = rectilinear | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0 | |
| first_layer_height = 0.15 | |
| first_layer_speed = 80% | |
| gap_fill_speed = 0 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.5 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 2% | |
| infill_speed = 60 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.1 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 4 | |
| notes = | |
| only_retract_when_crossing_perimeters = 0 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 0 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 40 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = nearest | |
| shortcuts = support_material | |
| skirt_distance = 2 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 0 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.3 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 1.5 | |
| support_material_speed = 50 | |
| support_material_threshold = 60% | |
| thin_walls = 0 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 25 | |
| top_solid_layers = 9 | |
| travel_speed = 100 | |
| xy_size_compensation = 0 | |
| [print:0.10mm DETAIL HEAVY] | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 8 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 0.1 | |
| bridge_speed = 25 | |
| brim_connections_width = 0 | |
| brim_width = 0 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 20 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 0 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.3 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0 | |
| first_layer_height = 0.15 | |
| first_layer_speed = 80% | |
| gap_fill_speed = 0 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.5 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 2% | |
| infill_speed = 60 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.1 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 4 | |
| notes = | |
| only_retract_when_crossing_perimeters = 0 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 0 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 40 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = nearest | |
| shortcuts = support_material | |
| skirt_distance = 2 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 0 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.3 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 1.5 | |
| support_material_speed = 50 | |
| support_material_threshold = 60% | |
| thin_walls = 0 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 25 | |
| top_solid_layers = 9 | |
| travel_speed = 100 | |
| xy_size_compensation = 0 | |
| [print:0.10mm DETAIL SUPPORT] | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 8 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 0.1 | |
| bridge_speed = 25 | |
| brim_connections_width = 0 | |
| brim_width = 0 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 20 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 0 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.3 | |
| fill_angle = 45 | |
| fill_density = 15% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0 | |
| first_layer_height = 0.15 | |
| first_layer_speed = 80% | |
| gap_fill_speed = 0 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.5 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 2% | |
| infill_speed = 60 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.1 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 4 | |
| notes = | |
| only_retract_when_crossing_perimeters = 0 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 0 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 40 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = nearest | |
| shortcuts = support_material | |
| skirt_distance = 2 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 0 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.3 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 1.5 | |
| support_material_speed = 50 | |
| support_material_threshold = 60% | |
| thin_walls = 0 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 25 | |
| top_solid_layers = 9 | |
| travel_speed = 100 | |
| xy_size_compensation = 0 | |
| [print:0.20mm FLEX] | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 5 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 0.65 | |
| bridge_speed = 15 | |
| brim_connections_width = 0 | |
| brim_width = 0 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 15 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 0 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.45 | |
| fill_angle = 45 | |
| fill_density = 22% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0 | |
| first_layer_height = 0.2 | |
| first_layer_speed = 100% | |
| gap_fill_speed = 15 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 0.25 | |
| infill_speed = 15 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.2 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 4 | |
| notes = | |
| only_retract_when_crossing_perimeters = 0 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 0 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 15 | |
| perimeters = 2 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = nearest | |
| shortcuts = support_material | |
| skirt_distance = 2 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 0 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 15 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.05 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 1 | |
| support_material_speed = 15 | |
| support_material_threshold = 40 | |
| thin_walls = 0 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 6 | |
| travel_speed = 100 | |
| xy_size_compensation = 0 | |
| [print:0.20mm HEAVY 10% walls PLA] | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 4 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 0.65 | |
| bridge_speed = 15 | |
| brim_connections_width = 0 | |
| brim_width = 0 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0.45 | |
| external_perimeter_speed = 40 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.45 | |
| fill_angle = 45 | |
| fill_density = 10% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.45 | |
| first_layer_height = 0.2 | |
| first_layer_speed = 70% | |
| gap_fill_speed = 40 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.45 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 0 | |
| infill_speed = 40 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.2 | |
| max_print_speed = 50 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 4 | |
| notes = | |
| only_retract_when_crossing_perimeters = 0 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 0 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.45 | |
| perimeter_speed = 40 | |
| perimeters = 5 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = nearest | |
| shortcuts = support_material | |
| skirt_distance = 2 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 40 | |
| solid_infill_below_area = 0 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.45 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.05 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 1 | |
| support_material_speed = 50 | |
| support_material_threshold = 40 | |
| thin_walls = 0 | |
| top_infill_extrusion_width = 0.45 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 20 | |
| top_solid_layers = 4 | |
| travel_speed = 100 | |
| xy_size_compensation = 0 | |
| [print:0.20mm NORMAL] | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 0.65 | |
| bridge_speed = 15 | |
| brim_connections_width = 0 | |
| brim_width = 0 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0.45 | |
| external_perimeter_speed = 40 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 0 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.45 | |
| fill_angle = 45 | |
| fill_density = 22% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.45 | |
| first_layer_height = 0.2 | |
| first_layer_speed = 70% | |
| gap_fill_speed = 40 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.45 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 0 | |
| infill_speed = 40 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.2 | |
| max_print_speed = 50 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 4 | |
| notes = | |
| only_retract_when_crossing_perimeters = 0 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 0 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.45 | |
| perimeter_speed = 40 | |
| perimeters = 2 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = nearest | |
| shortcuts = support_material | |
| skirt_distance = 2 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 40 | |
| solid_infill_below_area = 0 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.45 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.05 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 1 | |
| support_material_speed = 50 | |
| support_material_threshold = 40 | |
| thin_walls = 0 | |
| top_infill_extrusion_width = 0.45 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 20 | |
| top_solid_layers = 3 | |
| travel_speed = 100 | |
| xy_size_compensation = 0 | |
| [print:0.20mm NORMAL 5%] | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 0.65 | |
| bridge_speed = 15 | |
| brim_connections_width = 0 | |
| brim_width = 0 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0.45 | |
| external_perimeter_speed = 40 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 0 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.45 | |
| fill_angle = 45 | |
| fill_density = 5% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.45 | |
| first_layer_height = 0.2 | |
| first_layer_speed = 70% | |
| gap_fill_speed = 40 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.45 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 0 | |
| infill_speed = 40 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.2 | |
| max_print_speed = 50 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 4 | |
| notes = | |
| only_retract_when_crossing_perimeters = 0 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 0 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.45 | |
| perimeter_speed = 40 | |
| perimeters = 2 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = nearest | |
| shortcuts = support_material | |
| skirt_distance = 2 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 40 | |
| solid_infill_below_area = 0 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.45 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.05 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 1 | |
| support_material_speed = 50 | |
| support_material_threshold = 40 | |
| thin_walls = 0 | |
| top_infill_extrusion_width = 0.45 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 20 | |
| top_solid_layers = 3 | |
| travel_speed = 100 | |
| xy_size_compensation = 0 | |
| [print:0.20mm NORMAL 5% sup] | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 0.65 | |
| bridge_speed = 15 | |
| brim_connections_width = 0 | |
| brim_width = 0 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0.45 | |
| external_perimeter_speed = 40 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 0 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.45 | |
| fill_angle = 45 | |
| fill_density = 5% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.45 | |
| first_layer_height = 0.2 | |
| first_layer_speed = 70% | |
| gap_fill_speed = 40 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.45 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 0 | |
| infill_speed = 40 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.2 | |
| max_print_speed = 50 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 4 | |
| notes = | |
| only_retract_when_crossing_perimeters = 0 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 0 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.45 | |
| perimeter_speed = 40 | |
| perimeters = 2 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = nearest | |
| shortcuts = support_material | |
| skirt_distance = 2 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 40 | |
| solid_infill_below_area = 0 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.45 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.05 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 1 | |
| support_material_speed = 50 | |
| support_material_threshold = 40 | |
| thin_walls = 0 | |
| top_infill_extrusion_width = 0.45 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 20 | |
| top_solid_layers = 3 | |
| travel_speed = 100 | |
| xy_size_compensation = 0 | |
| [print:0.20mm NORMAL 5% sup heavy PLAS] | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 0.65 | |
| bridge_speed = 15 | |
| brim_connections_width = 0 | |
| brim_width = 0 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0.45 | |
| external_perimeter_speed = 40 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 0 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.45 | |
| fill_angle = 45 | |
| fill_density = 5% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.45 | |
| first_layer_height = 0.2 | |
| first_layer_speed = 70% | |
| gap_fill_speed = 40 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.45 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 0 | |
| infill_speed = 40 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.2 | |
| max_print_speed = 50 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 4 | |
| notes = | |
| only_retract_when_crossing_perimeters = 0 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 0 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.45 | |
| perimeter_speed = 40 | |
| perimeters = 5 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = nearest | |
| shortcuts = support_material | |
| skirt_distance = 2 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 40 | |
| solid_infill_below_area = 0 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.45 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.05 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 1 | |
| support_material_speed = 50 | |
| support_material_threshold = 40 | |
| thin_walls = 0 | |
| top_infill_extrusion_width = 0.45 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 20 | |
| top_solid_layers = 3 | |
| travel_speed = 100 | |
| xy_size_compensation = 0 | |
| [print:0.20mm NORMAL 5% walls] | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 4 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 0.65 | |
| bridge_speed = 15 | |
| brim_connections_width = 0 | |
| brim_width = 0 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0.45 | |
| external_perimeter_speed = 40 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 0 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.45 | |
| fill_angle = 45 | |
| fill_density = 5% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.45 | |
| first_layer_height = 0.2 | |
| first_layer_speed = 70% | |
| gap_fill_speed = 40 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.45 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 0 | |
| infill_speed = 40 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.2 | |
| max_print_speed = 50 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 4 | |
| notes = | |
| only_retract_when_crossing_perimeters = 0 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 0 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.45 | |
| perimeter_speed = 40 | |
| perimeters = 4 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = nearest | |
| shortcuts = support_material | |
| skirt_distance = 2 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 40 | |
| solid_infill_below_area = 0 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.45 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.05 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 1 | |
| support_material_speed = 50 | |
| support_material_threshold = 40 | |
| thin_walls = 0 | |
| top_infill_extrusion_width = 0.45 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 20 | |
| top_solid_layers = 4 | |
| travel_speed = 100 | |
| xy_size_compensation = 0 | |
| [print:0.25mm DRAFT] | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 4 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 0.65 | |
| bridge_speed = 15 | |
| brim_connections_width = 0 | |
| brim_width = 0 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 40 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 0 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.65 | |
| fill_angle = 45 | |
| fill_density = 22% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0 | |
| first_layer_height = 0.25 | |
| first_layer_speed = 50% | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 0.1 | |
| infill_speed = 55 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.25 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 4 | |
| notes = | |
| only_retract_when_crossing_perimeters = 0 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 0 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 40 | |
| perimeters = 2 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = nearest | |
| shortcuts = support_material | |
| skirt_distance = 2 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 40 | |
| solid_infill_below_area = 0 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.1 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.6 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 1 | |
| support_material_speed = 50 | |
| support_material_threshold = 43 | |
| thin_walls = 0 | |
| top_infill_extrusion_width = 0.75 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 20 | |
| top_solid_layers = 5 | |
| travel_speed = 100 | |
| xy_size_compensation = 0 | |
| [print:MY 0.10mm DETAIL] | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 8 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 0.1 | |
| bridge_speed = 25 | |
| brim_connections_width = 0 | |
| brim_width = 0 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 20 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 0 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.3 | |
| fill_angle = 45 | |
| fill_density = 10% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0 | |
| first_layer_height = 0.15 | |
| first_layer_speed = 80% | |
| gap_fill_speed = 0 | |
| gcode_comments = 1 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.5 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 2% | |
| infill_speed = 60 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.1 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 4 | |
| notes = Bla bla bla | |
| only_retract_when_crossing_perimeters = 0 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 0 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 40 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = nearest | |
| shortcuts = support_material | |
| skirt_distance = 2 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 0 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.3 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 1.5 | |
| support_material_speed = 50 | |
| support_material_threshold = 60% | |
| thin_walls = 0 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 25 | |
| top_solid_layers = 9 | |
| travel_speed = 100 | |
| xy_size_compensation = 0 | |
| [print:config-prusa-rough-ABS] | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 9 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 0.1 | |
| bridge_speed = 25 | |
| brim_connections_width = 0 | |
| brim_width = 0 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 20 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 0 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 60% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0 | |
| first_layer_height = 0.25 | |
| first_layer_speed = 30% | |
| gap_fill_speed = 0 | |
| gcode_comments = 1 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 2% | |
| infill_speed = 40 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.2 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 4 | |
| notes = Bla bla bla | |
| only_retract_when_crossing_perimeters = 0 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 0 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 20 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = nearest | |
| shortcuts = support_material | |
| skirt_distance = 2 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 10 | |
| solid_infill_below_area = 0 | |
| solid_infill_every_layers = 10 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.3 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 1.5 | |
| support_material_speed = 50 | |
| support_material_threshold = 60% | |
| thin_walls = 0 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 25 | |
| top_solid_layers = 8 | |
| travel_speed = 140 | |
| xy_size_compensation = 0 | |
| [printer:MY Prusa i3 1.75] | |
| bed_shape = 200.01x-0.00091,200.012x0.005409,200.01x0.006186,200.01x199.994,200.012x199.995,200.01x200.001,200.011x200.017,200.01x200.016,199.998x200.01,199.991x200.01,199.99x200.01,189.99x200.01,189.99x195.01,170.01x195.01,170.01x199.99,170.01x199.99,170.01x200,170.01x200.01,170x200.01,29.99x200.01,29.99x195.01,10.01x195.01,10.01x200.01,0.009509x200.01,0.009496x200.01,0.002241x200.01,-0.010875x200.017,-0.010069x200.001,-0.011561x199.995,-0.01001x199.994,-0.01001x0.006186,-0.011561x0.005409,-0.010069x-0.00091,-0.010875x-0.016628,0.002241x-0.01007,0.009496x-0.010256,0.009509x-0.01001,10.01x-0.01001,10.01x4.98999,29.99x4.98999,29.99x-0.01001,170x-0.01001,170.01x-0.010373,170.01x-8.9e-005,170.01x0.009652,170.01x0.009658,170.01x4.98999,189.99x4.98999,189.99x-0.01001,199.99x-0.01001,199.991x-0.010256,199.998x-0.01007,200.01x-0.016188,200.011x-0.016628 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| end_gcode = M104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nM84 ; disable motors | |
| extruder_offset = 0x0 | |
| gcode_flavor = reprap | |
| has_heatbed = 1 | |
| host_type = octoprint | |
| layer_gcode = | |
| nozzle_diameter = 0.4 | |
| octoprint_apikey = | |
| pressure_advance = 0.035 | |
| print_host = | |
| printer_notes = | |
| printer_settings_id = | |
| retract_before_travel = 1 | |
| retract_layer_change = 1 | |
| retract_length = 1.5 | |
| retract_length_toolchange = 3 | |
| retract_lift = 0 | |
| retract_lift_above = 0 | |
| retract_lift_below = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 30 | |
| serial_port = | |
| serial_speed = 250000 | |
| start_gcode = M201 X1000 Y1000 E600\nM109 S[first_layer_temperature]\nM92 E161.3\nG28\nG92 E0.0\nG1 X8.0 F2000\nG1 Y60.0 E4.0 F1000.0\nG1 Y100.0 E8.5 F1000.0\nG92 E0.0 | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 1 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0 | |
| z_offset = 0 | |
| z_steps_per_mm = 0 | |
| [printer:Prusa i3 1.75] | |
| bed_shape = 200.01x-0.00091,200.012x0.005409,200.01x0.006186,200.01x199.994,200.012x199.995,200.01x200.001,200.011x200.017,200.01x200.016,199.998x200.01,199.991x200.01,199.99x200.01,189.99x200.01,189.99x195.01,170.01x195.01,170.01x199.99,170.01x199.99,170.01x200,170.01x200.01,170x200.01,29.99x200.01,29.99x195.01,10.01x195.01,10.01x200.01,0.009509x200.01,0.009496x200.01,0.002241x200.01,-0.010875x200.017,-0.010069x200.001,-0.011561x199.995,-0.01001x199.994,-0.01001x0.006186,-0.011561x0.005409,-0.010069x-0.00091,-0.010875x-0.016628,0.002241x-0.01007,0.009496x-0.010256,0.009509x-0.01001,10.01x-0.01001,10.01x4.98999,29.99x4.98999,29.99x-0.01001,170x-0.01001,170.01x-0.010373,170.01x-8.9e-005,170.01x0.009652,170.01x0.009658,170.01x4.98999,189.99x4.98999,189.99x-0.01001,199.99x-0.01001,199.991x-0.010256,199.998x-0.01007,200.01x-0.016188,200.011x-0.016628 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| end_gcode = M104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nM84 ; disable motors | |
| extruder_offset = 0x0 | |
| gcode_flavor = reprap | |
| has_heatbed = 1 | |
| host_type = octoprint | |
| layer_gcode = | |
| nozzle_diameter = 0.4 | |
| octoprint_apikey = | |
| pressure_advance = 0.035 | |
| print_host = | |
| printer_notes = | |
| printer_settings_id = | |
| retract_before_travel = 1 | |
| retract_layer_change = 1 | |
| retract_length = 1.5 | |
| retract_length_toolchange = 3 | |
| retract_lift = 0 | |
| retract_lift_above = 0 | |
| retract_lift_below = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 30 | |
| serial_port = | |
| serial_speed = 250000 | |
| start_gcode = M201 X1000 Y1000 E600\nM109 S[first_layer_temperature]\nM92 E161.3\nG28\nG92 E0.0\nG1 X8.0 F2000\nG1 Y60.0 E4.0 F1000.0\nG1 Y100.0 E8.5 F1000.0\nG92 E0.0 | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 1 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0 | |
| z_offset = 0 | |
| z_steps_per_mm = 0 | |
| [printer:Prusa i3 1.75 FLEX] | |
| bed_shape = 200.01x-0.00091,200.012x0.005409,200.01x0.006186,200.01x199.994,200.012x199.995,200.01x200.001,200.011x200.017,200.01x200.016,199.998x200.01,199.991x200.01,199.99x200.01,189.99x200.01,189.99x195.01,170.01x195.01,170.01x199.99,170.01x199.99,170.01x200,170.01x200.01,170x200.01,29.99x200.01,29.99x195.01,10.01x195.01,10.01x200.01,0.009509x200.01,0.009496x200.01,0.002241x200.01,-0.010875x200.017,-0.010069x200.001,-0.011561x199.995,-0.01001x199.994,-0.01001x0.006186,-0.011561x0.005409,-0.010069x-0.00091,-0.010875x-0.016628,0.002241x-0.01007,0.009496x-0.010256,0.009509x-0.01001,10.01x-0.01001,10.01x4.98999,29.99x4.98999,29.99x-0.01001,170x-0.01001,170.01x-0.010373,170.01x-8.9e-005,170.01x0.009652,170.01x0.009658,170.01x4.98999,189.99x4.98999,189.99x-0.01001,199.99x-0.01001,199.991x-0.010256,199.998x-0.01007,200.01x-0.016188,200.011x-0.016628 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| end_gcode = M104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nM84 ; disable motors | |
| extruder_offset = 0x0 | |
| gcode_flavor = reprap | |
| has_heatbed = 1 | |
| host_type = octoprint | |
| layer_gcode = | |
| nozzle_diameter = 0.4 | |
| octoprint_apikey = | |
| pressure_advance = 0.035 | |
| print_host = | |
| printer_notes = | |
| printer_settings_id = | |
| retract_before_travel = 1 | |
| retract_layer_change = 1 | |
| retract_length = 1.5 | |
| retract_length_toolchange = 3 | |
| retract_lift = 0 | |
| retract_lift_above = 0 | |
| retract_lift_below = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 30 | |
| serial_port = | |
| serial_speed = 250000 | |
| start_gcode = M201 X1000 Y1000 E80\nM109 S[first_layer_temperature]\nM92 E161.3\nG28\nG92 E0.0\nG1 X8.0 F2000\nG1 Y60.0 E4.0 F1000.0\nG1 Y100.0 E8.5 F1000.0\nG92 E0.0 | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 1 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0 | |
| z_offset = 0 | |
| z_steps_per_mm = 0 | |
| [printer:config-prusa-rough-ABS] | |
| bed_shape = 200.01x-0.00091,200.012x0.005409,200.01x0.006186,200.01x199.994,200.012x199.995,200.01x200.001,200.011x200.017,200.01x200.016,199.998x200.01,199.991x200.01,199.99x200.01,189.99x200.01,189.99x195.01,170.01x195.01,170.01x199.99,170.01x199.99,170.01x200,170.01x200.01,170x200.01,29.99x200.01,29.99x195.01,10.01x195.01,10.01x200.01,0.009509x200.01,0.009496x200.01,0.002241x200.01,-0.010875x200.017,-0.010069x200.001,-0.011561x199.995,-0.01001x199.994,-0.01001x0.006186,-0.011561x0.005409,-0.010069x-0.00091,-0.010875x-0.016628,0.002241x-0.01007,0.009496x-0.010256,0.009509x-0.01001,10.01x-0.01001,10.01x4.98999,29.99x4.98999,29.99x-0.01001,170x-0.01001,170.01x-0.010373,170.01x-8.9e-005,170.01x0.009652,170.01x0.009658,170.01x4.98999,189.99x4.98999,189.99x-0.01001,199.99x-0.01001,199.991x-0.010256,199.998x-0.01007,200.01x-0.016188,200.011x-0.016628 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| end_gcode = M104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nM84 ; disable motors | |
| extruder_offset = 0x0 | |
| gcode_flavor = reprap | |
| has_heatbed = 1 | |
| host_type = octoprint | |
| layer_gcode = | |
| nozzle_diameter = 0.4 | |
| octoprint_apikey = | |
| pressure_advance = 0.035 | |
| print_host = | |
| printer_notes = | |
| printer_settings_id = | |
| retract_before_travel = 1 | |
| retract_layer_change = 1 | |
| retract_length = 1.5 | |
| retract_length_toolchange = 3 | |
| retract_lift = 0 | |
| retract_lift_above = 0 | |
| retract_lift_below = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 50 | |
| serial_port = | |
| serial_speed = 250000 | |
| start_gcode = M201 X1000 Y1000 E600\nM109 S[first_layer_temperature]\nM92 E161.3\nG28\nG92 E0.0\nG1 X8.0 F2000\nG1 Y60.0 E4.0 F1000.0\nG1 Y100.0 E8.5 F1000.0\nG92 E0.0 | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 1 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0 | |
| z_offset = 0 | |
| z_steps_per_mm = 0 | |
| [settings] | |
| autocenter = 1 |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment