Booting RancherOS v0.4.3 on a Raspberry Pi 2

UART console boot log

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0xf00
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.1.17-v7+ (dc4@dc4-XPS13-9333) (gcc version 4.8.3 20140303 (prerelease) (crosstool-NG linaro-1.13.1+bzr2650 - Linaro GCC 2014.03) ) #838 SMP Tue Feb 9 13:15:09 GMT 2016
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Raspberry Pi 2 Model B Rev 1.1
[    0.000000] cma: Reserved 8 MiB at 0x3a400000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] [bcm2709_smp_init_cpus] enter (9420->f3003010)
[    0.000000] [bcm2709_smp_init_cpus] ncores=4
[    0.000000] PERCPU: Embedded 12 pages/cpu @bafb1000 s20416 r8192 d20544 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 239540
[    0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2709.boardrev=0xa01041 bcm2709.serial=0x3431152a smsc95xx.macaddr=B8:27:EB:31:15:2A bcm2708_fb.fbswap=1 bcm2709.uart_clock=3000000 bcm2709.disk_led_gpio=47 bcm2709.disk_led_active_low=0 sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  +dwc_otg.lpm_enable=0 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 cgroup-enable=memory swapaccount=1 elevator=deadline rootwait console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 console=tty0 rancher.password=rancher rw init=/init
[    0.000000] Enabling memory control group subsystem
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 939508K/966656K available (5944K kernel code, 534K rwdata, 1660K rodata, 440K init, 757K bss, 18956K reserved, 8192K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xbb800000 - 0xff000000   (1080 MB)
[    0.000000]     lowmem  : 0x80000000 - 0xbb000000   ( 944 MB)
[    0.000000]     modules : 0x7f000000 - 0x80000000   (  16 MB)
[    0.000000]       .text : 0x80008000 - 0x807753c4   (7605 kB)
[    0.000000]       .init : 0x80776000 - 0x807e4000   ( 440 kB)
[    0.000000]       .data : 0x807e4000 - 0x80869a68   ( 535 kB)
[    0.000000]        .bss : 0x8086c000 - 0x8092975c   ( 758 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000] NR_IRQS:608
[    0.000000] Architected cp15 timer(s) running at 19.20MHz (phys).
[    0.000000] clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000011] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000033] Switching to timer-based delay loop, resolution 52ns
[    0.000312] Console: colour dummy device 80x30
[    0.001565] console [tty1] enabled
[    0.001624] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.001699] pid_max: default: 32768 minimum: 301
[    0.002071] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.002125] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.003413] Initializing cgroup subsys blkio
[    0.003485] Initializing cgroup subsys memory
[    0.003574] Initializing cgroup subsys devices
[    0.003625] Initializing cgroup subsys freezer
[    0.003690] Initializing cgroup subsys net_cls
[    0.003789] CPU: Testing write buffer coherency: ok
[    0.003901] ftrace: allocating 20289 entries in 60 pages
[    0.054369] CPU0: update cpu_capacity 1024
[    0.054447] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00
[    0.054487] [bcm2709_smp_prepare_cpus] enter
[    0.054639] Setting up static identity map for 0x8240 - 0x8274
[    0.057198] [bcm2709_boot_secondary] cpu:1 started (0) 18
[    0.057642] [bcm2709_secondary_init] enter cpu:1
[    0.057698] CPU1: update cpu_capacity 1024
[    0.057707] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
[    0.058287] [bcm2709_boot_secondary] cpu:2 started (0) 18
[    0.058646] [bcm2709_secondary_init] enter cpu:2
[    0.058680] CPU2: update cpu_capacity 1024
[    0.058689] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
[    0.059225] [bcm2709_boot_secondary] cpu:3 started (0) 17
[    0.059481] [bcm2709_secondary_init] enter cpu:3
[    0.059510] CPU3: update cpu_capacity 1024
[    0.059518] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
[    0.059609] Brought up 4 CPUs
[    0.059721] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[    0.059755] CPU: All CPU(s) started in HYP mode.
[    0.059784] CPU: Virtualization extensions available.
[    0.060764] devtmpfs: initialized
[    0.085129] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.085505] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.086674] pinctrl core: initialized pinctrl subsystem
[    0.087509] NET: Registered protocol family 16
[    0.093400] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[    0.094935] bcm2709.uart_clock = 3000000
[    0.100209] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.100270] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.100499] Serial: AMBA PL011 UART driver
[    0.100710] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 83, base_baud = 0) is a PL011 rev2
[    0.620733] console [ttyAMA0] enabled
[    0.625012] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[    0.699677] bcm2708-dmaengine 3f007000.dma: DMA legacy API manager at f3007000, dmachans=0xf35
[    0.708414] bcm2708-dmaengine 3f007000.dma: Initialized 7 DMA channels (+ 1 legacy)
[    0.716823] bcm2708-dmaengine 3f007000.dma: Load BCM2835 DMA engine driver
[    0.723739] bcm2708-dmaengine 3f007000.dma: dma_debug:0
[    0.729705] SCSI subsystem initialized
[    0.733715] usbcore: registered new interface driver usbfs
[    0.739341] usbcore: registered new interface driver hub
[    0.744806] usbcore: registered new device driver usb
[    0.750576] raspberrypi-firmware soc:firmware: Attached to firmware from 2016-02-01 17:51
[    0.786354] Switched to clocksource arch_sys_counter
[    0.838618] FS-Cache: Loaded
[    0.841901] CacheFiles: Loaded
[    0.856260] NET: Registered protocol family 2
[    0.861958] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.869209] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.875861] TCP: Hash tables configured (established 8192 bind 8192)
[    0.882400] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.888422] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.895267] NET: Registered protocol family 1
[    0.900110] RPC: Registered named UNIX socket transport module.
[    0.906050] RPC: Registered udp transport module.
[    0.910810] RPC: Registered tcp transport module.
[    0.915529] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.923364] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.932964] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.955447] VFS: Disk quotas dquot_6.6.0
[    0.959816] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.969397] FS-Cache: Netfs 'nfs' registered for caching
[    0.975872] NFS: Registering the id_resolver key type
[    0.981040] Key type id_resolver registered
[    0.985240] Key type id_legacy registered
[    0.991972] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.999639] io scheduler noop registered
[    1.003593] io scheduler deadline registered (default)
[    1.009105] io scheduler cfq registered
[    1.015439] BCM2708FB: allocated DMA memory fa800000
[    1.020539] BCM2708FB: allocated DMA channel 0 @ f3007000
[    1.031566] Console: switching to colour frame buffer device 82x26
[    1.043018] Serial: 8250/16550 driver, 0 ports, IRQ sharing disabled
[    1.051625] KGDB: Registered I/O driver kgdboc
[    1.087112] vc-cma: Videocore CMA driver
[    1.092710] vc-cma: vc_cma_base      = 0x00000000
[    1.099061] vc-cma: vc_cma_size      = 0x00000000 (0 MiB)
[    1.106011] vc-cma: vc_cma_initial   = 0x00000000 (0 MiB)
[    1.113135] vc-mem: phys_addr:0x00000000 mem_base=0x3dc00000 mem_size:0x3f000000(1008 MiB)
[    1.140070] brd: module loaded
[    1.153475] loop: module loaded
[    1.159141] vchiq: vchiq_init_state: slot_zero = 0xba880000, is_master = 0
[    1.169368] Loading iSCSI transport class v2.0-870.
[    1.176796] usbcore: registered new interface driver smsc95xx
[    1.184116] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.391737] Core Release: 2.80a
[    1.396400] Setting default values for core params
[    1.402697] Finished setting default values for core params
[    1.610242] Using Buffer DMA mode
[    1.615050] Periodic Transfer Interrupt Enhancement - disabled
[    1.622462] Multiprocessor Interrupt Enhancement - disabled
[    1.629603] OTG VER PARAM: 0, OTG VER FLAG: 0
[    1.635492] Dedicated Tx FIFOs mode
[    1.640842] WARN::dwc_otg_hcd_init:1047: FIQ DMA bounce buffers: virt = 0xba814000 dma = 0xfa814000 len=9024
[    1.653870] FIQ FSM acceleration enabled for :
[    1.653870] Non-periodic Split Transactions
[    1.653870] Periodic Split Transactions
[    1.653870] High-Speed Isochronous Endpoints
[    1.677074] WARN::hcd_init_fiq:412: FIQ on core 1 at 0x803fcf78
[    1.684609] WARN::hcd_init_fiq:413: FIQ ASM at 0x803fd2d4 length 36
[    1.692501] WARN::hcd_init_fiq:438: MPHI regs_base at 0xbb89a000
[    1.700121] dwc_otg 3f980000.usb: DWC OTG Controller
[    1.706707] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[    1.715634] dwc_otg 3f980000.usb: irq 32, io mem 0x00000000
[    1.722827] Init: Port Power? op_state=1
[    1.728298] Init: Power Port (0)
[    1.733301] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.741689] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.750495] usb usb1: Product: DWC OTG Controller
[    1.756753] usb usb1: Manufacturer: Linux 4.1.17-v7+ dwc_otg_hcd
[    1.764299] usb usb1: SerialNumber: 3f980000.usb
[    1.771335] hub 1-0:1.0: USB hub found
[    1.776733] hub 1-0:1.0: 1 port detected
[    1.783015] usbcore: registered new interface driver usb-storage
[    1.790772] mousedev: PS/2 mouse device common for all mice
[    1.798651] bcm2835-cpufreq: min=600000 max=900000
[    1.805236] sdhci: Secure Digital Host Controller Interface driver
[    1.812959] sdhci: Copyright(c) Pierre Ossman
[    1.819322] mmc-bcm2835 3f300000.mmc: mmc_debug:0 mmc_debug2:0
[    1.826736] mmc-bcm2835 3f300000.mmc: DMA channels allocated
[    1.866714] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.878964] ledtrig-cpu: registered to indicate activity on CPUs
[    1.886845] hidraw: raw HID events driver (C) Jiri Kosina
[    1.894114] usbcore: registered new interface driver usbhid
[    1.901305] usbhid: USB HID core driver
[    1.907257] Initializing XFRM netlink socket
[    1.914188] NET: Registered protocol family 17
[    1.920402] Key type dns_resolver registered
[    1.926904] Registering SWP/SWPB emulation handler
[    1.934067] registered taskstats version 1
[    1.939919] vc-sm: Videocore shared memory driver
[    1.946092] [vc_sm_connected_init]: start
[    1.952304] [vc_sm_connected_init]: end - returning 0
[    1.960436] Waiting for root device /dev/mmcblk0p2...
[    1.976022] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.976510] Indeed it is in host mode hprt0 = 00021501
[    1.996986] mmc0: new high speed SDHC card at address aaaa
[    2.004671] mmcblk0: mmc0:aaaa SL32G 29.7 GiB
[    2.012376]  mmcblk0: p1 p2
[    2.135407] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)
[    2.146121] VFS: Mounted root (ext4 filesystem) on device 179:2.
[    2.156287] devtmpfs: error mounting -2
[    2.156410] usb 1-1: new high-speed USB device number 2 using dwc_otg
[    2.161874] Indeed it is in host mode hprt0 = 00001101
[    2.177477] Freeing unused kernel memory: 440K (80776000 - 807e4000)
[    2.356801] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[    2.365349] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.375309] hub 1-1:1.0: USB hub found
[    2.381001] hub 1-1:1.0: 5 ports detected
[    2.666421] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[    2.707568] NET: Registered protocol family 10
[    2.776830] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[    2.785657] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.797906] smsc95xx v1.0.4
[    2.861047] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:31:15:2a
[    4.946560] random: ros urandom read with 83 bits of entropy available
[    5.117516] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    8.441433] Bridge firewalling registered
[    9.205793] nf_conntrack version 0.5.0 (14814 buckets, 59256 max)
[    9.278201] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.061406] cgroup: docker (78) created nested cgroup for controller "memory" which has incomplete hierarchy support. Nested cgroups may change behavior in the future.
[   12.081035] cgroup: "memory" requires setting use_hierarchy to 1 on the root
[   12.926024] random: nonblocking pool is initialized
[   13.699798] udevd[11]: starting version 3.1.2
[   13.769298] device veth7db947b entered promiscuous mode
[   13.777950] IPv6: ADDRCONF(NETDEV_UP): veth7db947b: link is not ready
[   14.999340] bcm2835-rng 3f104000.rng: hwrng registered
[   15.006810] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[   15.020358] eth0: renamed from veth8e490f0
[   15.060419] IPv6: ADDRCONF(NETDEV_CHANGE): veth7db947b: link becomes ready
[   15.069494] docker-sys: port 1(veth7db947b) entered forwarding state
[   15.077751] docker-sys: port 1(veth7db947b) entered forwarding state
[   15.356756] IPv6: eth0: IPv6 duplicate address fe80::42:acff:fe12:1 detected!
[   15.502003] veth8e490f0: renamed from eth0
[   15.629976] docker-sys: port 1(veth7db947b) entered disabled state
[   15.668373] docker-sys: port 1(veth7db947b) entered disabled state
[   15.685298] device veth7db947b left promiscuous mode
[   15.692041] docker-sys: port 1(veth7db947b) entered disabled state
[   16.217292] udevd[1]: starting version 3.1.2
[   17.506382] 9pnet: Installing 9P2000 support
[   17.522588] 9p: Installing v9fs 9p2000 file system support
[   17.530898] 9pnet: Could not find request transport: virtio
[   20.557962] device vethedeca90 entered promiscuous mode
[   20.566694] IPv6: ADDRCONF(NETDEV_UP): vethedeca90: link is not ready
[   20.889093] eth0: renamed from veth99da6cc
[   20.960309] IPv6: ADDRCONF(NETDEV_CHANGE): vethedeca90: link becomes ready
[   20.969154] docker-sys: port 1(vethedeca90) entered forwarding state
[   20.977233] docker-sys: port 1(vethedeca90) entered forwarding state
[   21.426739] IPv6: eth0: IPv6 duplicate address fe80::42:acff:fe12:1 detected!
[   22.111979] cfg80211: Calling CRDA to update world regulatory domain
[   22.389095] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[   22.398073] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   23.920857] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   23.930044] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1
[   25.266679] cfg80211: Calling CRDA to update world regulatory domain
[   25.319044] docker-sys: port 1(vethedeca90) entered disabled state
[   25.328082] veth99da6cc: renamed from eth0
[   25.448617] docker-sys: port 1(vethedeca90) entered disabled state
[   25.465166] device vethedeca90 left promiscuous mode
[   25.472269] docker-sys: port 1(vethedeca90) entered disabled state
[   26.856397] 9pnet: Could not find request transport: virtio
[   28.416459] cfg80211: Calling CRDA to update world regulatory domain
[   31.576495] cfg80211: Calling CRDA to update world regulatory domain
[   31.887081] device vethf08a360 entered promiscuous mode
[   31.896697] IPv6: ADDRCONF(NETDEV_UP): vethf08a360: link is not ready
[   32.159289] eth0: renamed from veth53577bb
[   32.210566] IPv6: ADDRCONF(NETDEV_CHANGE): vethf08a360: link becomes ready
[   32.219567] docker-sys: port 1(vethf08a360) entered forwarding state
[   32.227756] docker-sys: port 1(vethf08a360) entered forwarding state
[   32.576836] IPv6: eth0: IPv6 duplicate address fe80::42:acff:fe12:1 detected!
[   33.739947] docker-sys: port 1(vethf08a360) entered disabled state
[   33.748803] veth53577bb: renamed from eth0
[   33.891135] docker-sys: port 1(vethf08a360) entered disabled state
[   33.908435] device vethf08a360 left promiscuous mode
[   33.915017] docker-sys: port 1(vethf08a360) entered disabled state
[   34.726481] cfg80211: Calling CRDA to update world regulatory domain
[   37.876484] cfg80211: Calling CRDA to update world regulatory domain
[   41.026485] cfg80211: Calling CRDA to update world regulatory domain
[   44.176437] cfg80211: Calling CRDA to update world regulatory domain
[   47.326489] cfg80211: Calling CRDA to update world regulatory domain
[   50.476468] cfg80211: Calling CRDA to update world regulatory domain
[   53.626470] cfg80211: Calling CRDA to update world regulatory domain
[   56.776475] cfg80211: Exceeded CRDA call max attempts. Not calling CRDA
[   64.597588] IPv6: ADDRCONF(NETDEV_UP): docker0: link is not ready
Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0xf00
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.1.17-v7+ (dc4@dc4-XPS13-9333) (gcc version 4.8.3 20140303 (prerelease) (crosstool-NG linaro-1.13.1+bzr2650 - Linaro GCC 2014.03) ) #838 SMP Tue Feb 9 13:15:09 GMT 2016
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Raspberry Pi 2 Model B Rev 1.1
[    0.000000] cma: Reserved 8 MiB at 0x3a400000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] [bcm2709_smp_init_cpus] enter (9420->f3003010)
[    0.000000] [bcm2709_smp_init_cpus] ncores=4
[    0.000000] PERCPU: Embedded 12 pages/cpu @bafb1000 s20416 r8192 d20544 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 239540
[    0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2709.boardrev=0xa01041 bcm2709.serial=0x3431152a smsc95xx.macaddr=B8:27:EB:31:15:2A bcm2708_fb.fbswap=1 bcm2709.uart_clock=3000000 bcm2709.disk_led_gpio=47 bcm2709.disk_led_active_low=0 sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  +dwc_otg.lpm_enable=0 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 cgroup-enable=memory swapaccount=1 elevator=deadline rootwait console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 console=tty0 rancher.password=rancher rw init=/init
[    0.000000] Enabling memory control group subsystem
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 939508K/966656K available (5944K kernel code, 534K rwdata, 1660K rodata, 440K init, 757K bss, 18956K reserved, 8192K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xbb800000 - 0xff000000   (1080 MB)
[    0.000000]     lowmem  : 0x80000000 - 0xbb000000   ( 944 MB)
[    0.000000]     modules : 0x7f000000 - 0x80000000   (  16 MB)
[    0.000000]       .text : 0x80008000 - 0x807753c4   (7605 kB)
[    0.000000]       .init : 0x80776000 - 0x807e4000   ( 440 kB)
[    0.000000]       .data : 0x807e4000 - 0x80869a68   ( 535 kB)
[    0.000000]        .bss : 0x8086c000 - 0x8092975c   ( 758 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000] NR_IRQS:608
[    0.000000] Architected cp15 timer(s) running at 19.20MHz (phys).
[    0.000000] clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000011] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000032] Switching to timer-based delay loop, resolution 52ns
[    0.000320] Console: colour dummy device 80x30
[    0.001578] console [tty1] enabled
[    0.001637] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.001713] pid_max: default: 32768 minimum: 301
[    0.002079] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.002133] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.003432] Initializing cgroup subsys blkio
[    0.003505] Initializing cgroup subsys memory
[    0.003599] Initializing cgroup subsys devices
[    0.003655] Initializing cgroup subsys freezer
[    0.003720] Initializing cgroup subsys net_cls
[    0.003824] CPU: Testing write buffer coherency: ok
[    0.003932] ftrace: allocating 20289 entries in 60 pages
[    0.054201] CPU0: update cpu_capacity 1024
[    0.054275] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00
[    0.054313] [bcm2709_smp_prepare_cpus] enter
[    0.054463] Setting up static identity map for 0x8240 - 0x8274
[    0.056984] [bcm2709_boot_secondary] cpu:1 started (0) 18
[    0.057426] [bcm2709_secondary_init] enter cpu:1
[    0.057483] CPU1: update cpu_capacity 1024
[    0.057492] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
[    0.058060] [bcm2709_boot_secondary] cpu:2 started (0) 17
[    0.058416] [bcm2709_secondary_init] enter cpu:2
[    0.058447] CPU2: update cpu_capacity 1024
[    0.058455] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
[    0.058998] [bcm2709_boot_secondary] cpu:3 started (0) 18
[    0.059254] [bcm2709_secondary_init] enter cpu:3
[    0.059282] CPU3: update cpu_capacity 1024
[    0.059291] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
[    0.059378] Brought up 4 CPUs
[    0.059490] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[    0.059524] CPU: All CPU(s) started in HYP mode.
[    0.059553] CPU: Virtualization extensions available.
[    0.060544] devtmpfs: initialized
[    0.084909] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.085284] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.086429] pinctrl core: initialized pinctrl subsystem
[    0.087268] NET: Registered protocol family 16
[    0.093186] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[    0.094714] bcm2709.uart_clock = 3000000
[    0.100020] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.100080] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.100306] Serial: AMBA PL011 UART driver
[    0.100516] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 83, base_baud = 0) is a PL011 rev2
[    0.620539] console [ttyAMA0] enabled
[    0.624815] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[    0.699441] bcm2708-dmaengine 3f007000.dma: DMA legacy API manager at f3007000, dmachans=0xf35
[    0.708175] bcm2708-dmaengine 3f007000.dma: Initialized 7 DMA channels (+ 1 legacy)
[    0.716577] bcm2708-dmaengine 3f007000.dma: Load BCM2835 DMA engine driver
[    0.723491] bcm2708-dmaengine 3f007000.dma: dma_debug:0
[    0.729455] SCSI subsystem initialized
[    0.733464] usbcore: registered new interface driver usbfs
[    0.739085] usbcore: registered new interface driver hub
[    0.744546] usbcore: registered new device driver usb
[    0.750323] raspberrypi-firmware soc:firmware: Attached to firmware from 2016-02-01 17:51
[    0.786089] Switched to clocksource arch_sys_counter
[    0.838347] FS-Cache: Loaded
[    0.841638] CacheFiles: Loaded
[    0.855972] NET: Registered protocol family 2
[    0.861671] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.868923] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.875576] TCP: Hash tables configured (established 8192 bind 8192)
[    0.882113] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.888131] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.894978] NET: Registered protocol family 1
[    0.899808] RPC: Registered named UNIX socket transport module.
[    0.905750] RPC: Registered udp transport module.
[    0.910507] RPC: Registered tcp transport module.
[    0.915227] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.923056] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.932654] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.955126] VFS: Disk quotas dquot_6.6.0
[    0.959496] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.969080] FS-Cache: Netfs 'nfs' registered for caching
[    0.975544] NFS: Registering the id_resolver key type
[    0.980750] Key type id_resolver registered
[    0.984951] Key type id_legacy registered
[    0.991672] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.999335] io scheduler noop registered
[    1.003288] io scheduler deadline registered (default)
[    1.008797] io scheduler cfq registered
[    1.015135] BCM2708FB: allocated DMA memory fa800000
[    1.020236] BCM2708FB: allocated DMA channel 0 @ f3007000
[    1.031262] Console: switching to colour frame buffer device 82x26
[    1.042730] Serial: 8250/16550 driver, 0 ports, IRQ sharing disabled
[    1.051343] KGDB: Registered I/O driver kgdboc
[    1.086853] vc-cma: Videocore CMA driver
[    1.092453] vc-cma: vc_cma_base      = 0x00000000
[    1.098804] vc-cma: vc_cma_size      = 0x00000000 (0 MiB)
[    1.105752] vc-cma: vc_cma_initial   = 0x00000000 (0 MiB)
[    1.112886] vc-mem: phys_addr:0x00000000 mem_base=0x3dc00000 mem_size:0x3f000000(1008 MiB)
[    1.139773] brd: module loaded
[    1.153169] loop: module loaded
[    1.158805] vchiq: vchiq_init_state: slot_zero = 0xba880000, is_master = 0
[    1.168977] Loading iSCSI transport class v2.0-870.
[    1.176400] usbcore: registered new interface driver smsc95xx
[    1.183718] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.391343] Core Release: 2.80a
[    1.395943] Setting default values for core params
[    1.402279] Finished setting default values for core params
[    1.609807] Using Buffer DMA mode
[    1.614614] Periodic Transfer Interrupt Enhancement - disabled
[    1.622021] Multiprocessor Interrupt Enhancement - disabled
[    1.629157] OTG VER PARAM: 0, OTG VER FLAG: 0
[    1.635043] Dedicated Tx FIFOs mode
[    1.640392] WARN::dwc_otg_hcd_init:1047: FIQ DMA bounce buffers: virt = 0xba814000 dma = 0xfa814000 len=9024
[    1.653419] FIQ FSM acceleration enabled for :
[    1.653419] Non-periodic Split Transactions
[    1.653419] Periodic Split Transactions
[    1.653419] High-Speed Isochronous Endpoints
[    1.676629] WARN::hcd_init_fiq:412: FIQ on core 1 at 0x803fcf78
[    1.684164] WARN::hcd_init_fiq:413: FIQ ASM at 0x803fd2d4 length 36
[    1.692056] WARN::hcd_init_fiq:438: MPHI regs_base at 0xbb89a000
[    1.699676] dwc_otg 3f980000.usb: DWC OTG Controller
[    1.706258] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[    1.715186] dwc_otg 3f980000.usb: irq 32, io mem 0x00000000
[    1.722379] Init: Port Power? op_state=1
[    1.727849] Init: Power Port (0)
[    1.732847] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.741233] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.750036] usb usb1: Product: DWC OTG Controller
[    1.756292] usb usb1: Manufacturer: Linux 4.1.17-v7+ dwc_otg_hcd
[    1.763834] usb usb1: SerialNumber: 3f980000.usb
[    1.770863] hub 1-0:1.0: USB hub found
[    1.776276] hub 1-0:1.0: 1 port detected
[    1.782554] usbcore: registered new interface driver usb-storage
[    1.790325] mousedev: PS/2 mouse device common for all mice
[    1.798196] bcm2835-cpufreq: min=600000 max=900000
[    1.804775] sdhci: Secure Digital Host Controller Interface driver
[    1.812493] sdhci: Copyright(c) Pierre Ossman
[    1.818852] mmc-bcm2835 3f300000.mmc: mmc_debug:0 mmc_debug2:0
[    1.826264] mmc-bcm2835 3f300000.mmc: DMA channels allocated
[    1.866449] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.876434] ledtrig-cpu: registered to indicate activity on CPUs
[    1.884294] hidraw: raw HID events driver (C) Jiri Kosina
[    1.891568] usbcore: registered new interface driver usbhid
[    1.898721] usbhid: USB HID core driver
[    1.904591] Initializing XFRM netlink socket
[    1.910461] NET: Registered protocol family 17
[    1.915509] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.918722] mmc0: new high speed SDHC card at address aaaa
[    1.919327] mmcblk0: mmc0:aaaa SL32G 29.7 GiB
[    1.920925]  mmcblk0: p1 p2
[    1.945205] Key type dns_resolver registered
[    1.951785] Registering SWP/SWPB emulation handler
[    1.959134] registered taskstats version 1
[    1.965061] vc-sm: Videocore shared memory driver
[    1.971358] [vc_sm_connected_init]: start
[    1.976265] Indeed it is in host mode hprt0 = 00021501
[    1.984258] [vc_sm_connected_init]: end - returning 0
[    2.041655] EXT4-fs (mmcblk0p2): warning: mounting unchecked fs, running e2fsck is recommended
[    2.156135] usb 1-1: new high-speed USB device number 2 using dwc_otg
[    2.164431] Indeed it is in host mode hprt0 = 00001101
[    2.206005] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)
[    2.216912] VFS: Mounted root (ext4 filesystem) on device 179:2.
[    2.250871] devtmpfs: mounted
[    2.256444] Freeing unused kernel memory: 440K (80776000 - 807e4000)
[    2.366528] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[    2.375076] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.385036] hub 1-1:1.0: USB hub found
[    2.390713] hub 1-1:1.0: 5 ports detected
[    2.676147] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[    2.790018] NET: Registered protocol family 10
[    2.796627] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[    2.805426] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.817813] smsc95xx v1.0.4
[    2.880432] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:31:15:2a
[    2.938371] random: init urandom read with 72 bits of entropy available
[    5.631969] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    7.749287] Bridge firewalling registered
[    7.788946] nf_conntrack version 0.5.0 (14814 buckets, 59256 max)
[    7.859274] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.775424] random: nonblocking pool is initialized
[   15.318263] device veth5dc9b2b entered promiscuous mode
[   15.326669] IPv6: ADDRCONF(NETDEV_UP): veth5dc9b2b: link is not ready
[   16.238903] cgroup: docker (77) created nested cgroup for controller "memory" which has incomplete hierarchy support. Nested cgroups may change behavior in the future.
[   16.258620] cgroup: "memory" requires setting use_hierarchy to 1 on the root
[   16.351801] eth0: renamed from veth1bed399
[   16.410425] IPv6: ADDRCONF(NETDEV_CHANGE): veth5dc9b2b: link becomes ready
[   16.419121] docker-sys: port 1(veth5dc9b2b) entered forwarding state
[   16.427120] docker-sys: port 1(veth5dc9b2b) entered forwarding state
[   16.636559] IPv6: eth0: IPv6 duplicate address fe80::42:acff:fe12:1 detected!
[   17.368982] udevd[9]: starting version 3.1.2
[   17.460096] docker-sys: port 1(veth5dc9b2b) entered disabled state
[   17.469124] veth1bed399: renamed from eth0
[   18.632055] bcm2835-rng 3f104000.rng: hwrng registered
[   18.639869] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[   18.680159] docker-sys: port 1(veth5dc9b2b) entered disabled state
[   18.697411] device veth5dc9b2b left promiscuous mode
[   18.704398] docker-sys: port 1(veth5dc9b2b) entered disabled state
[   19.800012] udevd[1]: starting version 3.1.2
[   20.877647] 9pnet: Installing 9P2000 support
[   20.893616] 9p: Installing v9fs 9p2000 file system support
[   20.901985] 9pnet: Could not find request transport: virtio
[   23.911744] device vetha283f55 entered promiscuous mode
[   23.931235] IPv6: ADDRCONF(NETDEV_UP): vetha283f55: link is not ready
[   24.288850] eth0: renamed from veth84b4742
[   24.328196] IPv6: ADDRCONF(NETDEV_CHANGE): vetha283f55: link becomes ready
[   24.336973] docker-sys: port 1(vetha283f55) entered forwarding state
🐳
Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0xf00
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.1.17-v7+ (dc4@dc4-XPS13-9333) (gcc version 4.8.3 20140303 (prerelease) (crosstool-NG linaro-1.13.1+bzr2650 - Linaro GCC 2014.03) ) #838 SMP Tue Feb 9 13:15:09 GMT 2016
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Raspberry Pi 2 Model B Rev 1.1
[    0.000000] cma: Reserved 8 MiB at 0x3a400000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] [bcm2709_smp_init_cpus] enter (9420->f3003010)
[    0.000000] [bcm2709_smp_init_cpus] ncores=4
[    0.000000] PERCPU: Embedded 12 pages/cpu @bafb1000 s20416 r8192 d20544 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 239540
[    0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2709.boardrev=0xa01041 bcm2709.serial=0x3431152a smsc95xx.macaddr=B8:27:EB:31:15:2A bcm2708_fb.fbswap=1 bcm2709.uart_clock=3000000 bcm2709.disk_led_gpio=47 bcm2709.disk_led_active_low=0 sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  +dwc_otg.lpm_enable=0 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 cgroup-enable=memory swapaccount=1 elevator=deadline rootwait console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 console=tty0 rancher.password=rancher rw init=/init
[    0.000000] Enabling memory control group subsystem
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 939508K/966656K available (5944K kernel code, 534K rwdata, 1660K rodata, 440K init, 757K bss, 18956K reserved, 8192K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xbb800000 - 0xff000000   (1080 MB)
[    0.000000]     lowmem  : 0x80000000 - 0xbb000000   ( 944 MB)
[    0.000000]     modules : 0x7f000000 - 0x80000000   (  16 MB)
[    0.000000]       .text : 0x80008000 - 0x807753c4   (7605 kB)
[    0.000000]       .init : 0x80776000 - 0x807e4000   ( 440 kB)
[    0.000000]       .data : 0x807e4000 - 0x80869a68   ( 535 kB)
[    0.000000]        .bss : 0x8086c000 - 0x8092975c   ( 758 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000] NR_IRQS:608
[    0.000000] Architected cp15 timer(s) running at 19.20MHz (phys).
[    0.000000] clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000010] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000031] Switching to timer-based delay loop, resolution 52ns
[    0.000313] Console: colour dummy device 80x30
[    0.001567] console [tty1] enabled
[    0.001627] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.001703] pid_max: default: 32768 minimum: 301
[    0.002081] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.002137] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.003443] Initializing cgroup subsys blkio
[    0.003516] Initializing cgroup subsys memory
[    0.003603] Initializing cgroup subsys devices
[    0.003664] Initializing cgroup subsys freezer
[    0.003733] Initializing cgroup subsys net_cls
[    0.003840] CPU: Testing write buffer coherency: ok
[    0.003948] ftrace: allocating 20289 entries in 60 pages
[    0.054230] CPU0: update cpu_capacity 1024
[    0.054307] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00
[    0.054346] [bcm2709_smp_prepare_cpus] enter
[    0.054496] Setting up static identity map for 0x8240 - 0x8274
[    0.057015] [bcm2709_boot_secondary] cpu:1 started (0) 17
[    0.057460] [bcm2709_secondary_init] enter cpu:1
[    0.057519] CPU1: update cpu_capacity 1024
[    0.057528] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
[    0.058108] [bcm2709_boot_secondary] cpu:2 started (0) 18
[    0.058465] [bcm2709_secondary_init] enter cpu:2
[    0.058495] CPU2: update cpu_capacity 1024
[    0.058504] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
[    0.059043] [bcm2709_boot_secondary] cpu:3 started (0) 18
[    0.059301] [bcm2709_secondary_init] enter cpu:3
[    0.059329] CPU3: update cpu_capacity 1024
[    0.059337] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
[    0.059426] Brought up 4 CPUs
[    0.059538] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[    0.059572] CPU: All CPU(s) started in HYP mode.
[    0.059601] CPU: Virtualization extensions available.
[    0.060618] devtmpfs: initialized
[    0.084995] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.085375] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.086525] pinctrl core: initialized pinctrl subsystem
[    0.087360] NET: Registered protocol family 16
[    0.093275] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[    0.094811] bcm2709.uart_clock = 3000000
[    0.100092] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.100152] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.100381] Serial: AMBA PL011 UART driver
[    0.100593] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 83, base_baud = 0) is a PL011 rev2
[    0.620614] console [ttyAMA0] enabled
[    0.624888] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[    0.699493] bcm2708-dmaengine 3f007000.dma: DMA legacy API manager at f3007000, dmachans=0xf35
[    0.708229] bcm2708-dmaengine 3f007000.dma: Initialized 7 DMA channels (+ 1 legacy)
[    0.716639] bcm2708-dmaengine 3f007000.dma: Load BCM2835 DMA engine driver
[    0.723556] bcm2708-dmaengine 3f007000.dma: dma_debug:0
[    0.729517] SCSI subsystem initialized
[    0.733522] usbcore: registered new interface driver usbfs
[    0.739147] usbcore: registered new interface driver hub
[    0.744613] usbcore: registered new device driver usb
[    0.750380] raspberrypi-firmware soc:firmware: Attached to firmware from 2016-02-01 17:51
[    0.786143] Switched to clocksource arch_sys_counter
[    0.838407] FS-Cache: Loaded
[    0.841687] CacheFiles: Loaded
[    0.856049] NET: Registered protocol family 2
[    0.861756] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.869006] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.875657] TCP: Hash tables configured (established 8192 bind 8192)
[    0.882184] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.888203] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.895036] NET: Registered protocol family 1
[    0.899861] RPC: Registered named UNIX socket transport module.
[    0.905803] RPC: Registered udp transport module.
[    0.910560] RPC: Registered tcp transport module.
[    0.915279] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.923102] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.932693] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.955176] VFS: Disk quotas dquot_6.6.0
[    0.959547] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.969121] FS-Cache: Netfs 'nfs' registered for caching
[    0.975588] NFS: Registering the id_resolver key type
[    0.980753] Key type id_resolver registered
[    0.984952] Key type id_legacy registered
[    0.991680] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.999346] io scheduler noop registered
[    1.003301] io scheduler deadline registered (default)
[    1.008812] io scheduler cfq registered
[    1.015162] BCM2708FB: allocated DMA memory fa800000
[    1.020258] BCM2708FB: allocated DMA channel 0 @ f3007000
[    1.031299] Console: switching to colour frame buffer device 82x26
[    1.042763] Serial: 8250/16550 driver, 0 ports, IRQ sharing disabled
[    1.051374] KGDB: Registered I/O driver kgdboc
[    1.106871] vc-cma: Videocore CMA driver
[    1.112476] vc-cma: vc_cma_base      = 0x00000000
[    1.118855] vc-cma: vc_cma_size      = 0x00000000 (0 MiB)
[    1.125810] vc-cma: vc_cma_initial   = 0x00000000 (0 MiB)
[    1.132937] vc-mem: phys_addr:0x00000000 mem_base=0x3dc00000 mem_size:0x3f000000(1008 MiB)
[    1.160051] brd: module loaded
[    1.173483] loop: module loaded
[    1.179142] vchiq: vchiq_init_state: slot_zero = 0xba880000, is_master = 0
[    1.189343] Loading iSCSI transport class v2.0-870.
[    1.196747] usbcore: registered new interface driver smsc95xx
[    1.204071] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.411705] Core Release: 2.80a
[    1.411716] Setting default values for core params
[    1.411760] Finished setting default values for core params
[    1.612191] Using Buffer DMA mode
[    1.617024] Periodic Transfer Interrupt Enhancement - disabled
[    1.624412] Multiprocessor Interrupt Enhancement - disabled
[    1.631546] OTG VER PARAM: 0, OTG VER FLAG: 0
[    1.637458] Dedicated Tx FIFOs mode
[    1.642789] WARN::dwc_otg_hcd_init:1047: FIQ DMA bounce buffers: virt = 0xba814000 dma = 0xfa814000 len=9024
[    1.655808] FIQ FSM acceleration enabled for :
[    1.655808] Non-periodic Split Transactions
[    1.655808] Periodic Split Transactions
[    1.655808] High-Speed Isochronous Endpoints
[    1.679014] WARN::hcd_init_fiq:412: FIQ on core 1 at 0x803fcf78
[    1.686546] WARN::hcd_init_fiq:413: FIQ ASM at 0x803fd2d4 length 36
[    1.694435] WARN::hcd_init_fiq:438: MPHI regs_base at 0xbb89a000
[    1.702051] dwc_otg 3f980000.usb: DWC OTG Controller
[    1.708635] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[    1.717586] dwc_otg 3f980000.usb: irq 32, io mem 0x00000000
[    1.724749] Init: Port Power? op_state=1
[    1.730215] Init: Power Port (0)
[    1.735209] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.743598] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.752406] usb usb1: Product: DWC OTG Controller
[    1.758667] usb usb1: Manufacturer: Linux 4.1.17-v7+ dwc_otg_hcd
[    1.766237] usb usb1: SerialNumber: 3f980000.usb
[    1.773255] hub 1-0:1.0: USB hub found
[    1.778632] hub 1-0:1.0: 1 port detected
[    1.784937] usbcore: registered new interface driver usb-storage
[    1.792691] mousedev: PS/2 mouse device common for all mice
[    1.800560] bcm2835-cpufreq: min=600000 max=900000
[    1.807206] sdhci: Secure Digital Host Controller Interface driver
[    1.814901] sdhci: Copyright(c) Pierre Ossman
[    1.821235] mmc-bcm2835 3f300000.mmc: mmc_debug:0 mmc_debug2:0
[    1.828653] mmc-bcm2835 3f300000.mmc: DMA channels allocated
[    1.866290] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.876234] ledtrig-cpu: registered to indicate activity on CPUs
[    1.884047] hidraw: raw HID events driver (C) Jiri Kosina
[    1.891319] usbcore: registered new interface driver usbhid
[    1.899507] usbhid: USB HID core driver
[    1.907444] Initializing XFRM netlink socket
[    1.914327] NET: Registered protocol family 17
[    1.920514] Key type dns_resolver registered
[    1.927029] Registering SWP/SWPB emulation handler
[    1.934212] registered taskstats version 1
[    1.940119] vc-sm: Videocore shared memory driver
[    1.946387] [vc_sm_connected_init]: start
[    1.952529] [vc_sm_connected_init]: end - returning 0
[    1.960674] Waiting for root device /dev/mmcblk0p2...
[    1.976294] Indeed it is in host mode hprt0 = 00021501
[    1.986199] mmc0: host does not support reading read-only switch, assuming write-enable
[    2.000520] mmc0: new high speed SDHC card at address aaaa
[    2.008213] mmcblk0: mmc0:aaaa SL32G 29.7 GiB
[    2.015770]  mmcblk0: p1 p2
[    2.145922] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)
[    2.156206] usb 1-1: new high-speed USB device number 2 using dwc_otg
[    2.156660] Indeed it is in host mode hprt0 = 00001101
[    2.171515] VFS: Mounted root (ext4 filesystem) on device 179:2.
[    2.181862] devtmpfs: error mounting -2
[    2.188070] Freeing unused kernel memory: 440K (80776000 - 807e4000)
[    2.356677] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[    2.365215] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.375157] hub 1-1:1.0: USB hub found
[    2.380885] hub 1-1:1.0: 5 ports detected
[    2.666212] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[    2.722051] NET: Registered protocol family 10
[    2.786619] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[    2.795446] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.807620] smsc95xx v1.0.4
[    2.870702] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:31:15:2a
[    4.942987] random: ros urandom read with 83 bits of entropy available
[    5.114830] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    8.007509] Bridge firewalling registered
[    8.044108] nf_conntrack version 0.5.0 (14814 buckets, 59256 max)
[    8.113149] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.802575] cgroup: docker (81) created nested cgroup for controller "memory" which has incomplete hierarchy support. Nested cgroups may change behavior in the future.
[   10.822098] cgroup: "memory" requires setting use_hierarchy to 1 on the root
[   12.346797] random: nonblocking pool is initialized
[   12.547050] device veth27ba0a2 entered promiscuous mode
[   12.555260] IPv6: ADDRCONF(NETDEV_UP): veth27ba0a2: link is not ready
[   12.819200] eth0: renamed from veth01378c9
[   12.828984] udevd[12]: starting version 3.1.2
[   12.870258] IPv6: ADDRCONF(NETDEV_CHANGE): veth27ba0a2: link becomes ready
[   12.879140] docker-sys: port 1(veth27ba0a2) entered forwarding state
[   12.887268] docker-sys: port 1(veth27ba0a2) entered forwarding state
[   12.906879] IPv6: eth0: IPv6 duplicate address fe80::42:acff:fe12:1 detected!
[   14.130291] bcm2835-rng 3f104000.rng: hwrng registered
[   14.137818] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[   14.542605] docker-sys: port 1(veth27ba0a2) entered disabled state
[   14.568277] veth01378c9: renamed from eth0
[   14.891378] docker-sys: port 1(veth27ba0a2) entered disabled state
[   14.908914] device veth27ba0a2 left promiscuous mode
[   14.915659] docker-sys: port 1(veth27ba0a2) entered disabled state
[   15.318919] udevd[1]: starting version 3.1.2
[   16.592148] 9pnet: Installing 9P2000 support
[   16.608411] 9p: Installing v9fs 9p2000 file system support
[   16.618567] 9pnet: Could not find request transport: virtio
[   19.541346] device veth4f6fed4 entered promiscuous mode
[   19.550244] IPv6: ADDRCONF(NETDEV_UP): veth4f6fed4: link is not ready
[   19.838795] eth0: renamed from vethee3c1c5
[   19.898261] IPv6: ADDRCONF(NETDEV_CHANGE): veth4f6fed4: link becomes ready
[   19.907074] docker-sys: port 1(veth4f6fed4) entered forwarding state
[   19.915112] docker-sys: port 1(veth4f6fed4) entered forwarding state
[   19.942661] IPv6: eth0: IPv6 duplicate address fe80::42:acff:fe12:1 detected!
[   21.165475] cfg80211: Calling CRDA to update world regulatory domain
[   21.439002] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[   21.447980] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   23.098381] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   23.107278] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1
[   23.630405] docker-sys: port 1(veth4f6fed4) entered disabled state
[   23.639422] vethee3c1c5: renamed from eth0
[   23.758111] docker-sys: port 1(veth4f6fed4) entered disabled state
[   23.775271] device veth4f6fed4 left promiscuous mode
[   23.782124] docker-sys: port 1(veth4f6fed4) entered disabled state
[   24.316267] cfg80211: Calling CRDA to update world regulatory domain
[   25.162808] 9pnet: Could not find request transport: virtio
[   27.466242] cfg80211: Calling CRDA to update world regulatory domain
[   30.312956] device veth829d57b entered promiscuous mode
[   30.322407] IPv6: ADDRCONF(NETDEV_UP): veth829d57b: link is not ready
[   30.549599] eth0: renamed from veth8888836
[   30.625025] IPv6: ADDRCONF(NETDEV_CHANGE): veth829d57b: link becomes ready
[   30.634106] docker-sys: port 1(veth829d57b) entered forwarding state
[   30.642265] docker-sys: port 1(veth829d57b) entered forwarding state
[   30.699976] cfg80211: Calling CRDA to update world regulatory domain
[   31.496763] IPv6: eth0: IPv6 duplicate address fe80::42:acff:fe12:1 detected!
[   31.549086] veth8888836: renamed from eth0
[   31.626840] docker-sys: port 1(veth829d57b) entered disabled state
[   31.768203] docker-sys: port 1(veth829d57b) entered disabled state
[   31.785233] device veth829d57b left promiscuous mode
[   31.791822] docker-sys: port 1(veth829d57b) entered disabled state
[   33.856212] cfg80211: Calling CRDA to update world regulatory domain
[   37.006213] cfg80211: Calling CRDA to update world regulatory domain
[   40.156211] cfg80211: Calling CRDA to update world regulatory domain
[   43.306223] cfg80211: Calling CRDA to update world regulatory domain
[   46.456211] cfg80211: Calling CRDA to update world regulatory domain
[   49.606265] cfg80211: Calling CRDA to update world regulatory domain
[   52.756237] cfg80211: Calling CRDA to update world regulatory domain
[   55.906215] cfg80211: Exceeded CRDA call max attempts. Not calling CRDA
[   88.722054] IPv6: ADDRCONF(NETDEV_UP): docker0: link is not ready