Skip to content

Instantly share code, notes, and snippets.

@DieterReuter

DieterReuter/gist:6f96900d921cab310937154a59f1af9f

Created February 9, 2017 20:50
Show Gist options
  • Save DieterReuter/6f96900d921cab310937154a59f1af9f to your computer and use it in GitHub Desktop.
Save DieterReuter/6f96900d921cab310937154a59f1af9f to your computer and use it in GitHub Desktop.
Download ZIP
Beelink GT1, Bootlog - "sudo screen /dev/cu.usbserial 115200"
Raw
gistfile1.txt
OSX: dieter@DietersMacBookPro in ~
🐳 ls -al /dev/cu.*
crw-rw-rw- 1 root wheel 36, 1 Feb 4 13:27 /dev/cu.Bluetooth-Incoming-Port
GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 216488
BL2 Built : 19:58:22, Aug 31 2016.
gxl g54c8aee - xiaobo.gu@droid05
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00015400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a9a00
NOTICE: BL3-1: v1.0(debug):2e39a99
NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
aml log : bl31 normal boot !
[Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
OPS=0x82
fc c2 9 21 fb ca c 14 7e b4 40 63 [0.460939 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gd267f87 (Nov 17 2016 - 19:17:36)
DRAM: 2 GiB
Relocation Offset is: 76ec9000
register usb cfg[0][1] = 0000000077f5f5d8
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073ec96b0
aml_priv->desc_buf = 0x0000000073ecb9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ece270,dt_addr=0000000073ed9270
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000080000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 80000000 1
13: data d7c00000 2c5400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=cold_boot
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 4 vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
rx version is 1.4 or below div=10
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[CANVAS]canvas init
[CANVAS]addr=0x3d851000 width=5760, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
get_cpu_id flag_12bit=1
SARADC open channel(0).
SARADC channel(0) is 0x3ca, Out of range(0x0~0x50)!
saradc - saradc sub-system
Usage:
saradc saradc open <channel> - open a SARADC channel
saradc close - close the SARADC
saradc getval - get the value in current channel
saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
get_cpu_id flag_12bit=1
InUsbBurn
noSof
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =73f4e440
copy done
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x02106540
Loading Ramdisk to 73dd7000, end 73eb6f67 ... OK
Loading Device Tree to 000000001fff2000, end 000000001ffff1ca ... OK
signature:
fdt_instaboot: no instaboot image
Starting kernel ...
uboot time: 2427588 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-g223e67e (lhh@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Thu Nov 17 19:36:40 CST 2016
[ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000@0] no prop version_code
[ 0.000000@0] bootconsole [earlycon0] enabled
[ 0.000000@0] fdt Reserved memory table:
[ 0.000000@0] linux,di: 0x000000007d300000 - 0x000000007f100000 (30 MiB)
[ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007d300000, size 30 MiB
[ 0.000000@0] linux,ion-dev: 0x0000000079300000 - 0x000000007d300000 (64 MiB)
[ 0.000000@0] linux,ppmgr: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] linux,codec_mm_cma: 0x0000000067c00000 - 0x0000000073c00000 (192 MiB)
[ 0.000000@0] linux,picdec: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] Reserved memory: incorrect alignment of CMA region
[ 0.000000@0] linux,codec_mm_reserved: 0x0000000075200000 - 0x0000000079300000 (65 MiB)
[ 0.000000@0] fdt Reserved memory total: 354 MiB
[ 0.000000@0] cma: Reserved 8 MiB at 74800000
[ 0.000000@0] psci: probing function IDs from device-tree
[ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc07516e000 s19968 r8192 d20992 u49152
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 510280
[ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=disabled logo=osd1,loaded,0x3d800000,1080p60hz maxcpus=8 vout=1080p60hz,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 androidboot.firstboot=0 jtag=apao androidboot.hardware=amlogic mac=86:37:20:48:cb:3e androidboot.mac=86:37:20:48:cb:3e
[ 0.000000@0] logo: osd1
[ 0.000000@0] logo: loaded
[ 0.000000@0] logo: 0x3d800000
[ 0.000000@0] logo: 1080p60hz
[ 0.000000@0] vout_serve: 1080p60hz
[ 0.000000@0] vout_serve: enable: 1
[ 0.000000@0] logo: get hdmimode: 1080p60hz
[ 0.000000@0] logo: get cvbsmode: 576cvbs
[ 0.000000@0] tv_vout: cvbs performance line = 0
[ 0.000000@0] jtag: jtag select 2
[ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000@0] Memory: 1643716K/2077696K available (10612K kernel code, 1153K rwdata, 3884K rodata, 1263K init, 5869K bss, 433980K reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
[ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff80423cc800 ( 35 MB)
[ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc07f100000 ( 2033 MB)
[ 0.000000@0] .init : 0xffffffc001eaa000 - 0xffffffc001fe5e00 ( 1264 kB)
[ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001ea9334 ( 14501 kB)
[ 0.000000@0] .data : 0xffffffc001fe6000 - 0xffffffc002106540 ( 1154 kB)
[ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01ea8fff]
[ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000@0] arch_multi_cluster:1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[ 0.008244@0] meson_bc_timer: mclk->mux_reg =ffffff8000014990,mclk->reg =ffffff8000016994
[ 0.016820@0] Console: colour dummy device 80x25
[ 0.021095@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.031671@0] pid_max: default: 32768 minimum: 301
[ 0.036581@0] Security Framework initialized
[ 0.040785@0] SELinux: Initializing.
[ 0.044530@0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.051366@0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.061621@0] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
[ 0.065713@0] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
[ 0.072720@0] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
[ 0.079712@0] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
[ 0.090063@0] Initializing cgroup subsys debug
[ 0.091174@0] Initializing cgroup subsys freezer
[ 0.095842@0] ftrace: allocating 36489 entries in 143 pages
[ 0.149544@0] /cpus/cpu@0: Missing clock-frequency property
[ 0.149588@0] /cpus/cpu@1: Missing clock-frequency property
[ 0.155163@0] /cpus/cpu@2: Missing clock-frequency property
[ 0.160792@0] /cpus/cpu@3: Missing clock-frequency property
[ 0.166365@0] /cpus/cpu@100: Missing clock-frequency property
[ 0.172146@0] /cpus/cpu@101: Missing clock-frequency property
[ 0.177915@0] /cpus/cpu@102: Missing clock-frequency property
[ 0.183697@0] /cpus/cpu@103: Missing clock-frequency property
[ 0.189465@0] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 0.239811@0] Meson chip version = RevA (22:A - 82:0)
[ 0.258218@1] CPU1: Booted secondary processor
[ 0.278186@2] CPU2: Booted secondary processor
[ 0.298193@3] CPU3: Booted secondary processor
[ 0.318219@4] CPU4: Booted secondary processor
[ 0.338219@5] CPU5: Booted secondary processor
[ 0.358233@6] CPU6: Booted secondary processor
[ 0.378257@7] CPU7: Booted secondary processor
[ 0.378350@0] Brought up 8 CPUs
[ 0.407172@0] SMP: Total of 8 processors activated.
[ 0.420159@2] sched: registering cpufreq notifiers for scale-invariant loads
[ 0.421689@2] instabooting: 0
[ 0.433835@2] pinctrl core: initialized pinctrl subsystem
[ 0.434535@2] regulator-dummy: no parameters
[ 0.438817@2] NET: Registered protocol family 16
[ 0.444435@3] ramoops: using module parameters
[ 0.447681@2] console [pstore-1] enabled
[ 0.451019@2] pstore: Registered ramoops as persistent store backend
[ 0.457395@2] ramoops: attached 0x100000@0x7300000, ecc: 0/0
[ 0.464022@3] cpuidle: using governor menu
[ 0.467465@3] aml_vdac_init: module init
[ 0.471352@2] register canvas platform driver
[ 0.475632@2] register rdma platform driver
[ 0.481321@2] vdso: 2 pages (1 code, 1 data) at base ffffffc001ff0000
[ 0.486237@2] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.493565@2] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.500475@2] software IO TLB [mem 0x64800000-0x64c00000] (4MB) mapped at [ffffffc064800000-ffffffc064bfffff]
[ 0.509459@2] Serial: AMBA PL011 UART driver
[ 0.514324@3] aml_i2c version: 20140813
[ 0.517855@3] i2c-core: driver [pmu4] using legacy resume method
[ 0.523848@2] codec_mm:codec_mm_module_init
[ 0.528088@3] aml_watch_point_probe, in
[ 0.532160@2] gxbb_mpll_clk: register mpll_clk_out0 success done
[ 0.537743@2] gxbb_mpll_clk: register mpll_clk_out1 success done
[ 0.543759@2] gxbb_mpll_clk: register mpll_clk_out2 success done
[ 0.550009@2] clk_sys: register PLL sys_pll success done
[ 0.555141@2] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
[ 0.560503@2] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
[ 0.565633@2] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
[ 0.571151@2] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
[ 0.577094@2] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
[ 0.583062@2] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
[ 0.588907@2] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
[ 0.594774@2] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
[ 0.600632@2] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
[ 0.606529@2] gxl_clk: clock initialization complete
[ 0.611691@2] clkmsr: Gxl msr_clk_reg0=ffffff800003c75c,msr_clk_reg2=ffffff800003e764
[ 0.621971@2] aml_iomap: amlogic iomap probe done
[ 0.624729@2] pinmux-gxl c1109880.pinmux: Init pinux probe!
[ 0.630674@2] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
[ 0.636903@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.644411@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ 0.652634@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.660503@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
domain-0 init dvfs: 4
domain-1 init dvfs: 4
[ 0.680705@2] codec_mm has 2 memory regions
[ 0.680775@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.687377@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.695992@3] codec_mm has 2 memory regions
[ 0.700076@3] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.708126@3] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.718694@2] vpu: driver version: v02
[ 0.720385@2] vpu: load vpu_clk: 666667000Hz(7)
[ 0.725004@2] vpu: vpu_probe OK
[ 0.729817@2] tv_vout: tvout_probe
[ 0.731480@2] tv_vout: major number 254 for disp
[ 0.736108@2] vout_notify: vout_register_server
[ 0.740671@2] tv_vout: register tv module server ok
[ 0.745677@2] tv_vout: tvout_probe OK
[ 0.749900@2] canvas_probe reg=00000000c8838000,size=400
[ 0.754630@2] canvas maped reg_base =ffffff800009a000
[ 0.763908@2] rdma_probe
[ 1.079297@2] bio: create slab <bio-0> at 0
[ 1.080489@2] SCSI subsystem initialized
[ 1.082407@2] usbcore: registered new interface driver usbfs
[ 1.087773@3] usbcore: registered new interface driver hub
[ 1.093366@2] usbcore: registered new device driver usb
[ 1.099340@0] i2c-gpio i2c_gpio.38: using pins 172 (SDA) and 173 (SCL)
[ 1.105024@3] Linux video capture interface: v2.00
[ 1.109979@3] pps_core: LinuxPPS API ver. 1 registered
[ 1.114863@3] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 1.124281@3] PTP clock support registered
[ 1.129615@3] hdmitx: system: amhdmitx_init
[ 1.132521@3] hdmitx: system: Ver: 2014May6
[ 1.136901@3] hdmitx: system: amhdmitx_probe
[ 1.141353@0] hdmitx: system: not find match init-data
[ 1.146171@0] hdmitx: system: not find match pwr-ctl
[ 1.151179@0] hdmitx hpd irq = 89
[ 1.154967@0] hdmitx20: Mapped PHY: 0xc0800000
[ 1.158952@0] hdmitx20: Mapped PHY: 0xc1104400
[ 1.163532@0] hdmitx20: Mapped PHY: 0xc8100000
[ 1.167870@0] hdmitx20: Mapped PHY: 0xc8834000
[ 1.172332@0] hdmitx20: Mapped PHY: 0xc883a000
[ 1.176805@0] hdmitx20: Mapped PHY: 0xc883c000
[ 1.181260@0] hdmitx20: Mapped PHY: 0xd0100000
[ 1.185720@0] hdmitx20: Mapped PHY: 0xda83a000
[ 1.190226@0] hdmitx: alread display in uboot 0x10
[ 1.195013@0] avmute set to 1
[ 1.198399@3] vout_serve: vout_init_module
[ 1.202235@3] tv_vout: tv_set_current_vmode[759]fps_target_mode=16
[ 1.205075@0] hdmitx: system: irq 80000002
[ 1.212425@3] tv_vout: mode is 16,sync_duration_den=1,sync_duration_num=60
[ 1.219323@3] tv_vout: already display in uboot
[ 1.223873@3] vout_serve: vinfo mode is: 1080p60hz
[ 1.228680@3] vout_serve: init mode 1080p60hz
[ 1.233182@2] vout_serve: create vout attribute OK
[ 1.237869@2] vout_serve: meson_vout_probe OK
[ 1.242483@2] logo: logo_init
[ 1.245638@2] osd_rdma: osd_rdma_init: rdma_table p=0x74841000,op=0x74841000 , v=0xffffff800009e000
[ 1.254331@2] osd_rdma: osd rdma request irq as second interrput function!
[ 1.261749@2] Advanced Linux Sound Architecture Driver Initialized.
[ 1.268244@2] Bluetooth: Core ver 2.18
[ 1.271410@2] NET: Registered protocol family 31
[ 1.275931@2] Bluetooth: HCI device and connection manager initialized
[ 1.282516@2] Bluetooth: HCI socket layer initialized
[ 1.287572@2] Bluetooth: L2CAP socket layer initialized
[ 1.292852@2] Bluetooth: SCO socket layer initialized
[ 1.298414@2] cfg80211: Calling CRDA to update world regulatory domain
[ 1.304605@0] NetLabel: Initializing
[ 1.308044@0] NetLabel: domain hash size = 128
[ 1.312645@0] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.317842@0] NetLabel: unlabeled traffic allowed by default
[ 1.325532@1] Switched to clocksource arch_sys_counter
[ 1.375330@0] [amlatvdemod..]aml_atvdemod_init.
[ 1.375468@0] NET: Registered protocol family 2
[ 1.379506@0] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.386442@0] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 1.393355@0] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.399970@0] TCP: reno registered
[ 1.403267@0] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 1.409522@0] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 1.416698@0] NET: Registered protocol family 1
[ 1.420943@0] RPC: Registered named UNIX socket transport module.
[ 1.426820@0] RPC: Registered udp transport module.
[ 1.431729@0] RPC: Registered tcp transport module.
[ 1.436609@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.443466@0] aml_wifi wifi.33: [wifi_dev_probe] no power_on_pin2
[ 1.449440@0] aml_wifi wifi.33: [wifi_dev_probe] set pwm as 32k output
[ 1.455995@0] aml_wifi wifi.33: [wifi_dev_probe] dhd_static_buf setup
[ 1.462477@0] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem: WIFI MEM Allocated
[ 1.470106@0] aml_wifi wifi.33: [wifi_dev_probe] interrupt_pin=241
[ 1.476246@0] aml_wifi wifi.33: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
[ 1.483693@0] aml_wifi wifi.33: [wifi_dev_probe] power_on_pin=240
[ 1.489805@0] aml_wifi wifi.33: [wifi_dev_probe] clock_32k_pin=0
[ 1.496205@1] aml_wifi wifi.33: [wifi_setup_dt] wifi_setup_dt
[ 1.501648@1] aml_wifi wifi.33: [wifi_setup_dt] interrupt_pin(241)
[ 1.507847@1] aml_wifi wifi.33: [wifi_setup_dt] power_on_pin(240)
[ 1.514325@0] Unpacking initramfs...
[ 1.525679@3] hdmitx: plugin
[ 1.548952@0] Freeing initrd memory: 892K (ffffffc073dd7000 - ffffffc073eb6000)
[ 1.555603@0] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 1.557286@0] audit: initializing netlink subsys (disabled)
[ 1.562863@0] audit: type=2000 audit(1.460:1): initialized
[ 1.569271@2] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.582522@2] VFS: Disk quotas dquot_6.5.2
[ 1.582815@2] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.593011@2] NFS: Registering the id_resolver key type
[ 1.593087@2] Key type id_resolver registered
[ 1.597527@2] Key type id_legacy registered
[ 1.601555@2] NTFS driver 2.1.30 [Flags: R/O].
[ 1.606482@3] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.614064@3] fuse init (API version 7.22)
[ 1.626759@0] msgmni has been set to 3612
[ 1.628355@2] NET: Registered protocol family 38
[ 1.630239@2] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 1.637477@2] io scheduler noop registered
[ 1.641566@2] io scheduler deadline registered
[ 1.646411@0] io scheduler cfq registered (default)
[ 1.674289@3] hdmitx: edid: check sum valid
[ 1.674324@3] hdmitx: edid: check sum valid
[ 1.677148@3] hdmitx: edid: blk0 raw data
[ 1.681175@3] 00ffffffffffff001e6de37689bb02000b18010380502278eaca95a6554ea126
[ 1.681175@3] 0f50542108007140818081c0a9c0b300d1c0810001019d6770a0d0a022503020
[ 1.681175@3] 3a00204f3100001a000000fd00383d1e5a1e000a202020202020000000fc004c
[ 1.681175@3] 4720554c545241574944450a000000000000000000000000000000000000017c
[ 1.681175@3]
[ 1.681175@3]
[ 1.702073@0] meson-rng c8834000.rng: hwrng registered
[ 1.705812@0] loop: module loaded
[ 1.706432@2] zram: Created 1 device(s) ...
[ 1.707485@2] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.708323@2] tun: Universal TUN/TAP device driver, 1.6
[ 1.708325@2] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 1.744510@3] hdmitx: edid: blk1 raw data
[ 1.748556@3] 020317f14410040301230907078301000065030c0010009f3d70a0d0a0155030
[ 1.748556@3] 203a00204f3100001a7e4800e0a0381f4040403a00204f31000018011d007251
[ 1.748556@3] d01e206e285500204f3100001e8c0ad08a20e02d10103e9600204f3100001800
[ 1.748556@3] 0000ff003431314b4b484e35393038310a0000000000000000000000000000ce
[ 1.748556@3]
[ 1.748556@3]
[ 1.780897@3] EDID Parser:
[ 1.783647@3] hdmitx: edid: find IEEEOUT
[ 1.787577@3]
[ 1.789198@3] hdmitx: edid: check sum valid
[ 1.793396@3] hdmitx: edid: check sum valid
[ 1.797618@3] hdmitx: update RX hdr info 0
[ 1.803732@3] hdmitx: ddc rd8b error 0x3a 0x00 0x00
[ 1.808660@3] [RX]-receive ksv list len:1,depth:1,cas:0,dev:0
[ 1.812389@3] hdmitx: video: get current mode: 1080p60hz
[ 1.817730@3] hdmitx: update rx hdr info 0
[ 1.821850@3] hdmitx: get ext_name (null)
[ 1.825869@3] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 16
[ 1.832603@3] hdmtix: set audio
[ 1.834569@2] libphy: stmmac: probed
[ 1.834574@2] eth0: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[ 1.834577@2] eth0: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07)
[ 1.835047@2] PPP generic driver version 2.4.2
[ 1.835260@2] PPP BSD Compression module registered
[ 1.835262@2] PPP Deflate Compression module registered
[ 1.835281@2] PPP MPPE Compression module registered
[ 1.835283@2] NET: Registered protocol family 24
[ 1.835433@1] usbcore: registered new interface driver asix
[ 1.835610@2] usbcore: registered new interface driver ax88179_178a
[ 1.835735@1] usbcore: registered new interface driver cdc_ether
[ 1.835838@2] usbcore: registered new interface driver net1080
[ 1.835939@1] usbcore: registered new interface driver cdc_subset
[ 1.836033@2] usbcore: registered new interface driver zaurus
[ 1.836158@1] usbcore: registered new interface driver cdc_ncm
[ 1.836476@1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.836479@1] ehci-h20ahb: H20AHB-EHCI Host Controller driver
[ 1.836721@2] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.837085@2] usbcore: registered new interface driver cdc_acm
[ 1.837087@2] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.837200@1] usbcore: registered new interface driver usb-storage
[ 1.837434@1] usbcore: registered new interface driver usbserial
[ 1.838145@2] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff80000da000
[ 1.838361@1] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
[ 1.838382@1] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff80000ee080
[ 1.839031@1] mousedev: PS/2 mouse device common for all mice
[ 1.839553@0] usbcore: registered new interface driver xpad
[ 1.839771@0] i2c /dev entries driver
[ 1.840121@2] usbcore: registered new interface driver uvcvideo
[ 1.840122@2] USB Video Class driver (1.1.1)
[ 1.841001@2] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: [email protected]
[ 1.841101@2] Bluetooth: HCI UART driver ver 2.2
[ 1.841104@2] Bluetooth: HCI H4 protocol initialized
[ 1.841456@2] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
[ 1.843691@0] cpu cpu4: bL_cpufreq_init: CPU 4 initialized
[ 1.843852@0] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
[ 1.844138@0] CPUidle arm64: cpuidle init start!!
[ 1.844923@0] @@@@@@@@@@_____2______in dia_init()
[ 1.845167@0] ATVR driver - init called!
[ 1.845168@0] usbcore: registered new interface driver usbhid
[ 1.845169@0] usbhid: USB HID core driver
[ 1.845543@0] ashmem: initialized
[ 1.845718@1] logger: created 256K log 'log_main'
[ 1.845873@0] logger: created 256K log 'log_events'
[ 1.846049@0] logger: created 256K log 'log_radio'
[ 1.846195@2] logger: created 256K log 'log_system'
[ 1.847332@0] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff80000fc4c0
[ 1.847354@0] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
[ 2.115946@3] hdmitx tx_aud_src = 0
[ 2.119448@3] hdmitx: fs = 0, cd = 4, tmds_clk = 148500
[ 2.124671@3] hdmitx aud_n_para = 6144
[ 2.128455@3] hdmitx set channel status
[ 2.137800@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
[ 2.140430@0] console [ttyS0] enabled
[ 2.140430@0] console [ttyS0] enabled
[ 2.147711@0] bootconsole [earlycon0] disabled
[ 2.147711@0] bootconsole [earlycon0] disabled
[ 2.156876@0] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff80000fe4c0
[ 2.163501@0] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
[ 2.173599@3] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff]
[ 2.182715@3] meson-gpu-clkgen: probe of c883c000.gpu_clk failed with error -16
[ 2.190241@2] hdmitx: system: hdmitx_hdcp_init
[ 2.194505@2] ESM HLD: Initializing...
[ 2.198060@2] ESM HLD: Registering device range 'esm'...
[ 2.203304@2] ESM HLD: Device range 'esm' has been registered.
[ 2.209092@2] ESM HLD: Creating class /sys/class/elliptic...
[ 2.214784@3] ESM HLD: The class /sys/class/elliptic has been created.
[ 2.221162@3] ESM HLD: Creating device 'esm'...
[ 2.225776@3] ESM HLD: Device 'esm' has been created.
[ 2.230639@3] ESM HLD: Done initializing the HLD driver.
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[ 2.251873@2] aml_vrtc rtc.32: rtc core: registered aml_vrtc as rtc0
[ 2.253266@3] secmon has 1 memory regions
[ 2.256600@3] secmon: share in base: 0xffffff800011a000, share out base: 0xffffff800011c000
[ 2.264835@3] secmon secmon.4: assigned reserved memory node linux,secmon ok
[ 2.271821@3] secmon: probe done
[ 2.275343@3] storage: storage in base: 0xffffff8001800000
[ 2.280455@3] storage: storage out base: 0xffffff8001880000
[ 2.285965@3] storage: storage block base: 0xffffff8001900000
[ 2.291651@3] storage: probe done!
[ 2.295567@2] aml_sd_emmc_probe: line 3558
[ 2.299075@2] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
[ 2.308971@2] aml_sd_emmc_reg_init 1146
[ 2.312318@2] get property: ocr_avail, value:0x00200080
[ 2.318751@2] get property: f_min, value:300000
[ 2.324859@2] get property: f_max, value:100000000
[ 2.331269@2] get property: max_req_size, value:0x00020000
[ 2.337721@2] get property: pinname, str:emmc
[ 2.343490@2] get property: card_type, value:1
[ 2.349205@2] get property: gpio_dat3, str:
[ 2.354616@2] get property: hw_reset, str:
[ 2.360086@2] emmc:pdata->caps = c0000d47
[ 2.364020@2] emmc:pdata->caps2 = 18060
[ 2.367830@2] storage 1, boot 1
[ 2.370916@2] get_storage_dev return 1
[ 2.405543@3] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.405762@3] aml_sd_emmc_probe: line 3558
[ 2.410177@3] aml_sd_emmc_reg_init 1146
[ 2.413635@3] get property: ocr_avail, value:0x00200080
[ 2.420068@3] get property: f_min, value:400000
[ 2.426183@3] get property: f_max, value:100000000
[ 2.432560@3] get property: max_req_size, value:0x00020000
[ 2.439033@3] get property: irq_in, value:3
[ 2.444720@3] get property: irq_out, value:5
[ 2.450427@3] get property: gpio_cd, str:
[ 2.455852@3] get property: pinname, str:sd
[ 2.461454@3] get property: jtag_pin, str:
[ 2.466894@3] get property: card_type, value:5
[ 2.472581@3] get property: gpio_dat3, str:
[ 2.478030@3] sd:pdata->caps = 7
[ 2.481204@3] sd:pdata->caps2 = 0
[ 2.515738@3] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.515772@4] [aml_is_card_insert] card OUT
[ 2.515848@5] [aml_is_card_insert] card OUT
[ 2.524234@3] aml_sd_emmc_probe: line 3558
[ 2.528607@3] aml_sd_emmc_reg_init 1146
[ 2.532107@3] get property: ocr_avail, value:0x00200080
[ 2.538537@3] get property: f_min, value:400000
[ 2.544650@3] get property: f_max, value:200000000
[ 2.551038@3] get property: max_req_size, value:0x00020000
[ 2.557511@3] get property: pinname, str:sdio
[ 2.563280@3] get property: card_type, value:3
[ 2.569016@3] sdio:pdata->caps = 7810f
[ 2.572681@3] sdio:pdata->caps2 = 0
[ 2.592289@1] emmc: BKOPS_EN bit is not set
[ 2.601445@1] emmc: trying cali 0-th time(s)
[ 2.605532@1] emmc: delay[0]= 4400 padding= 3, bidx=4
[ 2.605554@1] emmc: delay[1]= 4400 padding= 3, bidx=4
[ 2.610078@1] emmc: delay[2]= 4200 padding= 4, bidx=4
[ 2.615081@1] emmc: delay[3]= 4600 padding= 2, bidx=4
[ 2.620093@1] emmc: delay[4]= 4600 padding= 2, bidx=4
[ 2.620106@2] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.620477@3] ion_dev has 1 memory regions
[ 2.634926@1] emmc: delay[5]= 4600 padding= 2, bidx=4
[ 2.636600@3] fb: osd_init_module
[ 2.636728@3] fb: viu vsync irq: 35
[ 2.636735@3] fb: failed to init reserved memory
[ 2.636747@3] fb: osd_probe vinfo:ffffffc002086d98
[ 2.636751@3] fb: init fbdev bpp is:32
[ 2.659692@1] emmc: delay[6]= 4400 padding= 3, bidx=4
[ 2.664680@1] emmc: delay[7]= 4600 padding= 2, bidx=4
[ 2.664687@1] emmc: calibration result @ 0: max(4600), min(4200)
[ 2.664690@1] emmc: line_delay =0x1000211, max_cal_result =4600
[ 2.664691@1] emmc: base_index_max 4, base_index_min 4
[ 2.664698@1] emmc: clk 100000000 SDR mode tuning start
[ 2.665444@1] emmc: rx_tuning_result[0] = 10
[ 2.665984@1] emmc: rx_tuning_result[1] = 10
[ 2.666520@1] emmc: rx_tuning_result[2] = 10
[ 2.667054@1] emmc: rx_tuning_result[3] = 10
[ 2.667589@1] emmc: rx_tuning_result[4] = 10
[ 2.668126@1] emmc: rx_tuning_result[5] = 10
[ 2.668662@1] emmc: rx_tuning_result[6] = 10
[ 2.669199@1] emmc: rx_tuning_result[7] = 10
[ 2.669735@1] emmc: rx_tuning_result[8] = 10
[ 2.669845@1] emmc: best_win_start =0, best_win_size =9
[ 2.669847@1] emmc: sd_emmc_regs->gclock=0x100024a,sd_emmc_regs->gadjust=0x42000
[ 2.669851@1] emmc: gclock =0x100024a, gdelay=0x1000211, gadjust=0x42000
[ 2.670186@1] emmc: new HS200 MMC card at address 0001
[ 2.670601@2] emmc: clock 100000000, 8-bit-bus-width
[ 2.670601@2]
[ 2.670602@2] mmcblk0: emmc:0001 NCard 14.4 GiB
[ 2.670727@2] mmcblk0boot0: emmc:0001 NCard partition 1 4.00 MiB
[ 2.670857@2] mmcblk0boot1: emmc:0001 NCard partition 2 4.00 MiB
[ 2.670974@2] mmcblk0rpmb: emmc:0001 NCard partition 3 4.00 MiB
[ 2.671582@1] mmcblk0: unknown partition table
[ 2.672316@2] [mmc_read_partition_tbl] mmc read partition OK!
[ 2.672317@2] add_emmc_partition
[ 2.672497@1] [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
[ 2.672635@2] [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
[ 2.672762@1] [mmcblk0p03] cache offset 0x000006c00000, size 0x000020000000
[ 2.672889@2] [mmcblk0p04] env offset 0x000027400000, size 0x000000800000
[ 2.673019@1] [mmcblk0p05] logo offset 0x000028400000, size 0x000002000000
[ 2.673147@2] [mmcblk0p06] recovery offset 0x00002ac00000, size 0x000002000000
[ 2.673268@1] [mmcblk0p07] rsv offset 0x00002d400000, size 0x000000800000
[ 2.673393@2] [mmcblk0p08] tee offset 0x00002e400000, size 0x000000800000
[ 2.673514@1] [mmcblk0p09] crypt offset 0x00002f400000, size 0x000002000000
[ 2.673631@2] [mmcblk0p10] misc offset 0x000031c00000, size 0x000002000000
[ 2.673759@1] [mmcblk0p11] instaboot offset 0x000034400000, size 0x000020000000
[ 2.673887@2] [mmcblk0p12] boot offset 0x000054c00000, size 0x000002000000
[ 2.674012@1] [mmcblk0p13] system offset 0x000057400000, size 0x000080000000
[ 2.674140@2] [mmcblk0p14] data offset 0x0000d7c00000, size 0x0002c5400000
[ 2.674171@2] card key: card_blk_probe.
[ 2.674174@2] emmc_key_init:527 emmc key lba_start:0x12020,lba_end:0x12220
[ 2.674178@2] emmc key: emmc_key_init:552 ok.
[ 2.674360@2] amlmmc_dtb_init: register dtb chardev
[ 2.674444@1] amlmmc_dtb_init: register dtb chardev OK
[ 2.674444@1] Exit aml_emmc_partition_ops OK.
[ 2.675494@2] mmcblk0boot1: unknown partition table
[ 2.676376@2] mmcblk0boot0: unknown partition table
[ 2.676642@1] clear_emmc_wait_flag
[ 2.962708@0] fb: osd probe OK
[ 2.963008@2] ge2d: ge2d_init_module
[ 2.963679@2] ge2d: ge2d_dev major:242
[ 2.967802@3] ge2d: ge2d clock is 400 MHZ
[ 2.971350@3] ge2d: ge2d: pdev=ffffffc06560b600, irq=182, rstc=0xffffffc064439c00, clk=ffffffc065658800
[ 2.980711@3] ge2d: mapped phy: 0xd0160000
[ 2.984717@3] ge2d: ge2d start monitor
[ 2.988492@0] ge2d: ge2d workqueue monitor start
[ 2.988710@3] sysled: module init
[ 2.988835@3] sysled: led_gpio = 154
[ 2.988837@3] sysled: active_low = 0
[ 2.988994@2] sysled: module probed ok
[ 2.989398@3] pwmled: module init
[ 2.989486@3] codec:Amlogic A/V streaming port init
[ 2.990811@3] codec:get gate demux control ok ffffffc064552ac0
[ 2.990816@3] codec:get gate parser_top control ok ffffffc0645528c0
[ 2.990820@3] codec:get gate vpu_intr control ok ffffffc0645526c0
[ 2.990826@3] codec:get gate vdec control ok ffffffc0645524c0
[ 2.991431@3] codec:[tsync_pcr_init]init success.
[ 2.991432@3] codec:amvideocap_init_module
[ 2.991552@3] codec:amvideocap_probe,amvideocap
[ 2.991555@3] codec:use cma buf.
[ 2.991556@3] codec:amvideocap_dev_register
[ 2.993356@3] amvenc_avc_probe -- reserved memory config fail.
[ 2.993359@3] amvenc_avc - cma memory pool size: 40 MB
[ 2.993381@3] encode_wq_init.
[ 2.993385@3] encode start monitor.
[ 2.993438@1] encode workqueue monitor start.
[ 2.993889@3] jpegenc module init
[ 2.994201@3] codec:picdec_driver_probe called.
[ 2.994204@3] picdec has 1 memory regions
[ 2.994230@3] codec:picdec_driver_probe done.
[ 2.995169@3] codec:create_ge2d_work_queue video task ok
[ 2.995569@3] codec:used fix clk for vdec clk source!
[ 2.995575@3] codec:register clk_set_setting cpu[34]
[ 2.995908@3] vpu_init
[ 2.996091@3] vpu_probe
[ 2.996095@3] HevcEnc reserved memory config fail.
[ 2.996100@3] HevcEnc - cma memory pool size: 64 MB
[ 2.996102@3] HevcEnc - wave420l_irq: 219
[ 2.996143@3] vpu base address get from platform driver physical base addr=0xc8810000, virtual base=0xffffff8000258000
[ 2.996453@3] success to probe vpu device with video memory from cma
[ 2.996602@3] DI: di_module_init ok.
[ 2.996605@3] DI: di_module_init: major 235
[ 2.996807@3] DI: di_probe
[ 2.996914@3] deinterlace has 1 memory regions
[ 2.996949@3] deinterlace deinterlace.26: assigned reserved memory node linux,di ok
[ 2.996969@3] di_irq:78,timerc_irq:38
[ 3.173467@3] rdma_register, rdma_table_addr ffffff800017b000 rdma_table_addr_phy 74848000 reg_buf ffffffc063e04000
[ 3.183709@3] rdma_register success, handle 1 table_size 8192
[ 3.189412@2] DI: di_probe allocate rdma channel 1.
[ 3.194220@2] DI: DI hw version 2.
[ 3.198108@2] 0x000000db:Y=db,U=0,V=0
[ 3.201202@2] 0x000000dc:Y=dc,U=0,V=0
[ 3.204824@2] 0x000000dd:Y=dd,U=0,V=0
[ 3.208454@2] 0x000000de:Y=de,U=0,V=0
[ 3.212069@2] 0x000000df:Y=df,U=0,V=0
[ 3.215705@2] 0x000000e0:Y=e0,U=0,V=0
[ 3.219314@2] 0x000000e1:Y=e1,U=0,V=0
[ 3.222936@2] 0x000000e2:Y=e2,U=0,V=0
[ 3.226564@2] 0x000000e3:Y=e3,U=0,V=0
[ 3.230181@2] 0x000000f0:Y=f0,U=0,V=0
[ 3.233806@2] 0x000000f1:Y=f1,U=0,V=0
[ 3.237431@2] 0x000000f2:Y=f2,U=0,V=0
[ 3.241049@2] 0x000000f3:Y=f3,U=0,V=0
[ 3.244671@2] 0x000000f4:Y=f4,U=0,V=0
[ 3.248359@2] 0x000000f5:Y=f5,U=0,V=0
[ 3.251916@2] 0x000000f6:Y=f6,U=0,V=0
[ 3.255553@2] 0x000000f7:Y=f7,U=0,V=0
[ 3.259161@2] 0x000000f8:Y=f8,U=0,V=0
[ 3.262783@2] 0x000000f9:Y=f9,U=0,V=0
[ 3.266412@2] 0x000000fa:Y=fa,U=0,V=0
[ 3.270029@2] 0x000000fb:Y=fb,U=0,V=0
[ 3.273651@2] 0x000000fc:Y=fc,U=0,V=0
[ 3.277419@2] DI: di_probe here.
[ 3.280853@2] efusekeynum: 4
[ 3.283320@2] efusekeyname: mac offset: 0 size: 6
[ 3.289735@2] efusekeyname: mac_bt offset: 6 size: 6
[ 3.296100@2] efusekeyname: mac_wifi offset: 12 size: 6
[ 3.302462@2] efusekeyname: usid offset: 18 size: 16
[ 3.309157@2] efuse efuse.10: probe OK!
[ 3.313042@2] key unify config unifykey-num is 14
[ 3.317375@2] key unify fact unifykey-num is 14
[ 3.321782@2] aml_unifykeys_probe:1273=============unifykey_devno:e900000
[ 3.328817@2] 6unifykey: device unifykeys created ok
[ 3.333666@2] 6aml_unifykeys_init done!
[ 3.337424@2] PPMGRDRV: warn: ppmgr module init func called
[ 3.343065@2] PPMGRDRV: err: ppmgr_driver_probe called
[ 3.348026@2] ppmgr has 1 memory regions
[ 3.351911@2] PPMGRDRV: info: ppmgr_dev major:232
[ 3.356861@2] PPMGRDRV: info: ppmgr_probe done
[ 3.361390@2] amlogic rfkill init
[ 3.364329@2] enter bt_probe of_node
[ 3.367807@2] not get gpio_en
[ 3.370683@2] power on valid level is high
[ 3.374915@2] Bluetooth: BlueSleep Mode Driver Ver 1.2
[ 3.380417@2] ionvideo-000: V4L2 device registered as video13
[ 3.385558@2] ionvid: info: Video Technology Magazine Ion Video
[ 3.391383@2] ionvid: info: Capture Board ver 1.0 successfully loaded
[ 3.397792@2] audio_dsp: [dsp]register dsp to char divece(257)
[ 3.404244@2] amaudio: amaudio: driver amaudio succuess!
[ 3.409205@2] amlvid:err: amlvideo_init called
[ 3.413034@2] amlvid:err: amlvideo_create_instance called
[ 3.418586@2] amlvid:err: v4l2_dev.name=:amlvideo-000
[ 3.423729@3] amlvideo-000: V4L2 device registered as video10
[ 3.429691@2] vdin_drv_init: major 231
[ 3.433286@3] vdin_drv_init: vdin driver init done
[ 3.437741@3] tvafe_drv_init: major 230
[ 3.441869@2] tvafe: tvafe_init.
[ 3.444992@3] [RX]-hdmirx: hdmirx_init.
[ 3.448500@3] ESM HLD: Initializing...
[ 3.452189@3] ESM HLD: Registering device range 'esm_rx'...
[ 3.457723@3] ESM HLD: Device range 'esm_rx' has been registered.
[ 3.463746@3] ESM HLD: Creating class /sys/class/elliptic_rx...
[ 3.469751@2] ESM HLD: The class /sys/class/elliptic_rx has been created.
[ 3.476391@2] ESM HLD: Creating device 'esm_rx'...
[ 3.481249@2] ESM HLD: Device 'esm_rx' has been created.
[ 3.486381@2] ESM HLD: Done initializing the HLD driver.
[ 3.491607@2] [viuin..]viuin_init_module viuin module init
[ 3.497546@2] [viuin..]viuin_probe probe ok.
[ 3.501351@2] module init
[ 3.503991@2]
[ 3.503991@2] VECM probe start
[ 3.508945@3] aml_vecm_probe: ok
[ 3.512449@2] saradc c1108680.saradc: initialized by BL30
[ 3.517189@2] saradc c1108680.saradc: calibration start:
[ 3.522439@2] saradc c1108680.saradc: nominal=0, value=5
[ 3.527723@2] saradc c1108680.saradc: nominal=256, value=251
[ 3.533307@2] saradc c1108680.saradc: nominal=512, value=498
[ 3.538928@2] saradc c1108680.saradc: nominal=768, value=748
[ 3.544518@2] saradc c1108680.saradc: nominal=1023, value=993
[ 3.550214@2] saradc c1108680.saradc: calibration end: coef=4219
[ 3.556393@3] remote: Driver init
[ 3.559511@3] remote: platform_data g_remote_ao_offset=580
[ 3.564832@3] remote: platform_data irq =228
[ 3.569096@3] remote: set drvdata completed
[ 3.573293@3] remote: device_create_file completed
[ 3.578520@3] input: aml_keypad as /devices/meson-remote.12/input/input0
[ 3.585143@3] remote: input_register_device completed
[ 3.590078@3] remote: set_remote_mode[74]
[ 3.594009@3] remote: remote config major:227
[ 3.598628@3] remote: physical address:0x63db4000
[ 3.603671@2] gpio-key gpio_keypad.48: gpio_key: 0 name(power) pin()
[ 3.609381@2] gpio-key gpio_keypad.48: amlogic_gpio_name_map_num pin 0!::
[ 3.616127@2] gpio-key gpio_keypad.48: gpio_key: 0 power(147)
[ 3.621803@2] gpio-key gpio_keypad.48: start setup_timer
[ 3.627040@2] gpio-key gpio_keypad.48: power key(116) registed.
[ 3.633133@3] input: gpio_keypad as /devices/gpio_keypad.48/input/input1
[ 3.639710@3] gpio-key gpio_keypad.48: gpio keypad register input device completed.
[ 3.647134@3] input input1: gpio keypad major:226
[ 3.653067@3] Sensor: lsm303d_init
[ 3.655369@2] Sensor: stk8313_init
[ 3.658619@3] Sensor: stk831x_init
[ 3.661951@2] Sensor: mxc622x_acc_init
[ 3.665721@2] Sensor: mxc6255xc_acc_init
[ 3.669622@2] Sensor: l3gd20_gyr_init
[ 3.674070@2] aml dvb init
[ 3.676301@2] Amlogic Demod DVB-T/C DebugIF Init
[ 3.680535@3] Amlogic Demod DVB-T/C DebugIF Init ok----------------
[ 3.687481@2] jtag: module init
[ 3.689839@3] jtag: pinctrl setup apao
[ 3.693345@3] jtag: set state 2
efuse_pw_en: 0x3
WARNING! efuse bits is disabled
Enable A53 JTAG cluster 0 to AO
[ 3.709489@0] jtag: module probed ok
[ 3.709917@2] cpuinfo: probe done
[ 3.711117@2] defendkey c8834500.defendkey: defendkey_devno:de00000
[ 3.717387@3] defendkey c8834500.defendkey: defendkey: device defendkey created ok
[ 3.724695@2] defendkey: driver init
[ 3.728082@2] input input1: key 116 up
[ 3.732536@0] input: cec_input as /devices/virtual/input/input2
[ 3.737953@3] cectx aocec: no hdmirx reg resource
[ 3.742252@3] cectx aocec: no hhi reg resource
[ 3.746780@3] cectx aocec: can't find hdmirx
[ 3.751870@3] cec: wake up flag:0
[ 3.755064@3] aml_aes_dma c883e000.aml_aes: Aml AES_dma
[ 3.759972@0] aml_tdes_dma c883e000.aml_tdes: Aml TDES_dma
[ 3.765497@3] aml_sha_dma c883e000.aml_sha: Aml SHA1/SHA224/SHA256 dma
[ 3.771838@3] usbcore: registered new interface driver snd-usb-audio
[ 3.778991@3] aml_codec_T9015 c8832000.t9015: aml_T9015_audio_codec_probe
[ 3.786555@0] aml_pcm_dai: pcm mode detection =1
[ 3.789217@3] aml_spdif_dai: enterd aml_spdif_play,set_clock:-1,sample_rate=4
[ 3.795950@3] aml_spdif_dai: set normal 512 fs /4 fs
[ 3.800818@3] aml_audio_hw: IEC958 16bit
[ 3.804696@3] hdmitx: audio: aout notify rate 48000
[ 3.809531@3] hdmitx: audio: aout notify size 16
[ 3.814094@3] hdmitx: audio: aout notify format CT_PCM
[ 3.819210@3] hdmtix: set audio
[ 3.822299@3] hdmitx tx_aud_src = 0
[ 3.825769@3] hdmitx: fs = 3, cd = 4, tmds_clk = 148500
[ 3.830913@3] hdmitx aud_n_para = 6144
[ 3.834637@3] hdmitx set channel status
[ 3.838535@3] hdmitx: audio: Audio Type: PCM
[ 3.842643@3] hdmitx: audio: set audio param
[ 4.055749@0] aml_snd_card: headphone detection disable=1
[ 4.055785@0] aml_snd_card: no spk event delay time set
[ 4.061212@0] aml_snd_m8_card aml_m8_snd.47: T9015-audio-hifi <-> I2S.40 mapping ok
[ 4.068867@0] aml_snd_m8_card aml_m8_snd.47: dit-hifi <-> SPDIF.41 mapping ok
[ 4.075432@0] aml_pcm: enter aml_pcm_new dai->name: PCM.42 dai->id: 0
[ 4.081938@0] aml_snd_m8_card aml_m8_snd.47: pcm2bt-pcm <-> PCM.42 mapping ok
[ 4.088836@0] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTL
[ 4.096441@0] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
[ 4.105191@0] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTR
[ 4.112813@0] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
[ 4.123421@0] GACT probability NOT on
[ 4.125209@0] Mirror/redirect action on
[ 4.129032@0] u32 classifier
[ 4.131889@0] Actions configured
[ 4.135377@0] Netfilter messages via NETLINK v0.30.
[ 4.140275@0] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 4.146975@3] ctnetlink v0.93: registering with nfnetlink.
[ 4.152381@3] xt_time: kernel timezone is -0000
[ 4.156459@3] ipip: IPv4 over IPv4 tunneling driver
[ 4.161930@3] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 4.166755@3] arp_tables: (C) 2002 David S. Miller
[ 4.171405@3] TCP: cubic registered
[ 4.174791@3] Initializing XFRM netlink socket
[ 4.180109@0] NET: Registered protocol family 10
[ 4.184842@3] mip6: Mobile IPv6
[ 4.186924@3] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 4.192654@3] sit: IPv6 over IPv4 tunneling driver
[ 4.198515@3] NET: Registered protocol family 17
[ 4.201742@3] NET: Registered protocol family 15
[ 4.206475@3] Bridge firewalling registered
[ 4.210504@3] Bluetooth: RFCOMM TTY layer initialized
[ 4.215438@3] Bluetooth: RFCOMM socket layer initialized
[ 4.220716@3] Bluetooth: RFCOMM ver 1.11
[ 4.224564@3] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.230020@3] Bluetooth: BNEP filters: protocol multicast
[ 4.235348@3] Bluetooth: BNEP socket layer initialized
[ 4.240435@3] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 4.246494@3] Bluetooth: HIDP socket layer initialized
[ 4.251615@3] l2tp_core: L2TP core driver, V2.0
[ 4.256054@3] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 4.260955@3] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 4.266692@3] l2tp_netlink: L2TP netlink interface
[ 4.271427@3] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 4.277460@3] l2tp_debugfs: L2TP debugfs support
[ 4.282000@3] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 4.288608@3] NET: Registered protocol family 35
[ 4.293191@3] Key type dns_resolver registered
[ 4.298961@3] Registering SWP/SWPB emulation handler
[ 4.303226@3] regulator-dummy: disabling
[ 4.306781@3] aml_vrtc rtc.32: setting system clock to 2015-01-01 00:00:07 UTC (1420070407)
[ 4.316820@3] gxbb_pm: enter meson_pm_probe!
[ 4.318865@3] gxbb_pm: meson_pm_probe done
[ 4.323749@0] cpucore_cooling_register, max_cpu_core_num:4
[ 4.328573@0] cpucore_cooling_register, max_cpu_core_num:4
[ 4.349071@0] aml_istbt_dev_ready NULL
[ 4.34912 4.353806@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 4.357152@0] Freeing unused kernel memory: 1260K (ffffffc001eaa000 - ffffffc001fe5000)
[ 4.385749@2] init: init started!
[ 4.387268@2] init: init second stage started!
[ 4.388256@2] init: waitpid failed: No child processes
[ 4.393082@2] init: (Loading properties from /default.prop took 0.00s.)
[ 4.401170@2] init: (Parsing /init.environ.rc took 0.00s.)
[ 4.405132@2] init: (Parsing /init.usb.rc took 0.00s.)
[ 4.410983@2] init: (Parsing init.amlogic.usb.rc took 0.00s.)
[ 4.416206@2] init: (Parsing init.amlogic.usb.rc took 0.00s.)
[ 4.421402@2] init: (Parsing init.amlogic.board.rc took 0.01s.)
[ 4.427332@2] init: could not import file 'init.amlogic.wifi.rc' from '/init.amlogic.rc'
[ 4.435296@2] init: could not import file 'init.mtk.rc' from '/init.amlogic.rc'
[ 4.442554@2] init: (Parsing /init.amlogic.rc took 0.03s.)
[ 4.448438@2] init: (Parsing /init.usb.configfs.rc took 0.00s.)
[ 4.453894@2] init: (Parsing /init.zygote32.rc took 0.00s.)
[ 4.459487@2] init: (Parsing /init.trace.rc took 0.00s.)
[ 4.464611@2] init: (Parsing /init.rc took 0.06s.)
[ 4.469725@2] init: Starting service 'ueventd'...
[ 4.476039@2] ueventd: ueventd started!
[ 4.736 4.737248@6] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 4.761525@6] init: enter do_confirm_formated /dev/block/tee, /tee
[ 4.762078@6] init: blocksize 1024, bytes_per_inode 1024
[ 4.767379@6] init: do_confirm_formated ext4 try mount
[ 4.783203@7] EXT4-fs (mmcblk0p8): recovery complete
[ 4.783249@7] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
[ 4.832647@3] EXT4-fs (mmcblk0p13): mounted filesystem with ordered data mode. Opts: (null)
[ 4.835402@3] fs_mgr: __mount(source=/dev/block/system,target=/system,type=ext4)=0
[ 4.843517@3] EXT4-fs (mmcblk0p14): Ignoring removed nomblk_io_submit option
[ 5.152259@7] EXT4-fs (mmcblk0p14): recovery complete
[ 5.153200@7] EXT4-fs (mmcblk0p14): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 5.162482@7] fs_mgr: check_fs(): mount(/dev/block/data,/data,ext4)=0: Success
[ 5.213231@3] fs_mgr: check_fs(): unmount(/data) succeeded
[ 5.214052@3] fs_mgr: Running /system/bin/e2fsck on /dev/block/data
[ 5.296717@4] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 5.296717@4]
[ 5.297466@4] e2fsck: /dev/block/data: clean, 1320/727664 files, 170904/2905088 blocks
[ 5.297466@4]
[ 5.307737@4] EXT4-fs (mmcblk0p14): Ignoring removed nomblk_io_submit option
[ 5.318675@4] EXT4-fs (mmcblk0p14): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
[ 5.325183@4] fs_mgr: __mount(source=/dev/block/data,target=/data,type=ext4)=0
[ 5.332965@3] EXT4-fs (mmcblk0p3): Ignoring removed nomblk_io_submit option
[ 5.349418@3] EXT4-fs (mmcblk0p3): recovery complete
[ 5.350205@3] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 5.359428@3] fs_mgr: check_fs(): mount(/dev/block/cache,/cache,ext4)=0: Success
[ 5.417098@5] fs_mgr: check_fs(): unmount(/cache) succeeded
[ 5.417174@5] fs_mgr: Running /system/bin/e2fsck on /dev/block/cache
[ 5.444220@5] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 5.444220@5]
[ 5.444964@5] e2fsck: /dev/block/cache: clean, 17/32768 files, 4212/131072 blocks
[ 5.444964@5]
[ 5.454798@5] EXT4-fs (mmcblk0p3): Ignoring removed nomblk_io_submit option
[ 5.464813@3] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
[ 5.472099@3] fs_mgr: __mount(source=/dev/block/cache,target=/cache,type=ext4)=0
[ 5.480171@3] EXT4-fs (mmcblk0p8): Ignoring removed nomblk_io_submit option
[ 5.488854@3] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 5.496936@3] fs_mgr: check_fs(): mount(/dev/block/tee,/tee,ext4)=0: Success
[ 5.556925@3] fs_mgr: check_fs(): unmount(/tee) succeeded
[ 5.556992@3] fs_mgr: Running /system/bin/e2fsck on /dev/block/tee
[ 5.581572@3] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 5.581572@3]
[ 5.582304@3] e2fsck: /dev/block/tee: clean, 11/8192 files, 3111/8192 blocks
[ 5.582304@3]
[ 5.591546@3] EXT4-fs (mmcblk0p8): Ignoring removed nomblk_io_submit option
[ 5.600362@3] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
[ 5.609022@3] fs_mgr: __mount(source=/dev/block/tee,target=/tee,type=ext4)=0
[ 5.641891@7] Adding 511996k swap on /dev/block/zram0. Priority:-1 extents:1 across:511996k SS
[ 5.683295@7] EXT4-fs (zram0): mounted filesystem with ordered data mode. Opts: (null)
[ 5.688483@5] init: cannot find '/system/bin/tee-supplicant', disabling 'tee_supplicant'
[ 5.708932@5] init: /recovery not specified in fstab
[ 5.715301@2] logd.auditd: start
[ 5.741105@3] init: Failed to reload policy
[ 5.824756@1] dig: dig start!
[ 5.964682@3] mali_kbase: unknown parameter 'mali_debug_level' ignored
[ 5.965591@3] mali_kbase: unknown parameter 'mali_shared_mem_size' ignored
[ 5.974589@3] ftrace: Allocated trace_printk buffers
[ 5.979719@3] mali d00c0000.t82x: Continuing without Mali regulator control
[ 5.984243@3] mali d00c0000.t82x: set min pp to default 1
[ 5.989562@3] mali d00c0000.t82x: set min clk default to 0
[ 5.995059@3] mali d00c0000.t82x: dvfs table is 5
[ 5.999656@3] mali d00c0000.t82x: dvfs table addr ffffffc06368fa18, ele size=48
[ 6.006888@3] mali d00c0000.t82x: max clk set 3
[ 6.011365@3] mali d00c0000.t82x: turbo clk set to 4
[ 6.016288@3] mali d00c0000.t82x: default clk set to 1
[ 6.021432@3] mali_plat=ffffffbffc043568
[ 6.025707@3] gpu cooling register okay with err=0
[ 6.030175@3] gpu core cooling register okay with err=0
[ 6.035385@3] gpu_power_main, 63
[ 6.038539@3] hrtimer: interrupt took 12167 ns
[ 6.043218@3] mali d00c0000.t82x: GPU identified as 0x0820 r1p0 status 0
[ 6.050735@0] mali d00c0000.t82x: Probed as mali0
[ 6.060757@0] random: init urandom read with 80 bits of entropy available
[ 6.089780@2] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 6.090548@0] binder: 3754:3754 transaction failed 29189, size 0-0
[ 6.095931@0] amlkey_init() enter!
[ 6.102997@2] emmc_key_read:428, read ok
[ 6.105842@1] logd.daemon: reinit
[ 6.109471@2] amlkey_init() storagekey_info.buffer=ffffff8001900000, storagekey_info.size = 40000!
[ 6.109834@0] warning: `daemonsu' uses 32-bit capabilities (legacy support in use)
[ 6.127022@2] vfm_map_store:rm default
[ 6.129463@2] vfm_map_store:add default decoder ppmgr deinterlace amvideo
[ 6.136436@2] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
[ 6.145896@2] init: cannot expand '${ro.usb.vendor.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/vendor_string'
[ 6.158322@2] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
[ 6.168208@2] init: cannot expand '${ro.usb.product.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/product_string'
[ 6.180777@2] init: property_set("ro.radio.noril", "true" failed
[ 6.187881@2] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
[ 6.196337@2] init: cannot expand '${ro.usb.vendor.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/vendor_string'
[ 6.209000@2] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
[ 6.218599@2] init: cannot expand '${ro.usb.product.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/product_string'
[ 6.233022@2] init: cannot find '/system/bin/debuggerd64', disabling 'debuggerd64'
[ 6.237509@0] vout_serve: vmode set to 1080p60hz
[ 6.237512@0] vout_serve: don't set the same mode as current
[ 6.248943@2] init: cannot find '/system/bin/rild', disabling 'ril-daemon'
[ 6.257383@2] init: cannot find '/system/bin/install-recovery.sh', disabling 'flash_recovery'
root@q201_9377:/ # [ 6.269596@2] init: cannot find '/system/xbin/perfprofd', disabling 'perfprofd'
[ 6.273057@2] init: cannot find '/system/bin/tee-supplicant', disabling 'tee_supplicant'
Hello Jten!!!
Hello Jten!!!
Hello Jten!!!
[ 6.446978@2] remote: cur_mode = 0
[ 6.447019@2] remote: set_remote_mode[74]
[ 6.450609@2] remote: cur_mode = 0
[ 6.452087@2] remote: set_remote_mode[74]
[ 6.469166@3] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 6.548105@5] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 6.579610@5] fb: afbc: 1
[ 6.579677@5] fb: use ion buffer for fb memory
[ 6.581038@5] fb: OSD0 as afbcd mode
[ 6.584776@5] meson-fb meson-fb.16: create ion_client ffffffc063ec8c00, handle=ffffffc06388a440
[ 6.593263@5] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 8 MiB
[ 6.601948@5] fb: 0, phy: 0x0000000079300000, vir:0xffffff800317f000, size=8300K
[ 6.601948@5]
[ 6.611278@5] meson-fb meson-fb.16: create ion_client ffffffc063ec8c00, handle=ffffffc06388ad00
[ 6.619574@3] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079b1b000, size 8 MiB
[ 6.628200@3] fb: 0, phy: 0x0000000079b1b000, vir:0xffffff800399b000, size=8300K
[ 6.628200@3]
[ 6.637535@3] meson-fb meson-fb.16: create ion_client ffffffc063ec8c00, handle=ffffffc06111a400
[ 6.645823@3] meson-fb meson-fb.16: ion memory(0): created fb at 0x000000007a336000, size 8 MiB
[ 6.654441@3] fb: 0, phy: 0x000000007a336000, vir:0xffffff80041b7000, size=8300K
[ 6.654441@3]
[ 6.663525@3] fb: Frame buffer memory assigned at
[ 6.668010@3] fb: 0, phy: 0x0000000079300000, vir:0xffffff800317f000, size=8300K
[ 6.668010@3]
[ 6.677290@3] fb: 0, phy: 0x0000000079300000, vir:0xffffff800317f000, size=8300K
[ 6.677290@3]
[ 6.686298@3] fb: 0, phy: 0x0000000079b1b000, vir:0xffffff800399b000, size=8300K
[ 6.686298@3]
[ 6.695307@3] fb: 0, phy: 0x000000007a336000, vir:0xffffff80041b7000, size=8300K
[ 6.695307@3]
[ 6.704397@3] fb: ---------------clear fb0 memory ffffff800317f000
[ 6.712170@3] fb: ---------------clear fb0 memory ffffff800399b000
[ 6.718449@3] fb: ---------------clear fb0 memory ffffff80041b7000
[ 6.724434@3] fb: osd[0] canvas.idx =0x40
[ 6.726736@3] fb: osd[0] canvas.addr=0x79300000
[ 6.731186@3] fb: osd[0] canvas.width=7680
[ 6.735239@3] fb: osd[0] canvas.height=3240
[ 6.739409@3] fb: osd[0] frame.width=1920
[ 6.743348@3] fb: osd[0] frame.height=1080
[ 6.846369@7] fb: afbc: 1
[ 6.847029@7] fb: use ion buffer for fb memory
[ 6.847845@7] meson-fb meson-fb.16: create ion_client ffffffc063ec8c00, handle=ffffffc063882b40
[ 6.855875@4] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 6.862154@7] meson-fb meson-fb.16: ion memory(1): created fb at 0x000000007ab51000, size 1 MiB
[ 6.870677@7] fb: Frame buffer memory assigned at
[ 6.875125@7] fb: 1, phy: 0x000000007ab51000, vir:0xffffff8004aff000, size=1024K
[ 6.875125@7]
[ 6.884393@7] fb: fb1 open, logo index:1
[ 6.937261@0] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 7.039636@7] fb: osd[1] enable: 0 scale:0x0 (systemcontrol)
[ 7.039679@7] fb: osd[0] enable: 1 scale:0x10001 (systemcontrol)
[ 7.046066@7] fb: free_scale_switch to fb0, mode: 0x10001
[ 7.051283@7] vout_serve: osd0=> x:0,y:0,w:1920,h:1080
[ 7.051283@7] osd1=> x:0,y:0,w:18,h:18
[ 7.059821@7] fb: current vmode=1080p60hz
[ 7.079675@7] fb: osd[1] set scale, h_scale: ENABLE, v_scale: ENABLE
[ 7.080390@7] fb: osd[1].scaledata: 1920 1920 1080 1080
[ 7.085579@7] fb: osd[1].pandata: 0 0 0 0
[ 7.091298@4] healthd: No charger supplies found
[ 7.094393@4] healthd: No battery devices found
[ 8.288637@6] random: nonblocking pool is initialized
[ 11.332230@1] request_suspend_state: wakeup (3->0) at 11236701713 (2015-01-01 00:00:14.525460961 UTC)
[ 11.335790@1] request_suspend_state,168,old_sleep=0,new_state=0
[ 12.109135@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.109762@3] audio_dsp: last mode 0,now 0
[ 12.113884@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.120100@3] audio_dsp: last mode 0,now 0
[ 12.125029@5] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.130356@1] audio_dsp: last mode 0,now 0
[ 12.134451@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.140634@1] audio_dsp: last mode 0,now 0
[ 12.161544@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.162176@4] audio_dsp: last mode 0,now 0
[ 12.166351@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.172440@4] audio_dsp: last mode 0,now 0
[ 12.177069@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.182705@4] audio_dsp: last mode 0,now 0
[ 12.186881@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.192966@4] audio_dsp: last mode 0,now 0
[ 12.384177@4] tv_vout: vout [tv_set_vframe_rate_end_hint] return mode = 16, policy = 1!
[ 7.085579@7] fb: osd[1].pandata: 0 0 0 0
[ 7.091298@4] healthd: No charger supplies found
[ 7.094393@4] healthd: No battery devices found
[ 8.288637@6] random: nonblocking pool is initialized
[ 11.332230@1] request_suspend_state: wakeup (3->0) at 11236701713 (2015-01-01 00:00:14.525460961 UTC)
[ 11.335790@1] request_suspend_state,168,old_sleep=0,new_state=0
[ 12.109135@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.109762@3] audio_dsp: last mode 0,now 0
[ 12.113884@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.120100@3] audio_dsp: last mode 0,now 0
[ 12.125029@5] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.130356@1] audio_dsp: last mode 0,now 0
[ 12.134451@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.140634@1] audio_dsp: last mode 0,now 0
[ 12.161544@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.162176@4] audio_dsp: last mode 0,now 0
[ 12.166351@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.172440@4] audio_dsp: last mode 0,now 0
[ 12.177069@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.182705@4] audio_dsp: last mode 0,now 0
[ 12.186881@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.192966@4] audio_dsp: last mode 0,now 0
[ 12.384177@4] tv_vout: vout [tv_set_vframe_rate_end_hint] return mode = 16, policy = 1!
[ 7.051283@7] vout_serve: osd0=> x:0,y:0,w:1920,h:1080
[ 7.051283@7] osd1=> x:0,y:0,w:18,h:18
[ 7.059821@7] fb: current vmode=1080p60hz
[ 7.079675@7] fb: osd[1] set scale, h_scale: ENABLE, v_scale: ENABLE
[ 7.080390@7] fb: osd[1].scaledata: 1920 1920 1080 1080
[ 7.085579@7] fb: osd[1].pandata: 0 0 0 0
[ 7.091298@4] healthd: No charger supplies found
[ 7.094393@4] healthd: No battery devices found
[ 8.288637@6] random: nonblocking pool is initialized
[ 11.332230@1] request_suspend_state: wakeup (3->0) at 11236701713 (2015-01-01 00:00:14.525460961 UTC)
[ 11.335790@1] request_suspend_state,168,old_sleep=0,new_state=0
[ 12.109135@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.109762@3] audio_dsp: last mode 0,now 0
[ 12.113884@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.120100@3] audio_dsp: last mode 0,now 0
[ 12.125029@5] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.130356@1] audio_dsp: last mode 0,now 0
[ 12.134451@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.140634@1] audio_dsp: last mode 0,now 0
[ 12.161544@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.162176@4] audio_dsp: last mode 0,now 0
[ 12.166351@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.172440@4] audio_dsp: last mode 0,now 0
[ 12.177069@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.182705@4] audio_dsp: last mode 0,now 0
[ 12.186881@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.192966@4] audio_dsp: last mode 0,now 0
[ 12.384177@4] tv_vout: vout [tv_set_vframe_rate_end_hint] return mode = 16, policy = 1!
[ 6.743348@3] fb: osd[0] frame.height=1080
[ 6.846369@7] fb: afbc: 1
[ 6.847029@7] fb: use ion buffer for fb memory
[ 6.847845@7] meson-fb meson-fb.16: create ion_client ffffffc063ec8c00, handle=ffffffc063882b40
[ 6.855875@4] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 6.862154@7] meson-fb meson-fb.16: ion memory(1): created fb at 0x000000007ab51000, size 1 MiB
[ 6.870677@7] fb: Frame buffer memory assigned at
[ 6.875125@7] fb: 1, phy: 0x000000007ab51000, vir:0xffffff8004aff000, size=1024K
[ 6.875125@7]
[ 6.884393@7] fb: fb1 open, logo index:1
[ 6.937261@0] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 7.039636@7] fb: osd[1] enable: 0 scale:0x0 (systemcontrol)
[ 7.039679@7] fb: osd[0] enable: 1 scale:0x10001 (systemcontrol)
[ 7.046066@7] fb: free_scale_switch to fb0, mode: 0x10001
[ 7.051283@7] vout_serve: osd0=> x:0,y:0,w:1920,h:1080
[ 7.051283@7] osd1=> x:0,y:0,w:18,h:18
[ 7.059821@7] fb: current vmode=1080p60hz
[ 7.079675@7] fb: osd[1] set scale, h_scale: ENABLE, v_scale: ENABLE
[ 7.080390@7] fb: osd[1].scaledata: 1920 1920 1080 1080
[ 7.085579@7] fb: osd[1].pandata: 0 0 0 0
[ 7.091298@4] healthd: No charger supplies found
[ 7.094393@4] healthd: No battery devices found
[ 8.288637@6] random: nonblocking pool is initialized
[ 11.332230@1] request_suspend_state: wakeup (3->0) at 11236701713 (2015-01-01 00:00:14.525460961 UTC)
[ 11.335790@1] request_suspend_state,168,old_sleep=0,new_state=0
[ 12.109135@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.109762@3] audio_dsp: last mode 0,now 0
[ 12.113884@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.120100@3] audio_dsp: last mode 0,now 0
[ 12.125029@5] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.130356@1] audio_dsp: last mode 0,now 0
[ 12.134451@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.140634@1] audio_dsp: last mode 0,now 0
[ 12.161544@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.162176@4] audio_dsp: last mode 0,now 0
[ 12.166351@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.172440@4] audio_dsp: last mode 0,now 0
[ 12.177069@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.182705@4] audio_dsp: last mode 0,now 0
[ 12.186881@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.192966@4] audio_dsp: last mode 0,now 0
[ 12.384177@4] tv_vout: vout [tv_set_vframe_rate_end_hint] return mode = 16, policy = 1!
[ 6.731186@3] fb: osd[0] canvas.width=7680
[ 6.735239@3] fb: osd[0] canvas.height=3240
[ 6.739409@3] fb: osd[0] frame.width=1920
[ 6.743348@3] fb: osd[0] frame.height=1080
[ 6.846369@7] fb: afbc: 1
[ 6.847029@7] fb: use ion buffer for fb memory
[ 6.847845@7] meson-fb meson-fb.16: create ion_client ffffffc063ec8c00, handle=ffffffc063882b40
[ 6.855875@4] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 6.862154@7] meson-fb meson-fb.16: ion memory(1): created fb at 0x000000007ab51000, size 1 MiB
[ 6.870677@7] fb: Frame buffer memory assigned at
[ 6.875125@7] fb: 1, phy: 0x000000007ab51000, vir:0xffffff8004aff000, size=1024K
[ 6.875125@7]
[ 6.884393@7] fb: fb1 open, logo index:1
[ 6.937261@0] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 7.039636@7] fb: osd[1] enable: 0 scale:0x0 (systemcontrol)
[ 7.039679@7] fb: osd[0] enable: 1 scale:0x10001 (systemcontrol)
[ 7.046066@7] fb: free_scale_switch to fb0, mode: 0x10001
[ 7.051283@7] vout_serve: osd0=> x:0,y:0,w:1920,h:1080
[ 7.051283@7] osd1=> x:0,y:0,w:18,h:18
[ 7.059821@7] fb: current vmode=1080p60hz
[ 7.079675@7] fb: osd[1] set scale, h_scale: ENABLE, v_scale: ENABLE
[ 7.080390@7] fb: osd[1].scaledata: 1920 1920 1080 1080
[ 7.085579@7] fb: osd[1].pandata: 0 0 0 0
[ 7.091298@4] healthd: No charger supplies found
[ 7.094393@4] healthd: No battery devices found
[ 8.288637@6] random: nonblocking pool is initialized
[ 11.332230@1] request_suspend_state: wakeup (3->0) at 11236701713 (2015-01-01 00:00:14.525460961 UTC)
[ 11.335790@1] request_suspend_state,168,old_sleep=0,new_state=0
[ 12.109135@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.109762@3] audio_dsp: last mode 0,now 0
[ 12.113884@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.120100@3] audio_dsp: last mode 0,now 0
[ 12.125029@5] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.130356@1] audio_dsp: last mode 0,now 0
[ 12.134451@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.140634@1] audio_dsp: last mode 0,now 0
[ 12.161544@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.162176@4] audio_dsp: last mode 0,now 0
[ 12.166351@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.172440@4] audio_dsp: last mode 0,now 0
[ 12.177069@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.182705@4] audio_dsp: last mode 0,now 0
[ 12.186881@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.192966@4] audio_dsp: last mode 0,now 0
[ 12.384177@4] tv_vout: vout [tv_set_vframe_rate_end_hint] return mode = 16, policy = 1!
[ 6.731186@3] fb: osd[0] canvas.width=7680
[ 6.735239@3] fb: osd[0] canvas.height=3240
[ 6.739409@3] fb: osd[0] frame.width=1920
[ 6.743348@3] fb: osd[0] frame.height=1080
[ 6.846369@7] fb: afbc: 1
[ 6.847029@7] fb: use ion buffer for fb memory
[ 6.847845@7] meson-fb meson-fb.16: create ion_client ffffffc063ec8c00, handle=ffffffc063882b40
[ 6.855875@4] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 6.862154@7] meson-fb meson-fb.16: ion memory(1): created fb at 0x000000007ab51000, size 1 MiB
[ 6.870677@7] fb: Frame buffer memory assigned at
[ 6.875125@7] fb: 1, phy: 0x000000007ab51000, vir:0xffffff8004aff000, size=1024K
[ 6.875125@7]
[ 6.884393@7] fb: fb1 open, logo index:1
[ 6.937261@0] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 7.039636@7] fb: osd[1] enable: 0 scale:0x0 (systemcontrol)
[ 7.039679@7] fb: osd[0] enable: 1 scale:0x10001 (systemcontrol)
[ 7.046066@7] fb: free_scale_switch to fb0, mode: 0x10001
[ 7.051283@7] vout_serve: osd0=> x:0,y:0,w:1920,h:1080
[ 7.051283@7] osd1=> x:0,y:0,w:18,h:18
[ 7.059821@7] fb: current vmode=1080p60hz
[ 7.079675@7] fb: osd[1] set scale, h_scale: ENABLE, v_scale: ENABLE
[ 7.080390@7] fb: osd[1].scaledata: 1920 1920 1080 1080
[ 7.085579@7] fb: osd[1].pandata: 0 0 0 0
[ 7.091298@4] healthd: No charger supplies found
[ 7.094393@4] healthd: No battery devices found
[ 8.288637@6] random: nonblocking pool is initialized
[ 11.332230@1] request_suspend_state: wakeup (3->0) at 11236701713 (2015-01-01 00:00:14.525460961 UTC)
[ 11.335790@1] request_suspend_state,168,old_sleep=0,new_state=0
[ 12.109135@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.109762@3] audio_dsp: last mode 0,now 0
[ 12.113884@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.120100@3] audio_dsp: last mode 0,now 0
[ 12.125029@5] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.130356@1] audio_dsp: last mode 0,now 0
[ 12.134451@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.140634@1] audio_dsp: last mode 0,now 0
[ 12.161544@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.162176@4] audio_dsp: last mode 0,now 0
[ 12.166351@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.172440@4] audio_dsp: last mode 0,now 0
[ 12.177069@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.182705@4] audio_dsp: last mode 0,now 0
[ 12.186881@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.192966@4] audio_dsp: last mode 0,now 0
[ 12.384177@4] tv_vout: vout [tv_set_vframe_rate_end_hint] return mode = 16, policy = 1!
[ 6.731186@3] fb: osd[0] canvas.width=7680
[ 6.735239@3] fb: osd[0] canvas.height=3240
[ 6.739409@3] fb: osd[0] frame.width=1920
[ 6.743348@3] fb: osd[0] frame.height=1080
[ 6.846369@7] fb: afbc: 1
[ 6.847029@7] fb: use ion buffer for fb memory
[ 6.847845@7] meson-fb meson-fb.16: create ion_client ffffffc063ec8c00, handle=ffffffc063882b40
[ 6.855875@4] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 6.862154@7] meson-fb meson-fb.16: ion memory(1): created fb at 0x000000007ab51000, size 1 MiB
[ 6.870677@7] fb: Frame buffer memory assigned at
[ 6.875125@7] fb: 1, phy: 0x000000007ab51000, vir:0xffffff8004aff000, size=1024K
[ 6.875125@7]
[ 6.884393@7] fb: fb1 open, logo index:1
[ 6.937261@0] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 7.039636@7] fb: osd[1] enable: 0 scale:0x0 (systemcontrol)
[ 7.039679@7] fb: osd[0] enable: 1 scale:0x10001 (systemcontrol)
[ 7.046066@7] fb: free_scale_switch to fb0, mode: 0x10001
[ 7.051283@7] vout_serve: osd0=> x:0,y:0,w:1920,h:1080
[ 7.051283@7] osd1=> x:0,y:0,w:18,h:18
[ 7.059821@7] fb: current vmode=1080p60hz
[ 7.079675@7] fb: osd[1] set scale, h_scale: ENABLE, v_scale: ENABLE
[ 7.080390@7] fb: osd[1].scaledata: 1920 1920 1080 1080
[ 7.085579@7] fb: osd[1].pandata: 0 0 0 0
[ 7.091298@4] healthd: No charger supplies found
[ 7.094393@4] healthd: No battery devices found
[ 8.288637@6] random: nonblocking pool is initialized
[ 11.332230@1] request_suspend_state: wakeup (3->0) at 11236701713 (2015-01-01 00:00:14.525460961 UTC)
[ 11.335790@1] request_suspend_state,168,old_sleep=0,new_state=0
[ 12.109135@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.109762@3] audio_dsp: last mode 0,now 0
[ 12.113884@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.120100@3] audio_dsp: last mode 0,now 0
[ 12.125029@5] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.130356@1] audio_dsp: last mode 0,now 0
[ 12.134451@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.140634@1] audio_dsp: last mode 0,now 0
[ 12.161544@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.162176@4] audio_dsp: last mode 0,now 0
[ 12.166351@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.172440@4] audio_dsp: last mode 0,now 0
[ 12.177069@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.182705@4] audio_dsp: last mode 0,now 0
[ 12.186881@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 12.192966@4] audio_dsp: last mode 0,now 0
[ 12.384177@4] tv_vout: vout [tv_set_vframe_rate_end_hint] return mode = 16, policy = 1!
[ 16.384100@4] lowmemorykiller: lowmem_shrink: convert oom_adj to oom_score_adj:
[ 16.385830@4] lowmemorykiller: oom_adj 0 => oom_score_adj 0
[ 16.391288@4] lowmemorykiller: oom_adj 2 => oom_score_adj 117
[ 16.397072@5] lowmemorykiller: oom_adj 4 => oom_score_adj 235
[ 16.402685@5] lowmemorykiller: oom_adj 6 => oom_score_adj 352
[ 16.408483@4] lowmemorykiller: oom_adj 9 => oom_score_adj 529
[ 16.414093@4] lowmemorykiller: oom_adj 15 => oom_score_adj 1000
[ 71.641374@4] dhd_module_init: in
[ 71.641430@4] ======== bcm_wlan_set_plat_data ========
[ 71.644158@4] host_oob_irq: 100
[ 71.647351@4] host_oob_irq_flags=0x414
[ 71.650976@4] dhd_wifi_platform_load: Enter
[ 71.655136@4] Power-up adapter 'DHD generic adapter'
[ 71.660070@4] wifi_platform_set_power = 1
[ 71.664036@0] ======== PULL WL_REG_ON HIGH! ========
[ 71.669024@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 71.876243@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 72.069396@4] avc open
[ 72.069430@4] amvenc_avc check CMA pool sucess, max instance: 2.
[ 72.072198@4] allocating phys 0x75200000, size 20480k, wq:ffffffc05ce71400.
[ 72.079129@4] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc05ce71400.
[ 72.089188@2] avc release, wq:ffffffc05ce71400
[ 72.093406@2] remove encode_work_queue ffffffc05ce71400 sucess, _destroy_encode_work_queue line 4285.
[ 72.104812@2] ionvid: info: ionvideo open
[ 72.305588@0] ionvid: info: ionvideo_stop_generating!!!!
[ 72.305659@0] ionvid: info: ionvideo release
[ 72.312500@6] ionvid: info: ionvideo open
[ 72.385645@0] wifi_platform_bus_enumerate device present 1
[ 72.385709@0] ======== Card detection to detect SDIO card! ========
[ 72.424259@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 72.427037@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 72.432712@6] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 72.440276@7] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 72.505593@6] ionvid: info: ionvideo_stop_generating!!!!
[ 72.505658@6] ionvid: info: ionvideo release
[ 72.512336@5] ionvid: info: ionvideo open
[ 72.538429@6] sdio: clk 200000000 SDR mode tuning start
[ 72.538740@6] sdio: rx_tuning_result[0] = 10
[ 72.542568@4] sdio: rx_tuning_result[1] = 10
[ 72.546898@4] sdio: rx_tuning_result[2] = 10
[ 72.551028@4] sdio: rx_tuning_result[3] = 10
[ 72.555027@4] sdio: best_win_start =0, best_win_size =4
[ 72.560391@4] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 72.567509@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 72.578817@0] sdio: queuing unknown CIS tuple 0x91 (3 bytes)
[ 72.579246@0] sdio: new ultra high speed SDR104 SDIO card at address 0001
[ 72.586133@0] sdio: clock 200000000, 4-bit-bus-width
[ 72.592483@6] [sdio_reinit] finish
[ 72.611435@5] bcmsdh_register: register client driver
[ 72.611610@6] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[ 72.615947@6] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[ 72.620698@6] bus num (host idx)=0, slot num (rca)=1
[ 72.625625@6] found adapter info 'DHD generic adapter'
[ 72.630729@6] Wifi: bcmdhd_mem_prealloc: 7 bcmdhd_mem_prealloc: wlan_mem_array[section].mem_ptr=ffffffc0020932e8, size=139264
[ 72.641974@6] success alloc section 3, size 139264
[ 72.646802@0] alloc static buf at ffffffc064780000!
[ 72.651627@0] Wifi: bcmdhd_mem_prealloc: 1 bcmdhd_mem_prealloc: section=4, wlan_static_skb=ffffffc002673368
[ 72.661493@0] success alloc section 4, size 0
[ 72.665825@1] sdioh_attach: set sd_f2_blocksize 128
[ 72.670703@1] dhdsdio_probe : no mutex held. set lock
[ 72.675465@1] F1 signature read @0x18000000=0x15264345
[ 72.684512@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 72.688268@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 72.694045@2] Wifi: bcmdhd_mem_prealloc: 4 bcmdhd_mem_prealloc: section=7, wlan_mem_array[4]=ffffffc064488000
[ 72.703840@2] success alloc section 7, size 25992
[ 72.708526@2] dhd_conf_set_chiprev: chip=0x4345, chiprev=6
[ 72.713875@2] dhd_conf_set_conf_path_by_nv_path: config_path=/etc/wifi/6255/config.txt
[ 72.715596@5] ionvid: info: ionvideo_stop_generating!!!!
[ 72.715617@5] ionvid: info: ionvideo release
[ 72.718323@5] ionvid: info: ionvideo open
[ 72.736530@2] dhd_conf_read_config: kso_enable = 0
[ 72.739988@2] Wifi: bcmdhd_mem_prealloc: 7 bcmdhd_mem_prealloc: wlan_mem_array[section].mem_ptr=ffffffc0020932b8, size=10416
[ 72.751149@2] success alloc section 0, size 10416
[ 72.756511@2] Wifi: bcmdhd_mem_prealloc: 2 bcmdhd_mem_prealloc: section=5, wlan_static_scan_buf0=ffffffc064620000
[ 72.765913@2] success alloc section 5, size 65536
[ 72.770672@2] wl_create_event_handler(): thread:wl_event_handler:11f0 started
[ 72.770675@3] tsk Enter, tsk = 0xffffff800a8dba88
[ 72.782817@3] dhd_attach(): thread:dhd_watchdog_thread:11f3 started
[ 72.788618@0] dhd_attach(): thread:dhd_dpc:11f4 started
[ 72.788633@2] dhd_dpc_thread: set dpc_cpucore 0 from config.txt
[ 72.800018@1] dhd_attach(): thread:dhd_rxf:11f5 started
[ 72.804671@1] dhd_deferred_work_init: work queue initialized
[ 72.810385@1] Wifi: bcmdhd_mem_prealloc: 7 bcmdhd_mem_prealloc: wlan_mem_array[section].mem_ptr=ffffffc0020932c8, size=10396
[ 72.821522@1] success alloc section 1, size 10396
[ 72.826255@1] Wifi: bcmdhd_mem_prealloc: 7 bcmdhd_mem_prealloc: wlan_mem_array[section].mem_ptr=ffffffc0020932d8, size=65536
[ 72.837379@1] success alloc section 2, size 65536
[ 72.867024@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 72.867024@1] Compiled in drivers/net/wireless/bcmdhd
[ 72.874570@1] Register interface [wlan0] MAC: 44:2c:05:f5:4a:5a
[ 72.874570@1]
[ 72.879880@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 72.885960@1] bcmsdh_oob_intr_unregister: Enter
[ 72.890351@1] bcmsdh_oob_intr_unregister: irq is not registered
[ 72.896392@1] dhd_txglom_enable: enable 0
[ 72.900177@1] dhd_conf_set_txglom_params: swtxglom=0, txglom_ext=0
[ 72.905601@5] ionvid: info: ionvideo_stop_generating!!!!
[ 72.905632@5] ionvid: info: ionvideo release
[ 72.908119@4] ionvid: info: ionvideo open
[ 72.919812@1] dhd_conf_set_txglom_params: txglom_bucket_size=0
[ 72.925556@1] dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0, bus_txglom=0
[ 72.933475@1] dhd_conf_set_txglom_params: tx_in_rx=1, tx_max_offset=0
[ 72.939923@1] dhd_bus_devreset: WLAN OFF DONE
[ 72.944360@1] wifi_platform_set_power = 0
[ 72.948257@1] ======== PULL WL_REG_ON LOW! ========
[ 72.953053@1] dhdsdio_probe : the lock is released.
[ 72.958286@1] dhd_module_init: Exit err=0
[ 73.071373@0] dhd_open: Enter ffffffc05cf27000
[ 73.071422@0]
[ 73.071422@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 73.071422@0] Compiled in drivers/net/wireless/bcmdhd
[ 73.085576@1] wl_android_wifi_on in 1
[ 73.086246@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 73.092333@1] wifi_platform_set_power = 1
[ 73.094979@1] ======== PULL WL_REG_ON HIGH! ========
[ 73.100518@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 73.105583@4] ionvid: info: ionvideo_stop_generating!!!!
[ 73.105608@4] ionvid: info: ionvideo release
[ 73.109143@4] ionvid: info: ionvideo open
[ 73.305573@4] ionvid: info: ionvideo_stop_generating!!!!
[ 73.305661@4] ionvid: info: ionvideo release
[ 73.314893@4] ionvid: info: ionvideo open
[ 73.320412@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 73.505585@4] ionvid: info: ionvideo_stop_generating!!!!
[ 73.505656@4] ionvid: info: ionvideo release
[ 73.513559@4] ionvid: info: ionvideo open
[ 73.705577@4] ionvid: info: ionvideo_stop_generating!!!!
[ 73.705653@4] ionvid: info: ionvideo release
[ 73.718488@5] ionvid: info: ionvideo open
[ 73.825607@2] sdio_reset_comm():
[ 73.854563@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 73.857379@6] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 73.863936@6] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 73.871371@4] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 73.915615@5] ionvid: info: ionvideo_stop_generating!!!!
[ 73.915693@5] ionvid: info: ionvideo release
[ 73.922416@5] ionvid: info: ionvideo open
[ 73.982091@4] sdio: clk 200000000 SDR mode tuning start
[ 73.982396@4] sdio: rx_tuning_result[0] = 10
[ 73.986274@4] sdio: rx_tuning_result[1] = 10
[ 73.991113@7] sdio: rx_tuning_result[2] = 10
[ 73.994649@7] sdio: rx_tuning_result[3] = 10
[ 73.998821@3] sdio: best_win_start =0, best_win_size =4
[ 74.003765@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 74.011157@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 74.017385@3] sdioh_start: set sd_f2_blocksize 128
[ 74.022411@3]
[ 74.022411@3]
[ 74.022411@3] dhd_bus_devreset: == WLAN ON ==
[ 74.029827@3] F1 signature read @0x18000000=0x15264345
[ 74.039734@1] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 74.042135@1] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 74.048768@1] dhd_conf_read_config: kso_enable = 0
[ 74.052987@1] dhd_conf_set_fw_name_by_chip: firmware_path=/etc/wifi/6255/fw_bcm43455c0_ag.bin
[ 74.061523@1] dhdsdio_download_firmware: set use_rxchain 0
[ 74.066910@1] dhdsdio_download_firmware: set txglomsize 40
[ 74.072276@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 74.077798@1] Final fw_path=/etc/wifi/6255/fw_bcm43455c0_ag.bin
[ 74.083637@1] Final nv_path=/etc/wifi/6255/nvram.txt
[ 74.088579@1] Final conf_path=/etc/wifi/6255/config.txt
[ 74.115623@6] ionvid: info: ionvideo_stop_generating!!!!
[ 74.115694@6] ionvid: info: ionvideo release
[ 74.176004@6] NVRAM version: AP6255_NVRAM_V1.0_29052015
[ 74.176971@3] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[ 74.262026@7] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
[ 74.262867@5] bcmsdh_oob_intr_register: Enter
[ 74.266843@5] bcmsdh_oob_intr_register: HW_OOB enabled
[ 74.271803@5] bcmsdh_oob_intr_register OOB irq=100 flags=414
[ 74.277524@5] bcmsdh_oob_intr_register: enable_irq_wake
[ 74.282604@5] bcmsdh_oob_intr_register: enable_irq_wake failed with -6
[ 74.294391@0] dhd_conf_set_fw_int_cmd: set WLC_SET_BAND 142 0
[ 74.295758@1] dhd_preinit_ioctls: Set tcpack_sup_mode 0
[ 74.303417@0] Firmware up: op_mode=0x0005, MAC=44:2c:05:f5:4a:5a
[ 74.305974@0] dhd_conf_set_country: set country ALL, revision 38
[ 74.311871@0] dhd_conf_set_fw_string_struct_cmd: set country
[ 74.318053@0] CONFIG-ERROR) dhd_conf_set_fw_string_struct_cmd: country setting failed -2
[ 74.326755@0] Country code: US (US/0)
[ 74.330768@0] dhd_conf_set_fw_string_cmd: set roam_off 1
[ 74.336570@3] dhd_conf_set_fw_string_cmd: set txbf 1
[ 74.339860@3] CONFIG-ERROR) dhd_conf_set_fw_string_cmd: txbf setting failed -23
[ 74.354925@0] Firmware version = wl0: Aug 25 2015 18:58:57 version 7.45.69 (r581703) FWID 01-24037f6e
[ 74.358572@0] Driver: 1.201.59.6 (r506368)
[ 74.358572@0] Firmware: wl0: Aug 25 2015 18:58:57 version 7.45.69 (r581703) FWID 01-24037f6e
[ 74.372426@1] dhd_txglom_enable: enable 1
[ 74.375485@1] dhd_conf_set_txglom_params: swtxglom=0, txglom_ext=0
[ 74.382809@1] dhd_conf_set_txglom_params: txglom_bucket_size=0
[ 74.387533@1] dhd_conf_set_txglom_params: txglomsize=40, deferred_tx_len=40, bus_txglom=0
[ 74.395328@1] dhd_conf_set_txglom_params: tx_in_rx=1, tx_max_offset=0
[ 74.401751@1] dhd_conf_set_disable_proptx: set disable_proptx 0
[ 74.408408@1] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64
[ 74.415271@1] wl_android_wifi_on: Success
[ 74.443629@6] avc open
[ 74.443677@6] allocating phys 0x75200000, size 20480k, wq:ffffffc03d1ed000.
[ 74.447312@6] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc03d1ed000.
[ 74.457427@0] avc release, wq:ffffffc03d1ed000
[ 74.461933@0] remove encode_work_queue ffffffc03d1ed000 sucess, _destroy_encode_work_queue line 4285.
[ 74.491509@6] dhd_open: Exit ret=0
[ 74.752748@0] avc open
[ 74.752795@0] allocating phys 0x75200000, size 20480k, wq:ffffffc064516800.
[ 74.756448@0] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc064516800.
[ 74.766467@0] avc release, wq:ffffffc064516800
[ 74.770764@0] remove encode_work_queue ffffffc064516800 sucess, _destroy_encode_work_queue line 4285.
[ 74.781583@2] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 74.785665@2] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 74.795404@2] xhci-hcd xhci-hcd.0.auto: irq 62, io mem 0xc9000000
[ 74.800573@3] hub 1-0:1.0: USB hub found
[ 74.803268@3] hub 1-0:1.0: 3 ports detected
[ 74.807690@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 74.812987@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 74.821696@3] hub 2-0:1.0: USB hub found
[ 74.824643@3] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 74.833574@3] file system registered
[ 74.843095@3] ffs_data_put(): freeing
[ 74.884110@4] dig: isBootCompleted:1!
[ 74.885031@6] dig: setDataRoCount count:0!
[ 75.073823@3] avc open
[ 75.073869@3] allocating phys 0x75200000, size 20480k, wq:ffffffc0637c7400.
[ 75.077390@6] P2P interface registered
[ 75.081353@3] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc0637c7400.
[ 75.083978@0] WLC_E_IF: NO_IF set, event Ignored
[ 75.086124@7] P2P interface started
[ 75.099431@3] avc release, wq:ffffffc0637c7400
[ 75.103619@3] remove encode_work_queue ffffffc0637c7400 sucess, _destroy_encode_work_queue line 4285.
[ 75.126135@6] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 75.142131@1] dhd_pktfilter_offload_set: failed to add pktfilter 102 0 0 0 0xFFFFFF 0x01005E, retcode = -2
[ 75.159321@0] dhd_set_suspend: Remove extra suspend setting
[ 75.301702@7] hub 1-1:1.0: USB hub found
[ 75.301809@7] hub 1-1:1.0: 3
@DRSDavidSoft
Copy link

Hello Jten!!!

Does anyone have any idea what does that mean? :|

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment