Skip to content

Instantly share code, notes, and snippets.

@DieterReuter

DieterReuter/gist:940c35b16311804160138dde9bba4e7e

Created February 11, 2017 19:03
Show Gist options
  • Save DieterReuter/940c35b16311804160138dde9bba4e7e to your computer and use it in GitHub Desktop.
Save DieterReuter/940c35b16311804160138dde9bba4e7e to your computer and use it in GitHub Desktop.
Download ZIP
Beelink GT1, several Bootlogs
Raw
gistfile1.txt
This file has been truncated, but you can view the full file.
GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 272797
BL2 Built : 19:58:22, Aug 31 2016.
gxl g54c8aee - xiaobo.gu@droid05
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00015400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a9a00
NOTICE: BL3-1: v1.0(debug):2e39a99
NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
aml log : bl31 normal boot !
[Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
OPS=0x82
fc c2 9 21 fb ca c 14 7e b4 40 63 [0.517246 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gd267f87 (Nov 17 2016 - 19:17:36)
DRAM: 2 GiB
Relocation Offset is: 76ec9000
register usb cfg[0][1] = 0000000077f5f5d8
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073ec96b0
aml_priv->desc_buf = 0x0000000073ecb9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ece270,dt_addr=0000000073ed9270
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000080000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 80000000 1
13: data d7c00000 2c5400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=cold_boot
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 4 vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
rx version is 1.4 or below div=10
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[CANVAS]canvas init
[CANVAS]addr=0x3d851000 width=5760, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
get_cpu_id flag_12bit=1
SARADC open channel(0).
SARADC channel(0) is 0x17 (0x0~0x50).
detect upgrade key
InUsbBurn
noSof
card out
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
emmc/sd response timeout, cmd1, status=0x1ff2800
[MSG]mmcinfo failed!
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
emmc/sd response timeout, cmd1, status=0x1ff2800
(Re)start USB...
USB0: USB3.0 XHCI init start
Register 3000140 NbrPorts 3
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 4 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =73f4e440
copy done
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x02106540
Loading Ramdisk to 73b0b000, end 73eb6349 ... OK
Loading Device Tree to 000000001fff2000, end 000000001ffff1ca ... OK
signature:
fdt_instaboot: no instaboot image
Starting kernel ...
uboot time: 7351701 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-g223e67e (lhh@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Thu Nov 17 19:36:40 CST 2016
[ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000@0] no prop version_code
[ 0.000000@0] bootconsole [earlycon0] enabled
[ 0.000000@0] fdt Reserved memory table:
[ 0.000000@0] linux,di: 0x000000007d300000 - 0x000000007f100000 (30 MiB)
[ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007d300000, size 30 MiB
[ 0.000000@0] linux,ion-dev: 0x0000000079300000 - 0x000000007d300000 (64 MiB)
[ 0.000000@0] linux,ppmgr: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] linux,codec_mm_cma: 0x0000000067800000 - 0x0000000073800000 (192 MiB)
[ 0.000000@0] linux,picdec: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] Reserved memory: incorrect alignment of CMA region
[ 0.000000@0] linux,codec_mm_reserved: 0x0000000075200000 - 0x0000000079300000 (65 MiB)
[ 0.000000@0] fdt Reserved memory total: 354 MiB
[ 0.000000@0] cma: Reserved 8 MiB at 74800000
[ 0.000000@0] psci: probing function IDs from device-tree
[ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc07516e000 s19968 r8192 d20992 u49152
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 510280
[ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=disabled logo=osd1,loaded,0x3d800000,1080p60hz maxcpus=8 vout=1080p60hz,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 androidboot.firstboot=0 jtag=apao androidboot.hardware=amlogic mac=86:37:20:48:cb:3e androidboot.mac=86:37:20:48:cb:3e aml_dt=gxm_q201_2g recovery_part={recovery_part} recovery_offset={recovery_offset} aml_dt=gxm_q201_2g recovery_part={recovery_part} recovery_offset={recovery_offset}
[ 0.000000@0] logo: osd1
[ 0.000000@0] logo: loaded
[ 0.000000@0] logo: 0x3d800000
[ 0.000000@0] logo: 1080p60hz
[ 0.000000@0] vout_serve: 1080p60hz
[ 0.000000@0] vout_serve: enable: 1
[ 0.000000@0] logo: get hdmimode: 1080p60hz
[ 0.000000@0] logo: get cvbsmode: 576cvbs
[ 0.000000@0] tv_vout: cvbs performance line = 0
[ 0.000000@0] jtag: jtag select 2
[ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000@0] Memory: 1640852K/2077696K available (10612K kernel code, 1153K rwdata, 3884K rodata, 1263K init, 5869K bss, 436844K reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
[ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff80423cc800 ( 35 MB)
[ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc07f100000 ( 2033 MB)
[ 0.000000@0] .init : 0xffffffc001eaa000 - 0xffffffc001fe5e00 ( 1264 kB)
[ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001ea9334 ( 14501 kB)
[ 0.000000@0] .data : 0xffffffc001fe6000 - 0xffffffc002106540 ( 1154 kB)
[ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01ea8fff]
[ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000@0] arch_multi_cluster:1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[ 0.008244@0] meson_bc_timer: mclk->mux_reg =ffffff8000014990,mclk->reg =ffffff8000016994
[ 0.016824@0] Console: colour dummy device 80x25
[ 0.021095@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.031671@0] pid_max: default: 32768 minimum: 301
[ 0.036580@0] Security Framework initialized
[ 0.040786@0] SELinux: Initializing.
[ 0.044531@0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.051367@0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.061622@0] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
[ 0.065714@0] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
[ 0.072720@0] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
[ 0.079712@0] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
[ 0.090047@0] Initializing cgroup subsys debug
[ 0.091174@0] Initializing cgroup subsys freezer
[ 0.095843@0] ftrace: allocating 36489 entries in 143 pages
[ 0.149535@0] /cpus/cpu@0: Missing clock-frequency property
[ 0.149578@0] /cpus/cpu@1: Missing clock-frequency property
[ 0.155155@0] /cpus/cpu@2: Missing clock-frequency property
[ 0.160782@0] /cpus/cpu@3: Missing clock-frequency property
[ 0.166356@0] /cpus/cpu@100: Missing clock-frequency property
[ 0.172138@0] /cpus/cpu@101: Missing clock-frequency property
[ 0.177907@0] /cpus/cpu@102: Missing clock-frequency property
[ 0.183689@0] /cpus/cpu@103: Missing clock-frequency property
[ 0.189456@0] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 0.239800@0] Meson chip version = RevA (22:A - 82:0)
[ 0.258210@1] CPU1: Booted secondary processor
[ 0.278176@2] CPU2: Booted secondary processor
[ 0.298183@3] CPU3: Booted secondary processor
[ 0.318208@4] CPU4: Booted secondary processor
[ 0.338214@5] CPU5: Booted secondary processor
[ 0.358225@6] CPU6: Booted secondary processor
[ 0.378247@7] CPU7: Booted secondary processor
[ 0.378340@0] Brought up 8 CPUs
[ 0.407155@0] SMP: Total of 8 processors activated.
[ 0.421221@2] sched: registering cpufreq notifiers for scale-invariant loads
[ 0.422747@2] instabooting: 0
[ 0.434903@2] pinctrl core: initialized pinctrl subsystem
[ 0.435604@2] regulator-dummy: no parameters
[ 0.439868@2] NET: Registered protocol family 16
[ 0.446061@3] ramoops: using module parameters
[ 0.448777@2] console [pstore-1] enabled
[ 0.452087@2] pstore: Registered ramoops as persistent store backend
[ 0.458463@2] ramoops: attached 0x100000@0x7300000, ecc: 0/0
[ 0.465076@3] cpuidle: using governor menu
[ 0.468567@3] aml_vdac_init: module init
[ 0.472380@2] register canvas platform driver
[ 0.476705@2] register rdma platform driver
[ 0.482935@2] vdso: 2 pages (1 code, 1 data) at base ffffffc001ff0000
[ 0.487305@2] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.494647@2] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.501543@2] software IO TLB [mem 0x64400000-0x64800000] (4MB) mapped at [ffffffc064400000-ffffffc0647fffff]
[ 0.510526@2] Serial: AMBA PL011 UART driver
[ 0.515397@3] aml_i2c version: 20140813
[ 0.518969@3] i2c-core: driver [pmu4] using legacy resume method
[ 0.524857@3] codec_mm:codec_mm_module_init
[ 0.529193@2] aml_watch_point_probe, in
[ 0.533211@2] gxbb_mpll_clk: register mpll_clk_out0 success done
[ 0.538812@2] gxbb_mpll_clk: register mpll_clk_out1 success done
[ 0.544827@2] gxbb_mpll_clk: register mpll_clk_out2 success done
[ 0.551076@2] clk_sys: register PLL sys_pll success done
[ 0.556209@2] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
[ 0.561572@2] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
[ 0.566701@2] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
[ 0.572219@2] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
[ 0.578162@2] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
[ 0.584130@2] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
[ 0.589974@2] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
[ 0.595842@2] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
[ 0.601699@2] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
[ 0.607595@2] gxl_clk: clock initialization complete
[ 0.612769@2] clkmsr: Gxl msr_clk_reg0=ffffff800003c75c,msr_clk_reg2=ffffff800003e764
[ 0.623030@2] aml_iomap: amlogic iomap probe done
[ 0.625795@3] pinmux-gxl c1109880.pinmux: Init pinux probe!
[ 0.631751@3] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
[ 0.637950@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.645479@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ 0.653708@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.661572@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
domain-0 init dvfs: 4
domain-1 init dvfs: 4
[ 0.681725@2] codec_mm has 2 memory regions
[ 0.681795@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.688432@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.697010@2] codec_mm has 2 memory regions
[ 0.701103@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.709137@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.719682@2] vpu: driver version: v02
[ 0.721409@2] vpu: load vpu_clk: 666667000Hz(7)
[ 0.726027@2] vpu: vpu_probe OK
[ 0.730873@2] tv_vout: tvout_probe
[ 0.732505@2] tv_vout: major number 254 for disp
[ 0.737132@2] vout_notify: vout_register_server
[ 0.741695@2] tv_vout: register tv module server ok
[ 0.746707@2] tv_vout: tvout_probe OK
[ 0.750925@2] canvas_probe reg=00000000c8838000,size=400
[ 0.755631@2] canvas maped reg_base =ffffff800009a000
[ 0.764963@2] rdma_probe
[ 1.082728@1] bio: create slab <bio-0> at 0
[ 1.083913@0] SCSI subsystem initialized
[ 1.085838@0] usbcore: registered new interface driver usbfs
[ 1.091214@0] usbcore: registered new interface driver hub
[ 1.096659@1] usbcore: registered new device driver usb
[ 1.102732@0] i2c-gpio i2c_gpio.38: using pins 172 (SDA) and 173 (SCL)
[ 1.108441@0] Linux video capture interface: v2.00
[ 1.113569@0] pps_core: LinuxPPS API ver. 1 registered
[ 1.118278@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 1.127788@1] PTP clock support registered
[ 1.132478@0] hdmitx: system: amhdmitx_init
[ 1.135951@0] hdmitx: system: Ver: 2014May6
[ 1.140349@0] hdmitx: system: amhdmitx_probe
[ 1.144748@2] hdmitx: system: not find match init-data
[ 1.149618@2] hdmitx: system: not find match pwr-ctl
[ 1.154588@2] hdmitx hpd irq = 89
[ 1.158485@2] hdmitx20: Mapped PHY: 0xc0800000
[ 1.162467@2] hdmitx20: Mapped PHY: 0xc1104400
[ 1.166854@2] hdmitx20: Mapped PHY: 0xc8100000
[ 1.171300@2] hdmitx20: Mapped PHY: 0xc8834000
[ 1.175770@2] hdmitx20: Mapped PHY: 0xc883a000
[ 1.180224@2] hdmitx20: Mapped PHY: 0xc883c000
[ 1.184691@2] hdmitx20: Mapped PHY: 0xd0100000
[ 1.189156@2] hdmitx20: Mapped PHY: 0xda83a000
[ 1.193618@2] hdmitx: alread display in uboot 0x10
[ 1.198442@2] avmute set to 1
[ 1.201810@0] vout_serve: vout_init_module
[ 1.205651@0] tv_vout: tv_set_current_vmode[759]fps_target_mode=16
[ 1.211745@0] hdmitx: system: irq 80000002
[ 1.215932@0] tv_vout: mode is 16,sync_duration_den=1,sync_duration_num=60
[ 1.222762@0] tv_vout: already display in uboot
[ 1.227298@0] vout_serve: vinfo mode is: 1080p60hz
[ 1.232110@0] vout_serve: init mode 1080p60hz
[ 1.236639@2] vout_serve: create vout attribute OK
[ 1.241299@2] vout_serve: meson_vout_probe OK
[ 1.245904@3] logo: logo_init
[ 1.249045@3] osd_rdma: osd_rdma_init: rdma_table p=0x74841000,op=0x74841000 , v=0xffffff800009e000
[ 1.257785@3] osd_rdma: osd rdma request irq as second interrput function!
[ 1.265189@2] Advanced Linux Sound Architecture Driver Initialized.
[ 1.271676@2] Bluetooth: Core ver 2.18
[ 1.274851@3] NET: Registered protocol family 31
[ 1.279375@3] Bluetooth: HCI device and connection manager initialized
[ 1.285933@3] Bluetooth: HCI socket layer initialized
[ 1.291008@3] Bluetooth: L2CAP socket layer initialized
[ 1.296278@3] Bluetooth: SCO socket layer initialized
[ 1.301858@2] cfg80211: Calling CRDA to update world regulatory domain
[ 1.308007@3] NetLabel: Initializing
[ 1.311485@3] NetLabel: domain hash size = 128
[ 1.316022@3] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.321245@3] NetLabel: unlabeled traffic allowed by default
[ 1.329481@2] Switched to clocksource arch_sys_counter
[ 1.379307@2] [amlatvdemod..]aml_atvdemod_init.
[ 1.379445@2] NET: Registered protocol family 2
[ 1.383331@2] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.390413@2] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 1.397328@2] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.403937@2] TCP: reno registered
[ 1.407241@2] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 1.413494@2] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 1.420662@2] NET: Registered protocol family 1
[ 1.424927@2] RPC: Registered named UNIX socket transport module.
[ 1.430789@2] RPC: Registered udp transport module.
[ 1.435670@2] RPC: Registered tcp transport module.
[ 1.440582@2] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.447446@2] aml_wifi wifi.33: [wifi_dev_probe] no power_on_pin2
[ 1.453357@2] aml_wifi wifi.33: [wifi_dev_probe] set pwm as 32k output
[ 1.460000@2] aml_wifi wifi.33: [wifi_dev_probe] dhd_static_buf setup
[ 1.466449@2] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem: WIFI MEM Allocated
[ 1.474031@2] aml_wifi wifi.33: [wifi_dev_probe] interrupt_pin=241
[ 1.480235@2] aml_wifi wifi.33: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
[ 1.487647@2] aml_wifi wifi.33: [wifi_dev_probe] power_on_pin=240
[ 1.493780@2] aml_wifi wifi.33: [wifi_dev_probe] clock_32k_pin=0
[ 1.500152@0] aml_wifi wifi.33: [wifi_setup_dt] wifi_setup_dt
[ 1.505621@0] aml_wifi wifi.33: [wifi_setup_dt] interrupt_pin(241)
[ 1.511825@0] aml_wifi wifi.33: [wifi_setup_dt] power_on_pin(240)
[ 1.518330@2] Unpacking initramfs...
[ 1.539613@0] hdmitx: plugin
[ 1.656029@3] Freeing initrd memory: 3756K (ffffffc073b0b000 - ffffffc073eb6000)
[ 1.663258@3] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 1.664454@3] audit: initializing netlink subsys (disabled)
[ 1.670046@3] audit: type=2000 audit(1.570:1): initialized
[ 1.676361@3] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.676436@0] hdmitx: edid: check sum valid
[ 1.676438@0] hdmitx: edid: check sum valid
[ 1.676441@0] hdmitx: edid: blk0 raw data
[ 1.676480@0] 00ffffffffffff001e6de37689bb02000b18010380502278eaca95a6554ea126
[ 1.676480@0] 0f50542108007140818081c0a9c0b300d1c0810001019d6770a0d0a022503020
[ 1.676480@0] 3a00204f3100001a000000fd00383d1e5a1e000a202020202020000000fc004c
[ 1.676480@0] 4720554c545241574944450a000000000000000000000000000000000000017c
[ 1.676480@0]
[ 1.676480@0]
[ 1.676482@0] hdmitx: edid: blk1 raw data
[ 1.676520@0] 020317f14410040301230907078301000065030c0010009f3d70a0d0a0155030
[ 1.676520@0] 203a00204f3100001a7e4800e0a0381f4040403a00204f31000018011d007251
[ 1.676520@0] d01e206e285500204f3100001e8c0ad08a20e02d10103e9600204f3100001800
[ 1.676520@0] 0000ff003431314b4b484e35393038310a0000000000000000000000000000ce
[ 1.676520@0]
[ 1.676520@0]
[ 1.676523@0] EDID Parser:
[ 1.676568@0] hdmitx: edid: find IEEEOUT
[ 1.676591@0]
[ 1.676593@0] hdmitx: edid: check sum valid
[ 1.676594@0] hdmitx: edid: check sum valid
[ 1.676598@0] hdmitx: update RX hdr info 0
[ 1.678621@0] hdmitx: ddc rd8b error 0x3a 0x00 0x00
[ 1.680666@0] [RX]-receive ksv list len:1,depth:1,cas:0,dev:0
[ 1.680672@0] hdmitx: video: get current mode: 1080p60hz
[ 1.680673@0] hdmitx: update rx hdr info 0
[ 1.680690@0] hdmitx: get ext_name (null)
[ 1.680696@0] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 16
[ 1.680701@0] hdmtix: set audio
[ 1.680710@0] hdmitx tx_aud_src = 0
[ 1.680738@0] hdmitx: fs = 0, cd = 4, tmds_clk = 148500
[ 1.680740@0] hdmitx aud_n_para = 6144
[ 1.680759@0] hdmitx set channel status
[ 1.842106@2] VFS: Disk quotas dquot_6.5.2
[ 1.842398@3] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.852605@2] NFS: Registering the id_resolver key type
[ 1.852671@2] Key type id_resolver registered
[ 1.856913@2] Key type id_legacy registered
[ 1.861156@2] NTFS driver 2.1.30 [Flags: R/O].
[ 1.866005@3] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.873691@3] fuse init (API version 7.22)
[ 1.877640@3] msgmni has been set to 3612
[ 1.882845@2] NET: Registered protocol family 38
[ 1.885996@3] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 1.893255@3] io scheduler noop registered
[ 1.897338@3] io scheduler deadline registered
[ 1.902145@2] io scheduler cfq registered (default)
[ 1.955215@2] meson-rng c8834000.rng: hwrng registered
[ 1.958865@2] loop: module loaded
[ 1.959534@2] zram: Created 1 device(s) ...
[ 1.963424@2] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.970742@3] tun: Universal TUN/TAP device driver, 1.6
[ 1.974229@3] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 2.106766@2] libphy: stmmac: probed
[ 2.106803@2] eth0: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[ 2.111357@2] eth0: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07)
[ 2.117798@2] PPP generic driver version 2.4.2
[ 2.122002@3] PPP BSD Compression module registered
[ 2.126651@3] PPP Deflate Compression module registered
[ 2.131940@3] PPP MPPE Compression module registered
[ 2.136887@3] NET: Registered protocol family 24
[ 2.141761@2] usbcore: registered new interface driver asix
[ 2.147296@2] usbcore: registered new interface driver ax88179_178a
[ 2.153620@3] usbcore: registered new interface driver cdc_ether
[ 2.159606@3] usbcore: registered new interface driver net1080
[ 2.165446@2] usbcore: registered new interface driver cdc_subset
[ 2.171622@3] usbcore: registered new interface driver zaurus
[ 2.177372@3] usbcore: registered new interface driver cdc_ncm
[ 2.183473@2] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.189854@2] ehci-h20ahb: H20AHB-EHCI Host Controller driver
[ 2.195889@3] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.202473@2] usbcore: registered new interface driver cdc_acm
[ 2.207852@2] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.216269@3] usbcore: registered new interface driver usb-storage
[ 2.222604@2] usbcore: registered new interface driver usbserial
[ 2.229082@3] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff80000da000
[ 2.239340@3] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
[ 2.245862@3] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff80000ee080
[ 2.257260@3] mousedev: PS/2 mouse device common for all mice
[ 2.262834@3] usbcore: registered new interface driver xpad
[ 2.268097@2] i2c /dev entries driver
[ 2.271978@2] usbcore: registered new interface driver uvcvideo
[ 2.277501@2] USB Video Class driver (1.1.1)
[ 2.282803@2] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: [email protected]
[ 2.290588@2] Bluetooth: HCI UART driver ver 2.2
[ 2.295089@2] Bluetooth: HCI H4 protocol initialized
[ 2.300479@2] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
[ 2.307837@0] cpu cpu4: bL_cpufreq_init: CPU 4 initialized
[ 2.311339@0] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
[ 2.319128@2] CPUidle arm64: cpuidle init start!!
[ 2.324411@2] @@@@@@@@@@_____2______in dia_init()
[ 2.328253@2] ATVR driver - init called!
[ 2.332326@3] usbcore: registered new interface driver usbhid
[ 2.337961@3] usbhid: USB HID core driver
[ 2.342385@2] ashmem: initialized
[ 2.345464@3] logger: created 256K log 'log_main'
[ 2.350233@3] logger: created 256K log 'log_events'
[ 2.355084@2] logger: created 256K log 'log_radio'
[ 2.359917@3] logger: created 256K log 'log_system'
[ 2.365815@3] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff80000fc4c0
[ 2.371865@3] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
[ 2.386877@3] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
[ 2.389513@3] console [ttyS0] enabled
[ 2.389513@3] console [ttyS0] enabled
[ 2.396745@3] bootconsole [earlycon0] disabled
[ 2.396745@3] bootconsole [earlycon0] disabled
[ 2.405958@2] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff80000fe4c0
[ 2.412611@2] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
[ 2.422353@3] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff]
[ 2.431787@3] meson-gpu-clkgen: probe of c883c000.gpu_clk failed with error -16
[ 2.439267@2] hdmitx: system: hdmitx_hdcp_init
[ 2.443613@2] ESM HLD: Initializing...
[ 2.447116@2] ESM HLD: Registering device range 'esm'...
[ 2.452391@2] ESM HLD: Device range 'esm' has been registered.
[ 2.458154@2] ESM HLD: Creating class /sys/class/elliptic...
[ 2.463877@3] ESM HLD: The class /sys/class/elliptic has been created.
[ 2.470237@3] ESM HLD: Creating device 'esm'...
[ 2.474839@2] ESM HLD: Device 'esm' has been created.
[ 2.479752@2] ESM HLD: Done initializing the HLD driver.
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[ 2.500968@2] aml_vrtc rtc.32: rtc core: registered aml_vrtc as rtc0
[ 2.502381@2] secmon has 1 memory regions
[ 2.505681@2] secmon: share in base: 0xffffff800011a000, share out base: 0xffffff800011c000
[ 2.513956@2] secmon secmon.4: assigned reserved memory node linux,secmon ok
[ 2.520916@2] secmon: probe done
[ 2.524438@2] storage: storage in base: 0xffffff8001800000
[ 2.529550@2] storage: storage out base: 0xffffff8001880000
[ 2.535054@2] storage: storage block base: 0xffffff8001900000
[ 2.540753@2] storage: probe done!
[ 2.544654@2] aml_sd_emmc_probe: line 3558
[ 2.548168@2] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
[ 2.558088@2] aml_sd_emmc_reg_init 1146
[ 2.561440@2] get property: ocr_avail, value:0x00200080
[ 2.567831@2] get property: f_min, value:300000
[ 2.573969@2] get property: f_max, value:100000000
[ 2.580343@2] get property: max_req_size, value:0x00020000
[ 2.586810@2] get property: pinname, str:emmc
[ 2.592591@2] get property: card_type, value:1
[ 2.598293@2] get property: gpio_dat3, str:
[ 2.603728@2] get property: hw_reset, str:
[ 2.609174@2] emmc:pdata->caps = c0000d47
[ 2.613121@2] emmc:pdata->caps2 = 18060
[ 2.616919@2] storage 1, boot 1
[ 2.620022@2] get_storage_dev return 1
[ 2.659493@3] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.659717@3] aml_sd_emmc_probe: line 3558
[ 2.664137@3] aml_sd_emmc_reg_init 1146
[ 2.667584@3] get property: ocr_avail, value:0x00200080
[ 2.674019@3] get property: f_min, value:400000
[ 2.680134@3] get property: f_max, value:100000000
[ 2.686511@3] get property: max_req_size, value:0x00020000
[ 2.692985@3] get property: irq_in, value:3
[ 2.698671@3] get property: irq_out, value:5
[ 2.704379@3] get property: gpio_cd, str:
[ 2.709804@3] get property: pinname, str:sd
[ 2.715405@3] get property: jtag_pin, str:
[ 2.720846@3] get property: card_type, value:5
[ 2.726532@3] get property: gpio_dat3, str:
[ 2.731981@3] sd:pdata->caps = 7
[ 2.735155@3] sd:pdata->caps2 = 0
[ 2.769687@3] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.769727@4] [aml_is_card_insert] card OUT
[ 2.769803@5] [aml_is_card_insert] card OUT
[ 2.778191@3] aml_sd_emmc_probe: line 3558
[ 2.782579@3] aml_sd_emmc_reg_init 1146
[ 2.786058@3] get property: ocr_avail, value:0x00200080
[ 2.792488@3] get property: f_min, value:400000
[ 2.798601@3] get property: f_max, value:200000000
[ 2.804989@3] get property: max_req_size, value:0x00020000
[ 2.811460@3] get property: pinname, str:sdio
[ 2.817232@3] get property: card_type, value:3
[ 2.822968@3] sdio:pdata->caps = 7810f
[ 2.826632@3] sdio:pdata->caps2 = 0
[ 2.866242@1] emmc: BKOPS_EN bit is not set
[ 2.869497@2] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.870936@1] ion_dev has 1 memory regions
[ 2.875905@1] emmc: trying cali 0-th time(s)
[ 2.882652@1] emmc: delay[0]= 4400 padding= 3, bidx=4
[ 2.883851@1] emmc: delay[1]= 4400 padding= 3, bidx=4
[ 2.888852@1] emmc: delay[2]= 4400 padding= 3, bidx=4
[ 2.890887@2] fb: osd_init_module
[ 2.891034@2] fb: viu vsync irq: 35
[ 2.891040@2] fb: failed to init reserved memory
[ 2.891052@2] fb: osd_probe vinfo:ffffffc002086d98
[ 2.891057@2] fb: init fbdev bpp is:32
[ 2.913631@1] emmc: delay[3]= 4600 padding= 2, bidx=4
[ 2.918615@1] emmc: delay[4]= 4600 padding= 2, bidx=4
[ 2.918621@1] emmc: delay[5]= 4600 padding= 2, bidx=4
[ 2.918623@1] emmc: delay[6]= 4400 padding= 3, bidx=4
[ 2.918625@1] emmc: delay[7]= 4800 padding= 1, bidx=4
[ 2.918627@1] emmc: calibration result @ 0: max(4800), min(4400)
[ 2.918630@1] emmc: line_delay =0x2111222, max_cal_result =4800
[ 2.918632@1] emmc: base_index_max 4, base_index_min 4
[ 2.918638@1] emmc: clk 100000000 SDR mode tuning start
[ 2.919376@1] emmc: rx_tuning_result[0] = 10
[ 2.919911@1] emmc: rx_tuning_result[1] = 10
[ 2.920444@1] emmc: rx_tuning_result[2] = 10
[ 2.920975@1] emmc: rx_tuning_result[3] = 10
[ 2.921506@1] emmc: rx_tuning_result[4] = 10
[ 2.922038@1] emmc: rx_tuning_result[5] = 10
[ 2.922567@1] emmc: rx_tuning_result[6] = 10
[ 2.923098@1] emmc: rx_tuning_result[7] = 10
[ 2.923630@1] emmc: rx_tuning_result[8] = 10
[ 2.923683@1] emmc: best_win_start =0, best_win_size =9
[ 2.923685@1] emmc: sd_emmc_regs->gclock=0x100024a,sd_emmc_regs->gadjust=0x42000
[ 2.923689@1] emmc: gclock =0x100024a, gdelay=0x2111222, gadjust=0x42000
[ 2.924015@1] emmc: new HS200 MMC card at address 0001
[ 2.924436@3] emmc: clock 100000000, 8-bit-bus-width
[ 2.924436@3]
[ 2.924437@3] mmcblk0: emmc:0001 NCard 14.4 GiB
[ 2.924567@3] mmcblk0boot0: emmc:0001 NCard partition 1 4.00 MiB
[ 2.924683@3] mmcblk0boot1: emmc:0001 NCard partition 2 4.00 MiB
[ 2.924807@3] mmcblk0rpmb: emmc:0001 NCard partition 3 4.00 MiB
[ 2.925419@1] mmcblk0: unknown partition table
[ 2.926158@3] [mmc_read_partition_tbl] mmc read partition OK!
[ 2.926159@3] add_emmc_partition
[ 2.926341@1] [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
[ 2.926484@3] [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
[ 2.926615@1] [mmcblk0p03] cache offset 0x000006c00000, size 0x000020000000
[ 2.926740@3] [mmcblk0p04] env offset 0x000027400000, size 0x000000800000
[ 2.926863@1] [mmcblk0p05] logo offset 0x000028400000, size 0x000002000000
[ 2.926986@3] [mmcblk0p06] recovery offset 0x00002ac00000, size 0x000002000000
[ 2.927117@1] [mmcblk0p07] rsv offset 0x00002d400000, size 0x000000800000
[ 2.927238@3] [mmcblk0p08] tee offset 0x00002e400000, size 0x000000800000
[ 2.927358@1] [mmcblk0p09] crypt offset 0x00002f400000, size 0x000002000000
[ 2.927480@3] [mmcblk0p10] misc offset 0x000031c00000, size 0x000002000000
[ 2.927606@1] [mmcblk0p11] instaboot offset 0x000034400000, size 0x000020000000
[ 2.927730@3] [mmcblk0p12] boot offset 0x000054c00000, size 0x000002000000
[ 2.927857@1] [mmcblk0p13] system offset 0x000057400000, size 0x000080000000
[ 2.927986@3] [mmcblk0p14] data offset 0x0000d7c00000, size 0x0002c5400000
[ 2.928015@3] card key: card_blk_probe.
[ 2.928019@3] emmc_key_init:527 emmc key lba_start:0x12020,lba_end:0x12220
[ 2.928021@3] emmc key: emmc_key_init:552 ok.
[ 2.928204@3] amlmmc_dtb_init: register dtb chardev
[ 2.928283@1] amlmmc_dtb_init: register dtb chardev OK
[ 2.928283@1] Exit aml_emmc_partition_ops OK.
[ 2.929319@3] mmcblk0boot1: unknown partition table
[ 2.930200@3] mmcblk0boot0: unknown partition table
[ 2.930472@1] clear_emmc_wait_flag
[ 3.230461@0] fb: osd probe OK
[ 3.230758@2] ge2d: ge2d_init_module
[ 3.231706@2] ge2d: ge2d_dev major:242
[ 3.235789@2] ge2d: ge2d clock is 400 MHZ
[ 3.239376@2] ge2d: ge2d: pdev=ffffffc06528a000, irq=182, rstc=0xffffffc0653b41c0, clk=ffffffc065278800
[ 3.248741@2] ge2d: mapped phy: 0xd0160000
[ 3.252751@2] ge2d: ge2d start monitor
[ 3.256492@1] ge2d: ge2d workqueue monitor start
[ 3.256725@2] sysled: module init
[ 3.256852@2] sysled: led_gpio = 154
[ 3.256853@2] sysled: active_low = 0
[ 3.257024@0] sysled: module probed ok
[ 3.257435@0] pwmled: module init
[ 3.257527@0] codec:Amlogic A/V streaming port init
[ 3.258898@2] codec:get gate demux control ok ffffffc0640ca5c0
[ 3.258902@2] codec:get gate parser_top control ok ffffffc0640ca640
[ 3.258906@2] codec:get gate vpu_intr control ok ffffffc0640ca6c0
[ 3.258912@2] codec:get gate vdec control ok ffffffc0640ca740
[ 3.259576@2] codec:[tsync_pcr_init]init success.
[ 3.259578@2] codec:amvideocap_init_module
[ 3.259719@2] codec:amvideocap_probe,amvideocap
[ 3.259722@2] codec:use cma buf.
[ 3.259724@2] codec:amvideocap_dev_register
[ 3.261556@0] amvenc_avc_probe -- reserved memory config fail.
[ 3.261559@0] amvenc_avc - cma memory pool size: 40 MB
[ 3.261581@0] encode_wq_init.
[ 3.261585@0] encode start monitor.
[ 3.261645@2] encode workqueue monitor start.
[ 3.262055@0] jpegenc module init
[ 3.262368@2] codec:picdec_driver_probe called.
[ 3.262371@2] picdec has 1 memory regions
[ 3.262398@2] codec:picdec_driver_probe done.
[ 3.263318@2] codec:create_ge2d_work_queue video task ok
[ 3.263699@0] codec:used fix clk for vdec clk source!
[ 3.263706@0] codec:register clk_set_setting cpu[34]
[ 3.264112@0] vpu_init
[ 3.264294@0] vpu_probe
[ 3.264299@0] HevcEnc reserved memory config fail.
[ 3.264304@0] HevcEnc - cma memory pool size: 64 MB
[ 3.264306@0] HevcEnc - wave420l_irq: 219
[ 3.264349@0] vpu base address get from platform driver physical base addr=0xc8810000, virtual base=0xffffff8000258000
[ 3.264652@0] success to probe vpu device with video memory from cma
[ 3.264805@2] DI: di_module_init ok.
[ 3.264809@2] DI: di_module_init: major 235
[ 3.265016@0] DI: di_probe
[ 3.265132@2] deinterlace has 1 memory regions
[ 3.265169@2] deinterlace deinterlace.26: assigned reserved memory node linux,di ok
[ 3.265190@2] di_irq:78,timerc_irq:38
[ 3.441487@2] rdma_register, rdma_table_addr ffffff800017b000 rdma_table_addr_phy 74848000 reg_buf ffffffc0637a6000
[ 3.451750@2] rdma_register success, handle 1 table_size 8192
[ 3.457413@2] DI: di_probe allocate rdma channel 1.
[ 3.462252@2] DI: DI hw version 2.
[ 3.465616@2] 0x000000db:Y=db,U=0,V=0
[ 3.469228@2] 0x000000dc:Y=dc,U=0,V=0
[ 3.473112@2] 0x000000dd:Y=dd,U=0,V=0
[ 3.476474@2] 0x000000de:Y=de,U=0,V=0
[ 3.480104@2] 0x000000df:Y=df,U=0,V=0
[ 3.483718@2] 0x000000e0:Y=e0,U=0,V=0
[ 3.487341@2] 0x000000e1:Y=e1,U=0,V=0
[ 3.490969@2] 0x000000e2:Y=e2,U=0,V=0
[ 3.494586@2] 0x000000e3:Y=e3,U=0,V=0
[ 3.498208@2] 0x000000f0:Y=f0,U=0,V=0
[ 3.501841@2] 0x000000f1:Y=f1,U=0,V=0
[ 3.505453@2] 0x000000f2:Y=f2,U=0,V=0
[ 3.509076@2] 0x000000f3:Y=f3,U=0,V=0
[ 3.512729@2] 0x000000f4:Y=f4,U=0,V=0
[ 3.516321@2] 0x000000f5:Y=f5,U=0,V=0
[ 3.519950@2] 0x000000f6:Y=f6,U=0,V=0
[ 3.523569@2] 0x000000f7:Y=f7,U=0,V=0
[ 3.527188@2] 0x000000f8:Y=f8,U=0,V=0
[ 3.530829@2] 0x000000f9:Y=f9,U=0,V=0
[ 3.534433@2] 0x000000fa:Y=fa,U=0,V=0
[ 3.538056@2] 0x000000fb:Y=fb,U=0,V=0
[ 3.541684@2] 0x000000fc:Y=fc,U=0,V=0
[ 3.545443@2] DI: di_probe here.
[ 3.548874@2] efusekeynum: 4
[ 3.551386@2] efusekeyname: mac offset: 0 size: 6
[ 3.557726@2] efusekeyname: mac_bt offset: 6 size: 6
[ 3.564125@2] efusekeyname: mac_wifi offset: 12 size: 6
[ 3.570508@2] efusekeyname: usid offset: 18 size: 16
[ 3.577154@1] efuse efuse.10: probe OK!
[ 3.581119@0] key unify config unifykey-num is 14
[ 3.585364@0] key unify fact unifykey-num is 14
[ 3.589828@0] aml_unifykeys_probe:1273=============unifykey_devno:e900000
[ 3.596809@1] 6unifykey: device unifykeys created ok
[ 3.601710@0] 6aml_unifykeys_init done!
[ 3.605419@0] PPMGRDRV: warn: ppmgr module init func called
[ 3.611111@0] PPMGRDRV: err: ppmgr_driver_probe called
[ 3.616075@0] ppmgr has 1 memory regions
[ 3.619951@0] PPMGRDRV: info: ppmgr_dev major:232
[ 3.624848@1] PPMGRDRV: info: ppmgr_probe done
[ 3.629406@0] amlogic rfkill init
[ 3.632485@0] enter bt_probe of_node
[ 3.635796@0] not get gpio_en
[ 3.638710@0] power on valid level is high
[ 3.642956@0] Bluetooth: BlueSleep Mode Driver Ver 1.2
[ 3.648424@0] ionvideo-000: V4L2 device registered as video13
[ 3.653584@0] ionvid: info: Video Technology Magazine Ion Video
[ 3.659410@0] ionvid: info: Capture Board ver 1.0 successfully loaded
[ 3.665859@0] audio_dsp: [dsp]register dsp to char divece(257)
[ 3.672307@0] amaudio: amaudio: driver amaudio succuess!
[ 3.677147@0] amlvid:err: amlvideo_init called
[ 3.681117@1] amlvid:err: amlvideo_create_instance called
[ 3.686580@1] amlvid:err: v4l2_dev.name=:amlvideo-000
[ 3.691772@0] amlvideo-000: V4L2 device registered as video10
[ 3.697739@1] vdin_drv_init: major 231
[ 3.701406@0] vdin_drv_init: vdin driver init done
[ 3.705732@0] tvafe_drv_init: major 230
[ 3.709939@0] tvafe: tvafe_init.
[ 3.713019@1] [RX]-hdmirx: hdmirx_init.
[ 3.716510@1] ESM HLD: Initializing...
[ 3.720251@1] ESM HLD: Registering device range 'esm_rx'...
[ 3.725744@1] ESM HLD: Device range 'esm_rx' has been registered.
[ 3.731781@1] ESM HLD: Creating class /sys/class/elliptic_rx...
[ 3.737753@0] ESM HLD: The class /sys/class/elliptic_rx has been created.
[ 3.744404@0] ESM HLD: Creating device 'esm_rx'...
[ 3.749308@0] ESM HLD: Device 'esm_rx' has been created.
[ 3.754386@0] ESM HLD: Done initializing the HLD driver.
[ 3.759647@0] [viuin..]viuin_init_module viuin module init
[ 3.765591@0] [viuin..]viuin_probe probe ok.
[ 3.769375@0] module init
[ 3.772057@0]
[ 3.772057@0] VECM probe start
[ 3.776934@0] aml_vecm_probe: ok
[ 3.780625@0] saradc c1108680.saradc: initialized by BL30
[ 3.785174@0] saradc c1108680.saradc: calibration start:
[ 3.790484@0] saradc c1108680.saradc: nominal=0, value=4
[ 3.795726@0] saradc c1108680.saradc: nominal=256, value=250
[ 3.801387@0] saradc c1108680.saradc: nominal=512, value=499
[ 3.806940@0] saradc c1108680.saradc: nominal=768, value=749
[ 3.812586@0] saradc c1108680.saradc: nominal=1023, value=997
[ 3.818228@0] saradc c1108680.saradc: calibration end: coef=4202
[ 3.824420@0] remote: Driver init
[ 3.827538@0] remote: platform_data g_remote_ao_offset=580
[ 3.832936@0] remote: platform_data irq =228
[ 3.837115@0] remote: set drvdata completed
[ 3.841339@0] remote: device_create_file completed
[ 3.846531@0] input: aml_keypad as /devices/meson-remote.12/input/input0
[ 3.853231@0] remote: input_register_device completed
[ 3.858101@0] remote: set_remote_mode[74]
[ 3.862035@0] remote: remote config major:227
[ 3.866656@0] remote: physical address:0x6402c000
[ 3.871758@0] gpio-key gpio_keypad.48: gpio_key: 0 name(power) pin()
[ 3.877369@0] gpio-key gpio_keypad.48: amlogic_gpio_name_map_num pin 0!::
[ 3.884187@0] gpio-key gpio_keypad.48: gpio_key: 0 power(147)
[ 3.889829@0] gpio-key gpio_keypad.48: start setup_timer
[ 3.895048@0] gpio-key gpio_keypad.48: power key(116) registed.
[ 3.901219@1] input: gpio_keypad as /devices/gpio_keypad.48/input/input1
[ 3.907703@0] gpio-key gpio_keypad.48: gpio keypad register input device completed.
[ 3.915218@0] input input1: gpio keypad major:226
[ 3.921109@0] Sensor: lsm303d_init
[ 3.923383@0] Sensor: stk8313_init
[ 3.926604@1] Sensor: stk831x_init
[ 3.930032@0] Sensor: mxc622x_acc_init
[ 3.933749@0] Sensor: mxc6255xc_acc_init
[ 3.937640@0] Sensor: l3gd20_gyr_init
[ 3.942127@0] aml dvb init
[ 3.944184@0] Amlogic Demod DVB-T/C DebugIF Init
[ 3.948627@1] Amlogic Demod DVB-T/C DebugIF Init ok----------------
[ 3.955586@1] jtag: module init
[ 3.957872@0] jtag: pinctrl setup apao
[ 3.961409@0] jtag: set state 2
efuse_pw_en: 0x3
WARNING! efuse bits is disabled
Enable A53 JTAG cluster 0 to AO
[ 3.977509@0] jtag: module probed ok
[ 3.977906@0] cpuinfo: probe done
[ 3.979132@1] defendkey c8834500.defendkey: defendkey_devno:de00000
[ 3.985362@0] defendkey c8834500.defendkey: defendkey: device defendkey created ok
[ 3.992565@0] input input1: key 116 up
[ 3.996561@1] defendkey: driver init
[ 4.000585@1] input: cec_input as /devices/virtual/input/input2
[ 4.005858@0] cectx aocec: no hdmirx reg resource
[ 4.010318@0] cectx aocec: no hhi reg resource
[ 4.014836@0] cectx aocec: can't find hdmirx
[ 4.019897@0] cec: wake up flag:0
[ 4.023098@0] aml_aes_dma c883e000.aml_aes: Aml AES_dma
[ 4.027963@1] aml_tdes_dma c883e000.aml_tdes: Aml TDES_dma
[ 4.033540@0] aml_sha_dma c883e000.aml_sha: Aml SHA1/SHA224/SHA256 dma
[ 4.039902@2] usbcore: registered new interface driver snd-usb-audio
[ 4.046951@2] aml_codec_T9015 c8832000.t9015: aml_T9015_audio_codec_probe
[ 4.054533@2] aml_pcm_dai: pcm mode detection =1
[ 4.057228@2] aml_spdif_dai: enterd aml_spdif_play,set_clock:-1,sample_rate=4
[ 4.064062@2] aml_spdif_dai: set normal 512 fs /4 fs
[ 4.068845@2] aml_audio_hw: IEC958 16bit
[ 4.072753@2] hdmitx: audio: aout notify rate 48000
[ 4.077550@2] hdmitx: audio: aout notify size 16
[ 4.082161@2] hdmitx: audio: aout notify format CT_PCM
[ 4.087211@2] hdmtix: set audio
[ 4.090343@2] hdmitx tx_aud_src = 0
[ 4.093790@2] hdmitx: fs = 3, cd = 4, tmds_clk = 148500
[ 4.098940@2] hdmitx aud_n_para = 6144
[ 4.102739@2] hdmitx set channel status
[ 4.106502@2] hdmitx: audio: Audio Type: PCM
[ 4.110687@2] hdmitx: audio: set audio param
[ 4.319699@3] aml_snd_card: headphone detection disable=1
[ 4.319735@3] aml_snd_card: no spk event delay time set
[ 4.325175@3] aml_snd_m8_card aml_m8_snd.47: T9015-audio-hifi <-> I2S.40 mapping ok
[ 4.332780@3] aml_snd_m8_card aml_m8_snd.47: dit-hifi <-> SPDIF.41 mapping ok
[ 4.339385@3] aml_pcm: enter aml_pcm_new dai->name: PCM.42 dai->id: 0
[ 4.345826@3] aml_snd_m8_card aml_m8_snd.47: pcm2bt-pcm <-> PCM.42 mapping ok
[ 4.352786@3] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTL
[ 4.360354@3] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
[ 4.369147@3] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTR
[ 4.376740@3] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
[ 4.387346@1] GACT probability NOT on
[ 4.389165@1] Mirror/redirect action on
[ 4.392970@1] u32 classifier
[ 4.395794@1] Actions configured
[ 4.399334@1] Netfilter messages via NETLINK v0.30.
[ 4.404226@1] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 4.410895@3] ctnetlink v0.93: registering with nfnetlink.
[ 4.416356@3] xt_time: kernel timezone is -0000
[ 4.420416@3] ipip: IPv4 over IPv4 tunneling driver
[ 4.425903@3] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 4.430716@3] arp_tables: (C) 2002 David S. Miller
[ 4.435362@3] TCP: cubic registered
[ 4.438747@3] Initializing XFRM netlink socket
[ 4.444106@1] NET: Registered protocol family 10
[ 4.448796@3] mip6: Mobile IPv6
[ 4.450866@3] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 4.456617@3] sit: IPv6 over IPv4 tunneling driver
[ 4.462507@3] NET: Registered protocol family 17
[ 4.465701@3] NET: Registered protocol family 15
[ 4.470405@3] Bridge firewalling registered
[ 4.474462@3] Bluetooth: RFCOMM TTY layer initialized
[ 4.479390@3] Bluetooth: RFCOMM socket layer initialized
[ 4.484701@3] Bluetooth: RFCOMM ver 1.11
[ 4.488520@3] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.493960@3] Bluetooth: BNEP filters: protocol multicast
[ 4.499307@3] Bluetooth: BNEP socket layer initialized
[ 4.504410@3] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 4.510433@3] Bluetooth: HIDP socket layer initialized
[ 4.515570@3] l2tp_core: L2TP core driver, V2.0
[ 4.520013@3] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 4.524911@3] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 4.530637@3] l2tp_netlink: L2TP netlink interface
[ 4.535384@3] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 4.541425@3] l2tp_debugfs: L2TP debugfs support
[ 4.545956@3] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 4.552565@3] NET: Registered protocol family 35
[ 4.557149@3] Key type dns_resolver registered
[ 4.563366@3] Registering SWP/SWPB emulation handler
[ 4.567179@3] regulator-dummy: disabling
[ 4.570744@3] aml_vrtc rtc.32: setting system clock to 2015-01-01 00:00:12 UTC (1420070412)
[ 4.580806@3] gxbb_pm: enter meson_pm_probe!
[ 4.582821@3] gxbb_pm: meson_pm_probe done
[ 4.587708@0] cpucore_cooling_register, max_cpu_core_num:4
[ 4.592558@0] cpucore_cooling_register, max_cpu_core_num:4
[ 4.613022@0] aml_istbt_dev_ready NULL
[ 4.61308 4.617768@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 4.621138@0] Freeing unused kernel memory: 1260K (ffffffc001eaa000 - ffffffc001fe5000)
[ 4.649643@0] init: init started!
[ 4.651144@0] init: init second stage started!
[ 4.652176@0] init: waitpid failed: No child processes
[ 4.657911@0] init: (Loading properties from /default.prop took 0.00s.)
[ 4.663923@0] init: /init.rc: 7: invalid command 'setcon'
[ 4.668795@0] init: /init.rc: 61: invalid command 'load_all_props'
[ 4.675035@0] init: (Parsing /init.recovery.amlogic.rc took 0.00s.)
[ 4.681179@0] init: (Parsing /init.rc took 0.02s.)
[ 4.685875@0] init: Starting service 'ueventd'...
[ 4.701078@2] ueventd: ueventd started!
[ 4.946417@2] ueventd: Coldboot took 0.24s.
[ 5.398728@0] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.398777@0] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 5.407356@0] xhci-hcd xhci-hcd.0.auto: irq 62, io mem 0xc9000000
[ 5.413272@0] hub 1-0:1.0: USB hub found
[ 5.416506@0] hub 1-0:1.0: 3 ports detected
[ 5.420813@0] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.426181@0] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 5.434598@0] hub 2-0:1.0: USB hub found
[ 5.437848@1] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 5.445742@1] init: Waiting for /dev/.coldboot_done...
[ 5.45 5.456510@1] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 5.470493@1] file system registered
[ 5.470778@1] init: write_file: Unable to write to '/sys/class/android_usb/android0/enable': No such device
[ 5.478213@1] init: write_file: Unable to open '/sys/class/android_usb/android0/f_ffs/aliases': No such file or directory
[ 5.489038@1] android_usb: Cannot enable 'adb' (-22)init: Starting service 'healthd'...
[ 5.497191@1] init: Starting service 'recovery'...
[ 5.501067@3] healthd: No charger supplies found
[ 5.501077@3] healthd: No battery devices found
[ 5.510998@1] in[ 5.517933@1] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 5.527865@1] systemcontrol: /etc/mesondisplay.cfg:12: Expected keyword, got '/etc/mesondisplay.cfg:12'.
[ 5.531938@1] vout_serve: vmode set to 1080p60hz
[ 5.536253@1] vout_serve: don't set the same mode as current
[ 5.544014@1] remote: cur_mode = 0
[ 5.545225@1] remote: set_remote_mode[74]
# [ 5.549781@3] fb: osd[0] enable: 0 (recovery)
[ 5.552467@2] remote: cur_mode = 0
[ 5.552473@2] remote: set_remote_mode[74]
[ 5.576473@2] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: discard
[ 5.613887@0] fb: osd[0] enable: 1 (recovery)
[ 5.630771@4] vout_serve: osd0=> x:0,y:0,w:1920,h:1080
[ 5.630771@4] osd1=> x:0,y:0,w:18,h:18
[ 5.638009@4] fb: current vmode=1080p60hz
[ 5.642128@4] fb: osd[1] set scale, h_scale: ENABLE, v_scale: ENABLE
[ 5.648268@4] fb: osd[1].scaledata: 1920 1920 1080 1080
[ 5.653454@4] fb: osd[1].pandata: 0 0 0 0
[ 5.663897@1] fb: osd[0] enable: 0 (recovery)
[ 5.680615@6] fb: osd[0] enable: 1 (recovery)
[ 5.739561@7] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 5.914416@7] hub 1-1:1.0: USB hub found
[ 5.914522@7] hub 1-1:1.0: 3 ports detected
[ 6.189545@5] usb 1-1.2: new low-speed USB device number 3 using xhci-hcd
[ 6.296562@5] usb 1-1.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.299989@5] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.409551@7] usb 1-1.3: new low-speed USB device number 4 using xhci-hcd
[ 6.514495@7] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.525787@6] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0003/input/input3
[ 6.533899@7] hid-generic 0003:046D:C05A.0003: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 10.594658@7] fb: use ion buffer for fb memory
[ 10.595382@7] meson-fb meson-fb.16: create ion_client ffffffc062a43c00, handle=ffffffc0633b5200
[ 10.602149@7] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 10.610818@7] fb: Frame buffer memory assigned at
[ 10.615295@7] fb: 0, phy: 0x0000000079300000, vir:0xffffff8001d75000, size=24900K
[ 10.615295@7]
[ 10.624617@7] fb: ---------------clear fb0 memory ffffff8001d75000
[ 10.640188@3] fb: osd[0] canvas.idx =0x40
[ 10.640213@3] fb: osd[0] canvas.addr=0x79300000
[ 10.643046@3] fb: osd[0] canvas.width=7680
[ 10.647100@3] fb: osd[0] canvas.height=3240
[ 10.651247@3] fb: osd[0] frame.width=1920
[ 10.655207@3] fb: osd[0] frame.height=1080
[ 10.699541@0] fb: osd[0] canvas.idx =0x40
[ 10.699543@0] fb: osd[0] canvas.addr=0x79300000
[ 10.699545@0] fb: osd[0] canvas.width=7680
[ 10.699546@0] fb: osd[0] canvas.height=2160
[ 10.699547@0] fb: osd[0] frame.width=1920
[ 10.699549@0] fb: osd[0] frame.height=1080
[ 10.732979@0] fb: osd[0] enable: 0 (recovery)
[ 10.747153@0] fb: osd[0] enable: 1 (recovery)
[ 26.559544@0] random: nonblocking pool is initialized
use] on usb-xhci-hcd.0.auto-1.3/input0
[ 10.594658@7] fb: use ion buffer for fb memory
[ 10.595382@7] meson-fb meson-fb.16: create ion_client ffffffc062a43c00, handle=ffffffc0633b5200
[ 10.602149@7] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 10.610818@7] fb: Frame buffer memory assigned at
[ 10.615295@7] fb: 0, phy: 0x0000000079300000, vir:0xffffff8001d75000, size=24900K
[ 10.615295@7]
[ 10.624617@7] fb: ---------------clear fb0 memory ffffff8001d75000
[ 10.640188@3] fb: osd[0] canvas.idx =0x40
[ 10.640213@3] fb: osd[0] canvas.addr=0x79300000
[ 10.643046@3] fb: osd[0] canvas.width=7680
[ 10.647100@3] fb: osd[0] canvas.height=3240
[ 10.651247@3] fb: osd[0] frame.width=1920
[ 10.655207@3] fb: osd[0] frame.height=1080
[ 10.699541@0] fb: osd[0] canvas.idx =0x40
[ 10.699543@0] fb: osd[0] canvas.addr=0x79300000
[ 10.699545@0] fb: osd[0] canvas.width=7680
[ 10.699546@0] fb: osd[0] canvas.height=2160
[ 10.699547@0] fb: osd[0] frame.width=1920
[ 10.699549@0] fb: osd[0] frame.height=1080
[ 10.732979@0] fb: osd[0] enable: 0 (recovery)
[ 10.747153@0] fb: osd[0] enable: 1 (recovery)
[ 26.559544@0] random: nonblocking pool is initialized
[ 6.533899@7] hid-generic 0003:046D:C05A.0003: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 10.594658@7] fb: use ion buffer for fb memory
[ 10.595382@7] meson-fb meson-fb.16: create ion_client ffffffc062a43c00, handle=ffffffc0633b5200
[ 10.602149@7] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 10.610818@7] fb: Frame buffer memory assigned at
[ 10.615295@7] fb: 0, phy: 0x0000000079300000, vir:0xffffff8001d75000, size=24900K
[ 10.615295@7]
[ 10.624617@7] fb: ---------------clear fb0 memory ffffff8001d75000
[ 10.640188@3] fb: osd[0] canvas.idx =0x40
[ 10.640213@3] fb: osd[0] canvas.addr=0x79300000
[ 10.643046@3] fb: osd[0] canvas.width=7680
[ 10.647100@3] fb: osd[0] canvas.height=3240
[ 10.651247@3] fb: osd[0] frame.width=1920
[ 10.655207@3] fb: osd[0] frame.height=1080
[ 10.699541@0] fb: osd[0] canvas.idx =0x40
[ 10.699543@0] fb: osd[0] canvas.addr=0x79300000
[ 10.699545@0] fb: osd[0] canvas.width=7680
[ 10.699546@0] fb: osd[0] canvas.height=2160
[ 10.699547@0] fb: osd[0] frame.width=1920
[ 10.699549@0] fb: osd[0] frame.height=1080
[ 10.732979@0] fb: osd[0] enable: 0 (recovery)
[ 10.747153@0] fb: osd[0] enable: 1 (recovery)
[ 26.559544@0] random: nonblocking pool is initialized
[ 6.514495@7] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.525787@6] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0003/input/input3
[ 6.533899@7] hid-generic 0003:046D:C05A.0003: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 10.594658@7] fb: use ion buffer for fb memory
[ 10.595382@7] meson-fb meson-fb.16: create ion_client ffffffc062a43c00, handle=ffffffc0633b5200
[ 10.602149@7] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 10.610818@7] fb: Frame buffer memory assigned at
[ 10.615295@7] fb: 0, phy: 0x0000000079300000, vir:0xffffff8001d75000, size=24900K
[ 10.615295@7]
[ 10.624617@7] fb: ---------------clear fb0 memory ffffff8001d75000
[ 10.640188@3] fb: osd[0] canvas.idx =0x40
[ 10.640213@3] fb: osd[0] canvas.addr=0x79300000
[ 10.643046@3] fb: osd[0] canvas.width=7680
[ 10.647100@3] fb: osd[0] canvas.height=3240
[ 10.651247@3] fb: osd[0] frame.width=1920
[ 10.655207@3] fb: osd[0] frame.height=1080
[ 10.699541@0] fb: osd[0] canvas.idx =0x40
[ 10.699543@0] fb: osd[0] canvas.addr=0x79300000
[ 10.699545@0] fb: osd[0] canvas.width=7680
[ 10.699546@0] fb: osd[0] canvas.height=2160
[ 10.699547@0] fb: osd[0] frame.width=1920
[ 10.699549@0] fb: osd[0] frame.height=1080
[ 10.732979@0] fb: osd[0] enable: 0 (recovery)
[ 10.747153@0] fb: osd[0] enable: 1 (recovery)
[ 26.559544@0] random: nonblocking pool is initialized
[ 6.299989@5] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.409551@7] usb 1-1.3: new low-speed USB device number 4 using xhci-hcd
[ 6.514495@7] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.525787@6] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0003/input/input3
[ 6.533899@7] hid-generic 0003:046D:C05A.0003: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 10.594658@7] fb: use ion buffer for fb memory
[ 10.595382@7] meson-fb meson-fb.16: create ion_client ffffffc062a43c00, handle=ffffffc0633b5200
[ 10.602149@7] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 10.610818@7] fb: Frame buffer memory assigned at
[ 10.615295@7] fb: 0, phy: 0x0000000079300000, vir:0xffffff8001d75000, size=24900K
[ 10.615295@7]
[ 10.624617@7] fb: ---------------clear fb0 memory ffffff8001d75000
[ 10.640188@3] fb: osd[0] canvas.idx =0x40
[ 10.640213@3] fb: osd[0] canvas.addr=0x79300000
[ 10.643046@3] fb: osd[0] canvas.width=7680
[ 10.647100@3] fb: osd[0] canvas.height=3240
[ 10.651247@3] fb: osd[0] frame.width=1920
[ 10.655207@3] fb: osd[0] frame.height=1080
[ 10.699541@0] fb: osd[0] canvas.idx =0x40
[ 10.699543@0] fb: osd[0] canvas.addr=0x79300000
[ 10.699545@0] fb: osd[0] canvas.width=7680
[ 10.699546@0] fb: osd[0] canvas.height=2160
[ 10.699547@0] fb: osd[0] frame.width=1920
[ 10.699549@0] fb: osd[0] frame.height=1080
[ 10.732979@0] fb: osd[0] enable: 0 (recovery)
[ 10.747153@0] fb: osd[0] enable: 1 (recovery)
[ 26.559544@0] random: nonblocking pool is initialized
[ 6.296562@5] usb 1-1.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.299989@5] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.409551@7] usb 1-1.3: new low-speed USB device number 4 using xhci-hcd
[ 6.514495@7] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.525787@6] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0003/input/input3
[ 6.533899@7] hid-generic 0003:046D:C05A.0003: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 10.594658@7] fb: use ion buffer for fb memory
[ 10.595382@7] meson-fb meson-fb.16: create ion_client ffffffc062a43c00, handle=ffffffc0633b5200
[ 10.602149@7] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 10.610818@7] fb: Frame buffer memory assigned at
[ 10.615295@7] fb: 0, phy: 0x0000000079300000, vir:0xffffff8001d75000, size=24900K
[ 10.615295@7]
[ 10.624617@7] fb: ---------------clear fb0 memory ffffff8001d75000
[ 10.640188@3] fb: osd[0] canvas.idx =0x40
[ 10.640213@3] fb: osd[0] canvas.addr=0x79300000
[ 10.643046@3] fb: osd[0] canvas.width=7680
[ 10.647100@3] fb: osd[0] canvas.height=3240
[ 10.651247@3] fb: osd[0] frame.width=1920
[ 10.655207@3] fb: osd[0] frame.height=1080
[ 10.699541@0] fb: osd[0] canvas.idx =0x40
[ 10.699543@0] fb: osd[0] canvas.addr=0x79300000
[ 10.699545@0] fb: osd[0] canvas.width=7680
[ 10.699546@0] fb: osd[0] canvas.height=2160
[ 10.699547@0] fb: osd[0] frame.width=1920
[ 10.699549@0] fb: osd[0] frame.height=1080
[ 10.732979@0] fb: osd[0] enable: 0 (recovery)
[ 10.747153@0] fb: osd[0] enable: 1 (recovery)
[ 26.559544@0] random: nonblocking pool is initialized
[ 5.914416@7] hub 1-1:1.0: USB hub found
[ 5.914522@7] hub 1-1:1.0: 3 ports detected
[ 6.189545@5] usb 1-1.2: new low-speed USB device number 3 using xhci-hcd
[ 6.296562@5] usb 1-1.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.299989@5] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.409551@7] usb 1-1.3: new low-speed USB device number 4 using xhci-hcd
[ 6.514495@7] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.525787@6] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0003/input/input3
[ 6.533899@7] hid-generic 0003:046D:C05A.0003: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 10.594658@7] fb: use ion buffer for fb memory
[ 10.595382@7] meson-fb meson-fb.16: create ion_client ffffffc062a43c00, handle=ffffffc0633b5200
[ 10.602149@7] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 10.610818@7] fb: Frame buffer memory assigned at
[ 10.615295@7] fb: 0, phy: 0x0000000079300000, vir:0xffffff8001d75000, size=24900K
[ 10.615295@7]
[ 10.624617@7] fb: ---------------clear fb0 memory ffffff8001d75000
[ 10.640188@3] fb: osd[0] canvas.idx =0x40
[ 10.640213@3] fb: osd[0] canvas.addr=0x79300000
[ 10.643046@3] fb: osd[0] canvas.width=7680
[ 10.647100@3] fb: osd[0] canvas.height=3240
[ 10.651247@3] fb: osd[0] frame.width=1920
[ 10.655207@3] fb: osd[0] frame.height=1080
[ 10.699541@0] fb: osd[0] canvas.idx =0x40
[ 10.699543@0] fb: osd[0] canvas.addr=0x79300000
[ 10.699545@0] fb: osd[0] canvas.width=7680
[ 10.699546@0] fb: osd[0] canvas.height=2160
[ 10.699547@0] fb: osd[0] frame.width=1920
[ 10.699549@0] fb: osd[0] frame.height=1080
[ 10.732979@0] fb: osd[0] enable: 0 (recovery)
[ 10.747153@0] fb: osd[0] enable: 1 (recovery)
[ 26.559544@0] random: nonblocking pool is initialized
[ 5.739561@7] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 5.914416@7] hub 1-1:1.0: USB hub found
[ 5.914522@7] hub 1-1:1.0: 3 ports detected
[ 6.189545@5] usb 1-1.2: new low-speed USB device number 3 using xhci-hcd
[ 6.296562@5] usb 1-1.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.299989@5] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.409551@7] usb 1-1.3: new low-speed USB device number 4 using xhci-hcd
[ 6.514495@7] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.525787@6] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0003/input/input3
[ 6.533899@7] hid-generic 0003:046D:C05A.0003: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 10.594658@7] fb: use ion buffer for fb memory
[ 10.595382@7] meson-fb meson-fb.16: create ion_client ffffffc062a43c00, handle=ffffffc0633b5200
[ 10.602149@7] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 10.610818@7] fb: Frame buffer memory assigned at
[ 10.615295@7] fb: 0, phy: 0x0000000079300000, vir:0xffffff8001d75000, size=24900K
[ 10.615295@7]
[ 10.624617@7] fb: ---------------clear fb0 memory ffffff8001d75000
[ 10.640188@3] fb: osd[0] canvas.idx =0x40
[ 10.640213@3] fb: osd[0] canvas.addr=0x79300000
[ 10.643046@3] fb: osd[0] canvas.width=7680
[ 10.647100@3] fb: osd[0] canvas.height=3240
[ 10.651247@3] fb: osd[0] frame.width=1920
[ 10.655207@3] fb: osd[0] frame.height=1080
[ 10.699541@0] fb: osd[0] canvas.idx =0x40
[ 10.699543@0] fb: osd[0] canvas.addr=0x79300000
[ 10.699545@0] fb: osd[0] canvas.width=7680
[ 10.699546@0] fb: osd[0] canvas.height=2160
[ 10.699547@0] fb: osd[0] frame.width=1920
[ 10.699549@0] fb: osd[0] frame.height=1080
[ 10.732979@0] fb: osd[0] enable: 0 (recovery)
[ 10.747153@0] fb: osd[0] enable: 1 (recovery)
[ 26.559544@0] random: nonblocking pool is initialized
[ 5.680615@6] fb: osd[0] enable: 1 (recovery)
[ 5.739561@7] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 5.914416@7] hub 1-1:1.0: USB hub found
[ 5.914522@7] hub 1-1:1.0: 3 ports detected
[ 6.189545@5] usb 1-1.2: new low-speed USB device number 3 using xhci-hcd
[ 6.296562@5] usb 1-1.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.299989@5] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.409551@7] usb 1-1.3: new low-speed USB device number 4 using xhci-hcd
[ 6.514495@7] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.525787@6] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0003/input/input3
[ 6.533899@7] hid-generic 0003:046D:C05A.0003: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 10.594658@7] fb: use ion buffer for fb memory
[ 10.595382@7] meson-fb meson-fb.16: create ion_client ffffffc062a43c00, handle=ffffffc0633b5200
[ 10.602149@7] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 10.610818@7] fb: Frame buffer memory assigned at
[ 10.615295@7] fb: 0, phy: 0x0000000079300000, vir:0xffffff8001d75000, size=24900K
[ 10.615295@7]
[ 10.624617@7] fb: ---------------clear fb0 memory ffffff8001d75000
[ 10.640188@3] fb: osd[0] canvas.idx =0x40
[ 10.640213@3] fb: osd[0] canvas.addr=0x79300000
[ 10.643046@3] fb: osd[0] canvas.width=7680
[ 10.647100@3] fb: osd[0] canvas.height=3240
[ 10.651247@3] fb: osd[0] frame.width=1920
[ 10.655207@3] fb: osd[0] frame.height=1080
[ 10.699541@0] fb: osd[0] canvas.idx =0x40
[ 10.699543@0] fb: osd[0] canvas.addr=0x79300000
[ 10.699545@0] fb: osd[0] canvas.width=7680
[ 10.699546@0] fb: osd[0] canvas.height=2160
[ 10.699547@0] fb: osd[0] frame.width=1920
[ 10.699549@0] fb: osd[0] frame.height=1080
[ 10.732979@0] fb: osd[0] enable: 0 (recovery)
[ 10.747153@0] fb: osd[0] enable: 1 (recovery)
[ 26.559544@0] random: nonblocking pool is initialized
[ 5.663897@1] fb: osd[0] enable: 0 (recovery)
[ 5.680615@6] fb: osd[0] enable: 1 (recovery)
[ 5.739561@7] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 5.914416@7] hub 1-1:1.0: USB hub found
[ 5.914522@7] hub 1-1:1.0: 3 ports detected
[ 6.189545@5] usb 1-1.2: new low-speed USB device number 3 using xhci-hcd
[ 6.296562@5] usb 1-1.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.299989@5] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.409551@7] usb 1-1.3: new low-speed USB device number 4 using xhci-hcd
[ 6.514495@7] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.525787@6] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0003/input/input3
[ 6.533899@7] hid-generic 0003:046D:C05A.0003: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 10.594658@7] fb: use ion buffer for fb memory
[ 10.595382@7] meson-fb meson-fb.16: create ion_client ffffffc062a43c00, handle=ffffffc0633b5200
[ 10.602149@7] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 10.610818@7] fb: Frame buffer memory assigned at
[ 10.615295@7] fb: 0, phy: 0x0000000079300000, vir:0xffffff8001d75000, size=24900K
[ 10.615295@7]
[ 10.624617@7] fb: ---------------clear fb0 memory ffffff8001d75000
[ 10.640188@3] fb: osd[0] canvas.idx =0x40
[ 10.640213@3] fb: osd[0] canvas.addr=0x79300000
[ 10.643046@3] fb: osd[0] canvas.width=7680
[ 10.647100@3] fb: osd[0] canvas.height=3240
[ 10.651247@3] fb: osd[0] frame.width=1920
[ 10.655207@3] fb: osd[0] frame.height=1080
[ 10.699541@0] fb: osd[0] canvas.idx =0x40
[ 10.699543@0] fb: osd[0] canvas.addr=0x79300000
[ 10.699545@0] fb: osd[0] canvas.width=7680
[ 10.699546@0] fb: osd[0] canvas.height=2160
[ 10.699547@0] fb: osd[0] frame.width=1920
[ 10.699549@0] fb: osd[0] frame.height=1080
[ 10.732979@0] fb: osd[0] enable: 0 (recovery)
[ 10.747153@0] fb: osd[0] enable: 1 (recovery)
[ 26.559544@0] random: nonblocking pool is initialized
[ 5.653454@4] fb: osd[1].pandata: 0 0 0 0
[ 5.663897@1] fb: osd[0] enable: 0 (recovery)
[ 5.680615@6] fb: osd[0] enable: 1 (recovery)
[ 5.739561@7] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 5.914416@7] hub 1-1:1.0: USB hub found
[ 5.914522@7] hub 1-1:1.0: 3 ports detected
[ 6.189545@5] usb 1-1.2: new low-speed USB device number 3 using xhci-hcd
[ 6.296562@5] usb 1-1.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.299989@5] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.409551@7] usb 1-1.3: new low-speed USB device number 4 using xhci-hcd
[ 6.514495@7] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.525787@6] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0003/input/input3
[ 6.533899@7] hid-generic 0003:046D:C05A.0003: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 10.594658@7] fb: use ion buffer for fb memory
[ 10.595382@7] meson-fb meson-fb.16: create ion_client ffffffc062a43c00, handle=ffffffc0633b5200
[ 10.602149@7] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 10.610818@7] fb: Frame buffer memory assigned at
[ 10.615295@7] fb: 0, phy: 0x0000000079300000, vir:0xffffff8001d75000, size=24900K
[ 10.615295@7]
[ 10.624617@7] fb: ---------------clear fb0 memory ffffff8001d75000
[ 10.640188@3] fb: osd[0] canvas.idx =0x40
[ 10.640213@3] fb: osd[0] canvas.addr=0x79300000
[ 10.643046@3] fb: osd[0] canvas.width=7680
[ 10.647100@3] fb: osd[0] canvas.height=3240
[ 10.651247@3] fb: osd[0] frame.width=1920
[ 10.655207@3] fb: osd[0] frame.height=1080
[ 10.699541@0] fb: osd[0] canvas.idx =0x40
[ 10.699543@0] fb: osd[0] canvas.addr=0x79300000
[ 10.699545@0] fb: osd[0] canvas.width=7680
[ 10.699546@0] fb: osd[0] canvas.height=2160
[ 10.699547@0] fb: osd[0] frame.width=1920
[ 10.699549@0] fb: osd[0] frame.height=1080
[ 10.732979@0] fb: osd[0] enable: 0 (recovery)
[ 10.747153@0] fb: osd[0] enable: 1 (recovery)
[ 26.559544@0] random: nonblocking pool is initialized
#
# poweroff
/sbin/sh: poweroff: not found
# [ 306.196623@4] [aml_is_card_insert] card IN
_ 306.297974@4] normal card in
[ 306.298122@5] [aml_is_card_insert] card IN
[ 306.299355@4] [aml_is_card_insert] card IN
[ 306.614720@5] sd: new high speed SDHC card at address aaaa
[ 306.614753@5] sd: clock 50000000, 4-bit-bus-width
[ 306.620131@5] mmcblk1: sd:aaaa SL08G 7.40 GiB
[ 306.634529@6] mmcblk1: p1
#
#
# GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 166868
BL2 Built : 19:58:22, Aug 31 2016.
gxl g54c8aee - xiaobo.gu@droid05
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00015400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a9a00
NOTICE: BL3-1: v1.0(debug):2e39a99
NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
aml log : bl31 normal boot !
[Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
OPS=0x82
fc c2 9 21 fb ca c 14 7e b4 40 63 [0.411309 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gd267f87 (Nov 17 2016 - 19:17:36)
DRAM: 2 GiB
Relocation Offset is: 76ec9000
register usb cfg[0][1] = 0000000077f5f5d8
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073ec96b0
aml_priv->desc_buf = 0x0000000073ecb9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ece270,dt_addr=0000000073ed9270
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000080000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 80000000 1
13: data d7c00000 2c5400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=cold_boot
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 4 vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
rx version is 1.4 or below div=10
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[CANVAS]canvas init
[CANVAS]addr=0x3d851000 width=5760, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
get_cpu_id flag_12bit=1
SARADC open channel(0).
SARADC channel(0) is 0x15 (0x0~0x50).
detect upgrade key
InUsbBurn
noSof
card in
[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
** Unrecognized filesystem type **
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
** Unrecognized filesystem type **
** Unrecognized filesystem type **
(Re)start USB...
USB0: USB3.0 XHCI init start
Register 3000140 NbrPorts 3
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 4 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =73f4e440
copy done
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x02106540
Loading Ramdisk to 73b0b000, end 73eb6349 ... OK
Loading Device Tree to 000000001fff2000, end 000000001ffff1ca ... OK
signature:
fdt_instaboot: no instaboot image
Starting kernel ...
uboot time: 7402250 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-g223e67e (lhh@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Thu Nov 17 19:36:40 CST 2016
[ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000@0] no prop version_code
[ 0.000000@0] bootconsole [earlycon0] enabled
[ 0.000000@0] fdt Reserved memory table:
[ 0.000000@0] linux,di: 0x000000007d300000 - 0x000000007f100000 (30 MiB)
[ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007d300000, size 30 MiB
[ 0.000000@0] linux,ion-dev: 0x0000000079300000 - 0x000000007d300000 (64 MiB)
[ 0.000000@0] linux,ppmgr: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] linux,codec_mm_cma: 0x0000000067800000 - 0x0000000073800000 (192 MiB)
[ 0.000000@0] linux,picdec: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] Reserved memory: incorrect alignment of CMA region
[ 0.000000@0] linux,codec_mm_reserved: 0x0000000075200000 - 0x0000000079300000 (65 MiB)
[ 0.000000@0] fdt Reserved memory total: 354 MiB
[ 0.000000@0] cma: Reserved 8 MiB at 74800000
[ 0.000000@0] psci: probing function IDs from device-tree
[ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc07516e000 s19968 r8192 d20992 u49152
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 510280
[ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=disabled logo=osd1,loaded,0x3d800000,1080p60hz maxcpus=8 vout=1080p60hz,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 androidboot.firstboot=0 jtag=apao androidboot.hardware=amlogic mac=86:37:20:48:cb:3e androidboot.mac=86:37:20:48:cb:3e aml_dt=gxm_q201_2g recovery_part={recovery_part} recovery_offset={recovery_offset} aml_dt=gxm_q201_2g recovery_part={recovery_part} recovery_offset={recovery_offset} aml_dt=gxm_q201_2g recovery_part={recovery_part} recovery_offset={recovery_offset}
[ 0.000000@0] logo: osd1
[ 0.000000@0] logo: loaded
[ 0.000000@0] logo: 0x3d800000
[ 0.000000@0] logo: 1080p60hz
[ 0.000000@0] vout_serve: 1080p60hz
[ 0.000000@0] vout_serve: enable: 1
[ 0.000000@0] logo: get hdmimode: 1080p60hz
[ 0.000000@0] logo: get cvbsmode: 576cvbs
[ 0.000000@0] tv_vout: cvbs performance line = 0
[ 0.000000@0] jtag: jtag select 2
[ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000@0] Memory: 1640852K/2077696K available (10612K kernel code, 1153K rwdata, 3884K rodata, 1263K init, 5869K bss, 436844K reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
[ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff80423cc800 ( 35 MB)
[ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc07f100000 ( 2033 MB)
[ 0.000000@0] .init : 0xffffffc001eaa000 - 0xffffffc001fe5e00 ( 1264 kB)
[ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001ea9334 ( 14501 kB)
[ 0.000000@0] .data : 0xffffffc001fe6000 - 0xffffffc002106540 ( 1154 kB)
[ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01ea8fff]
[ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000@0] arch_multi_cluster:1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[ 0.008244@0] meson_bc_timer: mclk->mux_reg =ffffff8000014990,mclk->reg =ffffff8000016994
[ 0.016829@0] Console: colour dummy device 80x25
[ 0.021097@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.031672@0] pid_max: default: 32768 minimum: 301
[ 0.036581@0] Security Framework initialized
[ 0.040787@0] SELinux: Initializing.
[ 0.044532@0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.051369@0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.061614@0] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
[ 0.065714@0] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
[ 0.072721@0] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
[ 0.079713@0] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
[ 0.090049@0] Initializing cgroup subsys debug
[ 0.091175@0] Initializing cgroup subsys freezer
[ 0.095843@0] ftrace: allocating 36489 entries in 143 pages
[ 0.149512@0] /cpus/cpu@0: Missing clock-frequency property
[ 0.149556@0] /cpus/cpu@1: Missing clock-frequency property
[ 0.155138@0] /cpus/cpu@2: Missing clock-frequency property
[ 0.160765@0] /cpus/cpu@3: Missing clock-frequency property
[ 0.166339@0] /cpus/cpu@100: Missing clock-frequency property
[ 0.172121@0] /cpus/cpu@101: Missing clock-frequency property
[ 0.177891@0] /cpus/cpu@102: Missing clock-frequency property
[ 0.183672@0] /cpus/cpu@103: Missing clock-frequency property
[ 0.189439@0] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 0.239787@0] Meson chip version = RevA (22:A - 82:0)
[ 0.258195@1] CPU1: Booted secondary processor
[ 0.278163@2] CPU2: Booted secondary processor
[ 0.298172@3] CPU3: Booted secondary processor
[ 0.318197@4] CPU4: Booted secondary processor
[ 0.338199@5] CPU5: Booted secondary processor
[ 0.358215@6] CPU6: Booted secondary processor
[ 0.378239@7] CPU7: Booted secondary processor
[ 0.378331@0] Brought up 8 CPUs
[ 0.407146@0] SMP: Total of 8 processors activated.
[ 0.421757@2] sched: registering cpufreq notifiers for scale-invariant loads
[ 0.423282@2] instabooting: 0
[ 0.435407@2] pinctrl core: initialized pinctrl subsystem
[ 0.436105@2] regulator-dummy: no parameters
[ 0.440375@2] NET: Registered protocol family 16
[ 0.446823@3] ramoops: using module parameters
[ 0.449279@2] console [pstore-1] enabled
[ 0.452587@2] pstore: Registered ramoops as persistent store backend
[ 0.458962@2] ramoops: attached 0x100000@0x7300000, ecc: 0/0
[ 0.465571@3] cpuidle: using governor menu
[ 0.469074@3] aml_vdac_init: module init
[ 0.472882@2] register canvas platform driver
[ 0.477204@2] register rdma platform driver
[ 0.483704@2] vdso: 2 pages (1 code, 1 data) at base ffffffc001ff0000
[ 0.487809@2] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.495139@2] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.502039@2] software IO TLB [mem 0x64400000-0x64800000] (4MB) mapped at [ffffffc064400000-ffffffc0647fffff]
[ 0.511026@2] Serial: AMBA PL011 UART driver
[ 0.515898@3] aml_i2c version: 20140813
[ 0.519468@3] i2c-core: driver [pmu4] using legacy resume method
[ 0.525355@3] codec_mm:codec_mm_module_init
[ 0.529688@2] aml_watch_point_probe, in
[ 0.533717@2] gxbb_mpll_clk: register mpll_clk_out0 success done
[ 0.539312@2] gxbb_mpll_clk: register mpll_clk_out1 success done
[ 0.545327@2] gxbb_mpll_clk: register mpll_clk_out2 success done
[ 0.551573@2] clk_sys: register PLL sys_pll success done
[ 0.556707@2] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
[ 0.562071@2] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
[ 0.567200@2] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
[ 0.572718@2] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
[ 0.578662@2] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
[ 0.584629@2] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
[ 0.590474@2] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
[ 0.596342@2] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
[ 0.602198@2] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
[ 0.608095@2] gxl_clk: clock initialization complete
[ 0.613265@2] clkmsr: Gxl msr_clk_reg0=ffffff800003c75c,msr_clk_reg2=ffffff800003e764
[ 0.623526@2] aml_iomap: amlogic iomap probe done
[ 0.626293@3] pinmux-gxl c1109880.pinmux: Init pinux probe!
[ 0.632244@3] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
[ 0.638456@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.645978@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ 0.654207@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.662071@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
domain-0 init dvfs: 4
domain-1 init dvfs: 4
[ 0.682212@2] codec_mm has 2 memory regions
[ 0.682282@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.688914@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.697509@2] codec_mm has 2 memory regions
[ 0.701593@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.709618@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.720175@2] vpu: driver version: v02
[ 0.721891@2] vpu: load vpu_clk: 666667000Hz(7)
[ 0.726521@2] vpu: vpu_probe OK
[ 0.731344@2] tv_vout: tvout_probe
[ 0.732988@2] tv_vout: major number 254 for disp
[ 0.737614@2] vout_notify: vout_register_server
[ 0.742176@2] tv_vout: register tv module server ok
[ 0.747176@2] tv_vout: tvout_probe OK
[ 0.751388@2] canvas_probe reg=00000000c8838000,size=400
[ 0.756110@2] canvas maped reg_base =ffffff800009a000
[ 0.765485@2] rdma_probe
[ 1.079885@2] bio: create slab <bio-0> at 0
[ 1.081068@2] SCSI subsystem initialized
[ 1.083137@3] usbcore: registered new interface driver usbfs
[ 1.088255@2] usbcore: registered new interface driver hub
[ 1.093873@2] usbcore: registered new device driver usb
[ 1.100089@2] i2c-gpio i2c_gpio.38: using pins 172 (SDA) and 173 (SCL)
[ 1.105598@3] Linux video capture interface: v2.00
[ 1.110542@3] pps_core: LinuxPPS API ver. 1 registered
[ 1.115677@3] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 1.124916@3] PTP clock support registered
[ 1.129650@2] hdmitx: system: amhdmitx_init
[ 1.133108@2] hdmitx: system: Ver: 2014May6
[ 1.137482@2] hdmitx: system: amhdmitx_probe
[ 1.141992@2] hdmitx: system: not find match init-data
[ 1.146757@2] hdmitx: system: not find match pwr-ctl
[ 1.151755@2] hdmitx hpd irq = 89
[ 1.155559@2] hdmitx20: Mapped PHY: 0xc0800000
[ 1.159541@2] hdmitx20: Mapped PHY: 0xc1104400
[ 1.164087@2] hdmitx20: Mapped PHY: 0xc8100000
[ 1.168459@2] hdmitx20: Mapped PHY: 0xc8834000
[ 1.172918@2] hdmitx20: Mapped PHY: 0xc883a000
[ 1.177388@2] hdmitx20: Mapped PHY: 0xc883c000
[ 1.181847@2] hdmitx20: Mapped PHY: 0xd0100000
[ 1.186306@2] hdmitx20: Mapped PHY: 0xda83a000
[ 1.190810@2] hdmitx: alread display in uboot 0x10
[ 1.195599@2] avmute set to 1
[ 1.198983@3] vout_serve: vout_init_module
[ 1.202814@3] tv_vout: tv_set_current_vmode[759]fps_target_mode=16
[ 1.205662@0] hdmitx: system: irq 80000002
[ 1.213028@3] tv_vout: mode is 16,sync_duration_den=1,sync_duration_num=60
[ 1.219911@3] tv_vout: already display in uboot
[ 1.224461@3] vout_serve: vinfo mode is: 1080p60hz
[ 1.229267@3] vout_serve: init mode 1080p60hz
[ 1.233766@3] vout_serve: create vout attribute OK
[ 1.238463@3] vout_serve: meson_vout_probe OK
[ 1.243043@0] logo: logo_init
[ 1.246216@0] osd_rdma: osd_rdma_init: rdma_table p=0x74841000,op=0x74841000 , v=0xffffff800009e000
[ 1.254938@0] osd_rdma: osd rdma request irq as second interrput function!
[ 1.262337@3] Advanced Linux Sound Architecture Driver Initialized.
[ 1.268828@0] Bluetooth: Core ver 2.18
[ 1.272000@0] NET: Registered protocol family 31
[ 1.276539@0] Bluetooth: HCI device and connection manager initialized
[ 1.283089@0] Bluetooth: HCI socket layer initialized
[ 1.288201@0] Bluetooth: L2CAP socket layer initialized
[ 1.293432@0] Bluetooth: SCO socket layer initialized
[ 1.299009@0] cfg80211: Calling CRDA to update world regulatory domain
[ 1.305177@3] NetLabel: Initializing
[ 1.308641@3] NetLabel: domain hash size = 128
[ 1.313179@3] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.318402@3] NetLabel: unlabeled traffic allowed by default
[ 1.326925@0] Switched to clocksource arch_sys_counter
[ 1.376353@1] [amlatvdemod..]aml_atvdemod_init.
[ 1.376503@1] NET: Registered protocol family 2
[ 1.380401@1] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.387470@1] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 1.394380@1] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.401001@2] TCP: reno registered
[ 1.404295@2] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 1.410553@2] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 1.417429@2] NET: Registered protocol family 1
[ 1.422013@2] RPC: Registered named UNIX socket transport module.
[ 1.427838@2] RPC: Registered udp transport module.
[ 1.432722@2] RPC: Registered tcp transport module.
[ 1.437637@2] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.444490@2] aml_wifi wifi.33: [wifi_dev_probe] no power_on_pin2
[ 1.450408@2] aml_wifi wifi.33: [wifi_dev_probe] set pwm as 32k output
[ 1.457018@2] aml_wifi wifi.33: [wifi_dev_probe] dhd_static_buf setup
[ 1.463500@2] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem: WIFI MEM Allocated
[ 1.471087@2] aml_wifi wifi.33: [wifi_dev_probe] interrupt_pin=241
[ 1.477270@2] aml_wifi wifi.33: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
[ 1.484699@2] aml_wifi wifi.33: [wifi_dev_probe] power_on_pin=240
[ 1.490831@2] aml_wifi wifi.33: [wifi_dev_probe] clock_32k_pin=0
[ 1.497227@0] aml_wifi wifi.33: [wifi_setup_dt] wifi_setup_dt
[ 1.502701@0] aml_wifi wifi.33: [wifi_setup_dt] interrupt_pin(241)
[ 1.508881@0] aml_wifi wifi.33: [wifi_setup_dt] power_on_pin(240)
[ 1.515360@1] Unpacking initramfs...
[ 1.537075@3] hdmitx: plugin
[ 1.653094@1] Freeing initrd memory: 3756K (ffffffc073b0b000 - ffffffc073eb6000)
[ 1.660722@1] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 1.661706@1] audit: initializing netlink subsys (disabled)
[ 1.667268@1] audit: type=2000 audit(1.570:1): initialized
[ 1.673640@2] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.673785@3] hdmitx: edid: check sum valid
[ 1.673787@3] hdmitx: edid: check sum valid
[ 1.673790@3] hdmitx: edid: blk0 raw data
[ 1.673830@3] 00ffffffffffff001e6de37689bb02000b18010380502278eaca95a6554ea126
[ 1.673830@3] 0f50542108007140818081c0a9c0b300d1c0810001019d6770a0d0a022503020
[ 1.673830@3] 3a00204f3100001a000000fd00383d1e5a1e000a202020202020000000fc004c
[ 1.673830@3] 4720554c545241574944450a000000000000000000000000000000000000017c
[ 1.673830@3]
[ 1.673830@3]
[ 1.673832@3] hdmitx: edid: blk1 raw data
[ 1.673871@3] 020317f14410040301230907078301000065030c0010009f3d70a0d0a0155030
[ 1.673871@3] 203a00204f3100001a7e4800e0a0381f4040403a00204f31000018011d007251
[ 1.673871@3] d01e206e285500204f3100001e8c0ad08a20e02d10103e9600204f3100001800
[ 1.673871@3] 0000ff003431314b4b484e35393038310a0000000000000000000000000000ce
[ 1.673871@3]
[ 1.673871@3]
[ 1.673875@3] EDID Parser:
[ 1.673920@3] hdmitx: edid: find IEEEOUT
[ 1.673943@3]
[ 1.673945@3] hdmitx: edid: check sum valid
[ 1.673946@3] hdmitx: edid: check sum valid
[ 1.673950@3] hdmitx: update RX hdr info 0
[ 1.675973@3] hdmitx: ddc rd8b error 0x3a 0x00 0x00
[ 1.678017@3] [RX]-receive ksv list len:1,depth:1,cas:0,dev:0
[ 1.678023@3] hdmitx: video: get current mode: 1080p60hz
[ 1.678025@3] hdmitx: update rx hdr info 0
[ 1.678041@3] hdmitx: get ext_name (null)
[ 1.678046@3] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 16
[ 1.678051@3] hdmtix: set audio
[ 1.678061@3] hdmitx tx_aud_src = 0
[ 1.678090@3] hdmitx: fs = 0, cd = 4, tmds_clk = 148500
[ 1.678092@3] hdmitx aud_n_para = 6144
[ 1.678111@3] hdmitx set channel status
[ 1.839430@2] VFS: Disk quotas dquot_6.5.2
[ 1.839714@2] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.850110@2] NFS: Registering the id_resolver key type
[ 1.850190@2] Key type id_resolver registered
[ 1.854236@2] Key type id_legacy registered
[ 1.858621@2] NTFS driver 2.1.30 [Flags: R/O].
[ 1.863354@2] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.871059@2] fuse init (API version 7.22)
[ 1.874958@1] msgmni has been set to 3612
[ 1.880261@2] NET: Registered protocol family 38
[ 1.883328@1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 1.890580@1] io scheduler noop registered
[ 1.894661@1] io scheduler deadline registered
[ 1.899426@2] io scheduler cfq registered (default)
[ 1.955181@2] meson-rng c8834000.rng: hwrng registered
[ 1.959375@3] loop: module loaded
[ 1.960018@3] zram: Created 1 device(s) ...
[ 1.963325@3] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.971273@3] tun: Universal TUN/TAP device driver, 1.6
[ 1.974194@3] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 2.105630@2] libphy: stmmac: probed
[ 2.105667@2] eth0: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[ 2.110221@2] eth0: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07)
[ 2.116652@2] PPP generic driver version 2.4.2
[ 2.120865@3] PPP BSD Compression module registered
[ 2.125514@3] PPP Deflate Compression module registered
[ 2.130800@3] PPP MPPE Compression module registered
[ 2.135751@3] NET: Registered protocol family 24
[ 2.140615@2] usbcore: registered new interface driver asix
[ 2.146158@2] usbcore: registered new interface driver ax88179_178a
[ 2.152439@3] usbcore: registered new interface driver cdc_ether
[ 2.158473@3] usbcore: registered new interface driver net1080
[ 2.164318@2] usbcore: registered new interface driver cdc_subset
[ 2.170508@3] usbcore: registered new interface driver zaurus
[ 2.176231@3] usbcore: registered new interface driver cdc_ncm
[ 2.182342@2] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.188728@2] ehci-h20ahb: H20AHB-EHCI Host Controller driver
[ 2.194771@3] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.201338@2] usbcore: registered new interface driver cdc_acm
[ 2.206715@2] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.215117@3] usbcore: registered new interface driver usb-storage
[ 2.221486@2] usbcore: registered new interface driver usbserial
[ 2.228010@2] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff80000da000
[ 2.238164@2] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
[ 2.244713@2] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff80000ee080
[ 2.256127@2] mousedev: PS/2 mouse device common for all mice
[ 2.261730@2] usbcore: registered new interface driver xpad
[ 2.266990@2] i2c /dev entries driver
[ 2.270805@3] usbcore: registered new interface driver uvcvideo
[ 2.276364@3] USB Video Class driver (1.1.1)
[ 2.281627@2] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: [email protected]
[ 2.289441@2] Bluetooth: HCI UART driver ver 2.2
[ 2.293952@2] Bluetooth: HCI H4 protocol initialized
[ 2.299351@2] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
[ 2.306699@0] cpu cpu4: bL_cpufreq_init: CPU 4 initialized
[ 2.310217@0] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
[ 2.317993@0] CPUidle arm64: cpuidle init start!!
[ 2.323198@2] @@@@@@@@@@_____2______in dia_init()
[ 2.327149@2] ATVR driver - init called!
[ 2.331174@2] usbcore: registered new interface driver usbhid
[ 2.336824@2] usbhid: USB HID core driver
[ 2.341255@3] ashmem: initialized
[ 2.344339@2] logger: created 256K log 'log_main'
[ 2.349060@2] logger: created 256K log 'log_events'
[ 2.353946@3] logger: created 256K log 'log_radio'
[ 2.358808@2] logger: created 256K log 'log_system'
[ 2.364707@2] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff80000fc4c0
[ 2.370771@2] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
[ 2.385739@2] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
[ 2.388392@2] console [ttyS0] enabled
[ 2.388392@2] console [ttyS0] enabled
[ 2.395608@2] bootconsole [earlycon0] disabled
[ 2.395608@2] bootconsole [earlycon0] disabled
[ 2.404791@3] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff80000fe4c0
[ 2.411428@3] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
[ 2.421254@2] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff]
[ 2.430674@2] meson-gpu-clkgen: probe of c883c000.gpu_clk failed with error -16
[ 2.438147@3] hdmitx: system: hdmitx_hdcp_init
[ 2.442445@3] ESM HLD: Initializing...
[ 2.445979@3] ESM HLD: Registering device range 'esm'...
[ 2.451258@3] ESM HLD: Device range 'esm' has been registered.
[ 2.457032@3] ESM HLD: Creating class /sys/class/elliptic...
[ 2.462721@2] ESM HLD: The class /sys/class/elliptic has been created.
[ 2.469107@2] ESM HLD: Creating device 'esm'...
[ 2.473707@2] ESM HLD: Device 'esm' has been created.
[ 2.478613@2] ESM HLD: Done initializing the HLD driver.
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[ 2.499836@3] aml_vrtc rtc.32: rtc core: registered aml_vrtc as rtc0
[ 2.501218@2] secmon has 1 memory regions
[ 2.504544@2] secmon: share in base: 0xffffff800011a000, share out base: 0xffffff800011c000
[ 2.512816@2] secmon secmon.4: assigned reserved memory node linux,secmon ok
[ 2.519780@2] secmon: probe done
[ 2.523300@3] storage: storage in base: 0xffffff8001800000
[ 2.528411@3] storage: storage out base: 0xffffff8001880000
[ 2.533917@3] storage: storage block base: 0xffffff8001900000
[ 2.539617@3] storage: probe done!
[ 2.543506@2] aml_sd_emmc_probe: line 3558
[ 2.547045@2] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
[ 2.556910@2] aml_sd_emmc_reg_init 1146
[ 2.560320@2] get property: ocr_avail, value:0x00200080
[ 2.566694@2] get property: f_min, value:300000
[ 2.572825@2] get property: f_max, value:100000000
[ 2.579213@2] get property: max_req_size, value:0x00020000
[ 2.585673@2] get property: pinname, str:emmc
[ 2.591454@2] get property: card_type, value:1
[ 2.597163@2] get property: gpio_dat3, str:
[ 2.602574@2] get property: hw_reset, str:
[ 2.608043@2] emmc:pdata->caps = c0000d47
[ 2.611979@2] emmc:pdata->caps2 = 18060
[ 2.615782@2] storage 1, boot 1
[ 2.618881@2] get_storage_dev return 1
[ 2.656930@3] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.657148@3] aml_sd_emmc_probe: line 3558
[ 2.661566@3] aml_sd_emmc_reg_init 1146
[ 2.665019@3] get property: ocr_avail, value:0x00200080
[ 2.671447@3] get property: f_min, value:400000
[ 2.677571@3] get property: f_max, value:100000000
[ 2.683942@3] get property: max_req_size, value:0x00020000
[ 2.690417@3] get property: irq_in, value:3
[ 2.696103@3] get property: irq_out, value:5
[ 2.701810@3] get property: gpio_cd, str:
[ 2.707235@3] get property: pinname, str:sd
[ 2.712837@3] get property: jtag_pin, str:
[ 2.718276@3] get property: card_type, value:5
[ 2.723964@3] get property: gpio_dat3, str:
[ 2.729413@3] sd:pdata->caps = 7
[ 2.732586@3] sd:pdata->caps2 = 0
[ 2.767132@3] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.767180@4] [aml_is_card_insert] card IN
[ 2.771400@3] aml_sd_emmc_probe: line 3558
[ 2.775789@3] aml_sd_emmc_reg_init 1146
[ 2.779288@3] get property: ocr_avail, value:0x00200080
[ 2.785691@3] get property: f_min, value:400000
[ 2.791822@3] get property: f_max, value:200000000
[ 2.798203@3] get property: max_req_size, value:0x00020000
[ 2.804669@3] get property: pinname, str:sdio
[ 2.810451@3] get property: card_type, value:3
[ 2.816175@3] sdio:pdata->caps = 7810f
[ 2.819850@3] sdio:pdata->caps2 = 0
[ 2.856932@1] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.857463@1] ion_dev has 1 memory regions
[ 2.863669@1] emm�-=AM}9�bit is not set
[ 2.868528@4] normal card in
[ 2.874426@1] emmc: trying cali 0-th time(s)
[ 2.877692@1] emmc: delay[0]= 4600 padding= 2, bidx=4
[ 2.878056@1] emmc: delay[1]= 4400 padding= 3, bidx=4
[ 2.883058@1] emmc: delay[2]= 4400 padding= 3, bidx=4
[ 2.888073@1] emmc: delay[3]= 4800 padding= 1, bidx=4
[ 2.890555@2] fb: osd_init_module
[ 2.890680@2] fb: viu vsync irq: 35
[ 2.890685@2] fb: failed to init reserved memory
[ 2.890696@2] fb: osd_probe vinfo:ffffffc002086d98
[ 2.890700@2] fb: init fbdev bpp is:32
[ 2.912833@1] emmc: delay[4]= 4800 padding= 1, bidx=4
[ 2.917831@1] emmc: delay[5]= 4600 padding= 2, bidx=4
[ 2.922820@1] emmc: delay[6]= 4600 padding= 2, bidx=4
[ 2.927835@1] emmc: delay[7]= 4800 padding= 1, bidx=4
[ 2.932825@1] emmc: calibration result @ 0: max(4800), min(4400)
[ 2.933424@0] fb: osd probe OK
[ 2.933657@0] ge2d: ge2d_init_module
[ 2.933667@0] ge2d: ge2d_dev major:243
[ 2.934008@0] ge2d: ge2d clock is 400 MHZ
[ 2.934012@0] ge2d: ge2d: pdev=fffeffc06528a000, irq=182, rstc=0xffffffc0630fbd80, clk=ffffffc065278800
[ 2.934065@0] ge2d: mapped phy: 0xd0160000
[ 2.934070@0] ge2d: ge2d start monitor
[ 2.934122@3] ge2d: ge2d workqueue monitor start
[ 2.934322@2] sysled: module init
[ 2.934434@2] sysled: led_gpio = 154
[ 2.934435@2] sysled: active_low = 0
[ 2.934591@0] sysled: module probed ok
[ 2.934981@0] pwmled: module init
[ 2.935070@0] codec:Amlogic A/V streaming port init
[ 2.936437@2] codec:get gate demux control ok ffffffc06424aa00
[ 2.936442@2] codec:get gate parser_top control ok ffffffc06424aa80
[ 2.936446@2] codec:get gate vpu_intr control ok ffffffc06424ab00
[ 2.936452@2] codec:get gate vdec control ok ffffffc06424ab80
[ 2.937122@2] codec:[tsync_pcr_init]init success.
[ 2.937124@2] codec:amvideocap_init_module
[ 2.937257@2] codec:amvideocap_probe,amvideocap
[ 2.937260@2] codec:use cma buf.
[ 2.937261@2] codec:amvideocap_dev_register
[ 2.939090@0] amvenc_avc_probe -- reserved memory config fail.
[ 2.939092@0] amvenc_avc - cma memory pool size: 40 MB
[ 2.939111@0] encode_wq_init.
[ 2.939116@0] encode start monitor.
[ 2.939170@3] encode workqueue monitor start.
[ 2.939580@0] jpegenc module init
[ 2.939880@2] codec:picdec_driver_probe called.
[ 2.939883@2] picdec has 1 memory regions
[ 2.939904@2] codec:picdec_driver_probe done.
[ 2.940819@2] codec:create_ge2d_work_queue video task ok
[ 2.941197@0] codec:used fix clk for vdec clk source!
[ 2.941202@0] codec:register clk_set_setting cpu[34]
[ 2.941538@0] vpu_init
[ 2.941710@0] vpu_probe
[ 2.941714@0] HevcEnc reserved memory config fail.
[ 2.941717@0] HevcEnc - cma memory pool size: 64 MB
[ 2.941719@0] HevcEnc - wave420l_irq: 219
[ 2.941759@0] vpu base address get from platform driver physical base addr=0xc8810000, virtual base=0xffffff8000258000
[ 2.942053@0] success to probe vpu device with video memory from cma
[ 2.942203@2] DI: di_module_init ok.
[ 2.942206@2] DI: di_module_init: major 236
[ 2.942415@0] DI: di_probe
[ 2.942531@2] deinterlace has 1 memory regions
[ 2.942563@2] deinterlace deinterlace.26: assigned reserved memory node linux,di ok
[ 2.942583@2] di_irq:78,timerc_irq:38
[ 2.942719@2] rdma_register, rdma_table_addr ffffff800016c000 rdma_table_addr_phy 74848000 reg_buf ffffffc0633a4000
[ 2.942722@2] rdma_register success, handle 1 table_size 8192
[ 2.942723@2] DI: di_probe allocate rdma channel 1.
[ 2.942727@2] DI: DI hw version 2.
[ 2.942737@2] 0x000000db:Y=db,U=0,V=0
[ 2.942739@2] 0x000000dc:Y=dc,U=0,V=0
[ 2.942740@2] 0x000000dd:Y=dd,U=0,V=0
[ 2.942742@2] 0x000000de:Y=de,U=0,V=0
[ 2.942744@2] 0x000000df:Y=df,U=0,V=0
[ 2.942745@2] 0x000000e0:Y=e0,U=0,V=0
[ 2.942747@2] 0x000000e1:Y=e1,U=0,V=0
[ 2.942748@2] 0x000000e2:Y=e2,U=0,V=0
[ 2.942750@2] 0x000000e3:Y=e3,U=0,V=0
[ 2.942752@2] 0x000000f0:Y=f0,U=0,V=0
[ 2.942755@2] 0x000000f1:Y=f1,U=0,V=0
[ 2.942757@2] 0x000000f2:Y=f2,U=0,V=0
[ 2.942758@2] 0x000000f3:Y=f3,U=0,V=0
[ 2.942760@2] 0x000000f4:Y=f4,U=0,V=0
[ 2.942762@2] 0x000000f5:Y=f5,U=0,V=0
[ 2.942763@2] 0x000000f6:Y=f6,U=0,V=0
[ 2.942767@2] 0x000000f7:Y=f7,U=0,V=0
[ 2.942769@2] 0x000000f8:Y=f8,U=0,V=0
[ 2.942771@2] 0x000000f9:Y=f9,U=0,V=0
[ 2.942772@2] 0x000000fa:Y=fa,U=0,V=0
[ 2.942774@2] 0x000000fb:Y=fb,U=0,V=0
[ 2.942775@2] 0x000000fc:Y=fc,U=0,V=0
[ 2.942910@2] DI: di_probe here.
[ 2.943244@0] efusekeynum: 4
[ 2.943252@0] efusekeyname: mac offset: 0 size: 6
[ 2.943257@0] efusekeyname: mac_bt offset: 6 size: 6
[ 2.943263@0] efusekeyname: mac_wifi offset: 12 size: 6
[ 2.943267@0] efusekeyname: usid offset: 18 size: 16
[ 2.943477@0] efuse efuse.10: probe OK!
[ 2.943811@2] key unify config unifykey-num is 14
[ 2.943864@2] key unify fact unifykey-num is 14
[ 2.943868@2] aml_unifykeys_probe:1273=============unifykey_devno:ea00000
[ 2.944084@2] 6unifykey: device unifykeys created ok
[ 2.944200@0] 6aml_unifykeys_init done!
[ 2.944202@0] PPMGRDRV: warn: ppmgr module init func called
[ 2.944317@0] PPMGRDRV: err: ppmgr_driver_probe called
[ 2.944320@0] ppmgr has 1 memory regions
[ 2.944346@0] PPMGRDRV: info: ppmgr_dev major:233
[ 2.944556@0] PPMGRDRV: info: ppmgr_probe done
[ 2.944923@0] amlogic rfkill init
[ 2.945015@0] enter bt_probe of_node
[ 2.945029@0] not get gpio_en
[ 2.945300@0] power on valid level is high
[ 2.945301@0] Bluetooth: BlueSleep Mode Driver Ver 1.2
[ 2.945708@2] ionvideo-000: V4L2 device registered as video13
[ 2.945709@2] ionvid: info: Video Technology Magazine Ion Video
[ 2.945711@2] ionvid: info: Capture Board ver 1.0 successfully loaded
[ 2.945719@2] audio_dsp: [dsp]register dsp to char divece(257)
[ 2.946327@0] amaudio: amaudio: driver amaudio succuess!
[ 2.946614@2] amlvid:err: amlvideo_init called
[ 2.946614@2] amlvid:err: amlvideo_create_instance called
[ 2.946617@2] amlvid:err: v4l2_dev.name=:amlvideo-000
[ 2.946731@0] amlvideo-000: V4L2 device registered as video10
[ 2.947123@0] vdin_drv_init: major 232
[ 2.947441@0] vdin_drv_init: vdin driver init done
[ 2.947446@0] tvafe_drv_init: major 231
[ 2.947721@0] tvafe: tvafe_init.
[ 2.947980@0] [RX]-hdmirx: hdmirx_init.
[ 2.947983@0] ESM HLD: Initializing...
[ 2.947985@0] ESM HLD: Registering device range 'esm_rx'...
[ 2.947992@0] ESM HLD: Device range 'esm_rx' has been registered.
[ 2.947993@0] ESM HLD: Creating class /sys/class/elliptic_rx...
[ 2.948060@2] ESM HLD: The class /sys/class/elliptic_rx has been created.
[ 2.948062@2] ESM HLD: Creating device 'esm_rx'...
[ 2.948176@0] ESM HLD: Device 'esm_rx' has been created.
[ 2.948178@0] ESM HLD: Done initializing the HLD driver.
[ 2.948180@0] [viuin..]viuin_init_module viuin module init
[ 2.948555@0] [viuin..]viuin_probe probe ok.
[ 2.948626@2] module init
[ 2.948742@2]
[ 2.948742@2] VECM probe start
[ 2.948992@2] aml_vecm_probe: ok
[ 2.949572@0] saradc c1108680.saradc: initialized by BL30
[ 2.949582@0] saradc c1108680.saradc: calibration start:
[ 2.949627@0] saradc c1108680.saradc: nominal=0, value=3
[ 2.949673@0] saradc c1108680.saradc: nominal=256, value=251
[ 2.949717@0] saradc c1108680.saradc: nominal=512, value=499
[ 2.949760@0] saradc c1108680.saradc: nominal=768, value=748
[ 2.949804@0] saradc c1108680.saradc: nominal=1023, value=996
[ 2.949807@0] saradc c1108680.saradc: calibration end: coef=4219
[ 2.949974@2] remote: Driver init
[ 2.950049@2] remote: platform_data g_remote_ao_offset=580
[ 2.950051@2] remote: platform_data irq =228
[ 2.950075@2] remote: set drvdata completed
[ 2.950085@2] remote: device_create_file completed
[ 2.950377@2] input: aml_keypad as /devices/meson-remote.12/input/input0
[ 2.950634@2] remote: input_register_device completed
[ 2.950677@2] remote: set_remote_mode[74]
[ 2.950700@2] remote: remote config major:228
[ 2.950884@2] remote: physical address:0x633fa000
[ 2.951471@2] gpio-key gpio_keypad.48: gpio_key: 0 name(power) pin()
[ 2.951476@2] gpio-key gpio_keypad.48: amlogic_gpio_name_map_num pin 0!::
[ 2.951491@2] gpio-key gpio_keypad.48: gpio_key: 0 power(147)
[ 2.951517@2] gpio-key gpio_keypad.48: start setup_timer
[ 2.951524@2] gpio-key gpio_keypad.48: power key(116) registed.
[ 2.951720@0] input: gpio_keypad as /devices/gpio_keypad.48/input/input1
[ 2.951844@2] gpio-key gpio_keypad.48: gpio keypad register input device completed.
[ 2.951852@2] input input1: gpio keypad major:227
[ 2.952996@0] Sensor: lsm303d_init
[ 2.953212@2] Sensor: stk8313_init
[ 2.953290@0] Sensor: stk831x_init
[ 2.953361@2] Sensor: mxc622x_acc_init
[ 2.953432@0] Sensor: mxc6255xc_acc_init
[ 2.953571@0] Sensor: l3gd20_gyr_init
[ 2.954499@0] aml dvb init
[ 2.954904@0] Amlogic Demod DVB-T/C DebugIF Init
[ 2.955087@0] Amlogic Demod DVB-T/C DebugIF Init ok----------------
[ 2.955890@0] jtag: module init
[ 2.956066@2] jtag: pinctrl setup apao
[ 2.956068@2] jtag: set state 2
[ 3.096951@2] input input1: key 116 up
[ 3.681858@1] emmc: line_delay =0x1100221, max_cal_result =4800
[ 3.687693@1] emmc: base_index_max 4, base_index_min 4
[ 3.692778@1] emmc: clk 100000000 SDR mode tuning start
fuse_pw_en: 0x3
WARNING! efuse bits is disabled
Enable A53 JTAG cluster 0 to AO
[ 3.711006@0] jtag: module probed ok
[ 3.711461@0] cpuinfo: probe done
[ 3.711481@1] emmc: rx_tuning_result[0] = 10
[ 3.716838@1] defendkey c8834500.defendkey: defendkey_devno:df00000
[ 3.722936@1] emmc: rx_tuning_result[1] = 10
[ 3.722993@3] defendkey c8834500.defendkey: defendkey: device defendkey created ok
[ 3.723202@2] defendkey: driver init
[ 3.723877@3] input: cec_input as /devices/virtual/input/input2
[ 3.724107@2] cectx aocec: no hdmirx reg resource
[ 3.724110@2] cectx aocec: no hhi reg resource
[ 3.724200@2] cectx aocec: can't find hdmirx
[ 3.725205@2] cec: wake up flag:0
[ 3.726186@3] aml_aes_dma c883e000.aml_aes: Aml AES_dma
[ 3.726743@2] aml_tdes_dma c883e000.aml_tdes: Aml TDES_dma
[ 3.727869@3] aml_sha_dma c883e000.aml_sha: Aml SHA1/SHA224/SHA256 dma
[ 3.728406@2] usbcore: registered new interface driver snd-usb-audio
[ 3.729744@2] aml_codec_T9015 c8832000.t9015: aml_T9015_audio_codec_probe
[ 3.731751@3] aml_pcm_dai: pcm mode detection =1
[ 3.732116@2] aml_spdif_dai: enterd aml_spdif_play,set_clock:-1,sample_rate=4
[ 3.732134@2] aml_spdif_dai: set normal 512 fs /4 fs
[ 3.732142@2] aml_audio_hw: IEC958 16bit
[ 3.732145@2] hdmitx: audio: aout notify rate 48000
[ 3.732147@2] hdmitx: audio: aout notify size 16
[ 3.732149@2] hdmitx: audio: aout notify format CT_PCM
[ 3.732152@2] hdmtix: set audio
[ 3.732165@2] hdmitx tx_aud_src = 0
[ 3.732191@2] hdmitx: fs = 3, cd = 4, tmds_clk = 148500
[ 3.732193@2] hdmitx aud_n_para = 6144
[ 3.732211@2] hdmitx set channel status
[ 3.732271@2] hdmitx: audio: Audio Type: PCM
[ 3.732273@2] hdmitx: audio: set audio param
[ 3.855295@1] emmc: rx_tuning_result[2] = 10
[ 3.857836@1] emmc: rx_tuning_result[3] = 10
[ 3.862051@1] emmc: rx_tuning_result[4] = 10
[ 3.866279@1] emmc: rx_tuning_result[5] = 10
[ 3.870519@1] emmc: rx_tuning_result[6] = 10
[ 3.874732@1] emmc: rx_tuning_result[7] = 10
[ 3.878963@1] emmc: rx_tuning_result[8] = 10
[ 3.882704@1] emmc: best_win_start =0, best_win_size =9
[ 3.887836@1] emmc: sd_emmc_regs->gclock=0x100024a,sd_emmc_regs->gadjust=0x42000
[ 3.895160@1] emmc: gclock =0x100024a, gdelay=0x1100221, gadjust=0x42000
[ 3.902141@1] emmc: new HS200 MMC card at address 0001
[ 3.906889@1] emmc: clock 100000000, 8-bit-bus-width
[ 3.912375@2] mmcblk0: emmc:0001 NCard 14.4 GiB
[ 3.916849@2] mmcblk0boot0: emmc:0001 NCard partition 1 4.00 MiB
[ 3.923192@2] mmcblk0boot1: emmc:0001 NCard partition 2 4.00 MiB
[ 3.928980@2] mmcblk0rpmb: emmc:0001 NCard partition 3 4.00 MiB
[ 3.935617@1] mmcblk0: unknown partition table
[ 3.937171@2] aml_snd_card: headphone detection disable=1
[ 3.937174@2] aml_snd_card: no spk event delay time set
[ 7.950254@2] aml_snd_m8_card aml_m8_snd.47: T9015-audio-hifi <-> I2S.40 mapping ok
[ 3.950546@1] [mmc_read_partition_tbl] mmc read partition OK!
[ 3.950547@1] add_emmc_partition
[ 3.950763@3] [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
[ 3.950902@1] [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
[ 3.951025@3] [mmcblk0p03] cache offset 0x000006c00000, size 0x000020000000
[ 3.951163@1] [mmcblk0p04] env offset 0x000027400000, size 0x000000800000
[ 3.951293@3] [mmcblk0p05] logo offset 0x000028400000, size 0x000002000000
[ 3.951422@1] [mmcblk0p06] recovery offset 0x00002ac00000, size 0x000002000000
[ 3.951543@3] [mmcblk0p07] rsv offset 0x00002d400000, size 0x000000800000
[ 3.951661@1] [mmcblk0p08] tee offset 0x00002e400000, size 0x000000800000
[ 3.951786@3] [mmcblk0p09] crypt offset 0x00002f400000, size 0x000002000000
[ 3.951911@1] [mmcblk0p10] misc offset 0x000031c00000, size 0x000002000000
[ 3.952029@3] [mmcblk0p11] instaboot offset 0x000034400000, size 0x000020000000
[ 3.952158@1] [mmcblk0p12] boot offset 0x000054c00000, size 0x000002000000
[ 3.952283@3] [mmcblk0p13] system offset 0x000057400000, size 0x000080000000
[ 3.952416@1] [mmcblk0p14] data offset 0x0000d7c00000, size 0x0002c5400000
[ 3.952446@1] card key: card_blk_probe.
[ 3.952450@1] emmc_key_init:527 emmc key lba_start:0x12020,lba_end:0x12220
[ 3.952452@1] emmc key: emmc_key_init:552 ok.
[ 3.952627@1] amlmmc_dtb_init: register dtb chardev
[ 3.952704@3] amlmmc_dtb_init: register dtb chardev OK
[ 3.952704@3] Exit aml_emmc_partition_ops OK.
[ 3.953704@1] mmcblk0boot1: unknown partition table
[ 3.954493@1] mmcblk0boot0: unknown partition table
[ 3.954736@3] clear_emmc_wait_flag
[ 4.072475@0] sd: new high speed SDHC card at address aaaa
[ 4.072926@3] sd: clock 50000000, 4-bit-bus-width
[ 4.072926@3]
[ 4.072926@3] mmcblk1: sd:aaaa SL08G 7.40 GiB
[ 4.073984@0] mmcblk1: p1
[ 4.145626@2] aml_snd_m8_card aml_m8_snd.47: dit-hifi <-> SPDIF.41 mapping ok
[ 4.151824@2] aml_pcm: enter aml_pcm_new dai->name: PCM.42 dai->id: 0
[ 4.158232@2] aml_snd_m8_card aml_m8_snd.47: pcm2bt-pcm <-> PCM.42 mapping ok
[ 4.165142@2] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTL
[ 4.172749@2] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
[ 4.181529@2] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTR
[ 4.189118@2] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
[ 4.199666@3] GACT probability NOT on
[ 4.201529@3] Mirror/redirect action on
[ 4.205315@3] u32 classifier
[ 4.208183@3] Actions configured
[ 4.211699@3] Netfilter messages via NETLINK v0.30.
[ 4.216581@3] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 4.223248@3] ctnetlink v0.93: registering with nfnetlink.
[ 4.228730@2] xt_time: kernel timezone is -0000
[ 4.232737@2] ipip: IPv4 over IPv4 tunneling driver
[ 4.238294@2] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 4.243041@2] arp_tables: (C) 2002 David S. Miller
[ 4.247819@2] TCP: cubic registered
[ 4.251112@2] Initializing XFRM netlink socket
[ 4.256407@2] NET: Registered protocol family 10
[ 4.261254@3] mip6: Mobile IPv6
[ 4.263208@3] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 4.268991@3] sit: IPv6 over IPv4 tunneling driver
[ 4.274819@2] NET: Registered protocol family 17
[ 4.278110@2] NET: Registered protocol family 15
[ 4.282753@2] Bridge firewalling registered
[ 4.286825@2] Bluetooth: RFCOMM TTY layer initialized
[ 4.291821@2] Bluetooth: RFCOMM socket layer initialized
[ 4.297044@2] Bluetooth: RFCOMM ver 1.11
[ 4.300884@2] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.306312@2] Bluetooth: BNEP filters: protocol multicast
[ 4.311730@2] Bluetooth: BNEP socket layer initialized
[ 4.316749@2] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 4.322825@2] Bluetooth: HIDP socket layer initialized
[ 4.327951@2] l2tp_core: L2TP core driver, V2.0
[ 4.332367@2] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 4.337303@2] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 4.342996@2] l2tp_netlink: L2TP netlink interface
[ 4.347771@2] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 4.353783@2] l2tp_debugfs: L2TP debugfs support
[ 4.358340@2] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 4.364930@2] NET: Registered protocol family 35
[ 4.369575@2] Key type dns_resolver registered
[ 4.375956@2] Registering SWP/SWPB emulation handler
[ 4.379561@2] regulator-dummy: disabling
[ 4.383069@2] aml_vrtc rtc.32: setting system clock to 2015-01-01 00:00:12 UTC (1420070412)
[ 4.393179@2] gxbb_pm: enter meson_pm_probe!
[ 4.395184@2] gxbb_pm: meson_pm_probe done
[ 4.400217@2] cpucore_cooling_register, max_cpu_core_num:4
[ 4.404834@2] cpucore_cooling_register, max_cpu_core_num:4
[ 4.425371@0] aml_istbt_dev_ready NULL
[ 4.42542[ 4.430139@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 4.433631@0] Freeing unused kernel memory: 1260K (ffffffc001eaa000 - ffffffc001fe5000)
[ 4.457165@2] init: init started!
[ 4.458688@2] init: init second stage started!
[ 4.459705@2] init: waitpid failed: No child processes
[ 4.465442@2] init: (Loading properties from /default.prop took 0.00s.)
[ 4.471381@2] init: /init.rc: 7: invalid command 'setcon'
[ 4.476312@2] init: /init.rc: 61: invalid command 'load_all_props'
[ 4.482589@2] init: (Parsing /init.recovery.amlogic.rc took 0.00s.)
[ 4.488617@2] init: (Parsing /init.rc took 0.02s.)
[ 4.493391@2] init: Starting service 'ueventd'...
[ 4.502045@0] ueventd: ueventd started!
[ 4.764083@3] ueventd: Coldboot took 0.26s.
[ 5.206093@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.206144@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 5.214680@3] xhci-hcd xhci-hcd.0.auto: irq 62, io mem 0xc9000000
[ 5.220663@0] hub 1-0:1.0: USB hub found
[ 5.223835@1] hub 1-0:1.0: 3 ports detected
[ 5.228187@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.233553@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 5.241931@1] hub 2-0:1.0: USB hub found
[ 5.245216@2] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 5.253112@2] init: Waiting for /dev/.coldboot_done...
[ 5.25 5.263876@2] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 5.277956@3] file system registered
[ 5.278249@3] init: write_file: Unable to write to '/sys/class/android_usb/android0/enable': No such device
[ 5.285675@3] init: write_file: Unable to open '/sys/class/android_usb/android0/f_ffs/aliases': No such file or directory
[ 5.296493@3] android_usb: Cannot enable 'adb' (-22)init: Starting service 'healthd'...
[ 5.304641@3] init: Starting service 'recovery'...
[ 5.308474@0] healthd: No charger supplies found
[ 5.308484@0] healthd: No battery devices found
[ 5.318456@3] in[ 5.325392@3] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 5.335383@3] systemcontrol: /etc/mesondisplay.cfg:12: Expected keyword, got '/etc/mesondisplay.cfg:12'.
[ 5.339473@3] vout_serve: vmode set to 1080p60hz
[ 5.343771@3] vout_serve: don't set the same mode as current
[ 5.351611@3] remote: cur_mode = 0
[ 5.352742@3] remote: set_remote_mode[74]
[ 5.357211@2] fb: osd[0] enable: 0 (recovery)
[ 5.359937@0] remote: cur_mode = 0
[ 5.359943@0] remote: set_remote_mode[74]
[ 5.378648@0] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: discard
# [ 5.416802@0] fb: osd[0] enable: 1 (recovery)
[ 5.433663@0] vout_serve: osd0=> x:0,y:0,w:1920,h:1080
[ 5.433663@0] osd1=> x:0,y:0,w:18,h:18
[ 5.441012@0] fb: current vmode=1080p60hz
[ 5.445057@0] fb: osd[1] set scale, h_scale: ENABLE, v_scale: ENABLE
[ 5.451287@0] fb: osd[1].scaledata: 1920 1920 1080 1080
[ 5.456413@0] fb: osd[1].pandata: 0 0 0 0
[ 5.466861@3] fb: osd[0] enable: 0 (recovery)
[ 5.483646@6] fb: osd[0] enable: 1 (recovery)
[ 5.546985@7] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 5.721790@4] hub 1-1:1.0: USB hub found
[ 5.721882@4] hub 1-1:1.0: 3 ports detected
[ 5.996995@7] usb 1-1.2: new low-speed USB device number 3 using xhci-hcd
[ 6.103932@6] usb 1-1.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.107361@6] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.216996@6] usb 1-1.3: new low-speed USB device number 4 using xhci-hcd
[ 6.321930@7] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.333142@7] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0003/input/input3
[ 6.341271@4] hid-generic 0003:046D:C05A.0003: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 6.380824@6] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 6.381363@6] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 6.388270@6] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 6.393697@6] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 6.400696@6] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 6.405858@6] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 6.412532@2] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 6.417879@2] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 6.524913@7] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 6.525452@7] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 6.532287@7] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 6.537803@7] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 6.544728@7] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 6.549976@7] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 6.556617@3] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 6.561951@3] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 6.668942@5] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 6.669481@5] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 6.676280@5] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 6.681842@5] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 6.688784@5] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 6.693975@5] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 6.700641@0] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 6.705963@0] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 6.812962@4] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 6.813502@4] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 6.820350@5] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 6.825836@5] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 6.832801@5] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 6.838013@5] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 6.844630@1] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 6.850003@1] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 6.956984@6] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 6.957521@6] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 6.964270@6] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 6.969904@6] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 6.976776@6] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 6.982043@6] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 6.988662@0] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 6.994003@0] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 7.101044@7] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 7.101582@7] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 7.108392@7] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 7.113918@7] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 7.120852@7] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 7.126080@7] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 7.132732@2] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 7.138101@2] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 7.245067@5] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 7.245604@5] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 7.252380@5] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 7.257955@5] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 7.264854@5] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 7.270126@5] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 7.276729@3] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 7.282130@3] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 7.389062@4] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 7.389599@4] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 7.396343@5] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 7.401951@5] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 7.408867@5] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 7.414094@5] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 7.420759@1] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 7.426082@1] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 7.533122@6] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 7.533663@6] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 7.540436@6] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 7.545996@6] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 7.552930@6] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 7.558183@6] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 7.564787@0] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 7.570187@0] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 7.677143@7] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 7.677683@7] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 7.684440@7] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 7.690051@7] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 7.696953@7] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 7.702178@7] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 7.708840@2] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 7.714166@2] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 7.821189@5] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 7.821729@5] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 7.828497@5] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 7.834063@5] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 7.840991@5] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 7.846224@5] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 7.852871@3] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 7.858234@3] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 7.965169@4] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 7.965707@4] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 7.972485@5] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 7.978083@5] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 7.984977@5] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 7.990218@5] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 7.996834@1] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 8.002209@1] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 8.109193@6] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 8.109735@6] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 8.116484@6] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 8.122118@6] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 8.129011@6] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 8.134230@6] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 8.140880@0] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 8.146218@0] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 8.253252@7] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 8.253790@7] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 8.260569@7] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 8.266123@7] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 8.273054@7] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 8.278309@7] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 8.284912@2] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 8.290302@2] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 8.397260@5] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 8.397801@5] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 8.404553@5] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 8.410156@5] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 8.417057@5] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 8.422296@5] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 8.428971@3] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 8.434284@3] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 8.541306@4] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 8.541848@4] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 8.548636@5] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 8.554182@5] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 8.561130@5] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 8.566343@5] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 8.572989@1] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 8.578350@1] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 8.685299@6] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 8.685842@6] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 8.692615@6] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 8.698191@6] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 8.705091@6] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 8.710362@6] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 8.716980@0] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 8.722325@0] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 8.766811@0] random: nonblocking pool is initialized
[ 8.829330@7] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 8.829870@7] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 8.836615@7] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 8.842231@7] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 8.849129@7] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 8.854365@7] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 8.861017@2] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 8.866353@2] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 8.973358@5] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 8.973899@5] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 8.980686@5] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 8.986233@5] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 8.993189@5] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 8.998421@5] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 9.005024@3] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 9.010404@3] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 9.117352@4] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 9.117894@4] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 9.124643@5] FAT-fs (mmcblk1p1): bogus number of reserved sectors
[ 9.130241@5] FAT-fs (mmcblk1p1): Can't find a valid FAT filesystem
[ 9.137162@5] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 9.142389@5] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 9.149043@0] FAT-fs (mmcblk1): bogus number of reserved sectors
[ 9.154409@0] FAT-fs (mmcblk1): Can't find a valid FAT filesystem
[ 11.269443@6] fb: use ion buffer for fb memory
[ 11.270162@6] meson-fb meson-fb.16: create ion_client ffffffc063270b40, handle=ffffffc062ff3700
[ 11.276887@6] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 11.285625@6] fb: Frame buffer memory assigned at
[ 11.290091@6] fb: 0, phy: 0x0000000079300000, vir:0xffffff8001d75000, size=24900K
[ 11.290091@6]
[ 11.299423@6] fb: ---------------clear fb0 memory ffffff8001d75000
[ 11.315307@1] fb: osd[0] canvas.idx =0x40
[ 11.315332@1] fb: osd[0] canvas.addr=0x79300000
[ 11.318215@1] fb: osd[0] canvas.width=7680
[ 11.322223@1] fb: osd[0] canvas.height=3240
[ 11.326363@1] fb: osd[0] frame.width=1920
[ 11.330338@1] fb: osd[0] frame.height=1080
[ 11.386439@0] fb: osd[0] canvas.idx =0x40
[ 11.386442@0] fb: osd[0] canvas.addr=0x79300000
[ 11.386443@0] fb: osd[0] canvas.width=7680
[ 11.386445@0] fb: osd[0] canvas.height=2160
[ 11.386446@0] fb: osd[0] frame.width=1920
[ 11.386447@0] fb: osd[0] frame.height=1080
[ 11.419345@0] fb: osd[0] enable: 0 (recovery)
[ 11.433458@0] fb: osd[0] enable: 1 (recovery)
#
#
# [ 47.167074@5] [aml_is_card_insert] card OUT
[ 47.167511@5] card out
[ 47.168466@4] sd: card aaaa removed
#
# [ 191.592156@5] sd: new high speed SDHC card at address aaaa
[ 191.592192@5] sd: clock 50000000, 4-bit-bus-width
[ 191.597636@5] mmcblk1: sd:aaaa SL08G 7.40 GiB
[ 191.612170@6] mmcblk1: p1
# GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 166872
BL2 Built : 19:58:22, Aug 31 2016.
gxl g54c8aee - xiaobo.gu@droid05
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00015400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a9a00
NOTICE: BL3-1: v1.0(debug):2e39a99
NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
aml log : bl31 normal boot !
[Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
OPS=0x82
fc c2 9 21 fb ca c 14 7e b4 40 63 [0.411318 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gd267f87 (Nov 17 2016 - 19:17:36)
DRAM: 2 GiB
Relocation Offset is: 76ec9000
register usb cfg[0][1] = 0000000077f5f5d8
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073ec96b0
aml_priv->desc_buf = 0x0000000073ecb9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ece270,dt_addr=0000000073ed9270
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000080000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 80000000 1
13: data d7c00000 2c5400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=cold_boot
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 4 vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
rx version is 1.4 or below div=10
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[CANVAS]canvas init
[CANVAS]addr=0x3d851000 width=5760, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
get_cpu_id flag_12bit=1
SARADC open channel(0).
SARADC channel(0) is 0x14 (0x0~0x50).
detect upgrade key
InUsbBurn
noSof
card in
[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading aml_autoscript
** Unable to read file aml_autoscript **
reading recovery.img
11358208 bytes read in 627 ms (17.3 MiB/s)
reading dtb.img
** Unable to read file dtb.img **
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =73f4e440
copy done
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x02106540
Loading Ramdisk to 73b0b000, end 73eb6347 ... OK
Loading Device Tree to 000000001fff2000, end 000000001ffff1ca ... OK
signature:
fdt_instaboot: no instaboot image
Starting kernel ...
uboot time: 3345375 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-g6bba886 (lhh@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Thu Jan 19 17:08:41 CST 2017
[ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000@0] no prop version_code
[ 0.000000@0] bootconsole [earlycon0] enabled
[ 0.000000@0] fdt Reserved memory table:
[ 0.000000@0] linux,di: 0x000000007d300000 - 0x000000007f100000 (30 MiB)
[ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007d300000, size 30 MiB
[ 0.000000@0] linux,ion-dev: 0x0000000079300000 - 0x000000007d300000 (64 MiB)
[ 0.000000@0] linux,ppmgr: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] linux,codec_mm_cma: 0x0000000067800000 - 0x0000000073800000 (192 MiB)
[ 0.000000@0] linux,picdec: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] Reserved memory: incorrect alignment of CMA region
[ 0.000000@0] linux,codec_mm_reserved: 0x0000000075200000 - 0x0000000079300000 (65 MiB)
[ 0.000000@0] fdt Reserved memory total: 354 MiB
[ 0.000000@0] cma: Reserved 8 MiB at 74800000
[ 0.000000@0] psci: probing function IDs from device-tree
[ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc07516e000 s19968 r8192 d20992 u49152
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 510280
[ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=disabled logo=osd1,loaded,0x3d800000,1080p60hz maxcpus=8 vout=1080p60hz,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 androidboot.firstboot=0 jtag=apao androidboot.hardware=amlogic mac=86:37:20:48:cb:3e androidboot.mac=86:37:20:48:cb:3e aml_dt=gxm_q201_2g recovery_part={recovery_part} recovery_offset={recovery_offset}
[ 0.000000@0] logo: osd1
[ 0.000000@0] logo: loaded
[ 0.000000@0] logo: 0x3d800000
[ 0.000000@0] logo: 1080p60hz
[ 0.000000@0] vout_serve: 1080p60hz
[ 0.000000@0] vout_serve: enable: 1
[ 0.000000@0] logo: get hdmimode: 1080p60hz
[ 0.000000@0] logo: get cvbsmode: 576cvbs
[ 0.000000@0] tv_vout: cvbs performance line = 0
[ 0.000000@0] jtag: jtag select 2
[ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000@0] Memory: 1640852K/2077696K available (10612K kernel code, 1153K rwdata, 3884K rodata, 1263K init, 5869K bss, 436844K reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
[ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff80423cc800 ( 35 MB)
[ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc07f100000 ( 2033 MB)
[ 0.000000@0] .init : 0xffffffc001eaa000 - 0xffffffc001fe5e00 ( 1264 kB)
[ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001ea9334 ( 14501 kB)
[ 0.000000@0] .data : 0xffffffc001fe6000 - 0xffffffc002106540 ( 1154 kB)
[ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01ea8fff]
[ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000@0] arch_multi_cluster:1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[ 0.008246@0] meson_bc_timer: mclk->mux_reg =ffffff8000014990,mclk->reg =ffffff8000016994
[ 0.016825@0] Console: colour dummy device 80x25
[ 0.021096@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.031672@0] pid_max: default: 32768 minimum: 301
[ 0.036581@0] Security Framework initialized
[ 0.040787@0] SELinux: Initializing.
[ 0.044531@0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.051367@0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.061619@0] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
[ 0.065715@0] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
[ 0.072721@0] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
[ 0.079713@0] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
[ 0.090050@0] Initializing cgroup subsys debug
[ 0.091175@0] Initializing cgroup subsys freezer
[ 0.095844@0] ftrace: allocating 36489 entries in 143 pages
[ 0.149554@0] /cpus/cpu@0: Missing clock-frequency property
[ 0.149598@0] /cpus/cpu@1: Missing clock-frequency property
[ 0.155173@0] /cpus/cpu@2: Missing clock-frequency property
[ 0.160800@0] /cpus/cpu@3: Missing clock-frequency property
[ 0.166374@0] /cpus/cpu@100: Missing clock-frequency property
[ 0.172156@0] /cpus/cpu@101: Missing clock-frequency property
[ 0.177925@0] /cpus/cpu@102: Missing clock-frequency property
[ 0.183708@0] /cpus/cpu@103: Missing clock-frequency property
[ 0.189474@0] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 0.239824@0] Meson chip version = RevA (22:A - 82:0)
[ 0.258229@1] CPU1: Booted secondary processor
[ 0.278197@2] CPU2: Booted secondary processor
[ 0.298205@3] CPU3: Booted secondary processor
[ 0.318233@4] CPU4: Booted secondary processor
[ 0.338233@5] CPU5: Booted secondary processor
[ 0.358247@6] CPU6: Booted secondary processor
[ 0.378272@7] CPU7: Booted secondary processor
[ 0.378365@0] Brought up 8 CPUs
[ 0.407181@0] SMP: Total of 8 processors activated.
[ 0.420682@2] sched: registering cpufreq notifiers for scale-invariant loads
[ 0.422205@2] instabooting: 0
[ 0.434371@2] pinctrl core: initialized pinctrl subsystem
[ 0.435067@2] regulator-dummy: no parameters
[ 0.439351@2] NET: Registered protocol family 16
[ 0.445245@3] ramoops: using module parameters
[ 0.448231@2] console [pstore-1] enabled
[ 0.451554@2] pstore: Registered ramoops as persistent store backend
[ 0.457930@2] ramoops: attached 0x100000@0x7300000, ecc: 0/0
[ 0.464550@3] cpuidle: using governor menu
[ 0.468001@3] aml_vdac_init: module init
[ 0.471889@2] register canvas platform driver
[ 0.476169@2] register rdma platform driver
[ 0.482123@2] vdso: 2 pages (1 code, 1 data) at base ffffffc001ff0000
[ 0.486776@2] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.494100@2] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.501008@2] software IO TLB [mem 0x64400000-0x64800000] (4MB) mapped at [ffffffc064400000-ffffffc0647fffff]
[ 0.509993@2] Serial: AMBA PL011 UART driver
[ 0.514862@3] aml_i2c version: 20140813
[ 0.518396@3] i2c-core: driver [pmu4] using legacy resume method
[ 0.524376@3] codec_mm:codec_mm_module_init
[ 0.528633@2] aml_watch_point_probe, in
[ 0.532683@2] gxbb_mpll_clk: register mpll_clk_out0 success done
[ 0.538279@2] gxbb_mpll_clk: register mpll_clk_out1 success done
[ 0.544295@2] gxbb_mpll_clk: register mpll_clk_out2 success done
[ 0.550544@2] clk_sys: register PLL sys_pll success done
[ 0.555676@2] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
[ 0.561039@2] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
[ 0.566168@2] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
[ 0.571686@2] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
[ 0.577629@2] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
[ 0.583597@2] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
[ 0.589442@2] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
[ 0.595309@2] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
[ 0.601166@2] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
[ 0.607063@2] gxl_clk: clock initialization complete
[ 0.612236@2] clkmsr: Gxl msr_clk_reg0=ffffff800003c75c,msr_clk_reg2=ffffff800003e764
[ 0.622498@2] aml_iomap: amlogic iomap probe done
[ 0.625278@3] pinmux-gxl c1109880.pinmux: Init pinux probe!
[ 0.631184@3] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
[ 0.637462@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.644945@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ 0.653178@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.661067@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
domain-0 init dvfs: 4
domain-1 init dvfs: 4
[ 0.681182@2] codec_mm has 2 memory regions
[ 0.681252@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.687887@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.696463@2] codec_mm has 2 memory regions
[ 0.700562@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.708595@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.719162@2] vpu: driver version: v02
[ 0.720869@2] vpu: load vpu_clk: 666667000Hz(7)
[ 0.725494@2] vpu: vpu_probe OK
[ 0.730303@2] tv_vout: tvout_probe
[ 0.731963@2] tv_vout: major number 254 for disp
[ 0.736590@2] vout_notify: vout_register_server
[ 0.741155@2] tv_vout: register tv module server ok
[ 0.746147@2] tv_vout: tvout_probe OK
[ 0.750366@2] canvas_probe reg=00000000c8838000,size=400
[ 0.755088@2] canvas maped reg_base =ffffff800009a000
[ 0.764481@2] rdma_probe
[ 1.077969@2] bio: create slab <bio-0> at 0
[ 1.079204@3] SCSI subsystem initialized
[ 1.081097@2] usbcore: registered new interface driver usbfs
[ 1.086457@2] usbcore: registered new interface driver hub
[ 1.091897@3] usbcore: registered new device driver usb
[ 1.097982@2] i2c-gpio i2c_gpio.38: using pins 172 (SDA) and 173 (SCL)
[ 1.103713@3] Linux video capture interface: v2.00
[ 1.108635@3] pps_core: LinuxPPS API ver. 1 registered
[ 1.113528@3] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 1.122995@3] PTP clock support registered
[ 1.128199@2] hdmitx: system: amhdmitx_init
[ 1.131192@2] hdmitx: system: Ver: 2014May6
[ 1.135566@2] hdmitx: system: amhdmitx_probe
[ 1.140030@2] hdmitx: system: not find match init-data
[ 1.144842@2] hdmitx: system: not find match pwr-ctl
[ 1.149928@2] hdmitx hpd irq = 89
[ 1.153661@2] hdmitx20: Mapped PHY: 0xc0800000
[ 1.157624@2] hdmitx20: Mapped PHY: 0xc1104400
[ 1.162106@2] hdmitx20: Mapped PHY: 0xc8100000
[ 1.166542@2] hdmitx20: Mapped PHY: 0xc8834000
[ 1.171002@2] hdmitx20: Mapped PHY: 0xc883a000
[ 1.175471@2] hdmitx20: Mapped PHY: 0xc883c000
[ 1.179931@2] hdmitx20: Mapped PHY: 0xd0100000
[ 1.184390@2] hdmitx20: Mapped PHY: 0xda83a000
[ 1.188865@2] hdmitx: alread display in uboot 0x10
[ 1.193683@2] avmute set to 1
[ 1.197058@0] vout_serve: vout_init_module
[ 1.201056@0] tv_vout: tv_set_current_vmode[759]fps_target_mode=16
[ 1.206972@0] hdmitx: system: irq 80000002
[ 1.211099@0] tv_vout: mode is 16,sync_duration_den=1,sync_duration_num=60
[ 1.217994@0] tv_vout: already display in uboot
[ 1.222572@0] vout_serve: vinfo mode is: 1080p60hz
[ 1.227351@0] vout_serve: init mode 1080p60hz
[ 1.231868@3] vout_serve: create vout attribute OK
[ 1.236540@3] vout_serve: meson_vout_probe OK
[ 1.241145@0] logo: logo_init
[ 1.244322@0] osd_rdma: osd_rdma_init: rdma_table p=0x74841000,op=0x74841000 , v=0xffffff800009e000
[ 1.252991@0] osd_rdma: osd rdma request irq as second interrput function!
[ 1.260439@3] Advanced Linux Sound Architecture Driver Initialized.
[ 1.266899@0] Bluetooth: Core ver 2.18
[ 1.270108@0] NET: Registered protocol family 31
[ 1.274638@0] Bluetooth: HCI device and connection manager initialized
[ 1.281200@0] Bluetooth: HCI socket layer initialized
[ 1.286243@0] Bluetooth: L2CAP socket layer initialized
[ 1.291546@0] Bluetooth: SCO socket layer initialized
[ 1.297064@0] cfg80211: Calling CRDA to update world regulatory domain
[ 1.303257@3] NetLabel: Initializing
[ 1.306762@3] NetLabel: domain hash size = 128
[ 1.311263@3] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.316478@3] NetLabel: unlabeled traffic allowed by default
[ 1.324483@0] Switched to clocksource arch_sys_counter
[ 1.374387@1] [amlatvdemod..]aml_atvdemod_init.
[ 1.374564@1] NET: Registered protocol family 2
[ 1.378398@1] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.385497@1] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 1.392412@1] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.399041@2] TCP: reno registered
[ 1.402327@2] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 1.408583@2] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 1.415445@2] NET: Registered protocol family 1
[ 1.420042@2] RPC: Registered named UNIX socket transport module.
[ 1.425868@2] RPC: Registered udp transport module.
[ 1.430754@2] RPC: Registered tcp transport module.
[ 1.435673@2] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.442524@2] aml_wifi wifi.33: [wifi_dev_probe] no power_on_pin2
[ 1.448442@2] aml_wifi wifi.33: [wifi_dev_probe] set pwm as 32k output
[ 1.455050@2] aml_wifi wifi.33: [wifi_dev_probe] dhd_static_buf setup
[ 1.461531@2] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem: WIFI MEM Allocated
[ 1.469118@2] aml_wifi wifi.33: [wifi_dev_probe] interrupt_pin=241
[ 1.475301@2] aml_wifi wifi.33: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
[ 1.482731@2] aml_wifi wifi.33: [wifi_dev_probe] power_on_pin=240
[ 1.488861@2] aml_wifi wifi.33: [wifi_dev_probe] clock_32k_pin=0
[ 1.495254@0] aml_wifi wifi.33: [wifi_setup_dt] wifi_setup_dt
[ 1.500705@0] aml_wifi wifi.33: [wifi_setup_dt] interrupt_pin(241)
[ 1.506941@0] aml_wifi wifi.33: [wifi_setup_dt] power_on_pin(240)
[ 1.513397@1] Unpacking initramfs...
[ 1.534620@0] hdmitx: plugin
[ 1.651032@1] Freeing initrd memory: 3756K (ffffffc073b0b000 - ffffffc073eb6000)
[ 1.657963@2] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 1.659458@2] audit: initializing netlink subsys (disabled)
[ 1.665030@2] audit: type=2000 audit(1.570:1): initialized
[ 1.671382@2] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.671470@0] hdmitx: edid: check sum valid
[ 1.671472@0] hdmitx: edid: check sum valid
[ 1.671475@0] hdmitx: edid: blk0 raw data
[ 1.671515@0] 00ffffffffffff001e6de37689bb02000b18010380502278eaca95a6554ea126
[ 1.671515@0] 0f50542108007140818081c0a9c0b300d1c0810001019d6770a0d0a022503020
[ 1.671515@0] 3a00204f3100001a000000fd00383d1e5a1e000a202020202020000000fc004c
[ 1.671515@0] 4720554c545241574944450a000000000000000000000000000000000000017c
[ 1.671515@0]
[ 1.671515@0]
[ 1.671517@0] hdmitx: edid: blk1 raw data
[ 1.671556@0] 020317f14410040301230907078301000065030c0010009f3d70a0d0a0155030
[ 1.671556@0] 203a00204f3100001a7e4800e0a0381f4040403a00204f31000018011d007251
[ 1.671556@0] d01e206e285500204f3100001e8c0ad08a20e02d10103e9600204f3100001800
[ 1.671556@0] 0000ff003431314b4b484e35393038310a0000000000000000000000000000ce
[ 1.671556@0]
[ 1.671556@0]
[ 1.671560@0] EDID Parser:
[ 1.671605@0] hdmitx: edid: find IEEEOUT
[ 1.671628@0]
[ 1.671629@0] hdmitx: edid: check sum valid
[ 1.671630@0] hdmitx: edid: check sum valid
[ 1.671635@0] hdmitx: update RX hdr info 0
[ 1.673657@0] hdmitx: ddc rd8b error 0x3a 0x00 0x00
[ 1.675701@0] [RX]-receive ksv list len:1,depth:1,cas:0,dev:0
[ 1.675708@0] hdmitx: video: get current mode: 1080p60hz
[ 1.675709@0] hdmitx: update rx hdr info 0
[ 1.675725@0] hdmitx: get ext_name (null)
[ 1.675731@0] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 16
[ 1.675736@0] hdmtix: set audio
[ 1.675746@0] hdmitx tx_aud_src = 0
[ 1.675774@0] hdmitx: fs = 0, cd = 4, tmds_clk = 148500
[ 1.675776@0] hdmitx aud_n_para = 6144
[ 1.675796@0] hdmitx set channel status
[ 1.837209@0] VFS: Disk quotas dquot_6.5.2
[ 1.837494@1] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.847743@1] NFS: Registering the id_resolver key type
[ 1.847810@1] Key type id_resolver registered
[ 1.852014@1] Key type id_legacy registered
[ 1.856260@1] NTFS driver 2.1.30 [Flags: R/O].
[ 1.861114@0] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.868852@1] fuse init (API version 7.22)
[ 1.872754@0] msgmni has been set to 3612
[ 1.878025@0] NET: Registered protocol family 38
[ 1.881114@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 1.888350@0] io scheduler noop registered
[ 1.892473@0] io scheduler deadline registered
[ 1.897191@0] io scheduler cfq registered (default)
[ 1.951838@0] meson-rng c8834000.rng: hwrng registered
[ 1.956403@0] loop: module loaded
[ 1.957042@0] zram: Created 1 device(s) ...
[ 1.959995@0] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.967566@0] tun: Universal TUN/TAP device driver, 1.6
[ 1.970852@0] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 2.102900@1] libphy: stmmac: probed
[ 2.102937@1] eth0: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[ 2.107485@1] eth0: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07)
[ 2.113916@0] PPP generic driver version 2.4.2
[ 2.118139@1] PPP BSD Compression module registered
[ 2.122785@1] PPP Deflate Compression module registered
[ 2.128067@1] PPP MPPE Compression module registered
[ 2.133021@1] NET: Registered protocol family 24
[ 2.137895@0] usbcore: registered new interface driver asix
[ 2.143461@0] usbcore: registered new interface driver ax88179_178a
[ 2.149723@1] usbcore: registered new interface driver cdc_ether
[ 2.155764@0] usbcore: registered new interface driver net1080
[ 2.161586@0] usbcore: registered new interface driver cdc_subset
[ 2.167740@1] usbcore: registered new interface driver zaurus
[ 2.173516@0] usbcore: registered new interface driver cdc_ncm
[ 2.179611@1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.185986@1] ehci-h20ahb: H20AHB-EHCI Host Controller driver
[ 2.192044@0] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.198617@1] usbcore: registered new interface driver cdc_acm
[ 2.203985@1] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.212390@0] usbcore: registered new interface driver usb-storage
[ 2.218758@1] usbcore: registered new interface driver usbserial
[ 2.225260@1] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff80000da000
[ 2.235494@0] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
[ 2.242019@0] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff80000ee080
[ 2.253389@0] mousedev: PS/2 mouse device common for all mice
[ 2.259066@0] usbcore: registered new interface driver xpad
[ 2.264233@0] i2c /dev entries driver
[ 2.268086@0] usbcore: registered new interface driver uvcvideo
[ 2.273671@0] USB Video Class driver (1.1.1)
[ 2.278907@0] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: [email protected]
[ 2.286708@0] Bluetooth: HCI UART driver ver 2.2
[ 2.291255@0] Bluetooth: HCI H4 protocol initialized
[ 2.296651@0] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
[ 2.303935@0] cpu cpu4: bL_cpufreq_init: CPU 4 initialized
[ 2.307451@0] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
[ 2.315242@1] CPUidle arm64: cpuidle init start!!
[ 2.320507@1] @@@@@@@@@@_____2______in dia_init()
[ 2.324387@1] ATVR driver - init called!
[ 2.328468@0] usbcore: registered new interface driver usbhid
[ 2.334094@0] usbhid: USB HID core driver
[ 2.338577@0] ashmem: initialized
[ 2.341652@0] logger: created 256K log 'log_main'
[ 2.346346@1] logger: created 256K log 'log_events'
[ 2.351215@0] logger: created 256K log 'log_radio'
[ 2.356105@0] logger: created 256K log 'log_system'
[ 2.361976@0] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff80000fc4c0
[ 2.368028@0] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
[ 2.383010@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
[ 2.385674@0] console [ttyS0] enabled
[ 2.385674@0] console [ttyS0] enabled
[ 2.392896@0] bootconsole [earlycon0] disabled
[ 2.392896@0] bootconsole [earlycon0] disabled
[ 2.402076@1] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff80000fe4c0
[ 2.408732@1] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
[ 2.418490@0] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff]
[ 2.427955@0] meson-gpu-clkgen: probe of c883c000.gpu_clk failed with error -16
[ 2.435422@1] hdmitx: system: hdmitx_hdcp_init
[ 2.439712@0] ESM HLD: Initializing...
[ 2.443249@0] ESM HLD: Registering device range 'esm'...
[ 2.448547@0] ESM HLD: Device range 'esm' has been registered.
[ 2.454288@0] ESM HLD: Creating class /sys/class/elliptic...
[ 2.460027@0] ESM HLD: The class /sys/class/elliptic has been created.
[ 2.466370@0] ESM HLD: Creating device 'esm'...
[ 2.470978@1] ESM HLD: Device 'esm' has been created.
[ 2.475877@1] ESM HLD: Done initializing the HLD driver.
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[ 2.497105@0] aml_vrtc rtc.32: rtc core: registered aml_vrtc as rtc0
[ 2.498510@0] secmon has 1 memory regions
[ 2.501815@0] secmon: share in base: 0xffffff800011a000, share out base: 0xffffff800011c000
[ 2.510108@0] secmon secmon.4: assigned reserved memory node linux,secmon ok
[ 2.517051@0] secmon: probe done
[ 2.520565@0] storage: storage in base: 0xffffff8001800000
[ 2.525734@0] storage: storage out base: 0xffffff8001880000
[ 2.531188@0] storage: storage block base: 0xffffff8001900000
[ 2.536888@0] storage: probe done!
[ 2.540817@0] aml_sd_emmc_probe: line 3578
[ 2.544303@0] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
[ 2.554210@0] aml_sd_emmc_reg_init 1146
[ 2.557595@0] get property: ocr_avail, value:0x00200080
[ 2.563965@0] get property: f_min, value:300000
[ 2.570116@0] get property: f_max, value:100000000
[ 2.576497@0] get property: max_req_size, value:0x00020000
[ 2.582942@0] get property: pinname, str:emmc
[ 2.588736@0] get property: card_type, value:1
[ 2.594444@0] get property: gpio_dat3, str:
[ 2.599852@0] get property: hw_reset, str:
[ 2.605322@0] emmc:pdata->caps = c0000d47
[ 2.609266@0] emmc:pdata->caps2 = 18060
[ 2.613053@0] storage 1, boot 1
[ 2.616158@0] get_storage_dev return 1
[ 2.654490@1] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.654712@1] aml_sd_emmc_probe: line 3578
[ 2.659107@1] aml_sd_emmc_reg_init 1146
[ 2.662580@1] get property: ocr_avail, value:0x00200080
[ 2.669012@1] get property: f_min, value:400000
[ 2.675136@1] get property: f_max, value:100000000
[ 2.681506@1] get property: max_req_size, value:0x00020000
[ 2.687980@1] get property: irq_in, value:3
[ 2.693667@1] get property: irq_out, value:5
[ 2.699374@1] get property: gpio_cd, str:
[ 2.704799@1] get property: pinname, str:sd
[ 2.710401@1] get property: jtag_pin, str:
[ 2.715841@1] get property: card_type, value:5
[ 2.721527@1] get property: gpio_dat3, str:
[ 2.726976@1] sd:pdata->caps = 7
[ 2.730150@1] sd:pdata->caps2 = 0
[ 2.764689@0] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.764733@4] [aml_is_card_insert] card IN
[ 2.769029@0] aml_sd_emmc_probe: line 3578
[ 2.773355@0] aml_sd_emmc_reg_init 1146
[ 2.776839@0] get property: ocr_avail, value:0x00200080
[ 2.783246@0] get property: f_min, value:400000
[ 2.789472@0] get property: f_max, value:200000000
[ 2.795759@0] get property: max_req_size, value:0x00020000
[ 2.802224@0] get property: pinname, str:sdio
[ 2.808094@0] get property: card_type, value:3
[ 2.813731@0] sdio:pdata->caps = 7810f
[ 2.817406@0] sdio:pdata->caps2 = 0
[ 2.854494@0] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.855026@0] ion_dev has 1 memory regions
[ 2.861233@3] emmc: BKOPS_EN bit is not set
[ 2.866074@4] normal card in
[ 2.871998@3] emmc: trying cali 0-th time(s)
[ 2.875007@0] fb: osd_init_module
[ 2.875155@0] fb: viu vsync irq: 35
[ 2.877362@0] fb: failed to init reserved memory
[ 2.881938@0] fb: osd_probe vinfo:ffffffc002086d98
[ 2.881948@3] emmc: delay[0]= 4600 padding= 2, bidx=4
[ 2.881950@3] emmc: delay[1]= 4400 padding= 3, bidx=4
[ 2.881952@3] emmc: delay[2]= 4400 padding= 3, bidx=4
[ 2.881954@3] emmc: delay[3]= 4800 padding= 1, bidx=4
[ 2.881956@3] emmc: delay[4]= 4800 padding= 1, bidx=4
[ 2.881958@3] emmc: delay[5]= 4600 padding= 2, bidx=4
[ 2.881960@3] emmc: delay[6]= 4600 padding= 2, bidx=4
[ 2.881962@3] emmc: delay[7]= 4800 padding= 1, bidx=4
[ 2.881964@3] emmc: calibration result @ 0: max(4800), min(4400)
[ 2.881967@3] emmc: line_delay =0x1100221, max_cal_result =4800
[ 2.881968@3] emmc: base_index_max 4, base_index_min 4
[ 2.881974@3] emmc: clk 100000000 SDR mode tuning start
[ 2.948814@0] fb: init fbdev bpp is:32
[ 2.952950@3] emmc: rx_tuning_result[0] = 10
[ 2.957250@3] emmc: rx_tuning_result[1] = 10
[ 2.961456@3] emmc: rx_tuning_result[2] = 10
[ 2.965693@3] emmc: rx_tuning_result[3] = 10
[ 2.969911@3] emmc: rx_tuning_result[4] = 10
[ 2.972147@0] fb: osd probe OK
[ 2.972382@0] ge2d: ge2d_init_module
[ 2.972391@0] ge2d: ge2d_dev major:243
[ 2.972741@0] ge2d: ge2d clock is 400 MHZ
[ 2.972745@0] ge2d: ge2d: pdev=ffffffc065288000, irq=182, rstc=0xffffffc06421d900, clk=ffffffc065278800
[ 2.972800@0] ge2d: mapped phy: 0xd0160000
[ 2.972805@0] ge2d: ge2d start monitor
[ 2.972873@2] ge2d: ge2d workqueue monitor start
[ 2.973065@2] sysled: module init
[ 2.973182@2] sysled: led_gpio = 154
[ 2.973183@2] sysled: active_low = 0
[ 2.973337@0] sysled: module probed ok
[ 2.973736@0] pwmled: module init
[ 2.973823@0] codec:Amlogic A/V streaming port init
[ 2.975205@2] codec:get gate demux control ok ffffffc06332c200
[ 2.975209@2] codec:get gate parser_top control ok ffffffc06332c800
[ 2.975213@2] codec:get gate vpu_intr control ok ffffffc06332ce00
[ 2.975219@2] codec:get gate vdec control ok ffffffc06332cdc0
[ 2.975842@2] codec:[tsync_pcr_init]init success.
[ 2.975844@2] codec:amvideocap_init_module
[ 2.975966@2] codec:amvideocap_probe,amvideocap
[ 2.975968@2] codec:use cma buf.
[ 2.975970@2] codec:amvideocap_dev_register
[ 2.977802@0] amvenc_avc_probe -- reserved memory config fail.
[ 2.977805@0] amvenc_avc - cma memory pool size: 40 MB
[ 2.977825@0] encode_wq_init.
[ 2.977830@0] encode start monitor.
[ 2.977888@2] encode workqueue monitor start.
[ 2.978294@0] jpegenc module init
[ 2.978596@2] codec:picdec_driver_probe called.
[ 2.978599@2] picdec has 1 memory regions
[ 2.978621@2] codec:picdec_driver_probe done.
[ 2.979542@2] codec:create_ge2d_work_queue video task ok
[ 2.979925@0] codec:used fix clk for vdec clk source!
[ 2.979931@0] codec:register clk_set_setting cpu[34]
[ 2.980266@0] vpu_init
[ 2.980439@0] vpu_probe
[ 2.980442@0] HevcEnc reserved memory config fail.
[ 2.980446@0] HevcEnc - cma memory pool size: 64 MB
[ 2.980449@0] HevcEnc - wave420l_irq: 219
[ 2.980489@0] vpu base address get from platform driver physical base addr=0xc8810000, virtual base=0xffffff8000258000
[ 2.980777@0] success to probe vpu device with video memory from cma
[ 2.980925@2] DI: di_module_init ok.
[ 2.980929@2] DI: di_module_init: major 236
[ 2.981136@0] DI: di_probe
[ 2.981246@2] deinterlace has 1 memory regions
[ 2.981276@2] deinterlace deinterlace.26: assigned reserved memory node linux,di ok
[ 2.981297@2] di_irq:78,timerc_irq:38
[ 3.189949@0] rdma_register, rdma_table_addr ffffff800016c000 rdma_table_addr_phy 74848000 reg_buf ffffffc0630d4000
[ 3.200213@0] rdma_register success, handle 1 table_size 8192
[ 3.205932@0] DI: di_probe allocate rdma channel 1.
[ 3.210717@0] DI: DI hw version 2.
[ 3.214087@0] 0x000000db:Y=db,U=0,V=0
[ 3.217992@3] emmc: rx_tuning_result[5] = 10
[ 3.218009@0] 0x000000dc:Y=dc,U=0,V=0
[ 3.218011@0] 0x000000dd:Y=dd,U=0,V=0
[ 3.218013@0] 0x000000de:Y=deeU=0,V=0
[ 3.218014@0] 0x000000df:Y=df,U=0,V=0
[ 3.218016@0] 0x000000e0:Y=e0,U=0,V=0
[ 3.218018@0] 0x000000e1:Y=e1,U=0,V=0
[ 3.218020@0] 0x000000e2:Y=e2,U=0,V=0
[ 3.218021@0] 0x000000e3:Y=e3,U=0,V=0
[ 3.218023@0] 0x000000f0:Y=f0,U=0,V=0
[ 3.218028@0] 0x000000f1:Y=f1,U=0,V=0
[ 3.218030@0] 0x000000f2:Y=f2,U=0,V=0
[ 3.218032@0] 0x000000f3:Y=f3,U=0,V=0
[ 3.218033@0] 0x000000f4:Y=f4,U=0,V=0
[ 3.218035@0] 0x000000f5:Y=f5,U=0,V=0
[ 3.218036@0] 0x000000f6:Y=f6,U=0,V=0
[ 3.218040@0] 0x000000f7:Y=f7,U=0,V=0
[ 3.218042@0] 0x000000f8:Y=f8,U=0,V=0
[ 3.218044@0] 0x000000f9:Y=f9,U=0,V=0
[ 3.218046@0] 0x000000fa:Y=fa,U=0,V=0
[ 3.218047@0] 0x000000fb:Y=fb,U=0,V=0
[ 3.218049@0] 0x000000fc:Y=fc,U=0,V=0
[ 3.218186@0] DI: di_probe here.
[ 3.218563@0] efusekeynum: 4
[ 3.218571@0] efusekeyname: mac offset: 0 size: 6
[ 3.218576@0] efusekeyname: mac_bt offset: 6 size: 6
[ 3.218581@0] efusekeyname: mac_wifi offset: 12 size: 6
[ 3.218586@0] efusekeyname: usid offset: 18 size: 16
[ 3.218829@0] efuse efuse.10: probe OK!
[ 3.219187@2] key unify config unifykey-num is 14
[ 3.219228@2] key unify fact unifykey-num is 14
[ 3.219232@2] aml_unifykeys_probe:1273=============unifykey_devno:ea00000
[ 3.219439@2] 6unifykey: device unifykeys created ok
[ 3.219557@0] 6aml_unifykeys_init done!
[ 3.219559@0] PPMGRDRV: warn: ppmgr module init func called
[ 3.219677@0] PPMGRDRV: err: ppmgr_driver_probe called
[ 3.219680@0] ppmgr has 1 memory regions
[ 3.219707@0] PPMGRDRV: info: ppmgr_dev major:233
[ 3.219935@0] PPMGRDRV: info: ppmgr_probe done
[ 3.220339@0] amlogic rfkill init
[ 3.220443@0] enter bt_probe of_node
[ 3.220459@0] not get gpio_en
[ 3.220745@0] power on valid level is high
[ 3.220745@0] Bluetooth: BlueSleep Mode Driver Ver 1.2
[ 3.221173@2] ionvideo-000: V4L2 device registered as video13
[ 3.221174@2] ionvid: info: Video Technology Magazine Ion Video
[ 3.221176@2] ionvid: info: Capture Board ver 1.0 successfully loaded
[ 3.221184@2] audio_dsp: [dsp]register dsp to char divece(257)
[ 3.221763@0] amaudio: amaudio: driver amaudio succuess!
[ 3.222047@2] amlvid:err: amlvideo_init called
[ 3.222048@2] amlvid:err: amlvideo_create_instance called
[ 3.222051@2] amlvid:err: v4l2_dev.name=:amlvideo-000
[ 3.222172@1] amlvideo-000: V4L2 device registered as video10
[ 3.222531@1] vdin_drv_init: major 232
[ 3.222839@1] vdin_drv_init: vdin driver init done
[ 3.222843@1] tvafe_drv_init: major 231
[ 3.223106@1] tvafe: tvafe_init.
[ 3.223369@1] [RX]-hdmirx: hdmirx_init.
[ 3.223372@1] ESM HLD: Initializing...
[ 3.223374@1] ESM HLD: Registering device range 'esm_rx'...
[ 3.223384@1] ESM HLD: Device range 'esm_rx' has been registered.
[ 3.223385@1] ESM HLD: Creating class /sys/class/elliptic_rx...
[ 3.223453@0] ESM HLD: The class /sys/class/elliptic_rx has been created.
[ 3.223454@0] ESM HLD: Creating device 'esm_rx'...
[ 3.223573@1] ESM HLD: Device 'esm_rx' has been created.
[ 3.223574@1] ESM HLD: Done initializing the HLD driver.
[ 3.223576@1] [viuin..]viuin_init_module viuin module init
[ 3.223957@1] [viuin..]viuin_probe probe ok.
[ 3.224029@0] module init
[ 3.224144@0]
[ 3.224144@0] VECM probe start
[ 3.224405@0] aml_vecm_probe: ok
[ 3.225306@1] saradc c1108680.saradc: initialized by BL30
[ 3.225316@1] saradc c1108680.saradc: calibration start:
[ 3.225362@1] saradc c1108680.saradc: nominal=0, value=3
[ 3.225408@1] saradc c1108680.saradc: nominal=256, value=250
[ 3.225452@1] saradc c1108680.saradc: nominal=512, value=499
[ 3.225496@1] saradc c1108680.saradc: nominal=768, value=747
[ 3.225540@1] saradc c1108680.saradc: nominal=1023, value=996
[ 3.225543@1] saradc c1108680.saradc: calibration end: coef=4219
[ 3.225715@0] remote: Driver init
[ 3.225786@0] remote: platform_data g_remote_ao_offset=580
[ 3.225788@0] remote: platform_data irq =228
[ 3.225816@0] remote: set drvdata completed
[ 3.225832@0] remote: device_create_file completed
[ 3.226128@0] input: aml_keypad as /devices/meson-remote.12/input/input0
[ 3.226369@0] remote: input_register_device completed
[ 3.226413@0] remote: set_remote_mode[74]
[ 3.226438@0] remote: remote config major:228
[ 3.226613@0] remote: physical address:0x6309a000
[ 3.227187@0] gpio-key gpio_keypad.48: gpio_key: 0 name(power) pin()
[ 3.227192@0] gpio-key gpio_keypad.48: amlogic_gpio_name_map_num pin 0!::
[ 3.227207@0] gpio-key gpio_keypad.48: gpio_key: 0 power(147)
[ 3.227234@0] gpio-key gpio_keypad.48: start setup_timer
[ 3.227242@0] gpio-key gpio_keypad.48: power key(116) registed.
[ 3.227434@1] input: gpio_keypad as /devices/gpio_keypad.48/input/input1
[ 3.227559@0] gpio-key gpio_keypad.48: gpio keypad register input device completed.
[ 3.227568@0] input input1: gpio keypad major:227
[ 3.228689@1] Sensor: lsm303d_init
[ 3.228905@0] Sensor: stk8313_init
[ 3.228984@1] Sensor: stk831x_init
[ 3.229057@0] Sensor: mxc622x_acc_init
[ 3.229130@1] Sensor: mxc6255xc_acc_init
[ 3.229276@1] Sensor: l3gd20_gyr_init
[ 3.230207@1] aml dvb init
[ 3.230598@1] Amlogic Demod DVB-T/C DebugIF Init
[ 3.230793@1] Amlogic Demod DVB-T/C DebugIF Init ok----------------
[ 3.231585@1] jtag: module init
[ 3.231769@0] jtag: pinctrl setup apao
[ 3.231771@0] jtag: set state 2
fuse_pw_en: 0x3
WARNING! efuse bits is disabled
Enable A53 JTAG cluster 0 to AO
[ 3.730252@0] input input1: key 116 up
[ 3.730283@0] jtag: module probed ok
[ 3.732302@3] emmc: rx_tuning_result[6] = 10
[ 3.732319@1] cpuinfo: probe done
[ 3.732664@1] defendkey c8834500.defendkey: defendkey_devno:df00000
[ 3.732888@1] defendkey c8834500.defendkey: defendkey: device defendkey created ok
[ 3.733060@2] defendkey: driver init
[ 3.733714@1] input: cec_input as /devices/virtual/input/input2
[ 3.733937@2] cectx aocec: no hdmirx reg resource
[ 3.733940@2] cectx aocec: no hhi reg resource
[ 3.734034@2] cectx aocec: can't find hdmirx
[ 3.735047@2] cec: wake up flag:0
[ 3.736059@1] aml_aes_dma c883e000.aml_aes: Aml AES_dma
[ 3.736629@2] aml_tdes_dma c883e000.aml_tdes: Aml TDES_dma
[ 3.737257@1] aml_sha_dma c883e000.aml_sha: Aml SHA1/SHA224/SHA256 dma
[ 3.737783@2] usbcore: registered new interface driver snd-usb-audio
[ 3.739227@2] aml_codec_T9015 c8832000.t9015: aml_T9015_audio_codec_probe
[ 3.741235@1] aml_pcm_dai: pcm mode detection =1
[ 3.741609@2] aml_spdif_dai: enterd aml_spdif_play,set_clock:-1,sample_rate=4
[ 3.741629@2] aml_spdif_dai: set normal 512 fs /4 fs
[ 3.741637@2] aml_audio_hw: IEC958 16bit
[ 3.741641@2] hdmitx: audio: aout notify rate 48000
[ 3.741643@2] hdmitx: audio: aout notify size 16
[ 3.741645@2] hdmitx: audio: aout notify format CT_PCM
[ 3.741647@2] hdmtix: set audio
[ 3.741660@2] hdmitx tx_aud_src = 0
[ 3.741686@2] hdmitx: fs = 3, cd = 4, tmds_clk = 148500
[ 3.741688@2] hdmitx aud_n_para = 6144
[ 3.741707@2] hdmitx set channel status
[ 3.741767@2] hdmitx: audio: Audio Type: PCM
[ 3.741769@2] hdmitx: audio: set audio param
[ 3.874026@3] emmc: rx_tuning_result[7] = 10
[ 3.876565@3] emmc: rx_tuning_result[8] = 10
[ 3.880303@3] emmc: best_win_start =0, best_win_size =9
[ 3.885434@3] emmc: sd_emmc_regs->gclock=0x100024a,sd_emmc_regs->gadjust=0x42000
[ 3.892759@3] emmc: gclock =0x100024a, gdelay=0x1100221, gadjust=0x42000
[ 3.899743@3] emmc: new HS200 MMC card at address 0001
[ 3.904495@3] emmc: clock 100000000, 8-bit-bus-width
[ 3.909965@1] mmcblk0: emmc:0001 NCard 14.4 GiB
[ 3.914444@1] mmcblk0boot0: emmc:0001 NCard partition 1 4.00 MiB
[ 3.920508@1] mmcblk0boot1: emmc:0001 NCard partition 2 4.00 MiB
[ 3.926546@1] mmcblk0rpmb: emmc:0001 NCard partition 3 4.00 MiB
[ 3.933198@1] mmcblk0: unknown partition table
[ 3.937592@2] [mmc_read_partition_tbl] mmc read partition OK!
[ 3.942524@2] add_emmc_partition
[ 3.945936@1] [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
[ 3.945960@0] aml_snd_card: headphone detection disable=1
[ 3.945963@0] aml_snd_card: no spk event delay time set
[ 3.964918@2] [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
[ 3.965049@0] aml_snd_m8_card aml_m8_snd.47: T9015-audio-hifi <-> I2S.40 mapping ok
[ 3.965553@0] aml_snd_m8_card aml_m8_snd.47: dit-hifi <-> SPDIF.41 mapping ok
[ 3.965625@0] aml_pcm: enter aml_pcm_new dai->name: PCM.42 dai->id: 0
[ 3.965714@0] aml_snd_m8_card aml_m8_snd.47: pcm2bt-pcm <-> PCM.42 mapping ok
[ 3.965738@0] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTL
[ 3.965742@0] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
[ 3.965745@0] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTR
[ 3.965749@0] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
[ 3.967494@3] GACT probability NOT on
[ 3.967504@3] Mirror/redirect action on
[ 3.967507@3] u32 classifier
[ 3.967508@3] Actions configured
[ 3.967512@3] Netfilter messages via NETLINK v0.30.
[ 3.967558@3] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 3.968004@0] ctnetlink v0.93: registering with nfnetlink.
[ 3.968494@3] xt_time: kernel timezone is -0000
[ 3.968574@3] ipip: IPv4 over IPv4 tunneling driver
[ 4.073570@0] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 4.073719@3] [mmcblk0p03] cache offset 0x000006c00000, size 0x000020000000
[ 4.073879@2] [mmcblk0p04] env offset 0x000027400000, size 0x000000800000
[ 4.074025@3] [mmcblk0p05] logo offset 0x000028400000, size 0x000002000000
[ 4.074154@3] [mmcblk0p06] recovery offset 0x00002ac00000, size 0x000002000000
[ 4.074276@3] [mmcblk0p07] rsv offset 0x00002d400000, size 0x000000800000
[ 4.074392@3] [mmcblk0p08] tee offset 0x00002e400000, size 0x000000800000
[ 4.074569@3] [mmcblk0p09] crypt offset 0x00002f400000, size 0x000002000000
[ 4.074702@3] [mmcblk0p10] misc offset 0x000031c00000, size 0x000002000000
[ 4.074825@3] [mmcblk0p11] instaboot offset 0x000034400000, size 0x000020000000
[ 4.074937@3] [mmcblk0p12] boot offset 0x000054c00000, size 0x000002000000
[ 4.075054@3] [mmcblk0p13] system offset 0x000057400000, size 0x000080000000
[ 4.075170@3] [mmcblk0p14] data offset 0x0000d7c00000, size 0x0002c5400000
[ 4.075199@3] card key: card_blk_probe.
[ 4.075203@3] emmc_key_init:527 emmc key lba_start:0x12020,lba_end:0x12220
[ 4.075205@3] emmc key: emmc_key_init:552 ok.
[ 4.075377@3] amlmmc_dtb_init: register dtb chardev
[ 4.075452@3] amlmmc_dtb_init: register dtb chardev OK
[ 4.075452@3] Exit aml_emmc_partition_ops OK.
[ 4.208759@0] arp_tables: (C) 2002 David S. Miller
[ 4.213233@3] mmcblk0boot1: unknown partition table
[ 4.218126@0] TCP: cubic registered
[ 4.221554@0] Initializing XFRM netlink socket
[ 4.226208@2] mmcblk0boot0: unknown partition table
[ 4.227046@3] NET: Registered protocol family 10
[ 4.228087@0] mip6: Mobile IPv6
[ 4.228107@0]�Z�_tables: (C) 2000-2006 Netfilter Core Team
[ 4.244410@3] clear_emmc_wayt_flagtunneling driver
[ 4.253698@2] NET> Registered protocol family 17
[ 4.256946@2] NET: Registered protocol family 15
[ 4.261486@2] Bridge firewalling registered
[ 4.265560@2] Bluetooth: RFCOMM TTY layer initialized
[ 4.270467@2] Bluetooth: RFCOMM socket layer initialized
[ 4.275765@2] Bluetooth: RFCOMM ver 1.11
[ 4.279600@2] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.285029@2] Bluetooth: BNEP filters: protocol multicast
[ 4.290378@2] Bluetooth: BNEP socket layer initialized
[ 4.295494@2] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 4.301499@2] Bluetooth: HIDP socket layer initialized
[ 4.306704@2] l2tp_core: L2TP core driver, V2.0
[ 4.311077@2] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 4.315996@2] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 4.321704@2] l2tp_netlink: L2TP netlink interface
[ 4.326485@2] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 4.332486@2] l2tp_debugfs: L2TP debugfs support
[ 4.337040@2] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 4.339996@3] sd: new high speed SDHC card at address aaaa
[ 4.340414@0] sd: clock 50000000, 4-bit-bus-width
[ 4.340414@0]
[ 4.340415@0] mmcblk1: sd:aaaa SL08G 7.40 GiB
[ 4.341578@3] mmcblk1: p1
[ 4.362568@2] NET: Registered protocol family 35
[ 4.367126@2] Key type dns_resolver registered
[ 4.373111@2] Registering SWP/SWPB emulation handler
[ 4.377114@2] regulator-dummy: disabling
[ 4.380678@2] aml_vrtc rtc.32: setting system clock to 2015-01-01 00:00:08 UTC (1420070408)
[ 4.390704@2] gxbb_pm: enter meson_pm_probe!
[ 4.392783@2] gxbb_pm: meson_pm_probe done
[ 4.397756@0] cpucore_cooling_register, max_cpu_core_num:4
[ 4.402432@0] cpucore_cooling_register, max_cpu_core_num:4
[ 4.423093@0] aml_istbt_dev_ready NULL
[ 4.423149[ 4.427938@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 4.431362@0] Freeing unused kernel memory: 1260K (ffffffc001eaa000 - ffffffc001fe5000)
[ 4.454659@1] init: init started!
[ 4.456194@1] init: init second stage started!
[ 4.457170@1] init: waitpid failed: No child processes
[ 4.462896@1] init: (Loading properties from /default.prop took 0.00s.)
[ 4.468831@1] init: /init.rc: 7: invalid command 'setcon'
[ 4.473816@1] init: /init.rc: 61: invalid command 'load_all_props'
[ 4.480051@1] init: (Parsing /init.recovery.amlogic.rc took 0.00s.)
[ 4.486118@1] init: (Parsing /init.rc took 0.02s.)
[ 4.490892@1] init: Starting service 'ueventd'...
[ 4.503120@0] ueventd: ueventd started!
[ 4.762817@3] ueventd: Coldboot took 0.26s.
[ 5.203621@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.203671@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 5.212243@1] xhci-hcd xhci-hcd.0.auto: irq 62, io mem 0xc9000000
[ 5.218127@1] hub 1-0:1.0: USB hub found
[ 5.221344@1] hub 1-0:1.0: 3 ports detected
[ 5.225700@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.231074@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 5.239475@1] hub 2-0:1.0: USB hub found
[ 5.242739@2] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 5.250607@2] init: Waiting for /dev/.coldboot_done...
[ 5.25 5.261399@2] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 5.275505@2] file system registered
[ 5.275784@2] init: write_file: Unable to write to '/sys/class/android_usb/android0/enable': No such device
[ 5.283220@2] init: write_file: Unable to open '/sys/class/android_usb/android0/f_ffs/aliases': No such file or directory
[ 5.294050@2] android_usb: Cannot enable 'adb' (-22)init: Starting service 'healthd'...
[ 5.302189@2] init: Starting service 'recovery'...
[ 5.306071@3] healthd: No charger supplies found
[ 5.306081@3] healthd: No battery devices found
[ 5.316008@2]` 5.322741@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 5.333176@0] systemcontrol: /etc/mesondisplay.cfg:12: Expected keyword, got '/etc/mesondisplay.cfg:12'.
[ 5.337608@2] vout_serve: vmode set to 1080p60hz
[ 5.341559@2] vout_serve: don't set the same mode as current
[ 5.349445@2] remote: cur_mode = 0
[ 5.350530@2] remote: set_remote_mode[74]
[ 5.354787@0] fb: osd[0] enable: 0 (recovery)
[ 5.357734@3] remote: cur_mode = 0
[ 5.357739@3] remote: set_remote_mode[74]
[ 5.377807@3] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: discard
# [ 5.405579@0] fb: osd[0] enable: 1 (recovery)
[ 5.422363@0] vout_serve: osd0=> x:0,y:0,w:1920,h:1080
[ 5.422363@0] osd1=> x:0,y:0,w:18,h:18
[ 5.429736@0] fb: current vmode=1080p60hz
[ 5.433859@0] fb: osd[1] set scale, h_scale: ENABLE, v_scale: ENABLE
[ 5.440025@0] fb: osd[1].scaledata: 1920 1920 1080 1080
[ 5.445159@0] fb: osd[1].pandata: 0 0 0 0
[ 5.455588@2] fb: osd[0] enable: 0 (recovery)
[ 5.472367@5] fb: osd[0] enable: 1 (recovery)
[ 5.544537@6] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 5.719285@6] hub 1-1:1.0: USB hub found
[ 5.719391@6] hub 1-1:1.0: 3 ports detected
[ 5.994555@4] usb 1-1.2: new low-speed USB device number 3 using xhci-hcd
[ 6.101413@6] usb 1-1.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.104837@6] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.214554@4] usb 1-1.3: new low-speed USB device number 4 using xhci-hcd
[ 6.319485@4] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.330676@7] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0003/input/input3
[ 6.338783@4] hid-generic 0003:046D:C05A.0003: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 6.392805@5] fb: use ion buffer for fb memory
[ 6.393535@5] meson-fb meson-fb.16: create ion_client ffffffc0653c7a80, handle=ffffffc0628656c0
[ 6.400287@5] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 6.408966@5] fb: Frame buffer memory assigned at
[ 6.413442@5] fb: 0, phy: 0x0000000079300000, vir:0xffffff8001d75000, size=24900K
[ 6.413442@5]
[ 6.422765@5] fb: ---------------clear fb0 memory ffffff8001d75000
[ 6.438282@2] fb: osd[0] canvas.idx =0x40
[ 6.438308@2] fb: osd[0] canvas.addr=0x79300000
[ 6.441142@2] fb: osd[0] canvas.width=7680
[ 6.445205@2] fb: osd[0] canvas.height=3240
[ 6.449335@2] fb: osd[0] frame.width=1920
[ 6.453303@2] fb: osd[0] frame.height=1080
[ 6.507987@0] fb: osd[0] canvas.idx =0x40
[ 6.507989@0] fb: osd[0] canvas.addr=0x79300000
[ 6.507991@0] fb: osd[0] canvas.width=7680
[ 6.507993@0] fb: osd[0] canvas.height=2160
[ 6.507994@0] fb: osd[0] frame.width=1920
[ 6.507995@0] fb: osd[0] frame.height=1080
[ 6.541325@0] fb: osd[0] enable: 0 (recovery)
[ 6.555502@0] fb: osd[0] enable: 1 (recovery)
[ 6.748178@0] EXT4-fs (mmcblk0p14): 2 orphan inodes deleted
[ 6.748212@0] EXT4-fs (mmcblk0p14): recovery complete
[ 6.767082@0] EXT4-fs (mmcblk0p14): mounted filesystem with ordered data mode. Opts: discard
[ 11.429467@6] random: nonblocking pool is initialized
[ 119.508360@0] EXT4-fs (mmcblk0p14): mounted filesystem with ordered data mode. Opts: discard
[ 119.906032@0] SysRq : Emergency Remount R/O
[ 119.912202@4] EXT4-fs (mmcblk0p14): re-mounted. Opts: (null)
[ 119.912598@4] Emergency Remount complete
[ 120.006793@4] avmute set to 2
[ 121.315992@3] aml_snd_card: no audio pin_ctrl to shutdown
[ 121.316088@3] sysled: module shutdown ok
[ 121.319699@0] reboot: Restarting system(init) with command ''
INFO: PSCI Affinity Map:
INFO: AffInst: Level 1, MPID 0x0, State ON
INFO: AffInst: Level 1, MPID 0x100, State ON
INFO: AffInst: Level 0, MPID 0x0, State ON
INFO: AffInst: Level 0, MPID 0x1, State ON
INFO: AffInst: Level 0, MPID 0x2, State ON
INFO: AffInst: Level 0, MPID 0x3, State ON
INFO: AffInst: Level 0, MPID 0x100, State ON
INFO: AffInst: Level 0, MPID 0x101, State ON
INFO: AffInst: Level 0, MPID 0x102, State ON
INFO: AffInst: Level 0, MPID 0x103, State ON
bl31 reboot reason: 0xd
bl31 reboot reason: 0x1
system cmd 1.
GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 194400
BL2 Built : 19:58:22, Aug 31 2016.
gxl g54c8aee - xiaobo.gu@droid05
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00015400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a9a00
NOTICE: BL3-1: v1.0(debug):2e39a99
NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
aml log : bl31 normal boot !
wdt: reset registers!
[Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
OPS=0x82
fc c2 9 21 fb ca c 14 7e b4 40 63 [0.442206 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gd267f87 (Jan 19 2017 - 16:49:10)
DRAM: 2 GiB
Relocation Offset is: 76ec9000
register usb cfg[0][1] = 0000000077f5f5d8
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073ec96b0
aml_priv->desc_buf = 0x0000000073ecb9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ece270,dt_addr=0000000073ed9270
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000080000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 80000000 1
13: data d7c00000 2c5400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=normal
## defenv_reserve
Saving Environment to aml-storage...
mmc env offset: 0x27400000
Writing to MMC(1)... done
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 4 vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
rx version is 1.4 or below div=10
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[CANVAS]canvas init
[CANVAS]addr=0x3d851000 width=5760, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
get_cpu_id flag_12bit=1
SARADC open channel(0).
SARADC channel(0) is 0x3c9, Out of range(0x0~0x50)!
saradc - saradc sub-system
Usage:
saradc saradc open <channel> - open a SARADC channel
saradc close - close the SARADC
saradc getval - get the value in current channel
saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
get_cpu_id flag_12bit=1
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =73f4e440
copy done
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x02106540
Loading Ramdisk to 73dd7000, end 73eb6f66 ... OK
Loading Device Tree to 000000001fff2000, end 000000001ffff1ca ... OK
signature:
fdt_instaboot: no instaboot image
Starting kernel ...
uboot time: 2073893 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-g6bba886 (lhh@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Thu Jan 19 17:08:41 CST 2017
[ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000@0] no prop version_code
[ 0.000000@0] bootconsole [earlycon0] enabled
[ 0.000000@0] fdt Reserved memory table:
[ 0.000000@0] linux,di: 0x000000007d300000 - 0x000000007f100000 (30 MiB)
[ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007d300000, size 30 MiB
[ 0.000000@0] linux,ion-dev: 0x0000000079300000 - 0x000000007d300000 (64 MiB)
[ 0.000000@0] linux,ppmgr: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] linux,codec_mm_cma: 0x0000000067c00000 - 0x0000000073c00000 (192 MiB)
[ 0.000000@0] linux,picdec: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] Reserved memory: incorrect alignment of CMA region
[ 0.000000@0] linux,codec_mm_reserved: 0x0000000075200000 - 0x0000000079300000 (65 MiB)
[ 0.000000@0] fdt Reserved memory total: 354 MiB
[ 0.000000@0] cma: Reserved 8 MiB at 74800000
[ 0.000000@0] psci: probing function IDs from device-tree
[ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc07516e000 s19968 r8192 d20992 u49152
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 510280
[ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=disabled logo=osd1,loaded,0x3d800000,1080p60hz maxcpus=8 vout=1080p60hz,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 androidboot.firstboot=0 jtag=apao androidboot.hardware=amlogic mac=86:37:20:48:cb:3e androidboot.mac=86:37:20:48:cb:3e
[ 0.000000@0] logo: osd1
[ 0.000000@0] logo: loaded
[ 0.000000@0] logo: 0x3d800000
[ 0.000000@0] logo: 1080p60hz
[ 0.000000@0] vout_serve: 1080p60hz
[ 0.000000@0] vout_serve: enable: 1
[ 0.000000@0] logo: get hdmimode: 1080p60hz
[ 0.000000@0] logo: get cvbsmode: 576cvbs
[ 0.000000@0] tv_vout: cvbs performance line = 0
[ 0.000000@0] jtag: jtag select 2
[ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000@0] Memory: 1643716K/2077696K available (10612K kernel code, 1153K rwdata, 3884K rodata, 1263K init, 5869K bss, 433980K reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
[ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff80423cc800 ( 35 MB)
[ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc07f100000 ( 2033 MB)
[ 0.000000@0] .init : 0xffffffc001eaa000 - 0xffffffc001fe5e00 ( 1264 kB)
[ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001ea9334 ( 14501 kB)
[ 0.000000@0] .data : 0xffffffc001fe6000 - 0xffffffc002106540 ( 1154 kB)
[ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01ea8fff]
[ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000@0] arch_multi_cluster:1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000005@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[ 0.008244@0] meson_bc_timer: mclk->mux_reg =ffffff8000014990,mclk->reg =ffffff8000016994
[ 0.016818@0] Console: colour dummy device 80x25
[ 0.021096@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.031672@0] pid_max: default: 32768 minimum: 301
[ 0.036580@0] Security Framework initialized
[ 0.040786@0] SELinux: Initializing.
[ 0.044530@0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.051367@0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.061617@0] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
[ 0.065713@0] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
[ 0.072721@0] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
[ 0.079712@0] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
[ 0.090070@0] Initializing cgroup subsys debug
[ 0.091175@0] Initializing cgroup subsys freezer
[ 0.095843@0] ftrace: allocating 36489 entries in 143 pages
[ 0.149530@0] /cpus/cpu@0: Missing clock-frequency property
[ 0.149574@0] /cpus/cpu@1: Missing clock-frequency property
[ 0.155155@0] /cpus/cpu@2: Missing clock-frequency property
[ 0.160784@0] /cpus/cpu@3: Missing clock-frequency property
[ 0.166356@0] /cpus/cpu@100: Missing clock-frequency property
[ 0.172138@0] /cpus/cpu@101: Missing clock-frequency property
[ 0.177907@0] /cpus/cpu@102: Missing clock-frequency property
[ 0.183689@0] /cpus/cpu@103: Missing clock-frequency property
[ 0.189457@0] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 0.239803@0] Meson chip version = RevA (22:A - 82:0)
[ 0.258208@1] CPU1: Booted secondary processor
[ 0.278178@2] CPU2: Booted secondary processor
[ 0.298185@3] CPU3: Booted secondary processor
[ 0.318215@4] CPU4: Booted secondary processor
[ 0.338216@5] CPU5: Booted secondary processor
[ 0.358227@6] CPU6: Booted secondary processor
[ 0.378249@7] CPU7: Booted secondary processor
[ 0.378343@0] Brought up 8 CPUs
[ 0.407163@0] SMP: Total of 8 processors activated.
[ 0.420130@2] sched: registering cpufreq notifiers for scale-invariant loads
[ 0.421654@2] instabooting: 0
[ 0.433821@2] pinctrl core: initialized pinctrl subsystem
[ 0.434523@2] regulator-dummy: no parameters
[ 0.438789@2] NET: Registered protocol family 16
[ 0.444426@3] ramoops: using module parameters
[ 0.448200@2] console [pstore-1] enabled
[ 0.451003@2] pstore: Registered ramoops as persistent store backend
[ 0.457378@2] ramoops: attached 0x100000@0x7300000, ecc: 0/0
[ 0.464005@3] cpuidle: using governor menu
[ 0.467447@3] aml_vdac_init: module init
[ 0.471338@2] register canvas platform driver
[ 0.475614@2] register rdma platform driver
[ 0.481306@2] vdso: 2 pages (1 code, 1 data) at base ffffffc001ff0000
[ 0.486222@2] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.493555@2] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.500455@2] software IO TLB [mem 0x64800000-0x64c00000] (4MB) mapped at [ffffffc064800000-ffffffc064bfffff]
[ 0.509442@2] Serial: AMBA PL011 UART driver
[ 0.514317@3] aml_i2c version: 20140813
[ 0.517837@3] i2c-core: driver [pmu4] using legacy resume method
[ 0.523829@2] codec_mm:codec_mm_module_init
[ 0.528069@3] aml_watch_point_probe, in
[ 0.532144@2] gxbb_mpll_clk: register mpll_clk_out0 success done
[ 0.537726@2] gxbb_mpll_clk: register mpll_clk_out1 success done
[ 0.543743@2] gxbb_mpll_clk: register mpll_clk_out2 success done
[ 0.549991@2] clk_sys: register PLL sys_pll success done
[ 0.555124@2] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
[ 0.560486@2] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
[ 0.565616@2] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
[ 0.571134@2] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
[ 0.577077@2] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
[ 0.583045@2] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
[ 0.588890@2] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
[ 0.594757@2] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
[ 0.600614@2] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
[ 0.606512@2] gxl_clk: clock initialization complete
[ 0.611674@2] clkmsr: Gxl msr_clk_reg0=ffffff800003c75c,msr_clk_reg2=ffffff800003e764
[ 0.621967@2] aml_iomap: amlogic iomap probe done
[ 0.624717@2] pinmux-gxl c1109880.pinmux: Init pinux probe!
[ 0.630654@2] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
[ 0.636885@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.644395@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ 0.652623@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.660488@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
domain-0 init dvfs: 4
domain-1 init dvfs: 4
[ 0.680694@2] codec_mm has 2 memory regions
[ 0.680763@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.687368@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.695981@3] codec_mm has 2 memory regions
[ 0.700066@3] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.708119@3] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.718683@2] vpu: driver version: v02
[ 0.720378@2] vpu: load vpu_clk: 666667000Hz(7)
[ 0.724994@2] vpu: vpu_probe OK
[ 0.729807@2] tv_vout: tvout_probe
[ 0.731472@2] tv_vout: major number 254 for disp
[ 0.736100@2] vout_notify: vout_register_server
[ 0.740662@2] tv_vout: register tv module server ok
[ 0.745662@2] tv_vout: tvout_probe OK
[ 0.749892@2] canvas_probe reg=00000000c8838000,size=400
[ 0.754623@2] canvas maped reg_base =ffffff800009a000
[ 0.763913@2] rdma_probe
[ 1.078615@0] bio: create slab <bio-0> at 0
[ 1.079825@1] SCSI subsystem initialized
[ 1.081736@1] usbcore: registered new interface driver usbfs
[ 1.086981@0] usbcore: registered new interface driver hub
[ 1.092663@0] usbcore: registered new device driver usb
[ 1.098630@1] i2c-gpio i2c_gpio.38: using pins 172 (SDA) and 173 (SCL)
[ 1.104324@0] Linux video capture interface: v2.00
[ 1.109274@0] pps_core: LinuxPPS API ver. 1 registered
[ 1.114413@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 1.123677@0] PTP clock support registered
[ 1.128873@2] hdmitx: system: amhdmitx_init
[ 1.131840@2] hdmitx: system: Ver: 2014May6
[ 1.136215@2] hdmitx: system: amhdmitx_probe
[ 1.140643@1] hdmitx: system: not find match init-data
[ 1.145488@1] hdmitx: system: not find match pwr-ctl
[ 1.150519@1] hdmitx hpd irq = 89
[ 1.154301@1] hdmitx20: Mapped PHY: 0xc0800000
[ 1.158272@1] hdmitx20: Mapped PHY: 0xc1104400
[ 1.162754@1] hdmitx20: Mapped PHY: 0xc8100000
[ 1.167188@1] hdmitx20: Mapped PHY: 0xc8834000
[ 1.171649@1] hdmitx20: Mapped PHY: 0xc883a000
[ 1.176233@1] hdmitx20: Mapped PHY: 0xc883c000
[ 1.180578@1] hdmitx20: Mapped PHY: 0xd0100000
[ 1.185037@1] hdmitx20: Mapped PHY: 0xda83a000
[ 1.189512@1] hdmitx: alread display in uboot 0x10
[ 1.194330@1] avmute set to 1
[ 1.197704@1] vout_serve: vout_init_module
[ 1.201582@1] tv_vout: tv_set_current_vmode[759]fps_target_mode=16
[ 1.204392@0] hdmitx: system: irq 80000002
[ 1.211733@1] tv_vout: mode is 16,sync_duration_den=1,sync_duration_num=60
[ 1.218641@1] tv_vout: already display in uboot
[ 1.223194@1] vout_serve: vinfo mode is: 1080p60hz
[ 1.227998@1] vout_serve: init mode 1080p60hz
[ 1.232512@0] vout_serve: create vout attribute OK
[ 1.237187@0] vout_serve: meson_vout_probe OK
[ 1.241800@0] logo: logo_init
[ 1.244950@0] osd_rdma: osd_rdma_init: rdma_table p=0x74841000,op=0x74841000 , v=0xffffff800009e000
[ 1.253662@0] osd_rdma: osd rdma request irq as second interrput function!
[ 1.261067@0] Advanced Linux Sound Architecture Driver Initialized.
[ 1.267586@0] Bluetooth: Core ver 2.18
[ 1.270735@1] NET: Registered protocol family 31
[ 1.275276@1] Bluetooth: HCI device and connection manager initialized
[ 1.281821@1] Bluetooth: HCI socket layer initialized
[ 1.286898@1] Bluetooth: L2CAP socket layer initialized
[ 1.292166@1] Bluetooth: SCO socket layer initialized
[ 1.297704@0] cfg80211: Calling CRDA to update world regulatory domain
[ 1.303902@2] NetLabel: Initializing
[ 1.307378@2] NetLabel: domain hash size = 128
[ 1.311910@2] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.317134@2] NetLabel: unlabeled traffic allowed by default
[ 1.324840@3] Switched to clocksource arch_sys_counter
[ 1.374659@3] [amlatvdemod..]aml_atvdemod_init.
[ 1.374803@3] NET: Registered protocol family 2
[ 1.378774@3] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.385769@3] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 1.392682@3] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.399271@3] TCP: reno registered
[ 1.402595@3] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 1.408847@3] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 1.415924@3] NET: Registered protocol family 1
[ 1.420266@3] RPC: Registered named UNIX socket transport module.
[ 1.426144@3] RPC: Registered udp transport module.
[ 1.431024@3] RPC: Registered tcp transport module.
[ 1.435931@3] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.442794@3] aml_wifi wifi.33: [wifi_dev_probe] no power_on_pin2
[ 1.448710@3] aml_wifi wifi.33: [wifi_dev_probe] set pwm as 32k output
[ 1.455356@3] aml_wifi wifi.33: [wifi_dev_probe] dhd_static_buf setup
[ 1.461803@3] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem: WIFI MEM Allocated
[ 1.469383@3] aml_wifi wifi.33: [wifi_dev_probe] interrupt_pin=241
[ 1.475574@3] aml_wifi wifi.33: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
[ 1.483001@3] aml_wifi wifi.33: [wifi_dev_probe] power_on_pin=240
[ 1.489141@3] aml_wifi wifi.33: [wifi_dev_probe] clock_32k_pin=0
[ 1.495501@2] aml_wifi wifi.33: [wifi_setup_dt] wifi_setup_dt
[ 1.500975@2] aml_wifi wifi.33: [wifi_setup_dt] interrupt_pin(241)
[ 1.507173@2] aml_wifi wifi.33: [wifi_setup_dt] power_on_pin(240)
[ 1.513651@3] Unpacking initramfs...
[ 1.544962@1] hdmitx: plugin
[ 1.548216@3] Freeing initrd memory: 892K (ffffffc073dd7000 - ffffffc073eb6000)
[ 1.554795@3] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 1.556640@3] audit: initializing netlink subsys (disabled)
[ 1.562098@3] audit: type=2000 audit(1.450:1): initialized
[ 1.568522@0] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.581781@0] VFS: Disk quotas dquot_6.5.2
[ 1.582062@3] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.592291@0] NFS: Registering the id_resolver key type
[ 1.592361@0] Key type id_resolver registered
[ 1.596749@0] Key type id_legacy registered
[ 1.600846@0] NTFS driver 2.1.30 [Flags: R/O].
[ 1.605742@3] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.613318@0] fuse init (API version 7.22)
[ 1.617715@0] msgmni has been set to 3612
[ 1.622252@3] NET: Registered protocol family 38
[ 1.626151@3] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 1.632903@3] io scheduler noop registered
[ 1.637067@3] io scheduler deadline registered
[ 1.641720@0] io scheduler cfq registered (default)
[ 1.681763@1] hdmitx: edid: check sum valid
[ 1.681799@1] hdmitx: edid: check sum valid
[ 1.684584@1] hdmitx: edid: blk0 raw data
[ 1.688666@1] 00ffffffffffff001e6de37689bb02000b18010380502278eaca95a6554ea126
[ 1.688666@1] 0f50542108007140818081c0a9c0b300d1c0810001019d6770a0d0a022503020
[ 1.688666@1] 3a00204f3100001a000000fd00383d1e5a1e000a202020202020000000fc004c
[ 1.688666@1] 4720554c545241574944450a000000000000000000000000000000000000017c
[ 1.688666@1]
[ 1.688666@1]
[ 1.696749@0] meson-rng c8834000.rng: hwrng registered
[ 1.700420@0] loop: module loaded
[ 1.701081@3] zram: Created 1 device(s) ...
[ 1.702135@3] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.702961@3] tun: Universal TUN/TAP device driver, 1.6
[ 1.702963@3] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 1.751986@1] hdmitx: edid: blk1 raw data
[ 1.756028@1] 020317f14410040301230907078301000065030c0010009f3d70a0d0a0155030
[ 1.756028@1] 203a00204f3100001a7e4800e0a0381f4040403a00204f31000018011d007251
[ 1.756028@1] d01e206e285500204f3100001e8c0ad08a20e02d10103e9600204f3100001800
[ 1.756028@1] 0000ff003431314b4b484e35393038310a0000000000000000000000000000ce
[ 1.756028@1]
[ 1.756028@1]
[ 1.788379@1] EDID Parser:
[ 1.791118@1] hdmitx: edid: find IEEEOUT
[ 1.795038@1]
[ 1.796670@1] hdmitx: edid: check sum valid
[ 1.800868@1] hdmitx: edid: check sum valid
[ 1.805078@1] hdmitx: update RX hdr info 0
[ 1.811202@1] hdmitx: ddc rd8b error 0x3a 0x00 0x00
[ 1.816128@1] [RX]-receive ksv list len:1,depth:1,cas:0,dev:0
[ 1.819865@1] hdmitx: video: get current mode: 1080p60hz
[ 1.825211@1] hdmitx: update rx hdr info 0
[ 1.829321@1] hdmitx: get ext_name (null)
[ 1.833335@1] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 16
[ 1.839300@3] libphy: stmmac: probed
[ 1.839305@3] eth0: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[ 1.839308@3] eth0: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07)
[ 1.839776@3] PPP generic driver version 2.4.2
[ 1.840002@3] PPP BSD Compression module registered
[ 1.840004@3] PPP Deflate Compression module registered
[ 1.840022@3] PPP MPPE Compression module registered
[ 1.840025@3] NET: Registered protocol family 24
[ 1.840177@2] usbcore: registered new interface driver asix
[ 1.840327@3] usbcore: registered new interface driver ax88179_178a
[ 1.840435@2] usbcore: registered new interface driver cdc_ether
[ 1.840535@3] usbcore: registered new interface driver net1080
[ 1.840631@2] usbcore: registered new interface driver cdc_subset
[ 1.840727@3] usbcore: registered new interface driver zaurus
[ 1.840853@2] usbcore: registered new interface driver cdc_ncm
[ 1.841174@2] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.841177@2] ehci-h20ahb: H20AHB-EHCI Host Controller driver
[ 1.841425@3] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.841795@3] usbcore: registered new interface driver cdc_acm
[ 1.841797@3] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.841913@2] usbcore: registered new interface driver usb-storage
[ 1.842139@2] usbcore: registered new interface driver usbserial
[ 1.842857@3] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff80000da000
[ 1.843079@2] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
[ 1.843105@2] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff80000ee080
[ 1.843744@2] mousedev: PS/2 mouse device common for all mice
[ 1.844313@3] usbcore: registered new interface driver xpad
[ 1.844518@3] i2c /dev entries driver
[ 1.844922@2] usbcore: registered new interface driver uvcvideo
[ 1.844924@2] USB Video Class driver (1.1.1)
[ 1.845825@2] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: [email protected]
[ 1.845922@2] Bluetooth: HCI UART driver ver 2.2
[ 1.845925@2] Bluetooth: HCI H4 protocol initialized
[ 1.846279@2] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
[ 1.848500@0] cpu cpu4: bL_cpufreq_init: CPU 4 initialized
[ 1.848660@0] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
[ 1.848957@3] CPUidle arm64: cpuidle init start!!
[ 1.849757@3] @@@@@@@@@@_____2______in dia_init()
[ 1.849986@3] ATVR driver - init called!
[ 1.849987@3] usbcore: registered new interface driver usbhid
[ 1.849988@3] usbhid: USB HID core driver
[ 1.850326@3] ashmem: initialized
[ 1.850481@0] logger: created 256K log 'log_main'
[ 1.850606@3] logger: created 256K log 'log_events'
[ 1.850728@0] logger: created 256K log 'log_radio'
[ 1.850892@3] logger: created 256K log 'log_system'
[ 1.852012@0] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff80000fc4c0
[ 1.852035@0] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
[ 2.120266@1] hdmtix: set audio
[ 2.123404@1] hdmitx tx_aud_src = 0
[ 2.126925@1] hdmitx: fs = 0, cd = 4, tmds_clk = 148500
[ 2.132145@1] hdmitx aud_n_para = 6144
[ 2.135928@1] hdmitx set channel status
[ 2.145274@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
[ 2.147902@0] console [ttyS0] enabled
[ 2.147902@0] console [ttyS0] enabled
[ 2.155172@0] bootconsole [earlycon0] disabled
[ 2.155172@0] bootconsole [earlycon0] disabled
[ 2.164347@0] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff80000fe4c0
[ 2.170987@0] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
[ 2.180753@0] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff]
[ 2.190362@0] meson-gpu-clkgen: probe of c883c000.gpu_clk failed with error -16
[ 2.197703@0] hdmitx: system: hdmitx_hdcp_init
[ 2.202003@3] ESM HLD: Initializing...
[ 2.205530@3] ESM HLD: Registering device range 'esm'...
[ 2.210777@3] ESM HLD: Device range 'esm' has been registered.
[ 2.216567@3] ESM HLD: Creating class /sys/class/elliptic...
[ 2.222266@0] ESM HLD: The class /sys/class/elliptic has been created.
[ 2.228636@0] ESM HLD: Creating device 'esm'...
[ 2.233252@0] ESM HLD: Device 'esm' has been created.
[ 2.238190@0] ESM HLD: Done initializing the HLD driver.
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[ 2.259365@3] aml_vrtc rtc.32: rtc core: registered aml_vrtc as rtc0
[ 2.260762@3] secmon has 1 memory regions
[ 2.264077@3] secmon: share in base: 0xffffff800011a000, share out base: 0xffffff800011c000
[ 2.272375@3] secmon secmon.4: assigned reserved memory node linux,secmon ok
[ 2.279312@3] secmon: probe done
[ 2.282845@0] storage: storage in base: 0xffffff8001800000
[ 2.287967@0] storage: storage out base: 0xffffff8001880000
[ 2.293449@0] storage: storage block base: 0xffffff8001900000
[ 2.299154@0] storage: probe done!
[ 2.303050@3] aml_sd_emmc_probe: line 3578
[ 2.306574@3] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
[ 2.316401@3] aml_sd_emmc_reg_init 1146
[ 2.319809@3] get property: ocr_avail, value:0x00200080
[ 2.326253@3] get property: f_min, value:300000
[ 2.332349@3] get property: f_max, value:100000000
[ 2.338738@3] get property: max_req_size, value:0x00020000
[ 2.345217@3] get property: pinname, str:emmc
[ 2.350981@3] get property: card_type, value:1
[ 2.356693@3] get property: gpio_dat3, str:
[ 2.362106@3] get property: hw_reset, str:
[ 2.367576@3] emmc:pdata->caps = c0000d47
[ 2.371511@3] emmc:pdata->caps2 = 18060
[ 2.375317@3] storage 1, boot 1
[ 2.378406@3] get_storage_dev return 1
[ 2.414850@0] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.415068@0] aml_sd_emmc_probe: line 3578
[ 2.419487@0] aml_sd_emmc_reg_init 1146
[ 2.423014@0] get property: ocr_avail, value:0x00200080
[ 2.429443@0] get property: f_min, value:400000
[ 2.435583@0] get property: f_max, value:100000000
[ 2.441861@0] get property: max_req_size, value:0x00020000
[ 2.448335@0] get property: irq_in, value:3
[ 2.454038@0] get property: irq_out, value:5
[ 2.459801@0] get property: gpio_cd, str:
[ 2.465155@0] get property: pinname, str:sd
[ 2.470772@0] get property: jtag_pin, str:
[ 2.476269@0] get property: card_type, value:5
[ 2.481883@0] get property: gpio_dat3, str:
[ 2.487349@0] sd:pdata->caps = 7
[ 2.490505@0] sd:pdata->caps2 = 0
[ 2.525014@3] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.525046@4] [aml_is_card_insert] card IN
[ 2.529284@3] aml_sd_emmc_probe: line 3578
[ 2.533648@3] aml_sd_emmc_reg_init 1146
[ 2.537170@3] get property: ocr_avail, value:0x00200080
[ 2.543575@3] get property: f_min, value:400000
[ 2.549705@3] get property: f_max, value:200000000
[ 2.556088@3] get property: max_req_size, value:0x00020000
[ 2.562554@3] get property: pinname, str:sdio
[ 2.568335@3] get property: card_type, value:3
[ 2.574059@3] sdio:pdata->caps = 7810f
[ 2.577735@3] sdio:pdata->caps2 = 0
[ 2.611612@2] emmc: BKOPS_EN bit is not set
[ 2.614850@2] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.616333@0] ion_dev has 1 memory regions
[ 2.621841@2] gmmc: trying cali 0-th time(s)
[ 2.626384@4] normal card in
[ 2.634456@2] emmc: delay[0]= 4600 padding= 2, bidx=4
[ 2.634479@2] emmc: delay[1]= 4600 padding= 2, bidx=4
[ 2.636579@1] fb: osd_init_module
[ 2.636704@1] fb: viu vsync irq: 35
[ 2.636710@1] fb: failed to init reserved memory
[ 2.636722@1] fb: osd_probe vinfo:ffffffc002086d98
[ 2.636726@1] fb: init fbdev bpp is:32
[ 2.658632@2] emmc: delay[2]= 4400 padding= 3, bidx=4
[ 2.663623@2] emmc: delay[3]= 4800 padding= 1, bidx=4
[ 2.663629@2] emmc: delay[4]= 4800 padding= 1, bidx=4
[ 2.663631@2] emmc: delay[5]= 4800 padding= 1, bidx=4
[ 2.663633@2] emmc: delay[6]= 4600 padding= 2, bidx=4
[ 2.663635@2] emmc: delay[7]= 4800 padding= 1, bidx=4
[ 2.663637@2] emmc: calibration result @ 0: max(4800), min(4400)
[ 2.663640@2] emmc: line_delay =0x1000211, max_cal_result =4800
[ 2.663641@2] emmc: base_index_max 4, base_index_min 4
[ 2.663647@2] emmc: clk 100000000 SDR mode tuning start
[ 2.664390@2] emmc: rx_tuning_result[0] = 10
[ 2.664922@2] emmc: rx_tuning_result[1] = 10
[ 2.665452@2] emmc: rx_tuning_result[2] = 10
[ 2.665982@2] emmc: rx_tuning_result[3] = 10
[ 2.666511@2] emmc: rx_tuning_result[4] = 10
[ 2.667040@2] emmc: rx_tuning_result[5] = 10
[ 2.667574@2] emmc: rx_tuning_result[6] = 10
[ 2.668105@2] emmc: rx_tuning_result[7] = 10
[ 2.668635@2] emmc: rx_tuning_result[8] = 10
[ 2.668690@2] emmc: best_win_start =0, best_win_size =9
[ 2.668693@2] emmc: sd_emmc_regs->gclock=0x100024a,sd_emmc_regs->gadjust=0x42000
[ 2.668697@2] emmc: gclock =0x100024a, gdelay=0x1000211, gadjust=0x42000
[ 2.669025@2] emmc: new HS200 MMC card at address 0001
[ 2.669443@0] emmc: clock 100000000, 8-bit-bus-width
[ 2.669443@0]
[ 2.669443@0] mmcblk0: emmc:0001 NCard 14.4 GiB
[ 2.669566@0] mmcblk0boot0: emmc:0001 NCard partition 1 4.00 MiB
[ 2.669683@0] mmcblk0boot1: emmc:0001 NCard partition 2 4.00 MiB
[ 2.669800@0] mmcblk0rpmb: emmc:0001 NCard partition 3 4.00 MiB
[ 2.670389@2] mmcblk0: unknown partition table
[ 2.671118@0] [mmc_read_partition_tbl] mmc read partition OK!
[ 2.671119@0] add_emmc_partition
[ 2.671287@2] [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
[ 2.671423@0] [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
[ 2.671554@2] [mmcblk0p03] cache offset 0x000006c00000, size 0x000020000000
[ 2.671671@0] [mmcblk0p04] env offset 0x000027400000, size 0x000000800000
[ 2.671790@2] [mmcblk0p05] logo offset 0x000028400000, size 0x000002000000
[ 2.671912@0] [mmcblk0p06] recovery offset 0x00002ac00000, size 0x000002000000
[ 2.672031@2] [mmcblk0p07] rsv offset 0x00002d400000, size 0x000000800000
[ 2.672147@0] [mmcblk0p08] tee offset 0x00002e400000, size 0x000000800000
[ 2.672276@2] [mmcblk0p09] crypt offset 0x00002f400000, size 0x000002000000
[ 2.672401@0] [mmcblk0p10] misc offset 0x000031c00000, size 0x000002000000
[ 2.672529@2] [mmcblk0p11] instaboot offset 0x000034400000, size 0x000020000000
[ 2.672641@0] [mmcblk0p12] boot offset 0x000054c00000, size 0x000002000000
[ 2.672762@2] [mmcblk0p13] system offset 0x000057400000, size 0x000080000000
[ 2.672882@0] [mmcblk0p14] data offset 0x0000d7c00000, size 0x0002c5400000
[ 2.672914@0] card key: card_blk_probe.
[ 2.672918@0] emmc_key_init:527 emmc key lba_start:0x12020,lba_end:0x12220
[ 2.672921@0] emmc key: emmc_key_init:552 ok.
[ 2.673096@0] amlmmc_dtb_init: register dtb chardev
[ 2.673178@2] amlmmc_dtb_init: register dtb chardev OK
[ 2.673178@2] Exit aml_emmc_partition_ops OK.
[ 2.674192@0] mmcblk0boot1: unknown partition table
[ 2.674988@0] mmcblk0boot0: unknown partition table
[ 2.675272@2] clear_emmc_wait_flag
[ 2.760290@2] sd: new high speed SDHC card at address aaaa
[ 2.760727@0] sd: clock 50000000, 4-bit-bus-width
[ 2.760727@0]
[ 2.760727@0] mmcblk1: sd:aaaa SL08G 7.40 GiB
[ 2.761881@2] mmcblk1: p1
[ 3.000783@0] fb: osd probe OK
[ 3.001064@0] ge2d: ge2d_init_module
[ 3.001751@0] ge2d: ge2d_dev major:242
[ 3.005860@3] ge2d: ge2d clock is 400 MHZ
[ 3.009423@3] ge2d: ge2d: pdev=ffffffc06560b600, irq=182, rstc=0xffffffc063885340, clk=ffffffc06565c800
[ 3.018801@3] ge2d: mapped phy: 0xd0160000
[ 3.022791@3] ge2d: ge2d start monitor
[ 3.026580@2] ge2d: ge2d workqueue monitor start
[ 3.026805@1] sysled: module init
[ 3.026929@1] sysled: led_gpio = 154
[ 3.026930@1] sysled: active_low = 0
[ 3.027086@3] sysled: module probed ok
[ 3.027483@3] pwmled: module init
[ 3.027571@3] codec:Amlogic A/V streaming port init
[ 3.028952@1] codec:get gate demux control ok ffffffc0644cc1c0
[ 3.028957@1] codec:get gate parser_top control ok ffffffc0644cccc0
[ 3.028963@1] codec:get gate vpu_intr control ok ffffffc06459ef00
[ 3.028969@1] codec:get gate vdec control ok ffffffc06459ea80
[ 3.029585@1] codec:[tsync_pcr_init]init success.
[ 3.029587@1] codec:amvideocap_init_module
[ 3.029719@1] codec:amvideocap_probe,amvideocap
[ 3.029721@1] codec:use cma buf.
[ 3.029723@1] codec:amvideocap_dev_register
[ 3.031578@3] amvenc_avc_probe -- reserved memory config fail.
[ 3.031582@3] amvenc_avc - cma memory pool size: 40 MB
[ 3.031600@3] encode_wq_init.
[ 3.031605@3] encode start monitor.
[ 3.031655@0] encode workqueue monitor start.
[ 3.032075@3] jpegenc module init
[ 3.032381@1] codec:picdec_driver_probe called.
[ 3.032384@1] picdec has 1 memory regions
[ 3.032406@1] codec:picdec_driver_probe done.
[ 3.033331@1] codec:create_ge2d_work_queue video task ok
[ 3.033702@3] codec:used fix clk for vdec clk source!
[ 3.033707@3] codec:register clk_set_setting cpu[34]
[ 3.034057@3] vpu_init
[ 3.034232@3] vpu_probe
[ 3.034236@3] HevcEnc reserved memory config fail.
[ 3.034239@3] HevcEnc - cma memory pool size: 64 MB
[ 3.034242@3] HevcEnc - wave420l_irq: 219
[ 3.034283@3] vpu base address get from platform driver physical base addr=0xc8810000, virtual base=0xffffff8000258000
[ 3.034574@3] success to probe vpu device with video memory from cma
[ 3.034725@1] DI: di_module_init ok.
[ 3.034729@1] DI: di_module_init: major 235
[ 3.034970@3] DI: di_probe
[ 3.035109@1] deinterlace has 1 memory regions
[ 3.035141@1] deinterlace deinterlace.26: assigned reserved memory node linux,di ok
[ 3.035161@1] di_irq:78,timerc_irq:38
[ 3.211584@2] rdma_register, rdma_table_addr ffffff800017d000 rdma_table_addr_phy 74848000 reg_buf ffffffc063f02000
[ 3.221781@2] rdma_register success, handle 1 table_size 8192
[ 3.227465@2] DI: di_probe allocate rdma channel 1.
[ 3.232292@2] DI: DI hw version 2.
[ 3.235668@2] 0x000000db:Y=db,U=0,V=0
[ 3.239276@2] 0x000000dc:Y=dc,U=0,V=0
[ 3.242898@2] 0x000000dd:Y=dd,U=0,V=0
[ 3.246528@2] 0x000000de:Y=de,U=0,V=0
[ 3.250143@2] 0x000000df:Y=df,U=0,V=0
[ 3.253765@2] 0x000000e0:Y=e0,U=0,V=0
[ 3.257393@2] 0x000000e1:Y=e1,U=0,V=0
[ 3.261011@2] 0x000000e2:Y=e2,U=0,V=0
[ 3.264633@2] 0x000000e3:Y=e3,U=0,V=0
[ 3.268261@2] 0x000000f0:Y=f0,U=0,V=0
[ 3.271881@2] 0x000000f1:Y=f1,U=0,V=0
[ 3.275506@2] 0x000000f2:Y=f2,U=0,V=0
[ 3.279123@2] 0x000000f3:Y=f3,U=0,V=0
[ 3.282745@2] 0x000000f4:Y=f4,U=0,V=0
[ 3.286373@2] 0x000000f5:Y=f5,U=0,V=0
[ 3.289991@2] 0x000000f6:Y=f6,U=0,V=0
[ 3.293615@2] 0x000000f7:Y=f7,U=0,V=0
[ 3.297240@2] 0x000000f8:Y=f8,U=0,V=0
[ 3.300858@2] 0x000000f9:Y=f9,U=0,V=0
[ 3.304481@2] 0x000000fa:Y=fa,U=0,V=0
[ 3.308108@2] 0x000000fb:Y=fb,U=0,V=0
[ 3.311726@2] 0x000000fc:Y=fc,U=0,V=0
[ 3.315495@2] DI: di_probe here.
[ 3.318941@2] efusekeynum: 4
[ 3.321394@2] efusekeyname: mac offset: 0 size: 6
[ 3.327811@2] efusekeyname: mac_bt offset: 6 size: 6
[ 3.334155@2] efusekeyname: mac_wifi offset: 12 size: 6
[ 3.340556@2] efusekeyname: usid offset: 18 size: 16
[ 3.347225@1] efuse efuse.10: probe OK!
[ 3.351129@2] key unify config unifykey-num is 14
[ 3.355449@2] key unify fact unifykey-num is 14
[ 3.359856@2] aml_unifykeys_probe:1273=============unifykey_devno:e900000
[ 3.366876@1] 6unifykey: device unifykeys created ok
[ 3.371730@2] 6aml_unifykeys_init done!
[ 3.375485@2] PPMGRDRV: warn: ppmgr module init func called
[ 3.381131@2] PPMGRDRV: err: ppmgr_driver_probe called
[ 3.386103@2] ppmgr has 1 memory regions
[ 3.389987@2] PPMGRDRV: info: ppmgr_dev major:232
[ 3.394920@1] PPMGRDRV: info: ppmgr_probe done
[ 3.399488@2] amlogic rfkill init
[ 3.402413@2] enter bt_probe of_node
[ 3.405889@2] not get gpio_en
[ 3.408758@2] power on valid level is high
[ 3.412982@2] Bluetooth: BlueSleep Mode Driver Ver 1.2
[ 3.418501@2] ionvideo-000: V4L2 device registered as video13
[ 3.423594@2] ionvid: info: Video Technology Magazine Ion Video
[ 3.429508@2] ionvid: info: Capture Board ver 1.0 successfully loaded
[ 3.435869@2] audio_dsp: [dsp]register dsp to char divece(257)
[ 3.442342@2] amaudio: amaudio: driver amaudio succuess!
[ 3.447299@2] amlvid:err: amlvideo_init called
[ 3.451108@1] amlvid:err: amlvideo_create_instance called
[ 3.456674@1] amlvid:err: v4l2_dev.name=:amlvideo-000
[ 3.461822@2] amlvideo-000: V4L2 device registered as video10
[ 3.467785@1] vdin_drv_init: major 231
[ 3.471386@2] vdin_drv_init: vdin driver init done
[ 3.475827@2] tvafe_drv_init: major 230
[ 3.479936@2] tvafe: tvafe_init.
[ 3.483076@1] [RX]-hdmirx: hdmirx_init.
[ 3.486568@1] ESM HLD: Initializing...
[ 3.490264@1] ESM HLD: Registering device range 'esm_rx'...
[ 3.495797@1] ESM HLD: Device range 'esm_rx' has been registered.
[ 3.501821@1] ESM HLD: Creating class /sys/class/elliptic_rx...
[ 3.507827@2] ESM HLD: The class /sys/class/elliptic_rx has been created.
[ 3.514414@2] ESM HLD: Creating device 'esm_rx'...
[ 3.519335@2] ESM HLD: Device 'esm_rx' has been created.
[ 3.524419@2] ESM HLD: Done initializing the HLD driver.
[ 3.529755@2] [viuin..]viuin_init_module viuin module init
[ 3.535632@2] [viuin..]viuin_probe probe ok.
[ 3.539423@2] module init
[ 3.542067@2]
[ 3.542067@2] VECM probe start
[ 3.547018@2] aml_vecm_probe: ok
[ 3.550536@2] saradc c1108680.saradc: initialized by BL30
[ 3.555267@2] saradc c1108680.saradc: calibration start:
[ 3.560514@2] saradc c1108680.saradc: nominal=0, value=5
[ 3.565794@2] saradc c1108680.saradc: nominal=256, value=251
[ 3.571380@2] saradc c1108680.saradc: nominal=512, value=499
[ 3.577025@2] saradc c1108680.saradc: nominal=768, value=747
[ 3.582593@2] saradc c1108680.saradc: nominal=1023, value=996
[ 3.588262@2] saradc c1108680.saradc: calibration end: coef=4228
[ 3.594454@2] remote: Driver init
[ 3.597615@2] remote: platform_data g_remote_ao_offset=580
[ 3.602907@2] remote: platform_data irq =228
[ 3.607215@2] remote: set drvdata completed
[ 3.611368@2] remote: device_create_file completed
[ 3.616600@2] input: aml_keypad as /devices/meson-remote.12/input/input0
[ 3.623213@2] remote: input_register_device completed
[ 3.628133@2] remote: set_remote_mode[74]
[ 3.632082@2] remote: remote config major:227
[ 3.636718@2] remote: physical address:0x63e8e000
[ 3.641740@2] gpio-key gpio_keypad.48: gpio_key: 0 name(power) pin()
[ 3.647453@2] gpio-key gpio_keypad.48: amlogic_gpio_name_map_num pin 0!::
[ 3.654153@2] gpio-key gpio_keypad.48: gpio_key: 0 power(147)
[ 3.659908@2] gpio-key gpio_keypad.48: start setup_timer
[ 3.665114@2] gpio-key gpio_keypad.48: power key(116) registed.
[ 3.671215@1] input: gpio_keypad as /devices/gpio_keypad.48/input/input1
[ 3.677817@2] gpio-key gpio_keypad.48: gpio keypad register input device completed.
[ 3.685237@2] input input1: gpio keypad major:226
[ 3.691154@2] Sensor: lsm303d_init
[ 3.693437@2] Sensor: stk8313_init
[ 3.696714@1] Sensor: stk831x_init
[ 3.700023@2] Sensor: mxc622x_acc_init
[ 3.703735@2] Sensor: mxc6255xc_acc_init
[ 3.707754@2] Sensor: l3gd20_gyr_init
[ 3.712139@2] aml dvb init
[ 3.714238@2] Amlogic Demod DVB-T/C DebugIF Init
[ 3.718666@1] Amlogic Demod DVB-T/C DebugIF Init ok----------------
[ 3.725592@1] jtag: module init
[ 3.727900@2] jtag: pinctrl setup apao
[ 3.731419@2] jtag: set state 2
efuse_pw_en: 0x3
WARNING! efuse bits is disabled
Enable A53 JTAG cluster 0 to AO
[ 3.747572@0] jtag: module probed ok
[ 3.747974@2] cpuinfo: probe done
[ 3.749170@2] defendkey c8834500.defendkey: defendkey_devno:de00000
[ 3.755435@3] defendkey c8834500.defendkey: defendkey: device defendkey created ok
[ 3.762752@2] defendkey: driver init
[ 3.766129@2] input input1: key 116 up
[ 3.770576@2] input: cec_input as /devices/virtual/input/input2
[ 3.776021@2] cectx aocec: no hdmirx reg resource
[ 3.780325@2] cectx aocec: no hhi reg resource
[ 3.784817@2] cectx aocec: can't find hdmirx
[ 3.790000@2] cec: wake up flag:0
[ 3.793134@3] aml_aes_dma c883e000.aml_aes: Aml AES_dma
[ 3.798109@2] aml_tdes_dma c883e000.aml_tdes: Aml TDES_dma
[ 3.803519@2] aml_sha_dma c883e000.aml_sha: Aml SHA1/SHA224/SHA256 dma
[ 3.809915@2] usbcore: registered new interface driver snd-usb-audio
[ 3.817063@3] aml_codec_T9015 c8832000.t9015: aml_T9015_audio_codec_probe
[ 3.824412@3] aml_pcm_dai: pcm mode detection =1
[ 3.827427@3] aml_spdif_dai: enterd aml_spdif_play,set_clock:-1,sample_rate=4
[ 3.833992@3] aml_spdif_dai: set normal 512 fs /4 fs
[ 3.838965@3] aml_audio_hw: IEC958 16bit
[ 3.842770@3] hdmitx: audio: aout notify rate 48000
[ 3.847604@3] hdmitx: audio: aout notify size 16
[ 3.852169@3] hdmitx: audio: aout notify format CT_PCM
[ 3.857321@3] hdmtix: set audio
[ 3.860373@3] hdmitx tx_aud_src = 0
[ 3.863837@3] hdmitx: fs = 3, cd = 4, tmds_clk = 148500
[ 3.868994@3] hdmitx aud_n_para = 6144
[ 3.872713@3] hdmitx set channel status
[ 3.876568@3] hdmitx: audio: Audio Type: PCM
[ 3.880718@3] hdmitx: audio: set audio param
[ 4.095050@1] aml_snd_card: headphone detection disable=1
[ 4.095080@1] aml_snd_card: no spk event delay time set
[ 4.100508@1] aml_snd_m8_card aml_m8_snd.47: T9015-audio-hifi <-> I2S.40 mapping ok
[ 4.108106@1] aml_snd_m8_card aml_m8_snd.47: dit-hifi <-> SPDIF.41 mapping ok
[ 4.114730@1] aml_pcm: enter aml_pcm_new dai->name: PCM.42 dai->id: 0
[ 4.121186@1] aml_snd_m8_card aml_m8_snd.47: pcm2bt-pcm <-> PCM.42 mapping ok
[ 4.128131@1] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTL
[ 4.135698@1] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
[ 4.144489@1] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTR
[ 4.152083@1] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
[ 4.162706@0] GACT probability NOT on
[ 4.164507@0] Mirror/redirect action on
[ 4.168382@0] u32 classifier
[ 4.171137@0] Actions configured
[ 4.174677@0] Netfilter messages via NETLINK v0.30.
[ 4.179571@0] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 4.186254@0] ctnetlink v0.93: registering with nfnetlink.
[ 4.191657@0] xt_time: kernel timezone is -0000
[ 4.195735@0] ipip: IPv4 over IPv4 tunneling driver
[ 4.201302@0] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 4.206076@0] arp_tables: (C) 2002 David S. Miller
[ 4.210703@0] TCP: cubic registered
[ 4.214090@0] Initializing XFRM netlink socket
[ 4.219449@0] NET: Registered protocol family 10
[ 4.224134@0] mip6: Mobile IPv6
[ 4.226232@0] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 4.231955@0] sit: IPv6 over IPv4 tunneling driver
[ 4.237873@0] NET: Registered protocol family 17
[ 4.241039@0] NET: Registered protocol family 15
[ 4.245767@0] Bridge firewalling registered
[ 4.249803@0] Bluetooth: RFCOMM TTY layer initialized
[ 4.254800@0] Bluetooth: RFCOMM socket layer initialized
[ 4.260017@0] Bluetooth: RFCOMM ver 1.11
[ 4.263872@0] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.269376@0] Bluetooth: BNEP filters: protocol multicast
[ 4.274653@0] Bluetooth: BNEP socket layer initialized
[ 4.279756@0] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 4.285812@0] Bluetooth: HIDP socket layer initialized
[ 4.290909@0] l2tp_core: L2TP core driver, V2.0
[ 4.295365@0] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 4.300254@0] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 4.306022@0] l2tp_netlink: L2TP netlink interface
[ 4.310727@0] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 4.316763@0] l2tp_debugfs: L2TP debugfs support
[ 4.321333@0] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 4.327919@0] NET: Registered protocol family 35
[ 4.332503@0] Key type dns_resolver registered
[ 4.338292@0] Registering SWP/SWPB emulation handler
[ 4.342485@0] regulator-dummy: disabling
[ 4.346086@0] aml_vrtc rtc.32: setting system clock to 2015-01-01 00:00:06 UTC (1420070406)
[ 4.356138@0] gxbb_pm: enter meson_pm_probe!
[ 4.358164@0] gxbb_pm: meson_pm_probe done
[ 4.363023@0] cpucore_cooling_register, max_cpu_core_num:4
[ 4.367971@0] cpucore_cooling_register, max_cpu_core_num:4
[ 4.388288@0] aml_istbt_dev_ready NULL
[ 4.38834[ 4.393035@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 4.396489@0] Freeing unused kernel memory: 1260K (ffffffc001eaa000 - ffffffc001fe5000)
[ 4.425049@2] init: init started!
[ 4.426555@2] init: init second stage started!
[ 4.427565@2] init: waitpid failed: No child processes
[ 4.432383@2] init: (Loading properties from /default.prop took 0.00s.)
[ 4.440448@2] init: (Parsing /init.environ.rc took 0.00s.)
[ 4.444433@2] init: (Parsing /init.usb.rc took 0.00s.)
[ 4.450283@2] init: (Parsing init.amlogic.usb.rc took 0.00s.)
[ 4.455485@2] init: (Parsing init.amlogic.usb.rc took 0.00s.)
[ 4.460700@2] init: (Parsing init.amlogic.board.rc took 0.01s.)
[ 4.466631@2] init: could not import file 'init.amlogic.wifi.rc' from '/init.amlogic.rc'
[ 4.474595@2] init: could not import file 'init.mtk.rc' from '/init.amlogic.rc'
[ 4.481855@2] init: (Parsing /init.amlogic.rc took 0.03s.)
[ 4.487742@2] init: (Parsing /init.usb.configfs.rc took 0.00s.)
[ 4.493190@2] init: (Parsing /init.zygote32.rc took 0.00s.)
[ 4.498783@2] init: (Parsing /init.trace.rc took 0.00s.)
[ 4.503910@2] init: (Parsing /init.rc took 0.06s.)
[ 4.509020@2] init: Starting service 'ueventd'...
[ 4.515317@2] ueventd: ueventd started!
[ 4.777036@3] ueventd: Coldboot took 0.26s.
[ 4.786674@6] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 4.810875@6] init: enter do_confirm_formated /dev/block/tee, /tee
[ 4.811434@6] init: blocksize 1024, bytes_per_inode 1024
[ 4.816719@6] init: do_confirm_formated ext4 try mount
[ 4.832632@6] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
[ 4.902017@3] EXT4-fs (mmcblk0p13): mounted filesystem with ordered data mode. Opts: (null)
[ 4.904781@3] fs_mgr: __mount(source=/dev/block/system,target=/system,type=ext4)=0
[ 4.912912@3] EXT4-fs (mmcblk0p14): Ignoring removed nomblk_io_submit option
[ 4.923477@3] EXT4-fs (mmcblk0p14): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 4.929983@3] fs_mgr: check_fs(): mount(/dev/block/data,/data,ext4)=0: Success
[ 4.996403@4] fs_mgr: check_fs(): unmount(/data) succeeded
[ 4.997333@4] fs_mgr: Running /system/bin/e2fsck on /dev/block/data
[ 5.080162@4] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 5.080162@4]
[ 5.080918@4] e2fsck: /dev/block/data: clean, 6205/727664 files, 222778/2905088 blocks
[ 5.080918@4]
[ 5.091156@4] EXT4-fs (mmcblk0p14): Ignoring removed nomblk_io_submit option
[ 5.102052@4] EXT4-fs (mmcblk0p14): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
[ 5.108675@4] fs_mgr: __mount(source=/dev/block/data,target=/data,type=ext4)=0
[ 5.116418@1] EXT4-fs (mmcblk0p3): Ignoring removed nomblk_io_submit option
[ 5.126487@1] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 5.133290@1] fs_mgr: check_fs(): mount(/dev/block/cache,/cache,ext4)=0: Success
[ 5.176232@1] fs_mgr: check_fs(): unmount(/cache) succeeded
[ 5.176298@1] fs_mgr: Running /system/bin/e2fsck on /dev/block/cache
[ 5.203083@1] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 5.203083@1]
[ 5.203820@1] e2fsck: /dev/block/cache: clean, 21/32768 files, 4234/131072 blocks
[ 5.203820@1]
[ 5.213494@1] EXT4-fs (mmcblk0p3): Ignoring removed nomblk_io_submit option
[ 5.223578@1] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
[ 5.230954@1] fs_mgr: __mount(source=/dev/block/cache,target=/cache,type=ext4)=0
[ 5.239034@1] EXT4-fs (mmcblk0p8): Ignoring removed nomblk_io_submit option
[ 5.247664@1] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 5.255784@1] fs_mgr: check_fs(): mount(/dev/block/tee,/tee,ext4)=0: Success
[ 5.306190@1] fs_mgr: check_fs(): unmount(/tee) succeeded
[ 5.306257@1] fs_mgr: Running /system/bin/e2fsck on /dev/block/tee
[ 5.330918@1] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 5.330918@1]
[ 5.331663@1] e2fsck: /dev/block/tee: clean, 11/8192 files, 3111/8192 blocks
[ 5.331663@1]
[ 5.340914@1] EXT4-fs (mmcblk0p8): Ignoring removed nomblk_io_submit option
[ 5.349745@1] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
[ 5.358377@1] fs_mgr: __mount(source=/dev/block/tee,target=/tee,type=ext4)=0
[ 5.390691@6] Adding 511996k swap on /dev/block/zram0. Priority:-1 extents:1 across:511996k SS
[ 5.432098@6] EXT4-fs (zram0): mounted filesystem with ordered data mode. Opts: (null)
[ 5.437341@7] init: cannot find '/system/bin/tee-supplicant', disabling 'tee_supplicant'
[ 5.457989@7] init: /recovery not specified in fstab
[ 5.464277@0] logd.auditd: start
[ 5.492343@2] init: Failed to reload policy
[ 5.578467@3] dig: dig start!
[ 5.709064@2] mali_kbase: unknown parameter 'mali_debug_level' ignored
[ 5.709957@2] mali_kbase: unknown parameter 'mali_shared_mem_size' ignored
[ 5.719113@2] ftrace: Allocated trace_printk buffers
[ 5.724086@2] mali d00c0000.t82x: Continuing without Mali regulator control
[ 5.728687@2] mali d00c0000.t82x: set min pp to default 1
[ 5.733931@2] mali d00c0000.t82x: set min clk default to 0
[ 5.739466@2] mali d00c0000.t82x: dvfs table is 5
[ 5.744021@2] mali d00c0000.t82x: dvfs table addr ffffffc063be1c18, ele size=48
[ 5.751298@2] mali d00c0000.t82x: max clk set 3
[ 5.755790@2] mali d00c0000.t82x: turbo clk set to 4
[ 5.760667@2] mali d00c0000.t82x: default clk set to 1
[ 5.765843@2] mali_plat=ffffffbffc043568
[ 5.770048@2] gpu cooling register okay with err=0
[ 5.774551@2] gpu core cooling register okay with err=0
[ 5.779812@2] gpu_power_main, 63
[ 5.782889@2] hrtimer: interrupt took 11750 ns
[ 5.787369@0] mali d00c0000.t82x: GPU identified as 0x0820 r1p0 status 0
[ 5.794731@0] mali d00c0000.t82x: Probed as mali0
[ 5.805300@0] random: init urandom read with 81 bits of entropy available
[ 5.840116@1] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 5.841965@2] binder: 3765:3765 transaction failed 29189, size 0-0
[ 5.846899@0] amlkey_init() enter!
[ 5.853243@0] emmc_key_read:428, read ok
[ 5.856418@0] amlkey_init() storagekey_info.buffer=ffffff8001900000, storagekey_info.size = 40000!
[ 5.863133@1] logd.daemon: reinit
[ 5.866345@2] warning: `daemonsu' uses 32-bit capabilities (legacy support in use)
[ 5.877252@0] vfm_map_store:rm default
[ 5.879806@0] vfm_map_store:add default decoder ppmgr deinterlace amvideo
[ 5.886767@0] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
[ 5.896413@0] init: cannot expand '${ro.usb.vendor.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/vendor_string'
[ 5.908669@0] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
[ 5.918516@0] init: cannot expand '${ro.usb.product.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/product_string'
[ 5.931030@0] init: property_set("ro.radio.noril", "true" failed
[ 5.938123@0] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
[ 5.946625@0] init: cannot expand '${ro.usb.vendor.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/vendor_string'
[ 5.959086@0] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
[ 5.968873@0] init: cannot expand '${ro.usb.product.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/product_string'
[ 5.983351@0] init: cannot find '/system/bin/debuggerd64', disabling 'debuggerd64'
[ 5.989068@0] init: cannot find '/system/bin/rild', disabling 'ril-daemon'
[ 5.997436@0] init: cannot find '/system/bin/install-recovery.sh', disabling 'flash_recovery'
root@q201_9377:/ # [ 6.010719@0] init: cannot find '/system/xbin/perfprofd', disabling 'perfprofd'
[ 6.015081@1] init: cannot find '/system/bin/tee-supplicant', disabling 'tee_supplicant'
Hello Jten!!!
Hello Jten!!!
Hello Jten!!!
[ 6.083909@1] remote: cur_mode = 0
[ 6.083948@1] remote: set_remote_mode[74]
[ 6.087419@1] remote: cur_mode = 0
[ 6.089022@1] remote: set_remote_mode[74]
[ 6.214591@2] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 6.307563@6] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 6.463353@3] vout_serve: vmode set to 1080p60hz
[ 6.463386@3] vout_serve: don't set the same mode as current
[ 6.595828@6] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 6.665228@2] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 6.715804@4] fb: afbc: 1
[ 6.715866@4] fb: use ion buffer for fb memory
[ 6.717250@4] fb: OSD0 as afbcd mode
[ 6.720979@4] meson-fb meson-fb.16: create ion_client ffffffc065573600, handle=ffffffc061f04a40
[ 6.729547@4] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 8 MiB
[ 6.738048@4] fb: 0, phy: 0x0000000079300000, vir:0xffffff80034ff000, size=8300K
[ 6.738048@4]
[ 6.747317@1] meson-fb meson-fb.16: create ion_client ffffffc065573600, handle=ffffffc061fb8000
[ 6.755706@1] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079b1b000, size 8 MiB
[ 6.764307@1] fb: 0, phy: 0x0000000079b1b000, vir:0xffffff8003d1b000, size=8300K
[ 6.764307@1]
[ 6.773572@1] meson-fb meson-fb.16: create ion_client ffffffc065573600, handle=ffffffc061fb8ec0
[ 6.782183@1] meson-fb meson-fb.16: ion memory(0): created fb at 0x000000007a336000, size 8 MiB
[ 6.790650@1] fb: 0, phy: 0x000000007a336000, vir:0xffffff8004567000, size=8300K
[ 6.790650@1]
[ 6.799711@1] fb: Frame buffer memory assigned at
[ 6.804158@1] fb: 0, phy: 0x0000000079300000, vir:0xffffff80034ff000, size=8300K
[ 6.804158@1]
[ 6.813421@1] fb: 0, phy: 0x0000000079300000, vir:0xffffff80034ff000, size=8300K
[ 6.813421@1]
[ 6.822507@1] fb: 0, phy: 0x0000000079b1b000, vir:0xffffff8003d1b000, size=8300K
[ 6.822507@1]
[ 6.831550@1] fb: 0, phy: 0x000000007a336000, vir:0xffffff8004567000, size=8300K
[ 6.831550@1]
[ 6.840589@1] fb: ---------------clear fb0 memory ffffff80034ff000
[ 6.842717@7] healthd: No charger supplies found
[ 6.842730@7] healthd: No battery devices found
[ 6.857538@1] fb: ---------------clear fb0 memory ffffff8003d1b000
[ 6.863558@1] fb: ---------------clear fb0 memory ffffff8004567000
[ 6.869791@1] fb: osd[0] canvas.idx =0x40
[ 6.871940@1] fb: osd[0] canvas.addr=0x79300000
[ 6.876460@1] fb: osd[0] canvas.width=7680
[ 6.880478@1] fb: osd[0] canvas.height=3240
[ 6.884615@1] fb: osd[0] frame.width=1920
[ 6.888601@1] fb: osd[0] frame.height=1080
[ 6.930881@1] fb: afbc: 1
[ 6.931327@1] fb: use ion buffer for fb memory
[ 6.932346@1] meson-fb meson-fb.16: create ion_client ffffffc065573600, handle=ffffffc061170100
[ 6.941018@1] meson-fb meson-fb.16: ion memory(1): created fb at 0x000000007ab51000, size 1 MiB
[ 6.949564@1] fb: Frame buffer memory assigned at
[ 6.954017@1] fb: 1, phy: 0x000000007ab51000, vir:0xffffff8004fe8000, size=1024K
[ 6.954017@1]
[ 6.963262@1] fb: fb1 open, logo index:1
[ 7.170312@4] fb: osd[1] enable: 0 scale:0x0 (systemcontrol)
[ 7.170353@4] fb: osd[0] enable: 1 scale:0x10001 (systemcontrol)
[ 7.184146@4] fb: free_scale_switch to fb0, mode: 0x10001
[ 7.184536@4] vout_serve: osd0=> x:0,y:0,w:1920,h:1080
[ 7.184536@4] osd1=> x:0,y:0,w:18,h:18
[ 7.192779@4] fb: current vmode=1080p60hz
[ 7.201052@4] fb: osd[1] set scale, h_scale: ENABLE, v_scale: ENABLE
[ 7.202972@4] fb: osd[1].scaledata: 1920 1920 1080 1080
[ 7.208201@4] fb: osd[1].pandata: 0 0 0 0
[ 7.937591@0] random: nonblocking pool is initialized
[ 11.862140@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 11.862763@1] audio_dsp: last mode 0,now 0
[ 11.874987@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 11.875614@1] audio_dsp: last mode 0,now 0
[ 11.885317@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 11.885947@1] audio_dsp: last mode 0,now 0
[ 11.890069@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 11.896287@1] audio_dsp: last mode 0,now 0
[ 11.917333@7] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 11.917965@7] audio_dsp: last mode 0,now 0
[ 11.922075@7] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 11.928282@7] audio_dsp: last mode 0,now 0
[ 11.932881@7] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 11.938584@7] audio_dsp: last mode 0,now 0
[ 11.942613@7] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 11.948808@0] audio_dsp: last mode 0,now 0
[ 12.159796@3] tv_vout: vout [tv_set_vframe_rate_end_hint] return mode = 16, policy = 1!
root@q201_9377:/ # [ 40.886698@1] request_suspend_state: wakeup (3->0) at 40781863185 (2015-01-01 00:00:43.040624434 UTC)
[ 40.890261@1] request_suspend_state,168,old_sleep=0,new_state=0
[ 58.815963@5] lowmemorykiller: lowmem_shrink: convert oom_adj to oom_score_adj:
[ 58.817638@5] lowmemorykiller: oom_adj 0 => oom_score_adj 0
[ 58.823164@5] lowmemorykiller: oom_adj 2 => oom_score_adj 117
[ 58.828893@5] lowmemorykiller: oom_adj 4 => oom_score_adj 235
[ 58.834549@5] lowmemorykiller: oom_adj 6 => oom_score_adj 352
[ 58.840293@5] lowmemorykiller: oom_adj 9 => oom_score_adj 529
[ 58.845964@5] lowmemorykiller: oom_adj 15 => oom_score_adj 1000
[ 122.494732@6] avc open
[ 122.494766@6] amvenc_avc check CMA pool sucess, max instance: 2.
[ 122.497690@6] allocating phys 0x75200000, size 20480k, wq:ffffffc06113c000.
[ 122.504484@3] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc06113c000.
[ 122.514500@3] avc release, wq:ffffffc06113c000
[ 122.518787@3] remove encode_work_queue ffffffc06113c000 sucess, _destroy_encode_work_queue line 4285.
[ 122.530078@3] ionvid: info: ionvideo open
[ 122.724884@3] ionvid: info: ionvideo_stop_generating!!!!
[ 122.724940@3] ionvid: info: ionvideo release
[ 122.734218@4] ionvid: info: ionvideo open
[ 122.925017@7] ionvid: info: ionvideo_stop_generating!!!!
[ 122.925091@7] ionvid: info: ionvideo release
[ 122.932194@5] ionvid: info: ionvideo open
[ 123.124908@6] ionvid: info: ionvideo_stop_generating!!!!
[ 123.124969@6] ionvid: info: ionvideo release
[ 123.131908@7] ionvid: info: ionvideo open
[ 123.324887@5] ionvid: info: ionvideo_stop_generating!!!!
[ 123.324945@5] ionvid: info: ionvideo release
[ 123.331495@5] ionvid: info: ionvideo open
[ 123.524931@0] ionvid: info: ionvideo_stop_generating!!!!
[ 123.524990@0] ionvid: info: ionvideo release
[ 123.532167@5] ionvid: info: ionvideo open
[ 123.724916@7] ionvid: info: ionvideo_stop_generating!!!!
[ 123.724983@7] ionvid: info: ionvideo release
[ 123.732369@5] ionvid: info: ionvideo open
[ 123.924909@5] ionvid: info: ionvideo_stop_generating!!!!
[ 123.924989@5] ionvid: info: ionvideo release
[ 123.931722@6] ionvid: info: ionvideo open
[ 124.085306@5] libphy: stmmac-0:00 - Link is Up - 100/Full
[ 124.124928@5] ionvid: info: ionvideo_stop_generating!!!!
[ 124.125003@5] ionvid: info: ionvideo release
[ 124.131897@7] ionvid: info: ionvideo open
[ 124.324927@4] ionvid: info: ionvideo_stop_generating!!!!
[ 124.325002@4] ionvid: info: ionvideo release
[ 124.333212@7] ionvid: info: ionvideo open
[ 124.524885@7] ionvid: info: ionvideo_stop_generating!!!!
[ 124.524952@7] ionvid: info: ionvideo release
[ 124.694786@7] dig: isBootCompleted:1!
[ 124.695179@7] dig: setDataRoCount count:0!
[ 124.815279@7] avc open
[ 124.815329@7] allocating phys 0x75200000, size 20480k, wq:ffffffc05a16cc00.
[ 124.818927@7] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc05a16cc00.
[ 124.828994@7] avc release, wq:ffffffc05a16cc00
[ 124.833260@7] remove encode_work_queue ffffffc05a16cc00 sucess, _destroy_encode_work_queue line 4285.
[ 125.078526@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 125.078581@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 125.095254@3] xhci-hcd xhci-hcd.0.auto: irq 62, io mem 0xc9000000
[ 125.097346@2] hub 1-0:1.0: USB hub found
[ 125.099642@2] hub 1-0:1.0: 3 ports detected
[ 125.104066@2] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 125.109453@2] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 125.113958@1] avc open
[ 125.113980@1] allocating phys 0x75200000, size 20480k, wq:ffffffc063265c00.
[ 125.113983@1] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc063265c00.
[ 125.114054@1] avc release, wq:ffffffc063265c00
[ 125.114059@1] remove encode_work_queue ffffffc063265c00 sucess, _destroy_encode_work_queue line 4285.
[ 125.151689@2] hub 2-0:1.0: USB hub found
[ 125.153804@2] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 125.162889@2] file system registered
[ 125.171475@2] ffs_data_put(): freeing
[ 125.409275@3] avc open
[ 125.409319@3] allocating phys 0x75200000, size 20480k, wq:ffffffc0630ac000.
[ 125.412922@3] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc0630ac000.
[ 125.414958@7] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 125.429623@3] avc release, wq:ffffffc0630ac000
[ 125.433893@3] remove encode_work_queue ffffffc0630ac000 sucess, _destroy_encode_work_queue line 4285.
[ 125.598682@6] hub 1-1:1.0: USB hub found
[ 125.598804@6] hub 1-1:1.0: 3 ports detected
[ 125.707535@1] avc open
[ 125.707580@1] allocating phys 0x75200000, size 20480k, wq:ffffffc063e5e400.
[ 125.711193@1] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc063e5e400.
[ 125.721279@1] avc release, wq:ffffffc063e5e400
[ 125.725567@1] remove encode_work_queue ffffffc063e5e400 sucess, _destroy_encode_work_queue line 4285.
[ 125.874970@7] usb 1-1.2: new low-speed USB device number 3 using xhci-hcd
[ 125.984477@6] usb 1-1.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 125.988681@6] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 126.020425@3] avc open
[ 126.020470@3] allocating phys 0x75200000, size 20480k, wq:ffffffc0630ac000.
[ 126.024112@3] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc0630ac000.
[ 126.034113@3] avc release, wq:ffffffc0630ac000
[ 126.038692@3] remove encode_work_queue ffffffc0630ac000 sucess, _destroy_encode_work_queue line 4285.
[ 126.124966@4] usb 1-1.3: new low-speed USB device number 4 using xhci-hcd
[ 126.230552@4] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 126.243164@6] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0003/input/input3
[ 126.252079@4] hid-generic 0003:046D:C05A.0003: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 126.307482@3] avc open
[ 126.307530@3] allocating phys 0x75200000, size 20480k, wq:ffffffc0630ac000.
[ 126.311127@3] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc0630ac000.
[ 126.321154@3] avc release, wq:ffffffc0630ac000
[ 126.325458@3] remove encode_work_queue ffffffc0630ac000 sucess, _destroy_encode_work_queue line 4285.
[ 126.555253@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 126.555884@3] audio_dsp: last mode 0,now 0
[ 126.560003@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 126.566178@3] audio_dsp: last mode 0,now 0
[ 126.570371@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 126.576450@1] audio_dsp: last mode 0,now 0
[ 126.580536@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 126.586697@1] audio_dsp: last mode 0,now 0
[ 126.592429@7] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 126.597002@7] audio_dsp: last mode 0,now 0
[ 126.601067@7] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 126.607231@7] audio_dsp: last mode 0,now 0
[ 126.612486@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 126.617498@1] audio_dsp: last mode 0,now 0
[ 126.621561@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 126.627748@1] audio_dsp: last mode 0,now 0
[ 126.643209@5] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 126.643842@5] audio_dsp: last mode 0,now 0
[ 126.647983@5] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 126.654114@5] audio_dsp: last mode 0,now 0
[ 126.659232@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 126.664370@4] audio_dsp: last mode 0,now 0
[ 126.668609@0] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 126.674631@0] audio_dsp: last mode 0,now 0
[ 127.571523@5] audio_dsp: drc high cut scale set to 100%
[ 127.572115@6] audio_dsp: drc low boost scale set to 100%
[ 127.577183@6] audio_dsp: drc mode set to LINE
root@q201_9377:/ # [ 345.466687@6] fb: osd[1] canvas.idx =0x43
[ 345.466692@6] fb: osd[1] canvas.addr=0x7ab51000
[ 345.466697@6] fb: osd[1] canvas.width=192
[ 345.466699@6] fb: osd[1] canvas.height=42
[ 345.466701@6] fb: osd[1] frame.width=48
[ 345.466704@6] fb: osd[1] frame.height=42
[ 354.905284@6] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=48000, same source mode(1)
[ 354.907960@6] aml_spdif_dai: share the same clock
[ 354.907974@6] aml_spdif_dai: iec958 mode PCM16
[ 354.907985@6] aml_audio_hw: IEC958 16bit
[ 354.908003@6] hdmitx: audio: aout notify rate 48000
[ 354.908006@6] hdmitx: audio: aout notify size 16
[ 354.908010@6] hdmitx: audio: no update
[ 354.908031@6] aml_snd_m8_card aml_m8_snd.47: i2s/958 same source
[ 354.935522@6] aml_snd_m8_card aml_m8_snd.47: I2S playback enable
[ 354.935529@6] aml_snd_m8_card aml_m8_snd.47: IEC958 playback enable
[ 357.952333@7] aml_snd_m8_card aml_m8_snd.47: I2S playback disable
[ 357.952823@7] aml_snd_m8_card aml_m8_snd.47: IEC958 playback disable
[ 357.959436@7] aml_spdif_dai: share the same clock
[ 357.963776@7] aml_audio_hw: IEC958 16bit
[ 357.967729@7] hdmitx: audio: aout notify rate 48000
[ 357.972487@7] hdmitx: audio: aout notify size 16
[ 357.972492@7] hdmitx: audio: no update
[ 370.751471@6] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=48000, same source mode(1)
[ 370.753930@6] aml_spdif_dai: share the same clock
[ 370.758825@6] aml_spdif_dai: iec958 mode PCM16
[ 370.762994@6] aml_audio_hw: IEC958 16bit
[ 370.767022@6] hdmitx: audio: aout notify rate 48000
[ 370.771694@6] hdmitx: audio: aout notify size 16
[ 370.776338@6] hdmitx: audio: no update
[ 370.780053@6] aml_snd_m8_card aml_m8_snd.47: i2s/958 same source
[ 370.813139@1] aml_snd_m8_card aml_m8_snd.47: I2S playback enable
[ 370.813624@1] aml_snd_m8_card aml_m8_snd.47: IEC958 playback enable
[ 373.830572@7] aml_snd_m8_card aml_m8_snd.47: I2S playback disable
[ 373.831060@7] aml_snd_m8_card aml_m8_snd.47: IEC958 playback disable
[ 373.837555@7] aml_spdif_dai: share the same clock
[ 373.842014@7] aml_audio_hw: IEC958 16bit
[ 373.845926@7] hdmitx: audio: aout notify rate 48000
[ 373.850713@7] hdmitx: audio: aout notify size 16
[ 373.855325@7] hdmitx: audio: no update
[ 380.110101@5] [aml_is_card_insert] card OUT
[ 380.110139@5] card out
[ 380.111093@6] sd: card aaaa removed
root@q201_9377:/ # ifconfig
eth0 Link encap:Ethernet HWaddr 86:37:20:48:CB:3E
inet addr:192.168.2.124 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::8437:20ff:fe48:cb3e/64 Scope: Link
inet6 addr: 2003:86:8c3c:4870:8437:20ff:fe48:cb3e/64 Scope: Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:296 errors:0 dropped:0 overruns:0 frame:0
TX packets:164 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:102784 TX bytes:68225
Interrupt:40
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope: Host
UP LOOPBACK RUNNING MTU:4096 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 TX bytes:0
root@q201_9377:/ # uname -a
Linux localhost 3.14.29 #1 SMP PREEMPT Thu Jan 19 17:08:41 CST 2017 armv8l
root@q201_9377:/ # [ 408.548758@4] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=48000, same source mode(1)
[ 408.551213@4] aml_spdif_dai: share the same clock
[ 408.555990@4] aml_spdif_dai: iec958 mode PCM16
[ 408.560328@4] aml_audio_hw: IEC958 16bit
[ 408.560344@4] hdmitx: audio: aout notify rate 48000
[ 408.560347@4] hdmitx: audio: aout notify size 16
[ 408.560350@4] hdmitx: audio: no update
[ 408.560372@4] aml_snd_m8_card aml_m8_snd.47: i2s/958 same source
[ 408.598518@2] aml_snd_m8_card aml_m8_snd.47: I2S playback enable
[ 408.598998@2] aml_snd_m8_card aml_m8_snd.47: IEC958 playback enable
[ 411.615738@7] aml_snd_m8_card aml_m8_snd.47: I2S playback disable
[ 411.616250@7] aml_snd_m8_card aml_m8_snd.47: IEC958 playback disable
[ 411.622674@7] aml_spdif_dai: share the same clock
[ 411.627407@7] aml_audio_hw: IEC958 16bit
[ 411.631059@7] hdmitx: audio: aout notify rate 48000
[ 411.635923@7] hdmitx: audio: aout notify size 16
[ 411.640454@7] hdmitx: audio: no update
[ 414.760099@7] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=48000, same source mode(1)
[ 414.762586@7] aml_spdif_dai: share the same clock
[ 414.767443@7] aml_spdif_dai: iec958 mode PCM16
[ 414.771639@7] aml_audio_hw: IEC958 16bit
[ 414.775549@7] hdmitx: audio: aout notify rate 48000
[ 414.780321@7] hdmitx: audio: aout notify size 16
[ 414.784920@7] hdmitx: audio: no update
[ 414.788616@7] aml_snd_m8_card aml_m8_snd.47: i2s/958 same source
[ 414.820350@1] aml_snd_m8_card aml_m8_snd.47: I2S playback enable
[ 414.820722@1] aml_snd_m8_card aml_m8_snd.47: IEC958 playback enable
[ 417.837200@5] aml_snd_m8_card aml_m8_snd.47: I2S playback disable
[ 417.837687@5] aml_snd_m8_card aml_m8_snd.47: IEC958 playback disable
[ 417.844068@5] aml_spdif_dai: share the same clock
[ 417.848744@5] aml_audio_hw: IEC958 16bit
[ 417.852520@5] hdmitx: audio: aout notify rate 48000
[ 417.857406@5] hdmitx: audio: aout notify size 16
[ 417.861914@5] hdmitx: audio: no update
[ 434.141721@5] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=48000, same source mode(1)
[ 434.144185@5] aml_spdif_dai: share the same clock
[ 434.149998@5] aml_spdif_dai: iec958 mode PCM16
[ 434.153250@5] aml_audio_hw: IEC958 16bit
[ 434.157261@5] hdmitx: audio: aout notify rate 48000
[ 434.161950@5] hdmitx: audio: aout notify size 16
[ 434.166583@5] hdmitx: audio: no update
[ 434.170245@5] aml_snd_m8_card aml_m8_snd.47: i2s/958 same source
[ 434.203536@3] aml_snd_m8_card aml_m8_snd.47: I2S playback enable
[ 434.204019@3] aml_snd_m8_card aml_m8_snd.47: IEC958 playback enable
[ 437.221140@5] aml_snd_m8_card aml_m8_snd.47: I2S playback disable
[ 437.221622@5] aml_snd_m8_card aml_m8_snd.47: IEC958 playback disable
[ 437.228005@5] aml_spdif_dai: share the same clock
[ 437.232572@5] aml_audio_hw: IEC958 16bit
[ 437.236475@5] hdmitx: audio: aout notify rate 48000
[ 437.241279@5] hdmitx: audio: aout notify size 16
[ 437.245896@5] hdmitx: audio: no update
[ 439.376295@5] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=48000, same source mode(1)
[ 439.378750@5] aml_spdif_dai: share the same clock
[ 439.383402@5] aml_spdif_dai: iec958 mode PCM16
[ 439.387993@5] aml_audio_hw: IEC958 16bit
[ 439.391693@5] hdmitx: audio: aout notify rate 48000
[ 439.396595@5] hdmitx: audio: aout notify size 16
[ 439.401086@5] hdmitx: audio: no update
[ 439.404804@5] aml_snd_m8_card aml_m8_snd.47: i2s/958 same source
[ 439.436130@2] aml_snd_m8_card aml_m8_snd.47: I2S playback enable
[ 439.436507@2] aml_snd_m8_card aml_m8_snd.47: IEC958 playback enable
[ 442.453731@6] aml_snd_m8_card aml_m8_snd.47: I2S playback disable
[ 442.454321@6] aml_snd_m8_card aml_m8_snd.47: IEC958 playback disable
[ 442.461071@6] aml_spdif_dai: share the same clock
[ 442.465367@6] aml_audio_hw: IEC958 16bit
[ 442.469127@6] hdmitx: audio: aout notify rate 48000
[ 442.473938@6] hdmitx: audio: aout notify size 16
[ 442.478682@6] hdmitx: audio: no update
[ 469.423823@5] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=48000, same source mode(1)
[ 469.426461@5] aml_spdif_dai: share the same clock
[ 469.430944@5] aml_spdif_dai: iec958 mode PCM16
[ 469.435375@5] aml_audio_hw: IEC958 16bit
[ 469.439218@5] hdmitx: audio: aout notify rate 48000
[ 469.444037@5] hdmitx: audio: aout notify size 16
[ 469.448647@5] hdmitx: audio: no update
[ 469.452358@5] aml_snd_m8_card aml_m8_snd.47: i2s/958 same source
[ 469.482379@2] aml_snd_m8_card aml_m8_snd.47: I2S playback enable
[ 469.482756@2] aml_snd_m8_card aml_m8_snd.47: IEC958 playback enable
[ 472.872604@7] aml_snd_m8_card aml_m8_snd.47: I2S playback disable
[ 472.873091@7] aml_snd_m8_card aml_m8_snd.47: IEC958 playback disable
[ 472.879572@7] aml_spdif_dai: share the same clock
[ 472.884043@7] aml_audio_hw: IEC958 16bit
[ 472.888005@7] hdmitx: audio: aout notify rate 48000
[ 472.892788@7] hdmitx: audio: aout notify size 16
[ 472.897384@7] hdmitx: audio: no update
[ 474.865123@7] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=48000, same source mode(1)
[ 474.867563@7] aml_spdif_dai: share the same clock
[ 474.872219@7] aml_spdif_dai: iec958 mode PCM16
[ 474.876816@7] aml_audio_hw: IEC958 16bit
[ 474.880503@7] hdmitx: audio: aout notify rate 48000
[ 474.885368@7] hdmitx: audio: aout notify size 16
[ 474.889899@7] hdmitx: audio: no update
[ 474.893616@7] aml_snd_m8_card aml_m8_snd.47: i2s/958 same source
[ 474.924489@2] aml_snd_m8_card aml_m8_snd.47: I2S playback enable
[ 474.924971@2] aml_snd_m8_card aml_m8_snd.47: IEC958 playback enable
[ 486.145088@4] aml_snd_m8_card aml_m8_snd.47: I2S playback disable
[ 486.145576@4] aml_snd_m8_card aml_m8_snd.47: IEC958 playback disable
[ 486.151940@4] aml_spdif_dai: share the same clock
[ 486.156578@4] aml_audio_hw: IEC958 16bit
[ 486.160426@4] hdmitx: audio: aout notify rate 48000
[ 486.165278@4] hdmitx: audio: aout notify size 16
[ 486.169797@4] hdmitx: audio: no update
[ 486.712050@5] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=48000, same source mode(1)
[ 486.714510@5] aml_spdif_dai: share the same clock
[ 486.719277@5] aml_spdif_dai: iec958 mode PCM16
[ 486.723589@5] aml_audio_hw: IEC958 16bit
[ 486.727800@5] hdmitx: audio: aout notify rate 48000
[ 486.732278@5] hdmitx: audio: aout notify size 16
[ 486.736983@5] hdmitx: audio: no update
[ 486.740625@5] aml_snd_m8_card aml_m8_snd.47: i2s/958 same source
[ 486.767792@1] aml_snd_m8_card aml_m8_snd.47: I2S playback enable
[ 486.768271@1] aml_snd_m8_card aml_m8_snd.47: IEC958 playback enable
[ 489.786509@6] aml_snd_m8_card aml_m8_snd.47: I2S playback disable
[ 489.787098@6] aml_snd_m8_card aml_m8_snd.47: IEC958 playback disable
[ 489.793619@6] aml_spdif_dai: share the same clock
[ 489.798180@6] aml_audio_hw: IEC958 16bit
[ 489.801904@6] hdmitx: audio: aout notify rate 48000
[ 489.806911@6] hdmitx: audio: aout notify size 16
[ 489.811259@6] hdmitx: audio: no update
[ 492.031284@4] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=48000, same source mode(1)
[ 492.033793@4] aml_spdif_dai: share the same clock
[ 492.038582@4] aml_spdif_dai: iec958 mode PCM16
[ 492.042806@4] aml_audio_hw: IEC958 16bit
[ 492.046735@4] hdmitx: audio: aout notify rate 48000
[ 492.051533@4] hdmitx: audio: aout notify size 16
[ 492.056174@4] hdmitx: audio: no update
[ 492.059813@4] aml_snd_m8_card aml_m8_snd.47: i2s/958 same source
[ 492.092727@3] aml_snd_m8_card aml_m8_snd.47: I2S playback enable
[ 492.093206@3] aml_snd_m8_card aml_m8_snd.47: IEC958 playback enable
[ 495.110210@6] aml_snd_m8_card aml_m8_snd.47: I2S playback disable
[ 495.110705@6] aml_snd_m8_card aml_m8_snd.47: IEC958 playback disable
[ 495.117191@6] aml_spdif_dai: share the same clock
[ 495.121649@6] aml_audio_hw: IEC958 16bit
[ 495.125552@6] hdmitx: audio: aout notify rate 48000
[ 495.130348@6] hdmitx: audio: aout notify size 16
[ 495.134935@6] hdmitx: audio: no update
[ 496.991638@5] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=48000, same source mode(1)
[ 496.994104@5] aml_spdif_dai: share the same clock
[ 496.998922@5] aml_spdif_dai: iec958 mode PCM16
[ 497.003214@5] aml_audio_hw: IEC958 16bit
[ 497.007239@5] hdmitx: audio: aout notify rate 48000
[ 497.011893@5] hdmitx: audio: aout notify size 16
[ 497.016605@5] hdmitx: audio: no update
[ 497.020164@5] aml_snd_m8_card aml_m8_snd.47: i2s/958 same source
[ 497.051714@3] aml_snd_m8_card aml_m8_snd.47: I2S playback enable
[ 497.052092@3] aml_snd_m8_card aml_m8_snd.47: IEC958 playback enable
[ 502.703937@7] aml_snd_m8_card aml_m8_snd.47: I2S playback disable
[ 502.704427@7] aml_snd_m8_card aml_m8_snd.47: IEC958 playback disable
[ 502.710978@7] aml_spdif_dai: share the same clock
[ 502.715423@7] aml_audio_hw: IEC958 16bit
[ 502.719262@7] hdmitx: audio: aout notify rate 48000
[ 502.724090@7] hdmitx: audio: aout notify size 16
[ 502.724094@7] hdmitx: audio: no update
[ 509.717161@6] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=48000, same source mode(1)
[ 509.719617@6] aml_spdif_dai: share the same clock
[ 509.724303@6] aml_spdif_dai: iec958 mode PCM16
[ 509.724317@6] aml_audio_hw: IEC958 16bit
[ 509.724330@6] hdmitx: audio: aout notify rate 48000
[ 509.724333@6] hdmitx: audio: aout notify size 16
[ 509.724336@6] hdmitx: audio: no update
[ 509.724353@6] aml_snd_m8_card aml_m8_snd.47: i2s/958 same source
[ 509.747589@5] aml_snd_m8_card aml_m8_snd.47: I2S playback enable
[ 509.747597@5] aml_snd_m8_card aml_m8_snd.47: IEC958 playback enable
[ 544.838917@4] aml_snd_m8_card aml_m8_snd.47: I2S playback disable
[ 544.839381@4] aml_snd_m8_card aml_m8_snd.47: IEC958 playback disable
[ 544.845754@4] aml_spdif_dai: share the same clock
[ 544.850335@4] aml_audio_hw: IEC958 16bit
[ 544.854209@4] hdmitx: audio: aout notify rate 48000
[ 544.859097@4] hdmitx: audio: aout notify size 16
[ 544.863608@4] hdmitx: audio: no update
root@q201_9377:/ #
root@q201_9377:/ # reboot
[ 759.810536@4] SysRq : Emergency Remount R/O
[ 759.845656@7] EXT4-fs (mmcblk0p14): re-mounted. Opts: (null)
[ 759.869968@7] EXT4-fs (mmcblk0p3): re-mounted. Opts: (null)
[ 759.871320@7] EXT4-fs (mmcblk0p8): re-mounted. Opts: (null)
[ 759.880529@7] EXT4-fs (zram0): re-mounted. Opts: (null)
[ 759.887647@7] Emergency Remount complete
[ 759.915977@6] avmute set to 2
[ 761.228849@0] aml_snd_card: no audio pin_ctrl to shutdown
[ 761.230177@0] sysled: module shutdown ok
[ 761.232797@0] reboot: Restarting system(init) with command ''
[ 761.238480@0] reboot reason 1
INFO: PSCI Affinity Map:
INFO: AffInst: Level 1, MPID 0x0, State ON
INFO: AffInst: Level 1, MPID 0x100, State ON
INFO: AffInst: Level 0, MPID 0x0, State ON
INFO: AffInst: Level 0, MPID 0x1, State ON
INFO: AffInst: Level 0, MPID 0x2, State ON
INFO: AffInst: Level 0, MPID 0x3, State ON
INFO: AffInst: Level 0, MPID 0x100, State ON
INFO: AffInst: Level 0, MPID 0x101, State ON
INFO: AffInst: Level 0, MPID 0x102, State ON
INFO: AffInst: Level 0, MPID 0x103, State ON
bl31 reboot reason: 0xd
bl31 reboot reason: 0x1
system cmd 1.
GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 229577
BL2 Built : 19:58:22, Aug 31 2016.
gxl g54c8aee - xiaobo.gu@droid05
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00015400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a9a00
NOTICE: BL3-1: v1.0(debug):2e39a99
NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
aml log : bl31 normal boot !
wdt: reset registers!
[Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
OPS=0x82
fc c2 9 21 fb ca c 14 7e b4 40 63 [0.477389 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gd267f87 (Jan 19 2017 - 16:49:10)
DRAM: 2 GiB
Relocation Offset is: 76ec9000
register usb cfg[0][1] = 0000000077f5f5d8
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073ec96b0
aml_priv->desc_buf = 0x0000000073ecb9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ece270,dt_addr=0000000073ed9270
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000080000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 80000000 1
13: data d7c00000 2c5400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=normal
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 4 vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
rx version is 1.4 or below div=10
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[CANVAS]canvas init
[CANVAS]addr=0x3d851000 width=5760, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
get_cpu_id flag_12bit=1
SARADC open channel(0).
SARADC channel(0) is 0x3c7, Out of range(0x0~0x50)!
saradc - saradc sub-system
Usage:
saradc saradc open <channel> - open a SARADC channel
saradc close - close the SARADC
saradc getval - get the value in current channel
saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
get_cpu_id flag_12bit=1
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =73f4e440
copy done
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x02106540
Loading Ramdisk to 73dd7000, end 73eb6f66 ... OK
Loading Device Tree to 000000001fff2000, end 000000001ffff1ca ... OK
signature:
fdt_instaboot: no instaboot image
Starting kernel ...
uboot time: 2090443 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-g6bba886 (lhh@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Thu Jan 19 17:08:41 CST 2017
[ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000@0] no prop version_code
[ 0.000000@0] bootconsole [earlycon0] enabled
[ 0.000000@0] fdt Reserved memory table:
[ 0.000000@0] linux,di: 0x000000007d300000 - 0x000000007f100000 (30 MiB)
[ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007d300000, size 30 MiB
[ 0.000000@0] linux,ion-dev: 0x0000000079300000 - 0x000000007d300000 (64 MiB)
[ 0.000000@0] linux,ppmgr: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] linux,codec_mm_cma: 0x0000000067c00000 - 0x0000000073c00000 (192 MiB)
[ 0.000000@0] linux,picdec: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] Reserved memory: incorrect alignment of CMA region
[ 0.000000@0] linux,codec_mm_reserved: 0x0000000075200000 - 0x0000000079300000 (65 MiB)
[ 0.000000@0] fdt Reserved memory total: 354 MiB
[ 0.000000@0] cma: Reserved 8 MiB at 74800000
[ 0.000000@0] psci: probing function IDs from device-tree
[ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc07516e000 s19968 r8192 d20992 u49152
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 510280
[ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=disabled logo=osd1,loaded,0x3d800000,1080p60hz maxcpus=8 vout=1080p60hz,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 androidboot.firstboot=0 jtag=apao androidboot.hardware=amlogic mac=86:37:20:48:cb:3e androidboot.mac=86:37:20:48:cb:3e
[ 0.000000@0] logo: osd1
[ 0.000000@0] logo: loaded
[ 0.000000@0] logo: 0x3d800000
[ 0.000000@0] logo: 1080p60hz
[ 0.000000@0] vout_serve: 1080p60hz
[ 0.000000@0] vout_serve: enable: 1
[ 0.000000@0] logo: get hdmimode: 1080p60hz
[ 0.000000@0] logo: get cvbsmode: 576cvbs
[ 0.000000@0] tv_vout: cvbs performance line = 0
[ 0.000000@0] jtag: jtag select 2
[ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000@0] Memory: 1643716K/2077696K available (10612K kernel code, 1153K rwdata, 3884K rodata, 1263K init, 5869K bss, 433980K reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
[ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff80423cc800 ( 35 MB)
[ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc07f100000 ( 2033 MB)
[ 0.000000@0] .init : 0xffffffc001eaa000 - 0xffffffc001fe5e00 ( 1264 kB)
[ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001ea9334 ( 14501 kB)
[ 0.000000@0] .data : 0xffffffc001fe6000 - 0xffffffc002106540 ( 1154 kB)
[ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01ea8fff]
[ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000@0] arch_multi_cluster:1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[ 0.008245@0] meson_bc_timer: mclk->mux_reg =ffffff8000014990,mclk->reg =ffffff8000016994
[ 0.016822@0] Console: colour dummy device 80x25
[ 0.021096@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.031671@0] pid_max: default: 32768 minimum: 301
[ 0.036580@0] Security Framework initialized
[ 0.040786@0] SELinux: Initializing.
[ 0.044532@0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.051367@0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.061616@0] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
[ 0.065714@0] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
[ 0.072720@0] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
[ 0.079712@0] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
[ 0.090048@0] Initializing cgroup subsys debug
[ 0.091175@0] Initializing cgroup subsys freezer
[ 0.095843@0] ftrace: allocating 36489 entries in 143 pages
[ 0.149533@0] /cpus/cpu@0: Missing clock-frequency property
[ 0.149576@0] /cpus/cpu@1: Missing clock-frequency property
[ 0.155155@0] /cpus/cpu@2: Missing clock-frequency property
[ 0.160784@0] /cpus/cpu@3: Missing clock-frequency property
[ 0.166356@0] /cpus/cpu@100: Missing clock-frequency property
[ 0.172138@0] /cpus/cpu@101: Missing clock-frequency property
[ 0.177907@0] /cpus/cpu@102: Missing clock-frequency property
[ 0.183689@0] /cpus/cpu@103: Missing clock-frequency property
[ 0.189456@0] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 0.239806@0] Meson chip version = RevA (22:A - 82:0)
[ 0.258211@1] CPU1: Booted secondary processor
[ 0.278178@2] CPU2: Booted secondary processor
[ 0.298188@3] CPU3: Booted secondary processor
[ 0.318217@4] CPU4: Booted secondary processor
[ 0.338216@5] CPU5: Booted secondary processor
[ 0.358229@6] CPU6: Booted secondary processor
[ 0.378251@7] CPU7: Booted secondary processor
[ 0.378343@0] Brought up 8 CPUs
[ 0.407163@0] SMP: Total of 8 processors activated.
[ 0.420139@2] sched: registering cpufreq notifiers for scale-invariant loads
[ 0.421661@2] instabooting: 0
[ 0.433837@2] pinctrl core: initialized pinctrl subsystem
[ 0.434537@2] regulator-dummy: no parameters
[ 0.438828@2] NET: Registered protocol family 16
[ 0.444445@3] ramoops: using module parameters
[ 0.448217@2] console [pstore-1] enabled
[ 0.451020@2] pstore: Registered ramoops as persistent store backend
[ 0.457395@2] ramoops: attached 0x100000@0x7300000, ecc: 0/0
[ 0.464021@3] cpuidle: using governor menu
[ 0.467463@3] aml_vdac_init: module init
[ 0.471350@2] register canvas platform driver
[ 0.475630@2] register rdma platform driver
[ 0.481325@2] vdso: 2 pages (1 code, 1 data) at base ffffffc001ff0000
[ 0.486239@2] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.493564@2] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.500484@2] software IO TLB [mem 0x64800000-0x64c00000] (4MB) mapped at [ffffffc064800000-ffffffc064bfffff]
[ 0.509459@2] Serial: AMBA PL011 UART driver
[ 0.514326@3] aml_i2c version: 20140813
[ 0.517857@3] i2c-core: driver [pmu4] using legacy resume method
[ 0.523845@2] codec_mm:codec_mm_module_init
[ 0.528089@3] aml_watch_point_probe, in
[ 0.532148@2] gxbb_mpll_clk: register mpll_clk_out0 success done
[ 0.537745@2] gxbb_mpll_clk: register mpll_clk_out1 success done
[ 0.543760@2] gxbb_mpll_clk: register mpll_clk_out2 success done
[ 0.550007@2] clk_sys: register PLL sys_pll success done
[ 0.555141@2] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
[ 0.560504@2] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
[ 0.565633@2] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
[ 0.571151@2] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
[ 0.577095@2] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
[ 0.583063@2] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
[ 0.588907@2] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
[ 0.594775@2] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
[ 0.600632@2] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
[ 0.606529@2] gxl_clk: clock initialization complete
[ 0.611684@2] clkmsr: Gxl msr_clk_reg0=ffffff800003c75c,msr_clk_reg2=ffffff800003e764
[ 0.621969@2] aml_iomap: amlogic iomap probe done
[ 0.624734@2] pinmux-gxl c1109880.pinmux: Init pinux probe!
[ 0.630671@2] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
[ 0.636904@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.644411@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ 0.652635@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.660504@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
domain-0 init dvfs: 4
domain-1 init dvfs: 4
[ 0.680697@2] codec_mm has 2 memory regions
[ 0.680766@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.687370@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.695984@3] codec_mm has 2 memory regions
[ 0.700066@3] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.708119@3] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.718697@2] vpu: driver version: v02
[ 0.720377@2] vpu: load vpu_clk: 666667000Hz(7)
[ 0.724992@2] vpu: vpu_probe OK
[ 0.729815@2] tv_vout: tvout_probe
[ 0.731472@2] tv_vout: major number 254 for disp
[ 0.736100@2] vout_notify: vout_register_server
[ 0.740662@2] tv_vout: register tv module server ok
[ 0.745660@2] tv_vout: tvout_probe OK
[ 0.749897@2] canvas_probe reg=00000000c8838000,size=400
[ 0.754623@2] canvas maped reg_base =ffffff800009a000
[ 0.763919@2] rdma_probe
[ 1.077166@0] bio: create slab <bio-0> at 0
[ 1.078323@3] SCSI subsystem initialized
[ 1.080440@3] usbcore: registered new interface driver usbfs
[ 1.085513@3] usbcore: registered new interface driver hub
[ 1.091119@0] usbcore: registered new device driver usb
[ 1.097159@3] i2c-gpio i2c_gpio.38: using pins 172 (SDA) and 173 (SCL)
[ 1.103245@3] Linux video capture interface: v2.00
[ 1.107794@3] pps_core: LinuxPPS API ver. 1 registered
[ 1.112712@3] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 1.122638@0] PTP clock support registered
[ 1.126895@3] hdmitx: system: amhdmitx_init
[ 1.130386@3] hdmitx: system: Ver: 2014May6
[ 1.134833@3] hdmitx: system: amhdmitx_probe
[ 1.139217@3] hdmitx: system: not find match init-data
[ 1.144035@3] hdmitx: system: not find match pwr-ctl
[ 1.149086@3] hdmitx hpd irq = 89
[ 1.152844@3] hdmitx20: Mapped PHY: 0xc0800000
[ 1.156819@3] hdmitx20: Mapped PHY: 0xc1104400
[ 1.161303@3] hdmitx20: Mapped PHY: 0xc8100000
[ 1.165737@3] hdmitx20: Mapped PHY: 0xc8834000
[ 1.170196@3] hdmitx20: Mapped PHY: 0xc883a000
[ 1.174722@3] hdmitx20: Mapped PHY: 0xc883c000
[ 1.179126@3] hdmitx20: Mapped PHY: 0xd0100000
[ 1.183585@3] hdmitx20: Mapped PHY: 0xda83a000
[ 1.188059@3] hdmitx: alread display in uboot 0x10
[ 1.192877@3] avmute set to 1
[ 1.196258@3] vout_serve: vout_init_module
[ 1.200137@3] tv_vout: tv_set_current_vmode[759]fps_target_mode=16
[ 1.202930@0] hdmitx: system: irq 80000002
[ 1.210282@3] tv_vout: mode is 16,sync_duration_den=1,sync_duration_num=60
[ 1.217188@3] tv_vout: already display in uboot
[ 1.221743@3] vout_serve: vinfo mode is: 1080p60hz
[ 1.226546@3] vout_serve: init mode 1080p60hz
[ 1.231050@2] vout_serve: create vout attribute OK
[ 1.235741@2] vout_serve: meson_vout_probe OK
[ 1.240318@2] logo: logo_init
[ 1.243468@2] osd_rdma: osd_rdma_init: rdma_table p=0x74841000,op=0x74841000 , v=0xffffff800009e000
[ 1.252210@2] osd_rdma: osd rdma request irq as second interrput function!
[ 1.259607@2] Advanced Linux Sound Architecture Driver Initialized.
[ 1.266069@2] Bluetooth: Core ver 2.18
[ 1.269297@2] NET: Registered protocol family 31
[ 1.273797@2] Bluetooth: HCI device and connection manager initialized
[ 1.280381@2] Bluetooth: HCI socket layer initialized
[ 1.285437@2] Bluetooth: L2CAP socket layer initialized
[ 1.290718@2] Bluetooth: SCO socket layer initialized
[ 1.296257@2] cfg80211: Calling CRDA to update world regulatory domain
[ 1.302474@0] NetLabel: Initializing
[ 1.305909@0] NetLabel: domain hash size = 128
[ 1.310523@0] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.315682@0] NetLabel: unlabeled traffic allowed by default
[ 1.323420@1] Switched to clocksource arch_sys_counter
[ 1.373088@0] [amlatvdemod..]aml_atvdemod_init.
[ 1.373222@0] NET: Registered protocol family 2
[ 1.377217@0] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.384238@0] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 1.391115@0] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.397702@0] TCP: reno registered
[ 1.401056@0] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 1.407282@0] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 1.414455@0] NET: Registered protocol family 1
[ 1.418735@0] RPC: Registered named UNIX socket transport module.
[ 1.424577@0] RPC: Registered udp transport module.
[ 1.429458@0] RPC: Registered tcp transport module.
[ 1.434400@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.441225@0] aml_wifi wifi.33: [wifi_dev_probe] no power_on_pin2
[ 1.447152@0] aml_wifi wifi.33: [wifi_dev_probe] set pwm as 32k output
[ 1.453774@0] aml_wifi wifi.33: [wifi_dev_probe] dhd_static_buf setup
[ 1.460237@0] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem: WIFI MEM Allocated
[ 1.467880@0] aml_wifi wifi.33: [wifi_dev_probe] interrupt_pin=241
[ 1.474007@0] aml_wifi wifi.33: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
[ 1.481435@0] aml_wifi wifi.33: [wifi_dev_probe] power_on_pin=240
[ 1.487603@0] aml_wifi wifi.33: [wifi_dev_probe] clock_32k_pin=0
[ 1.493936@1] aml_wifi wifi.33: [wifi_setup_dt] wifi_setup_dt
[ 1.499409@1] aml_wifi wifi.33: [wifi_setup_dt] interrupt_pin(241)
[ 1.505607@1] aml_wifi wifi.33: [wifi_setup_dt] power_on_pin(240)
[ 1.512073@0] Unpacking initramfs...
[ 1.523579@3] hdmitx: plugin
[ 1.546644@0] Freeing initrd memory: 892K (ffffffc073dd7000 - ffffffc073eb6000)
[ 1.553267@0] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 1.555014@0] audit: initializing netlink subsys (disabled)
[ 1.560543@0] audit: type=2000 audit(1.470:1): initialized
[ 1.567123@0] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.580164@0] VFS: Disk quotas dquot_6.5.2
[ 1.580444@2] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.590572@2] NFS: Registering the id_resolver key type
[ 1.590643@2] Key type id_resolver registered
[ 1.595130@2] Key type id_legacy registered
[ 1.599198@2] NTFS driver 2.1.30 [Flags: R/O].
[ 1.604112@0] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.611706@0] fuse init (API version 7.22)
[ 1.615758@0] msgmni has been set to 3612
[ 1.620640@2] NET: Registered protocol family 38
[ 1.624341@2] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 1.631292@2] io scheduler noop registered
[ 1.635508@2] io scheduler deadline registered
[ 1.640098@0] io scheduler cfq registered (default)
[ 1.660350@3] hdmitx: edid: check sum valid
[ 1.660385@3] hdmitx: edid: check sum valid
[ 1.663173@3] hdmitx: edid: blk0 raw data
[ 1.667263@3] 00ffffffffffff001e6de37689bb02000b18010380502278eaca95a6554ea126
[ 1.667263@3] 0f50542108007140818081c0a9c0b300d1c0810001019d6770a0d0a022503020
[ 1.667263@3] 3a00204f3100001a000000fd00383d1e5a1e000a202020202020000000fc004c
[ 1.667263@3] 4720554c545241574944450a000000000000000000000000000000000000017c
[ 1.667263@3]
[ 1.667263@3]
[ 1.695361@1] meson-rng c8834000.rng: hwrng registered
[ 1.698988@1] loop: module loaded
[ 1.699595@2] zram: Created 1 device(s) ...
[ 1.700657@2] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.701483@2] tun: Universal TUN/TAP device driver, 1.6
[ 1.701486@2] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 1.730571@3] hdmitx: edid: blk1 raw data
[ 1.734617@3] 020317f14410040301230907078301000065030c0010009f3d70a0d0a0155030
[ 1.734617@3] 203a00204f3100001a7e4800e0a0381f4040403a00204f31000018011d007251
[ 1.734617@3] d01e206e285500204f3100001e8c0ad08a20e02d10103e9600204f3100001800
[ 1.734617@3] 0000ff003431314b4b484e35393038310a0000000000000000000000000000ce
[ 1.734617@3]
[ 1.734617@3]
[ 1.766959@3] EDID Parser:
[ 1.769707@3] hdmitx: edid: find IEEEOUT
[ 1.773626@3]
[ 1.775258@3] hdmitx: edid: check sum valid
[ 1.779457@3] hdmitx: edid: check sum valid
[ 1.783681@3] hdmitx: update RX hdr info 0
[ 1.789792@3] hdmitx: ddc rd8b error 0x3a 0x00 0x00
[ 1.794715@3] [RX]-receive ksv list len:1,depth:1,cas:0,dev:0
[ 1.798452@3] hdmitx: video: get current mode: 1080p60hz
[ 1.803791@3] hdmitx: update rx hdr info 0
[ 1.807910@3] hdmitx: get ext_name (null)
[ 1.811924@3] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 16
[ 1.818675@3] hdmtix: set audio
[ 1.821818@3] hdmitx tx_aud_src = 0
[ 1.825353@3] hdmitx: fs = 0, cd = 4, tmds_clk = 148500
[ 1.827689@1] libphy: stmmac: probed
[ 1.827694@1] eth0: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[ 1.827697@1] eth0: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07)
[ 1.828166@1] PPP generic driver version 2.4.2
[ 1.828379@1] PPP BSD Compression module registered
[ 1.828381@1] PPP Deflate Compression module registered
[ 1.828401@1] PPP MPPE Compression module registered
[ 1.828404@1] NET: Registered protocol family 24
[ 1.828559@2] usbcore: registered new interface driver asix
[ 1.828710@1] usbcore: registered new interface driver ax88179_178a
[ 1.828814@2] usbcore: registered new interface driver cdc_ether
[ 1.828912@1] usbcore: registered new interface driver net1080
[ 1.829011@2] usbcore: registered new interface driver cdc_subset
[ 1.829109@1] usbcore: registered new interface driver zaurus
[ 1.829240@2] usbcore: registered new interface driver cdc_ncm
[ 1.829558@2] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.829560@2] ehci-h20ahb: H20AHB-EHCI Host Controller driver
[ 1.829805@1] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.830171@1] usbcore: registered new interface driver cdc_acm
[ 1.830173@1] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.830288@2] usbcore: registered new interface driver usb-storage
[ 1.830511@2] usbcore: registered new interface driver usbserial
[ 1.831219@1] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff80000da000
[ 1.831439@2] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
[ 1.831465@2] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff80000ee080
[ 1.832100@2] mousedev: PS/2 mouse device common for all mice
[ 1.832600@1] usbcore: registered new interface driver xpad
[ 1.832816@1] i2c /dev entries driver
[ 1.833147@2] usbcore: registered new interface driver uvcvideo
[ 1.833148@2] USB Video Class driver (1.1.1)
[ 1.834115@2] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: [email protected]
[ 1.834215@2] Bluetooth: HCI UART driver ver 2.2
[ 1.834219@2] Bluetooth: HCI H4 protocol initialized
[ 1.834566@2] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
[ 1.836781@0] cpu cpu4: bL_cpufreq_init: CPU 4 initialized
[ 1.836938@0] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
[ 1.837221@2] CPUidle arm64: cpuidle init start!!
[ 1.837999@2] @@@@@@@@@@_____2______in dia_init()
[ 1.838235@2] ATVR driver - init called!
[ 1.838236@2] usbcore: registered new interface driver usbhid
[ 1.838237@2] usbhid: USB HID core driver
[ 1.838584@2] ashmem: initialized
[ 1.838723@0] logger: created 256K log 'log_main'
[ 1.838855@2] logger: created 256K log 'log_events'
[ 1.838975@0] logger: created 256K log 'log_radio'
[ 1.839114@2] logger: created 256K log 'log_system'
[ 1.840225@0] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff80000fc4c0
[ 1.840247@0] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
[ 2.110754@3] hdmitx aud_n_para = 6144
[ 2.114524@3] hdmitx set channel status
[ 2.123862@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
[ 2.126491@0] console [ttyS0] enabled
[ 2.126491@0] console [ttyS0] enabled
[ 2.133866@0] bootconsole [earlycon0] disabled
[ 2.133866@0] bootconsole [earlycon0] disabled
[ 2.142919@0] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff80000fe4c0
[ 2.149549@0] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
[ 2.159357@3] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff]
[ 2.168772@3] meson-gpu-clkgen: probe of c883c000.gpu_clk failed with error -16
[ 2.176285@2] hdmitx: system: hdmitx_hdcp_init
[ 2.180558@2] ESM HLD: Initializing...
[ 2.184117@2] ESM HLD: Registering device range 'esm'...
[ 2.189366@2] ESM HLD: Device range 'esm' has been registered.
[ 2.195145@2] ESM HLD: Creating class /sys/class/elliptic...
[ 2.200859@3] ESM HLD: The class /sys/class/elliptic has been created.
[ 2.207224@3] ESM HLD: Creating device 'esm'...
[ 2.211834@3] ESM HLD: Device 'esm' has been created.
[ 2.216717@3] ESM HLD: Done initializing the HLD driver.
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[ 2.237929@2] aml_vrtc rtc.32: rtc core: registered aml_vrtc as rtc0
[ 2.239327@3] secmon has 1 memory regions
[ 2.242639@3] secmon: share in base: 0xffffff800011a000, share out base: 0xffffff800011c000
[ 2.250900@3] secmon secmon.4: assigned reserved memory node linux,secmon ok
[ 2.257874@3] secmon: probe done
[ 2.261390@3] storage: storage in base: 0xffffff8001800000
[ 2.266510@3] storage: storage out base: 0xffffff8001880000
[ 2.272013@3] storage: storage block base: 0xffffff8001900000
[ 2.277711@3] storage: probe done!
[ 2.281594@2] aml_sd_emmc_probe: line 3578
[ 2.285154@2] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
[ 2.295039@2] aml_sd_emmc_reg_init 1146
[ 2.298370@2] get property: ocr_avail, value:0x00200080
[ 2.304813@2] get property: f_min, value:300000
[ 2.310912@2] get property: f_max, value:100000000
[ 2.317301@2] get property: max_req_size, value:0x00020000
[ 2.323773@2] get property: pinname, str:emmc
[ 2.329543@2] get property: card_type, value:1
[ 2.335256@2] get property: gpio_dat3, str:
[ 2.340669@2] get property: hw_reset, str:
[ 2.346138@2] emmc:pdata->caps = c0000d47
[ 2.350073@2] emmc:pdata->caps2 = 18060
[ 2.353880@2] storage 1, boot 1
[ 2.356969@2] get_storage_dev return 1
[ 2.393431@3] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.393642@3] aml_sd_emmc_probe: line 3578
[ 2.398051@3] aml_sd_emmc_reg_init 1146
[ 2.401516@3] get property: ocr_avail, value:0x00200080
[ 2.407950@3] get property: f_min, value:400000
[ 2.414065@3] get property: f_max, value:100000000
[ 2.420441@3] get property: max_req_size, value:0x00020000
[ 2.426915@3] get property: irq_in, value:3
[ 2.432602@3] get property: irq_out, value:5
[ 2.438308@3] get property: gpio_cd, str:
[ 2.443734@3] get property: pinname, str:sd
[ 2.449336@3] get property: jtag_pin, str:
[ 2.454776@3] get property: card_type, value:5
[ 2.460462@3] get property: gpio_dat3, str:
[ 2.465912@3] sd:pdata->caps = 7
[ 2.469085@3] sd:pdata->caps2 = 0
[ 2.503614@2] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.503649@4] [aml_is_card_insert] card OUT
[ 2.503725@5] [aml_is_card_insert] card OUT
[ 2.512114@2] aml_sd_emmc_probe: line 3578
[ 2.516517@2] aml_sd_emmc_reg_init 1146
[ 2.519986@2] get property: ocr_avail, value:0x00200080
[ 2.526409@2] get property: f_min, value:400000
[ 2.532523@2] get property: f_max, value:200000000
[ 2.538911@2] get property: max_req_size, value:0x00020000
[ 2.545383@2] get property: pinname, str:sdio
[ 2.551154@2] get property: card_type, value:3
[ 2.556889@2] sdio:pdata->caps = 7810f
[ 2.560553@2] sdio:pdata->caps2 = 0
[ 2.580165@1] emmc: BKOPS_EN bit is not set
[ 2.589329@1] emmc: trying cali 0-th time(s)
[ 2.592299@1] emmc: delay[0]= 4600 padding= 2, bidx=4
[ 2.592966@1] emmc: delay[1]= 4600 padding= 2, bidx=4
[ 2.597984@1] emmc: delay[2]= 4400 padding= 3, bidx=4
[ 2.602971@1] emmc: delay[3]= 4800 padding= 1, bidx=4
[ 2.607995@1] emmc: delay[4]= 4800 padding= 1, bidx=4
[ 2.612976@1] emmc: delay[5]= 4800 padding= 1, bidx=4
[ 2.613421@2] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 2.613765@2] ion_dev has 1 memory regions
[ 2.627819@1] emmc: delay[6]= 4600 padding= 2, bidx=4
[ 2.629861@2] fb: osd_init_module
[ 2.629986@2] fb: viu vsync irq: 35
[ 2.629993@2] fb: failed to init reserved memory
[ 2.630005@2] fb: osd_probe vinfo:ffffffc002086d98
[ 2.630010@2] fb: init fbdev bpp is:32
[ 2.652581@1] emmc: delay[7]= 4800 padding= 1, bidx=4
[ 2.657589@1] emmc: calibration result @ 0: max(4800), min(4400)
[ 2.663528@1] emmc: line_delay =0x1000211, max_cal_result =4800
[ 2.666721@0] fb: osd probe OK
[ 2.666949@0] ge2d: ge2d_init_module
[ 2.666957@0] ge2d: ge2d_dev major:243
[ 2.667307@0] ge2d: ge2d clock is 400 MHZ
[ 2.667312@0] ge2d: ge2d: pdev=ffffffc06560b600, irq=182, rstc=0xfffeffc065774f80, clk=ffffffc06565c800
[ 2.667366@0] ge2d: mapped phy: 0xd0160000
[ 2.667371@0] ge2d: ge2d start monitor
[ 2.667433@2] ge2d: ge2d workqueue monitor start
[ 2.667625@2] sysled: module init
[ 2.667738@2] sysled: led_gpio = 154
[ 2.667739@2] sysled: active_low = 0
[ 2.667895@0] sysled: module probed ok
[ 2.668283@0] pwmled: module init
[ 2.668372@0] codec:Amlogic A/V streaming port init
[ 2.669695@2] codec:get gate demux control ok ffffffc063ef1b00
[ 2.669699@2] codec:get gate parser_top control ok ffffffc063ef1680
[ 2.669704@2] codec:get gate vpu_intr control ok ffffffc063ef1200
[ 2.669709@2] codec:get gate vdec control ok ffffffc063ef1d80
[ 2.670332@2] codec:[tsync_pcr_init]init success.
[ 2.670334@2] codec:amvideocap_init_module
[ 2.670458@2] codec:amvideocap_probe,amvideocap
[ 2.670462@2] codec:use cma buf.
[ 2.670463@2] codec:amvideocap_dev_register
[ 2.672273@0] amvenc_avc_probe -- reserved memory config fail.
[ 2.672275@0] amvenc_avc - cma memory pool size: 40 MB
[ 2.672296@0] encode_wq_init.
[ 2.672301@0] encode start monitor.
[ 2.672357@2] encode workqueue monitor start.
[ 2.672757@0] jpegenc module init
[ 2.673055@2] codec:picdec_driver_probe called.
[ 2.673058@2] picdec has 1 memory regions
[ 2.673083@2] codec:picdec_driver_probe done.
[ 2.674073@2] codec:create_ge2d_work_queue video task ok
[ 2.674455@0] codec:used fix clk for vdec clk source!
[ 2.674461@0] codec:register clk_set_setting cpu[34]
[ 2.674791@0] vpu_init
[ 2.674965@0] vpu_probe
[ 2.674969@0] HevcEnc reserved memory config fail.
[ 2.674973@0] HevcEnc - cma memory pool size: 64 MB
[ 2.674975@0] HevcEnc - wave420l_irq: 219
[ 2.675017@0] vpu base address get from platform driver physical base addr=0xc8810000, virtual base=0xffffff8000258000
[ 2.675315@0] success to probe vpu device with video memory from cma
[ 2.675471@2] DI: di_module_init ok.
[ 2.675475@2] DI: di_module_init: major 236
[ 2.675678@0] DI: di_probe
[ 2.675798@2] deinterlace has 1 memory regions
[ 2.675833@2] deinterlace deinterlace.26: assigned reserved memory node linux,di ok
[ 2.675853@2] di_irq:78,timerc_irq:38
[ 2.675979@2] rdma_register, rdma_table_addr ffffff800016c000 rdma_table_addr_phy 74848000 reg_buf ffffffc063cae000
[ 2.675982@2] rdma_register success, handle 1 table_size 8192
[ 2.675983@2] DI: di_probe allocate rdma channel 1.
[ 2.675986@2] DI: DI hw version 2.
[ 2.675997@2] 0x000000db:Y=db,U=0,V=0
[ 2.675998@2] 0x000000dc:Y=dc,U=0,V=0
[ 2.676000@2] 0x000000dd:Y=dd,U=0,V=0
[ 2.676002@2] 0x000000de:Y=de,U=0,V=0
[ 2.676004@2] 0x000000df:Y=df,U=0,V=0
[ 2.676005@2] 0x000000e0:Y=e0,U=0,V=0
[ 2.676007@2] 0x000000e1:Y=e1,U=0,V=0
[ 2.676008@2] 0x000000e2:Y=e2,U=0,V=0
[ 2.676010@2] 0x000000e3:Y=e3,U=0,V=0
[ 2.676012@2] 0x000000f0:Y=f0,U=0,V=0
[ 2.676016@2] 0x000000f1:Y=f1,U=0,V=0
[ 2.676018@2] 0x000000f2:Y=f2,U=0,V=0
[ 2.676019@2] 0x000000f3:Y=f3,U=0,V=0
[ 2.676021@2] 0x000000f4:Y=f4,U=0,V=0
[ 2.676023@2] 0x000000f5:Y=f5,U=0,V=0
[ 2.676024@2] 0x000000f6:Y=f6,U=0,V=0
[ 2.676028@2] 0x000000f7:Y=f7,U=0,V=0
[ 2.676030@2] 0x000000f8:Y=f8,U=0,V=0
[ 2.676032@2] 0x000000f9:Y=f9,U=0,V=0
[ 2.676033@2] 0x000000fa:Y=fa,U=0,V=0
[ 2.676035@2] 0x000000fb:Y=fb,U=0,V=0
[ 2.676036@2] 0x000000fc:Y=fc,U=0,V=0
[ 2.676178@2] DI: di_probe here.
[ 2.676517@0] efusekeynum: 4
[ 2.676525@0] efusekeyname: mac offset: 0 size: 6
[ 2.676531@0] efusekeyname: mac_bt offset: 6 size: 6
[ 2.676536@0] efusekeyname: mac_wifi offset: 12 size: 6
[ 2.676541@0] efusekeyname: usid offset: 18 size: 16
[ 2.676768@0] efuse efuse.10: probe OK!
[ 2.677110@2] key unify config unifykey-num is 14
[ 2.677150@2] key unify fact unifykey-num is 14
[ 2.677154@2] aml_unifykeys_probe:1273=============unifykey_devno:ea00000
[ 2.677365@2] 6unifykey: device unifykeys created ok
[ 2.677477@0] 6aml_unifykeys_init done!
[ 2.677479@0] PPMGRDRV: warn: ppmgr module init func called
[ 2.677606@0] PPMGRDRV: err: ppmgr_driver_probe called
[ 2.677609@0] ppmgr has 1 memory regions
[ 2.677639@0] PPMGRDRV: info: ppmgr_dev major:233
[ 2.677852@0] PPMGRDRV: info: ppmgr_probe done
[ 2.678235@0] amlogic rfkill init
[ 2.678331@0] enter bt_probe of_node
[ 2.678350@0] not get gpio_en
[ 2.678631@0] power on valid level is high
[ 2.678631@0] Bluetooth: BlueSleep Mode Driver Ver 1.2
[ 2.679053@2] ionvideo-000: V4L2 device registered as video13
[ 2.679055@2] ionvid: info: Video Technology Magazine Ion Video
[ 2.679057@2] ionvid: info: Capture Board ver 1.0 successfully loaded
[ 2.679064@2] audio_dsp: [dsp]register dsp to char divece(257)
[ 2.679676@0] amaudio: amaudio: driver amaudio succuess!
[ 2.679956@2] amlvid:err: amlvideo_init called
[ 2.679957@2] amlvid:err: amlvideo_create_instance called
[ 2.679959@2] amlvid:err: v4l2_dev.name=:amlvideo-000
[ 2.680078@0] amlvideo-000: V4L2 device registered as video10
[ 2.680397@0] vdin_drv_init: major 232
[ 2.680693@0] vdin_drv_init: vdin driver init done
[ 2.680697@0] tvafe_drv_init: major 231
[ 2.680975@0] tvafe: tvafe_init.
[ 2.681243@0] [RX]-hdmirx: hdmirx_init.
[ 2.681246@0] ESM HLD: Initializing...
[ 2.681248@0] ESM HLD: Registering device range 'esm_rx'...
[ 2.681254@0] ESM HLD: Device range 'esm_rx' has been registered.
[ 2.681255@0] ESM HLD: Creating class /sys/class/elliptic_rx...
[ 2.681323@2] ESM HLD: The class /sys/class/elliptic_rx has been created.
[ 2.681324@2] ESM HLD: Creating device 'esm_rx'...
[ 2.681434@0] ESM HLD: Device 'esm_rx' has been created.
[ 2.681436@0] ESM HLD: Done initializing the HLD driver.
[ 2.681438@0] [viuin..]viuin_init_module viuin module init
[ 2.681828@0] [viuin..]viuin_probe probe ok.
[ 2.681902@2] module init
[ 2.682028@2]
[ 2.682028@2] VECM probe start
[ 2.682286@2] aml_vecm_probe: ok
[ 2.682880@0] saradc c1108680.saradc: initialized by BL30
[ 2.682891@0] saradc c1108680.saradc: calibration start:
[ 2.682936@0] saradc c1108680.saradc: nominal=0, value=7
[ 2.682981@0] saradc c1108680.saradc: nominal=256, value=251
[ 2.683026@0] saradc c1108680.saradc: nominal=512, value=499
[ 2.683070@0] saradc c1108680.saradc: nominal=768, value=748
[ 2.683113@0] saradc c1108680.saradc: nominal=1023, value=997
[ 2.683116@0] saradc c1108680.saradc: calibration end: coef=4219
[ 2.683285@2] remote: Driver init
[ 2.683360@2] remote: platform_data g_remote_ao_offset=580
[ 2.683362@2] remote: platform_data irq =228
[ 2.683387@2] remote: set drvdata completed
[ 2.683398@2] remote: device_create_file completed
[ 2.683738@2] input: aml_keypad as /devices/meson-remote.12/input/input0
[ 2.684012@2] remote: input_register_device completed
[ 2.684067@2] remote: set_remote_mode[74]
[ 2.684093@2] remote: remote config major:228
[ 2.684272@2] remote: physical address:0x63b82000
[ 2.684852@2] gpio-key gpio_keypad.48: gpio_key: 0 name(power) pin()
[ 2.684857@2] gpio-key gpio_keypad.48: amlogic_gpio_name_map_num pin 0!::
[ 2.684876@2] gpio-key gpio_keypad.48: gpio_key: 0 power(147)
[ 2.684908@2] gpio-key gpio_keypad.48: start setup_timer
[ 2.684915@2] gpio-key gpio_keypad.48: power key(116) registed.
[ 2.685102@0] input: gpio_keypad as /devices/gpio_keypad.48/input/input1
[ 2.685223@2] gpio-key gpio_keypad.48: gpio keypad register input device completed.
[ 2.685231@2] input input1: gpio keypad major:227
[ 2.686377@0] Sensor: lsm303d_init
[ 2.686582@2] Sensor: stk8313_init
[ 2.686659@0] Sensor: stk831x_init
[ 2.686729@2] Sensor: mxc622x_acc_init
[ 2.686798@0] Sensor: mxc6255xc_acc_init
[ 2.686933@0] Sensor: l3gd20_gyr_init
[ 2.687867@0] aml dvb init
[ 2.688267@0] Amlogic Demod DVB-T/C DebugIF Init
[ 2.688451@0] Amlogic Demod DVB-T/C DebugIF Init ok----------------
[ 2.689247@0] jtag: module init
[ 2.689432@2] jtag: pinctrl setup apao
[ 2.689434@2] jtag: set state 2
[ 3.083445@2] input input1: key 116 up
[ 3.412467@1] emmc: base_index_max 4, base_index_min 4
[ 3.417535@1] emmc: clk 100000000 SDR mode tuning start
fuse_pw_en: 0x3
WARNING! efuse bits is disabled
Enable A53 JTAG cluster 0 to AO
[ 3.435776@0] jtag: module probed ok
[ 3.436228@1] emmc: rx_tuning_result[0] = 10
[ 3.436234@0] cpuinfo: probe done
[ 3.436590@0] defendkey c8834500.defendkey: defendkey_devno:df00000
[ 3.436815@0] defendkey c8834500.defendkey: defendkey: device defendkey created ok
[ 3.437006@2] defendkey: driver init
[ 3.437673@0] input: cec_input as /devices/virtual/input/input2
[ 3.437903@2] cectx aocec: no hdmirx reg resource
[ 3.437906@2] cectx aocec: no hhi reg resource
[ 3.437999@2] cectx aocec: can't find hdmirx
[ 3.439002@2] cec: wake up flag:0
[ 3.439971@0] aml_aes_dma c883e000.aml_aes: Aml AES_dma
[ 3.440520@2] aml_tdes_dma c883e000.aml_tdes: Aml TDES_dma
[ 3.441144@0] aml_sha_dma c883e000.aml_sha: Aml SHA1/SHA224/SHA256 dma
[ 3.441654@2] usbcore: registered new interface driver snd-usb-audio
[ 3.442992@2] aml_codec_T9015 c8832000.t9015: aml_T9015_audio_codec_probe
[ 3.445186@0] aml_pcm_dai: pcm mode detection =1
[ 3.445544@2] aml_spdif_dai: enterd aml_spdif_play,set_clock:-1,sample_rate=4
[ 3.445562@2] aml_spdif_dai: set normal 512 fs /4 fs
[ 3.445569@2] aml_audio_hw: IEC958 16bit
[ 3.445574@2] hdmitx: audio: aout notify rate 48000
[ 3.445575@2] hdmitx: audio: aout notify size 16
[ 3.445577@2] hdmitx: audio: aout notify format CT_PCM
[ 3.445579@2] hdmtix: set audio
[ 3.445592@2] hdmitx tx_aud_src = 0
[ 3.445619@2] hdmitx: fs = 3, cd = 4, tmds_clk = 148500
[ 3.445621@2] hdmitx aud_n_para = 6144
[ 3.445639@2] hdmitx set channel status
[ 3.445699@2] hdmitx: audio: Audio Type: PCM
[ 3.445701@2] hdmitx: audio: set audio param
[ 3.575840@1] emmc: rx_tuning_result[1] = 10
[ 3.578378@1] emmc: rx_tuning_result[2] = 10
[ 3.582603@1] emmc: rx_tuning_result[3] = 10
[ 3.586844@1] emmc: rx_tuning_result[4] = 10
[ 3.591056@1] emmc: rx_tuning_result[5] = 10
[ 3.595298@1] emmc: rx_tuning_result[6] = 10
[ 3.599509@1] emmc: rx_tuning_result[7] = 10
[ 3.603771@1] emmc: rx_tuning_result[8] = 10
[ 3.607480@1] emmc: best_win_start =0, best_win_size =9
[ 3.612606@1] emmc: sd_emmc_regs->gclock=0x100024a,sd_emmc_regs->gadjust=0x42000
[ 3.619954@1] emmc: gclock =0x100024a, gdelay=0x1000211, gadjust=0x42000
[ 3.626915@1] emmc: new HS200 MMC card at address 0001
[ 3.631667@1] emmc: clock 100000000, 8-bit-bus-width
[ 3.637120@0] mmcblk0: emmc:0001 NCard 14.4 GiB
[ 3.641621@0] mmcblk0boot0: emmc:0001 NCard partition 1 4.00 MiB
[ 3.647736@0] mmcblk0boot1: emmc:0001 NCard partition 2 4.00 MiB
[ 3.653648@2] aml_snd_card: headphone detection disable=1
[ 3.653889@0] mmcblk0rpmb: emmc:0001 NCard partition 3 4.00 MiB
[ 3.654762@1] mmcblk0: unknown partition table
[ 3.655495@0] [mmc_read_partition_tbl] mmc read partition OK!
[ 3.655496@0] add_emmc_partition
[ 3.655666@1] [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
[ 3.655803@0] [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
[ 3.655931@1] [mmcblk0p03] cache offset 0x000006c00000, size 0x000020000000
[ 3.656051@0] [mmcblk0p04] env offset 0x000027400000, size 0x000000800000
[ 3.656168@1] [mmcblk0p05] logo offset 0x000028400000, size 0x000002000000
[ 3.656290@0] [mmcblk0p06] recovery offset 0x00002ac00000, size 0x000002000000
[ 3.656416@1] [mmcblk0p07] rsv offset 0x00002d400000, size 0x000000800000
[ 3.656537@0] [mmcblk0p08] tee offset 0x00002e400000, size 0x000000800000
[ 3.656656@1] [mmcblk0p09] crypt offset 0x00002f400000, size 0x000002000000
[ 3.656775@0] [mmcblk0p10] misc offset 0x000031c00000, size 0x000002000000
[ 3.656899@1] [mmcblk0p11] instaboot offset 0x000034400000, size 0x000020000000
[ 3.657017@0] [mmcblk0p12] boot offset 0x000054c00000, size 0x000002000000
[ 3.657137@1] [mmcblk0p13] system offset 0x000057400000, size 0x000080000000
[ 3.657251@0] [mmcblk0p14] data offset 0x0000d7c00000, size 0x0002c5400000
[ 3.657281@0] card key: card_blk_probe.
[ 3.657285@0] emmc_key_init:527 emmc key lba_start:0x12020,lba_end:0x12220
[ 3.657288@0] emmc key: emmc_key_init:552 ok.
[ 3.657468@0] amlmmc_dtb_init: register dtb chardev
[ 3.657544@1] amlmmc_dtb_init: register dtb chardev OK
[ 3.657545@1] Exit aml_emmc_partition_ops OK.
[ 3.658555@0] mmcblk0boot1: unknown partition table
[ 3.659341@0] mmcblk0boot0: unknown partition table
[ 3.659597@1] clear_emmc_wait_flag
[ 3.838133@2] aml_snd_card: no spk event delay time set
[ 3.843508@2] aml_snd_m8_card aml_m8_snd.47: T9015-audio-hifi <-> I2S.40 mapping ok
[ 3.850997@2] aml_snd_m8_card aml_m8_snd.47: dit-hifi <-> SPDIF.41 mapping ok
[ 3.857698@2] aml_pcm: enter aml_pcm_new dai->name: PCM.42 dai->id: 0
[ 3.864124@2] aml_snd_m8_card aml_m8_snd.47: pcm2bt-pcm <-> PCM.42 mapping ok
[ 3.871029@2] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTL
[ 3.878627@2] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
[ 3.887420@2] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTR
[ 3.895014@2] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
[ 3.905556@3] GACT probability NOT on
[ 3.907419@3] Mirror/redirect action on
[ 3.911205@3] u32 classifier
[ 3.914062@3] Actions configured
[ 3.917589@3] Netfilter messages via NETLINK v0.30.
[ 3.922469@3] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 3.929113@2] ctnetlink v0.93: registering with nfnetlink.
[ 3.934625@2] xt_time: kernel timezone is -0000
[ 3.938626@2] ipip: IPv4 over IPv4 tunneling driver
[ 3.944152@2] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.948934@2] arp_tables: (C) 2002 David S. Miller
[ 3.953670@2] TCP: cubic registered
[ 3.957001@2] Initializing XFRM netlink socket
[ 3.962287@2] NET: Registered protocol family 10
[ 3.967163@3] mip6: Mobile IPv6
[ 3.969099@3] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.974919@3] sit: IPv6 over IPv4 tunneling driver
[ 3.980693@2] NET: Registered protocol family 17
[ 3.984051@2] NET: Registered protocol family 15
[ 3.988643@2] Bridge firewalling registered
[ 3.992711@2] Bluetooth: RFCOMM TTY layer initialized
[ 3.997718@2] Bluetooth: RFCOMM socket layer initialized
[ 4.002907@2] Bluetooth: RFCOMM ver 1.11
[ 4.006798@2] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.012201@2] Bluetooth: BNEP filters: protocol multicast
[ 4.017625@2] Bluetooth: BNEP socket layer initialized
[ 4.022638@2] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 4.028698@2] Bluetooth: HIDP socket layer initialized
[ 4.033842@2] l2tp_core: L2TP core driver, V2.0
[ 4.038256@2] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 4.043164@2] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 4.048921@2] l2tp_netlink: L2TP netlink interface
[ 4.053655@2] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 4.059659@2] l2tp_debugfs: L2TP debugfs support
[ 4.064228@2] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 4.070819@2] NET: Registered protocol family 35
[ 4.075441@2] Key type dns_resolver registered
[ 4.081148@2] Registering SWP/SWPB emulation handler
[ 4.085420@2] regulator-dummy: disabling
[ 4.088956@2] aml_vrtc rtc.32: setting system clock to 2015-01-01 00:00:06 UTC (1420070406)
[ 4.099058@2] gxbb_pm: enter meson_pm_probe!
[ 4.101076@2] gxbb_pm: meson_pm_probe done
[ 4.106117@0] cpucore_cooling_register, max_cpu_core_num:4
[ 4.110709@0] cpucore_cooling_register, max_cpu_core_num:4
[ 4.131266@0] aml_istbt_dev_ready NULL
[ 4.131323@ 4.136152@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 4.139499@0] Freeing unused kernel memory: 1260K (ffffffc001eaa000 - ffffffc001fe5000)
[ 4.163589@0] init: init started!
[ 4.165098@0] init: init second stage started!
[ 4.166107@0] init: waitpid failed: No child processes
[ 4.171031@0] init: (Loading properties from /default.prop took 0.00s.)
[ 4.178960@0] init: (Parsing /init.environ.rc took 0.00s.)
[ 4.182968@0] init: (Parsing /init.usb.rc took 0.00s.)
[ 4.188887@0] init: (Parsing init.amlogic.usb.rc took 0.00s.)
[ 4.194001@0] init: (Parsing init.amlogic.usb.rc took 0.00s.)
[ 4.199238@0] init: (Parsing init.amlogic.board.rc took 0.01s.)
[ 4.205216@0] init: could not import file 'init.amlogic.wifi.rc' from '/init.amlogic.rc'
[ 4.213132@0] init: could not import file 'init.mtk.rc' from '/init.amlogic.rc'
[ 4.220479@0] init: (Parsing /init.amlogic.rc took 0.03s.)
[ 4.226200@0] init: (Parsing /init.usb.configfs.rc took 0.00s.)
[ 4.231732@0] init: (Parsing /init.zygote32.rc took 0.00s.)
[ 4.237372@0] init: (Parsing /init.trace.rc took 0.00s.)
[ 4.242448@0] init: (Parsing /init.rc took 0.06s.)
[ 4.247545@0] init: Starting service 'ueventd'...
[ 4.253957@0] ueventd: ueventd started!
[ 4.512750@1] ueventd: CoL 4.515213@5] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 4.539488@5] init: enter do_confirm_formated /dev/block/tee, /tee
[ 4.540045@5] init: blocksize 1024, bytes_per_inode 1024
[ 4.545349@5] init: do_confirm_formated ext4 try mount
[ 4.561111@5] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
[ 4.620621@0] EXT4-fs (mmcblk0p13): mounted filesystem with ordered data mode. Opts: (null)
[ 4.623372@0] fs_mgr: __mount(source=/dev/block/system,target=/system,type=ext4)=0
[ 4.631496@0] EXT4-fs (mmcblk0p14): Ignoring removed nomblk_io_submit option
[ 4.644417@0] EXT4-fs (mmcblk0p14): 2 orphan inodes deleted
[ 4.644453@0] EXT4-fs (mmcblk0p14): recovery complete
[ 4.659123@0] EXT4-fs (mmcblk0p14): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 4.664327@0] fs_mgr: check_fs(): mount(/dev/block/data,/data,ext4)=0: Success
[ 4.715222@5] fs_mgr: check_fs(): unmount(/data) succeeded
[ 4.716073@5] fs_mgr: Running /system/bin/e2fsck on /dev/block/data
[ 4.799365@5] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 4.799365@5]
[ 4.800121@5] e2fsck: /dev/block/data: clean, 6900/727664 files, 223948/2905088 blocks
[ 4.800121@5]
[ 4.810328@5] EXT4-fs (mmcblk0p14): Ignoring removed nomblk_io_submit option
[ 4.821394@5] EXT4-fs (mmcblk0p14): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
[ 4.827850@5] fs_mgr: __mount(source=/dev/block/data,target=/data,type=ext4)=0
[ 4.835598@3] EXT4-fs (mmcblk0p3): Ignoring removed nomblk_io_submit option
[ 4.845673@3] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 4.852488@3] fs_mgr: check_fs(): mount(/dev/block/cache,/cache,ext4)=0: Success
[ 4.894811@3] fs_mgr: check_fs(): unmount(/cache) succeeded
[ 4.894877@3] fs_mgr: Running /system/bin/e2fsck on /dev/block/cache
[ 4.921760@3] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 4.921760@3]
[ 4.922494@3] e2fsck: /dev/block/cache: clean, 20/32768 files, 4230/131072 blocks
[ 4.922494@3]
[ 4.932171@3] EXT4-fs (mmcblk0p3): Ignoring removed nomblk_io_submit option
[ 4.942255@3] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
[ 4.949640@3] fs_mgr: __mount(source=/dev/block/cache,target=/cache,type=ext4)=0
[ 4.957715@3] EXT4-fs (mmcblk0p8): Ignoring removed nomblk_io_submit option
[ 4.966384@3] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 4.974462@3] fs_mgr: check_fs(): mount(/dev/block/tee,/tee,ext4)=0: Success
[ 5.024815@0] fs_mgr: check_fs(): unmount(/tee) succeeded
[ 5.024884@0] fs_mgr: Running /system/bin/e2fsck on /dev/block/tee
[ 5.049610@0] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 5.049610@0]
[ 5.050417@0] e2fsck: /dev/block/tee: clean, 11/8192 files, 3111/8192 blocks
[ 5.050417@0]
[ 5.059600@0] EXT4-fs (mmcblk0p8): Ignoring removed nomblk_io_submit option
[ 5.068496@1] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
[ 5.077077@1] fs_mgr: __mount(source=/dev/block/tee,target=/tee,type=ext4)=0
[ 5.109489@6] Adding 511996k swap on /dev/block/zram0. Priority:-1 extents:1 across:511996k SS
[ 5.150744@7] EXT4-fs (zram0): mounted filesystem with ordered data mode. Opts: (null)
[ 5.155937@5] init: cannot find '/system/bin/tee-supplicant', disabling 'tee_supplicant'
[ 5.176496@5] init: /recovery not specified in fstab
[ 5.182665@0] logd.auditd: start
[ 5.211197@2] init: Failed to reload policy
[ 5.294461@3] dig: dig start!
[ 5.427757@2] mali_kbase: unknown parameter 'mali_debug_level' ignored
[ 5.428648@2] mali_kbase: unknown parameter 'mali_shared_mem_size' ignored
[ 5.438017@2] ftrace: Allocated trace_printk buffers
[ 5.442797@2] mali d00c0000.t82x: Continuing without Mali regulator control
[ 5.447376@2] mali d00c0000.t82x: set min pp to default 1
[ 5.452622@2] mali d00c0000.t82x: set min clk default to 0
[ 5.458167@2] mali d00c0000.t82x: dvfs table is 5
[ 5.462713@2] mali d00c0000.t82x: dvfs table addr ffffffc0636dbc18, ele size=48
[ 5.469979@2] mali d00c0000.t82x: max clk set 3
[ 5.474482@2] mali d00c0000.t82x: turbo clk set to 4
[ 5.479358@2] mali d00c0000.t82x: default clk set to 1
[ 5.484536@2] mali_plat=ffffffbffc043568
[ 5.488732@2] gpu cooling register okay with err=0
[ 5.493240@2] gpu core cooling register okay with err=0
[ 5.498496@2] gpu_power_main, 63
[ 5.501581@2] hrtimer: interrupt took 11875 ns
[ 5.506049@0] mali d00c0000.t82x: GPU identified as 0x0820 r1p0 status 0
[ 5.513393@0] mali d00c0000.t82x: Probed as mali0
[ 5.523977@0] random: init urandom read with 72 bits of entropy available
[ 5.552660@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 5.554513@2] binder: 3754:3754 transaction failed 29189, size 0-0
[ 5.558743@2] amlkey_init() enter!
[ 5.569996@2] logd.daemon: reinit
[ 5.589036@3] emmc_key_read:428, read ok
[ 5.589076@3] amlkey_init() storagekey_info.buffer=ffffff8001900000, storagekey_info.size = 40000!
[ 5.593281@2] warning: `daemonsu' uses 32-bit capabilities (legacy support in use)
[ 5.605069@3] vfm_map_store:rm default
[ 5.607512@3] vfm_map_store:add default decoder ppmgr deinterlace amvideo
[ 5.614413@3] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
[ 5.623856@3] init: cannot expand '${ro.usb.vendor.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/vendor_string'
[ 5.636334@3] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
[ 5.646136@3] init: cannot expand '${ro.usb.product.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/product_string'
[ 5.658808@3] init: property_set("ro.radio.noril", "true" failed
[ 5.666135@3] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
[ 5.674332@3] init: cannot expand '${ro.usb.vendor.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/vendor_string'
[ 5.680834@0] vout_serve: vmode set to 1080p60hz
[ 5.680837@0] vout_serve: don't set the same mode as current
[ 5.696947@3] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
[ 5.706732@3] init: cannot expand '${ro.usb.product.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/product_string'
[ 5.721343@3] init: cannot find '/system/bin/debuggerd64', disabling 'debuggerd64'
[ 5.726893@3] init: cannot find '/system/bin/rild', disabling 'ril-daemon'
[ 5.735462@3] init: cannot find '/system/bin/install-recovery.sh', disabling 'flash_recovery'
[ 5.744516@1] fb: afbc: 1
[ 5.744701@1] fb: use ion buffer for fb memory
[ 5.747250@3] init: cannot find '/system/xbin/perfprofd', disabling 'perfprofd'
[ 5.747332@3] init: cannot find '/system/bin/tee-supplicant', disabling 'tee_supplicant'
ro[ 5.764524@1] fb: OSD0 as afbcd mode
[ 5.765979@7] remote: cur_mode = 0
[ 5.765986@7] remote: set_remote_mode[74]
[ 5.767707@7] remote: cur_mode = 0
[ 5.767713@7] remote: set_remote_mode[74]
[ 5.782964@1] meson-fb meson-fb.16: create ion_client ffffffc063b3b900, handle=ffffffc063205dc0
[ 5.791384@1] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 8 MiB
[ 5.800008@1] fb: 0, phy: 0x0000000079300000, vir:0xffffff8002f7f000, size=8300K
[ 5.800008@1]
[ 5.809264@1] meson-fb meson-fb.16: create ion_client ffffffc063b3b900, handle=ffffffc063205f80
[ 5.817679@1] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079b1b000, size 8 MiB
[ 5.826305@1] fb: 0, phy: 0x0000000079b1b000, vir:0xffffff800379b000, size=8300K
[ 5.826305@1]
[ 5.835512@1] meson-fb meson-fb.16: create ion_client ffffffc063b3b900, handle=ffffffc063205e40
[ 5.843965@1] meson-fb meson-fb.16: ion memory(0): created fb at 0x000000007a336000, size 8 MiB
[ 5.852565@1] fb: 0, phy: 0x000000007a336000, vir:0xffffff8003fb7000, size=8300K
[ 5.852565@1]
[ 5.861623@1] fb: Frame buffer memory assigned at
[ 5.866112@1] fb: 0, phy: 0x0000000079300000, vir:0xffffff8002f7f000, size=8300K
[ 5.866112@1]
[ 5.875331@1] fb: 0, phy: 0x0000000079300000, vir:0xffffff8002f7f000, size=8300K
[ 5.875331@1]
[ 5.884399@1] fb: 0, phy: 0x0000000079b1b000, vir:0xffffff800379b000, size=8300K
[ 5.884399@1]
[ 5.893441@1] fb: 0, phy: 0x000000007a336000, vir:0xffffff8003fb7000, size=8300K
[ 5.893441@1]
[ 5.902493@1] fb: ---------------clear fb0 memory ffffff8002f7f000
[ 5.910228@1] fb: ---------------clear fb0 memory ffffff800379b000
[ 5.916407@1] fb: ---------------clear fb0 memory ffffff8003fb7000
[ 5.922530@1] fb: osd[0] canvas.idx =0x40
[ 5.924857@1] fb: osd[0] canvas.addr=0x79300000
[ 5.929315@1] fb: osd[0] canvas.width=7680
[ 5.933369@1] fb: osd[0] canvas.height=3240
[ 5.937526@1] fb: osd[0] frame.width=1920
[ 5.941476@1] fb: osd[0] frame.height=1080
ot@q201_9377:/ # Hello Jten!!!
Hello Jten!!!
Hello Jten!!!
[ 6.078533@4] fb: afbc: 1
[ 6.079222@4] fb: use ion buffer for fb memory
[ 6.080053@4] meson-fb meson-fb.16: create ion_client ffffffc063b3b900, handle=ffffffc061127900
[ 6.088667@4] meson-fb meson-fb.16: ion memory(1): created fb at 0x000000007ab51000, size 1 MiB
[ 6.097246@4] fb: Frame buffer memory assigned at[ 6.097333@7] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 6.107393@2] fb: 1, phy: 0x000000007ab51000, vir:0xffffff80049ff000, size=1024K
[ 6.107393@2]
[ 6.116588@2] fb: fb1 open, logo index:1
[ 6.154517@3] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 6.283602@6] fb: osd[1] enable: 0 scale:0x0 (systemcontrol)
[ 6.283644@6] fb: osd[0] enable: 1 scale:0x10001 (systemcontrol)
[ 6.297670@4] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 6.300077@6] fb: free_scale_switch to fb0, mode: 0x10001
[ 6.303370@6] vout_serve: osd0=> x:0,y:0,w:1920,h:1080
[ 6.303370@6] osd1=> x:0,y:0,w:18,h:18
[ 6.312091@6] fb: current vmode=1080p60hz
[ 6.316976@6] fb: osd[1] set scale, h_scale: ENABLE, v_scale: ENABLE
[ 6.322114@6] fb: osd[1].scaledata: 1920 1920 1080 1080
[ 6.327310@6] fb: osd[1].pandata: 0 0 0 0
[ 6.405803@0] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
[ 6.555854@4] healthd: No charger supplies found
[ 6.555908@4] healthd: No battery devices found
[ 8.633875@0] random: nonblocking pool is initialized
[ 10.752134@1] request_suspend_state: wakeup (3->0) at 10668697587 (2015-01-01 00:00:13.163168503 UTC)
[ 10.755717@1] request_suspend_state,168,old_sleep=0,new_state=0
[ 11.690257@5] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 11.690890@5] audio_dsp: last mode 0,now 0
[ 11.695099@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 11.701171@1] audio_dsp: last mode 0,now 0
[ 11.706325@6] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 11.711418@6] audio_dsp: last mode 0,now 0
[ 11.715644@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 11.721678@3] audio_dsp: last mode 0,now 0
[ 11.742730@6] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 11.743364@6] audio_dsp: last mode 0,now 0
[ 11.747534@6] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 11.753642@6] audio_dsp: last mode 0,now 0
[ 11.758285@5] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 11.763989@5] audio_dsp: last mode 0,now 0
[ 11.768095@5] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 11.774212@1] audio_dsp: last mode 0,now 0
[ 11.959893@1] tv_vout: vout [tv_set_vframe_rate_end_hint] return mode = 16, policy = 1!
[ 18.193344@4] avc open
[ 18.193379@4] amvenc_avc check CMA pool sucess, max instance: 2.
[ 18.196212@4] allocating phys 0x75200000, size 20480k, wq:ffffffc061137400.
[ 18.203045@4] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc061137400.
[ 18.213124@4] avc release, wq:ffffffc061137400
[ 18.217479@1] remove encode_work_queue ffffffc061137400 sucess, _destroy_encode_work_queue line 4285.
[ 18.228966@1] ionvid: info: ionvideo open
[ 18.423472@1] ionvid: info: ionvideo_stop_generating!!!!
[ 18.423535@1] ionvid: info: ionvideo release
[ 18.429929@5] ionvid: info: ionvideo open
[ 18.623495@5] ionvid: info: ionvideo_stop_generating!!!!
[ 18.623553@5] ionvid: info: ionvideo release
[ 18.629801@6] ionvid: info: ionvideo open
��r������}�ѽ�}����Ʌѥ���!!!
[ 18.823528@6] ionvid: info:�ionvideo release
[ 18.829945@6] ionvid: info: ionvideo open
[ 19.023465@6] ionvid: info: ionvideo_stop_generating!!!!
[ 19.023530@6] ionvid: info: ionvideo release
[ 19.029774@6] ionvid: info: ionvideo open
[ 19.223475@6] ionvid: info: ionvideo_stop_generating!!!!
[ 19.223548@6] ionvid: info: ionvideo release
[ 19.230859@6] ionvid: info: ionvideo open
[ 19.423494@6] ionvid: info: ionvideo_stop_generating!!!!
[ 19.423563@6] ionvid: info: ionvideo release
[ 19.430754@5] ionvid: info: ionvideo open
[ 19.623474@5] ionvid: info: ionvideo_stop_generating!!!!
[ 19.623540@5] ionvid: info: ionvideo release
[ 19.630283@5] ionvid: info: ionvideo open
[ 19.823531@6] ionvid: info: ionvideo_stop_generating!!!!
[ 19.823625@6] ionvid: info: ionvideo release
[ 19.830186@7] ionvid: info: ionvideo open
[ 20.023459@4] ionvid: info: ionvideo_stop_generating!!!!
[ 20.023541@4] ionvid: info: ionvideo release
[ 20.034310@7] ionvid: info: ionvideo open
[ 18.341123@5] FAT-fs (mmcblk1p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 18.743103@7] avc open
[ 18.743138@7] amvenc_avc check CMA pool sucess, max instance: 2.
[ 18.745914@7] allocating phys 0x75200000, size 20480k, wq:ffffffc041431400.
[ 18.752912@7] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc041431400.
[ 18.763253@3] avc release, wq:ffffffc041431400
[ 18.767717@3] remove encode_work_queue ffffffc041431400 sucess, _destroy_encode_work_queue line 4285.
[ 18.779137@3] ionvid: info: ionvideo open
[ 18.977196@0] ionvid: info: ionvideo_stop_generating!!!!
[ 18.977269@0] ionvid: info: ionvideo release
[ 18.983973@6] ionvid: info: ionvideo open
[ 19.177208@6] ionvid: info: ionvideo_stop_generating!!!!
[ 19.177273@6] ionvid: info: ionvideo release
[ 19.183589@7] ionvid: info: ionvideo open
[ 19.377203@7] ionvid: info: ionvideo_stop_generating!!!!
[ 19.377276@7] ionvid: info: ionvideo release
[ 19.383821@4] ionvid: info: ionvideo open
[ 19.577207@4] ionvid: info: ionvideo_stop_generating!!!!
[ 19.577276@4] ionvid: info: ionvideo release
[ 19.583505@5] ionvid: info: ionvideo open
[ 19.777621@5] ionvid: info: ionvideo_stop_generating!!!!
[ 19.777703@5] ionvid: info: ionvideo release
[ 19.786456@5] ionvid: info: ionvideo open
[ 19.977205@5] ionvid: info: ionvideo_stop_generating!!!!
[ 19.977267@5] ionvid: info: ionvideo release
[ 19.983664@5] ionvid: info: ionvideo open
[ 20.177205@5] ionvid: info: ionvideo_stop_generating!!!!
[ 20.177265@5] ionvid: info: ionvideo release
[ 20.183571@5] ionvid: info: ionvideo open
[ 20.377199@6] ionvid: info: ionvideo_stop_generating!!!!
[ 20.377262@6] ionvid: info: ionvideo release
[ 20.384084@6] ionvid: info: ionvideo open
[ 20.577230@6] ionvid: info: ionvideo_stop_generating!!!!
[ 20.577293@6] ionvid: info: ionvideo release
[ 20.586361@4] ionvid: info: ionvideo open
[ 20.777206@4] ionvid: info: ionvideo_stop_generating!!!!
[ 20.777270@4] ionvid: info: ionvideo release
[ 20.917464@5] libphy: stmmac-0:00 - Link is Up - 100/Full
[ 21.044814@6] avc open
[ 21.044864@6] allocating phys 0x75200000, size 20480k, wq:ffffffc037265400.
[ 21.048584@6] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc037265400.
[ 21.058748@0] avc release, wq:ffffffc037265400
[ 21.062811@0] remove encode_work_queue ffffffc037265400 sucess, _destroy_encode_work_queue line 4285.
[ 21.323906@3] avc open
[ 21.323954@3] allocating phys 0x75200000, size 20480k, wq:ffffffc03a99dc00.
[ 21.327584@3] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc03a99dc00.
[ 21.337615@3] avc release, wq:ffffffc03a99dc00
[ 21.341880@3] remove encode_work_queue ffffffc03a99dc00 sucess, _destroy_encode_work_queue line 4285.
[ 21.633228@1] avc open
[ 21.633273@1] allocating phys 0x75200000, size 20480k, wq:ffffffc0631f6000.
[ 21.636879@1] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc0631f6000.
[ 21.646924@1] avc release, wq:ffffffc0631f6000
[ 21.651258@1] remove encode_work_queue ffffffc0631f6000 sucess, _destroy_encode_work_queue line 4285.
[ 21.943385@2] avc open
[ 21.943427@2] allocating phys 0x75200000, size 20480k, wq:ffffffc0630c0800.
[ 21.947033@2] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc0630c0800.
[ 21.957092@2] avc release, wq:ffffffc0630c0800
[ 21.961398@2] remove encode_work_queue ffffffc0630c0800 sucess, _destroy_encode_work_queue line 4285.
[ 22.236337@0] avc open
[ 22.236383@0] allocating phys 0x75200000, size 20480k, wq:ffffffc0611e4800.
[ 22.240056@0] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc0611e4800.
[ 22.250065@0] avc release, wq:ffffffc0611e4800
[ 22.254377@0] remove encode_work_queue ffffffc0611e4800 sucess, _destroy_encode_work_queue line 4285.
[ 22.521025@3] avc open
[ 22.521068@3] allocating phys 0x75200000, size 20480k, wq:ffffffc063338400.
[ 22.524689@3] amvenc_avc memory config sucess, buff start:0x75200000, size is 0x1400000, wq:ffffffc063338400.
[ 22.534746@3] avc release, wq:ffffffc063338400
[ 22.539040@3] remove encode_work_queue ffffffc063338400 sucess, _destroy_encode_work_queue line 4285.
[ 22.773015@0] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 22.773640@0] audio_dsp: last mode 0,now 0
[ 22.777896@0] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 22.783965@0] audio_dsp: last mode 0,now 0
[ 22.788156@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 22.794177@1] audio_dsp: last mode 0,now 0
[ 22.798319@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 22.804437@1] audio_dsp: last mode 0,now 0
[ 22.810851@5] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 22.814696@5] audio_dsp: last mode 0,now 0
[ 22.819235@5] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 22.824966@5] audio_dsp: last mode 0,now 0
[ 22.830674@0] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 22.835243@0] audio_dsp: last mode 0,now 0
[ 22.839406@0] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 22.845498@0] audio_dsp: last mode 0,now 0
[ 22.861287@7] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 22.861926@7] audio_dsp: last mode 0,now 0
[ 22.866443@6] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 22.872342@6] audio_dsp: last mode 0,now 0
[ 22.878009@6] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 22.882610@6] audio_dsp: last mode 0,now 0
[ 22.886675@6] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 22.892815@3] audio_dsp: last mode 0,now 0
[ 24.702746@7] dig: isBootCompleted:1!
[ 24.703642@7] dig: setDataRoCount count:0!
[ 24.728973@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 24.729029@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 24.738700@1] xhci-hcd xhci-hcd.0.auto: irq 62, io mem 0xc9000000
[ 24.744051@1] hub 1-0:1.0: USB hub found
[ 24.746729@1] hub 1-0:1.0: 3 ports detected
[ 24.751163@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 24.756436@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 24.765226@1] hub 2-0:1.0: USB hub found
[ 24.768165@1] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 24.776919@1] file system registered
[ 24.785025@1] ffs_data_put(): freeing
[ 25.067256@6] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 25.244874@6] hub 1-1:1.0: USB hub found
[ 25.244982@6] hub 1-1:1.0: 3 ports detected
[ 25.527265@4] usb 1-1.2: new low-speed USB device number 3 using xhci-hcd
[ 25.648176@7] usb 1-1.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 25.651697@7] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 25.777373@7] usb 1-1.3: new low-speed USB device number 4 using xhci-hcd
[ 25.880758@7] audio_dsp: drc high cut scale set to 100%
[ 25.881339@7] audio_dsp: drc low boost scale set to 100%
[ 25.888510@6] audio_dsp: drc mode set to LINE
[ 25.888828@7] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 25.921333@7] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0003/input/input3
[ 25.931515@5] hid-generic 0003:046D:C05A.0003: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
root@q201_9377:/ #
root@q201_9377:/ #
root@q201_9377:/ #
root@q201_9377:/ #
root@q201_9377:/ #
root@q201_9377:/ #
root@q201_9377:/ # poweroff
Done
root@q201_9377:/ # [ 30.589318@5] SysRq : Emergency Remount R/O
[ 30.615100@6] EXT4-fs (mmcblk0p14): re-mounted. Opts: (null)
[ 30.624298@6] EXT4-fs (mmcblk0p3): re-mounted. Opts: (null)
[ 30.625717@6] EXT4-fs (mmcblk0p8): re-mounted. Opts: (null)
[ 30.630119@6] EXT4-fs (zram0): re-mounted. Opts: (null)
[ 30.643127@6] Emergency Remount complete
[ 30.699249@6] avmute set to 2
[ 32.011407@3] aml_snd_card: no audio pin_ctrl to shutdown
[ 32.012712@3] sysled: module shutdown ok
[ 32.015547@0] reboot: Power down
INFO: PSCI Affinity Map:
INFO: AffInst: Level 1, MPID 0x0, State ON
INFO: AffInst: Level 1, MPID 0x100, State ON
INFO: AffInst: Level 0, MPID 0x0, State ON
INFO: AffInst: Level 0, MPID 0x1, State ON
INFO: AffInst: Level 0, MPID 0x2, State ON
INFO: AffInst: Level 0, MPID 0x3, State ON
INFO: AffInst: Level 0, MPID 0x100, State ON
INFO: AffInst: Level 0, MPID 0x101, State ON
INFO: AffInst: Level 0, MPID 0x102, State ON
INFO: AffInst: Level 0, MPID 0x103, State ON
bl31 reboot reason: 0x108
bl31 reboot reason: 0x108
system cmd 0.
bl30 get wakeup sources!
process command 00000006
bl30 enter suspend!
cpu clk suspend rate 100000000
suspend_counter: 1
Enter ddr suspend
first time suspend
ddr suspend time: 1885us
store restore gp0 pll
process command 00000001
CEC cfg:0x002f
set vddee to 0x035cmv
089ckern log_addr:0x04
rx stat:00, tx stat:00
ping_cec_ll_tx:TX_ERROR
Set cec log_addr:0x04, ADDR0:14
GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 266905
BL2 Built : 19:58:22, Aug 31 2016.
gxl g54c8aee - xiaobo.gu@droid05
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00015400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a9a00
NOTICE: BL3-1: v1.0(debug):2e39a99
NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
aml log : bl31 normal boot !
[Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
OPS=0x82
fc c2 9 21 fb ca c 14 7e b4 40 63 [0.511357 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gd267f87 (Jan 19 2017 - 16:49:10)
DRAM: 2 GiB
Relocation Offset is: 76ec9000
register usb cfg[0][1] = 0000000077f5f5d8
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073ec96b0
aml_priv->desc_buf = 0x0000000073ecb9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ece270,dt_addr=0000000073ed9270
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000080000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 80000000 1
13: data d7c00000 2c5400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=cold_boot
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 4 vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
rx version is 1.4 or below div=10
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[CANVAS]canvas init
[CANVAS]addr=0x3d851000 width=5760, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
get_cpu_id flag_12bit=1
SARADC open channel(0).
SARADC channel(0) is 0x16 (0x0~0x50).
detect upgrade key
InUsbBurn
noSof
card in
[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading aml_autoscript
533 bytes read in 3 ms (172.9 KiB/s)
## Executing script at 01080000
## defenv_reserve
Saving Environment to aml-storage...
mmc env offset: 0x27400000
Writing to MMC(1)... done
reboot use default mode: normal
INFO: PSCI Affinity Map:
INFO: AffInst: Level 1, MPID 0x0, State ON
INFO: AffInst: Level 1, MPID 0x100, State OFF
INFO: AffInst: Level 0, MPID 0x0, State ON
INFO: AffInst: Level 0, MPID 0x1, State OFF
INFO: AffInst: Level 0, MPID 0x2, State OFF
INFO: AffInst: Level 0, MPID 0x3, State OFF
INFO: AffInst: Level 0, MPID 0x100, State OFF
INFO: AffInst: Level 0, MPID 0x101, State OFF
INFO: AffInst: Level 0, MPID 0x102, State OFF
INFO: AffInst: Level 0, MPID 0x103, State OFF
bl31 reboot reason: 0xd
bl31 reboot reason: 0x1
system cmd 1.
GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 158888
BL2 Built : 19:58:22, Aug 31 2016.
gxl g54c8aee - xiaobo.gu@droid05
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00015400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a9a00
NOTICE: BL3-1: v1.0(debug):2e39a99
NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
aml log : bl31 normal boot !
wdt: reset registers!
[Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
OPS=0x82
fc c2 9 21 fb ca c 14 7e b4 40 63 [0.406689 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gd267f87 (Jan 19 2017 - 16:49:10)
DRAM: 2 GiB
Relocation Offset is: 76ec9000
register usb cfg[0][1] = 0000000077f5f5d8
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073ec96b0
aml_priv->desc_buf = 0x0000000073ecb9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ece270,dt_addr=0000000073ed9270
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000080000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 80000000 1
13: data d7c00000 2c5400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=normal
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 4 vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
rx version is 1.4 or below div=10
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[CANVAS]canvas init
[CANVAS]addr=0x3d851000 width=5760, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
get_cpu_id flag_12bit=1
SARADC open channel(0).
SARADC channel(0) is 0x15 (0x0~0x50).
detect upgrade key
InUsbBurn
noSof
card in
[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading aml_autoscript
533 bytes read in 3 ms (172.9 KiB/s)
## Executing script at 01080000
## defenv_reserve
Saving Environment to aml-storage...
mmc env offset: 0x27400000
Writing to MMC(1)... done
reboot use default mode: normal
INFO: PSCI Affinity Map:
INFO: AffInst: Level 1, MPID 0x0, State ON
INFO: AffInst: Level 1, MPID 0x100, State OFF
INFO: AffInst: Level 0, MPID 0x0, State ON
INFO: AffInst: Level 0, MPID 0x1, State OFF
INFO: AffInst: Level 0, MPID 0x2, State OFF
INFO: AffInst: Level 0, MPID 0x3, State OFF
INFO: AffInst: Level 0, MPID 0x100, State OFF
INFO: AffInst: Level 0, MPID 0x101, State OFF
INFO: AffInst: Level 0, MPID 0x102, State OFF
INFO: AffInst: Level 0, MPID 0x103, State OFF
bl31 reboot reason: 0xd
bl31 reboot reason: 0x1
system cmd 1.
GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 158853
BL2 Built : 19:58:22, Aug 31 2016.
gxl g54c8aee - xiaobo.gu@droid05
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00015400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a9a00
NOTICE: BL3-1: v1.0(debug):2e39a99
NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
aml log : bl31 normal boot !
wdt: reset registers!
[Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
OPS=0x82
fc c2 9 21 fb ca c 14 7e b4 40 63 [0.406654 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gd267f87 (Jan 19 2017 - 16:49:10)
DRAM: 2 GiB
Relocation Offset is: 76ec9000
register usb cfg[0][1] = 0000000077f5f5d8
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073ec96b0
aml_priv->desc_buf = 0x0000000073ecb9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ece270,dt_addr=0000000073ed9270
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000080000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 80000000 1
13: data d7c00000 2c5400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=normal
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 4 vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
rx version is 1.4 or below div=10
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[CANVAS]canvas init
[CANVAS]addr=0x3d851000 width=5760, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
get_cpu_id flag_12bit=1
SARADC open channel(0).
SARADC channel(0) is 0x16 (0x0~0x50).
detect upgrade key
InUsbBurn
noSof
card in
[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading aml_autoscript
533 bytes read in 3 ms (172.9 KiB/s)
## Executing script at 01080000
## defenv_reserve
Saving Environment to aml-storage...
mmc env offset: 0x27400000
Writing to MMC(1)... done
reboot use default mode: normal
INFO: PSCI Affinity Map:
INFO: AffInst: Level 1, MPID 0x0, State ON
INFO: AffInst: Level 1, MPID 0x100, State OFF
INFO: AffInst: Level 0, MPID 0x0, State ON
INFO: AffInst: Level 0, MPID 0x1, State OFF
INFO: AffInst: Level 0, MPID 0x2, State OFF
INFO: AffInst: Level 0, MPID 0x3, State OFF
INFO: AffInst: Level 0, MPID 0x100, State OFF
INFO: AffInst: Level 0, MPID 0x101, State OFF
INFO: AffInst: Level 0, MPID 0x102, State OFF
INFO: AffInst: Level 0, MPID 0x103, State OFF
bl31 reboot reason: 0xd
bl31 reboot reason: 0x1
system cmd 1.
GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 158859
BL2 Built : 19:58:22, Aug 31 2016.
gxl g54c8aee - xiaobo.gu@droid05
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00015400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a9a00
NOTICE: BL3-1: v1.0(debug):2e39a99
NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
aml log : bl31 normal boot !
wdt: reset registers!
[Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
OPS=0x82
fc c2 9 21 fb ca c 14 7e b4 40 63 [0.406672 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gd267f87 (Jan 19 2017 - 16:49:10)
DRAM: 2 GiB
Relocation Offset is: 76ec9000
register usb cfg[0][1] = 0000000077f5f5d8
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073ec96b0
aml_priv->desc_buf = 0x0000000073ecb9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ece270,dt_addr=0000000073ed9270
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000080000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 80000000 1
13: data d7c00000 2c5400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=normal
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 4 vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
rx version is 1.4 or below div=10
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[CANVAS]canvas init
[CANVAS]addr=0x3d851000 width=5760, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
get_cpu_id flag_12bit=1
SARADC open channel(0).
SARADC channel(0) is 0x16 (0x0~0x50).
detect upgrade key
InUsbBurn
noSof
card in
[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading aml_autoscript
533 bytes read in 4 ms (129.9 KiB/s)
## Executing script at 01080000
## defenv_reserve
Saving Environment to aml-storage...
mmc env offset: 0x27400000
Writing to MMC(1)... done
reboot use default mode: normal
INFO: PSCI Affinity Map:
INFO: AffInst: Level 1, MPID 0x0, State ON
INFO: AffInst: Level 1, MPID 0x100, State OFF
INFO: AffInst: Level 0, MPID 0x0, State ON
INFO: AffInst: Level 0, MPID 0x1, State OFF
INFO: AffInst: Level 0, MPID 0x2, State OFF
INFO: AffInst: Level 0, MPID 0x3, State OFF
INFO: AffInst: Level 0, MPID 0x100, State OFF
INFO: AffInst: Level 0, MPID 0x101, State OFF
INFO: AffInst: Level 0, MPID 0x102, State OFF
INFO: AffInst: Level 0, MPID 0x103, State OFF
bl31 reboot reason: 0xd
bl31 reboot reason: 0x1
system cmd 1.
GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 158567
BL2 Built : 19:58:22, Aug 31 2016.
gxl g54c8aee - xiaobo.gu@droid05
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00015400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a9a00
NOTICE: BL3-1: v1.0(debug):2e39a99
NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
aml log : bl31 normal boot !
wdt: reset registers!
[Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
OPS=0x82
fc c2 9 21 fb ca c 14 7e b4 40 63 [0.406357 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gd267f87 (Jan 19 2017 - 16:49:10)
DRAM: 2 GiB
Relocation Offset is: 76ec9000
register usb cfg[0][1] = 0000000077f5f5d8
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073ec96b0
aml_priv->desc_buf = 0x0000000073ecb9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ece270,dt_addr=0000000073ed9270
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000080000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 80000000 1
13: data d7c00000 2c5400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=normal
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 4 vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
rx version is 1.4 or below div=10
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[CANVAS]canvas init
[CANVAS]addr=0x3d851000 width=5760, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
get_cpu_id flag_12bit=1
SARADC open channel(0).
SARADC channel(0) is 0x16 (0x0~0x50).
detect upgrade key
InUsbBurn
noSof
card in
[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading aml_autoscript
533 bytes read in 3 ms (172.9 KiB/s)
## Executing script at 01080000
## defenv_reserve
Saving Environment to aml-storage...
mmc env offset: 0x27400000
Writing to MMC(1)... done
reboot use default mode: normal
INFO: PSCI Affinity Map:
INFO: AffInst: Level 1, MPID 0x0, State ON
INFO: AffInst: Level 1, MPID 0x100, State OFF
INFO: AffInst: Level 0, MPID 0x0, State ON
INFO: AffInst: Level 0, MPID 0x1, State OFF
INFO: AffInst: Level 0, MPID 0x2, State OFF
INFO: AffInst: Level 0, MPID 0x3, State OFF
INFO: AffInst: Level 0, MPID 0x100, State OFF
INFO: AffInst: Level 0, MPID 0x101, State OFF
INFO: AffInst: Level 0, MPID 0x102, State OFF
INFO: AffInst: Level 0, MPID 0x103, State OFF
bl31 reboot reason: 0xd
bl31 reboot reason: 0x1
system cmd 1.
GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 158855
BL2 Built : 19:58:22, Aug 31 2016.
gxl g54c8aee - xiaobo.gu@droid05
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00015400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a9a00
NOTICE: BL3-1: v1.0(debug):2e39a99
NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
aml log : bl31 normal boot !
wdt: reset registers!
[Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
OPS=0x82
fc c2 9 21 fb ca c 14 7e b4 40 63 [0.406654 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gd267f87 (Jan 19 2017 - 16:49:10)
DRAM: 2 GiB
Relocation Offset is: 76ec9000
register usb cfg[0][1] = 0000000077f5f5d8
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073ec96b0
aml_priv->desc_buf = 0x0000000073ecb9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ece270,dt_addr=0000000073ed9270
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000080000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 80000000 1
13: data d7c00000 2c5400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=normal
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 4 vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
rx version is 1.4 or below div=10
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[CANVAS]canvas init
[CANVAS]addr=0x3d851000 width=5760, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
get_cpu_id flag_12bit=1
SARADC open channel(0).
SARADC channel(0) is 0x3c9, Out of range(0x0~0x50)!
saradc - saradc sub-system
Usage:
saradc saradc open <channel> - open a SARADC channel
saradc close - close the SARADC
saradc getval - get the value in current channel
saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
get_cpu_id flag_12bit=1
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
(Re)start USB...
USB0: USB3.0 XHCI init start
Register 3000140 NbrPorts 3
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 4 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
card in
[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading s905_autoscript
871 bytes read in 13 ms (65.4 KiB/s)
## Executing script at 01020000
** Bad device usb 0 **
reading uInitrd
3930724 bytes read in 217 ms (17.3 MiB/s)
reading zImage
16367544 bytes read in 896 ms (17.4 MiB/s)
reading dtb.img
** Unable to read file dtb.img **
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
## Loading init Ramdisk from Legacy Image at 13000000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 3930660 Bytes = 3.7 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
## Flattened Device Tree blob at 01000000
Booting using the fdt blob at 0x1000000
Loading Ramdisk to 73af7000, end 73eb6a24 ... OK
Loading Device Tree to 000000001fff2000, end 000000001ffff1ca ... OK
signature:
fdt_instaboot: no instaboot image
Starting kernel ...
uboot time: 7629319 us
domain-0 init dvfs: 4
domain-1 init dvfs: 4
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-amlogics905x-gac75c6f-dirty (root@user-VirtualBox) (gcc version 4.9.4 20151028 (prerelease) (Linaro GCC 4.9-2016.02) ) #24 SMP PREEMPT Wed Feb 1 12:00:18 MSK 2017
[ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000@0] no prop version_code
[ 0.000000@0] fdt Reserved memory table:
[ 0.000000@0] linux,di: 0x000000007d300000 - 0x000000007f100000 (30 MiB)
[ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007d300000, size 30 MiB
[ 0.000000@0] linux,ion-dev: 0x0000000079300000 - 0x000000007d300000 (64 MiB)
[ 0.000000@0] linux,ppmgr: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] linux,codec_mm_cma: 0x0000000067800000 - 0x0000000073800000 (192 MiB)
[ 0.000000@0] linux,picdec: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] Reserved memory: incorrect alignment of CMA region
[ 0.000000@0] linux,codec_mm_reserved: 0x0000000075200000 - 0x0000000079300000 (65 MiB)
[ 0.000000@0] fdt Reserved memory total: 354 MiB
[ 0.000000@0] cma: Reserved 8 MiB at 74800000
[ 0.000000@0] psci: probing function IDs from device-tree
[ 0.000000@0] PERCPU: Embedded 13 pages/cpu @ffffffc075166000 s20864 r8192 d24192 u53248
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 510280
[ 0.000000@0] Kernel command line: root=LABEL=ROOTFS rootflags=data=writeback rw console=ttyS0,115200n8 console=tty0 no_console_suspend consoleblank=0 fsck.repair=yes net.ifnames=0 mac=86:37:20:48:cb:3e
[ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000@0] Memory: 1641772K/2077696K available (10134K kernel code, 895K rwdata, 3764K rodata, 1180K init, 5772K bss, 435924K reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
[ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff80423cc800 ( 35 MB)
[ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc07f100000 ( 2033 MB)
[ 0.000000@0] .init : 0xffffffc001e14000 - 0xffffffc001f3b180 ( 1181 kB)
[ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001e13a24 ( 13903 kB)
[ 0.000000@0] .data : 0xffffffc001f3c000 - 0xffffffc00201bfb8 ( 896 kB)
[ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01e12fff]
[ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000@0] arch_multi_cluster:1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] RCU debugfs-based tracing is enabled.
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[ 0.000034@0] meson_bc_timer: mclk->mux_reg =ffffff8000014990,mclk->reg =ffffff8000016994
[ 0.000363@0] Console: colour dummy device 80x25
[ 0.000884@0] console [tty0] enabled
[ 0.000905@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.000929@0] pid_max: default: 32768 minimum: 301
[ 0.001042@0] Security Framework initialized
[ 0.001074@0] AppArmor: AppArmor initialized
[ 0.001123@0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.001139@0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.003561@0] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
[ 0.003593@0] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
[ 0.003611@0] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
[ 0.003628@0] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
[ 0.006429@0] Initializing cgroup subsys debug
[ 0.006450@0] Initializing cgroup subsys freezer
[ 0.006495@0] ftrace: allocating 35111 entries in 138 pages
[ 0.050202@0] /cpus/cpu@0: Missing clock-frequency property
[ 0.050235@0] /cpus/cpu@1: Missing clock-frequency property
[ 0.050252@0] /cpus/cpu@2: Missing clock-frequency property
[ 0.050267@0] /cpus/cpu@3: Missing clock-frequency property
[ 0.050284@0] /cpus/cpu@100: Missing clock-frequency property
[ 0.050300@0] /cpus/cpu@101: Missing clock-frequency property
[ 0.050318@0] /cpus/cpu@102: Missing clock-frequency property
[ 0.050337@0] /cpus/cpu@103: Missing clock-frequency property
[ 0.050354@0] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 0.089975@0] Meson chip version = RevA (22:A - 82:0)
[ 0.110082@1] CPU1: Booted secondary processor
[ 0.130081@2] CPU2: Booted secondary processor
[ 0.150081@3] CPU3: Booted secondary processor
[ 0.170108@4] CPU4: Booted secondary processor
[ 0.190109@5] CPU5: Booted secondary processor
[ 0.210125@6] CPU6: Booted secondary processor
[ 0.230137@7] CPU7: Booted secondary processor
[ 0.230223@0] Brought up 8 CPUs
[ 0.230305@0] SMP: Total of 8 processors activated.
[ 0.230846@0] devtmpfs: initialized
[ 0.236090@2] sched: registering cpufreq notifiers for scale-invariant loads
[ 0.236217@2] instabooting: 0
[ 0.242261@2] xor: measuring software checksum speed
[ 0.339925@2] 8regs : 2291.600 MB/sec
[ 0.439954@2] 8regs_prefetch: 2158.800 MB/sec
[ 0.539982@2] 32regs : 2615.200 MB/sec
[ 0.640009@2] 32regs_prefetch: 2364.400 MB/sec
[ 0.640021@2] xor: using function: 32regs (2615.200 MB/sec)
[ 0.640040@2] pinctrl core: initialized pinctrl subsystem
[ 0.640669@2] regulator-dummy: no parameters
[ 0.641425@3] NET: Registered protocol family 16
[ 0.643145@3] cpuidle: using governor menu
[ 0.643378@2] aml_vdac_init: module init
[ 0.643541@0] register canvas platform driver
[ 0.643642@2] register rdma platform driver
[ 0.644356@2] vdso: 2 pages (1 code, 1 data) at base ffffffc001f44000
[ 0.644411@2] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.644788@2] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.645756@2] software IO TLB [mem 0x64400000-0x64800000] (4MB) mapped at [ffffffc064400000-ffffffc0647fffff]
[ 0.646227@2] aml_i2c version: 20140813
[ 0.646476@2] i2c-core: driver [pmu4] using legacy resume method
[ 0.646569@3] codec_mm:codec_mm_module_init
[ 0.646804@2] aml_watch_point_probe, in
[ 0.647236@0] gxbb_mpll_clk: register mpll_clk_out0 success done
[ 0.647257@0] gxbb_mpll_clk: register mpll_clk_out1 success done
[ 0.647273@0] gxbb_mpll_clk: register mpll_clk_out2 success done
[ 0.647479@0] clk_sys: register PLL sys_pll success done
[ 0.647500@0] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
[ 0.647513@0] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
[ 0.647525@0] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
[ 0.647537@0] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
[ 0.647550@0] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
[ 0.647562@0] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
[ 0.647574@0] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
[ 0.647586@0] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
[ 0.647598@0] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
[ 0.647635@0] gxl_clk: clock initialization complete
[ 0.647842@0] clkmsr: Gxl msr_clk_reg0=ffffff800006475c,msr_clk_reg2=ffffff8000066764
[ 0.650367@2] aml_iomap: amlogic iomap probe done
[ 0.651035@3] pinmux-gxl c1109880.pinmux: Init pinux probe!
[ 0.652183@2] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
[ 0.652661@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.652696@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ 0.652867@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.652894@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ 0.659507@3] codec_mm has 2 memory regions
[ 0.659562@3] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.659585@3] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.659696@2] codec_mm has 2 memory regions
[ 0.659721@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.659743@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.661794@2] vpu: driver version: v02
[ 0.661838@2] vpu: load vpu_clk: 666667000Hz(7)
[ 0.661937@3] vpu: vpu_probe OK
[ 0.663510@2] tv_vout: tvout_probe
[ 0.663538@2] tv_vout: major number 254 for disp
[ 0.663550@2] vout_notify: vout_register_server
[ 0.663561@2] tv_vout: register tv module server ok
[ 0.663665@3] tv_vout: tvout_probe OK
[ 0.664309@3] canvas_probe reg=00000000c8838000,size=400
[ 0.664348@3] canvas maped reg_base =ffffff8000188000
[ 0.668176@2] rdma_probe
[ 0.928309@0] bio: create slab <bio-0> at 0
[ 1.090722@0] raid6: int64x1 484 MB/s
[ 1.260761@0] raid6: int64x2 716 MB/s
[ 1.430779@0] raid6: int64x4 1035 MB/s
[ 1.600891@0] raid6: int64x8 1197 MB/s
[ 1.770965@0] raid6: neonx1 771 MB/s
[ 1.941011@0] raid6: neonx2 1201 MB/s
[ 2.111106@0] raid6: neonx4 1563 MB/s
[ 2.281191@0] raid6: neonx8 1723 MB/s
[ 2.281202@0] raid6: using algorithm neonx8 (1723 MB/s)
[ 2.281214@0] raid6: using intx1 recovery algorithm
[ 2.282010@3] SCSI subsystem initialized
[ 2.282528@3] usbcore: registered new interface driver usbfs
[ 2.282639@3] usbcore: registered new interface driver hub
[ 2.282777@0] usbcore: registered new device driver usb
[ 2.283698@3] i2c-gpio i2c_gpio.38: using pins 172 (SDA) and 173 (SCL)
[ 2.283836@3] Linux video capture interface: v2.00
[ 2.284045@3] pps_core: LinuxPPS API ver. 1 registered
[ 2.284060@3] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 2.284136@0] PTP clock support registered
[ 2.284727@3] hdmitx: system: amhdmitx_init
[ 2.284745@3] hdmitx: system: Ver: 2014May6
[ 2.284922@3] hdmitx: system: amhdmitx_probe
[ 2.285265@3] hdmitx: system: not find match init-data
[ 2.285283@3] hdmitx: system: not find match pwr-ctl
[ 2.285296@3] hdmitx hpd irq = 89
[ 2.285751@3] hdmitx20: Mapped PHY: 0xc0800000
[ 2.285776@3] hdmitx20: Mapped PHY: 0xc1104400
[ 2.285802@3] hdmitx20: Mapped PHY: 0xc8100000
[ 2.285814@3] hdmitx20: Mapped PHY: 0xc8834000
[ 2.285826@3] hdmitx20: Mapped PHY: 0xc883a000
[ 2.285837@3] hdmitx20: Mapped PHY: 0xc883c000
[ 2.285851@3] hdmitx20: Mapped PHY: 0xd0100000
[ 2.285863@3] hdmitx20: Mapped PHY: 0xda83a000
[ 2.285880@3] hdmitx: alread display in uboot 0x10
[ 2.285910@3] avmute set to 1
[ 2.286251@1] vout_serve: vout_init_module
[ 2.286390@1] vout_serve: no matched vout_init mode
[ 2.286481@1] vinfo: error: invalid vinfo. current vmode is not supported
[ 2.286495@1] vout_serve: create vout attribute OK
[ 2.286506@1] vout_serve: meson_vout_probe OK
[ 2.286685@3] logo: logo_init
[ 2.286789@3] Advanced Linux Sound Architecture Driver Initialized.
[ 2.287427@0] NetLabel: Initializing
[ 2.287446@0] NetLabel: domain hash size = 128
[ 2.287456@0] NetLabel: protocols = UNLABELED CIPSOv4
[ 2.287504@0] NetLabel: unlabeled traffic allowed by default
[ 2.288540@3] Switched to clocksource arch_sys_counter
[ 2.292974@0] hdmitx: system: irq 80000002
[ 2.301422@3] FS-Cache: Loaded
[ 2.301570@3] AppArmor: AppArmor Filesystem Enabled
[ 2.312010@3] NET: Registered protocol family 2
[ 2.312512@3] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 2.312669@3] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 2.312927@3] TCP: Hash tables configured (established 16384 bind 16384)
[ 2.313000@3] TCP: reno registered
[ 2.313018@3] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 2.313070@3] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 2.313282@3] NET: Registered protocol family 1
[ 2.313542@0] RPC: Registered named UNIX socket transport module.
[ 2.313562@0] RPC: Registered udp transport module.
[ 2.313573@0] RPC: Registered tcp transport module.
[ 2.313583@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.313805@0] aml_wifi wifi.33: [wifi_dev_probe] no power_on_pin2
[ 2.313820@0] aml_wifi wifi.33: [wifi_dev_probe] set pwm as 32k output
[ 2.313879@0] aml_wifi wifi.33: [wifi_dev_probe] interrupt_pin=241
[ 2.313894@0] aml_wifi wifi.33: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
[ 2.313911@0] aml_wifi wifi.33: [wifi_dev_probe] power_on_pin=240
[ 2.313925@0] aml_wifi wifi.33: [wifi_dev_probe] clock_32k_pin=0
[ 2.314281@3] aml_wifi wifi.33: [wifi_setup_dt] wifi_setup_dt
[ 2.314332@3] aml_wifi wifi.33: [wifi_setup_dt] interrupt_pin(241)
[ 2.314355@3] aml_wifi wifi.33: [wifi_setup_dt] power_on_pin(240)
[ 2.314671@3] Unpacking initramfs...
[ 2.472766@3] Freeing initrd memory: 3836K (ffffffc073af7000 - ffffffc073eb6000)
[ 2.475684@3] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 2.475802@3] audit: initializing netlink subsys (disabled)
[ 2.475867@3] audit: type=2000 audit(2.440:1): initialized
[ 2.476788@3] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 2.483885@3] VFS: Disk quotas dquot_6.5.2
[ 2.484150@0] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 2.487247@3] NFS: Registering the id_resolver key type
[ 2.487298@3] Key type id_resolver registered
[ 2.487309@3] Key type id_legacy registered
[ 2.487327@3] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 2.488041@3] msgmni has been set to 3614
[ 2.489384@3] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 2.489416@3] io scheduler noop registered (default)
[ 2.489429@3] io scheduler deadline registered
[ 2.489621@0] io scheduler cfq registered
[ 2.491207@3] meson-rng c8834000.rng: hwrng registered
[ 2.494988@3] loop: module loaded
[ 2.495954@0] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 2.497072@3] tun: Universal TUN/TAP device driver, 1.6
[ 2.497098@3] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 2.618618@3] hdmitx: plugin
[ 2.636664@0] libphy: stmmac: probed
[ 2.636690@0] eth0: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[ 2.636704@0] eth0: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07)
[ 2.637162@0] PPP generic driver version 2.4.2
[ 2.637465@0] NET: Registered protocol family 24
[ 2.637630@1] usbcore: registered new interface driver cdc_ether
[ 2.637749@0] usbcore: registered new interface driver net1080
[ 2.637854@1] usbcore: registered new interface driver cdc_subset
[ 2.637956@0] usbcore: registered new interface driver zaurus
[ 2.638084@1] usbcore: registered new interface driver cdc_ncm
[ 2.638635@1] platform c9000000.dwc3: Driver dwc3 requests probe deferral
[ 2.638829@0] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.638847@0] ehci-h20ahb: H20AHB-EHCI Host Controller driver
[ 2.639108@1] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.639506@1] usbcore: registered new interface driver cdc_acm
[ 2.639524@1] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.639643@0] usbcore: registered new interface driver usb-storage
[ 2.639892@0] usbcore: registered new interface driver usbserial
[ 2.639997@1] usbcore: registered new interface driver usbserial_generic
[ 2.640090@0] usbserial: USB Serial support registered for generic
[ 2.640194@1] usbcore: registered new interface driver pl2303
[ 2.640282@0] usbserial: USB Serial support registered for pl2303
[ 2.640885@0] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff80001be000
[ 2.641135@1] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
[ 2.641170@1] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff80001de080
[ 2.641660@0] mousedev: PS/2 mouse device common for all mice
[ 2.642148@1] usbcore: registered new interface driver xpad
[ 2.642412@1] i2c /dev entries driver
[ 2.642785@0] usbcore: registered new interface driver uvcvideo
[ 2.642804@0] USB Video Class driver (1.1.1)
[ 2.643697@0] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: [email protected]
[ 2.643992@0] CPUidle arm64: cpuidle init start!!
[ 2.644499@1] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.644678@1] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.644945@1] usbcore: registered new interface driver usbhid
[ 2.644960@1] usbhid: USB HID core driver
[ 2.645817@1] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff80001f64c0
[ 2.645861@1] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
[ 2.645892@1] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
[ 2.754764@3] hdmitx: edid: check sum valid
[ 2.754766@3] hdmitx: edid: check sum valid
[ 2.754770@3] hdmitx: edid: blk0 raw data
[ 2.754811@3] 00ffffffffffff001e6de37689bb02000b18010380502278eaca95a6554ea126
[ 2.754811@3] 0f50542108007140818081c0a9c0b300d1c0810001019d6770a0d0a022503020
[ 2.754811@3] 3a00204f3100001a000000fd00383d1e5a1e000a202020202020000000fc004c
[ 2.754811@3] 4720554c545241574944450a000000000000000000000000000000000000017c
[ 2.754811@3]
[ 2.754811@3]
[ 2.754813@3] hdmitx: edid: blk1 raw data
[ 2.754850@3] 020317f14410040301230907078301000065030c0010009f3d70a0d0a0155030
[ 2.754850@3] 203a00204f3100001a7e4800e0a0381f4040403a00204f31000018011d007251
[ 2.754850@3] d01e206e285500204f3100001e8c0ad08a20e02d10103e9600204f3100001800
[ 2.754850@3] 0000ff003431314b4b484e35393038310a0000000000000000000000000000ce
[ 2.754850@3]
[ 2.754850@3]
[ 2.754854@3] EDID Parser:
[ 2.754902@3] hdmitx: edid: find IEEEOUT
[ 2.754906@3] hdmitx: edid: check sum valid
[ 2.754907@3] hdmitx: edid: check sum valid
[ 2.754910@3] vinfo: error: invalid vinfo. current vmode is not supported
[ 2.754912@3] hdmitx: update RX hdr info 0
[ 2.756934@3] hdmitx: ddc rd8b error 0x3a 0x00 0x00
[ 2.758976@3] [RX]-receive ksv list len:1,depth:1,cas:0,dev:0
[ 2.758981@3] vinfo: error: invalid vinfo. current vmode is not supported
[ 2.758983@3] hdmitx: video: get current mode: invalid
[ 2.758984@3] hdmitx: update rx hdr info 0
[ 2.759003@3] hdmitx: edid: not find mapped vic
[ 2.759031@3] hdmitx: system: already init VIC = 0 Now VIC = 0
[ 2.759034@3] hdmitx: system: packet: can't get vendor data
[ 2.759037@3] hdmtix: set audio
[ 2.759045@3] hdmitx tx_aud_src = 0
[ 2.759072@3] hdmitx: fs = 0, cd = 4, tmds_clk = 0
[ 2.759075@3] hdmitx aud_n_para = 6144
[ 2.759093@3] hdmitx set channel status
[ 2.759152@3] hdmtix: set audio
[ 2.759160@3] hdmitx tx_aud_src = 0
[ 2.759185@3] hdmitx: fs = 0, cd = 4, tmds_clk = 0
[ 2.759187@3] hdmitx aud_n_para = 6144
[ 2.759204@3] hdmitx set channel status
[ 4.361876@1] console [ttyS0] enabled
[ 4.365987@1] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff80001f84c0
[ 4.372595@1] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
[ 4.382612@1] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: d0078000, ctrl: 0
[ 4.390520@3] dwc_otg_driver_probe host only, not probe usb_otg!!!
[ 4.396833@3] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff]
[ 4.406575@3] meson-gpu-clkgen: probe of c883c000.gpu_clk failed with error -16
[ 4.414038@3] hdmitx: system: hdmitx_hdcp_init
[ 4.418378@0] ESM HLD: Initializing...
[ 4.421911@0] ESM HLD: Registering device range 'esm'...
[ 4.427162@0] ESM HLD: Device range 'esm' has been registered.
[ 4.432954@0] ESM HLD: Creating class /sys/class/elliptic...
[ 4.438644@3] ESM HLD: The class /sys/class/elliptic has been created.
[ 4.445008@3] ESM HLD: Creating device 'esm'...
[ 4.449722@3] ESM HLD: Device 'esm' has been created.
[ 4.454496@3] ESM HLD: Done initializing the HLD driver.
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[ 4.475801@0] aml_vrtc rtc.32: rtc core: registered aml_vrtc as rtc0
[ 4.477221@0] secmon has 1 memory regions
[ 4.480539@0] secmon: share in base: 0xffffff8000404000, share out base: 0xffffff8000406000
[ 4.488777@0] secmon secmon.4: assigned reserved memory node linux,secmon ok
[ 4.495749@0] secmon: probe done
[ 4.499297@3] storage: storage in base: 0xffffff8001600000
[ 4.504374@3] storage: storage out base: 0xffffff8001680000
[ 4.509904@3] storage: storage block base: 0xffffff8001700000
[ 4.515586@3] storage: probe done!
[ 4.519497@0] aml_sd_emmc_probe: line 3558
[ 4.523007@0] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
[ 4.533071@0] aml_sd_emmc_reg_init 1146
[ 4.536289@0] get property: ocr_avail, value:0x00200080
[ 4.542683@0] get property: f_min, value:300000
[ 4.548812@0] get property: f_max, value:100000000
[ 4.555177@0] get property: max_req_size, value:0x00020000
[ 4.561656@0] get property: pinname, str:emmc
[ 4.567426@0] get property: card_type, value:1
[ 4.573141@0] get property: gpio_dat3, str:
[ 4.578558@0] get property: hw_reset, str:
[ 4.584019@0] emmc:pdata->caps = c0000d47
[ 4.587956@0] emmc:pdata->caps2 = 18060
[ 4.591768@0] storage 1, boot 1
[ 4.594850@0] get_storage_dev return 1
[ 4.638548@0] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 4.638782@0] aml_sd_emmc_probe: line 3558
[ 4.643205@0] aml_sd_emmc_reg_init 1146
[ 4.646760@0] get property: ocr_avail, value:0x00200080
[ 4.653169@0] get property: f_min, value:400000
[ 4.659278@0] get property: f_max, value:100000000
[ 4.665577@0] get property: max_req_size, value:0x00020000
[ 4.672052@0] get property: irq_in, value:3
[ 4.677738@0] get property: irq_out, value:5
[ 4.683521@0] get property: gpio_cd, str:
[ 4.688872@0] get property: pinname, str:sd
[ 4.694471@0] get property: jtag_pin, str:
[ 4.699985@0] get property: card_type, value:5
[ 4.705598@0] get property: gpio_dat3, str:
[ 4.711053@0] sd:pdata->caps = 7
[ 4.714221@0] sd:pdata->caps2 = 0
[ 4.748724@0] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 4.748760@4] [aml_is_card_insert] card IN
[ 4.753015@0] aml_sd_emmc_probe: line 3558
[ 4.757416@0] aml_sd_emmc_reg_init 1146
[ 4.760967@0] get property: ocr_avail, value:0x00200080
[ 4.767299@0] get property: f_min, value:400000
[ 4.773430@0] get property: f_max, value:200000000
[ 4.779885@0] get property: max_req_size, value:0x00020000
[ 4.786278@0] get property: pinname, str:sdio
[ 4.792061@0] get property: card_type, value:3
[ 4.797790@0] sdio:pdata->caps = 7810f
[ 4.801531@0] sdio:pdata->caps2 = 0
[ 4.820458@2] emmc: BKOPS_EN bit is not set
[ 4.829615@2] emmc: trying cali 0-th time(s)
[ 4.832720@2] emmc: delay[0]= 4600 padding= 2, bidx=4
[ 4.833255@2] emmc: delay[1]= 4400 padding= 3, bidx=4
[ 4.838257@2] emmc: delay[2]= 4400 padding= 3, bidx=4
[ 4.838551@1] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 4.838912@0] ion_dev has 1 memory regions
[ 4.850074@4] normal card in
[ 4.855781@0] fb: osd_init_module
[ 4.855912@0] fb: viu vsync irq: 35
[ 4.855918@0] fb: failed to init reserved memory
[ 4.855935@0] tv_vout: tv_set_current_vmode[759]fps_target_mode=16
[ 4.855940@0] tv_vout: mode is 16,sync_duration_den=1,sync_duration_num=60
[ 4.855948@0] tv_vout: TV mode 1080p60hz selected.
[ 4.855953@0]
[ 4.855953@0] vdac_enable: on:0,module_sel:8
[ 4.855958@0]
[ 4.855958@0] vdac_enable: on:0,module_sel:8
[ 4.855964@0] tv_vout: new mode =1080p60hz set ok
[ 4.855966@0] vout_serve: vinfo mode is: 1080p60hz
[ 4.856216@0] osd_rdma: osd_rdma_init: rdma_table p=0x74846000,op=0x74846000 , v=0xffffff800041e000
[ 4.856218@0] osd_rdma: osd rdma request irq as second interrput function!
[ 4.856234@0] fb: osd_probe vinfo:ffffffc001fbd8a8
[ 4.856242@0] fb: init fbdev bpp is:32
[ 4.930298@1] fb: use ion buffer for fb memory
[ 4.930307@2] emmc: delay[3]= 4800 padding= 1, bidx=4
[ 4.930309@2] emmc: delay[4]= 4800 padding= 1, bidx=4
[ 4.930311@2] emmc: delay[5]= 4800 padding= 1, bidx=4
[ 4.930313@2] emmc: delay[6]= 4600 padding= 2, bidx=4
[ 4.930316@2] emmc: delay[7]= 4800 padding= 1, bidx=4
[ 4.930318@2] emmc: calibration result @ 0: max(4800), min(4400)
[ 4.930321@2] emmc: line_delay =0x1000221, max_cal_result =4800
[ 4.930323@2] emmc: base_index_max 4, base_index_min 4
[ 4.930329@2] emmc: clk 100000000 SDR mode tuning start
[ 4.930900@1] meson-fb meson-fb.16: create ion_client ffffffc0640189c0, handle=ffffffc0640a7d40
[ 4.930905@1] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 4.930912@1] fb: Frame buffer memory assigned at
[ 4.930912@1] fb: 0, phy: 0x0000000079300000, vir:0xffffff80018c4000, size=24900K
[ 4.930912@1]
[ 4.930915@1] fb: ---------------clear fb0 memory ffffff80018c4000
[ 4.931059@2] emmc: rx_tuning_result[0] = 10
[ 4.931573@2] emmc: rx_tuning_result[1] = 10
[ 4.932084@2] emmc: rx_tuning_result[2] = 10
[ 4.932596@2] emmc: rx_tuning_result[3] = 10
[ 4.933114@2] emmc: rx_tuning_result[4] = 10
[ 4.933631@2] emmc: rx_tuning_result[5] = 10
[ 4.934134@2] emmc: rx_tuning_result[6] = 10
[ 4.934642@2] emmc: rx_tuning_result[7] = 10
[ 4.935153@2] emmc: rx_tuning_result[8] = 10
[ 4.935206@2] emmc: best_win_start =0, best_win_size =9
[ 4.935209@2] emmc: sd_emmc_regs->gclock=0x100024a,sd_emmc_regs->gadjust=0x42000
[ 4.935213@2] emmc: gclock =0x100024a, gdelay=0x1000221, gadjust=0x42000
[ 4.935538@2] emmc: new HS200 MMC card at address 0001
[ 4.936035@0] emmc: clock 100000000, 8-bit-bus-width
[ 4.936035@0]
[ 4.936035@0] mmcblk0: emmc:0001 NCard 14.4 GiB
[ 4.936177@0] mmcblk0boot0: emmc:0001 NCard partition 1 4.00 MiB
[ 4.936308@0] mmcblk0boot1: emmc:0001 NCard partition 2 4.00 MiB
[ 4.936437@0] mmcblk0rpmb: emmc:0001 NCard partition 3 4.00 MiB
[ 4.937202@2] mmcblk0: unknown partition table
[ 4.937934@0] [mmc_read_partition_tbl] mmc read partition OK!
[ 4.937935@0] add_emmc_partition
[ 4.938191@2] [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
[ 4.938379@0] [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
[ 4.938586@2] [mmcblk0p03] cache offset 0x000006c00000, size 0x000020000000
[ 4.938781@0] [mmcblk0p04] env offset 0x000027400000, size 0x000000800000
[ 4.938959@2] [mmcblk0p05] logo offset 0x000028400000, size 0x000002000000
[ 4.939137@0] [mmcblk0p06] recovery offset 0x00002ac00000, size 0x000002000000
[ 4.939312@2] [mmcblk0p07] rsv offset 0x00002d400000, size 0x000000800000
[ 4.939483@0] [mmcblk0p08] tee offset 0x00002e400000, size 0x000000800000
[ 4.939654@2] [mmcblk0p09] crypt offset 0x00002f400000, size 0x000002000000
[ 4.939833@0] [mmcblk0p10] misc offset 0x000031c00000, size 0x000002000000
[ 4.940008@2] [mmcblk0p11] instaboot offset 0x000034400000, size 0x000020000000
[ 4.940177@0] [mmcblk0p12] boot offset 0x000054c00000, size 0x000002000000
[ 4.940348@2] [mmcblk0p13] system offset 0x000057400000, size 0x000080000000
[ 4.940517@0] [mmcblk0p14] data offset 0x0000d7c00000, size 0x0002c5400000
[ 4.940548@0] card key: card_blk_probe.
[ 4.940552@0] emmc_key_init:527 emmc key lba_start:0x12020,lba_end:0x12220
[ 4.940555@0] emmc key: emmc_key_init:552 ok.
[ 4.940803@0] amlmmc_dtb_init: register dtb chardev
[ 4.940889@2] amlmmc_dtb_init: register dtb chardev OK
[ 4.940889@2] Exit aml_emmc_partition_ops OK.
[ 4.942048@1] fb: osd[0] canvas.idx =0x40
[ 4.942050@1] fb: osd[0] canvas.addr=0x79300000
[ 4.942052@1] fb: osd[0] canvas.width=7680
[ 4.942053@1] fb: osd[0] canvas.height=3240
[ 4.942055@1] fb: osd[0] frame.width=1920
[ 4.942057@0] mmcblk0boot1: unknown partition table
[ 4.942058@1] fb: osd[0] frame.height=1080
[ 4.943021@1] mmcblk0boot0: unknown partition table
[ 4.943306@1] clear_emmc_wait_flag
[ 5.023806@3] sd: new high speed SDHC card at address aaaa
[ 5.024250@1] sd: clock 50000000, 4-bit-bus-width
[ 5.024250@1]
[ 5.024251@1] mmcblk1: sd:aaaa SL08G 7.40 GiB
[ 5.025354@1] mmcblk1: p1 p2
[ 5.064649@0] Console: switching to colour frame buffer device 240x67
[ 5.538548@2] fb: osd probe OK
[ 5.543043@2] ge2d: ge2d_init_module
[ 5.547243@2] ge2d: ge2d_dev major:242
[ 5.551872@3] ge2d: ge2d clock is 400 MHZ
[ 5.555973@3] ge2d: ge2d: pdev=ffffffc06527c400, irq=182, rstc=0xffffffc0643d0540, clk=ffffffc065244700
[ 5.563901@3] ge2d: mapped phy: 0xd0160000
[ 5.567983@3] ge2d: ge2d start monitor
[ 5.572066@0] ge2d: ge2d workqueue monitor start
[ 5.572426@2] codec:Amlogic A/V streaming port init
[ 5.574193@3] codec:get gate demux control ok ffffffc06412c700
[ 5.574198@3] codec:get gate parser_top control ok ffffffc06412c780
[ 5.574203@3] codec:get gate vpu_intr control ok ffffffc06412c800
[ 5.574209@3] codec:get gate vdec control ok ffffffc06412c880
[ 5.574817@3] codec:[tsync_pcr_init]init success.
[ 5.574820@3] codec:amvideocap_init_module
[ 5.574946@3] codec:amvideocap_probe,amvideocap
[ 5.574949@3] codec:use cma buf.
[ 5.574950@3] codec:amvideocap_dev_register
[ 5.576606@3] amvenc_avc_probe -- reserved memory config fail.
[ 5.576609@3] amvenc_avc - cma memory pool size: 40 MB
[ 5.576629@3] encode_wq_init.
[ 5.576634@3] encode start monitor.
[ 5.576686@1] encode workqueue monitor start.
[ 5.577181@3] jpegenc module init
[ 5.577485@3] codec:picdec_driver_probe called.
[ 5.577488@3] picdec has 1 memory regions
[ 5.577512@3] codec:picdec_driver_probe done.
[ 5.578639@3] codec:create_ge2d_work_queue video task ok
[ 5.579059@3] codec:used fix clk for vdec clk source!
[ 5.579064@3] codec:register clk_set_setting cpu[34]
[ 5.579391@3] vpu_init
[ 5.579556@3] vpu_probe
[ 5.579560@3] HevcEnc reserved memory config fail.
[ 5.579563@3] HevcEnc - cma memory pool size: 64 MB
[ 5.579566@3] HevcEnc - wave420l_irq: 219
[ 5.579606@3] vpu base address get from platform driver physical base addr=0xc8810000, virtual base=0xffffff8000588000
[ 5.579945@3] success to probe vpu device with video memory from cma
[ 5.580082@3] DI: di_module_init ok.
[ 5.580086@3] DI: di_module_init: major 235
[ 5.580285@3] DI: di_probe
[ 5.580460@3] deinterlace has 1 memory regions
[ 5.580496@3] deinterlace deinterlace.26: assigned reserved memory node linux,di ok
[ 5.580518@3] di_irq:78,timerc_irq:38
[ 5.744935@3] rdma_register, rdma_table_addr ffffff8000581000 rdma_table_addr_phy 74848000 reg_buf ffffffc0635ee000
[ 5.754556@3] rdma_register success, handle 1 table_size 8192
[ 5.760234@3] DI: di_probe allocate rdma channel 1.
[ 5.765060@3] DI: DI hw version 2.
[ 5.769830@3] 0x000000db:Y=db,U=0,V=0
[ 5.774530@3] 0x000000dc:Y=dc,U=0,V=0
[ 5.779186@3] 0x000000dd:Y=dd,U=0,V=0
[ 5.783837@3] 0x000000de:Y=de,U=0,V=0
[ 5.788434@3] 0x000000df:Y=df,U=0,V=0
[ 5.793026@3] 0x000000e0:Y=e0,U=0,V=0
[ 5.797572@3] 0x000000e1:Y=e1,U=0,V=0
[ 5.802109@3] 0x000000e2:Y=e2,U=0,V=0
[ 5.806634@3] 0x000000e3:Y=e3,U=0,V=0
[ 5.811153@3] 0x000000f0:Y=f0,U=0,V=0
[ 5.815614@3] 0x000000f1:Y=f1,U=0,V=0
[ 5.820036@3] 0x000000f2:Y=f2,U=0,V=0
[ 5.824387@3] 0x000000f3:Y=f3,U=0,V=0
[ 5.828692@3] 0x000000f4:Y=f4,U=0,V=0
[ 5.832922@3] 0x000000f5:Y=f5,U=0,V=0
[ 5.837090@3] 0x000000f6:Y=f6,U=0,V=0
[ 5.841226@3] 0x000000f7:Y=f7,U=0,V=0
[ 5.845318@3] 0x000000f8:Y=f8,U=0,V=0
[ 5.849380@3] 0x000000f9:Y=f9,U=0,V=0
[ 5.853348@3] 0x000000fa:Y=fa,U=0,V=0
[ 5.857234@3] 0x000000fb:Y=fb,U=0,V=0
[ 5.861095@3] 0x000000fc:Y=fc,U=0,V=0
[ 5.865096@3] DI: di_probe here.
[ 5.869392@3] efusekeynum: 4
[ 5.873190@3] efusekeyname: mac offset: 0 size: 6
[ 5.877687@3] efusekeyname: mac_bt offset: 6 size: 6
[ 5.884108@3] efusekeyname: mac_wifi offset: 12 size: 6
[ 5.890474@3] efusekeyname: usid offset: 18 size: 16
[ 5.897239@2] efuse efuse.10: probe OK!
[ 5.901369@2] key unify config unifykey-num is 14
[ 5.905326@2] key unify fact unifykey-num is 14
[ 5.909785@2] aml_unifykeys_probe:1273=============unifykey_devno:e900000
[ 5.916885@2] 6unifykey: device unifykeys created ok
[ 5.921725@2] 6aml_unifykeys_init done!
[ 5.925432@2] PPMGRDRV: warn: ppmgr module init func called
[ 5.931071@2] PPMGRDRV: err: ppmgr_driver_probe called
[ 5.935989@2] ppmgr has 1 memory regions
[ 5.939912@2] PPMGRDRV: info: ppmgr_dev major:232
[ 5.944957@2] PPMGRDRV: info: ppmgr_probe done
[ 5.949488@3] amlogic rfkill init
[ 5.953390@3] enter bt_probe of_node
[ 5.957138@3] not get gpio_en
[ 5.960876@3] power on valid level is high
[ 6.379096@2] ionvideo-000: V4L2 device registered as video13
[ 6.386644@2] ionvid: info: Video Technology Magazine Ion Video
[ 6.392526@2] ionvid: info: Capture Board ver 1.0 successfully loaded
[ 6.398910@2] audio_dsp: [dsp]register dsp to char divece(257)
[ 6.405691@2] amaudio: amaudio: driver amaudio succuess!
[ 6.410327@2] amlvid:err: amlvideo_init called
[ 6.414157@2] amlvid:err: amlvideo_create_instance called
[ 6.421834@2] amlvid:err: v4l2_dev.name=:amlvideo-000
[ 6.426822@3] amlvideo-000: V4L2 device registered as video10
[ 6.432810@3] [RX]-hdmirx: hdmirx_init.
[ 6.436778@3] ESM HLD: Initializing...
[ 6.440769@3] ESM HLD: Registering device range 'esm_rx'...
[ 6.445267@3] ESM HLD: Device range 'esm_rx' has been registered.
[ 6.451322@3] ESM HLD: Creating class /sys/class/elliptic_rx...
[ 6.457298@3] ESM HLD: The class /sys/class/elliptic_rx has been created.
[ 6.463921@3] ESM HLD: Creating device 'esm_rx'...
[ 6.468943@2] ESM HLD: Device 'esm_rx' has been created.
[ 6.473894@2] ESM HLD: Done initializing the HLD driver.
[ 6.479187@2] [viuin..]viuin_init_module viuin module init
[ 6.485119@3] [viuin..]viuin_probe probe ok.
[ 6.488975@2] module init
[ 6.492711@2]
[ 6.492711@2] VECM probe start
[ 6.500049@3] aml_vecm_probe: ok
[ 6.504284@2] saradc c1108680.saradc: initialized by BL30
[ 6.507916@2] saradc c1108680.saradc: calibration start:
[ 6.512955@2] saradc c1108680.saradc: nominal=0, value=5
[ 6.518199@2] saradc c1108680.saradc: nominal=256, value=251
[ 6.523842@2] saradc c1108680.saradc: nominal=512, value=499
[ 6.529420@2] saradc c1108680.saradc: nominal=768, value=750
[ 6.535019@2] saradc c1108680.saradc: nominal=1023, value=997
[ 6.540686@2] saradc c1108680.saradc: calibration end: coef=4202
[ 6.546906@3] remote: Driver init
[ 6.550841@3] remote: platform_data g_remote_ao_offset=580
[ 6.555331@3] remote: platform_data irq =228
[ 6.559616@3] remote: set drvdata completed
[ 6.565522@3] remote: device_create_file completed
[ 6.570169@3] input: aml_keypad as /devices/meson-remote.12/input/input0
[ 6.575823@3] remote: input_register_device completed
[ 6.581652@3] remote: set_remote_mode[74]
[ 6.586766@3] remote: remote config major:229
[ 6.591283@3] remote: physical address:0x636c8000
[ 6.596207@2] gpio-key gpio_keypad.48: gpio_key: 0 name(power) pin()
[ 6.601270@2] gpio-key gpio_keypad.48: amlogic_gpio_name_map_num pin 0!::
[ 6.607997@2] gpio-key gpio_keypad.48: gpio_key: 0 power(147)
[ 6.613712@2] gpio-key gpio_keypad.48: start setup_timer
[ 6.618947@2] gpio-key gpio_keypad.48: power key(116) registed.
[ 6.625087@3] input: gpio_keypad as /devices/gpio_keypad.48/input/input1
[ 6.631746@3] gpio-key gpio_keypad.48: gpio keypad register input device completed.
[ 6.639073@3] input input1: gpio keypad major:228
[ 6.644752@2] Sensor: lsm303d_init
[ 6.649762@2] Sensor: stk8313_init
[ 6.654476@2] Sensor: stk831x_init
[ 6.659156@3] Sensor: mxc622x_acc_init
[ 6.663815@2] Sensor: mxc6255xc_acc_init
[ 6.668389@2] Sensor: l3gd20_gyr_init
[ 6.674143@2] cpuinfo: probe done
[ 6.678992@2] defendkey c8834500.defendkey: defendkey_devno:e300000
[ 6.684429@2] defendkey c8834500.defendkey: defendkey: device defendkey created ok
[ 6.691888@2] defendkey: driver init
[ 6.697180@2] input: cec_input as /devices/virtual/input/input2
[ 6.702395@3] cectx aocec: aml_cec_probe(): no hdmirx reg resource
[ 6.708083@3] cectx aocec: aml_cec_probe(): no hhi reg resource
[ 6.714167@3] cectx aocec: aml_cec_probe(): can't find hdmirx
[ 6.720820@3] cec: wake up flag:0
[ 6.725905@2] aml_aes_dma c883e000.aml_aes: Aml AES_dma
[ 6.730560@2] input input1: key 116 up
[ 6.735739@2] aml_tdes_dma c883e000.aml_tdes: Aml TDES_dma
[ 6.741133@3] aml_sha_dma c883e000.aml_sha: Aml SHA1/SHA224/SHA256 dma
[ 6.748488@3] aml_codec_T9015 c8832000.t9015: aml_T9015_audio_codec_probe
[ 6.756572@3] aml_pcm_dai: pcm mode detection =1
[ 6.761739@3] aml_spdif_dai: enterd aml_spdif_play,set_clock:-1,sample_rate=4
[ 6.767917@3] aml_spdif_dai: set normal 512 fs /4 fs
[ 6.772900@3] aml_audio_hw: IEC958 16bit
[ 6.777517@3] hdmitx: audio: aout notify rate 48000
[ 6.782227@3] hdmitx: audio: aout notify size 16
[ 6.786785@3] hdmitx: audio: aout notify format CT_PCM
[ 6.791360@3] hdmtix: set audio
[ 6.795871@3] hdmitx tx_aud_src = 0
[ 6.800389@3] hdmitx: fs = 3, cd = 4, tmds_clk = 0
[ 6.804871@3] hdmitx aud_n_para = 6144
[ 6.809348@3] hdmitx set channel status
[ 6.813793@3] hdmitx: audio: Audio Type: PCM
[ 6.818171@3] hdmitx: audio: set audio param
[ 7.028759@3] aml_snd_card: headphone detection disable=1
[ 7.033217@3] aml_snd_card: no spk event delay time set
[ 7.038750@3] aml_snd_m8_card aml_m8_snd.47: T9015-audio-hifi <-> I2S.40 mapping ok
[ 7.046287@3] aml_snd_m8_card aml_m8_snd.47: dit-hifi <-> SPDIF.41 mapping ok
[ 7.052968@3] aml_pcm: enter aml_pcm_new dai->name: PCM.42 dai->id: 0
[ 7.059375@3] aml_snd_m8_card aml_m8_snd.47: pcm2bt-pcm <-> PCM.42 mapping ok
[ 7.066266@3] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTL
[ 7.073869@3] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
[ 7.082654@3] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTR
[ 7.090239@3] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[ 7.106263@1] aml_snd_card: audio use jtag pinmux as i2s output, read val =0
WARNING: Unimplemented Sip Call: 0x82000036
[ 7.117812@0] GACT probability NOT on
[ 7.122808@0] Mirror/redirect action on
[ 7.127720@0] u32 classifier
[ 7.132596@0] Actions configured
[ 7.137441@0] Netfilter messages via NETLINK v0.30.
[ 7.142418@0] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 7.148518@1] ctnetlink v0.93: registering with nfnetlink.
[ 7.154254@1] xt_time: kernel timezone is -0000
[ 7.159450@1] ipip: IPv4 over IPv4 tunneling driver
[ 7.165337@1] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.170536@1] arp_tables: (C) 2002 David S. Miller
[ 7.175586@1] TCP: cubic registered
[ 7.180539@1] Initializing XFRM netlink socket
[ 7.186422@0] NET: Registered protocol family 10
[ 7.192643@1] mip6: Mobile IPv6
[ 7.197654@1] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.203017@1] sit: IPv6 over IPv4 tunneling driver
[ 7.209600@0] NET: Registered protocol family 17
[ 7.214743@0] NET: Registered protocol family 15
[ 7.219889@0] Bridge firewalling registered
[ 7.224851@0] l2tp_core: L2TP core driver, V2.0
[ 7.229694@0] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 7.234646@0] l2tp_netlink: L2TP netlink interface
[ 7.239610@0] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 7.245429@0] l2tp_debugfs: L2TP debugfs support
[ 7.250442@0] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 7.256599@0] NET: Registered protocol family 35
[ 7.261821@0] Key type dns_resolver registered
[ 7.267694@0] Registering SWP/SWPB emulation handler
[ 7.275371@0] bio: create slab <bio-1> at 1
[ 7.281733@0] Btrfs loaded
[ 7.286926@0] BTRFS: selftest: Running btrfs free space cache tests
[ 7.292683@0] BTRFS: selftest: Running extent only tests
[ 7.297941@0] BTRFS: selftest: Running bitmap only tests
[ 7.303221@0] BTRFS: selftest: Running bitmap and extent tests
[ 7.308990@0] BTRFS: selftest: Free space cache tests finished
[ 7.314736@0] BTRFS: selftest: Running extent buffer operation tests
[ 7.320872@0] BTRFS: selftest: Running btrfs_split_item tests
[ 7.330918@0] BTRFS: selftest: Running find delalloc tests
[ 7.547890@0] BTRFS: selftest: Running btrfs_get_extent tests
[ 7.553400@0] BTRFS: selftest: Running hole first btrfs_get_extent test
[ 7.648630@0] AppArmor: AppArmor sha1 policy hashing enabled
[ 7.653609@0] regulator-dummy: disabling
[ 8.360992@0] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 8.365940@0] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 8.374086@0] xhci-hcd xhci-hcd.0.auto: irq 62, io mem 0xc9000000
[ 8.379855@0] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.386611@0] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.393955@0] usb usb1: Product: xHCI Host Controller
[ 8.399002@0] usb usb1: Manufacturer: Linux 3.14.29 xhci-hcd
[ 8.404550@0] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 8.410386@0] hub 1-0:1.0: USB hub found
[ 8.415533@0] hub 1-0:1.0: 3 ports detected
[ 8.420978@0] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 8.426141@0] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 8.434039@0] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 8.440797@0] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.448115@0] usb usb2: Product: xHCI Host Controller
[ 8.453340@0] usb usb2: Manufacturer: Linux 3.14.29 xhci-hcd
[ 8.458733@0] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 8.464574@2] hub 2-0:1.0: USB hub found
[ 8.469807@2] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 8.477340@5] console [netcon0] enabled
[ 8.483621@5] netconsole: network logging started
[ 8.489871@5] aml_vrtc rtc.32: setting system clock to 2015-01-01 00:00:16 UTC (1420070416)
[ 8.500312@5] gxbb_pm: enter meson_pm_probe!
[ 8.506654@5] gxbb_pm: meson_pm_probe done
[ 8.513361@1] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 8.520954@1] platform thermal: Driver aml-thermal requests probe deferral
[ 8.527914@1] aml_istbt_dev_ready NULL
[ 8.533304@1] ALSA device list:
[ 8.538614@1] #0: AML-M8AUDIO
[ 8.544525@1] Freeing unused kernel memory: 1180K (ffffffc001e14000 - ffffffc001f3b000)
[ 8.585200@1] systemd-udevd[2066]: starting version 215
[ 8.591939@1] random: systemd-udevd urandom read with 43 bits of entropy available
[ 8.738632@7] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 8.886883@7] usb 1-1: New USB device found, idVendor=05ac, idProduct=1006
[ 8.894907@7] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8.903252@7] usb 1-1: Product: Keyboard Hub
[ 8.909921@7] usb 1-1: Manufacturer: Apple, Inc.
[ 8.916559@7] usb 1-1: SerialNumber: 000000000000
[ 8.946144@0] hub 1-1:1.0: USB hub found
[ 8.951757@0] hub 1-1:1.0: 3 ports detected
[ 8.958773@2] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 8.966744@2] platform thermal: Driver aml-thermal requests probe deferral
[ 9.228637@4] usb 1-1.2: new low-speed USB device number 3 using xhci-hcd
[ 9.355130@7] usb 1-1.2: New USB device found, idVendor=05ac, idProduct=0220
[ 9.355136@7] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 9.355140@7] usb 1-1.2: Product: Apple Keyboard
[ 9.355144@7] usb 1-1.2: Manufacturer: Apple, Inc
[ 9.377094@5] usb 1-1.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 9.377109@5] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 9.413139@2] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 9.419560@6] input: Apple, Inc Apple Keyboard as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.2/1-1.2:1.0/0003:05AC:0220.0001/input/input3
[ 9.419873@6] apple 0003:05AC:0220.0001: input,hidraw0: USB HID v1.11 Keyboard [Apple, Inc Apple Keyboard] on usb-xhci-hcd.0.auto-1.2/input0
[ 9.420861@6] input: Apple, Inc Apple Keyboard as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.2/1-1.2:1.1/0003:05AC:0220.0002/input/input4
[ 9.421128@6] apple 0003:05AC:0220.0002: input,hidraw1: USB HID v1.11 Device [Apple, Inc Apple Keyboard] on usb-xhci-hcd.0.auto-1.2/input1
[ 9.476169@2] platform thermal: Driver aml-thermal requests probe deferral
[ 9.476433@2] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 9.476441@2] platform thermal: Driver aml-thermal requests probe deferral
[ 9.498605@5] usb 1-1.3: new low-speed USB device number 4 using xhci-hcd
[ 9.602668@5] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c05a
[ 9.606630@0] EXT4-fs (mmcblk1p2): mounted filesystem with writeback data mode. Opts: data=writeback
[ 9.624996@5] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 9.625001@5] usb 1-1.3: Product: USB Optical Mouse
[ 9.625005@5] usb 1-1.3: Manufacturer: Logitech
[ 9.625908@5] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 9.653023@5] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0003/input/input5
[ 9.653430@5] hid-generic 0003:046D:C05A.0003: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 9.653728@4] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 9.653741@4] platform thermal: Driver aml-thermal requests probe deferral
[ 9.722432@6] random: nonblocking pool is initialized
[ 10.061922@6] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[ 10.079848@6] systemd[1]: Detected architecture 'arm64'.
[ 10.131011@2] systemd[1]: Inserted module 'autofs4'
[ 10.140491@2] systemd[1]: Set hostname to <amlogic-s905x>.
[ 10.185586@3] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 10.411862@1] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[ 10.431190@1] systemd[1]: Expecting device dev-ttyS0.device...
[ 10.448869@1] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 10.459766@1] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 10.470361@1] systemd[1]: Starting Remote File Systems (Pre).
[ 10.487573@1] systemd[1]: Reached target Remote File Systems (Pre).
[ 10.496754@1] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 10.517741@1] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 10.530364@1] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 10.541672@1] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 10.552793@1] systemd[1]: Starting Paths.
[ 10.570505@1] systemd[1]: Reached target Paths.
[ 10.579244@1] systemd[1]: Starting Encrypted Volumes.
[ 10.596840@1] systemd[1]: Reached target Encrypted Volumes.
[ 10.605478@1] systemd[1]: Starting Swap.
[ 10.622918@1] systemd[1]: Reached target Swap.
[ 10.631457@1] systemd[1]: Expecting device dev-disk-by\x2dlabel-BOOT.device...
[ 10.650387@1] systemd[1]: Starting Root Slice.
[ 10.667744@1] systemd[1]: Created slice Root Slice.
[ 10.676249@1] systemd[1]: Starting Delayed Shutdown Socket.
[ 10.693774@1] systemd[1]: Listening on Delayed Shutdown Socket.
[ 10.702638@1] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 10.721237@1] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 10.731092@1] systemd[1]: Starting Journal Socket (/dev/log).
[ 10.748029@1] systemd[1]: Listening on Journal Socket (/dev/log).
[ 10.756478@1] systemd[1]: Starting User and Session Slice.
[ 10.772722@1] systemd[1]: Created slice User and Session Slice.
[ 10.780866@1] systemd[1]: Starting udev Control Socket.
[ 10.796885@1] systemd[1]: Listening on udev Control Socket.
[ 10.804686@1] systemd[1]: Starting udev Kernel Socket.
[ 10.820542@1] systemd[1]: Listening on udev Kernel Socket.
[ 10.828302@1] systemd[1]: Starting Journal Socket.
[ 10.843970@1] systemd[1]: Listening on Journal Socket.
[ 10.851636@1] systemd[1]: Starting System Slice.
[ 10.867092@1] systemd[1]: Created slice System Slice.
[ 10.874624@1] systemd[1]: Starting system-systemd\x2dfsck.slice.
[ 10.890090@1] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 10.898046@1] systemd[1]: Starting Increase datagram queue length...
[ 10.914801@1] systemd[1]: Starting Restore / save the current clock...
[ 10.937125@1] systemd[1]: Mounting Huge Pages File System...
[ 10.953219@1] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 10.973557@1] systemd[1]: Mounting Debug File System...
[ 10.989761@1] systemd[1]: Starting udev Coldplug all Devices...
[ 11.006483@1] systemd[1]: Mounting POSIX Message Queue File System...
[ 11.024691@1] systemd[1]: Started Set Up Additional Binary Formats.
[ 11.032468@1] systemd[1]: Starting LSB: Set keymap...
[ 11.047954@1] systemd[1]: Starting system-serial\x2dgetty.slice.
[ 11.062875@1] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 11.070621@1] systemd[1]: Starting system-getty.slice.
[ 11.084850@1] systemd[1]: Created slice system-getty.slice.
[ 11.094033@1] systemd[1]: Starting Load Kernel Modules...
[ 11.109231@1] systemd[1]: Started File System Check on Root Device.
[ 11.116613@1] systemd[1]: Starting Slices.
[ 11.126218@3] fuse init (API version 7.22)
[ 11.130288@3] Triggered SDIO WiFi power on and bus rescan.
[ 11.130307@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 11.151298@1] systemd[1]: Reached target Slices.
[ 11.166188@1] systemd[1]: Mounted POSIX Message Queue File System.
[ 11.180636@1] systemd[1]: Mounted Debug File System.
[ 11.194379@1] systemd[1]: Mounted Huge Pages File System.
[ 11.209000@1] systemd[1]: Started Increase datagram queue length.
[ 11.224554@1] systemd[1]: Started Restore / save the current clock.
[ 11.240375@1] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 11.261241@1] systemd[1]: Started LSB: Set keymap.
[ 11.269496@1] systemd[1]: Time has been changed
[ 11.302966@1] systemd[1]: Started udev Coldplug all Devices.
[ 11.330668@1] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 11.347473@1] systemd[1]: Starting Syslog Socket.
[ 11.361971@1] systemd[1]: Listening on Syslog Socket.
[ 11.368916@1] systemd[1]: Starting Journal Service...
[ 11.391723@1] systemd[1]: Started Journal Service.
[ 11.438606@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 11.447939@3] systemd-udevd[2169]: starting version 215
[ 11.782745@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 11.793608@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 11.804857@6] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 11.821878@2] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 11.833755@1] ionvid: info: ionvideo open
[ 11.928890@5] sdio: clk 200000000 SDR mode tuning start
[ 11.936530@5] sdio: rx_tuning_result[0] = 10
[ 11.944085@5] sdio: rx_tuning_result[1] = 10
[ 11.951575@3] sdio: rx_tuning_result[2] = 10
[ 11.957679@3] sdio: rx_tuning_result[3] = 10
[ 11.963462@3] sdio: best_win_start =0, best_win_size =4
[ 11.969229@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 11.976727@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 11.987505@3] sdio: queuing unknown CIS tuple 0x91 (3 bytes)
[ 11.993272@3] sdio: new ultra high speed SDR104 SDIO card at address 0001
[ 12.000133@3] sdio: clock 200000000, 4-bit-bus-width
[ 12.006177@7] [sdio_reinit] finish
[ 12.038551@1] ionvid: info: ionvideo_stop_generating!!!!
[ 12.044362@1] ionvid: info: ionvideo release
[ 12.098806@5] aml_nftl_dev: module license 'Proprietary' taints kernel.
[ 12.106749@5] Disabling lock debugging due to kernel taint
[ 12.115776@3] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 12.124004@3] platform thermal: Driver aml-thermal requests probe deferral
[ 12.174574@7] cfg80211: Calling CRDA to update world regulatory domain
[ 12.275950@6] dhd_module_init: in
[ 12.282908@6] ======== bcm_wlan_set_plat_data ========
[ 12.289845@6] host_oob_irq: 100
[ 12.296641@6] host_oob_irq_flags=0x414
[ 12.303368@6] dhd_wifi_platform_load: Enter
[ 12.310110@2] Power-up adapter 'DHD generic adapter'
[ 12.315602@2] wifi_platform_set_power = 1
[ 12.321000@2] ======== PULL WL_REG_ON HIGH! ========
[ 12.326437@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 12.405030@6] cfg80211: World regulatory domain updated:
[ 12.411648@6] cfg80211: DFS Master region: unset
[ 12.415732@6] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.431358@6] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 12.440129@1] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 12.447466@1] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 12.455018@1] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 12.462506@1] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 12.470013@1] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[ 12.477577@1] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 12.477580@1] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 12.533324@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 13.038580@3] wifi_platform_bus_enumerate device present 1
[ 13.044055@3] ======== Card detection to detect SDIO card! ========
[ 13.050170@3] sdio_reset_comm():
[ 13.083931@3] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 13.092185@3] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 13.100343@3] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 13.110551@3] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 13.209917@5] sdio: clk 200000000 SDR mode tuning start
[ 13.216658@5] sdio: rx_tuning_result[0] = 10
[ 13.223414@5] sdio: rx_tuning_result[1] = 10
[ 13.230197@3] sdio: rx_tuning_result[2] = 10
[ 13.235829@3] sdio: rx_tuning_result[3] = 10
[ 13.241247@3] sdio: best_win_start =0, best_win_size =4
[ 13.246530@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 13.253678@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 13.259792@3] [sdio_reinit] finish
[ 13.265680@5] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 13.274775@5] platform thermal: Driver aml-thermal requests probe deferral
[ 13.281658@3] bcmsdh_register: register client driver
[ 13.281769@3] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[ 13.281841@3] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[ 13.281844@3] bus num (host idx)=0, slot num (rca)=1
[ 13.281846@3] found adapter info 'DHD generic adapter'
[ 13.281902@3] sdioh_attach: set sd_f2_blocksize 128
[ 13.282245@3] dhdsdio_probe : no mutex held. set lock
[ 13.282371@3] F1 signature read @0x18000000=0x15264345
[ 13.285745@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 13.286427@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 13.286513@3] dhd_conf_set_chiprev: chip=0x4345, chiprev=6
[ 13.286555@3] dhd_conf_set_conf_path_by_nv_path: config_path=/lib/firmware/brcm/config.txt
[ 13.366811@2] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 13.371166@7] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 13.371173@7] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 13.371361@7] dhd_conf_read_config: PM = 0
[ 13.371936@5] wl_create_event_handler(): thread:wl_event_handler:8e4 started
[ 13.371952@1] tsk Enter, tsk = 0xffffff80015d2940
[ 13.372170@5] dhd_attach(): thread:dhd_watchdog_thread:8e5 started
[ 13.372217@5] dhd_attach(): thread:dhd_dpc:8e6 started
[ 13.372244@1] dhd_dpc_thread: set dpc_cpucore 0 from config.txt
[ 13.372258@5] dhd_attach(): thread:dhd_rxf:8e7 started
[ 13.372269@5] dhd_deferred_work_init: work queue initialized
[ 13.383873@5] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 13.383873@5] Compiled in drivers/net/wireless/bcmdhd
[ 13.384461@5] Register interface [wlan0] MAC: 44:2c:05:f5:4a:5a
[ 13.384461@5]
[ 13.384467@5] dhd_prot_ioctl : bus is down. we have nothing to do
[ 13.384530@5] bcmsdh_oob_intr_unregister: Enter
[ 13.384532@5] bcmsdh_oob_intr_unregister: irq is not registered
[ 13.384541@5] dhd_txglom_enable: enable 0
[ 13.384544@5] dhd_conf_set_txglom_params: swtxglom=0, txglom_ext=0
[ 13.384546@5] dhd_conf_set_txglom_params: txglom_bucket_size=0
[ 13.384548@5] dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0, bus_txglom=0
[ 13.384550@5] dhd_conf_set_txglom_params: tx_in_rx=1, tx_max_offset=0
[ 13.384552@5] dhd_bus_devreset: WLAN OFF DONE
[ 13.384604@5] wifi_platform_set_power = 0
[ 13.384606@5] ======== PULL WL_REG_ON LOW! ========
[ 13.384610@5] dhdsdio_probe : the lock is released.
[ 13.384687@5] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[ 13.384737@5] dhd_module_init: Exit err=0
[ 13.418366@4] Bluetooth: Core ver 2.18
[ 13.418418@4] NET: Registered protocol family 31
[ 13.418421@4] Bluetooth: HCI device and connection manager initialized
[ 13.418453@4] Bluetooth: HCI socket layer initialized
[ 13.418459@4] Bluetooth: L2CAP socket layer initialized
[ 13.418491@4] Bluetooth: SCO socket layer initialized
[ 13.422957@6] Bluetooth: Generic Bluetooth SDIO driver ver 0.1
[ 13.585157@2] platform thermal: Driver aml-thermal requests probe deferral
[ 13.592191@2] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 13.599841@2] platform thermal: Driver aml-thermal requests probe deferral
[ 16.811998@7] EXT4-fs (mmcblk1p2): re-mounted. Opts: commit=600,errors=remount-ro
[ 17.063426@4] systemd-journald[2167]: Received request to flush runtime journal from PID 1
[ 19.768020@3] vout_serve: vmode set to 720p60hz
[ 19.768020@3]
[ 19.778921@3] fb: current vmode=1080p60hz
[ 19.784092@3] tv_vout: tv_set_current_vmode[759]fps_target_mode=10
[ 19.789859@3] tv_vout: mode is 10,sync_duration_den=1,sync_duration_num=60
[ 19.796601@3] tv_vout: TV mode 720p60hz selected.
[ 19.801867@3]
[ 19.801867@3] vdac_enable: on:0,module_sel:8
[ 19.812523@3]
[ 19.812523@3] vdac_enable: on:0,module_sel:8
[ 19.823092@3] tv_vout: new mode =720p60hz set ok
[ 19.828116@3] vout_serve: vinfo mode is: 720p60hz
[ 19.833155@3] vout_serve: new mode 720p60hz
[ 19.833155@3] set ok
[ 19.843693@3] hdmitx: video: get current mode: 720p60hz
[ 19.848841@3] hdmitx: update rx hdr info 0
[ 19.853607@3] hdmitx: get ext_name
[ 19.858394@3] hdmitx: system: already init VIC = 0 Now VIC = 4
[ 19.863591@3] hdmitx: rx no SCDC present indicator
[ 19.870428@3] hdmitx: ddc rd8b error 0x54 0x01
[ 19.877252@3] hdmitx: ddc rd8b error 0x54 0x01
[ 19.882059@3] hdmirx version is 1.4 or below
[ 19.886765@3] hdmitx div40: 0
[ 19.918630@3] hdmitx: system: set mode VIC 4 (cd0,cs0,pm1,vd0,1)
[ 19.923749@3] hdmitx: system: set pll
[ 19.928455@3] hdmitx: system: param->VIC:4
[ 19.935278@3] hdmitx: ddc w1b error 0x54 0x20 0x00
[ 19.942097@3] hdmitx: ddc w1b error 0x54 0x20 0x00
[ 19.948830@3] hdmitx: ddc rd8b error 0x54 0x21
[ 19.953604@3] hdmitx: set clk: VIC = 4 cd = 4
[ 19.958336@3] config HPLL = 2970000
[ 19.963116@3] HPLL: 0xc000027b
[ 19.967760@3] config HPLL done
[ 19.972447@1] set_hpll_od3_clk_div[441] div = 6
[ 19.977068@1] j = 2 vid_clk_div = 1
[ 19.981682@1] hdmitx: set enc for VIC: 4
[ 19.986272@1] hdmitx_set_hw[4867] set VIC = 4
[ 20.120608@3] hdmitx: system: phy setting done
[ 20.120635@0] hdmitx: system: irq 80000001
[ 20.120795@0] Start = 0x10000100 End = 0x100001ff
[ 20.120804@0] [0x10000104]: 0x00000001
[ 20.120992@0] [0x10000180]: 0x000000ff
[ 20.120995@0] [0x10000181]: 0x000000ff
[ 20.120998@0] [0x10000182]: 0x00000003
[ 20.121001@0] [0x10000183]: 0x00000007
[ 20.121004@0] [0x10000184]: 0x0000003f
[ 20.121007@0] [0x10000185]: 0x00000002
[ 20.121011@0] [0x10000187]: 0x000000ff
[ 20.121014@0] [0x10000188]: 0x00000003
[ 20.124628@3] Sink is HDMI device
[ 20.124638@3] hdmitx: system: packet: can't get vendor data
[ 20.124642@3] hdmtix: set audio
[ 20.124651@3] hdmitx tx_aud_src = 0
[ 20.124679@3] hdmitx: fs = 3, cd = 4, tmds_clk = 74250
[ 20.124681@3] hdmitx aud_n_para = 6144
[ 20.124700@3] hdmitx set channel status
[ 20.124762@3] hdmitx: audio: Audio Type: PCM
[ 20.124769@3] fb: current vmode=720p60hz
[ 20.265951@0] fb: osd[0] canvas.idx =0x40
[ 20.265953@0] fb: osd[0] canvas.addr=0x79300000
[ 20.265956@0] fb: osd[0] canvas.width=3840
[ 20.265957@0] fb: osd[0] canvas.height=1440
[ 20.265959@0] fb: osd[0] frame.width=1280
[ 20.265960@0] fb: osd[0] frame.height=720
[ 20.321402@0] fb: use ion buffer for fb memory
[ 20.321522@0] meson-fb meson-fb.16: create ion_client ffffffc0640189c0, handle=ffffffc052d91500
[ 20.321527@0] meson-fb meson-fb.16: ion memory(1): created fb at 0x000000007ab51000, size 1 MiB
[ 20.321533@0] fb: Frame buffer memory assigned at
[ 20.321533@0] fb: 1, phy: 0x000000007ab51000, vir:0xffffff8003bfd000, size=1024K
[ 20.321533@0]
[ 20.321536@0] fb: fb1 open, logo index:1
[ 20.338845@5] libphy: stmmac-0:00 - Link is Up - 100/Full
[ 20.365305@0] fb: osd[1] canvas.idx =0x43
[ 20.365308@0] fb: osd[1] canvas.addr=0x7ab51000
[ 20.365309@0] fb: osd[1] canvas.width=128
[ 20.365311@0] fb: osd[1] canvas.height=32
[ 20.365313@0] fb: osd[1] frame.width=32
[ 20.365314@0] fb: osd[1] frame.height=32
[ 20.393664@7] vout_serve: vmode set to 720p60hz
[ 20.393664@7]
[ 20.400876@7] vout_serve: don't set the same mode as current
[ 20.406566@7] fb: osd0 free scale DISABLE
[ 20.423505@7] fb: osd[0] enable: 1 (amlogics905x_in)
[ 20.854084@0] dhd_open: Enter ffffffc052ca5000
[ 20.858008@0]
[ 20.858008@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 20.858008@0] Compiled in drivers/net/wireless/bcmdhd
[ 20.876218@0] wl_android_wifi_on in 1
[ 20.880411@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 20.884455@0] wifi_platform_set_power = 1
[ 20.888492@0] ======== PULL WL_REG_ON HIGH! ========
[ 20.893403@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 21.100382@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 21.608551@0] sdio_reset_comm():
[ 21.640672@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 21.647987@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 21.655166@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 21.664329@7] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 21.762142@7] sdio: clk 200000000 SDR mode tuning start
[ 21.766718@7] sdio: rx_tuning_result[0] = 10
[ 21.771252@7] sdio: rx_tuning_result[1] = 10
[ 21.775696@7] sdio: rx_tuning_result[2] = 10
[ 21.780135@7] sdio: rx_tuning_result[3] = 10
[ 21.784343@0] sdio: best_win_start =0, best_win_size =4
[ 21.788103@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 21.795487@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 21.801664@0] sdioh_start: set sd_f2_blocksize 128
[ 21.806765@0]
[ 21.806765@0]
[ 21.806765@0] dhd_bus_devreset: == WLAN ON ==
[ 21.819599@0] F1 signature read @0x18000000=0x15264345
[ 21.828080@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 21.833335@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 21.840065@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 21.844942@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 21.852877@0] dhd_conf_read_config: PM = 0
[ 21.856858@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 21.865574@0] dhdsdio_download_firmware: set use_rxchain 0
[ 21.871002@0] dhdsdio_download_firmware: set txglomsize 40
[ 21.876445@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 21.881967@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 21.888151@0] Final nv_path=/lib/firmware/brcm/
[ 21.892671@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 21.898733@0] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 21.907845@0] _dhdsdio_download_firmware: dongle image file download failed
[ 21.914783@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 21.920085@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 21.926125@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 21.931530@0] wifi_platform_set_power = 0
[ 21.935877@0] ======== PULL WL_REG_ON LOW! ========
[ 21.940308@0] wl_android_wifi_on: Failed
[ 21.944129@0] dhd_open : wl_android_wifi_on failed (-35)
[ 21.949409@0] dhd_stop: Enter ffffffc052ca5000
[ 21.953788@0] wl_android_wifi_off in 1
[ 21.957586@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 21.962345@0] wl_android_wifi_off out
[ 21.966017@0] dhd_stop: Exit
[ 21.969689@0] dhd_open: Exit ret=-1
[ 22.120073@5] dhd_open: Enter ffffffc052ca5000
[ 22.120081@5]
[ 22.120081@5] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 22.120081@5] Compiled in drivers/net/wireless/bcmdhd
[ 22.120084@5] wl_android_wifi_on in 1
[ 22.120086@5] wl_android_wifi_on in 2: g_wifi_on=0
[ 22.120089@5] wifi_platform_set_power = 1
[ 22.120091@5] ======== PULL WL_REG_ON HIGH! ========
[ 22.120115@5] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 22.320171@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 22.828576@0] sdio_reset_comm():
[ 22.860808@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 22.868341@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 22.876339@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 22.885845@4] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 22.984480@5] sdio: clk 200000000 SDR mode tuning start
[ 22.989430@5] sdio: rx_tuning_result[0] = 10
[ 22.994189@5] sdio: rx_tuning_result[1] = 10
[ 22.998807@5] sdio: rx_tuning_result[2] = 10
[ 23.003427@2] sdio: rx_tuning_result[3] = 10
[ 23.006872@2] sdio: best_win_start =0, best_win_size =4
[ 23.011147@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 23.018388@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 23.024629@2] sdioh_start: set sd_f2_blocksize 128
[ 23.029693@2]
[ 23.029693@2]
[ 23.029693@2] dhd_bus_devreset: == WLAN ON ==
[ 23.041824@2] F1 signature read @0x18000000=0x15264345
[ 23.050374@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 23.055357@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 23.062056@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 23.066980@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 23.074984@2] dhd_conf_read_config: PM = 0
[ 23.078893@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 23.087592@2] dhdsdio_download_firmware: set use_rxchain 0
[ 23.093064@2] dhdsdio_download_firmware: set txglomsize 40
[ 23.098458@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 23.104055@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 23.110218@2] Final nv_path=/lib/firmware/brcm/
[ 23.114672@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 23.120759@2] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 23.129931@2] _dhdsdio_download_firmware: dongle image file download failed
[ 23.136813@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 23.142146@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 23.148142@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 23.153598@2] wifi_platform_set_power = 0
[ 23.157450@2] ======== PULL WL_REG_ON LOW! ========
[ 23.162365@2] wl_android_wifi_on: Failed
[ 23.166166@2] dhd_open : wl_android_wifi_on failed (-35)
[ 23.171467@2] dhd_stop: Enter ffffffc052ca5000
[ 23.175824@2] wl_android_wifi_off in 1
[ 23.179645@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 23.184361@2] wl_android_wifi_off out
[ 23.188034@2] dhd_stop: Exit
[ 23.191783@2] dhd_open: Exit ret=-1
[ 23.196216@2] dhd_open: Enter ffffffc052ca5000
[ 23.199912@2]
[ 23.199912@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 23.199912@2] Compiled in drivers/net/wireless/bcmdhd
[ 23.217832@2] wl_android_wifi_on in 1
[ 23.221680@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 23.226162@2] wifi_platform_set_power = 1
[ 23.230620@2] ======== PULL WL_REG_ON HIGH! ========
[ 23.235167@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 23.442017@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 23.948568@2] sdio_reset_comm():
[ 23.980754@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 23.988099@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 24.093527@7] sdio: clk 200000000 SDR mode tuning start
[ 24.099161@7] sdio: rx_tuning_result[0] = 10
[ 24.104084@7] sdio: rx_tuning_result[1] = 10
[ 24.108967@7] sdio: rx_tuning_result[2] = 10
[ 24.113814@3] sdio: rx_tuning_result[3] = 10
[ 24.117587@3] sdio: best_win_start =0, best_win_size =4
[ 24.121618@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 24.128928@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 24.135056@3] sdioh_start: set sd_f2_blocksize 128
[ 24.140203@3]
[ 24.140203@3]
[ 24.140203@3] dhd_bus_devreset: == WLAN ON ==
[ 24.152866@3] F1 signature read @0x18000000=0x15264345
[ 24.161335@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 24.166578@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 24.173330@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 24.178236@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 24.186242@3] dhd_conf_read_config: PM = 0
[ 24.190198@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 24.198920@3] dhdsdio_download_firmware: set use_rxchain 0
[ 24.204278@3] dhdsdio_download_firmware: set txglomsize 40
[ 24.209783@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 24.215231@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 24.221518@3] Final nv_path=/lib/firmware/brcm/
[ 24.225926@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 24.232054@3] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 24.241205@3] _dhdsdio_download_firmware: dongle image file download failed
[ 24.248068@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 24.253433@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 24.259471@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 24.264818@3] wifi_platform_set_power = 0
[ 24.268765@3] ======== PULL WL_REG_ON LOW! ========
[ 24.273537@3] wl_android_wifi_on: Failed
[ 24.277456@3] dhd_open : wl_android_wifi_on failed (-35)
[ 24.282758@3] dhd_stop: Enter ffffffc052ca5000
[ 24.287078@3] wl_android_wifi_off in 1
[ 24.291057@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 24.295616@3] wl_android_wifi_off out
[ 24.299535@3] dhd_stop: Exit
[ 24.303364@3] dhd_open: Exit ret=-1
[ 24.315339@3] dhd_open: Enter ffffffc052ca5000
[ 24.319243@3]
[ 24.319243@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 24.319243@3] Compiled in drivers/net/wireless/bcmdhd
[ 24.337394@3] wl_android_wifi_on in 1
[ 24.341255@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 24.345652@3] wifi_platform_set_power = 1
[ 24.349716@3] ======== PULL WL_REG_ON HIGH! ========
[ 24.354554@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 24.561637@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 25.068594@3] sdio_reset_comm():
[ 25.204032@7] sdio: clk 200000000 SDR mode tuning start
[ 25.209056@7] sdio: rx_tuning_result[0] = 10
[ 25.213947@7] sdio: rx_tuning_result[1] = 10
[ 25.218789@5] sdio: rx_tuning_result[2] = 10
[ 25.223648@5] sdio: rx_tuning_result[3] = 10
[ 25.228217@3] sdio: best_win_start =0, best_win_size =4
[ 25.232127@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 25.239361@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 25.245516@3] sdioh_start: set sd_f2_blocksize 128
[ 25.250673@3]
[ 25.250673@3]
[ 25.250673@3] dhd_bus_devreset: == WLAN ON ==
[ 25.263785@3] F1 signature read @0x18000000=0x15264345
[ 25.272313@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 25.277649@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 25.284408@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 25.289410@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 25.297226@3] dhd_conf_read_config: PM = 0
[ 25.301283@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 25.310008@3] dhdsdio_download_firmware: set use_rxchain 0
[ 25.315351@3] dhdsdio_download_firmware: set txglomsize 40
[ 25.320861@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 25.326305@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 25.332588@3] Final nv_path=/lib/firmware/brcm/
[ 25.336999@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 25.343107@3] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 25.352275@3] _dhdsdio_download_firmware: dongle image file download failed
[ 25.359189@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 25.364430@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 25.370554@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 25.375894@3] wifi_platform_set_power = 0
[ 25.379857@3] ======== PULL WL_REG_ON LOW! ========
[ 25.384610@3] wl_android_wifi_on: Failed
[ 25.388595@3] dhd_open : wl_android_wifi_on failed (-35)
[ 25.393753@3] dhd_stop: Enter ffffffc052ca5000
[ 25.398148@3] wl_android_wifi_off in 1
[ 25.402169@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 25.406688@3] wl_android_wifi_off out
[ 25.410630@3] dhd_stop: Exit
[ 25.414510@3] dhd_open: Exit ret=-1
[ 25.419050@3] dhd_open: Enter ffffffc052ca5000
[ 25.423525@3]
[ 25.423525@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 25.423525@3] Compiled in drivers/net/wireless/bcmdhd
[ 25.443573@3] wl_android_wifi_on in 1
[ 25.447971@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 25.452426@3] wifi_platform_set_power = 1
[ 25.456234@3] ======== PULL WL_REG_ON HIGH! ========
[ 25.460819@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 25.475311@4] meson_uart c81004c0.[ 25.483411@4] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 25.513656@4] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 25.513853@4] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 25.667667@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 26.178593@3] sdio_reset_comm():
[ 26.314717@5] sdio: clk 200000000 SDR mode tuning start
[ 26.320139@5] sdio: rx_tuning_result[0] = 10
[ 26.326176@5] sdio: rx_tuning_result[1] = 10
[ 26.331305@5] sdio: rx_tuning_result[2] = 10
[ 26.336383@3] sdio: rx_tuning_result[3] = 10
[ 26.340365@3] sdio: best_win_start =0, best_win_size =4
[ 26.344160@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 26.351493@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 26.357624@3] sdioh_start: set sd_f2_blocksize 128
[ 26.362764@3]
[ 26.362764@3]
[ 26.362764@3] dhd_bus_devreset: == WLAN ON ==
[ 26.376193@3] F1 signature read @0x18000000=0x15264345
[ 26.384685@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 26.390098@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 26.396716@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 26.401785@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 26.409681@3] dhd_conf_read_config: PM = 0
[ 26.414011@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 26.422391@3] dhdsdio_download_firmware: set use_rxchain 0
[ 26.427744@3] dhdsdio_download_firmware: set txglomsize 40
[ 26.433256@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 26.438746@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 26.444905@3] Final nv_path=/lib/firmware/brcm/
[ 26.449456@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 26.455437@3] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 26.464651@3] _dhdsdio_download_firmware: dongle image file download failed
[ 26.471605@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 26.476822@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 26.482942@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 26.488286@3] wifi_platform_set_power = 0
[ 26.492611@3] ======== PULL WL_REG_ON LOW! ========
[ 26.497001@3] wl_android_wifi_on: Failed
[ 26.501332@3] dhd_open : wl_android_wifi_on failed (-35)
[ 26.506146@3] dhd_stop: Enter ffffffc052ca5000
[ 26.510618@3] wl_android_wifi_off in 1
[ 26.514768@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 26.519420@3] wl_android_wifi_off out
[ 26.523473@3] dhd_stop: Exit
[ 26.527482@3] dhd_open: Exit ret=-1
[ 26.535329@3] dhd_open: Enter ffffffc052ca5000
[ 26.539353@3]
[ 26.539353@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 26.539353@3] Compiled in drivers/net/wireless/bcmdhd
Debian GNU/Li[ 26.557753@3] wl_android_wifi_on in 1
nux 8 amlogic-s905x ttyS0
[ 26.562497@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 26.569743@3] wifi_platform_set_power = 1
[ 26.573623@3] ======== PULL WL_REG_ON HIGH! ========
[ 26.578640@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
amlogic-s905x login: [ 26.785486@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 27.298594@3] sdio_reset_comm():
[ 27.330736@7] sdio_read_cis: 10 callbacks suppressed
[ 27.335431@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 27.343016@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 27.350282@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 27.359722@0] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 27.457653@4] sdio: clk 200000000 SDR mode tuning start
[ 27.463244@5] sdio: rx_tuning_result[0] = 10
[ 27.468044@5] sdio: rx_tuning_result[1] = 10
[ 27.472777@5] sdio: rx_tuning_result[2] = 10
[ 27.477379@2] sdio: rx_tuning_result[3] = 10
[ 27.480988@2] sdio: best_win_start =0, best_win_size =4
[ 27.485067@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 27.492485@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 27.498632@2] sdioh_start: set sd_f2_blocksize 128
[ 27.503678@2]
[ 27.503678@2]
[ 27.503678@2] dhd_bus_devreset: == WLAN ON ==
[ 27.515805@2] F1 signature read @0x18000000=0x15264345
[ 27.524564@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 27.529632@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 27.536280@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 27.541289@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 27.549220@2] dhd_conf_read_config: PM = 0
[ 27.553129@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 27.561895@2] dhdsdio_download_firmware: set use_rxchain 0
[ 27.567287@2] dhdsdio_download_firmware: set txglomsize 40
[ 27.572754@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 27.578239@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 27.584523@2] Final nv_path=/lib/firmware/brcm/
[ 27.588965@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 27.595007@2] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 27.604171@2] _dhdsdio_download_firmware: dongle image file download failed
[ 27.611151@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 27.616364@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 27.622447@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 27.627835@2] wifi_platform_set_power = 0
[ 27.631758@2] ======== PULL WL_REG_ON LOW! ========
[ 27.636545@2] wl_android_wifi_on: Failed
[ 27.640498@2] dhd_open : wl_android_wifi_on failed (-35)
[ 27.645690@2] dhd_stop: Enter ffffffc052ca5000
[ 27.650118@2] wl_android_wifi_off in 1
[ 27.653943@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 27.658648@2] wl_android_wifi_off out
[ 27.662386@2] dhd_stop: Exit
[ 27.666031@2] dhd_open: Exit ret=-1
[ 27.670329@2] dhd_open: Enter ffffffc052ca5000
[ 27.673970@2]
[ 27.673970@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 27.673970@2] Compiled in drivers/net/wireless/bcmdhd
[ 27.691896@2] wl_android_wifi_on in 1
[ 27.695676@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 27.700293@2] wifi_platform_set_power = 1
[ 27.704181@2] ======== PULL WL_REG_ON HIGH! ========
[ 27.709156@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 27.916033@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 28.428567@2] sdio_reset_comm():
[ 28.460742@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 28.468096@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 28.475378@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 28.485403@7] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 28.584595@7] sdio: clk 200000000 SDR mode tuning start
[ 28.589496@7] sdio: rx_tuning_result[0] = 10
[ 28.594295@7] sdio: rx_tuning_result[1] = 10
[ 28.599001@7] sdio: rx_tuning_result[2] = 10
[ 28.603715@0] sdio: rx_tuning_result[3] = 10
[ 28.607340@0] sdio: best_win_start =0, best_win_size =4
[ 28.611414@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 28.618719@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 28.624946@0] sdioh_start: set sd_f2_blocksize 128
[ 28.630035@0]
[ 28.630035@0]
[ 28.630035@0] dhd_bus_devreset: == WLAN ON ==
[ 28.642322@0] F1 signature read @0x18000000=0x15264345
[ 28.650942@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 28.656143@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 28.662835@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 28.667749@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 28.675746@0] dhd_conf_read_config: PM = 0
[ 28.679668@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 28.688401@0] dhdsdio_download_firmware: set use_rxchain 0
[ 28.693821@0] dhdsdio_download_firmware: set txglomsize 40
[ 28.699248@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 28.704731@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 28.711029@0] Final nv_path=/lib/firmware/brcm/
[ 28.715426@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 28.721574@0] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 28.730717@0] _dhdsdio_download_firmware: dongle image file download failed
[ 28.737572@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 28.742954@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 28.748927@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 28.754327@0] wifi_platform_set_power = 0
[ 28.758260@0] ======== PULL WL_REG_ON LOW! ========
[ 28.763100@0] wl_android_wifi_on: Failed
[ 28.767479@0] dhd_open : wl_android_wifi_on failed (-35)
[ 28.772272@0] dhd_stop: Enter ffffffc052ca5000
[ 28.776577@0] wl_android_wifi_off in 1
[ 28.780435@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 28.785125@0] wl_android_wifi_off out
[ 28.788882@0] dhd_stop: Exit
[ 28.792584@0] dhd_open: Exit ret=-1
[ 28.801650@0] dhd_open: Enter ffffffc052ca5000
[ 28.805341@0]
[ 28.805341@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 28.805341@0] Compiled in drivers/net/wireless/bcmdhd
[ 28.823284@0] wl_android_wifi_on in 1
[ 28.827066@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 28.831632@0] wifi_platform_set_power = 1
[ 28.835530@0] ======== PULL WL_REG_ON HIGH! ========
[ 28.840561@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 29.047388@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 29.558581@0] sdio_reset_comm():
[ 29.590749@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 29.598097@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 29.703632@4] sdio: clk 200000000 SDR mode tuning start
[ 29.708555@7] sdio: rx_tuning_result[0] = 10
[ 29.713503@4] sdio: rx_tuning_result[1] = 10
[ 29.718364@4] sdio: rx_tuning_result[2] = 10
[ 29.723243@3] sdio: rx_tuning_result[3] = 10
[ 29.727021@3] sdio: best_win_start =0, best_win_size =4
[ 29.731008@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 29.738248@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 29.744482@3] sdioh_start: set sd_f2_blocksize 128
[ 29.749542@3]
[ 29.749542@3]
[ 29.749542@3] dhd_bus_devreset: == WLAN ON ==
[ 29.762059@3] F1 signature read @0x18000000=0x15264345
[ 29.770487@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 29.775620@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 29.782355@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 29.787322@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 29.795271@3] dhd_conf_read_config: PM = 0
[ 29.799233@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 29.807937@3] dhdsdio_download_firmware: set use_rxchain 0
[ 29.813394@3] dhdsdio_download_firmware: set txglomsize 40
[ 29.818831@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 29.824321@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 29.830555@3] Final nv_path=/lib/firmware/brcm/
[ 29.835017@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 29.841068@3] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 29.850235@3] _dhdsdio_download_firmware: dongle image file download failed
[ 29.857137@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 29.862478@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 29.868483@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 29.873916@3] wifi_platform_set_power = 0
[ 29.877797@3] ======== PULL WL_REG_ON LOW! ========
[ 29.882657@3] wl_android_wifi_on: Failed
[ 29.886537@3] dhd_open : wl_android_wifi_on failed (-35)
[ 29.891796@3] dhd_stop: Enter ffffffc052ca5000
[ 29.896169@3] wl_android_wifi_off in 1
[ 29.900048@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 29.904707@3] wl_android_wifi_off out
[ 29.908556@3] dhd_stop: Exit
[ 29.912342@3] dhd_open: Exit ret=-1
[ 29.916663@3] dhd_open: Enter ffffffc052ca5000
[ 29.920530@3]
[ 29.920530@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 29.920530@3] Compiled in drivers/net/wireless/bcmdhd
[ 29.938474@3] wl_android_wifi_on in 1
[ 29.942247@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 29.946806@3] wifi_platform_set_power = 1
[ 29.950801@3] ======== PULL WL_REG_ON HIGH! ========
[ 29.955710@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 30.162637@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 30.668595@3] sdio_reset_comm():
[ 30.804016@7] sdio: clk 200000000 SDR mode tuning start
[ 30.809034@4] sdio: rx_tuning_result[0] = 10
[ 30.813935@4] sdio: rx_tuning_result[1] = 10
[ 30.818789@4] sdio: rx_tuning_result[2] = 10
[ 30.823660@4] sdio: rx_tuning_result[3] = 10
[ 30.828226@2] sdio: best_win_start =0, best_win_size =4
[ 30.832098@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 30.839337@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 30.845517@2] sdioh_start: set sd_f2_blocksize 128
[ 30.850685@2]
[ 30.850685@2]
[ 30.850685@2] dhd_bus_devreset: == WLAN ON ==
[ 30.863743@2] F1 signature read @0x18000000=0x15264345
[ 30.872203@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 30.877526@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 30.884308@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 30.889224@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 30.897111@2] dhd_conf_read_config: PM = 0
[ 30.901121@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 30.909879@2] dhdsdio_download_firmware: set use_rxchain 0
[ 30.915236@2] dhdsdio_download_firmware: set txglomsize 40
[ 30.920705@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 30.926189@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 30.932438@2] Final nv_path=/lib/firmware/brcm/
[ 30.936884@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 30.943037@2] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 30.952121@2] _dhdsdio_download_firmware: dongle image file download failed
[ 30.959049@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 30.964313@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 30.970427@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 30.975785@2] wifi_platform_set_power = 0
[ 30.979701@2] ======== PULL WL_REG_ON LOW! ========
[ 30.984493@2] wl_android_wifi_on: Failed
[ 30.988403@2] dhd_open : wl_android_wifi_on failed (-35)
[ 30.993673@2] dhd_stop: Enter ffffffc052ca5000
[ 30.998035@2] wl_android_wifi_off in 1
[ 31.002062@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 31.006573@2] wl_android_wifi_off out
[ 31.010482@2] dhd_stop: Exit
[ 31.014344@2] dhd_open: Exit ret=-1
[ 31.021891@2] dhd_open: Enter ffffffc052ca5000
[ 31.025762@2]
[ 31.025762@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 31.025762@2] Compiled in drivers/net/wireless/bcmdhd
[ 31.043917@2] wl_android_wifi_on in 1
[ 31.047695@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 31.052236@2] wifi_platform_set_power = 1
[ 31.056164@2] ======== PULL WL_REG_ON HIGH! ========
[ 31.061129@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 31.268021@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 31.778570@2] sdio_reset_comm():
[ 31.913931@7] sdio: clk 200000000 SDR mode tuning start
[ 31.918925@7] sdio: rx_tuning_result[0] = 10
[ 31.923834@7] sdio: rx_tuning_result[1] = 10
[ 31.928656@6] sdio: rx_tuning_result[2] = 10
[ 31.934248@7] sdio: rx_tuning_result[3] = 10
[ 31.938870@3] sdio: best_win_start =0, best_win_size =4
[ 31.942684@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 31.949981@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 31.956110@3] sdioh_start: set sd_f2_blocksize 128
[ 31.961256@3]
[ 31.961256@3]
[ 31.961256@3] dhd_bus_devreset: == WLAN ON ==
[ 31.974353@3] F1 signature read @0x18000000=0x15264345
[ 31.982804@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 31.988133@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 31.994903@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 31.999853@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 32.007719@3] dhd_conf_read_config: PM = 0
[ 32.011760@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 32.020492@3] dhdsdio_download_firmware: set use_rxchain 0
[ 32.025843@3] dhdsdio_download_firmware: set txglomsize 40
[ 32.031343@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 32.036796@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 32.043085@3] Final nv_path=/lib/firmware/brcm/
[ 32.047489@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 32.053609@3] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 32.062762@3] _dhdsdio_download_firmware: dongle image file download failed
[ 32.069702@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 32.074921@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 32.081034@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 32.086384@3] wifi_platform_set_power = 0
[ 32.090334@3] ======== PULL WL_REG_ON LOW! ========
[ 32.095100@3] wl_android_wifi_on: Failed
[ 32.099077@3] dhd_open : wl_android_wifi_on failed (-35)
[ 32.104246@3] dhd_stop: Enter ffffffc052ca5000
[ 32.108707@3] wl_android_wifi_off in 1
[ 32.112654@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 32.117178@3] wl_android_wifi_off out
[ 32.121090@3] dhd_stop: Exit
[ 32.125590@3] dhd_open: Exit ret=-1
[ 32.130694@3] dhd_open: Enter ffffffc052ca5000
[ 32.134564@3]
[ 32.134564@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 32.134564@3] Compiled in drivers/net/wireless/bcmdhd
[ 32.152698@3] wl_android_wifi_on in 1
[ 32.156476@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 32.161054@3] wifi_platform_set_power = 1
[ 32.164944@3] ======== PULL WL_REG_ON HIGH! ========
[ 32.169967@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 32.376808@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 32.888592@3] sdio_reset_comm():
[ 32.920712@5] sdio_read_cis: 10 callbacks suppressed
[ 32.925449@5] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 32.933010@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 32.940240@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 32.949713@0] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 33.047521@4] sdio: clk 200000000 SDR mode tuning start
[ 33.052382@4] sdio: rx_tuning_result[0] = 10
[ 33.057162@4] sdio: rx_tuning_result[1] = 10
[ 33.061808@4] sdio: rx_tuning_result[2] = 10
[ 33.066411@2] sdio: rx_tuning_result[3] = 10
[ 33.069994@2] sdio: best_win_start =0, best_win_size =4
[ 33.074090@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 33.081488@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 33.087623@2] sdioh_start: set sd_f2_blocksize 128
[ 33.092758@2]
[ 33.092758@2]
[ 33.092758@2] dhd_bus_devreset: == WLAN ON ==
[ 33.104862@2] F1 signature read @0x18000000=0x15264345
[ 33.113560@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 33.118607@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 33.125292@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 33.130281@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 33.138172@2] dhd_conf_read_config: PM = 0
[ 33.142191@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 33.150898@2] dhdsdio_download_firmware: set use_rxchain 0
[ 33.156296@2] dhdsdio_download_firmware: set txglomsize 40
[ 33.161752@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 33.167249@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 33.173522@2] Final nv_path=/lib/firmware/brcm/
[ 33.177943@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 33.184052@2] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 33.193163@2] _dhdsdio_download_firmware: dongle image file download failed
[ 33.200133@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 33.205373@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 33.211463@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 33.216843@2] wifi_platform_set_power = 0
[ 33.220766@2] ======== PULL WL_REG_ON LOW! ========
[ 33.225553@2] wl_android_wifi_on: Failed
[ 33.229497@2] dhd_open : wl_android_wifi_on failed (-35)
[ 33.234700@2] dhd_stop: Enter ffffffc052ca5000
[ 33.239125@2] wl_android_wifi_off in 1
[ 33.242940@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 33.247630@2] wl_android_wifi_off out
[ 33.251387@2] dhd_stop: Exit
[ 33.255046@2] dhd_open: Exit ret=-1
[ 33.261827@2] dhd_open: Enter ffffffc052ca5000
[ 33.265473@2]
[ 33.265473@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 33.265473@2] Compiled in drivers/net/wireless/bcmdhd
[ 33.283403@2] wl_android_wifi_on in 1
[ 33.287184@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 33.291799@2] wifi_platform_set_power = 1
[ 33.295683@2] ======== PULL WL_REG_ON HIGH! ========
[ 33.300669@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 33.507535@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 34.018567@2] sdio_reset_comm():
[ 34.050672@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 34.058016@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 34.065991@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 34.075301@7] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 34.173580@7] sdio: clk 200000000 SDR mode tuning start
[ 34.179165@7] sdio: rx_tuning_result[0] = 10
[ 34.183952@7] sdio: rx_tuning_result[1] = 10
[ 34.188647@6] sdio: rx_tuning_result[2] = 10
[ 34.193345@0] sdio: rx_tuning_result[3] = 10
[ 34.196911@0] sdio: best_win_start =0, best_win_size =4
[ 34.201111@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 34.208394@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 34.214588@0] sdioh_start: set sd_f2_blocksize 128
[ 34.219683@0]
[ 34.219683@0]
[ 34.219683@0] dhd_bus_devreset: == WLAN ON ==
[ 34.231908@0] F1 signature read @0x18000000=0x15264345
[ 34.240539@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 34.245684@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 34.252493@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 34.257391@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 34.265308@0] dhd_conf_read_config: PM = 0
[ 34.269268@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 34.278002@0] dhdsdio_download_firmware: set use_rxchain 0
[ 34.283438@0] dhdsdio_download_firmware: set txglomsize 40
[ 34.288888@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 34.294345@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 34.300624@0] Final nv_path=/lib/firmware/brcm/
[ 34.305088@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 34.311169@0] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 34.320267@0] _dhdsdio_download_firmware: dongle image file download failed
[ 34.327352@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 34.332493@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 34.338585@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 34.343915@0] wifi_platform_set_power = 0
[ 34.347810@0] ======== PULL WL_REG_ON LOW! ========
[ 34.352686@0] wl_android_wifi_on: Failed
[ 34.356571@0] dhd_open : wl_android_wifi_on failed (-35)
[ 34.361826@0] dhd_stop: Enter ffffffc052ca5000
[ 34.366181@0] wl_android_wifi_off in 1
[ 34.370012@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 34.374768@0] wl_android_wifi_off out
[ 34.378468@0] dhd_stop: Exit
[ 34.382170@0] dhd_open: Exit ret=-1
[ 34.386383@0] dhd_open: Enter ffffffc052ca5000
[ 34.390672@0]
[ 34.390672@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 34.390672@0] Compiled in drivers/net/wireless/bcmdhd
[ 34.408606@0] wl_android_wifi_on in 1
[ 34.412379@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 34.416891@0] wifi_platform_set_power = 1
[ 34.420893@0] ======== PULL WL_REG_ON HIGH! ========
[ 34.425846@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 34.632751@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 35.138572@2] sdio_reset_comm():
[ 35.170722@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 35.178808@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 35.284380@7] sdio: clk 200000000 SDR mode tuning start
[ 35.289305@7] sdio: rx_tuning_result[0] = 10
[ 35.294251@7] sdio: rx_tuning_result[1] = 10
[ 35.299169@4] sdio: rx_tuning_result[2] = 10
[ 35.304057@2] sdio: rx_tuning_result[3] = 10
[ 35.307821@2] sdio: best_win_start =0, best_win_size =4
[ 35.311777@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 35.319092@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 35.325272@2] sdioh_start: set sd_f2_blocksize 128
[ 35.330408@2]
[ 35.330408@2]
[ 35.330408@2] dhd_bus_devreset: == WLAN ON ==
[ 35.342937@2] F1 signature read @0x18000000=0x15264345
[ 35.351454@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 35.356628@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 35.363365@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 35.368301@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 35.376236@2] dhd_conf_read_config: PM = 0
[ 35.380201@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 35.388944@2] dhdsdio_download_firmware: set use_rxchain 0
[ 35.394347@2] dhdsdio_download_firmware: set txglomsize 40
[ 35.399794@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 35.405301@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 35.411523@2] Final nv_path=/lib/firmware/brcm/
[ 35.415996@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 35.422085@2] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 35.431201@2] _dhdsdio_download_firmware: dongle image file download failed
[ 35.438113@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 35.443446@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 35.449492@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 35.454866@2] wifi_platform_set_power = 0
[ 35.458797@2] ======== PULL WL_REG_ON LOW! ========
[ 35.463606@2] wl_android_wifi_on: Failed
[ 35.467489@2] dhd_open : wl_android_wifi_on failed (-35)
[ 35.472762@2] dhd_stop: Enter ffffffc052ca5000
[ 35.477147@2] wl_android_wifi_off in 1
[ 35.481036@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 35.485685@2] wl_android_wifi_off out
[ 35.489527@2] dhd_stop: Exit
[ 35.493317@2] dhd_open: Exit ret=-1
[ 35.500121@2] dhd_open: Enter ffffffc052ca5000
[ 35.503945@2]
[ 35.503945@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 35.503945@2] Compiled in drivers/net/wireless/bcmdhd
[ 35.521963@2] wl_android_wifi_on in 1
[ 35.525746@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 35.530286@2] wifi_platform_set_power = 1
[ 35.534228@2] ======== PULL WL_REG_ON HIGH! ========
[ 35.539189@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 35.746068@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 36.258546@2] sdio_reset_comm():
[ 36.393738@7] sdio: clk 200000000 SDR mode tuning start
[ 36.398736@7] sdio: rx_tuning_result[0] = 10
[ 36.403626@7] sdio: rx_tuning_result[1] = 10
[ 36.408412@7] sdio: rx_tuning_result[2] = 10
[ 36.413246@7] sdio: rx_tuning_result[3] = 10
[ 36.417823@1] sdio: best_win_start =0, best_win_size =4
[ 36.421648@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 36.428912@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 36.435087@1] sdioh_start: set sd_f2_blocksize 128
[ 36.440188@1]
[ 36.440188@1]
[ 36.440188@1] dhd_bus_devreset: == WLAN ON ==
[ 36.453129@1] F1 signature read @0x18000000=0x15264345
[ 36.461705@1] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 36.466963@1] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 36.473694@1] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 36.478688@1] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 36.486582@1] dhd_conf_read_config: PM = 0
[ 36.490877@1] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 36.499293@1] dhdsdio_download_firmware: set use_rxchain 0
[ 36.504712@1] dhdsdio_download_firmware: set txglomsize 40
[ 36.510159@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 36.515666@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 36.521888@1] Final nv_path=/lib/firmware/brcm/
[ 36.526361@1] Final conf_path=/lib/firmware/brcm/config.txt
[ 36.532416@1] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 36.541566@1] _dhdsdio_download_firmware: dongle image file download failed
[ 36.548477@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 36.553811@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 36.559846@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 36.565231@1] wifi_platform_set_power = 0
[ 36.569161@1] ======== PULL WL_REG_ON LOW! ========
[ 36.573971@1] wl_android_wifi_on: Failed
[ 36.578500@1] dhd_open : wl_android_wifi_on failed (-35)
[ 36.583386@1] dhd_stop: Enter ffffffc052ca5000
[ 36.587991@1] wl_android_wifi_off in 1
[ 36.592557@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 36.597104@1] wl_android_wifi_off out
[ 36.601596@1] dhd_stop: Exit
[ 36.606059@1] dhd_open: Exit ret=-1
[ 36.611102@1] dhd_open: Enter ffffffc052ca5000
[ 36.614950@1]
[ 36.614950@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 36.614950@1] Compiled in drivers/net/wireless/bcmdhd
Debian GNU/Linux 8 amlogic-s905x[ 36.633015@1] wl_android_wifi_on in 1
ttyS0
[ 36.639383@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 36.644972@1] wifi_platform_set_power = 1
[ 36.648962@1] ======== PULL WL_REG_ON HIGH! ========
[ 36.653876@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
amlogic-s905x login: [ 36.860798@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
Debian GNU/Linux 8 amlogic-s905x ttyS0
amlogic-s905x login:
Debian GNU/Linux 8 amlogic-s905x ttyS0
amlogic-s905x login:
Debian GNU/Linux 8 amlogic-s905x ttyS0
amlogic-s905x login: [ 37.368555@1] sdio_reset_comm():
Debian GNU/Linux 8 amlogic-s905x ttyS0
[ 37.503776@7] sdio: clk 200000000 SDR mode tuning start
[ 37.508782@7] sdio: rx_tuning_result[0] = 10
[ 37.513711@7] sdio: rx_tuning_result[1] = 10
[ 37.518482@7] sdio: rx_tuning_result[2] = 10
[ 37.523313@4] sdio: rx_tuning_result[3] = 10
[ 37.527893@0] sdio: best_win_start =0, best_win_size =4
[ 37.531733@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 37.539011@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
amlogic-s905x login: [ 37.545227@0] sdioh_start: set sd_f2_blocksize 128
[ 37.552115@0]
[ 37.552115@0]
[ 37.552115@0] dhd_bus_devreset: == WLAN ON ==
[ 37.565089@0] F1 signature read @0x18000000=0x15264345
[ 37.573823@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 37.579131@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 37.585773@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 37.590810@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 37.598704@0] dhd_conf_read_config: PM = 0
[ 37.602646@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 37.611411@0] dhdsdio_download_firmware: set use_rxchain 0
[ 37.616810@0] dhdsdio_download_firmware: set txglomsize 40
[ 37.622284@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 37.627758@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 37.633988@0] Final nv_path=/lib/firmware/brcm/
[ 37.638480@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 37.644561@0] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 37.653659@0] _dhdsdio_download_firmware: dongle image file download failed
[ 37.660619@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 37.665896@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 37.671961@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 37.677337@0] wifi_platform_set_power = 0
[ 37.681252@0] ======== PULL WL_REG_ON LOW! ========
[ 37.686064@0] wl_android_wifi_on: Failed
[ 37.689991@0] dhd_open : wl_android_wifi_on failed (-35)
[ 37.695208@0] dhd_stop: Enter ffffffc052ca5000
[ 37.699624@0] wl_android_wifi_off in 1
[ 37.703545@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 37.708164@0] wl_android_wifi_off out
[ 37.712016@0] dhd_stop: Exit
[ 37.715856@0] dhd_open: Exit ret=-1
[ 37.722696@0] dhd_open: Enter ffffffc052ca5000
[ 37.726551@0]
[ 37.726551@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 37.726551@0] Compiled in drivers/net/wireless/bcmdhd
[ 37.744672@0] wl_android_wifi_on in 1
[ 37.748424@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 37.752972@0] wifi_platform_set_power = 1
[ 37.756942@0] ======== PULL WL_REG_ON HIGH! ========
[ 37.761874@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 37.968776@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
Debian GNU/Linux 8 amlogic-s905x ttyS0
amlogic-s905x login: [ 38.478563@0] sdio_reset_comm():
[ 38.511218@7] sdio_read_cis: 10 callbacks suppressed
[ 38.515896@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 38.523471@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 38.530716@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 38.540098@3] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 38.637729@4] sdio: clk 200000000 SDR mode tuning start
[ 38.642616@4] sdio: rx_tuning_result[0] = 10
[ 38.647396@4] sdio: rx_tuning_result[1] = 10
[ 38.652083@6] sdio: rx_tuning_result[2] = 10
[ 38.656667@2] sdio: rx_tuning_result[3] = 10
[ 38.660212@2] sdio: best_win_start =0, best_win_size =4
[ 38.664378@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 38.671738@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 38.677905@2] sdioh_start: set sd_f2_blocksize 128
[ 38.683011@2]
[ 38.683011@2]
[ 38.683011@2] dhd_bus_devreset: == WLAN ON ==
[ 38.695051@2] F1 signature read @0x18000000=0x15264345
[ 38.703767@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 38.708745@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 38.715409@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 38.720421@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 38.728315@2] dhd_conf_read_config: PM = 0
[ 38.732314@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 38.741027@2] dhdsdio_download_firmware: set use_rxchain 0
[ 38.746445@2] dhdsdio_download_firmware: set txglomsize 40
[ 38.751891@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 38.757398@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 38.763632@2] Final nv_path=/lib/firmware/brcm/
[ 38.768093@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 38.774140@2] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 38.783295@2] _dhdsdio_download_firmware: dongle image file download failed
[ 38.790252@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 38.795523@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 38.801585@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 38.806969@2] wifi_platform_set_power = 0
[ 38.810895@2] ======== PULL WL_REG_ON LOW! ========
[ 38.815704@2] wl_android_wifi_on: Failed
[ 38.819613@2] dhd_open : wl_android_wifi_on failed (-35)
[ 38.824848@2] dhd_stop: Enter ffffffc052ca5000
[ 38.829519@2] wl_android_wifi_off in 1
[ 38.833306@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 38.838041@2] wl_android_wifi_off out
[ 38.841757@2] dhd_stop: Exit
[ 38.845379@2] dhd_open: Exit ret=-1
[ 38.849595@2] dhd_open: Enter ffffffc052ca5000
Debian GNU/Linux 8 amlogic-s905x ttyS0
[ 38.853231@2]
[ 38.853231@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 38.853231@2] Compiled in drivers/net/wireless/bcmdhd
[ 38.871097@2] wl_android_wifi_on in 1
[ 38.874846@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 38.879474@2] wifi_platform_set_power = 1
[ 38.883401@2] ======== PULL WL_REG_ON HIGH! ========
[ 38.888336@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
amlogic-s905x login:
Debian GNU/Linux 8 amlogic-s905x ttyS0
[ 39.095258@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
amlogic-s905x login:
Debian GNU/Linux 8 amlogic-s905x ttyS0
amlogic-s905x login:
Debian GNU/Linux 8 amlogic-s905x ttyS0
amlogic-s905x login: [ 39.608546@2] sdio_reset_comm():
[ 39.640591@5] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 39.647934@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 39.655188@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 39.664498@5] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
Debian GNU/Linux 8 amlogic-s905x ttyS0
amlogic-s905x login: [ 39.762597@7] sdio: clk 200000000 SDR mode tuning start
[ 39.767435@7] sdio: rx_tuning_result[0] = 10
[ 39.772245@5] sdio: rx_tuning_result[1] = 10
[ 39.776998@7] sdio: rx_tuning_result[2] = 10
[ 39.781711@0] sdio: rx_tuning_result[3] = 10
[ 39.785250@0] sdio: best_win_start =0, best_win_size =4
[ 39.789414@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 39.796679@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 39.802907@0] sdioh_start: set sd_f2_blocksize 128
[ 39.807978@0]
[ 39.807978@0]
[ 39.807978@0] dhd_bus_devreset: == WLAN ON ==
[ 39.820098@0] F1 signature read @0x18000000=0x15264345
[ 39.828662@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 39.833738@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 39.840476@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 39.845410@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 39.853368@0] dhd_conf_read_config: PM = 0
[ 39.857319@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 39.866037@0] dhdsdio_download_firmware: set use_rxchain 0
[ 39.871469@0] dhdsdio_download_firmware: set txglomsize 40
[ 39.876905@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 39.882422@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 39.888653@0] Final nv_path=/lib/firmware/brcm/
[ 39.893097@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 39.899180@0] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 39.908308@0] _dhdsdio_download_firmware: dongle image file download failed
[ 39.915244@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 39.920545@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 39.926593@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 39.932018@0] wifi_platform_set_power = 0
[ 39.935878@0] ======== PULL WL_REG_ON LOW! ========
[ 39.940755@0] wl_android_wifi_on: Failed
[ 39.944595@0] dhd_open : wl_android_wifi_on failed (-35)
[ 39.949869@0] dhd_stop: Enter ffffffc052ca5000
[ 39.954254@0] wl_android_wifi_off in 1
[ 39.958069@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 39.962891@0] wl_android_wifi_off out
[ 39.966568@0] dhd_stop: Exit
[ 39.970251@0] dhd_open: Exit ret=-1
[ 39.976876@0] dhd_open: Enter ffffffc052ca5000
Debian GNU/Linux 8 amlogic-s905x ttyS0
[ 39.980560@0]
[ 39.980560@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 39.980560@0] Compiled in drivers/net/wireless/bcmdhd
[ 39.999210@0] wl_android_wifi_on in 1
[ 40.002955@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 40.007503@0] wifi_platform_set_power = 1
[ 40.011472@0] ======== PULL WL_REG_ON HIGH! ========
[ 40.016377@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
amlogic-s905x login:
Debian GNU/Linux 8 amlogic-s905x ttyS0
amlogic-s905x login:
Debian GNU/Linux 8 amlogic-s905x ttyS0
amlogic-s905x login: [ 40.223334@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
Debian GNU/Linux 8 amlogic-s905x ttyS0
amlogic-s905x login:
Debian GNU/Linux 8 amlogic-s905x ttyS0
amlogic-s905x login:
Debian GNU/Linux 8 amlogic-s905x ttyS0
amlogic-s905x login: [ 40.728555@0] sdio_reset_comm():
[ 40.760588@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 40.767910@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
Debian GNU/Linux 8 amlogic-s905x ttyS0
[ 40.873180@4] sdio: clk 200000000 SDR mode tuning start
[ 40.878038@4] sdio: rx_tuning_result[0] = 10
[ 40.882976@4] sdio: rx_tuning_result[1] = 10
[ 40.887864@4] sdio: rx_tuning_result[2] = 10
[ 40.892665@4] sdio: rx_tuning_result[3] = 10
[ 40.897160@2] sdio: best_win_start =0, best_win_size =4
[ 40.900929@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 40.908234@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 40.914440@2] sdioh_start: set sd_f2_blocksize 128
amlogic-s905x login: [ 40.919557@2]
[ 40.919557@2]
[ 40.919557@2] dhd_bus_devreset: == WLAN ON ==
[ 40.932074@2] F1 signature read @0x18000000=0x15264345
[ 40.940544@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 40.945689@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 40.952410@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 40.957388@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 40.965321@2] dhd_conf_read_config: PM = 0
[ 40.969285@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 40.978001@2] dhdsdio_download_firmware: set use_rxchain 0
[ 40.983462@2] dhdsdio_download_firmware: set txglomsize 40
[ 40.988881@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 40.994387@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 41.000620@2] Final nv_path=/lib/firmware/brcm/
[ 41.005340@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 41.011418@2] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 41.020543@2] _dhdsdio_download_firmware: dongle image file download failed
[ 41.027462@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 41.032791@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 41.038836@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 41.044211@2] wifi_platform_set_power = 0
[ 41.048120@2] ======== PULL WL_REG_ON LOW! ========
[ 41.052971@2] wl_android_wifi_on: Failed
Debian GNU/Linux 8 aml[ 41.056862@2] dhd_open : wl_android_wifi_on failed (-35)
ogic-s905x ttyS0
[ 41.064006@2] dhd_stop: Enter ffffffc052ca5000
[ 41.070138@2] wl_android_wifi_off in 1
[ 41.074010@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 41.078666@2] wl_android_wifi_off out
[ 41.082501@2] dhd_stop: Exit
[ 41.086282@2] dhd_open: Exit ret=-1
[ 41.090589@2] dhd_open: Enter ffffffc052ca5000
[ 41.094994@2]
[ 41.094994@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 41.094994@2] Compiled in drivers/net/wireless/bcmdhd
amlogic-s905x login: [ 41.114794@2] wl_android_wifi_on in 1
[ 41.120191@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 41.124918@2] wifi_platform_set_power = 1
[ 41.128910@2] ======== PULL WL_REG_ON HIGH! ========
[ 41.133821@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 41.340747@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 41.848545@2] sdio_reset_comm():
[ 41.983714@4] sdio: clk 200000000 SDR mode tuning start
[ 41.988684@7] sdio: rx_tuning_result[0] = 10
[ 41.993566@7] sdio: rx_tuning_result[1] = 10
[ 41.998345@7] sdio: rx_tuning_result[2] = 10
[ 42.003182@7] sdio: rx_tuning_result[3] = 10
[ 42.007732@3] sdio: best_win_start =0, best_win_size =4
[ 42.011590@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 42.018890@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 42.025018@3] sdioh_start: set sd_f2_blocksize 128
[ 42.030116@3]
[ 42.030116@3]
[ 42.030116@3] dhd_bus_devreset: == WLAN ON ==
[ 42.043057@3] F1 signature read @0x18000000=0x15264345
[ 42.051478@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 42.056704@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 42.063442@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 42.068408@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 42.076358@3] dhd_conf_read_config: PM = 0
[ 42.080324@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 42.089050@3] dhdsdio_download_firmware: set use_rxchain 0
[ 42.094454@3] dhdsdio_download_firmware: set txglomsize 40
[ 42.099915@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 42.105408@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 42.111645@3] Final nv_path=/lib/firmware/brcm/
[ 42.116103@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 42.122144@3] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 42.131317@3] _dhdsdio_download_firmware: dongle image file download failed
[ 42.138222@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 42.143561@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 42.149600@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 42.154972@3] wifi_platform_set_power = 0
[ 42.158912@3] ======== PULL WL_REG_ON LOW! ========
[ 42.163713@3] wl_android_wifi_on: Failed
[ 42.167594@3] dhd_open : wl_android_wifi_on failed (-35)
[ 42.172882@3] dhd_stop: Enter ffffffc052ca5000
[ 42.177254@3] wl_android_wifi_off in 1
[ 42.181184@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 42.185792@3] wl_android_wifi_off out
[ 42.189637@3] dhd_stop: Exit
[ 42.193462@3] dhd_open: Exit ret=-1
[ 42.200346@3] dhd_open: Enter ffffffc052ca5000
[ 42.204204@3]
[ 42.204204@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 42.204204@3] Compiled in drivers/net/wireless/bcmdhd
[ 42.222306@3] wl_android_wifi_on in 1
[ 42.226047@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 42.230621@3] wifi_platform_set_power = 1
[ 42.234559@3] ======== PULL WL_REG_ON HIGH! ========
[ 42.239524@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 42.446398@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 42.958555@3] sdio_reset_comm():
[ 43.093688@4] sdio: clk 200000000 SDR mode tuning start
[ 43.098672@7] sdio: rx_tuning_result[0] = 10
[ 43.103592@7] sdio: rx_tuning_result[1] = 10
[ 43.108374@7] sdio: rx_tuning_result[2] = 10
[ 43.113216@7] sdio: rx_tuning_result[3] = 10
[ 43.117772@0] sdio: best_win_start =0, best_win_size =4
[ 43.121603@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 43.128896@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 43.135082@0] sdioh_start: set sd_f2_blocksize 128
[ 43.140209@0]
[ 43.140209@0]
[ 43.140209@0] dhd_bus_devreset: == WLAN ON ==
[ 43.153175@0] F1 signature read @0x18000000=0x15264345
[ 43.161897@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 43.167166@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 43.173928@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 43.178864@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 43.186762@0] dhd_conf_read_config: PM = 0
[ 43.190786@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 43.199476@0] dhdsdio_download_firmware: set use_rxchain 0
[ 43.204896@0] dhdsdio_download_firmware: set txglomsize 40
[ 43.210367@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 43.215844@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 43.222089@0] Final nv_path=/lib/firmware/brcm/
[ 43.226544@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 43.232621@0] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 43.241770@0] _dhdsdio_download_firmware: dongle image file download failed
[ 43.248686@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 43.253969@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 43.260048@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 43.265414@0] wifi_platform_set_power = 0
[ 43.269339@0] ======== PULL WL_REG_ON LOW! ========
[ 43.274176@0] wl_android_wifi_on: Failed
[ 43.278076@0] dhd_open : wl_android_wifi_on failed (-35)
[ 43.283310@0] dhd_stop: Enter ffffffc052ca5000
[ 43.287690@0] wl_android_wifi_off in 1
[ 43.291647@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 43.296233@0] wl_android_wifi_off out
[ 43.300081@0] dhd_stop: Exit
[ 43.304042@0] dhd_open: Exit ret=-1
[ 43.308472@0] dhd_open: Enter ffffffc052ca5000
[ 43.312368@0]
[ 43.312368@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 43.312368@0] Compiled in drivers/net/wireless/bcmdhd
[ 43.330481@0] wl_android_wifi_on in 1
[ 43.334234@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 43.338827@0] wifi_platform_set_power = 1
[ 43.343218@0] ======== PULL WL_REG_ON HIGH! ========
[ 43.347732@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 43.554608@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 44.068557@1] sdio_reset_comm():
[ 44.100698@7] sdio_read_cis: 10 callbacks suppressed
[ 44.105520@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 44.113070@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 44.120430@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 44.129944@2] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 44.227620@7] sdio: clk 200000000 SDR mode tuning start
[ 44.232592@7] sdio: rx_tuning_result[0] = 10
[ 44.237487@7] sdio: rx_tuning_result[1] = 10
[ 44.242276@7] sdio: rx_tuning_result[2] = 10
[ 44.246951@3] sdio: rx_tuning_result[3] = 10
[ 44.250606@3] sdio: best_win_start =0, best_win_size =4
[ 44.254681@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 44.262044@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 44.268198@3] sdioh_start: set sd_f2_blocksize 128
[ 44.273298@3]
[ 44.273298@3]
[ 44.273298@3] dhd_bus_devreset: == WLAN ON ==
[ 44.285698@3] F1 signature read @0x18000000=0x15264345
[ 44.294142@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 44.299197@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 44.305881@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 44.310922@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 44.318826@3] dhd_conf_read_config: PM = 0
[ 44.322768@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 44.331525@3] dhdsdio_download_firmware: set use_rxchain 0
[ 44.336928@3] dhdsdio_download_firmware: set txglomsize 40
[ 44.342391@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 44.347882@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 44.354121@3] Final nv_path=/lib/firmware/brcm/
[ 44.358602@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 44.364614@3] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 44.373791@3] _dhdsdio_download_firmware: dongle image file download failed
[ 44.380725@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 44.386007@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 44.392070@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 44.397444@3] wifi_platform_set_power = 0
[ 44.401385@3] ======== PULL WL_REG_ON LOW! ========
[ 44.406187@3] wl_android_wifi_on: Failed
[ 44.410096@3] dhd_open : wl_android_wifi_on failed (-35)
[ 44.415332@3] dhd_stop: Enter ffffffc052ca5000
[ 44.419752@3] wl_android_wifi_off in 1
[ 44.423645@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 44.428265@3] wl_android_wifi_off out
[ 44.431997@3] dhd_stop: Exit
[ 44.435610@3] dhd_open: Exit ret=-1
[ 44.442190@3] dhd_open: Enter ffffffc052ca5000
[ 44.445816@3]
[ 44.445816@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 44.445816@3] Compiled in drivers/net/wireless/bcmdhd
[ 44.463685@3] wl_android_wifi_on in 1
[ 44.467418@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 44.472018@3] wifi_platform_set_power = 1
[ 44.475955@3] ======== PULL WL_REG_ON HIGH! ========
[ 44.480924@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 44.687794@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 45.198564@2] sdio_reset_comm():
[ 45.230743@5] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 45.238205@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 45.245583@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 45.255030@5] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 45.354150@4] sdio: clk 200000000 SDR mode tuning start
[ 45.359163@4] sdio: rx_tuning_result[0] = 10
[ 45.364089@4] sdio: rx_tuning_result[1] = 10
[ 45.368947@4] sdio: rx_tuning_result[2] = 10
[ 45.373693@2] sdio: rx_tuning_result[3] = 10
[ 45.377332@2] sdio: best_win_start =0, best_win_size =4
[ 45.381445@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 45.388760@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 45.394925@2] sdioh_start: set sd_f2_blocksize 128
[ 45.400020@2]
[ 45.400020@2]
[ 45.400020@2] dhd_bus_devreset: == WLAN ON ==
[ 45.412488@2] F1 signature read @0x18000000=0x15264345
[ 45.421108@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 45.426275@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 45.432983@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 45.437963@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 45.445912@2] dhd_conf_read_config: PM = 0
[ 45.449863@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 45.458589@2] dhdsdio_download_firmware: set use_rxchain 0
[ 45.464009@2] dhdsdio_download_firmware: set txglomsize 40
[ 45.469466@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 45.474962@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 45.481185@2] Final nv_path=/lib/firmware/brcm/
[ 45.485657@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 45.491691@2] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 45.500872@2] _dhdsdio_download_firmware: dongle image file download failed
[ 45.507775@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 45.513105@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 45.519139@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 45.524528@2] wifi_platform_set_power = 0
[ 45.528436@2] ======== PULL WL_REG_ON LOW! ========
[ 45.533297@2] wl_android_wifi_on: Failed
[ 45.537164@2] dhd_open : wl_android_wifi_on failed (-35)
[ 45.542424@2] dhd_stop: Enter ffffffc052ca5000
[ 45.546809@2] wl_android_wifi_off in 1
[ 45.550719@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 45.555347@2] wl_android_wifi_off out
[ 45.559150@2] dhd_stop: Exit
[ 45.562832@2] dhd_open: Exit ret=-1
[ 45.567034@2] dhd_open: Enter ffffffc052ca5000
[ 45.570680@2]
[ 45.570680@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 45.570680@2] Compiled in drivers/net/wireless/bcmdhd
[ 45.588502@2] wl_android_wifi_on in 1
[ 45.592280@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 45.596851@2] wifi_platform_set_power = 1
[ 45.600838@2] ======== PULL WL_REG_ON HIGH! ========
[ 45.605754@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 45.812682@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 46.318545@2] sdio_reset_comm():
[ 46.350739@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 46.358224@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 46.463697@4] sdio: clk 200000000 SDR mode tuning start
[ 46.468794@7] sdio: rx_tuning_result[0] = 10
[ 46.474749@7] sdio: rx_tuning_result[1] = 10
[ 46.480094@7] sdio: rx_tuning_result[2] = 10
[ 46.486010@3] sdio: rx_tuning_result[3] = 10
[ 46.490135@3] sdio: best_win_start =0, best_win_size =4
[ 46.494146@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 46.501206@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 46.507362@3] sdioh_start: set sd_f2_blocksize 128
[ 46.512464@3]
[ 46.512464@3]
[ 46.512464@3] dhd_bus_devreset: == WLAN ON ==
[ 46.526012@3] F1 signature read @0x18000000=0x15264345
[ 46.534472@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 46.540062@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 46.546728@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 46.551762@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 46.559672@3] dhd_conf_read_config: PM = 0
[ 46.563612@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 46.572367@3] dhdsdio_download_firmware: set use_rxchain 0
[ 46.577772@3] dhdsdio_download_firmware: set txglomsize 40
[ 46.583231@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 46.588754@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 46.594935@3] Final nv_path=/lib/firmware/brcm/
[ 46.599448@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 46.605464@3] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 46.614642@3] _dhdsdio_download_firmware: dongle image file download failed
[ 46.621574@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 46.626851@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 46.632918@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 46.638299@3] wifi_platform_set_power = 0
[ 46.642726@3] ======== PULL WL_REG_ON LOW! ========
[ 46.642731@3] wl_android_wifi_on: Failed
[ 46.642734@3] dhd_open : wl_android_wifi_on failed (-35)
[ 46.642737@3] dhd_stop: Enter ffffffc052ca5000
[ 46.642739@3] wl_android_wifi_off in 1
[ 46.642741@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 46.642742@3] wl_android_wifi_off out
[ 46.642743@3] dhd_stop: Exit
[ 46.642746@3] dhd_open: Exit ret=-1
[ 46.645697@3] dhd_open: Enter ffffffc052ca5000
[ 46.645705@3]
[ 46.645705@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 46.645705@3] Compiled in drivers/net/wireless/bcmdhd
[ 46.645707@3] wl_android_wifi_on in 1
[ 46.645709@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 46.645712@3] wifi_platform_set_power = 1
[ 46.645713@3] ======== PULL WL_REG_ON HIGH! ========
[ 46.645736@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 46.845766@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 47.358557@3] sdio_reset_comm():
[ 47.494929@7] sdio: clk 200000000 SDR mode tuning start
[ 47.500362@7] sdio: rx_tuning_result[0] = 10
[ 47.506497@7] sdio: rx_tuning_result[1] = 10
[ 47.511808@4] sdio: rx_tuning_result[2] = 10
[ 47.517159@3] sdio: rx_tuning_result[3] = 10
[ 47.521454@3] sdio: best_win_start =0, best_win_size =4
[ 47.525583@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 47.532540@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 47.538715@3] sdioh_start: set sd_f2_blocksize 128
[ 47.543730@3]
[ 47.543730@3]
[ 47.543730@3] dhd_bus_devreset: == WLAN ON ==
[ 47.557393@3] F1 signature read @0x18000000=0x15264345
[ 47.565678@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 47.571133@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 47.577818@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 47.582869@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 47.590760@3] dhd_conf_read_config: PM = 0
[ 47.594696@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 47.603457@3] dhdsdio_download_firmware: set use_rxchain 0
[ 47.608883@3] dhdsdio_download_firmware: set txglomsize 40
[ 47.614291@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 47.619846@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 47.626021@3] Final nv_path=/lib/firmware/brcm/
[ 47.630534@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 47.636561@3] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 47.645723@3] _dhdsdio_download_firmware: dongle image file download failed
[ 47.652655@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 47.657935@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 47.664001@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 47.669410@3] wifi_platform_set_power = 0
[ 47.673986@3] ======== PULL WL_REG_ON LOW! ========
[ 47.678668@3] wl_android_wifi_on: Failed
[ 47.683355@3] dhd_open : wl_android_wifi_on failed (-35)
[ 47.688122@3] dhd_stop: Enter ffffffc052ca5000
[ 47.692916@3] wl_android_wifi_off in 1
[ 47.697636@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 47.701692@3] wl_android_wifi_off out
[ 47.705673@3] dhd_stop: Exit
[ 47.709776@3] dhd_open: Exit ret=-1
[ 47.714377@3] dhd_open: Enter ffffffc052ca5000
[ 47.718418@3]
[ 47.718418@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 47.718418@3] Compiled in drivers/net/wireless/bcmdhd
[ 47.736785@3] wl_android_wifi_on in 1
[ 47.740664@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 47.745072@3] wifi_platform_set_power = 1
[ 47.749117@3] ======== PULL WL_REG_ON HIGH! ========
[ 47.753984@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 47.961020@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 48.468565@3] sdio_reset_comm():
[ 48.604259@4] sdio: clk 200000000 SDR mode tuning start
[ 48.609478@4] sdio: rx_tuning_result[0] = 10
[ 48.615192@4] sdio: rx_tuning_result[1] = 10
[ 48.620338@4] sdio: rx_tuning_result[2] = 10
[ 48.625284@3] sdio: rx_tuning_result[3] = 10
[ 48.629196@3] sdio: best_win_start =0, best_win_size =4
[ 48.633047@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 48.640361@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 48.646521@3] sdioh_start: set sd_f2_blocksize 128
[ 48.651623@3]
[ 48.651623@3]
[ 48.651623@3] dhd_bus_devreset: == WLAN ON ==
[ 48.664745@3] F1 signature read @0x18000000=0x15264345
[ 48.673268@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 48.678620@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 48.685292@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 48.690324@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 48.698203@3] dhd_conf_read_config: PM = 0
[ 48.702200@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 48.710926@3] dhdsdio_download_firmware: set use_rxchain 0
[ 48.716332@3] dhdsdio_download_firmware: set txglomsize 40
[ 48.721791@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 48.727286@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 48.733520@3] Final nv_path=/lib/firmware/brcm/
[ 48.737981@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 48.744029@3] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 48.753207@3] _dhdsdio_download_firmware: dongle image file download failed
[ 48.760145@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 48.765410@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 48.771478@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 48.776859@3] wifi_platform_set_power = 0
[ 48.780814@3] ======== PULL WL_REG_ON LOW! ========
[ 48.785591@3] wl_android_wifi_on: Failed
[ 48.789619@3] dhd_open : wl_android_wifi_on failed (-35)
[ 48.794736@3] dhd_stop: Enter ffffffc052ca5000
[ 48.799156@3] wl_android_wifi_off in 1
[ 48.803184@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 48.807670@3] wl_android_wifi_off out
[ 48.811633@3] dhd_stop: Exit
[ 48.815576@3] dhd_open: Exit ret=-1
[ 48.822514@3] dhd_open: Enter ffffffc052ca5000
[ 48.826478@3]
[ 48.826478@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 48.826478@3] Compiled in drivers/net/wireless/bcmdhd
[ 48.844894@3] wl_android_wifi_on in 1
[ 48.848749@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 48.853194@3] wifi_platform_set_power = 1
[ 48.857161@3] ======== PULL WL_REG_ON HIGH! ========
[ 48.862131@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 49.069033@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 49.578559@3] sdio_reset_comm():
[ 49.611403@4] sdio_read_cis: 10 callbacks suppressed
[ 49.616292@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 49.623855@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 49.631350@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 49.640994@0] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 49.738920@7] sdio: clk 200000000 SDR mode tuning start
[ 49.743963@7] sdio: rx_tuning_result[0] = 10
[ 49.748975@7] sdio: rx_tuning_result[1] = 10
[ 49.753872@7] sdio: rx_tuning_result[2] = 10
[ 49.758692@2] sdio: rx_tuning_result[3] = 10
[ 49.758723@2] sdio: best_win_start =0, best_win_size =4
[ 49.758730@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 49.758734@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 49.758792@2] sdioh_start: set sd_f2_blocksize 128
[ 49.759194@2]
[ 49.759194@2]
[ 49.759194@2] dhd_bus_devreset: == WLAN ON ==
[ 49.759398@2] F1 signature read @0x18000000=0x15264345
[ 49.806258@7] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 49.806948@7] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 49.807377@7] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 49.807382@7] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 49.807569@7] dhd_conf_read_config: PM = 0
[ 49.807654@7] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 49.807657@7] dhdsdio_download_firmware: set use_rxchain 0
[ 49.807659@7] dhdsdio_download_firmware: set txglomsize 40
[ 49.807661@7] sdioh_set_mode: set txglom_mode to multi-desc
[ 49.807663@7] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 49.807665@7] Final nv_path=/lib/firmware/brcm/
[ 49.807666@7] Final conf_path=/lib/firmware/brcm/config.txt
[ 49.808134@4] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 49.808136@4] _dhdsdio_download_firmware: dongle image file download failed
[ 49.808167@4] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 49.808171@4] dhd_prot_ioctl : bus is down. we have nothing to do
[ 49.808174@4] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 49.808223@4] wifi_platform_set_power = 0
[ 49.808225@4] ======== PULL WL_REG_ON LOW! ========
[ 49.808226@4] wl_android_wifi_on: Failed
[ 49.808229@4] dhd_open : wl_android_wifi_on failed (-35)
[ 49.808233@4] dhd_stop: Enter ffffffc052ca5000
[ 49.808235@4] wl_android_wifi_off in 1
[ 49.808237@4] wl_android_wifi_off in 2: g_wifi_on=0
[ 49.808238@4] wl_android_wifi_off out
[ 49.808240@4] dhd_stop: Exit
[ 49.808245@4] dhd_open: Exit ret=-1
[ 49.808982@4] dhd_open: Enter ffffffc052ca5000
[ 49.808990@4]
[ 49.808990@4] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 49.808990@4] Compiled in drivers/net/wireless/bcmdhd
[ 49.808992@4] wl_android_wifi_on in 1
[ 49.808994@4] wl_android_wifi_on in 2: g_wifi_on=0
[ 49.808997@4] wifi_platform_set_power = 1
[ 49.808999@4] ======== PULL WL_REG_ON HIGH! ========
[ 49.809021@4] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 50.009054@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 50.518553@1] sdio_reset_comm():
[ 50.550223@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 50.556210@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 50.558846@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 50.563574@7] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 50.657195@7] sdio: clk 200000000 SDR mode tuning start
[ 50.661505@7] sdio: rx_tuning_result[0] = 10
[ 50.666424@7] sdio: rx_tuning_result[1] = 10
[ 50.670685@7] sdio: rx_tuning_result[2] = 10
[ 50.674855@7] sdio: rx_tuning_result[3] = 10
[ 50.678740@3] sdio: best_win_start =0, best_win_size =4
[ 50.682843@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 50.690214@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 50.696367@3] sdioh_start: set sd_f2_blocksize 128
[ 50.701459@3]
[ 50.701459@3]
[ 50.701459@3] dhd_bus_devreset: == WLAN ON ==
[ 50.713678@3] F1 signature read @0x18000000=0x15264345
[ 50.722196@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 50.727336@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 50.734042@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 50.734046@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 50.734203@3] dhd_conf_read_config: PM = 0
[ 50.734274@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 50.734278@3] dhdsdio_download_firmware: set use_rxchain 0
[ 50.734280@3] dhdsdio_download_firmware: set txglomsize 40
[ 50.734282@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 50.734283@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 50.734285@3] Final nv_path=/lib/firmware/brcm/
[ 50.734286@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 50.734764@3] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 50.734765@3] _dhdsdio_download_firmware: dongle image file download failed
[ 50.734797@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 50.734802@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 50.734804@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 50.734858@3] wifi_platform_set_power = 0
[ 50.734859@3] ======== PULL WL_REG_ON LOW! ========
[ 50.734861@3] wl_android_wifi_on: Failed
[ 50.734864@3] dhd_open : wl_android_wifi_on failed (-35)
[ 50.734867@3] dhd_stop: Enter ffffffc052ca5000
[ 50.734869@3] wl_android_wifi_off in 1
[ 50.734871@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 50.734872@3] wl_android_wifi_off out
[ 50.734874@3] dhd_stop: Exit
[ 50.734878@3] dhd_open: Exit ret=-1
[ 50.737837@3] dhd_open: Enter ffffffc052ca5000
[ 50.737845@3]
[ 50.737845@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 50.737845@3] Compiled in drivers/net/wireless/bcmdhd
[ 50.737847@3] wl_android_wifi_on in 1
[ 50.737849@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 50.737851@3] wifi_platform_set_power = 1
[ 50.737854@3] ======== PULL WL_REG_ON HIGH! ========
[ 50.737875@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 50.937905@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 51.438570@3] sdio_reset_comm():
[ 51.469919@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 51.476963@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 51.511883@3] EXT4-fs (mmcblk1p2): resizing filesystem from 378880 to 1876836 blocks
[ 51.581583@7] sdio: clk 200000000 SDR mode tuning start
[ 51.586255@7] sdio: rx_tuning_result[0] = 10
[ 51.590621@7] sdio: rx_tuning_result[1] = 10
[ 51.594604@7] sdio: rx_tuning_result[2] = 10
[ 51.598480@7] sdio: rx_tuning_result[3] = 10
[ 51.605582@0] sdio: best_win_start =0, best_win_size =4
[ 51.605586@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 51.605590@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 51.605666@0] sdioh_start: set sd_f2_blocksize 128
[ 51.606083@0]
[ 51.606083@0]
[ 51.606083@0] dhd_bus_devreset: == WLAN ON ==
[ 51.606282@0] F1 signature read @0x18000000=0x15264345
[ 51.609915@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 51.610648@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 51.611083@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 51.611086@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 51.611243@0] dhd_conf_read_config: PM = 0
[ 51.611314@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 51.611318@0] dhdsdio_download_firmware: set use_rxchain 0
[ 51.611320@0] dhdsdio_download_firmware: set txglomsize 40
[ 51.611322@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 51.611323@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 51.611324@0] Final nv_path=/lib/firmware/brcm/
[ 51.611326@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 51.611805@0] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 51.611807@0] _dhdsdio_download_firmware: dongle image file download failed
[ 51.611838@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 51.611843@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 51.611845@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 51.611901@0] wifi_platform_set_power = 0
[ 51.611903@0] ======== PULL WL_REG_ON LOW! ========
[ 51.611904@0] wl_android_wifi_on: Failed
[ 51.611907@0] dhd_open : wl_android_wifi_on failed (-35)
[ 51.611911@0] dhd_stop: Enter ffffffc052ca5000
[ 51.611913@0] wl_android_wifi_off in 1
[ 51.611915@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 51.611916@0] wl_android_wifi_off out
[ 51.611917@0] dhd_stop: Exit
[ 51.611921@0] dhd_open: Exit ret=-1
[ 51.612516@0] dhd_open: Enter ffffffc052ca5000
[ 51.612522@0]
[ 51.612522@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 51.612522@0] Compiled in drivers/net/wireless/bcmdhd
[ 51.612524@0] wl_android_wifi_on in 1
[ 51.612527@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 51.612529@0] wifi_platform_set_power = 1
[ 51.612530@0] ======== PULL WL_REG_ON HIGH! ========
[ 51.612553@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 51.828553@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 52.338560@0] sdio_reset_comm():
[ 52.473349@7] sdio: clk 200000000 SDR mode tuning start
[ 52.477424@7] sdio: rx_tuning_result[0] = 10
[ 52.481345@7] sdio: rx_tuning_result[1] = 10
[ 52.485438@7] sdio: rx_tuning_result[2] = 10
[ 52.489669@7] sdio: rx_tuning_result[3] = 10
[ 52.493663@7] sdio: best_win_start =0, best_win_size =4
[ 52.501655@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 52.501661@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 52.501755@0] sdioh_start: set sd_f2_blocksize 128
[ 52.502211@0]
[ 52.502211@0]
[ 52.502211@0] dhd_bus_devreset: == WLAN ON ==
[ 52.502430@0] F1 signature read @0x18000000=0x15264345
[ 52.506371@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 52.507166@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 52.507623@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 52.507626@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 52.507783@0] dhd_conf_read_config: PM = 0
[ 52.507854@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 52.507858@0] dhdsdio_download_firmware: set use_rxchain 0
[ 52.507859@0] dhdsdio_download_firmware: set txglomsize 40
[ 52.507861@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 52.507863@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 52.507864@0] Final nv_path=/lib/firmware/brcm/
[ 52.507865@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 52.508386@0] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 52.508388@0] _dhdsdio_download_firmware: dongle image file download failed
[ 52.508421@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 52.508426@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 52.508428@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 52.508486@0] wifi_platform_set_power = 0
[ 52.508489@0] ======== PULL WL_REG_ON LOW! ========
[ 52.508490@0] wl_android_wifi_on: Failed
[ 52.508493@0] dhd_open : wl_android_wifi_on failed (-35)
[ 52.508497@0] dhd_stop: Enter ffffffc052ca5000
[ 52.508499@0] wl_android_wifi_off in 1
[ 52.508501@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 52.508502@0] wl_android_wifi_off out
[ 52.508503@0] dhd_stop: Exit
[ 52.508508@0] dhd_open: Exit ret=-1
[ 52.511542@0] dhd_open: Enter ffffffc052ca5000
[ 52.511551@0]
[ 52.511551@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 52.511551@0] Compiled in drivers/net/wireless/bcmdhd
[ 52.511553@0] wl_android_wifi_on in 1
[ 52.511555@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 52.511557@0] wifi_platform_set_power = 1
[ 52.511559@0] ======== PULL WL_REG_ON HIGH! ========
[ 52.511581@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 52.711611@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 52.887141@4] EXT4-fs (mmcblk1p2): resized filesystem to 1876836
[ 53.218554@1] sdio_reset_comm():
[ 53.354265@7] sdio: clk 200000000 SDR mode tuning start
[ 53.359310@7] sdio: rx_tuning_result[0] = 10
[ 53.364282@7] sdio: rx_tuning_result[1] = 10
[ 53.369196@7] sdio: rx_tuning_result[2] = 10
[ 53.373997@7] sdio: rx_tuning_result[3] = 10
[ 53.378458@2] sdio: best_win_start =0, best_win_size =4
[ 53.382226@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 53.389560@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 53.395724@2] sdioh_start: set sd_f2_blocksize 128
[ 53.400833@2]
[ 53.400833@2]
[ 53.400833@2] dhd_bus_devreset: == WLAN ON ==
[ 53.413490@2] F1 signature read @0x18000000=0x15264345
[ 53.422098@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 53.427345@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 53.434079@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 53.439067@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 53.446963@2] dhd_conf_read_config: PM = 0
[ 53.450964@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 53.459676@2] dhdsdio_download_firmware: set use_rxchain 0
[ 53.465094@2] dhdsdio_download_firmware: set txglomsize 40
[ 53.470540@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 53.476047@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 53.482280@2] Final nv_path=/lib/firmware/brcm/
[ 53.486742@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 53.492796@2] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 53.501946@2] _dhdsdio_download_firmware: dongle image file download failed
[ 53.508886@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 53.514172@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 53.520229@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 53.525613@2] wifi_platform_set_power = 0
[ 53.529662@2] ======== PULL WL_REG_ON LOW! ========
[ 53.534352@2] wl_android_wifi_on: Failed
[ 53.538386@2] dhd_open : wl_android_wifi_on failed (-35)
[ 53.543521@2] dhd_stop: Enter ffffffc052ca5000
[ 53.547894@2] wl_android_wifi_off in 1
[ 53.551987@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 53.556431@2] wl_android_wifi_off out
[ 53.560457@2] dhd_stop: Exit
[ 53.564399@2] dhd_open: Exit ret=-1
[ 53.568998@2] dhd_open: Enter ffffffc052ca5000
[ 53.572934@2]
[ 53.572934@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 53.572934@2] Compiled in drivers/net/wireless/bcmdhd
[ 53.591150@2] wl_android_wifi_on in 1
[ 53.595495@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 53.599863@2] wifi_platform_set_power = 1
[ 53.604244@2] ======== PULL WL_REG_ON HIGH! ========
[ 53.608767@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 53.815310@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 54.328579@1] sdio_reset_comm():
[ 54.464412@7] sdio: clk 200000000 SDR mode tuning start
[ 54.469441@7] sdio: rx_tuning_result[0] = 10
[ 54.475065@7] sdio: rx_tuning_result[1] = 10
[ 54.479882@7] sdio: rx_tuning_result[2] = 10
[ 54.484710@7] sdio: rx_tuning_result[3] = 10
[ 54.489283@3] sdio: best_win_start =0, best_win_size =4
[ 54.493091@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 54.500429@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 54.506542@3] sdioh_start: set sd_f2_blocksize 128
[ 54.511638@3]
[ 54.511638@3]
[ 54.511638@3] dhd_bus_devreset: == WLAN ON ==
[ 54.524698@3] F1 signature read @0x18000000=0x15264345
[ 54.533080@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 54.538398@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 54.545074@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 54.550143@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 54.557962@3] dhd_conf_read_config: PM = 0
[ 54.562005@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 54.570732@3] dhdsdio_download_firmware: set use_rxchain 0
[ 54.576083@3] dhdsdio_download_firmware: set txglomsize 40
[ 54.581578@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 54.587034@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 54.593274@3] Final nv_path=/lib/firmware/brcm/
[ 54.597729@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 54.603808@3] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 54.612943@3] _dhdsdio_download_firmware: dongle image file download failed
[ 54.619895@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 54.625158@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 54.631225@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 54.636607@3] wifi_platform_set_power = 0
[ 54.640541@3] ======== PULL WL_REG_ON LOW! ========
[ 54.645339@3] wl_android_wifi_on: Failed
[ 54.649268@3] dhd_open : wl_android_wifi_on failed (-35)
[ 54.654483@3] dhd_stop: Enter ffffffc052ca5000
[ 54.658907@3] wl_android_wifi_off in 1
[ 54.662835@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 54.667417@3] wl_android_wifi_off out
[ 54.671286@3] dhd_stop: Exit
[ 54.675137@3] dhd_open: Exit ret=-1
[ 54.681995@3] dhd_open: Enter ffffffc052ca5000
[ 54.685869@3]
[ 54.685869@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 54.685869@3] Compiled in drivers/net/wireless/bcmdhd
[ 54.704000@3] wl_android_wifi_on in 1
[ 54.707752@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 54.712324@3] wifi_platform_set_power = 1
[ 54.716262@3] ======== PULL WL_REG_ON HIGH! ========
[ 54.721222@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 54.928098@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 55.438614@0] sdio_reset_comm():
[ 55.471042@5] sdio_read_cis: 14 callbacks suppressed
[ 55.475809@5] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 55.483439@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 55.491600@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 55.502440@2] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 55.600863@5] sdio: clk 200000000 SDR mode tuning start
[ 55.605822@5] sdio: rx_tuning_result[0] = 10
[ 55.611024@5] sdio: rx_tuning_result[1] = 10
[ 55.615760@5] sdio: rx_tuning_result[2] = 10
[ 55.620514@0] sdio: rx_tuning_result[3] = 10
[ 55.624158@0] sdio: best_win_start =0, best_win_size =4
[ 55.628079@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 55.635472@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 55.641705@0] sdioh_start: set sd_f2_blocksize 128
[ 55.646725@0]
[ 55.646725@0]
[ 55.646725@0] dhd_bus_devreset: == WLAN ON ==
[ 55.658918@0] F1 signature read @0x18000000=0x15264345
[ 55.667452@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 55.672620@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 55.679273@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 55.684148@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 55.692138@0] dhd_conf_read_config: PM = 0
[ 55.696033@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 55.704808@0] dhdsdio_download_firmware: set use_rxchain 0
[ 55.710279@0] dhdsdio_download_firmware: set txglomsize 40
[ 55.715626@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 55.721175@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 55.727409@0] Final nv_path=/lib/firmware/brcm/
[ 55.731875@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 55.737922@0] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 55.747128@0] _dhdsdio_download_firmware: dongle image file download failed
[ 55.754045@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 55.759387@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 55.765322@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 55.770802@0] wifi_platform_set_power = 0
[ 55.774672@0] ======== PULL WL_REG_ON LOW! ========
[ 55.779489@0] wl_android_wifi_on: Failed
[ 55.783343@0] dhd_open : wl_android_wifi_on failed (-35)
[ 55.788673@0] dhd_stop: Enter ffffffc052ca5000
[ 55.793001@0] wl_android_wifi_off in 1
[ 55.796796@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 55.801580@0] wl_android_wifi_off out
[ 55.805373@0] dhd_stop: Exit
[ 55.809047@0] dhd_open: Exit ret=-1
[ 55.813350@0] dhd_open: Enter ffffffc052ca5000
[ 55.817574@0]
[ 55.817574@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 55.817574@0] Compiled in drivers/net/wireless/bcmdhd
[ 55.835497@0] wl_android_wifi_on in 1
[ 55.839953@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 55.843788@0] wifi_platform_set_power = 1
[ 55.847759@0] ======== PULL WL_REG_ON HIGH! ========
[ 55.852759@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 56.059713@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 56.568604@0] sdio_reset_comm():
[ 56.601152@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 56.608594@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 56.615997@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 56.625377@5] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 56.723938@7] sdio: clk 200000000 SDR mode tuning start
[ 56.728821@7] sdio: rx_tuning_result[0] = 10
[ 56.733623@7] sdio: rx_tuning_result[1] = 10
[ 56.738312@4] sdio: rx_tuning_result[2] = 10
[ 56.743005@3] sdio: rx_tuning_result[3] = 10
[ 56.746552@3] sdio: best_win_start =0, best_win_size =4
[ 56.750688@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 56.757975@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 56.764187@3] sdioh_start: set sd_f2_blocksize 128
[ 56.769273@3]
[ 56.769273@3]
[ 56.769273@3] dhd_bus_devreset: == WLAN ON ==
[ 56.781350@3] F1 signature read @0x18000000=0x15264345
[ 56.789831@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 56.794870@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 56.801590@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 56.806558@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 56.814508@3] dhd_conf_read_config: PM = 0
[ 56.818443@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 56.827198@3] dhdsdio_download_firmware: set use_rxchain 0
[ 56.832630@3] dhdsdio_download_firmware: set txglomsize 40
[ 56.838037@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 56.843582@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 56.849792@3] Final nv_path=/lib/firmware/brcm/
[ 56.854252@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 56.860272@3] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 56.869487@3] _dhdsdio_download_firmware: dongle image file download failed
[ 56.876377@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 56.881712@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 56.887719@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 56.893154@3] wifi_platform_set_power = 0
[ 56.897032@3] ======== PULL WL_REG_ON LOW! ========
[ 56.901906@3] wl_android_wifi_on: Failed
[ 56.905750@3] dhd_open : wl_android_wifi_on failed (-35)
[ 56.911075@3] dhd_stop: Enter ffffffc052ca5000
[ 56.915405@3] wl_android_wifi_off in 1
[ 56.919197@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 56.923942@3] wl_android_wifi_off out
[ 56.927592@3] dhd_stop: Exit
[ 56.931267@3] dhd_open: Exit ret=-1
[ 56.937866@3] dhd_open: Enter ffffffc052ca5000
[ 56.941551@3]
[ 56.941551@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 56.941551@3] Compiled in drivers/net/wireless/bcmdhd
[ 56.959385@3] wl_android_wifi_on in 1
[ 56.963111@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 56.967714@3] wifi_platform_set_power = 1
[ 56.971723@3] ======== PULL WL_REG_ON HIGH! ========
[ 56.976618@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 57.183562@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 57.698594@3] sdio_reset_comm():
[ 57.730762@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 57.738174@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 57.842126@5] usb 1-1.3: USB disconnect, device number 4
[ 57.844027@7] sdio: clk 200000000 SDR mode tuning start
[ 57.844293@7] sdio: rx_tuning_result[0] = 10
[ 57.844551@7] sdio: rx_tuning_result[1] = 10
[ 57.844809@7] sdio: rx_tuning_result[2] = 10
[ 57.845067@7] sdio: rx_tuning_result[3] = 10
[ 57.845095@7] sdio: best_win_start =0, best_win_size =4
[ 57.845099@7] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 57.845103@7] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 57.845157@7] sdioh_start: set sd_f2_blocksize 128
[ 57.845555@7]
[ 57.845555@7]
[ 57.845555@7] dhd_bus_devreset: == WLAN ON ==
[ 57.845739@7] F1 signature read @0x18000000=0x15264345
[ 57.849158@7] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 57.849849@7] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 57.850564@7] dhd_conf_read_nv_by_chip: nv_by_chip_count=9
[ 57.850568@7] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=0, name=nvram_ap6181.txt
[ 57.850572@7] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 57.850575@7] dhd_conf_read_nv_by_chip: chip=0xa9a6, chiprev=0, name=nvram_ap6212.txt
[ 57.850578@7] dhd_conf_read_nv_by_chip: chip=0xa9a6, chiprev=1, name=nvram_ap6212a.txt
[ 57.850581@7] dhd_conf_read_nv_by_chip: chip=0x4345, chiprev=6, name=nvram_ap6255.txt
[ 57.850584@7] dhd_conf_read_nv_by_chip: chip=0x4330, chiprev=4, name=nvram_ap6330.txt
[ 57.850588@7] dhd_conf_read_nv_by_chip: chip=0x4339, chiprev=1, name=nvram_ap6335.txt
[ 57.850591@7] dhd_conf_read_nv_by_chip: chip=0x4356, chiprev=2, name=nvram_ap6356.txt
[ 57.850594@7] dhd_conf_read_nv_by_chip: chip=0x4335, chiprev=1, name=nvram_bcm4335.txt
[ 57.850672@7] dhd_conf_read_config: mimo_bw_cap = 1
[ 57.851022@7] dhd_conf_read_config: bcn_timeout = 20
[ 57.851106@7] dhd_conf_read_config: kso_enable = 0
[ 57.851423@7] dhd_conf_read_config: PM = 0
[ 57.851765@7] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 57.851769@7] dhd_conf_set_nv_name_by_chip: nvram_path=/lib/firmware/brcm/nvram_ap6255.txt
[ 57.851772@7] dhdsdio_download_firmware: set use_rxchain 0
[ 57.851774@7] dhdsdio_download_firmware: set txglomsize 40
[ 57.851776@7] sdioh_set_mode: set txglom_mode to multi-desc
[ 57.851778@7] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 57.851779@7] Final nv_path=/lib/firmware/brcm/nvram_ap6255.txt
[ 57.851781@7] Final conf_path=/lib/firmware/brcm/config.txt
[ 57.852235@7] dhdsdio_download_code_file: Open firmware file failed /lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 57.852237@7] _dhdsdio_download_firmware: dongle image file download failed
[ 57.852266@7] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 57.852271@7] dhd_prot_ioctl : bus is down. we have nothing to do
[ 57.852273@7] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 57.852321@7] wifi_platform_set_power = 0
[ 57.852323@7] ======== PULL WL_REG_ON LOW! ========
[ 57.852325@7] wl_android_wifi_on: Failed
[ 57.852328@7] dhd_open : wl_android_wifi_on failed (-35)
[ 57.852332@7] dhd_stop: Enter ffffffc052ca5000
[ 57.852334@7] wl_android_wifi_off in 1
[ 57.852336@7] wl_android_wifi_off in 2: g_wifi_on=0
[ 57.852337@7] wl_android_wifi_off out
[ 57.852338@7] dhd_stop: Exit
[ 57.852343@7] dhd_open: Exit ret=-1
[ 57.853011@7] dhd_open: Enter ffffffc052ca5000
[ 57.853018@7]
[ 57.853018@7] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 57.853018@7] Compiled in drivers/net/wireless/bcmdhd
[ 57.853020@7] wl_android_wifi_on in 1
[ 57.853023@7] wl_android_wifi_on in 2: g_wifi_on=0
[ 57.853025@7] wifi_platform_set_power = 1
[ 57.853027@7] ======== PULL WL_REG_ON HIGH! ========
[ 57.853052@7] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 58.053089@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 58.558593@0] sdio_reset_comm():
[ 58.694256@4] sdio: clk 200000000 SDR mode tuning start
[ 58.698663@5] sdio: rx_tuning_result[0] = 10
[ 58.703099@7] sdio: rx_tuning_result[1] = 10
[ 58.709100@4] sdio: rx_tuning_result[2] = 10
[ 58.713473@4] sdio: rx_tuning_result[3] = 10
[ 58.717641@1] sdio: best_win_start =0, best_win_size =4
[ 58.721390@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 58.728687@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 58.734884@1] sdioh_start: set sd_f2_blocksize 128
[ 58.739975@1]
[ 58.739975@1]
[ 58.739975@1] dhd_bus_devreset: == WLAN ON ==
[ 58.752567@1] F1 signature read @0x18000000=0x15264345
[ 58.761011@1] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 58.766169@1] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 58.773182@1] dhd_conf_read_nv_by_chip: nv_by_chip_count=9
[ 58.777878@1] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=0, name=nvram_ap6181.txt
[ 58.785691@1] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 58.793438@1] dhd_conf_read_nv_by_chip: chip=0xa9a6, chiprev=0, name=nvram_ap6212.txt
[ 58.801235@1] dhd_conf_read_nv_by_chip: chip=0xa9a6, chiprev=1, name=nvram_ap6212a.txt
[ 58.809040@1] dhd_conf_read_nv_by_chip: chip=0x4345, chiprev=6, name=nvram_ap6255.txt
[ 58.816776@1] dhd_conf_read_nv_by_chip: chip=0x4330, chiprev=4, name=nvram_ap6330.txt
[ 58.824585@1] dhd_conf_read_nv_by_chip: chip=0x4339, chiprev=1, name=nvram_ap6335.txt
[ 58.832338@1] dhd_conf_read_nv_by_chip: chip=0x4356, chiprev=2, name=nvram_ap6356.txt
[ 58.840098@1] dhd_conf_read_nv_by_chip: chip=0x4335, chiprev=1, name=nvram_bcm4335.txt
[ 58.847980@1] dhd_conf_read_config: mimo_bw_cap = 1
[ 58.853070@1] dhd_conf_read_config: bcn_timeout = 20
[ 58.857728@1] dhd_conf_read_config: kso_enable = 0
[ 58.862700@1] dhd_conf_read_config: PM = 0
[ 58.866743@1] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 58.875289@1] dhd_conf_set_nv_name_by_chip: nvram_path=/lib/firmware/brcm/nvram_ap6255.txt
[ 58.883479@1] dhdsdio_download_firmware: set use_rxchain 0
[ 58.888904@1] dhdsdio_download_firmware: set txglomsize 40
[ 58.894312@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 58.899862@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 58.906042@1] Final nv_path=/lib/firmware/brcm/nvram_ap6255.txt
[ 58.911941@1] Final conf_path=/lib/firmware/brcm/config.txt
[ 58.972839@1] NVRAM version: AP6255_NVRAM_V1.0_29052015
[ 58.976818@1] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[ 59.060112@1] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
[ 59.064028@1] bcmsdh_oob_intr_register: Enter
[ 59.068160@1] bcmsdh_oob_intr_register: HW_OOB enabled
[ 59.073318@1] bcmsdh_oob_intr_register OOB irq=100 flags=414
[ 59.078917@1] bcmsdh_oob_intr_register: enable_irq_wake
[ 59.084041@1] bcmsdh_oob_intr_register: enable_irq_wake failed with -6
[ 59.098682@1] dhd_conf_set_fw_int_cmd: set WLC_SET_BAND 142 0
[ 59.102290@1] dhd_preinit_ioctls: Set tcpack_sup_mode 0
[ 59.109219@1] Firmware up: op_mode=0x0005, MAC=44:2c:05:f5:4a:5a
[ 59.113181@1] dhd_conf_set_country: set country CN, revision 38
[ 59.119074@1] dhd_conf_set_fw_string_struct_cmd: set country
[ 59.164010@2] Country code: CN (CN/38)
[ 59.167886@2] dhd_conf_set_fw_string_cmd: set roam_off 1
[ 59.173869@2] dhd_conf_set_fw_string_cmd: set mimo_bw_cap 1
[ 59.177996@2] dhd_conf_set_fw_string_cmd: set txbf 1
[ 59.182676@2] CONFIG-ERROR) dhd_conf_set_fw_string_cmd: txbf setting failed -23
[ 59.195320@3] Firmware version = wl0: Aug 25 2015 18:58:57 version 7.45.69 (r581703) FWID 01-24037f6e
[ 59.195325@3] Driver: 1.201.59.6 (r506368)
[ 59.195325@3] Firmware: wl0: Aug 25 2015 18:58:57 version 7.45.69 (r581703) FWID 01-24037f6e
[ 59.195547@3] dhd_txglom_enable: enable 1
[ 59.195550@3] dhd_conf_set_txglom_params: swtxglom=0, txglom_ext=0
[ 59.195551@3] dhd_conf_set_txglom_params: txglom_bucket_size=0
[ 59.195554@3] dhd_conf_set_txglom_params: txglomsize=40, deferred_tx_len=40, bus_txglom=0
[ 59.195556@3] dhd_conf_set_txglom_params: tx_in_rx=1, tx_max_offset=0
[ 59.195558@3] dhd_conf_set_disable_proptx: set disable_proptx 0
[ 59.196235@3] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64
[ 59.196723@3] wl_android_wifi_on: Success
[ 59.248956@7] dhd_open: Exit ret=0
[ 59.358639@5] usb 1-1.3: new low-speed USB device number 5 using xhci-hcd
[ 59.462579@5] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c05a
[ 59.469253@5] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 59.476615@5] usb 1-1.3: Product: USB Optical Mouse
[ 59.481749@5] usb 1-1.3: Manufacturer: Logitech
[ 59.487244@5] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 59.509046@0] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0004/input/input6
[ 59.521746@0] hid-generic 0003:046D:C05A.0004: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 59.534422@6] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 59.542638@6] platform thermal: Driver aml-thermal requests probe deferral
[ 62.107826@0] Adding 131068k swap on /var/swap. Priority:-1 extents:1 across:131068k SSFS
[ 67.223405@4] dhd_stop: Enter ffffffc052ca5000
[ 67.225236@7] wl_android_wifi_off in 1
[ 67.225240@7] wl_android_wifi_off in 2: g_wifi_on=1
[ 67.225620@7] bcmsdh_oob_intr_unregister: Enter
[ 67.225639@7] dhd_txglom_enable: enable 0
[ 67.225642@7] dhd_conf_set_txglom_params: swtxglom=0, txglom_ext=0
[ 67.225644@7] dhd_conf_set_txglom_params: txglom_bucket_size=0
[ 67.225647@7] dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0, bus_txglom=0
[ 67.225649@7] dhd_conf_set_txglom_params: tx_in_rx=1, tx_max_offset=0
[ 67.225651@7] dhd_bus_devreset: WLAN OFF DONE
[ 67.225695@7] wifi_platform_set_power = 0
[ 67.225697@7] ======== PULL WL_REG_ON LOW! ========
[ 67.225699@7] wl_android_wifi_off out
[ 67.225701@7] dhd_stop: Exit
[ 67.227083@7] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 67.348880@6] dhd_ioctl_entry: Interface is down
[ 67.348917@6] dhd_ioctl_entry: Interface is down
[ 67.349052@6] wl_iw_set_wap: WLC_DISASSOC
[ 67.349055@6] dhd_ioctl_entry: Interface is down
[ 67.349059@6] wl_iw_set_wap: WLC_DISASSOC failed (-4).
[ 67.349068@6] wl_iw_set_essid: WLC_DISASSOC
[ 67.349070@6] dhd_ioctl_entry: Interface is down
[ 67.349072@6] wl_iw_set_essid: WLC_DISASSOC failed (-4).
[ 67.885341@1] meson_uart c81004c0[ 67.891809@1] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 94.228204@0] systemd-shutdown[1]: Sending SIGTERM to remaining processes...
[ 94.265587@5] systemd-journald[2167]: Received SIGTERM from PID 1 (systemd-shutdow).
[ 94.273834@0] systemd-shutdown[1]: Sending SIGKILL to remaining processes...
[ 94.309528@0] systemd-shutdown[1]: Unmounting file systems.
[ 94.313558@0] systemd-shutdown[1]: Unmounting /tmp.
[ 94.368845@1] systemd-shutdown[1]: Unmounting /sys/kernel/config.
[ 94.428663@1] systemd-shutdown[1]: Unmounting /sys/fs/fuse/connections.
[ 94.468681@6] systemd-shutdown[1]: Unmounting /dev/mqueue.
[ 94.508604@6] systemd-shutdown[1]: Unmounting /dev/hugepages.
[ 94.548645@6] systemd-shutdown[1]: Unmounting /sys/kernel/debug.
[ 94.612395@6] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
[ 94.622820@6] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
[ 94.626662@6] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
[ 94.634548@6] systemd-shutdown[1]: All filesystems unmounted.
[ 94.638404@6] systemd-shutdown[1]: Deactivating swaps.
[ 94.643855@0] systemd-shutdown[1]: All swaps deactivated.
[ 94.648875@0] systemd-shutdown[1]: Detaching loop devices.
[ 94.656825@0] systemd-shutdown[1]: All loop devices detached.
[ 94.660207@0] systemd-shutdown[1]: Detaching DM devices.
[ 94.665914@0] systemd-shutdown[1]: All DM devices detached.
[ 94.679900@1] systemd-shutdown[1]: Rebooting.
[ 94.683052@1] avmute set to 2
[ 95.999829@1] aml_nftl_shutdown
[ 96.003012@0] reboot: Restarting system(systemd-shutdow)
[ 96.006133@0] reboot reason 1
INFO: PSCI Affinity Map:
INFO: AffInst: Level 1, MPID 0x0, State ON
INFO: AffInst: Level 1, MPID 0x100, State ON
INFO: AffInst: Level 0, MPID 0x0, State ON
INFO: AffInst: Level 0, MPID 0x1, State ON
INFO: AffInst: Level 0, MPID 0x2, State ON
INFO: AffInst: Level 0, MPID 0x3, State ON
INFO: AffInst: Level 0, MPID 0x100, State ON
INFO: AffInst: Level 0, MPID 0x101, State ON
INFO: AffInst: Level 0, MPID 0x102, State ON
INFO: AffInst: Level 0, MPID 0x103, State ON
bl31 reboot reason: 0xd
bl31 reboot reason: 0x1
system cmd 1.
GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 148679
BL2 Built : 19:58:22, Aug 31 2016.
gxl g54c8aee - xiaobo.gu@droid05
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00015400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a9a00
NOTICE: BL3-1: v1.0(debug):2e39a99
NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
aml log : bl31 normal boot !
wdt: reset registers!
[Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
OPS=0x82
fc c2 9 21 fb ca c 14 7e b4 40 63 [0.396487 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gd267f87 (Jan 19 2017 - 16:49:10)
DRAM: 2 GiB
Relocation Offset is: 76ec9000
register usb cfg[0][1] = 0000000077f5f5d8
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073ec96b0
aml_priv->desc_buf = 0x0000000073ecb9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ece270,dt_addr=0000000073ed9270
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000080000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 80000000 1
13: data d7c00000 2c5400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=normal
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 4 vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
rx version is 1.4 or below div=10
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[CANVAS]canvas init
[CANVAS]addr=0x3d851000 width=5760, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
get_cpu_id flag_12bit=1
SARADC open channel(0).
SARADC channel(0) is 0x3ca, Out of range(0x0~0x50)!
saradc - saradc sub-system
Usage:
saradc saradc open <channel> - open a SARADC channel
saradc close - close the SARADC
saradc getval - get the value in current channel
saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
get_cpu_id flag_12bit=1
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
(Re)start USB...
USB0: USB3.0 XHCI init start
Register 3000140 NbrPorts 3
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 4 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
card in
[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading s905_autoscript
871 bytes read in 5 ms (169.9 KiB/s)
## Executing script at 01020000
** Bad device usb 0 **
reading uInitrd
3930724 bytes read in 218 ms (17.2 MiB/s)
reading zImage
16367544 bytes read in 897 ms (17.4 MiB/s)
reading dtb.img
** Unable to read file dtb.img **
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
## Loading init Ramdisk from Legacy Image at 13000000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 3930660 Bytes = 3.7 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
## Flattened Device Tree blob at 01000000
Booting using the fdt blob at 0x1000000
Loading Ramdisk to 73af7000, end 73eb6a24 ... OK
Loading Device Tree to 000000001fff2000, end 000000001ffff1ca ... OK
signature:
fdt_instaboot: no instaboot image
Starting kernel ...
uboot time: 7611345 us
domain-0 init dvfs: 4
domain-1 init dvfs: 4
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-amlogics905x-gac75c6f-dirty (root@user-VirtualBox) (gcc version 4.9.4 20151028 (prerelease) (Linaro GCC 4.9-2016.02) ) #24 SMP PREEMPT Wed Feb 1 12:00:18 MSK 2017
[ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000@0] no prop version_code
[ 0.000000@0] fdt Reserved memory table:
[ 0.000000@0] linux,di: 0x000000007d300000 - 0x000000007f100000 (30 MiB)
[ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007d300000, size 30 MiB
[ 0.000000@0] linux,ion-dev: 0x0000000079300000 - 0x000000007d300000 (64 MiB)
[ 0.000000@0] linux,ppmgr: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] linux,codec_mm_cma: 0x0000000067800000 - 0x0000000073800000 (192 MiB)
[ 0.000000@0] linux,picdec: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] Reserved memory: incorrect alignment of CMA region
[ 0.000000@0] linux,codec_mm_reserved: 0x0000000075200000 - 0x0000000079300000 (65 MiB)
[ 0.000000@0] fdt Reserved memory total: 354 MiB
[ 0.000000@0] cma: Reserved 8 MiB at 74800000
[ 0.000000@0] psci: probing function IDs from device-tree
[ 0.000000@0] PERCPU: Embedded 13 pages/cpu @ffffffc075166000 s20864 r8192 d24192 u53248
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 510280
[ 0.000000@0] Kernel command line: root=LABEL=ROOTFS rootflags=data=writeback rw console=ttyS0,115200n8 console=tty0 no_console_suspend consoleblank=0 fsck.repair=yes net.ifnames=0 mac=86:37:20:48:cb:3e
[ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000@0] Memory: 1641772K/2077696K available (10134K kernel code, 895K rwdata, 3764K rodata, 1180K init, 5772K bss, 435924K reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
[ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff80423cc800 ( 35 MB)
[ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc07f100000 ( 2033 MB)
[ 0.000000@0] .init : 0xffffffc001e14000 - 0xffffffc001f3b180 ( 1181 kB)
[ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001e13a24 ( 13903 kB)
[ 0.000000@0] .data : 0xffffffc001f3c000 - 0xffffffc00201bfb8 ( 896 kB)
[ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01e12fff]
[ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000@0] arch_multi_cluster:1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] RCU debugfs-based tracing is enabled.
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[ 0.000034@0] meson_bc_timer: mclk->mux_reg =ffffff8000014990,mclk->reg =ffffff8000016994
[ 0.000361@0] Console: colour dummy device 80x25
[ 0.000882@0] console [tty0] enabled
[ 0.000904@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.000928@0] pid_max: default: 32768 minimum: 301
[ 0.001040@0] Security Framework initialized
[ 0.001072@0] AppArmor: AppArmor initialized
[ 0.001122@0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.001138@0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.003561@0] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
[ 0.003593@0] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
[ 0.003611@0] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
[ 0.003628@0] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
[ 0.006419@0] Initializing cgroup subsys debug
[ 0.006440@0] Initializing cgroup subsys freezer
[ 0.006485@0] ftrace: allocating 35111 entries in 138 pages
[ 0.050204@0] /cpus/cpu@0: Missing clock-frequency property
[ 0.050238@0] /cpus/cpu@1: Missing clock-frequency property
[ 0.050254@0] /cpus/cpu@2: Missing clock-frequency property
[ 0.050269@0] /cpus/cpu@3: Missing clock-frequency property
[ 0.050286@0] /cpus/cpu@100: Missing clock-frequency property
[ 0.050303@0] /cpus/cpu@101: Missing clock-frequency property
[ 0.050320@0] /cpus/cpu@102: Missing clock-frequency property
[ 0.050339@0] /cpus/cpu@103: Missing clock-frequency property
[ 0.050356@0] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 0.089977@0] Meson chip version = RevA (22:A - 82:0)
[ 0.110090@1] CPU1: Booted secondary processor
[ 0.130087@2] CPU2: Booted secondary processor
[ 0.150084@3] CPU3: Booted secondary processor
[ 0.170107@4] CPU4: Booted secondary processor
[ 0.190108@5] CPU5: Booted secondary processor
[ 0.210129@6] CPU6: Booted secondary processor
[ 0.230142@7] CPU7: Booted secondary processor
[ 0.230229@0] Brought up 8 CPUs
[ 0.230311@0] SMP: Total of 8 processors activated.
[ 0.230853@0] devtmpfs: initialized
[ 0.236100@2] sched: registering cpufreq notifiers for scale-invariant loads
[ 0.236231@2] instabooting: 0
[ 0.242250@2] xor: measuring software checksum speed
[ 0.339926@2] 8regs : 2291.600 MB/sec
[ 0.439955@2] 8regs_prefetch: 2158.800 MB/sec
[ 0.539983@2] 32regs : 2615.200 MB/sec
[ 0.640011@2] 32regs_prefetch: 2364.400 MB/sec
[ 0.640023@2] xor: using function: 32regs (2615.200 MB/sec)
[ 0.640043@2] pinctrl core: initialized pinctrl subsystem
[ 0.640679@2] regulator-dummy: no parameters
[ 0.641444@3] NET: Registered protocol family 16
[ 0.643147@2] cpuidle: using governor menu
[ 0.643388@2] aml_vdac_init: module init
[ 0.643546@3] register canvas platform driver
[ 0.643641@2] register rdma platform driver
[ 0.644354@2] vdso: 2 pages (1 code, 1 data) at base ffffffc001f44000
[ 0.644409@2] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.644793@2] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.645762@2] software IO TLB [mem 0x64400000-0x64800000] (4MB) mapped at [ffffffc064400000-ffffffc0647fffff]
[ 0.646235@2] aml_i2c version: 20140813
[ 0.646478@3] i2c-core: driver [pmu4] using legacy resume method
[ 0.646568@0] codec_mm:codec_mm_module_init
[ 0.646818@3] aml_watch_point_probe, in
[ 0.647249@2] gxbb_mpll_clk: register mpll_clk_out0 success done
[ 0.647270@2] gxbb_mpll_clk: register mpll_clk_out1 success done
[ 0.647285@2] gxbb_mpll_clk: register mpll_clk_out2 success done
[ 0.647491@2] clk_sys: register PLL sys_pll success done
[ 0.647511@2] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
[ 0.647523@2] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
[ 0.647536@2] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
[ 0.647548@2] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
[ 0.647561@2] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
[ 0.647573@2] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
[ 0.647585@2] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
[ 0.647597@2] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
[ 0.647608@2] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
[ 0.647644@2] gxl_clk: clock initialization complete
[ 0.647842@2] clkmsr: Gxl msr_clk_reg0=ffffff800006475c,msr_clk_reg2=ffffff8000066764
[ 0.650342@2] aml_iomap: amlogic iomap probe done
[ 0.651040@3] pinmux-gxl c1109880.pinmux: Init pinux probe!
[ 0.652178@2] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
[ 0.652657@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.652694@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ 0.652875@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.652903@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ 0.659537@3] codec_mm has 2 memory regions
[ 0.659592@3] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.659615@3] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.659734@2] codec_mm has 2 memory regions
[ 0.659760@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.659781@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.661807@2] vpu: driver version: v02
[ 0.661852@2] vpu: load vpu_clk: 666667000Hz(7)
[ 0.661940@2] vpu: vpu_probe OK
[ 0.663539@2] tv_vout: tvout_probe
[ 0.663568@2] tv_vout: major number 254 for disp
[ 0.663579@2] vout_notify: vout_register_server
[ 0.663590@2] tv_vout: register tv module server ok
[ 0.663684@2] tv_vout: tvout_probe OK
[ 0.664290@2] canvas_probe reg=00000000c8838000,size=400
[ 0.664332@2] canvas maped reg_base =ffffff8000188000
[ 0.668160@2] rdma_probe
[ 0.926883@3] bio: create slab <bio-0> at 0
[ 1.090717@0] raid6: int64x1 485 MB/s
[ 1.260708@0] raid6: int64x2 716 MB/s
[ 1.430805@0] raid6: int64x4 1035 MB/s
[ 1.600830@0] raid6: int64x8 1198 MB/s
[ 1.770976@0] raid6: neonx1 771 MB/s
[ 1.941019@0] raid6: neonx2 1201 MB/s
[ 2.111102@0] raid6: neonx4 1564 MB/s
[ 2.281196@0] raid6: neonx8 1723 MB/s
[ 2.281207@0] raid6: using algorithm neonx8 (1723 MB/s)
[ 2.281219@0] raid6: using intx1 recovery algorithm
[ 2.282025@3] SCSI subsystem initialized
[ 2.282541@2] usbcore: registered new interface driver usbfs
[ 2.282648@2] usbcore: registered new interface driver hub
[ 2.282790@3] usbcore: registered new device driver usb
[ 2.283718@2] i2c-gpio i2c_gpio.38: using pins 172 (SDA) and 173 (SCL)
[ 2.283860@3] Linux video capture interface: v2.00
[ 2.284065@2] pps_core: LinuxPPS API ver. 1 registered
[ 2.284078@2] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 2.284157@3] PTP clock support registered
[ 2.284757@3] hdmitx: system: amhdmitx_init
[ 2.284777@3] hdmitx: system: Ver: 2014May6
[ 2.284951@3] hdmitx: system: amhdmitx_probe
[ 2.285312@2] hdmitx: system: not find match init-data
[ 2.285330@2] hdmitx: system: not find match pwr-ctl
[ 2.285343@2] hdmitx hpd irq = 89
[ 2.285795@2] hdmitx20: Mapped PHY: 0xc0800000
[ 2.285818@2] hdmitx20: Mapped PHY: 0xc1104400
[ 2.285844@2] hdmitx20: Mapped PHY: 0xc8100000
[ 2.285856@2] hdmitx20: Mapped PHY: 0xc8834000
[ 2.285867@2] hdmitx20: Mapped PHY: 0xc883a000
[ 2.285879@2] hdmitx20: Mapped PHY: 0xc883c000
[ 2.285893@2] hdmitx20: Mapped PHY: 0xd0100000
[ 2.285905@2] hdmitx20: Mapped PHY: 0xda83a000
[ 2.285922@2] hdmitx: alread display in uboot 0x10
[ 2.285951@2] avmute set to 1
[ 2.286298@3] vout_serve: vout_init_module
[ 2.286440@3] vout_serve: no matched vout_init mode
[ 2.286533@3] vinfo: error: invalid vinfo. current vmode is not supported
[ 2.286548@3] vout_serve: create vout attribute OK
[ 2.286558@3] vout_serve: meson_vout_probe OK
[ 2.286737@2] logo: logo_init
[ 2.286837@2] Advanced Linux Sound Architecture Driver Initialized.
[ 2.287445@2] NetLabel: Initializing
[ 2.287464@2] NetLabel: domain hash size = 128
[ 2.287474@2] NetLabel: protocols = UNLABELED CIPSOv4
[ 2.287523@2] NetLabel: unlabeled traffic allowed by default
[ 2.288554@3] Switched to clocksource arch_sys_counter
[ 2.293009@0] hdmitx: system: irq 80000002
[ 2.301436@3] FS-Cache: Loaded
[ 2.301584@3] AppArmor: AppArmor Filesystem Enabled
[ 2.311788@3] NET: Registered protocol family 2
[ 2.312285@3] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 2.312443@3] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 2.312701@3] TCP: Hash tables configured (established 16384 bind 16384)
[ 2.312777@3] TCP: reno registered
[ 2.312794@3] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 2.312845@3] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 2.313052@3] NET: Registered protocol family 1
[ 2.313317@1] RPC: Registered named UNIX socket transport module.
[ 2.313337@1] RPC: Registered udp transport module.
[ 2.313348@1] RPC: Registered tcp transport module.
[ 2.313359@1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.313579@1] aml_wifi wifi.33: [wifi_dev_probe] no power_on_pin2
[ 2.313595@1] aml_wifi wifi.33: [wifi_dev_probe] set pwm as 32k output
[ 2.313655@1] aml_wifi wifi.33: [wifi_dev_probe] interrupt_pin=241
[ 2.313670@1] aml_wifi wifi.33: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
[ 2.313687@1] aml_wifi wifi.33: [wifi_dev_probe] power_on_pin=240
[ 2.313701@1] aml_wifi wifi.33: [wifi_dev_probe] clock_32k_pin=0
[ 2.314085@3] aml_wifi wifi.33: [wifi_setup_dt] wifi_setup_dt
[ 2.314138@3] aml_wifi wifi.33: [wifi_setup_dt] interrupt_pin(241)
[ 2.314161@3] aml_wifi wifi.33: [wifi_setup_dt] power_on_pin(240)
[ 2.314474@0] Unpacking initramfs...
[ 2.472667@2] Freeing initrd memory: 3836K (ffffffc073af7000 - ffffffc073eb6000)
[ 2.475574@1] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 2.475689@1] audit: initializing netlink subsys (disabled)
[ 2.475752@1] audit: type=2000 audit(2.440:1): initialized
[ 2.476630@0] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 2.483692@0] VFS: Disk quotas dquot_6.5.2
[ 2.483945@0] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 2.487034@0] NFS: Registering the id_resolver key type
[ 2.487088@0] Key type id_resolver registered
[ 2.487099@0] Key type id_legacy registered
[ 2.487116@0] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 2.487836@0] msgmni has been set to 3614
[ 2.489185@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 2.489216@0] io scheduler noop registered (default)
[ 2.489228@0] io scheduler deadline registered
[ 2.489412@0] io scheduler cfq registered
[ 2.491002@0] meson-rng c8834000.rng: hwrng registered
[ 2.494706@0] loop: module loaded
[ 2.495667@1] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 2.496789@0] tun: Universal TUN/TAP device driver, 1.6
[ 2.496814@0] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 2.618641@3] hdmitx: plugin
[ 2.626396@2] libphy: stmmac: probed
[ 2.626421@2] eth0: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[ 2.626435@2] eth0: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07)
[ 2.626893@2] PPP generic driver version 2.4.2
[ 2.627179@2] NET: Registered protocol family 24
[ 2.627336@1] usbcore: registered new interface driver cdc_ether
[ 2.627454@2] usbcore: registered new interface driver net1080
[ 2.627554@1] usbcore: registered new interface driver cdc_subset
[ 2.627652@2] usbcore: registered new interface driver zaurus
[ 2.627788@1] usbcore: registered new interface driver cdc_ncm
[ 2.628311@1] platform c9000000.dwc3: Driver dwc3 requests probe deferral
[ 2.628459@2] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.628475@2] ehci-h20ahb: H20AHB-EHCI Host Controller driver
[ 2.628763@1] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.629163@1] usbcore: registered new interface driver cdc_acm
[ 2.629182@1] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.629302@2] usbcore: registered new interface driver usb-storage
[ 2.629539@2] usbcore: registered new interface driver usbserial
[ 2.629640@1] usbcore: registered new interface driver usbserial_generic
[ 2.629728@2] usbserial: USB Serial support registered for generic
[ 2.629823@1] usbcore: registered new interface driver pl2303
[ 2.629910@2] usbserial: USB Serial support registered for pl2303
[ 2.630525@2] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff80001be000
[ 2.630766@1] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
[ 2.630801@1] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff80001de080
[ 2.631289@2] mousedev: PS/2 mouse device common for all mice
[ 2.631738@1] usbcore: registered new interface driver xpad
[ 2.632013@1] i2c /dev entries driver
[ 2.632386@2] usbcore: registered new interface driver uvcvideo
[ 2.632406@2] USB Video Class driver (1.1.1)
[ 2.633304@2] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: [email protected]
[ 2.633591@2] CPUidle arm64: cpuidle init start!!
[ 2.634092@1] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.634283@1] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.634553@1] usbcore: registered new interface driver usbhid
[ 2.634571@1] usbhid: USB HID core driver
[ 2.635432@1] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff80001f64c0
[ 2.635478@1] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
[ 2.635507@1] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
[ 2.754790@3] hdmitx: edid: check sum valid
[ 2.754791@3] hdmitx: edid: check sum valid
[ 2.754795@3] hdmitx: edid: blk0 raw data
[ 2.754836@3] 00ffffffffffff001e6de37689bb02000b18010380502278eaca95a6554ea126
[ 2.754836@3] 0f50542108007140818081c0a9c0b300d1c0810001019d6770a0d0a022503020
[ 2.754836@3] 3a00204f3100001a000000fd00383d1e5a1e000a202020202020000000fc004c
[ 2.754836@3] 4720554c545241574944450a000000000000000000000000000000000000017c
[ 2.754836@3]
[ 2.754836@3]
[ 2.754838@3] hdmitx: edid: blk1 raw data
[ 2.754875@3] 020317f14410040301230907078301000065030c0010009f3d70a0d0a0155030
[ 2.754875@3] 203a00204f3100001a7e4800e0a0381f4040403a00204f31000018011d007251
[ 2.754875@3] d01e206e285500204f3100001e8c0ad08a20e02d10103e9600204f3100001800
[ 2.754875@3] 0000ff003431314b4b484e35393038310a0000000000000000000000000000ce
[ 2.754875@3]
[ 2.754875@3]
[ 2.754878@3] EDID Parser:
[ 2.754929@3] hdmitx: edid: find IEEEOUT
[ 2.754932@3] hdmitx: edid: check sum valid
[ 2.754933@3] hdmitx: edid: check sum valid
[ 2.754936@3] vinfo: error: invalid vinfo. current vmode is not supported
[ 2.754938@3] hdmitx: update RX hdr info 0
[ 2.756961@3] hdmitx: ddc rd8b error 0x3a 0x00 0x00
[ 2.759004@3] [RX]-receive ksv list len:1,depth:1,cas:0,dev:0
[ 2.759009@3] vinfo: error: invalid vinfo. current vmode is not supported
[ 2.759010@3] hdmitx: video: get current mode: invalid
[ 2.759012@3] hdmitx: update rx hdr info 0
[ 2.759031@3] hdmitx: edid: not find mapped vic
[ 2.759058@3] hdmitx: system: already init VIC = 0 Now VIC = 0
[ 2.759061@3] hdmitx: system: packet: can't get vendor data
[ 2.759063@3] hdmtix: set audio
[ 2.759072@3] hdmitx tx_aud_src = 0
[ 2.759098@3] hdmitx: fs = 0, cd = 4, tmds_clk = 0
[ 2.759101@3] hdmitx aud_n_para = 6144
[ 2.759119@3] hdmitx set channel status
[ 2.759179@3] hdmtix: set audio
[ 2.759187@3] hdmitx tx_aud_src = 0
[ 2.759212@3] hdmitx: fs = 0, cd = 4, tmds_clk = 0
[ 2.759213@3] hdmitx aud_n_para = 6144
[ 2.759231@3] hdmitx set channel status
[ 4.351493@1] console [ttyS0] enabled
[ 4.355611@1] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff80001f84c0
[ 4.362211@1] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
[ 4.372217@1] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: d0078000, ctrl: 0
[ 4.380136@1] dwc_otg_driver_probe host only, not probe usb_otg!!!
[ 4.386446@1] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff]
[ 4.396175@1] meson-gpu-clkgen: probe of c883c000.gpu_clk failed with error -16
[ 4.403658@2] hdmitx: system: hdmitx_hdcp_init
[ 4.407992@1] ESM HLD: Initializing...
[ 4.411535@1] ESM HLD: Registering device range 'esm'...
[ 4.416778@1] ESM HLD: Device range 'esm' has been registered.
[ 4.422557@1] ESM HLD: Creating class /sys/class/elliptic...
[ 4.428264@1] ESM HLD: The class /sys/class/elliptic has been created.
[ 4.434633@1] ESM HLD: Creating device 'esm'...
[ 4.439329@2] ESM HLD: Device 'esm' has been created.
[ 4.444113@2] ESM HLD: Done initializing the HLD driver.
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[ 4.465422@1] aml_vrtc rtc.32: rtc core: registered aml_vrtc as rtc0
[ 4.466851@1] secmon has 1 memory regions
[ 4.470166@1] secmon: share in base: 0xffffff8000404000, share out base: 0xffffff8000406000
[ 4.478395@1] secmon secmon.4: assigned reserved memory node linux,secmon ok
[ 4.485381@1] secmon: probe done
[ 4.488925@1] storage: storage in base: 0xffffff8001600000
[ 4.494000@1] storage: storage out base: 0xffffff8001680000
[ 4.499529@1] storage: storage block base: 0xffffff8001700000
[ 4.505211@1] storage: probe done!
[ 4.509131@1] aml_sd_emmc_probe: line 3558
[ 4.512632@1] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
[ 4.522578@1] aml_sd_emmc_reg_init 1146
[ 4.525879@1] get property: ocr_avail, value:0x00200080
[ 4.532313@1] get property: f_min, value:300000
[ 4.538420@1] get property: f_max, value:100000000
[ 4.544809@1] get property: max_req_size, value:0x00020000
[ 4.551290@1] get property: pinname, str:emmc
[ 4.557051@1] get property: card_type, value:1
[ 4.562766@1] get property: gpio_dat3, str:
[ 4.568177@1] get property: hw_reset, str:
[ 4.573658@1] emmc:pdata->caps = c0000d47
[ 4.577581@1] emmc:pdata->caps2 = 18060
[ 4.581388@1] storage 1, boot 1
[ 4.584476@1] get_storage_dev return 1
[ 4.628564@2] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 4.628799@2] aml_sd_emmc_probe: line 3558
[ 4.633244@2] aml_sd_emmc_reg_init 1146
[ 4.636663@2] get property: ocr_avail, value:0x00200080
[ 4.643096@2] get property: f_min, value:400000
[ 4.649214@2] get property: f_max, value:100000000
[ 4.655590@2] get property: max_req_size, value:0x00020000
[ 4.662064@2] get property: irq_in, value:3
[ 4.667751@2] get property: irq_out, value:5
[ 4.673460@2] get property: gpio_cd, str:
[ 4.678885@2] get property: pinname, str:sd
[ 4.684485@2] get property: jtag_pin, str:
[ 4.689927@2] get property: card_type, value:5
[ 4.695611@2] get property: gpio_dat3, str:
[ 4.701069@2] sd:pdata->caps = 7
[ 4.704235@2] sd:pdata->caps2 = 0
[ 4.738759@2] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 4.738799@4] [aml_is_card_insert] card IN
[ 4.743046@2] aml_sd_emmc_probe: line 3558
[ 4.747438@2] aml_sd_emmc_reg_init 1146
[ 4.750924@2] get property: ocr_avail, value:0x00200080
[ 4.757330@2] get property: f_min, value:400000
[ 4.763461@2] get property: f_max, value:200000000
[ 4.769843@2] get property: max_req_size, value:0x00020000
[ 4.776308@2] get property: pinname, str:sdio
[ 4.782091@2] get property: card_type, value:3
[ 4.787821@2] sdio:pdata->caps = 7810f
[ 4.791491@2] sdio:pdata->caps2 = 0
[ 4.815290@0] emmc: BKOPS_EN bit is not set
[ 4.824445@0] emmc: trying cali 0-th time(s)
[ 4.827421@0] emmc: delay[0]= 4600 padding= 2, bidx=4
[ 4.828081@0] emmc: delay[1]= 4600 padding= 2, bidx=4
[ 4.833101@0] emmc: delay[2]= 4400 padding= 3, bidx=4
[ 4.833106@1] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 4.833464@2] ion_dev has 1 memory regions
[ 4.840138@4] normal card in
[ 4.850358@2] fb: osd_init_module
[ 4.850483@2] fb: viu vsync irq: 35
[ 4.850489@2] fb: failed to init reserved memory
[ 4.850505@2] tv_vout: tv_set_current_vmode[759]fps_target_mode=16
[ 4.850508@2] tv_vout: mode is 16,sync_duration_den=1,sync_duration_num=60
[ 4.850517@2] tv_vout: TV mode 1080p60hz selected.
[ 4.850521@2]
[ 4.850521@2] vdac_enable: on:0,module_sel:8
[ 4.850527@2]
[ 4.850527@2] vdac_enable: on:0,module_sel:8
[ 4.850533@2] tv_vout: new mode =1080p60hz set ok
[ 4.850534@2] vout_serve: vinfo mode is: 1080p60hz
[ 4.850771@2] osd_rdma: osd_rdma_init: rdma_table p=0x74846000,op=0x74846000 , v=0xffffff800041e000
[ 4.850773@2] osd_rdma: osd rdma request irq as second interrput function!
[ 4.850788@2] fb: osd_probe vinfo:ffffffc001fbd8a8
[ 4.850794@2] fb: init fbdev bpp is:32
[ 4.925123@2] fb: use ion buffer for fb memory
[ 4.925143@0] emmc: delay[3]= 4800 padding= 1, bidx=4
[ 4.925146@0] emmc: delay[4]= 4800 padding= 1, bidx=4
[ 4.925148@0] emmc: delay[5]= 4800 padding= 1, bidx=4
[ 4.925150@0] emmc: delay[6]= 4600 padding= 2, bidx=4
[ 4.925152@0] emmc: delay[7]= 4800 padding= 1, bidx=4
[ 4.925155@0] emmc: calibration result @ 0: max(4800), min(4400)
[ 4.925158@0] emmc: line_delay =0x1000211, max_cal_result =4800
[ 4.925160@0] emmc: base_index_max 4, base_index_min 4
[ 4.925165@0] emmc: clk 100000000 SDR mode tuning start
[ 4.925727@2] meson-fb meson-fb.16: create ion_client ffffffc0652c2540, handle=ffffffc065198740
[ 4.925732@2] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 4.925738@2] fb: Frame buffer memory assigned at
[ 4.925738@2] fb: 0, phy: 0x0000000079300000, vir:0xffffff80018c4000, size=24900K
[ 4.925738@2]
[ 4.925741@2] fb: ---------------clear fb0 memory ffffff80018c4000
[ 4.925901@0] emmc: rx_tuning_result[0] = 10
[ 4.926432@0] emmc: rx_tuning_result[1] = 10
[ 4.926963@0] emmc: rx_tuning_result[2] = 10
[ 4.927493@0] emmc: rx_tuning_result[3] = 10
[ 4.928027@0] emmc: rx_tuning_result[4] = 10
[ 4.928564@0] emmc: rx_tuning_result[5] = 10
[ 4.929099@0] emmc: rx_tuning_result[6] = 10
[ 4.929630@0] emmc: rx_tuning_result[7] = 10
[ 4.930162@0] emmc: rx_tuning_result[8] = 10
[ 4.930215@0] emmc: best_win_start =0, best_win_size =9
[ 4.930218@0] emmc: sd_emmc_regs->gclock=0x100024a,sd_emmc_regs->gadjust=0x42000
[ 4.930221@0] emmc: gclock =0x100024a, gdelay=0x1000211, gadjust=0x42000
[ 4.930556@0] emmc: new HS200 MMC card at address 0001
[ 4.931047@1] emmc: clock 100000000, 8-bit-bus-width
[ 4.931047@1]
[ 4.931047@1] mmcblk0: emmc:0001 NCard 14.4 GiB
[ 4.931190@1] mmcblk0boot0: emmc:0001 NCard partition 1 4.00 MiB
[ 4.931326@1] mmcblk0boot1: emmc:0001 NCard partition 2 4.00 MiB
[ 4.931453@1] mmcblk0rpmb: emmc:0001 NCard partition 3 4.00 MiB
[ 4.932162@0] mmcblk0: unknown partition table
[ 4.932878@1] [mmc_read_partition_tbl] mmc read partition OK!
[ 4.932879@1] add_emmc_partition
[ 4.933133@0] [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
[ 4.933313@1] [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
[ 4.933477@0] [mmcblk0p03] cache offset 0x000006c00000, size 0x000020000000
[ 4.933637@1] [mmcblk0p04] env offset 0x000027400000, size 0x000000800000
[ 4.933804@0] [mmcblk0p05] logo offset 0x000028400000, size 0x000002000000
[ 4.933971@1] [mmcblk0p06] recovery offset 0x00002ac00000, size 0x000002000000
[ 4.934139@0] [mmcblk0p07] rsv offset 0x00002d400000, size 0x000000800000
[ 4.934301@1] [mmcblk0p08] tee offset 0x00002e400000, size 0x000000800000
[ 4.934459@0] [mmcblk0p09] crypt offset 0x00002f400000, size 0x000002000000
[ 4.934616@1] [mmcblk0p10] misc offset 0x000031c00000, size 0x000002000000
[ 4.934787@0] [mmcblk0p11] instaboot offset 0x000034400000, size 0x000020000000
[ 4.934967@1] [mmcblk0p12] boot offset 0x000054c00000, size 0x000002000000
[ 4.935138@0] [mmcblk0p13] system offset 0x000057400000, size 0x000080000000
[ 4.935306@1] [mmcblk0p14] data offset 0x0000d7c00000, size 0x0002c5400000
[ 4.935340@1] card key: card_blk_probe.
[ 4.935344@1] emmc_key_init:527 emmc key lba_start:0x12020,lba_end:0x12220
[ 4.935347@1] emmc key: emmc_key_init:552 ok.
[ 4.935571@1] amlmmc_dtb_init: register dtb chardev
[ 4.935646@0] amlmmc_dtb_init: register dtb chardev OK
[ 4.935647@0] Exit aml_emmc_partition_ops OK.
[ 4.936793@1] mmcblk0boot1: unknown partition table
[ 4.936891@2] fb: osd[0] canvas.idx =0x40
[ 4.936893@2] fb: osd[0] canvas.addr=0x79300000
[ 4.936895@2] fb: osd[0] canvas.width=7680
[ 4.936896@2] fb: osd[0] canvas.height=3240
[ 4.936898@2] fb: osd[0] frame.width=1920
[ 4.936899@2] fb: osd[0] frame.height=1080
[ 4.937693@0] mmcblk0boot0: unknown partition table
[ 4.937943@1] clear_emmc_wait_flag
[ 5.014829@1] sd: new high speed SDHC card at address aaaa
[ 5.015259@0] sd: clock 50000000, 4-bit-bus-width
[ 5.015259@0]
[ 5.015259@0] mmcblk1: sd:aaaa SL08G 7.40 GiB
[ 5.016345@1] mmcblk1: p1 p2
[ 5.054676@1] Console: switching to colour frame buffer device 240x67
[ 5.528559@1] fb: osd probe OK
[ 5.533010@3] ge2d: ge2d_init_module
[ 5.537177@3] ge2d: ge2d_dev major:242
[ 5.541790@3] ge2d: ge2d clock is 400 MHZ
[ 5.545853@3] ge2d: ge2d: pdev=ffffffc06527ac00, irq=182, rstc=0xffffffc0653b6700, clk=ffffffc065244300
[ 5.553756@3] ge2d: mapped phy: 0xd0160000
[ 5.557809@3] ge2d: ge2d start monitor
[ 5.561867@0] ge2d: ge2d workqueue monitor start
[ 5.562233@1] codec:Amlogic A/V streaming port init
[ 5.564013@3] codec:get gate demux control ok ffffffc064143bc0
[ 5.564018@3] codec:get gate parser_top control ok ffffffc064143c40
[ 5.564023@3] codec:get gate vpu_intr control ok ffffffc064143cc0
[ 5.564029@3] codec:get gate vdec control ok ffffffc064143d40
[ 5.564619@3] codec:[tsync_pcr_init]init success.
[ 5.564621@3] codec:amvideocap_init_module
[ 5.564752@3] codec:amvideocap_probe,amvideocap
[ 5.564754@3] codec:use cma buf.
[ 5.564756@3] codec:amvideocap_dev_register
[ 5.566389@3] amvenc_avc_probe -- reserved memory config fail.
[ 5.566393@3] amvenc_avc - cma memory pool size: 40 MB
[ 5.566413@3] encode_wq_init.
[ 5.566418@3] encode start monitor.
[ 5.566481@1] encode workqueue monitor start.
[ 5.566970@3] jpegenc module init
[ 5.567267@3] codec:picdec_driver_probe called.
[ 5.567270@3] picdec has 1 memory regions
[ 5.567294@3] codec:picdec_driver_probe done.
[ 5.568363@3] codec:create_ge2d_work_queue video task ok
[ 5.568836@3] codec:used fix clk for vdec clk source!
[ 5.568842@3] codec:register clk_set_setting cpu[34]
[ 5.569171@3] vpu_init
[ 5.569331@3] vpu_probe
[ 5.569335@3] HevcEnc reserved memory config fail.
[ 5.569339@3] HevcEnc - cma memory pool size: 64 MB
[ 5.569341@3] HevcEnc - wave420l_irq: 219
[ 5.569381@3] vpu base address get from platform driver physical base addr=0xc8810000, virtual base=0xffffff8000588000
[ 5.569725@3] success to probe vpu device with video memory from cma
[ 5.569863@3] DI: di_module_init ok.
[ 5.569867@3] DI: di_module_init: major 235
[ 5.570063@3] DI: di_probe
[ 5.570228@3] deinterlace has 1 memory regions
[ 5.570264@3] deinterlace deinterlace.26: assigned reserved memory node linux,di ok
[ 5.570286@3] di_irq:78,timerc_irq:38
[ 5.734382@3] rdma_register, rdma_table_addr ffffff8000581000 rdma_table_addr_phy 74848000 reg_buf ffffffc0635d8000
[ 5.743996@3] rdma_register success, handle 1 table_size 8192
[ 5.749656@3] DI: di_probe allocate rdma channel 1.
[ 5.754479@3] DI: DI hw version 2.
[ 5.759209@3] 0x000000db:Y=db,U=0,V=0
[ 5.763882@3] 0x000000dc:Y=dc,U=0,V=0
[ 5.768504@3] 0x000000dd:Y=dd,U=0,V=0
[ 5.773134@3] 0x000000de:Y=de,U=0,V=0
[ 5.777703@3] 0x000000df:Y=df,U=0,V=0
[ 5.782227@3] 0x000000e0:Y=e0,U=0,V=0
[ 5.786687@3] 0x000000e1:Y=e1,U=0,V=0
[ 5.791148@3] 0x000000e2:Y=e2,U=0,V=0
[ 5.795583@3] 0x000000e3:Y=e3,U=0,V=0
[ 5.800017@3] 0x000000f0:Y=f0,U=0,V=0
[ 5.804434@3] 0x000000f1:Y=f1,U=0,V=0
[ 5.808846@3] 0x000000f2:Y=f2,U=0,V=0
[ 5.813195@3] 0x000000f3:Y=f3,U=0,V=0
[ 5.817489@3] 0x000000f4:Y=f4,U=0,V=0
[ 5.821723@3] 0x000000f5:Y=f5,U=0,V=0
[ 5.825893@3] 0x000000f6:Y=f6,U=0,V=0
[ 5.830027@3] 0x000000f7:Y=f7,U=0,V=0
[ 5.834120@3] 0x000000f8:Y=f8,U=0,V=0
[ 5.838166@3] 0x000000f9:Y=f9,U=0,V=0
[ 5.842140@3] 0x000000fa:Y=fa,U=0,V=0
[ 5.846027@3] 0x000000fb:Y=fb,U=0,V=0
[ 5.849885@3] 0x000000fc:Y=fc,U=0,V=0
[ 5.853894@3] DI: di_probe here.
[ 5.858144@3] efusekeynum: 4
[ 5.861974@3] efusekeyname: mac offset: 0 size: 6
[ 5.866469@3] efusekeyname: mac_bt offset: 6 size: 6
[ 5.872875@3] efusekeyname: mac_wifi offset: 12 size: 6
[ 5.879253@3] efusekeyname: usid offset: 18 size: 16
[ 5.886017@0] efuse efuse.10: probe OK!
[ 5.890145@3] key unify config unifykey-num is 14
[ 5.894107@3] key unify fact unifykey-num is 14
[ 5.898587@3] aml_unifykeys_probe:1273=============unifykey_devno:e900000
[ 5.905673@0] 6unifykey: device unifykeys created ok
[ 5.910480@3] 6aml_unifykeys_init done!
[ 5.914190@3] PPMGRDRV: warn: ppmgr module init func called
[ 5.919883@3] PPMGRDRV: err: ppmgr_driver_probe called
[ 5.924768@3] ppmgr has 1 memory regions
[ 5.928714@3] PPMGRDRV: info: ppmgr_dev major:232
[ 5.933767@0] PPMGRDRV: info: ppmgr_probe done
[ 5.938218@3] amlogic rfkill init
[ 5.942208@3] enter bt_probe of_node
[ 5.945977@3] not get gpio_en
[ 5.949707@3] power on valid level is high
[ 6.369124@0] ionvideo-000: V4L2 device registered as video13
[ 6.376683@0] ionvid: info: Video Technology Magazine Ion Video
[ 6.382572@0] ionvid: info: Capture Board ver 1.0 successfully loaded
[ 6.388952@0] audio_dsp: [dsp]register dsp to char divece(257)
[ 6.395737@3] amaudio: amaudio: driver amaudio succuess!
[ 6.400394@3] amlvid:err: amlvideo_init called
[ 6.404197@3] amlvid:err: amlvideo_create_instance called
[ 6.411922@3] amlvid:err: v4l2_dev.name=:amlvideo-000
[ 6.416883@0] amlvideo-000: V4L2 device registered as video10
[ 6.422843@0] [RX]-hdmirx: hdmirx_init.
[ 6.426814@0] ESM HLD: Initializing...
[ 6.430765@0] ESM HLD: Registering device range 'esm_rx'...
[ 6.435316@0] ESM HLD: Device range 'esm_rx' has been registered.
[ 6.441355@0] ESM HLD: Creating class /sys/class/elliptic_rx...
[ 6.447359@3] ESM HLD: The class /sys/class/elliptic_rx has been created.
[ 6.453966@3] ESM HLD: Creating device 'esm_rx'...
[ 6.458975@3] ESM HLD: Device 'esm_rx' has been created.
[ 6.463942@3] ESM HLD: Done initializing the HLD driver.
[ 6.469236@3] [viuin..]viuin_init_module viuin module init
[ 6.475170@3] [viuin..]viuin_probe probe ok.
[ 6.479048@3] module init
[ 6.482777@3]
[ 6.482777@3] VECM probe start
[ 6.490133@3] aml_vecm_probe: ok
[ 6.494364@3] saradc c1108680.saradc: initialized by BL30
[ 6.497993@3] saradc c1108680.saradc: calibration start:
[ 6.503068@3] saradc c1108680.saradc: nominal=0, value=5
[ 6.508274@3] saradc c1108680.saradc: nominal=256, value=250
[ 6.513902@3] saradc c1108680.saradc: nominal=512, value=499
[ 6.519519@3] saradc c1108680.saradc: nominal=768, value=750
[ 6.525093@3] saradc c1108680.saradc: nominal=1023, value=996
[ 6.530764@3] saradc c1108680.saradc: calibration end: coef=4194
[ 6.536989@3] remote: Driver init
[ 6.540926@3] remote: platform_data g_remote_ao_offset=580
[ 6.545405@3] remote: platform_data irq =228
[ 6.549696@3] remote: set drvdata completed
[ 6.555589@3] remote: device_create_file completed
[ 6.560241@3] input: aml_keypad as /devices/meson-remote.12/input/input0
[ 6.565870@3] remote: input_register_device completed
[ 6.571739@3] remote: set_remote_mode[74]
[ 6.576837@3] remote: remote config major:229
[ 6.581376@3] remote: physical address:0x636e0000
[ 6.586316@3] gpio-key gpio_keypad.48: gpio_key: 0 name(power) pin()
[ 6.591399@3] gpio-key gpio_keypad.48: amlogic_gpio_name_map_num pin 0!::
[ 6.598097@3] gpio-key gpio_keypad.48: gpio_key: 0 power(147)
[ 6.603859@3] gpio-key gpio_keypad.48: start setup_timer
[ 6.609057@3] gpio-key gpio_keypad.48: power key(116) registed.
[ 6.615189@0] input: gpio_keypad as /devices/gpio_keypad.48/input/input1
[ 6.621849@3] gpio-key gpio_keypad.48: gpio keypad register input device completed.
[ 6.629183@3] input input1: gpio keypad major:228
[ 6.634848@0] Sensor: lsm303d_init
[ 6.639846@0] Sensor: stk8313_init
[ 6.644555@3] Sensor: stk831x_init
[ 6.649257@3] Sensor: mxc622x_acc_init
[ 6.653883@0] Sensor: mxc6255xc_acc_init
[ 6.658449@3] Sensor: l3gd20_gyr_init
[ 6.664234@0] cpuinfo: probe done
[ 6.669076@3] defendkey c8834500.defendkey: defendkey_devno:e300000
[ 6.674499@0] defendkey c8834500.defendkey: defendkey: device defendkey created ok
[ 6.681979@3] defendkey: driver init
[ 6.687308@3] input: cec_input as /devices/virtual/input/input2
[ 6.692548@3] cectx aocec: aml_cec_probe(): no hdmirx reg resource
[ 6.698208@3] cectx aocec: aml_cec_probe(): no hhi reg resource
[ 6.704237@3] cectx aocec: aml_cec_probe(): can't find hdmirx
[ 6.709826@3] input input1: key 116 up
[ 6.715510@3] cec: wake up flag:0
[ 6.720622@0] aml_aes_dma c883e000.aml_aes: Aml AES_dma
[ 6.725804@3] aml_tdes_dma c883e000.aml_tdes: Aml TDES_dma
[ 6.731150@3] aml_sha_dma c883e000.aml_sha: Aml SHA1/SHA224/SHA256 dma
[ 6.738511@3] aml_codec_T9015 c8832000.t9015: aml_T9015_audio_codec_probe
[ 6.746578@0] aml_pcm_dai: pcm mode detection =1
[ 6.751728@3] aml_spdif_dai: enterd aml_spdif_play,set_clock:-1,sample_rate=4
[ 6.757872@3] aml_spdif_dai: set normal 512 fs /4 fs
[ 6.762813@3] aml_audio_hw: IEC958 16bit
[ 6.767387@3] hdmitx: audio: aout notify rate 48000
[ 6.772015@3] hdmitx: audio: aout notify size 16
[ 6.776536@3] hdmitx: audio: aout notify format CT_PCM
[ 6.781159@3] hdmtix: set audio
[ 6.785637@3] hdmitx tx_aud_src = 0
[ 6.790203@3] hdmitx: fs = 3, cd = 4, tmds_clk = 0
[ 6.794654@3] hdmitx aud_n_para = 6144
[ 6.799090@3] hdmitx set channel status
[ 6.803501@3] hdmitx: audio: Audio Type: PCM
[ 6.807848@3] hdmitx: audio: set audio param
[ 7.018765@0] aml_snd_card: headphone detection disable=1
[ 7.023196@0] aml_snd_card: no spk event delay time set
[ 7.028720@0] aml_snd_m8_card aml_m8_snd.47: T9015-audio-hifi <-> I2S.40 mapping ok
[ 7.036254@0] aml_snd_m8_card aml_m8_snd.47: dit-hifi <-> SPDIF.41 mapping ok
[ 7.042902@0] aml_pcm: enter aml_pcm_new dai->name: PCM.42 dai->id: 0
[ 7.049302@0] aml_snd_m8_card aml_m8_snd.47: pcm2bt-pcm <-> PCM.42 mapping ok
[ 7.056236@0] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTL
[ 7.063842@0] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
[ 7.072616@0] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTR
[ 7.080200@0] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[ 7.096233@0] aml_snd_card: audio use jtag pinmux as i2s output, read val =0
WARNING: Unimplemented Sip Call: 0x82000036
[ 7.107792@3] GACT probability NOT on
[ 7.112779@3] Mirror/redirect action on
[ 7.117665@3] u32 classifier
[ 7.122527@3] Actions configured
[ 7.127347@3] Netfilter messages via NETLINK v0.30.
[ 7.132339@3] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 7.138409@0] ctnetlink v0.93: registering with nfnetlink.
[ 7.144118@0] xt_time: kernel timezone is -0000
[ 7.149310@0] ipip: IPv4 over IPv4 tunneling driver
[ 7.155165@0] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.160357@0] arp_tables: (C) 2002 David S. Miller
[ 7.165389@0] TCP: cubic registered
[ 7.170339@0] Initializing XFRM netlink socket
[ 7.176210@3] NET: Registered protocol family 10
[ 7.182418@0] mip6: Mobile IPv6
[ 7.187416@0] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.192732@0] sit: IPv6 over IPv4 tunneling driver
[ 7.199283@0] NET: Registered protocol family 17
[ 7.204421@0] NET: Registered protocol family 15
[ 7.209554@0] Bridge firewalling registered
[ 7.214488@0] l2tp_core: L2TP core driver, V2.0
[ 7.219308@0] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 7.224236@0] l2tp_netlink: L2TP netlink interface
[ 7.229178@0] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 7.235020@0] l2tp_debugfs: L2TP debugfs support
[ 7.240008@0] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 7.246197@0] NET: Registered protocol family 35
[ 7.251412@0] Key type dns_resolver registered
[ 7.257259@0] Registering SWP/SWPB emulation handler
[ 7.264880@0] bio: create slab <bio-1> at 1
[ 7.271227@0] Btrfs loaded
[ 7.276395@0] BTRFS: selftest: Running btrfs free space cache tests
[ 7.282117@0] BTRFS: selftest: Running extent only tests
[ 7.287361@0] BTRFS: selftest: Running bitmap only tests
[ 7.292651@0] BTRFS: selftest: Running bitmap and extent tests
[ 7.298402@0] BTRFS: selftest: Free space cache tests finished
[ 7.304175@0] BTRFS: selftest: Running extent buffer operation tests
[ 7.310297@0] BTRFS: selftest: Running btrfs_split_item tests
[ 7.320320@0] BTRFS: selftest: Running find delalloc tests
[ 7.538442@0] BTRFS: selftest: Running btrfs_get_extent tests
[ 7.544085@0] BTRFS: selftest: Running hole first btrfs_get_extent test
[ 7.638637@0] AppArmor: AppArmor sha1 policy hashing enabled
[ 7.643611@0] regulator-dummy: disabling
[ 8.351018@2] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 8.355962@2] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 8.364090@2] xhci-hcd xhci-hcd.0.auto: irq 62, io mem 0xc9000000
[ 8.369870@2] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.376633@2] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.383973@2] usb usb1: Product: xHCI Host Controller
[ 8.389034@2] usb usb1: Manufacturer: Linux 3.14.29 xhci-hcd
[ 8.394572@2] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 8.400390@2] hub 1-0:1.0: USB hub found
[ 8.405533@2] hub 1-0:1.0: 3 ports detected
[ 8.410958@2] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 8.416112@2] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 8.423984@2] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 8.430765@2] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.438085@2] usb usb2: Product: xHCI Host Controller
[ 8.443300@2] usb usb2: Manufacturer: Linux 3.14.29 xhci-hcd
[ 8.448702@2] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 8.454497@2] hub 2-0:1.0: USB hub found
[ 8.459702@2] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 8.467223@7] console [netcon0] enabled
[ 8.473501@7] netconsole: network logging started
[ 8.479740@7] aml_vrtc rtc.32: setting system clock to 2015-01-01 00:00:16 UTC (1420070416)
[ 8.490170@7] gxbb_pm: enter meson_pm_probe!
[ 8.496517@7] gxbb_pm: meson_pm_probe done
[ 8.503218@2] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 8.510898@2] platform thermal: Driver aml-thermal requests probe deferral
[ 8.517767@2] aml_istbt_dev_ready NULL
[ 8.523157@2] ALSA device list:
[ 8.528455@2] #0: AML-M8AUDIO
[ 8.534374@2] Freeing unused kernel memory: 1180K (ffffffc001e14000 - ffffffc001f3b000)
[ 8.574921@2] systemd-udevd[2066]: starting version 215
[ 8.581650@2] random: systemd-udevd urandom read with 43 bits of entropy available
[ 8.728637@6] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 8.878644@7] usb 1-1: New USB device found, idVendor=05ac, idProduct=1006
[ 8.886587@7] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8.894955@7] usb 1-1: Product: Keyboard Hub
[ 8.901620@7] usb 1-1: Manufacturer: Apple, Inc.
[ 8.908254@7] usb 1-1: SerialNumber: 000000000000
[ 8.936095@0] hub 1-1:1.0: USB hub found
[ 8.941703@0] hub 1-1:1.0: 3 ports detected
[ 8.948580@3] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 8.956538@3] platform thermal: Driver aml-thermal requests probe deferral
[ 9.218631@5] usb 1-1.2: new low-speed USB device number 3 using xhci-hcd
[ 9.344735@5] usb 1-1.2: New USB device found, idVendor=05ac, idProduct=0220
[ 9.344741@5] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 9.344745@5] usb 1-1.2: Product: Apple Keyboard
[ 9.344749@5] usb 1-1.2: Manufacturer: Apple, Inc
[ 9.345532@7] usb 1-1.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 9.345548@7] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 9.355845@3] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 9.355856@3] platform thermal: Driver aml-thermal requests probe deferral
[ 9.358090@5] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 9.358102@5] platform thermal: Driver aml-thermal requests probe deferral
[ 9.362407@5] input: Apple, Inc Apple Keyboard as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.2/1-1.2:1.0/0003:05AC:0220.0001/input/input3
[ 9.362714@5] apple 0003:05AC:0220.0001: input,hidraw0: USB HID v1.11 Keyboard [Apple, Inc Apple Keyboard] on usb-xhci-hcd.0.auto-1.2/input0
[ 9.362956@4] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 9.362967@4] platform thermal: Driver aml-thermal requests probe deferral
[ 9.363710@5] input: Apple, Inc Apple Keyboard as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.2/1-1.2:1.1/0003:05AC:0220.0002/input/input4
[ 9.364021@5] apple 0003:05AC:0220.0002: input,hidraw1: USB HID v1.11 Device [Apple, Inc Apple Keyboard] on usb-xhci-hcd.0.auto-1.2/input1
[ 9.364256@4] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 9.364266@4] platform thermal: Driver aml-thermal requests probe deferral
[ 9.443132@4] usb 1-1.3: new low-speed USB device number 4 using xhci-hcd
[ 9.582577@4] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c05a
[ 9.592748@4] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 9.603284@4] usb 1-1.3: Product: USB Optical Mouse
[ 9.611951@4] usb 1-1.3: Manufacturer: Logitech
[ 9.621400@1] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 9.642816@0] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0003/input/input5
[ 9.643182@0] hid-generic 0003:046D:C05A.0003: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 9.643487@5] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 9.643500@5] platform thermal: Driver aml-thermal requests probe deferral
[ 9.717950@0] random: nonblocking pool is initialized
[ 9.746357@2] EXT4-fs (mmcblk1p2): mounted filesystem with writeback data mode. Opts: data=writeback
[ 10.090471@6] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[ 10.108529@6] systemd[1]: Detected architecture 'arm64'.
[ 10.159437@2] systemd[1]: Inserted module 'autofs4'
[ 10.168822@2] systemd[1]: Set hostname to <amlogic-s905x>.
[ 10.220882@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 10.456876@2] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[ 10.476388@2] systemd[1]: Expecting device dev-ttyS0.device...
[ 10.494265@2] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 10.505176@2] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 10.515788@2] systemd[1]: Starting Remote File Systems (Pre).
[ 10.533206@2] systemd[1]: Reached target Remote File Systems (Pre).
[ 10.542486@2] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 10.563870@2] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 10.576706@2] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 10.588319@2] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 10.599697@2] systemd[1]: Starting Paths.
[ 10.617593@2] systemd[1]: Reached target Paths.
[ 10.626407@2] systemd[1]: Starting Encrypted Volumes.
[ 10.644183@2] systemd[1]: Reached target Encrypted Volumes.
[ 10.652919@2] systemd[1]: Expecting device dev-disk-by\x2dlabel-BOOT.device...
[ 10.672192@2] systemd[1]: Starting Root Slice.
[ 10.689977@2] systemd[1]: Created slice Root Slice.
[ 10.698720@2] systemd[1]: Starting Delayed Shutdown Socket.
[ 10.716658@2] systemd[1]: Listening on Delayed Shutdown Socket.
[ 10.725666@2] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 10.744704@2] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 10.754913@2] systemd[1]: Starting Journal Socket (/dev/log).
[ 10.772570@2] systemd[1]: Listening on Journal Socket (/dev/log).
[ 10.781411@2] systemd[1]: Starting User and Session Slice.
[ 10.798407@2] systemd[1]: Created slice User and Session Slice.
[ 10.806802@2] systemd[1]: Starting udev Control Socket.
[ 10.823135@2] systemd[1]: Listening on udev Control Socket.
[ 10.831092@2] systemd[1]: Starting udev Kernel Socket.
[ 10.847158@2] systemd[1]: Listening on udev Kernel Socket.
[ 10.855057@2] systemd[1]: Starting Journal Socket.
[ 10.871160@2] systemd[1]: Listening on Journal Socket.
[ 10.879121@2] systemd[1]: Starting System Slice.
[ 10.894939@2] systemd[1]: Created slice System Slice.
[ 10.902498@2] systemd[1]: Starting system-systemd\x2dfsck.slice.
[ 10.918055@2] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 10.926196@2] systemd[1]: Starting Increase datagram queue length...
[ 10.943290@2] systemd[1]: Starting Restore / save the current clock...
[ 10.966894@2] systemd[1]: Mounting Huge Pages File System...
[ 10.983355@2] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 11.004109@2] systemd[1]: Mounting Debug File System...
[ 11.020312@2] systemd[1]: Starting udev Coldplug all Devices...
[ 11.037128@2] systemd[1]: Mounting POSIX Message Queue File System...
[ 11.058807@2] systemd[1]: Started Set Up Additional Binary Formats.
[ 11.066830@2] systemd[1]: Starting LSB: Set keymap...
[ 11.084665@2] systemd[1]: Starting system-serial\x2dgetty.slice.
[ 11.099836@2] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 11.107625@2] systemd[1]: Starting system-getty.slice.
[ 11.122224@2] systemd[1]: Created slice system-getty.slice.
[ 11.131700@2] systemd[1]: Starting Load Kernel Modules...
[ 11.147300@2] systemd[1]: Started File System Check on Root Device.
[ 11.154873@2] systemd[1]: Starting Slices.
[ 11.165769@3] fuse init (API version 7.22)
[ 11.169638@3] Triggered SDIO WiFi power on and bus rescan.
[ 11.169659@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 11.189741@2] systemd[1]: Reached target Slices.
[ 11.204660@2] systemd[1]: Mounted POSIX Message Queue File System.
[ 11.219066@2] systemd[1]: Mounted Debug File System.
[ 11.232796@2] systemd[1]: Mounted Huge Pages File System.
[ 11.247405@2] systemd[1]: Started Increase datagram queue length.
[ 11.262987@2] systemd[1]: Started Restore / save the current clock.
[ 11.278829@2] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 11.299711@2] systemd[1]: Started LSB: Set keymap.
[ 11.307946@2] systemd[1]: Time has been changed
[ 11.341532@2] systemd[1]: Started udev Coldplug all Devices.
[ 11.368981@2] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 11.385768@2] systemd[1]: Starting Syslog Socket.
[ 11.400213@2] systemd[1]: Listening on Syslog Socket.
[ 11.407125@2] systemd[1]: Starting Journal Service...
[ 11.430092@2] systemd[1]: Started Journal Service.
[ 11.478626@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 11.493123@2] systemd-udevd[2170]: starting version 215
[ 11.822141@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 11.833029@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 11.846194@3] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 11.858635@1] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 11.959116@5] sdio: clk 200000000 SDR mode tuning start
[ 11.966753@5] sdio: rx_tuning_result[0] = 10
[ 11.974287@5] sdio: rx_tuning_result[1] = 10
[ 11.981859@0] sdio: rx_tuning_result[2] = 10
[ 11.988031@0] sdio: rx_tuning_result[3] = 10
[ 11.993853@0] sdio: best_win_start =0, best_win_size =4
[ 11.999602@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 12.007132@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 12.018265@0] sdio: queuing unknown CIS tuple 0x91 (3 bytes)
[ 12.024098@0] sdio: new ultra high speed SDR104 SDIO card at address 0001
[ 12.031018@0] sdio: clock 200000000, 4-bit-bus-width
[ 12.037108@4] [sdio_reinit] finish
[ 12.257461@0] ionvid: info: ionvideo open
[ 12.363358@7] aml_nftl_dev: module license 'Proprietary' taints kernel.
[ 12.371347@7] Disabling lock debugging due to kernel taint
[ 12.380376@0] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 12.388531@0] platform thermal: Driver aml-thermal requests probe deferral
[ 12.458008@7] aml_audio_i2s_mute_flag: flag=0
[ 12.458620@5] ionvid: info: ionvideo_stop_generating!!!!
[ 12.458637@5] ionvid: info: ionvideo release
[ 12.470381@6] cfg80211: Calling CRDA to update world regulatory domain
[ 12.486726@7] aml_audio_set_spdif_mute: flag=0
[ 12.486743@7] aml_snd_card: aml_m8_set_spk: aml_m8_spk_enabled=0
[ 12.570865@7] dhd_module_init: in
[ 12.577648@7] ======== bcm_wlan_set_plat_data ========
[ 12.584422@7] host_oob_irq: 100
[ 12.591011@7] host_oob_irq_flags=0x414
[ 12.597483@1] dhd_wifi_platform_load: Enter
[ 12.602926@1] Power-up adapter 'DHD generic adapter'
[ 12.608304@1] wifi_platform_set_power = 1
[ 12.608307@1] ======== PULL WL_REG_ON HIGH! ========
[ 12.608329@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 12.808368@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 13.318560@1] wifi_platform_bus_enumerate device present 1
[ 13.323999@1] ======== Card detection to detect SDIO card! ========
[ 13.330085@1] sdio_reset_comm():
[ 13.363768@1] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 13.371928@1] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 13.379996@1] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 13.390090@1] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 13.489333@7] sdio: clk 200000000 SDR mode tuning start
[ 13.495912@7] sdio: rx_tuning_result[0] = 10
[ 13.502414@7] sdio: rx_tuning_result[1] = 10
[ 13.508952@0] sdio: rx_tuning_result[2] = 10
[ 13.514279@0] sdio: rx_tuning_result[3] = 10
[ 13.519310@0] sdio: best_win_start =0, best_win_size =4
[ 13.524325@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 13.531225@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 13.537334@0] [sdio_reinit] finish
[ 13.542833@4] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 13.551407@4] platform thermal: Driver aml-thermal requests probe deferral
[ 13.558778@0] bcmsdh_register: register client driver
[ 13.558875@0] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[ 13.558950@0] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[ 13.558953@0] bus num (host idx)=0, slot num (rca)=1
[ 13.558955@0] found adapter info 'DHD generic adapter'
[ 13.559025@0] sdioh_attach: set sd_f2_blocksize 128
[ 13.559393@0] dhdsdio_probe : no mutex held. set lock
[ 13.559518@0] F1 signature read @0x18000000=0x15264345
[ 13.563160@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 13.563898@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 13.563988@0] dhd_conf_set_chiprev: chip=0x4345, chiprev=6
[ 13.564031@0] dhd_conf_set_conf_path_by_nv_path: config_path=/lib/firmware/brcm/config.txt
[ 13.641378@4] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 13.650457@2] platform thermal: Driver aml-thermal requests probe deferral
[ 14.506673@4] EXT4-fs (mmcblk1p2): re-mounted. Opts: commit=600,errors=remount-ro
[ 14.539657@5] dhd_conf_read_nv_by_chip: nv_by_chip_count=9
[ 14.539663@5] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=0, name=nvram_ap6181.txt
[ 14.539666@5] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 14.539669@5] dhd_conf_read_nv_by_chip: chip=0xa9a6, chiprev=0, name=nvram_ap6212.txt
[ 14.539672@5] dhd_conf_read_nv_by_chip: chip=0xa9a6, chiprev=1, name=nvram_ap6212a.txt
[ 14.539676@5] dhd_conf_read_nv_by_chip: chip=0x4345, chiprev=6, name=nvram_ap6255.txt
[ 14.539679@5] dhd_conf_read_nv_by_chip: chip=0x4330, chiprev=4, name=nvram_ap6330.txt
[ 14.539682@5] dhd_conf_read_nv_by_chip: chip=0x4339, chiprev=1, name=nvram_ap6335.txt
[ 14.539685@5] dhd_conf_read_nv_by_chip: chip=0x4356, chiprev=2, name=nvram_ap6356.txt
[ 14.539688@5] dhd_conf_read_nv_by_chip: chip=0x4335, chiprev=1, name=nvram_bcm4335.txt
[ 14.539767@5] dhd_conf_read_config: mimo_bw_cap = 1
[ 14.540119@5] dhd_conf_read_config: bcn_timeout = 20
[ 14.540203@5] dhd_conf_read_config: kso_enable = 0
[ 14.540522@5] dhd_conf_read_config: PM = 0
[ 14.541366@6] wl_create_event_handler(): thread:wl_event_handler:8ea started
[ 14.541388@1] tsk Enter, tsk = 0xffffff80015da940
[ 14.541595@6] dhd_attach(): thread:dhd_watchdog_thread:8eb started
[ 14.541638@7] dhd_attach(): thread:dhd_dpc:8ec started
[ 14.541678@2] dhd_dpc_thread: set dpc_cpucore 0 from config.txt
[ 14.541681@7] dhd_attach(): thread:dhd_rxf:8ed started
[ 14.541693@7] dhd_deferred_work_init: work queue initialized
[ 14.552319@7] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 14.552319@7] Compiled in drivers/net/wireless/bcmdhd
[ 14.552916@7] Register interface [wlan0] MAC: 44:2c:05:f5:4a:5a
[ 14.552916@7]
[ 14.552922@7] dhd_prot_ioctl : bus is down. we have nothing to do
[ 14.552978@7] bcmsdh_oob_intr_unregister: Enter
[ 14.552980@7] bcmsdh_oob_intr_unregister: irq is not registered
[ 14.552989@7] dhd_txglom_enable: enable 0
[ 14.552992@7] dhd_conf_set_txglom_params: swtxglom=0, txglom_ext=0
[ 14.552993@7] dhd_conf_set_txglom_params: txglom_bucket_size=0
[ 14.552996@7] dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0, bus_txglom=0
[ 14.552998@7] dhd_conf_set_txglom_params: tx_in_rx=1, tx_max_offset=0
[ 14.553000@7] dhd_bus_devreset: WLAN OFF DONE
[ 14.553047@7] wifi_platform_set_power = 0
[ 14.553049@7] ======== PULL WL_REG_ON LOW! ========
[ 14.553052@7] dhdsdio_probe : the lock is released.
[ 14.553133@7] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[ 14.553186@7] dhd_module_init: Exit err=0
[ 14.553363@5] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 14.553376@5] platform thermal: Driver aml-thermal requests probe deferral
[ 14.596805@6] BT_RADIO going: on
[ 14.596807@6] BCM_BT: going ON
[ 14.607592@5] Bluetooth: Core ver 2.18
[ 14.607641@5] NET: Registered protocol family 31
[ 14.607643@5] Bluetooth: HCI device and connection manager initialized
[ 14.607675@5] Bluetooth: HCI socket layer initialized
[ 14.607682@5] Bluetooth: L2CAP socket layer initialized
[ 14.607711@5] Bluetooth: SCO socket layer initialized
[ 14.616066@5] Bluetooth: Generic Bluetooth SDIO driver ver 0.1
[ 14.625808@4] cfg80211: World regulatory domain updated:
[ 14.625814@4] cfg80211: DFS Master region: unset
[ 14.625814@4] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 14.625820@4] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 14.625822@4] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 14.625825@4] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 14.625828@4] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 14.625831@4] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 14.625833@4] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[ 14.625836@4] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 14.625839@4] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 14.957664@0] Adding 131068k swap on /var/swap. Priority:-1 extents:1 across:131068k SSFS
[ 15.171783@5] systemd-journald[2168]: Received request to flush runtime journal from PID 1
[ 15.585362@1] aml_audio_i2s_mute_flag: flag=0
[ 15.585375@1] aml_audio_set_spdif_mute: flag=0
[ 15.585386@1] aml_snd_card: aml_m8_set_spk: aml_m8_spk_enabled=0
[ 15.696588@3] vout_serve: vmode set to 720p60hz
[ 15.696588@3]
[ 15.696611@3] fb: current vmode=1080p60hz
[ 15.696620@3] tv_vout: tv_set_current_vmode[759]fps_target_mode=10
[ 15.696623@3] tv_vout: mode is 10,sync_duration_den=1,sync_duration_num=60
[ 15.696631@3] tv_vout: TV mode 720p60hz selected.
[ 15.696635@3]
[ 15.696635@3] vdac_enable: on:0,module_sel:8
[ 15.696640@3]
[ 15.696640@3] vdac_enable: on:0,module_sel:8
[ 15.696646@3] tv_vout: new mode =720p60hz set ok
[ 15.696647@3] vout_serve: vinfo mode is: 720p60hz
[ 15.696649@3] vout_serve: new mode 720p60hz
[ 15.696649@3] set ok
[ 15.696667@3] hdmitx: video: get current mode: 720p60hz
[ 15.696668@3] hdmitx: update rx hdr info 0
[ 15.696684@3] hdmitx: get ext_name
[ 15.696716@3] hdmitx: system: already init VIC = 0 Now VIC = 4
[ 15.696719@3] hdmitx: rx no SCDC present indicator
[ 15.698737@3] hdmitx: ddc rd8b error 0x54 0x01
[ 15.700760@3] hdmitx: ddc rd8b error 0x54 0x01
[ 15.700767@3] hdmirx version is 1.4 or below
[ 15.700769@3] hdmitx div40: 0
[ 15.728598@3] hdmitx: system: set mode VIC 4 (cd0,cs0,pm1,vd0,1)
[ 15.728600@3] hdmitx: system: set pll
[ 15.728601@3] hdmitx: system: param->VIC:4
[ 15.728604@3] hdmitx: set clk: VIC = 4 cd = 4
[ 15.728609@3] config HPLL = 2970000
[ 15.728629@3] HPLL: 0xc000027b
[ 15.728630@3] config HPLL done
[ 15.728636@3] set_hpll_od3_clk_div[441] div = 6
[ 15.728643@3] j = 2 vid_clk_div = 1
[ 15.728654@3] hdmitx: set enc for VIC: 4
[ 15.728673@3] hdmitx_set_hw[4867] set VIC = 4
[ 15.738699@0] hdmitx: system: irq 80000001
[ 15.738828@0] Start = 0x10000100 End = 0x100001ff
[ 15.738838@0] [0x10000104]: 0x00000001
[ 15.738841@0] [0x10000105]: 0x00000003
[ 15.739010@0] [0x10000170]: 0x00000004
[ 15.739035@0] [0x10000180]: 0x000000ff
[ 15.739038@0] [0x10000181]: 0x000000ff
[ 15.739041@0] [0x10000182]: 0x00000003
[ 15.739044@0] [0x10000183]: 0x00000007
[ 15.739047@0] [0x10000184]: 0x0000003f
[ 15.739050@0] [0x10000185]: 0x00000002
[ 15.739054@0] [0x10000187]: 0x000000ff
[ 15.739057@0] [0x10000188]: 0x00000003
[ 15.740589@3] hdmitx: ddc w1b error 0x54 0x20 0x00
[ 15.740703@0] hdmitx: system: irq 80000001
[ 15.740717@0] Start = 0x10000100 End = 0x100001ff
[ 15.740727@0] [0x10000104]: 0x00000001
[ 15.740730@0] [0x10000105]: 0x00000003
[ 15.740893@0] [0x10000170]: 0x00000004
[ 15.740919@0] [0x10000180]: 0x000000ff
[ 15.740922@0] [0x10000181]: 0x000000ff
[ 15.740925@0] [0x10000182]: 0x00000003
[ 15.740928@0] [0x10000183]: 0x00000007
[ 15.740930@0] [0x10000184]: 0x0000003f
[ 15.740933@0] [0x10000185]: 0x00000002
[ 15.740938@0] [0x10000187]: 0x000000ff
[ 15.740941@0] [0x10000188]: 0x00000003
[ 15.742606@3] hdmitx: ddc w1b error 0x54 0x20 0x00
[ 15.742723@0] hdmitx: system: irq 80000001
[ 15.742747@0] Start = 0x10000100 End = 0x100001ff
[ 15.742756@0] [0x10000104]: 0x00000001
[ 15.742759@0] [0x10000105]: 0x00000003
[ 15.742920@0] [0x10000170]: 0x00000004
[ 15.742945@0] [0x10000180]: 0x000000ff
[ 15.742948@0] [0x10000181]: 0x000000ff
[ 15.742951@0] [0x10000182]: 0x00000003
[ 15.742954@0] [0x10000183]: 0x00000007
[ 15.742957@0] [0x10000184]: 0x0000003f
[ 15.742959@0] [0x10000185]: 0x00000002
[ 15.742964@0] [0x10000187]: 0x000000ff
[ 15.742967@0] [0x10000188]: 0x00000003
[ 15.744617@3] hdmitx: ddc rd8b error 0x54 0x21
[ 15.860643@3] hdmitx: system: phy setting done
[ 15.864660@3] Sink is HDMI device
[ 15.864669@3] hdmitx: system: packet: can't get vendor data
[ 15.864673@3] hdmtix: set audio
[ 15.864682@3] hdmitx tx_aud_src = 0
[ 15.864710@3] hdmitx: fs = 3, cd = 4, tmds_clk = 74250
[ 15.864712@3] hdmitx aud_n_para = 6144
[ 15.864731@3] hdmitx set channel status
[ 15.864793@3] hdmitx: audio: Audio Type: PCM
[ 15.864799@3] fb: current vmode=720p60hz
[ 16.119031@6] fb: osd[0] canvas.idx =0x40
[ 16.119034@6] fb: osd[0] canvas.addr=0x79300000
[ 16.119037@6] fb: osd[0] canvas.width=3840
[ 16.119039@6] fb: osd[0] canvas.height=1440
[ 16.119075@2] fb: osd[0] frame.width=1280
[ 16.119077@2] fb: osd[0] frame.height=720
[ 16.177163@2] fb: use ion buffer for fb memory
[ 16.177220@2] meson-fb meson-fb.16: create ion_client ffffffc0652c2540, handle=ffffffc064147b40
[ 16.177225@2] meson-fb meson-fb.16: ion memory(1): created fb at 0x000000007ab51000, size 1 MiB
[ 16.177231@2] fb: Frame buffer memory assigned at
[ 16.177231@2] fb: 1, phy: 0x000000007ab51000, vir:0xffffff8003bd4000, size=1024K
[ 16.177231@2]
[ 16.177233@2] fb: fb1 open, logo index:1
[ 16.214745@1] fb: osd[1] canvas.idx =0x43
[ 16.214748@1] fb: osd[1] canvas.addr=0x7ab51000
[ 16.214751@1] fb: osd[1] canvas.width=128
[ 16.214752@1] fb: osd[1] canvas.height=32
[ 16.214753@1] fb: osd[1] frame.width=32
[ 16.214755@1] fb: osd[1] frame.height=32
[ 16.250045@4] vout_serve: vmode set to 720p60hz
[ 16.250045@4]
[ 16.250048@4] vout_serve: don't set the same mode as current
[ 16.250142@4] fb: osd0 free scale DISABLE
[ 16.267674@4] fb: osd[0] enable: 1 (amlogics905x_in)
[ 16.944448@1] dhd_open: Enter ffffffc052c9b000
[ 16.948186@1]
[ 16.948186@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 16.948186@1] Compiled in drivers/net/wireless/bcmdhd
[ 16.965698@1] wl_android_wifi_on in 1
[ 16.969318@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 16.974001@1] wifi_platform_set_power = 1
[ 16.977966@1] ======== PULL WL_REG_ON HIGH! ========
[ 16.982944@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 17.131680@3] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 17.189856@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 17.698571@1] sdio_reset_comm():
[ 17.730760@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 17.738341@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 17.745864@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 17.755404@4] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 17.853801@7] sdio: clk 200000000 SDR mode tuning start
[ 17.858779@7] sdio: rx_tuning_result[0] = 10
[ 17.863658@4] sdio: rx_tuning_result[1] = 10
[ 17.868395@4] sdio: rx_tuning_result[2] = 10
[ 17.873156@3] sdio: rx_tuning_result[3] = 10
[ 17.876736@3] sdio: best_win_start =0, best_win_size =4
[ 17.880826@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 17.888121@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 17.894336@3] sdioh_start: set sd_f2_blocksize 128
[ 17.899424@3]
[ 17.899424@3]
[ 17.899424@3] dhd_bus_devreset: == WLAN ON ==
[ 17.912475@3] F1 signature read @0x18000000=0x15264345
[ 17.921035@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 17.926462@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 17.933424@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=9
[ 17.938144@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=0, name=nvram_ap6181.txt
[ 17.945941@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 17.953694@3] dhd_conf_read_nv_by_chip: chip=0xa9a6, chiprev=0, name=nvram_ap6212.txt
[ 17.961462@3] dhd_conf_read_nv_by_chip: chip=0xa9a6, chiprev=1, name=nvram_ap6212a.txt
[ 17.969316@3] dhd_conf_read_nv_by_chip: chip=0x4345, chiprev=6, name=nvram_ap6255.txt
[ 17.977041@3] dhd_conf_read_nv_by_chip: chip=0x4330, chiprev=4, name=nvram_ap6330.txt
[ 17.984829@3] dhd_conf_read_nv_by_chip: chip=0x4339, chiprev=1, name=nvram_ap6335.txt
[ 17.992599@3] dhd_conf_read_nv_by_chip: chip=0x4356, chiprev=2, name=nvram_ap6356.txt
[ 18.000359@3] dhd_conf_read_nv_by_chip: chip=0x4335, chiprev=1, name=nvram_bcm4335.txt
[ 18.008242@3] dhd_conf_read_config: mimo_bw_cap = 1
[ 18.013323@3] dhd_conf_read_config: bcn_timeout = 20
[ 18.017991@3] dhd_conf_read_config: kso_enable = 0
[ 18.022957@3] dhd_conf_read_config: PM = 0
[ 18.027007@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 18.035545@3] dhd_conf_set_nv_name_by_chip: nvram_path=/lib/firmware/brcm/nvram_ap6255.txt
[ 18.043742@3] dhdsdio_download_firmware: set use_rxchain 0
[ 18.049175@3] dhdsdio_download_firmware: set txglomsize 40
[ 18.054580@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 18.060127@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 18.066309@3] Final nv_path=/lib/firmware/brcm/nvram_ap6255.txt
[ 18.072198@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 18.134059@3] NVRAM version: AP6255_NVRAM_V1.0_29052015
[ 18.137965@3] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[ 18.221077@2] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
[ 18.224727@2] bcmsdh_oob_intr_register: Enter
[ 18.228917@2] bcmsdh_oob_intr_register: HW_OOB enabled
[ 18.233980@2] bcmsdh_oob_intr_register OOB irq=100 flags=414
[ 18.239623@2] bcmsdh_oob_intr_register: enable_irq_wake
[ 18.244763@2] bcmsdh_oob_intr_register: enable_irq_wake failed with -6
[ 18.252127@2] dhd_conf_set_fw_int_cmd: set WLC_SET_BAND 142 0
[ 18.257121@2] dhd_preinit_ioctls: Set tcpack_sup_mode 0
[ 18.264053@2] Firmware up: op_mode=0x0005, MAC=44:2c:05:f5:4a:5a
[ 18.268049@2] dhd_conf_set_country: set country CN, revision 38
[ 18.273933@2] dhd_conf_set_fw_string_struct_cmd: set country
[ 18.318899@2] Country code: CN (CN/38)
[ 18.322711@2] dhd_conf_set_fw_string_cmd: set roam_off 1
[ 18.328413@2] dhd_conf_set_fw_string_cmd: set mimo_bw_cap 1
[ 18.332440@2] dhd_conf_set_fw_string_cmd: set txbf 1
[ 18.337049@2] CONFIG-ERROR) dhd_conf_set_fw_string_cmd: txbf setting failed -23
[ 18.349735@2] Firmware version = wl0: Aug 25 2015 18:58:57 version 7.45.69 (r581703) FWID 01-24037f6e
[ 18.356880@2] Driver: 1.201.59.6 (r506368)
[ 18.356880@2] Firmware: wl0: Aug 25 2015 18:58:57 version 7.45.69 (r581703) FWID 01-24037f6e
[ 18.371671@2] dhd_txglom_enable: enable 1
[ 18.375353@2] dhd_conf_set_txglom_params: swtxglom=0, txglom_ext=0
[ 18.381496@2] dhd_conf_set_txglom_params: txglom_bucket_size=0
[ 18.387255@2] dhd_conf_set_txglom_params: txglomsize=40, deferred_tx_len=40, bus_txglom=0
[ 18.395382@2] dhd_conf_set_txglom_params: tx_in_rx=1, tx_max_offset=0
[ 18.401759@2] dhd_conf_set_disable_proptx: set disable_proptx 0
[ 18.408347@2] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64
[ 18.415243@2] wl_android_wifi_on: Success
[ 18.471718@2] dhd_open: Exit ret=0
[ 18.628828@5] meson_uart c81004c0[400000 change 115200 to 115200
[ 18.645025@7] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 18.645233@7] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
Debian GNU/Linux 8 amlogic-s905x ttyS0
amlogic-s905x login: [ 57.832103@4] usb 1-1.3: USB disconnect, device number 4
[ 59.088624@4] usb 1-1.3: new low-speed USB device number 5 using xhci-hcd
[ 59.192704@5] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c05a
[ 59.199588@5] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 59.206962@5] usb 1-1.3: Product: USB Optical Mouse
[ 59.212815@5] usb 1-1.3: Manufacturer: Logitech
[ 59.219016@5] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 59.242743@0] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0004/input/input6
[ 59.255645@0] hid-generic 0003:046D:C05A.0004: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 59.268794@4] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 59.277416@4] platform thermal: Driver aml-thermal requests probe deferral
[ 98.916944@3] fb: osd[0] canvas.idx =0x40
[ 98.916947@3] fb: osd[0] canvas.addr=0x79300000
[ 98.916949@3] fb: osd[0] canvas.width=7680
[ 98.916950@3] fb: osd[0] canvas.height=3240
[ 98.916952@3] fb: osd[0] frame.width=1920
[ 98.916954@3] fb: osd[0] frame.height=1080
[ 98.973668@0] fb: osd[0] canvas.idx =0x40
[ 98.973671@0] fb: osd[0] canvas.addr=0x79300000
[ 98.973673@0] fb: osd[0] canvas.width=3840
[ 98.973674@0] fb: osd[0] canvas.height=1440
[ 98.973676@0] fb: osd[0] frame.width=1280
[ 98.973677@0] fb: osd[0] frame.height=720
[ 107.240091@6] usb 1-1.3: USB disconnect, device number 5
[ 108.758616@7] usb 1-1.3: new low-speed USB device number 6 using xhci-hcd
[ 108.862629@7] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c05a
[ 108.864232@7] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 108.871680@7] usb 1-1.3: Product: USB Optical Mouse
[ 108.876483@7] usb 1-1.3: Manufacturer: Logitech
[ 108.881351@7] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 108.907014@7] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0005/input/input7
[ 108.915414@7] hid-generic 0003:046D:C05A.0005: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 108.928061@4] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 108.935682@4] platform thermal: Driver aml-thermal requests probe deferral
[ 123.498844@4] libphy: stmmac-0:00 - Link is Up - 100/Full
[ 156.904089@4] usb 1-1.3: USB disconnect, device number 6
[ 158.418610@5] usb 1-1.3: new low-speed USB device number 7 using xhci-hcd
[ 158.522542@5] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c05a
[ 158.528294@5] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 158.535739@5] usb 1-1.3: Product: USB Optical Mouse
[ 158.540867@5] usb 1-1.3: Manufacturer: Logitech
[ 158.545546@5] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 158.570768@0] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0006/input/input8
[ 158.582845@0] hid-generic 0003:046D:C05A.0006: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 158.595584@5] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 158.603164@5] platform thermal: Driver aml-thermal requests probe deferral
[ 167.498812@4] libphy: stmmac-0:00 - Link is Down
[ 176.498816@4] libphy: stmmac-0:00 - Link is Up - 100/Full
[ 206.568090@7] usb 1-1.3: USB disconnect, device number 7
[ 208.078608@4] usb 1-1.3: new low-speed USB device number 8 using xhci-hcd
[ 208.182580@4] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c05a
[ 208.188404@4] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 208.195848@4] usb 1-1.3: Product: USB Optical Mouse
[ 208.200683@4] usb 1-1.3: Manufacturer: Logitech
[ 208.205480@4] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 208.234758@0] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0007/input/input9
[ 208.246920@0] hid-generic 0003:046D:C05A.0007: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 208.259614@4] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 208.267152@4] platform thermal: Driver aml-thermal requests probe deferral
[ 256.232092@5] usb 1-1.3: USB disconnect, device number 8
[ 256.522498@7] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 257.748611@6] usb 1-1.3: new low-speed USB device number 9 using xhci-hcd
[ 257.852540@6] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c05a
[ 257.858763@6] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 257.866157@6] usb 1-1.3: Product: USB Optical Mouse
[ 257.871011@6] usb 1-1.3: Manufacturer: Logitech
[ 257.876884@6] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 257.898798@0] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0008/input/input10
[ 257.911177@0] hid-generic 0003:046D:C05A.0008: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 257.923988@6] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 257.931787@6] platform thermal: Driver aml-thermal requests probe deferral
[ 259.508825@7] libphy: stmmac-0:00 - Link is Up - 100/Full
[ 259.515212@7] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 305.896131@5] usb 1-1.3: USB disconnect, device number 9
[ 307.408627@5] usb 1-1.3: new low-speed USB device number 10 using xhci-hcd
[ 307.512629@5] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c05a
[ 307.516958@5] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 307.524403@5] usb 1-1.3: Product: USB Optical Mouse
[ 307.529239@5] usb 1-1.3: Manufacturer: Logitech
[ 307.534033@5] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 307.562958@0] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0009/input/input11
[ 307.573956@0] hid-generic 0003:046D:C05A.0009: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 307.586729@6] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 307.594243@6] platform thermal: Driver aml-thermal requests probe deferral
Debian GNU/Linux 8 amlogic-s905x ttyS0
amlogic-s905x login: [ 355.816103@6] usb 1-1.3: USB disconnect, device number 10
[ 357.078613@6] usb 1-1.3: new low-speed USB device number 11 using xhci-hcd
[ 357.182539@6] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c05a
[ 357.188445@6] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 357.195889@6] usb 1-1.3: Product: USB Optical Mouse
[ 357.201294@6] usb 1-1.3: Manufacturer: Logitech
[ 357.206942@6] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 357.226777@0] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.000A/input/input12
[ 357.239161@0] hid-generic 0003:046D:C05A.000A: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 357.251891@7] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 357.259733@7] platform thermal: Driver aml-thermal requests probe deferral
[ 405.480108@7] usb 1-1.3: USB disconnect, device number 11
[ 406.738617@7] usb 1-1.3: new low-speed USB device number 12 using xhci-hcd
[ 406.842544@7] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c05a
[ 406.849930@7] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 406.857752@7] usb 1-1.3: Product: USB Optical Mouse
[ 406.863798@7] usb 1-1.3: Manufacturer: Logitech
[ 406.870232@0] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 406.890744@0] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.000B/input/input13
[ 406.904362@0] hid-generic 0003:046D:C05A.000B: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 406.917753@5] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 406.927176@5] platform thermal: Driver aml-thermal requests probe deferral
[ 455.144105@5] usb 1-1.3: USB disconnect, device number 12
[ 456.398615@5] usb 1-1.3: new low-speed USB device number 13 using xhci-hcd
[ 456.522541@5] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c05a
[ 456.531596@5] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 456.541138@5] usb 1-1.3: Product: USB Optical Mouse
[ 456.550031@5] usb 1-1.3: Manufacturer: Logitech
[ 456.559327@1] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 456.586750@0] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.000C/input/input14
[ 456.601602@0] hid-generic 0003:046D:C05A.000C: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 456.616049@5] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 456.626657@5] platform thermal: Driver aml-thermal requests probe deferral
[ 504.808102@6] usb 1-1.3: USB disconnect, device number 13
[ 506.318655@7] usb 1-1.3: new low-speed USB device number 14 using xhci-hcd
[ 506.432705@7] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c05a
[ 506.442443@7] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 506.452643@7] usb 1-1.3: Product: USB Optical Mouse
[ 506.460912@7] usb 1-1.3: Manufacturer: Logitech
[ 506.469318@0] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 506.506904@0] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.000D/input/input15
[ 506.521831@0] hid-generic 0003:046D:C05A.000D: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 506.536367@4] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 506.546993@4] platform thermal: Driver aml-thermal requests probe deferral
[ 543.647863@5] dhd_stop: Enter ffffffc052c9b000
[ 543.647910@5] dhd_set_mcast_list_handler: interface info not available/down
[ 543.665736@7] wl_android_wifi_off in 1
[ 543.665740@7] wl_android_wifi_off in 2: g_wifi_on=1
[ 543.666135@7] bcmsdh_oob_intr_unregister: Enter
[ 543.666155@7] dhd_txglom_enable: enable 0
[ 543.666158@7] dhd_conf_set_txglom_params: swtxglom=0, txglom_ext=0
[ 543.666160@7] dhd_conf_set_txglom_params: txglom_bucket_size=0
[ 543.666163@7] dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0, bus_txglom=0
[ 543.666165@7] dhd_conf_set_txglom_params: tx_in_rx=1, tx_max_offset=0
[ 543.666166@7] dhd_bus_devreset: WLAN OFF DONE
[ 543.666212@7] wifi_platform_set_power = 0
[ 543.666214@7] ======== PULL WL_REG_ON LOW! ========
[ 543.666215@7] wl_android_wifi_off out
[ 543.666218@7] dhd_stop: Exit
[ 543.667564@7] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 543.858807@0] meson_uart c81004c0.[ 543.865609@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 544.820144@0] systemd-shutdown[1]: Sending SIGTERM to remaining processes...
[ 544.856959@4] systemd-journald[2168]: Received SIGTERM from PID 1 (systemd-shutdow).
[ 544.865084@0] systemd-shutdown[1]: Sending SIGKILL to remaining processes...
[ 544.901003@0] systemd-shutdown[1]: Unmounting file systems.
[ 544.904956@0] systemd-shutdown[1]: Unmounting /sys/kernel/config.
[ 544.988682@0] systemd-shutdown[1]: Unmounting /sys/fs/fuse/connections.
[ 545.048723@4] systemd-shutdown[1]: Unmounting /dev/mqueue.
[ 545.088633@4] systemd-shutdown[1]: Unmounting /sys/kernel/debug.
[ 545.128601@4] systemd-shutdown[1]: Unmounting /dev/hugepages.
[ 545.316789@5] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
[ 545.329969@5] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
[ 545.333784@5] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
[ 545.339246@5] systemd-shutdown[1]: All filesystems unmounted.
[ 545.344893@5] systemd-shutdown[1]: Deactivating swaps.
[ 545.350316@5] systemd-shutdown[1]: All swaps deactivated.
[ 545.355328@5] systemd-shutdown[1]: Detaching loop devices.
[ 545.363782@2] systemd-shutdown[1]: All loop devices detached.
[ 545.367102@2] systemd-shutdown[1]: Detaching DM devices.
[ 545.372858@2] systemd-shutdown[1]: All DM devices detached.
[ 545.386794@3] systemd-shutdown[1]: Rebooting.
[ 545.389985@3] avmute set to 2
[ 546.699848@3] aml_nftl_shutdown
[ 546.702978@0] reboot: Restarting system(systemd-shutdow)
[ 546.706042@0] reboot reason 1
INFO: PSCI Affinity Map:
INFO: AffInst: Level 1, MPID 0x0, State ON
INFO: AffInst: Level 1, MPID 0x100, State ON
INFO: AffInst: Level 0, MPID 0x0, State ON
INFO: AffInst: Level 0, MPID 0x1, State ON
INFO: AffInst: Level 0, MPID 0x2, State ON
INFO: AffInst: Level 0, MPID 0x3, State ON
INFO: AffInst: Level 0, MPID 0x100, State ON
INFO: AffInst: Level 0, MPID 0x101, State ON
INFO: AffInst: Level 0, MPID 0x102, State ON
INFO: AffInst: Level 0, MPID 0x103, State ON
bl31 reboot reason: 0xd
bl31 reboot reason: 0x1
system cmd 1.
GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 148942
BL2 Built : 19:58:22, Aug 31 2016.
gxl g54c8aee - xiaobo.gu@droid05
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00015400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a9a00
NOTICE: BL3-1: v1.0(debug):2e39a99
NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
aml log : bl31 normal boot !
wdt: reset registers!
[Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
OPS=0x82
fc c2 9 21 fb ca c 14 7e b4 40 63 [0.396749 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gd267f87 (Jan 19 2017 - 16:49:10)
DRAM: 2 GiB
Relocation Offset is: 76ec9000
register usb cfg[0][1] = 0000000077f5f5d8
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073ec96b0
aml_priv->desc_buf = 0x0000000073ecb9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ece270,dt_addr=0000000073ed9270
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000080000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 80000000 1
13: data d7c00000 2c5400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=normal
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 4 vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
rx version is 1.4 or below div=10
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[CANVAS]canvas init
[CANVAS]addr=0x3d851000 width=5760, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
get_cpu_id flag_12bit=1
SARADC open channel(0).
SARADC channel(0) is 0x3c8, Out of range(0x0~0x50)!
saradc - saradc sub-system
Usage:
saradc saradc open <channel> - open a SARADC channel
saradc close - close the SARADC
saradc getval - get the value in current channel
saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
get_cpu_id flag_12bit=1
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
(Re)start USB...
USB0: USB3.0 XHCI init start
Register 3000140 NbrPorts 3
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 4 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
card in
[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading s905_autoscript
871 bytes read in 5 ms (169.9 KiB/s)
## Executing script at 01020000
** Bad device usb 0 **
reading uInitrd
3939414 bytes read in 218 ms (17.2 MiB/s)
reading zImage
16367544 bytes read in 897 ms (17.4 MiB/s)
reading dtb.img
** Unable to read file dtb.img **
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
## Loading init Ramdisk from Legacy Image at 13000000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 3939350 Bytes = 3.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
## Flattened Device Tree blob at 01000000
Booting using the fdt blob at 0x1000000
Loading Ramdisk to 73af4000, end 73eb5c16 ... OK
Loading Device Tree to 000000001fff2000, end 000000001ffff1ca ... OK
signature:
fdt_instaboot: no instaboot image
Starting kernel ...
uboot time: 7611533 us
domain-0 init dvfs: 4
domain-1 init dvfs: 4
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-amlogics905x-gac75c6f-dirty (root@user-VirtualBox) (gcc version 4.9.4 20151028 (prerelease) (Linaro GCC 4.9-2016.02) ) #24 SMP PREEMPT Wed Feb 1 12:00:18 MSK 2017
[ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000@0] no prop version_code
[ 0.000000@0] fdt Reserved memory table:
[ 0.000000@0] linux,di: 0x000000007d300000 - 0x000000007f100000 (30 MiB)
[ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007d300000, size 30 MiB
[ 0.000000@0] linux,ion-dev: 0x0000000079300000 - 0x000000007d300000 (64 MiB)
[ 0.000000@0] linux,ppmgr: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] linux,codec_mm_cma: 0x0000000067800000 - 0x0000000073800000 (192 MiB)
[ 0.000000@0] linux,picdec: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] Reserved memory: incorrect alignment of CMA region
[ 0.000000@0] linux,codec_mm_reserved: 0x0000000075200000 - 0x0000000079300000 (65 MiB)
[ 0.000000@0] fdt Reserved memory total: 354 MiB
[ 0.000000@0] cma: Reserved 8 MiB at 74800000
[ 0.000000@0] psci: probing function IDs from device-tree
[ 0.000000@0] PERCPU: Embedded 13 pages/cpu @ffffffc075166000 s20864 r8192 d24192 u53248
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 510280
[ 0.000000@0] Kernel command line: root=LABEL=ROOTFS rootflags=data=writeback rw console=ttyS0,115200n8 console=tty0 no_console_suspend consoleblank=0 fsck.repair=yes net.ifnames=0 mac=86:37:20:48:cb:3e
[ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000@0] Memory: 1641764K/2077696K available (10134K kernel code, 895K rwdata, 3764K rodata, 1180K init, 5772K bss, 435932K reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
[ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff80423cc800 ( 35 MB)
[ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc07f100000 ( 2033 MB)
[ 0.000000@0] .init : 0xffffffc001e14000 - 0xffffffc001f3b180 ( 1181 kB)
[ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001e13a24 ( 13903 kB)
[ 0.000000@0] .data : 0xffffffc001f3c000 - 0xffffffc00201bfb8 ( 896 kB)
[ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01e12fff]
[ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000@0] arch_multi_cluster:1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] RCU debugfs-based tracing is enabled.
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[ 0.000033@0] meson_bc_timer: mclk->mux_reg =ffffff8000014990,mclk->reg =ffffff8000016994
[ 0.000364@0] Console: colour dummy device 80x25
[ 0.000885@0] console [tty0] enabled
[ 0.000907@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.000931@0] pid_max: default: 32768 minimum: 301
[ 0.001044@0] Security Framework initialized
[ 0.001075@0] AppArmor: AppArmor initialized
[ 0.001125@0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.001141@0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.003573@0] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
[ 0.003605@0] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
[ 0.003623@0] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
[ 0.003640@0] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
[ 0.006462@0] Initializing cgroup subsys debug
[ 0.006483@0] Initializing cgroup subsys freezer
[ 0.006528@0] ftrace: allocating 35111 entries in 138 pages
[ 0.050223@0] /cpus/cpu@0: Missing clock-frequency property
[ 0.050256@0] /cpus/cpu@1: Missing clock-frequency property
[ 0.050272@0] /cpus/cpu@2: Missing clock-frequency property
[ 0.050287@0] /cpus/cpu@3: Missing clock-frequency property
[ 0.050303@0] /cpus/cpu@100: Missing clock-frequency property
[ 0.050320@0] /cpus/cpu@101: Missing clock-frequency property
[ 0.050338@0] /cpus/cpu@102: Missing clock-frequency property
[ 0.050356@0] /cpus/cpu@103: Missing clock-frequency property
[ 0.050374@0] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 0.089993@0] Meson chip version = RevA (22:A - 82:0)
[ 0.110104@1] CPU1: Booted secondary processor
[ 0.130105@2] CPU2: Booted secondary processor
[ 0.150105@3] CPU3: Booted secondary processor
[ 0.170128@4] CPU4: Booted secondary processor
[ 0.190129@5] CPU5: Booted secondary processor
[ 0.210144@6] CPU6: Booted secondary processor
[ 0.230160@7] CPU7: Booted secondary processor
[ 0.230245@0] Brought up 8 CPUs
[ 0.230327@0] SMP: Total of 8 processors activated.
[ 0.230870@0] devtmpfs: initialized
[ 0.236124@2] sched: registering cpufreq notifiers for scale-invariant loads
[ 0.236257@2] instabooting: 0
[ 0.242246@2] xor: measuring software checksum speed
[ 0.339943@2] 8regs : 2291.600 MB/sec
[ 0.439971@2] 8regs_prefetch: 2158.800 MB/sec
[ 0.539999@2] 32regs : 2615.200 MB/sec
[ 0.640027@2] 32regs_prefetch: 2364.400 MB/sec
[ 0.640039@2] xor: using function: 32regs (2615.200 MB/sec)
[ 0.640058@2] pinctrl core: initialized pinctrl subsystem
[ 0.640686@2] regulator-dummy: no parameters
[ 0.641412@2] NET: Registered protocol family 16
[ 0.643131@2] cpuidle: using governor menu
[ 0.643372@2] aml_vdac_init: module init
[ 0.643534@2] register canvas platform driver
[ 0.643628@2] register rdma platform driver
[ 0.644351@2] vdso: 2 pages (1 code, 1 data) at base ffffffc001f44000
[ 0.644406@2] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.644785@2] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.645753@2] software IO TLB [mem 0x64400000-0x64800000] (4MB) mapped at [ffffffc064400000-ffffffc0647fffff]
[ 0.646249@2] aml_i2c version: 20140813
[ 0.646482@0] i2c-core: driver [pmu4] using legacy resume method
[ 0.646577@2] codec_mm:codec_mm_module_init
[ 0.646815@2] aml_watch_point_probe, in
[ 0.647256@2] gxbb_mpll_clk: register mpll_clk_out0 success done
[ 0.647275@2] gxbb_mpll_clk: register mpll_clk_out1 success done
[ 0.647290@2] gxbb_mpll_clk: register mpll_clk_out2 success done
[ 0.647492@2] clk_sys: register PLL sys_pll success done
[ 0.647512@2] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
[ 0.647525@2] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
[ 0.647538@2] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
[ 0.647550@2] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
[ 0.647562@2] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
[ 0.647574@2] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
[ 0.647586@2] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
[ 0.647598@2] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
[ 0.647610@2] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
[ 0.647647@2] gxl_clk: clock initialization complete
[ 0.647839@2] clkmsr: Gxl msr_clk_reg0=ffffff800006475c,msr_clk_reg2=ffffff8000066764
[ 0.650344@3] aml_iomap: amlogic iomap probe done
[ 0.651034@2] pinmux-gxl c1109880.pinmux: Init pinux probe!
[ 0.652145@2] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
[ 0.652630@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.652667@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ 0.652845@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.652874@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ 0.659503@2] codec_mm has 2 memory regions
[ 0.659560@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.659583@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.659700@3] codec_mm has 2 memory regions
[ 0.659725@3] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.659747@3] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.661780@2] vpu: driver version: v02
[ 0.661823@2] vpu: load vpu_clk: 666667000Hz(7)
[ 0.661908@2] vpu: vpu_probe OK
[ 0.663481@2] tv_vout: tvout_probe
[ 0.663514@2] tv_vout: major number 254 for disp
[ 0.663526@2] vout_notify: vout_register_server
[ 0.663536@2] tv_vout: register tv module server ok
[ 0.663625@2] tv_vout: tvout_probe OK
[ 0.664225@2] canvas_probe reg=00000000c8838000,size=400
[ 0.664263@2] canvas maped reg_base =ffffff8000188000
[ 0.668098@2] rdma_probe
[ 0.926403@2] bio: create slab <bio-0> at 0
[ 1.090709@0] raid6: int64x1 484 MB/s
[ 1.260741@0] raid6: int64x2 716 MB/s
[ 1.430809@0] raid6: int64x4 1035 MB/s
[ 1.600842@0] raid6: int64x8 1197 MB/s
[ 1.770942@0] raid6: neonx1 771 MB/s
[ 1.941027@0] raid6: neonx2 1201 MB/s
[ 2.111126@0] raid6: neonx4 1564 MB/s
[ 2.281202@0] raid6: neonx8 1724 MB/s
[ 2.281213@0] raid6: using algorithm neonx8 (1724 MB/s)
[ 2.281224@0] raid6: using intx1 recovery algorithm
[ 2.282037@2] SCSI subsystem initialized
[ 2.282560@3] usbcore: registered new interface driver usbfs
[ 2.282674@2] usbcore: registered new interface driver hub
[ 2.282815@2] usbcore: registered new device driver usb
[ 2.283742@2] i2c-gpio i2c_gpio.38: using pins 172 (SDA) and 173 (SCL)
[ 2.283881@2] Linux video capture interface: v2.00
[ 2.284091@2] pps_core: LinuxPPS API ver. 1 registered
[ 2.284107@2] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 2.284181@2] PTP clock support registered
[ 2.284772@2] hdmitx: system: amhdmitx_init
[ 2.284793@2] hdmitx: system: Ver: 2014May6
[ 2.284966@2] hdmitx: system: amhdmitx_probe
[ 2.285313@3] hdmitx: system: not find match init-data
[ 2.285331@3] hdmitx: system: not find match pwr-ctl
[ 2.285344@3] hdmitx hpd irq = 89
[ 2.285817@2] hdmitx20: Mapped PHY: 0xc0800000
[ 2.285839@2] hdmitx20: Mapped PHY: 0xc1104400
[ 2.285865@2] hdmitx20: Mapped PHY: 0xc8100000
[ 2.285878@2] hdmitx20: Mapped PHY: 0xc8834000
[ 2.285890@2] hdmitx20: Mapped PHY: 0xc883a000
[ 2.285901@2] hdmitx20: Mapped PHY: 0xc883c000
[ 2.285916@2] hdmitx20: Mapped PHY: 0xd0100000
[ 2.285928@2] hdmitx20: Mapped PHY: 0xda83a000
[ 2.285944@2] hdmitx: alread display in uboot 0x10
[ 2.285973@2] avmute set to 1
[ 2.286307@3] vout_serve: vout_init_module
[ 2.286443@3] vout_serve: no matched vout_init mode
[ 2.286542@2] vinfo: error: invalid vinfo. current vmode is not supported
[ 2.286557@2] vout_serve: create vout attribute OK
[ 2.286568@2] vout_serve: meson_vout_probe OK
[ 2.286749@2] logo: logo_init
[ 2.286846@2] Advanced Linux Sound Architecture Driver Initialized.
[ 2.287456@2] NetLabel: Initializing
[ 2.287473@2] NetLabel: domain hash size = 128
[ 2.287483@2] NetLabel: protocols = UNLABELED CIPSOv4
[ 2.287531@2] NetLabel: unlabeled traffic allowed by default
[ 2.288567@2] Switched to clocksource arch_sys_counter
[ 2.293031@0] hdmitx: system: irq 80000002
[ 2.301467@2] FS-Cache: Loaded
[ 2.301616@2] AppArmor: AppArmor Filesystem Enabled
[ 2.311911@3] NET: Registered protocol family 2
[ 2.312416@3] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 2.312574@3] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 2.312831@3] TCP: Hash tables configured (established 16384 bind 16384)
[ 2.312906@3] TCP: reno registered
[ 2.312923@3] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 2.312975@3] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 2.313185@3] NET: Registered protocol family 1
[ 2.313462@1] RPC: Registered named UNIX socket transport module.
[ 2.313481@1] RPC: Registered udp transport module.
[ 2.313492@1] RPC: Registered tcp transport module.
[ 2.313502@1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.313726@1] aml_wifi wifi.33: [wifi_dev_probe] no power_on_pin2
[ 2.313743@1] aml_wifi wifi.33: [wifi_dev_probe] set pwm as 32k output
[ 2.313803@1] aml_wifi wifi.33: [wifi_dev_probe] interrupt_pin=241
[ 2.313818@1] aml_wifi wifi.33: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
[ 2.313835@1] aml_wifi wifi.33: [wifi_dev_probe] power_on_pin=240
[ 2.313849@1] aml_wifi wifi.33: [wifi_dev_probe] clock_32k_pin=0
[ 2.314231@3] aml_wifi wifi.33: [wifi_setup_dt] wifi_setup_dt
[ 2.314281@3] aml_wifi wifi.33: [wifi_setup_dt] interrupt_pin(241)
[ 2.314304@3] aml_wifi wifi.33: [wifi_setup_dt] power_on_pin(240)
[ 2.314615@0] Unpacking initramfs...
[ 2.472888@0] Freeing initrd memory: 3844K (ffffffc073af4000 - ffffffc073eb5000)
[ 2.475767@0] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 2.475882@0] audit: initializing netlink subsys (disabled)
[ 2.475945@0] audit: type=2000 audit(2.440:1): initialized
[ 2.476816@3] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 2.483791@0] VFS: Disk quotas dquot_6.5.2
[ 2.484043@3] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 2.487063@0] NFS: Registering the id_resolver key type
[ 2.487112@0] Key type id_resolver registered
[ 2.487123@0] Key type id_legacy registered
[ 2.487140@0] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 2.487843@0] msgmni has been set to 3614
[ 2.489170@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 2.489201@0] io scheduler noop registered (default)
[ 2.489213@0] io scheduler deadline registered
[ 2.489401@3] io scheduler cfq registered
[ 2.490990@0] meson-rng c8834000.rng: hwrng registered
[ 2.494712@0] loop: module loaded
[ 2.495734@0] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 2.496842@0] tun: Universal TUN/TAP device driver, 1.6
[ 2.496866@0] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 2.618665@2] hdmitx: plugin
[ 2.626529@0] libphy: stmmac: probed
[ 2.626553@0] eth0: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[ 2.626568@0] eth0: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07)
[ 2.627026@0] PPP generic driver version 2.4.2
[ 2.627305@0] NET: Registered protocol family 24
[ 2.627471@3] usbcore: registered new interface driver cdc_ether
[ 2.627580@0] usbcore: registered new interface driver net1080
[ 2.627694@3] usbcore: registered new interface driver cdc_subset
[ 2.627799@0] usbcore: registered new interface driver zaurus
[ 2.627929@3] usbcore: registered new interface driver cdc_ncm
[ 2.628455@3] platform c9000000.dwc3: Driver dwc3 requests probe deferral
[ 2.628645@3] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.628663@3] ehci-h20ahb: H20AHB-EHCI Host Controller driver
[ 2.628923@0] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.629314@0] usbcore: registered new interface driver cdc_acm
[ 2.629332@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.629452@3] usbcore: registered new interface driver usb-storage
[ 2.629694@3] usbcore: registered new interface driver usbserial
[ 2.629804@0] usbcore: registered new interface driver usbserial_generic
[ 2.629894@3] usbserial: USB Serial support registered for generic
[ 2.629992@0] usbcore: registered new interface driver pl2303
[ 2.630075@3] usbserial: USB Serial support registered for pl2303
[ 2.630700@3] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff80001be000
[ 2.630935@0] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
[ 2.630971@0] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff80001de080
[ 2.631465@3] mousedev: PS/2 mouse device common for all mice
[ 2.631921@0] usbcore: registered new interface driver xpad
[ 2.632181@0] i2c /dev entries driver
[ 2.632549@3] usbcore: registered new interface driver uvcvideo
[ 2.632567@3] USB Video Class driver (1.1.1)
[ 2.633462@3] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: [email protected]
[ 2.633747@3] CPUidle arm64: cpuidle init start!!
[ 2.634252@0] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.634436@0] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.634710@0] usbcore: registered new interface driver usbhid
[ 2.634727@0] usbhid: USB HID core driver
[ 2.635580@0] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff80001f64c0
[ 2.635626@0] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
[ 2.635655@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
[ 2.754803@2] hdmitx: edid: check sum valid
[ 2.754804@2] hdmitx: edid: check sum valid
[ 2.754808@2] hdmitx: edid: blk0 raw data
[ 2.754849@2] 00ffffffffffff001e6de37689bb02000b18010380502278eaca95a6554ea126
[ 2.754849@2] 0f50542108007140818081c0a9c0b300d1c0810001019d6770a0d0a022503020
[ 2.754849@2] 3a00204f3100001a000000fd00383d1e5a1e000a202020202020000000fc004c
[ 2.754849@2] 4720554c545241574944450a000000000000000000000000000000000000017c
[ 2.754849@2]
[ 2.754849@2]
[ 2.754851@2] hdmitx: edid: blk1 raw data
[ 2.754890@2] 020317f14410040301230907078301000065030c0010009f3d70a0d0a0155030
[ 2.754890@2] 203a00204f3100001a7e4800e0a0381f4040403a00204f31000018011d007251
[ 2.754890@2] d01e206e285500204f3100001e8c0ad08a20e02d10103e9600204f3100001800
[ 2.754890@2] 0000ff003431314b4b484e35393038310a0000000000000000000000000000ce
[ 2.754890@2]
[ 2.754890@2]
[ 2.754894@2] EDID Parser:
[ 2.754942@2] hdmitx: edid: find IEEEOUT
[ 2.754945@2] hdmitx: edid: check sum valid
[ 2.754946@2] hdmitx: edid: check sum valid
[ 2.754949@2] vinfo: error: invalid vinfo. current vmode is not supported
[ 2.754950@2] hdmitx: update RX hdr info 0
[ 2.756972@2] hdmitx: ddc rd8b error 0x3a 0x00 0x00
[ 2.759015@2] [RX]-receive ksv list len:1,depth:1,cas:0,dev:0
[ 2.759020@2] vinfo: error: invalid vinfo. current vmode is not supported
[ 2.759022@2] hdmitx: video: get current mode: invalid
[ 2.759024@2] hdmitx: update rx hdr info 0
[ 2.759043@2] hdmitx: edid: not find mapped vic
[ 2.759071@2] hdmitx: system: already init VIC = 0 Now VIC = 0
[ 2.759074@2] hdmitx: system: packet: can't get vendor data
[ 2.759076@2] hdmtix: set audio
[ 2.759085@2] hdmitx tx_aud_src = 0
[ 2.759111@2] hdmitx: fs = 0, cd = 4, tmds_clk = 0
[ 2.759114@2] hdmitx aud_n_para = 6144
[ 2.759132@2] hdmitx set channel status
[ 2.759192@2] hdmtix: set audio
[ 2.759200@2] hdmitx tx_aud_src = 0
[ 2.759225@2] hdmitx: fs = 0, cd = 4, tmds_clk = 0
[ 2.759226@2] hdmitx aud_n_para = 6144
[ 2.759244@2] hdmitx set channel status
[ 4.351638@0] console [ttyS0] enabled
[ 4.355751@0] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff80001f84c0
[ 4.362358@0] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
[ 4.372358@0] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: d0078000, ctrl: 0
[ 4.380279@2] dwc_otg_driver_probe host only, not probe usb_otg!!!
[ 4.386611@3] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff]
[ 4.396334@3] meson-gpu-clkgen: probe of c883c000.gpu_clk failed with error -16
[ 4.403818@3] hdmitx: system: hdmitx_hdcp_init
[ 4.408131@2] ESM HLD: Initializing...
[ 4.411670@2] ESM HLD: Registering device range 'esm'...
[ 4.416924@2] ESM HLD: Device range 'esm' has been registered.
[ 4.422710@2] ESM HLD: Creating class /sys/class/elliptic...
[ 4.428388@3] ESM HLD: The class /sys/class/elliptic has been created.
[ 4.434792@3] ESM HLD: Creating device 'esm'...
[ 4.439491@3] ESM HLD: Device 'esm' has been created.
[ 4.444259@3] ESM HLD: Done initializing the HLD driver.
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[ 4.465559@2] aml_vrtc rtc.32: rtc core: registered aml_vrtc as rtc0
[ 4.466962@3] secmon has 1 memory regions
[ 4.470315@3] secmon: share in base: 0xffffff8000404000, share out base: 0xffffff8000406000
[ 4.478532@3] secmon secmon.4: assigned reserved memory node linux,secmon ok
[ 4.485519@3] secmon: probe done
[ 4.489051@3] storage: storage in base: 0xffffff8001600000
[ 4.494137@3] storage: storage out base: 0xffffff8001680000
[ 4.499681@3] storage: storage block base: 0xffffff8001700000
[ 4.505349@3] storage: probe done!
[ 4.509290@2] aml_sd_emmc_probe: line 3558
[ 4.512770@2] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
[ 4.522740@2] aml_sd_emmc_reg_init 1146
[ 4.526016@2] get property: ocr_avail, value:0x00200080
[ 4.532472@2] get property: f_min, value:300000
[ 4.538565@2] get property: f_max, value:100000000
[ 4.544940@2] get property: max_req_size, value:0x00020000
[ 4.551430@2] get property: pinname, str:emmc
[ 4.557189@2] get property: card_type, value:1
[ 4.562905@2] get property: gpio_dat3, str:
[ 4.568314@2] get property: hw_reset, str:
[ 4.573790@2] emmc:pdata->caps = c0000d47
[ 4.577719@2] emmc:pdata->caps2 = 18060
[ 4.581528@2] storage 1, boot 1
[ 4.584613@2] get_storage_dev return 1
[ 4.628580@1] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 4.628815@1] aml_sd_emmc_probe: line 3558
[ 4.633229@1] aml_sd_emmc_reg_init 1146
[ 4.636682@1] get property: ocr_avail, value:0x00200080
[ 4.643116@1] get property: f_min, value:400000
[ 4.649231@1] get property: f_max, value:100000000
[ 4.655607@1] get property: max_req_size, value:0x00020000
[ 4.662081@1] get property: irq_in, value:3
[ 4.667768@1] get property: irq_out, value:5
[ 4.673475@1] get property: gpio_cd, str:
[ 4.678903@1] get property: pinname, str:sd
[ 4.684502@1] get property: jtag_pin, str:
[ 4.689942@1] get property: card_type, value:5
[ 4.695628@1] get property: gpio_dat3, str:
[ 4.701082@1] sd:pdata->caps = 7
[ 4.704251@1] sd:pdata->caps2 = 0
[ 4.738736@2] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 4.738771@4] [aml_is_card_insert] card IN
[ 4.743018@2] aml_sd_emmc_probe: line 3558
[ 4.747403@2] aml_sd_emmc_reg_init 1146
[ 4.750904@2] get property: ocr_avail, value:0x00200080
[ 4.757304@2] get property: f_min, value:400000
[ 4.763435@2] get property: f_max, value:200000000
[ 4.769817@2] get property: max_req_size, value:0x00020000
[ 4.776282@2] get property: pinname, str:sdio
[ 4.782065@2] get property: card_type, value:3
[ 4.787795@2] sdio:pdata->caps = 7810f
[ 4.791464@2] sdio:pdata->caps2 = 0
[ 4.805319@3] emmc: BKOPS_EN bit is not set
[ 4.814490@3] emmc: trying cali 0-th time(s)
[ 4.817425@3] emmc: delay[0]= 4600 padding= 2, bidx=4
[ 4.818127@3] emmc: delay[1]= 4600 padding= 2, bidx=4
[ 4.823148@3] emmc: delay[2]= 4400 padding= 3, bidx=4
[ 4.828132@3] emmc: delay[3]= 4800 padding= 1, bidx=4
[ 4.828586@2] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 4.828947@1] ion_dev has 1 memory regions
[ 4.840071@4] normal card in
[ 4.845825@3] emmc: delay[4]= 4800 padding= 1, bidx=4
[ 4.845844@1] fb: osd_init_module
[ 4.845976@1] fb: viu vsync irq: 35
[ 4.845981@1] fb: failed to init reserved memory
[ 4.845998@1] tv_vout: tv_set_current_vmode[759]fps_target_mode=16
[ 4.846001@1] tv_vout: mode is 16,sync_duration_den=1,sync_duration_num=60
[ 4.846010@1] tv_vout: TV mode 1080p60hz selected.
[ 4.846014@1]
[ 4.846014@1] vdac_enable: on:0,module_sel:8
[ 4.846020@1]
[ 4.846020@1] vdac_enable: on:0,module_sel:8
[ 4.846025@1] tv_vout: new mode =1080p60hz set ok
[ 4.846027@1] vout_serve: vinfo mode is: 1080p60hz
[ 4.846290@1] osd_rdma: osd_rdma_init: rdma_table p=0x74846000,op=0x74846000 , v=0xffffff800041e000
[ 4.846292@1] osd_rdma: osd rdma request irq as second interrput function!
[ 4.846309@1] fb: osd_probe vinfo:ffffffc001fbd8a8
[ 4.846315@1] fb: init fbdev bpp is:32
[ 4.925175@2] fb: use ion buffer for fb memory
[ 4.925181@3] emmc: delay[5]= 4800 padding= 1, bidx=4
[ 4.925183@3] emmc: delay[6]= 4600 padding= 2, bidx=4
[ 4.925185@3] emmc: delay[7]= 4800 padding= 1, bidx=4
[ 4.925188@3] emmc: calibration result @ 0: max(4800), min(4400)
[ 4.925191@3] emmc: line_delay =0x1000211, max_cal_result =4800
[ 4.925193@3] emmc: base_index_max 4, base_index_min 4
[ 4.925198@3] emmc: clk 100000000 SDR mode tuning start
[ 4.925781@2] meson-fb meson-fb.16: create ion_client ffffffc065398540, handle=ffffffc0641b3380
[ 4.925786@2] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 4.925793@2] fb: Frame buffer memory assigned at
[ 4.925793@2] fb: 0, phy: 0x0000000079300000, vir:0xffffff80018c4000, size=24900K
[ 4.925793@2]
[ 4.925796@2] fb: ---------------clear fb0 memory ffffff80018c4000
[ 4.927372@3] emmc: rx_tuning_result[0] = 10
[ 4.927869@3] emmc: rx_tuning_result[1] = 10
[ 4.928364@3] emmc: rx_tuning_result[2] = 10
[ 4.928916@3] emmc: rx_tuning_result[3] = 10
[ 4.929410@3] emmc: rx_tuning_result[4] = 10
[ 4.929905@3] emmc: rx_tuning_result[5] = 10
[ 4.930400@3] emmc: rx_tuning_result[6] = 10
[ 4.930897@3] emmc: rx_tuning_result[7] = 10
[ 4.931392@3] emmc: rx_tuning_result[8] = 10
[ 4.931446@3] emmc: best_win_start =0, best_win_size =9
[ 4.931448@3] emmc: sd_emmc_regs->gclock=0x100024a,sd_emmc_regs->gadjust=0x42000
[ 4.931452@3] emmc: gclock =0x100024a, gdelay=0x1000211, gadjust=0x42000
[ 4.931776@3] emmc: new HS200 MMC card at address 0001
[ 4.932262@1] emmc: clock 100000000, 8-bit-bus-width
[ 4.932262@1]
[ 4.932262@1] mmcblk0: emmc:0001 NCard 14.4 GiB
[ 4.932408@1] mmcblk0boot0: emmc:0001 NCard partition 1 4.00 MiB
[ 4.932542@1] mmcblk0boot1: emmc:0001 NCard partition 2 4.00 MiB
[ 4.932672@1] mmcblk0rpmb: emmc:0001 NCard partition 3 4.00 MiB
[ 4.933676@3] mmcblk0: unknown partition table
[ 4.934405@1] [mmc_read_partition_tbl] mmc read partition OK!
[ 4.934406@1] add_emmc_partition
[ 4.934665@3] [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
[ 4.934852@1] [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
[ 4.935041@3] [mmcblk0p03] cache offset 0x000006c00000, size 0x000020000000
[ 4.935217@1] [mmcblk0p04] env offset 0x000027400000, size 0x000000800000
[ 4.935392@3] [mmcblk0p05] logo offset 0x000028400000, size 0x000002000000
[ 4.935562@1] [mmcblk0p06] recovery offset 0x00002ac00000, size 0x000002000000
[ 4.935730@3] [mmcblk0p07] rsv offset 0x00002d400000, size 0x000000800000
[ 4.935899@1] [mmcblk0p08] tee offset 0x00002e400000, size 0x000000800000
[ 4.936067@3] [mmcblk0p09] crypt offset 0x00002f400000, size 0x000002000000
[ 4.936242@1] [mmcblk0p10] misc offset 0x000031c00000, size 0x000002000000
[ 4.936409@3] [mmcblk0p11] instaboot offset 0x000034400000, size 0x000020000000
[ 4.936579@1] [mmcblk0p12] boot offset 0x000054c00000, size 0x000002000000
[ 4.936760@3] [mmcblk0p13] system offset 0x000057400000, size 0x000080000000
[ 4.936899@2] fb: osd[0] canvas.idx =0x40
[ 4.936901@2] fb: osd[0] canvas.addr=0x79300000
[ 4.936903@2] fb: osd[0] canvas.width=7680
[ 4.936904@2] fb: osd[0] canvas.height=3240
[ 4.936906@2] fb: osd[0] frame.width=1920
[ 4.936907@2] fb: osd[0] frame.height=1080
[ 4.936932@1] [mmcblk0p14] data offset 0x0000d7c00000, size 0x0002c5400000
[ 4.936962@1] card key: card_blk_probe.
[ 4.936966@1] emmc_key_init:527 emmc key lba_start:0x12020,lba_end:0x12220
[ 4.936969@1] emmc key: emmc_key_init:552 ok.
[ 4.937234@2] amlmmc_dtb_init: register dtb chardev
[ 4.937325@2] amlmmc_dtb_init: register dtb chardev OK
[ 4.937325@2] Exit aml_emmc_partition_ops OK.
[ 4.938486@2] mmcblk0boot1: unknown partition table
[ 4.939438@2] mmcblk0boot0: unknown partition table
[ 4.939706@2] clear_emmc_wait_flag
[ 5.023085@2] sd: new high speed SDHC card at address aaaa
[ 5.023497@2] sd: clock 50000000, 4-bit-bus-width
[ 5.023497@2]
[ 5.023498@2] mmcblk1: sd:aaaa SL08G 7.40 GiB
[ 5.024591@2] mmcblk1: p1 p2
[ 5.054684@1] Console: switching to colour frame buffer device 240x67
[ 5.518571@1] fb: osd probe OK
[ 5.523111@3] ge2d: ge2d_init_module
[ 5.527367@3] ge2d: ge2d_dev major:242
[ 5.532066@3] ge2d: ge2d clock is 400 MHZ
[ 5.536215@3] ge2d: ge2d: pdev=ffffffc065275c00, irq=182, rstc=0xffffffc0653a2900, clk=ffffffc065240800
[ 5.544189@3] ge2d: mapped phy: 0xd0160000
[ 5.548319@3] ge2d: ge2d start monitor
[ 5.552454@0] ge2d: ge2d workqueue monitor start
[ 5.552801@3] codec:Amlogic A/V streaming port init
[ 5.554532@3] codec:get gate demux control ok ffffffc0640f9900
[ 5.554537@3] codec:get gate parser_top control ok ffffffc0640f9980
[ 5.554542@3] codec:get gate vpu_intr control ok ffffffc0640f9a00
[ 5.554548@3] codec:get gate vdec control ok ffffffc0640f9a80
[ 5.555149@3] codec:[tsync_pcr_init]init success.
[ 5.555150@3] codec:amvideocap_init_module
[ 5.555273@3] codec:amvideocap_probe,amvideocap
[ 5.555276@3] codec:use cma buf.
[ 5.555278@3] codec:amvideocap_dev_register
[ 5.556893@3] amvenc_avc_probe -- reserved memory config fail.
[ 5.556897@3] amvenc_avc - cma memory pool size: 40 MB
[ 5.556917@3] encode_wq_init.
[ 5.556922@3] encode start monitor.
[ 5.556978@1] encode workqueue monitor start.
[ 5.557460@3] jpegenc module init
[ 5.557754@3] codec:picdec_driver_probe called.
[ 5.557757@3] picdec has 1 memory regions
[ 5.557782@3] codec:picdec_driver_probe done.
[ 5.558901@3] codec:create_ge2d_work_queue video task ok
[ 5.559317@3] codec:used fix clk for vdec clk source!
[ 5.559321@3] codec:register clk_set_setting cpu[34]
[ 5.559646@3] vpu_init
[ 5.559807@3] vpu_probe
[ 5.559811@3] HevcEnc reserved memory config fail.
[ 5.559815@3] HevcEnc - cma memory pool size: 64 MB
[ 5.559817@3] HevcEnc - wave420l_irq: 219
[ 5.559856@3] vpu base address get from platform driver physical base addr=0xc8810000, virtual base=0xffffff8000588000
[ 5.560205@3] success to probe vpu device with video memory from cma
[ 5.560345@3] DI: di_module_init ok.
[ 5.560349@3] DI: di_module_init: major 235
[ 5.560544@3] DI: di_probe
[ 5.560722@3] deinterlace has 1 memory regions
[ 5.560758@3] deinterlace deinterlace.26: assigned reserved memory node linux,di ok
[ 5.560781@3] di_irq:78,timerc_irq:38
[ 5.725990@3] rdma_register, rdma_table_addr ffffff8000581000 rdma_table_addr_phy 74848000 reg_buf ffffffc065298000
[ 5.735671@3] rdma_register success, handle 1 table_size 8192
[ 5.741349@3] DI: di_probe allocate rdma channel 1.
[ 5.746227@3] DI: DI hw version 2.
[ 5.751135@3] 0x000000db:Y=db,U=0,V=0
[ 5.756032@3] 0x000000dc:Y=dc,U=0,V=0
[ 5.760912@3] 0x000000dd:Y=dd,U=0,V=0
[ 5.765778@3] 0x000000de:Y=de,U=0,V=0
[ 5.770539@3] 0x000000df:Y=df,U=0,V=0
[ 5.775191@3] 0x000000e0:Y=e0,U=0,V=0
[ 5.779786@3] 0x000000e1:Y=e1,U=0,V=0
[ 5.784284@3] 0x000000e2:Y=e2,U=0,V=0
[ 5.788734@3] 0x000000e3:Y=e3,U=0,V=0
[ 5.793176@3] 0x000000f0:Y=f0,U=0,V=0
[ 5.797574@3] 0x000000f1:Y=f1,U=0,V=0
[ 5.801920@3] 0x000000f2:Y=f2,U=0,V=0
[ 5.806265@3] 0x000000f3:Y=f3,U=0,V=0
[ 5.810568@3] 0x000000f4:Y=f4,U=0,V=0
[ 5.814793@3] 0x000000f5:Y=f5,U=0,V=0
[ 5.818966@3] 0x000000f6:Y=f6,U=0,V=0
[ 5.823092@3] 0x000000f7:Y=f7,U=0,V=0
[ 5.827182@3] 0x000000f8:Y=f8,U=0,V=0
[ 5.831235@3] 0x000000f9:Y=f9,U=0,V=0
[ 5.835202@3] 0x000000fa:Y=fa,U=0,V=0
[ 5.839095@3] 0x000000fb:Y=fb,U=0,V=0
[ 5.842948@3] 0x000000fc:Y=fc,U=0,V=0
[ 5.846943@3] DI: di_probe here.
[ 5.851233@3] efusekeynum: 4
[ 5.855028@3] efusekeyname: mac offset: 0 size: 6
[ 5.859557@3] efusekeyname: mac_bt offset: 6 size: 6
[ 5.865898@3] efusekeyname: mac_wifi offset: 12 size: 6
[ 5.872309@3] efusekeyname: usid offset: 18 size: 16
[ 5.879082@0] efuse efuse.10: probe OK!
[ 5.883173@3] key unify config unifykey-num is 14
[ 5.887154@3] key unify fact unifykey-num is 14
[ 5.891642@3] aml_unifykeys_probe:1273=============unifykey_devno:e900000
[ 5.898736@0] 6unifykey: device unifykeys created ok
[ 5.903495@3] 6aml_unifykeys_init done!
[ 5.907207@3] PPMGRDRV: warn: ppmgr module init func called
[ 5.912925@3] PPMGRDRV: err: ppmgr_driver_probe called
[ 5.917816@3] ppmgr has 1 memory regions
[ 5.921764@3] PPMGRDRV: info: ppmgr_dev major:232
[ 5.926792@0] PPMGRDRV: info: ppmgr_probe done
[ 5.931346@3] amlogic rfkill init
[ 5.935267@3] enter bt_probe of_node
[ 5.939072@3] not get gpio_en
[ 5.942786@3] power on valid level is high
[ 6.359142@0] ionvideo-000: V4L2 device registered as video13
[ 6.366721@0] ionvid: info: Video Technology Magazine Ion Video
[ 6.372609@0] ionvid: info: Capture Board ver 1.0 successfully loaded
[ 6.378989@0] audio_dsp: [dsp]register dsp to char divece(257)
[ 6.385698@0] amaudio: amaudio: driver amaudio succuess!
[ 6.390405@0] amlvid:err: amlvideo_init called
[ 6.394235@1] amlvid:err: amlvideo_create_instance called
[ 6.401950@1] amlvid:err: v4l2_dev.name=:amlvideo-000
[ 6.406929@0] amlvideo-000: V4L2 device registered as video10
[ 6.412916@0] [RX]-hdmirx: hdmirx_init.
[ 6.416901@0] ESM HLD: Initializing...
[ 6.420851@0] ESM HLD: Registering device range 'esm_rx'...
[ 6.425371@0] ESM HLD: Device range 'esm_rx' has been registered.
[ 6.431446@0] ESM HLD: Creating class /sys/class/elliptic_rx...
[ 6.437407@0] ESM HLD: The class /sys/class/elliptic_rx has been created.
[ 6.444008@0] ESM HLD: Creating device 'esm_rx'...
[ 6.449017@1] ESM HLD: Device 'esm_rx' has been created.
[ 6.453997@1] ESM HLD: Done initializing the HLD driver.
[ 6.459297@1] [viuin..]viuin_init_module viuin module init
[ 6.465226@0] [viuin..]viuin_probe probe ok.
[ 6.469089@1] module init
[ 6.472839@1]
[ 6.472839@1] VECM probe start
[ 6.480188@0] aml_vecm_probe: ok
[ 6.484425@0] saradc c1108680.saradc: initialized by BL30
[ 6.488061@0] saradc c1108680.saradc: calibration start:
[ 6.493130@0] saradc c1108680.saradc: nominal=0, value=4
[ 6.498346@0] saradc c1108680.saradc: nominal=256, value=251
[ 6.503969@0] saradc c1108680.saradc: nominal=512, value=500
[ 6.509578@0] saradc c1108680.saradc: nominal=768, value=748
[ 6.515165@0] saradc c1108680.saradc: nominal=1023, value=997
[ 6.520826@0] saradc c1108680.saradc: calibration end: coef=4219
[ 6.527047@1] remote: Driver init
[ 6.530943@1] remote: platform_data g_remote_ao_offset=580
[ 6.535477@1] remote: platform_data irq =228
[ 6.539740@1] remote: set drvdata completed
[ 6.545673@1] remote: device_create_file completed
[ 6.550317@1] input: aml_keypad as /devices/meson-remote.12/input/input0
[ 6.555958@1] remote: input_register_device completed
[ 6.561807@1] remote: set_remote_mode[74]
[ 6.566922@1] remote: remote config major:229
[ 6.571466@1] remote: physical address:0x63574000
[ 6.576420@1] gpio-key gpio_keypad.48: gpio_key: 0 name(power) pin()
[ 6.581504@1] gpio-key gpio_keypad.48: amlogic_gpio_name_map_num pin 0!::
[ 6.588221@1] gpio-key gpio_keypad.48: gpio_key: 0 power(147)
[ 6.593938@1] gpio-key gpio_keypad.48: start setup_timer
[ 6.599181@1] gpio-key gpio_keypad.48: power key(116) registed.
[ 6.605316@0] input: gpio_keypad as /devices/gpio_keypad.48/input/input1
[ 6.611978@0] gpio-key gpio_keypad.48: gpio keypad register input device completed.
[ 6.619280@0] input input1: gpio keypad major:228
[ 6.624937@0] Sensor: lsm303d_init
[ 6.629952@0] Sensor: stk8313_init
[ 6.634693@0] Sensor: stk831x_init
[ 6.639395@1] Sensor: mxc622x_acc_init
[ 6.644060@0] Sensor: mxc6255xc_acc_init
[ 6.648680@0] Sensor: l3gd20_gyr_init
[ 6.654381@3] cpuinfo: probe done
[ 6.659258@0] defendkey c8834500.defendkey: defendkey_devno:e300000
[ 6.664681@3] defendkey c8834500.defendkey: defendkey: device defendkey created ok
[ 6.672145@0] defendkey: driver init
[ 6.677447@0] input: cec_input as /devices/virtual/input/input2
[ 6.682658@3] cectx aocec: aml_cec_probe(): no hdmirx reg resource
[ 6.688350@3] cectx aocec: aml_cec_probe(): no hhi reg resource
[ 6.694381@3] cectx aocec: aml_cec_probe(): can't find hdmirx
[ 6.701065@3] cec: wake up flag:0
[ 6.706140@3] aml_aes_dma c883e000.aml_aes: Aml AES_dma
[ 6.708599@1] input input1: key 116 up
[ 6.716007@0] aml_tdes_dma c883e000.aml_tdes: Aml TDES_dma
[ 6.721420@3] aml_sha_dma c883e000.aml_sha: Aml SHA1/SHA224/SHA256 dma
[ 6.728945@0] aml_codec_T9015 c8832000.t9015: aml_T9015_audio_codec_probe
[ 6.736957@3] aml_pcm_dai: pcm mode detection =1
[ 6.742185@0] aml_spdif_dai: enterd aml_spdif_play,set_clock:-1,sample_rate=4
[ 6.748374@0] aml_spdif_dai: set normal 512 fs /4 fs
[ 6.753329@0] aml_audio_hw: IEC958 16bit
[ 6.757948@0] hdmitx: audio: aout notify rate 48000
[ 6.762584@0] hdmitx: audio: aout notify size 16
[ 6.767146@0] hdmitx: audio: aout notify format CT_PCM
[ 6.771781@0] hdmtix: set audio
[ 6.776303@0] hdmitx tx_aud_src = 0
[ 6.780819@0] hdmitx: fs = 3, cd = 4, tmds_clk = 0
[ 6.785312@0] hdmitx aud_n_para = 6144
[ 6.789810@0] hdmitx set channel status
[ 6.794261@0] hdmitx: audio: Audio Type: PCM
[ 6.798664@0] hdmitx: audio: set audio param
[ 7.008775@3] aml_snd_card: headphone detection disable=1
[ 7.013239@3] aml_snd_card: no spk event delay time set
[ 7.018783@3] aml_snd_m8_card aml_m8_snd.47: T9015-audio-hifi <-> I2S.40 mapping ok
[ 7.026321@3] aml_snd_m8_card aml_m8_snd.47: dit-hifi <-> SPDIF.41 mapping ok
[ 7.032971@3] aml_pcm: enter aml_pcm_new dai->name: PCM.42 dai->id: 0
[ 7.039377@3] aml_snd_m8_card aml_m8_snd.47: pcm2bt-pcm <-> PCM.42 mapping ok
[ 7.046281@3] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTL
[ 7.053890@3] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
[ 7.062670@3] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTR
[ 7.070255@3] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[ 7.086280@2] aml_snd_card: audio use jtag pinmux as i2s output, read val =0
WARNING: Unimplemented Sip Call: 0x82000036
[ 7.097853@2] GACT probability NOT on
[ 7.102844@2] Mirror/redirect action on
[ 7.107759@2] u32 classifier
[ 7.112641@2] Actions configured
[ 7.117494@2] Netfilter messages via NETLINK v0.30.
[ 7.122442@2] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 7.128546@0] ctnetlink v0.93: registering with nfnetlink.
[ 7.134282@0] xt_time: kernel timezone is -0000
[ 7.139477@0] ipip: IPv4 over IPv4 tunneling driver
[ 7.145377@0] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.150615@0] arp_tables: (C) 2002 David S. Miller
[ 7.155684@0] TCP: cubic registered
[ 7.160657@0] Initializing XFRM netlink socket
[ 7.166592@0] NET: Registered protocol family 10
[ 7.172805@0] mip6: Mobile IPv6
[ 7.177828@0] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.183177@0] sit: IPv6 over IPv4 tunneling driver
[ 7.189714@0] NET: Registered protocol family 17
[ 7.194867@0] NET: Registered protocol family 15
[ 7.200017@0] Bridge firewalling registered
[ 7.204987@0] l2tp_core: L2TP core driver, V2.0
[ 7.209833@0] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 7.214792@0] l2tp_netlink: L2TP netlink interface
[ 7.219768@0] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 7.225575@0] l2tp_debugfs: L2TP debugfs support
[ 7.230590@0] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 7.236752@0] NET: Registered protocol family 35
[ 7.241985@0] Key type dns_resolver registered
[ 7.247876@0] Registering SWP/SWPB emulation handler
[ 7.255528@0] bio: create slab <bio-1> at 1
[ 7.261887@0] Btrfs loaded
[ 7.267077@0] BTRFS: selftest: Running btrfs free space cache tests
[ 7.272821@0] BTRFS: selftest: Running extent only tests
[ 7.278079@0] BTRFS: selftest: Running bitmap only tests
[ 7.283361@0] BTRFS: selftest: Running bitmap and extent tests
[ 7.289126@0] BTRFS: selftest: Free space cache tests finished
[ 7.294874@0] BTRFS: selftest: Running extent buffer operation tests
[ 7.301009@0] BTRFS: selftest: Running btrfs_split_item tests
[ 7.311038@0] BTRFS: selftest: Running find delalloc tests
[ 7.527698@0] BTRFS: selftest: Running btrfs_get_extent tests
[ 7.533205@0] BTRFS: selftest: Running hole first btrfs_get_extent test
[ 7.628652@0] AppArmor: AppArmor sha1 policy hashing enabled
[ 7.633614@0] regulator-dummy: disabling
[ 8.340989@0] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 8.345932@0] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 8.354047@0] xhci-hcd xhci-hcd.0.auto: irq 62, io mem 0xc9000000
[ 8.359851@0] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.366601@0] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.373946@0] usb usb1: Product: xHCI Host Controller
[ 8.378979@0] usb usb1: Manufacturer: Linux 3.14.29 xhci-hcd
[ 8.384540@0] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 8.390354@0] hub 1-0:1.0: USB hub found
[ 8.395506@0] hub 1-0:1.0: 3 ports detected
[ 8.400928@0] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 8.406084@0] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 8.413978@0] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 8.420736@0] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.428054@0] usb usb2: Product: xHCI Host Controller
[ 8.433267@0] usb usb2: Manufacturer: Linux 3.14.29 xhci-hcd
[ 8.438672@0] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 8.444508@3] hub 2-0:1.0: USB hub found
[ 8.449757@3] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 8.457284@4] console [netcon0] enabled
[ 8.463555@4] netconsole: network logging started
[ 8.469793@4] aml_vrtc rtc.32: setting system clock to 2015-01-01 00:00:16 UTC (1420070416)
[ 8.480213@4] gxbb_pm: enter meson_pm_probe!
[ 8.486551@4] gxbb_pm: meson_pm_probe done
[ 8.493252@3] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 8.500856@3] platform thermal: Driver aml-thermal requests probe deferral
[ 8.507797@3] aml_istbt_dev_ready NULL
[ 8.513211@3] ALSA device list:
[ 8.518509@3] #0: AML-M8AUDIO
[ 8.524457@3] Freeing unused kernel memory: 1180K (ffffffc001e14000 - ffffffc001f3b000)
[ 8.565302@2] systemd-udevd[2066]: starting version 215
[ 8.572056@2] random: systemd-udevd urandom read with 43 bits of entropy available
[ 8.718652@4] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 8.866917@5] usb 1-1: New USB device found, idVendor=05ac, idProduct=1006
[ 8.874936@5] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8.883268@5] usb 1-1: Product: Keyboard Hub
[ 8.889924@5] usb 1-1: Manufacturer: Apple, Inc.
[ 8.896556@5] usb 1-1: SerialNumber: 000000000000
[ 8.926071@0] hub 1-1:1.0: USB hub found
[ 8.931690@0] hub 1-1:1.0: 3 ports detected
[ 8.938599@1] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 8.946557@1] platform thermal: Driver aml-thermal requests probe deferral
[ 9.208659@4] usb 1-1.2: new low-speed USB device number 3 using xhci-hcd
[ 9.334732@4] usb 1-1.2: New USB device found, idVendor=05ac, idProduct=0220
[ 9.343316@4] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 9.352306@4] usb 1-1.2: Product: Apple Keyboard
[ 9.359460@4] usb 1-1.2: Manufacturer: Apple, Inc
[ 9.367773@2] usb 1-1.2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 9.377282@2] usb 1-1.2: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 9.409865@1] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 9.418650@1] platform thermal: Driver aml-thermal requests probe deferral
[ 9.419497@6] input: Apple, Inc Apple Keyboard as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.2/1-1.2:1.0/0003:05AC:0220.0001/input/input3
[ 9.419845@5] apple 0003:05AC:0220.0001: input,hidraw0: USB HID v1.11 Keyboard [Apple, Inc Apple Keyboard] on usb-xhci-hcd.0.auto-1.2/input0
[ 9.420837@5] input: Apple, Inc Apple Keyboard as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.2/1-1.2:1.1/0003:05AC:0220.0002/input/input4
[ 9.421128@5] apple 0003:05AC:0220.0002: input,hidraw1: USB HID v1.11 Device [Apple, Inc Apple Keyboard] on usb-xhci-hcd.0.auto-1.2/input1
[ 9.483167@1] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 9.483179@1] platform thermal: Driver aml-thermal requests probe deferral
[ 9.508669@7] usb 1-1.3: new low-speed USB device number 4 using xhci-hcd
[ 9.555020@1] EXT4-fs (mmcblk1p2): mounted filesystem with writeback data mode. Opts: data=writeback
[ 9.608466@0] random: nonblocking pool is initialized
[ 9.619515@4] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c05a
[ 9.630119@4] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 9.641145@4] usb 1-1.3: Product: USB Optical Mouse
[ 9.650304@4] usb 1-1.3: Manufacturer: Logitech
[ 9.659988@0] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 9.696699@0] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0003/input/input5
[ 9.712861@0] hid-generic 0003:046D:C05A.0003: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 9.728889@6] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 9.741375@6] platform thermal: Driver aml-thermal requests probe deferral
[ 10.006652@7] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[ 10.025406@7] systemd[1]: Detected architecture 'arm64'.
[ 10.079336@1] systemd[1]: Inserted module 'autofs4'
[ 10.089502@1] systemd[1]: Set hostname to <amlogic-s905x>.
[ 10.144510@2] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 10.381840@3] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[ 10.401854@3] systemd[1]: Expecting device dev-ttyS0.device...
[ 10.420897@3] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 10.432468@3] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 10.443734@3] systemd[1]: Starting Remote File Systems (Pre).
[ 10.462308@3] systemd[1]: Reached target Remote File Systems (Pre).
[ 10.472141@3] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 10.494487@3] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 10.507741@3] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 10.519734@3] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 10.531540@3] systemd[1]: Starting Paths.
[ 10.550535@3] systemd[1]: Reached target Paths.
[ 10.559947@3] systemd[1]: Starting Encrypted Volumes.
[ 10.578894@3] systemd[1]: Reached target Encrypted Volumes.
[ 10.588172@3] systemd[1]: Expecting device dev-disk-by\x2dlabel-BOOT.device...
[ 10.608740@3] systemd[1]: Starting Root Slice.
[ 10.627656@3] systemd[1]: Created slice Root Slice.
[ 10.636910@3] systemd[1]: Starting Delayed Shutdown Socket.
[ 10.655805@3] systemd[1]: Listening on Delayed Shutdown Socket.
[ 10.665307@3] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 10.685459@3] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 10.696116@3] systemd[1]: Starting Journal Socket (/dev/log).
[ 10.714749@3] systemd[1]: Listening on Journal Socket (/dev/log).
[ 10.724201@3] systemd[1]: Starting User and Session Slice.
[ 10.742230@3] systemd[1]: Created slice User and Session Slice.
[ 10.751145@3] systemd[1]: Starting udev Control Socket.
[ 10.768321@3] systemd[1]: Listening on udev Control Socket.
[ 10.776645@3] systemd[1]: Starting udev Kernel Socket.
[ 10.793501@3] systemd[1]: Listening on udev Kernel Socket.
[ 10.801740@3] systemd[1]: Starting Journal Socket.
[ 10.818498@3] systemd[1]: Listening on Journal Socket.
[ 10.826747@3] systemd[1]: Starting System Slice.
[ 10.843183@3] systemd[1]: Created slice System Slice.
[ 10.851188@3] systemd[1]: Starting system-systemd\x2dfsck.slice.
[ 10.867986@3] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 10.876788@3] systemd[1]: Starting Increase datagram queue length...
[ 10.895048@3] systemd[1]: Starting Restore / save the current clock...
[ 10.917196@3] systemd[1]: Mounting Huge Pages File System...
[ 10.933947@3] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 10.954817@3] systemd[1]: Mounting Debug File System...
[ 10.971138@3] systemd[1]: Starting udev Coldplug all Devices...
[ 10.988084@3] systemd[1]: Mounting POSIX Message Queue File System...
[ 11.009353@3] systemd[1]: Started Set Up Additional Binary Formats.
[ 11.017382@3] systemd[1]: Starting LSB: Set keymap...
[ 11.033419@3] systemd[1]: Starting system-serial\x2dgetty.slice.
[ 11.048514@3] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 11.056420@3] systemd[1]: Starting system-getty.slice.
[ 11.071008@3] systemd[1]: Created slice system-getty.slice.
[ 11.080819@3] systemd[1]: Starting Load Kernel Modules...
[ 11.096469@3] systemd[1]: Started File System Check on Root Device.
[ 11.104027@3] systemd[1]: Starting Slices.
[ 11.116311@2] fuse init (API version 7.22)
[ 11.120577@2] Triggered SDIO WiFi power on and bus rescan.
[ 11.120596@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 11.139007@3] systemd[1]: Reached target Slices.
[ 11.153929@3] systemd[1]: Mounted POSIX Message Queue File System.
[ 11.168359@3] systemd[1]: Mounted Debug File System.
[ 11.182157@3] systemd[1]: Mounted Huge Pages File System.
[ 11.196769@3] systemd[1]: Started Increase datagram queue length.
[ 11.212435@3] systemd[1]: Started Restore / save the current clock.
[ 11.228299@3] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 11.249266@3] systemd[1]: Started LSB: Set keymap.
[ 11.257518@3] systemd[1]: Time has been changed
[ 11.291626@3] systemd[1]: Started udev Coldplug all Devices.
[ 11.319183@3] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 11.335946@3] systemd[1]: Starting Syslog Socket.
[ 11.350351@3] systemd[1]: Listening on Syslog Socket.
[ 11.357277@3] systemd[1]: Starting Journal Service...
[ 11.380467@3] systemd[1]: Started Journal Service.
[ 11.428639@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 11.444693@3] systemd-udevd[2168]: starting version 215
[ 11.770548@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 11.781222@6] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 11.793115@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 11.808671@3] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 11.861559@0] ionvid: info: ionvideo open
[ 11.899340@4] aml_audio_i2s_mute_flag: flag=0
[ 11.906942@4] aml_audio_set_spdif_mute: flag=0
[ 11.914372@4] aml_snd_card: aml_m8_set_spk: aml_m8_spk_enabled=0
[ 11.923267@7] sdio: clk 200000000 SDR mode tuning start
[ 11.930802@7] sdio: rx_tuning_result[0] = 10
[ 11.931030@7] sdio: rx_tuning_result[1] = 10
[ 11.931259@7] sdio: rx_tuning_result[2] = 10
[ 11.931492@7] sdio: rx_tuning_result[3] = 10
[ 11.931519@7] sdio: best_win_start =0, best_win_size =4
[ 11.931522@7] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 11.931530@7] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 11.935103@7] sdio: queuing unknown CIS tuple 0x91 (3 bytes)
[ 11.935135@7] sdio: new ultra high speed SDR104 SDIO card at address 0001
[ 11.935528@5] sdio: clock 200000000, 4-bit-bus-width
[ 11.935528@5]
[ 11.935529@5] [sdio_reinit] finish
[ 12.007434@6] aml_nftl_dev: module license 'Proprietary' taints kernel.
[ 12.007437@6] Disabling lock debugging due to kernel taint
[ 12.009417@5] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 12.009430@5] platform thermal: Driver aml-thermal requests probe deferral
[ 12.058611@1] ionvid: info: ionvideo_stop_generating!!!!
[ 12.064461@1] ionvid: info: ionvideo release
[ 12.069980@5] cfg80211: Calling CRDA to update world regulatory domain
[ 12.166246@5] dhd_module_init: in
[ 12.172751@5] ======== bcm_wlan_set_plat_data ========
[ 12.179188@5] host_oob_irq: 100
[ 12.185540@5] host_oob_irq_flags=0x414
[ 12.191877@5] dhd_wifi_platform_load: Enter
[ 12.198209@0] Power-up adapter 'DHD generic adapter'
[ 12.204490@0] wifi_platform_set_power = 1
[ 12.209749@0] ======== PULL WL_REG_ON HIGH! ========
[ 12.214925@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 12.271209@7] EXT4-fs (mmcblk1p2): re-mounted. Opts: commit=600,errors=remount-ro
[ 12.357270@3] BT_RADIO going: on
[ 12.357273@3] BCM_BT: going ON
[ 12.393612@5] Adding 131068k swap on /var/swap. Priority:-1 extents:1 across:131068k SSFS
[ 12.402445@4] cfg80211: World regulatory domain updated:
[ 12.402452@4] cfg80211: DFS Master region: unset
[ 12.402452@4] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.402459@4] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 12.402462@4] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 12.402465@4] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 12.402468@4] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 12.402470@4] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 12.402473@4] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[ 12.402476@4] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 12.402478@4] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 12.421478@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 12.673634@5] systemd-journald[2166]: Received request to flush runtime journal from PID 1
[ 12.928648@7] wifi_platform_bus_enumerate device present 1
[ 12.935441@7] ======== Card detection to detect SDIO card! ========
[ 12.935448@7] sdio_reset_comm():
[ 12.963634@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 12.973164@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 12.982533@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 12.993892@1] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 13.093208@7] sdio: clk 200000000 SDR mode tuning start
[ 13.100062@7] sdio: rx_tuning_result[0] = 10
[ 13.106828@7] sdio: rx_tuning_result[1] = 10
[ 13.113600@0] sdio: rx_tuning_result[2] = 10
[ 13.119410@0] sdio: rx_tuning_result[3] = 10
[ 13.124723@0] sdio: best_win_start =0, best_win_size =4
[ 13.130011@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 13.137067@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 13.143210@0] [sdio_reinit] finish
[ 13.149010@5] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 13.157902@5] platform thermal: Driver aml-thermal requests probe deferral
[ 13.164950@0] bcmsdh_register: register client driver
[ 13.165046@0] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[ 13.165119@0] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[ 13.165121@0] bus num (host idx)=0, slot num (rca)=1
[ 13.165123@0] found adapter info 'DHD generic adapter'
[ 13.165190@0] sdioh_attach: set sd_f2_blocksize 128
[ 13.165563@0] dhdsdio_probe : no mutex held. set lock
[ 13.165689@0] F1 signature read @0x18000000=0x15264345
[ 13.169162@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 13.169856@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 13.169936@0] dhd_conf_set_chiprev: chip=0x4345, chiprev=6
[ 13.169979@0] dhd_conf_set_conf_path_by_nv_path: config_path=/lib/firmware/brcm/config.txt
[ 13.179951@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 13.179955@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 13.180112@0] dhd_conf_read_config: PM = 0
[ 13.180617@0] wl_create_event_handler(): thread:wl_event_handler:95a started
[ 13.180623@1] tsk Enter, tsk = 0xffffff8003227940
[ 13.180771@0] dhd_attach(): thread:dhd_watchdog_thread:95b started
[ 13.180824@0] dhd_attach(): thread:dhd_dpc:95c started
[ 13.180844@3] dhd_dpc_thread: set dpc_cpucore 0 from config.txt
[ 13.180884@1] dhd_attach(): thread:dhd_rxf:95d started
[ 13.180893@1] dhd_deferred_work_init: work queue initialized
[ 13.193500@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 13.193500@1] Compiled in drivers/net/wireless/bcmdhd
[ 13.193991@1] Register interface [wlan0] MAC: 44:2c:05:f5:4a:5a
[ 13.193991@1]
[ 13.193997@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 13.194042@1] bcmsdh_oob_intr_unregister: Enter
[ 13.194044@1] bcmsdh_oob_intr_unregister: irq is not registered
[ 13.194051@1] dhd_txglom_enable: enable 0
[ 13.194054@1] dhd_conf_set_txglom_params: swtxglom=0, txglom_ext=0
[ 13.194056@1] dhd_conf_set_txglom_params: txglom_bucket_size=0
[ 13.194058@1] dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0, bus_txglom=0
[ 13.194059@1] dhd_conf_set_txglom_params: tx_in_rx=1, tx_max_offset=0
[ 13.194061@1] dhd_bus_devreset: WLAN OFF DONE
[ 13.194112@1] wifi_platform_set_power = 0
[ 13.194114@1] ======== PULL WL_REG_ON LOW! ========
[ 13.194117@1] dhdsdio_probe : the lock is released.
[ 13.194188@1] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[ 13.194224@1] dhd_module_init: Exit err=0
[ 13.227778@7] Bluetooth: Core ver 2.18
[ 13.227829@7] NET: Registered protocol family 31
[ 13.227831@7] Bluetooth: HCI device and connection manager initialized
[ 13.227863@7] Bluetooth: HCI socket layer initialized
[ 13.227870@7] Bluetooth: L2CAP socket layer initialized
[ 13.227899@7] Bluetooth: SCO socket layer initialized
[ 13.230585@7] Bluetooth: Generic Bluetooth SDIO driver ver 0.1
[ 13.495230@3] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 13.495241@3] platform thermal: Driver aml-thermal requests probe deferral
[ 13.803176@0] aml_audio_i2s_mute_flag: flag=0
[ 13.803189@0] aml_audio_set_spdif_mute: flag=0
[ 13.803200@0] aml_snd_card: aml_m8_set_spk: aml_m8_spk_enabled=0
[ 13.929353@1] vout_serve: vmode set to 720p60hz
[ 13.929353@1]
[ 13.940195@1] fb: current vmode=1080p60hz
[ 13.945331@1] tv_vout: tv_set_current_vmode[759]fps_target_mode=10
[ 13.951037@1] tv_vout: mode is 10,sync_duration_den=1,sync_duration_num=60
[ 13.957780@1] tv_vout: TV mode 720p60hz selected.
[ 13.963000@1]
[ 13.963000@1] vdac_enable: on:0,module_sel:8
[ 13.973355@1]
[ 13.973355@1] vdac_enable: on:0,module_sel:8
[ 13.983709@1] tv_vout: new mode =720p60hz set ok
[ 13.988754@1] vout_serve: vinfo mode is: 720p60hz
[ 13.993781@1] vout_serve: new mode 720p60hz
[ 13.993781@1] set ok
[ 14.004452@1] hdmitx: video: get current mode: 720p60hz
[ 14.009600@1] hdmitx: update rx hdr info 0
[ 14.014566@1] hdmitx: get ext_name
[ 14.019550@1] hdmitx: system: already init VIC = 0 Now VIC = 4
[ 14.024738@1] hdmitx: rx no SCDC present indicator
[ 14.031762@1] hdmitx: ddc rd8b error 0x54 0x01
[ 14.038752@1] hdmitx: ddc rd8b error 0x54 0x01
[ 14.043618@1] hdmirx version is 1.4 or below
[ 14.048448@1] hdmitx div40: 0
[ 14.078602@1] hdmitx: system: set mode VIC 4 (cd0,cs0,pm1,vd0,1)
[ 14.083834@1] hdmitx: system: set pll
[ 14.090689@1] hdmitx: ddc w1b error 0x54 0x20 0x00
[ 14.097500@1] hdmitx: ddc w1b error 0x54 0x20 0x00
[ 14.104297@1] hdmitx: ddc rd8b error 0x54 0x21
[ 14.109179@1] hdmitx: system: param->VIC:4
[ 14.113899@1] hdmitx: set clk: VIC = 4 cd = 4
[ 14.118649@1] config HPLL = 2970000
[ 14.123306@1] HPLL: 0xc000027b
[ 14.127897@1] config HPLL done
[ 14.132489@1] set_hpll_od3_clk_div[441] div = 6
[ 14.137101@1] j = 2 vid_clk_div = 1
[ 14.141747@1] hdmitx: set enc for VIC: 4
[ 14.146239@1] hdmitx_set_hw[4867] set VIC = 4
[ 14.280606@1] hdmitx: system: phy setting done
[ 14.284626@1] Sink is HDMI device
[ 14.284636@1] hdmitx: system: packet: can't get vendor data
[ 14.284640@1] hdmtix: set audio
[ 14.284650@1] hdmitx tx_aud_src = 0
[ 14.284678@1] hdmitx: fs = 3, cd = 4, tmds_clk = 74250
[ 14.284680@1] hdmitx aud_n_para = 6144
[ 14.284699@1] hdmitx set channel status
[ 14.284760@1] hdmitx: audio: Audio Type: PCM
[ 14.284766@1] fb: current vmode=720p60hz
[ 14.388721@3] fb: osd[0] canvas.idx =0x40
[ 14.388723@3] fb: osd[0] canvas.addr=0x79300000
[ 14.388726@3] fb: osd[0] canvas.width=3840
[ 14.388727@3] fb: osd[0] canvas.height=1440
[ 14.388729@3] fb: osd[0] frame.width=1280
[ 14.388730@3] fb: osd[0] frame.height=720
[ 14.448232@3] fb: use ion buffer for fb memory
[ 14.448297@3] meson-fb meson-fb.16: create ion_client ffffffc065398540, handle=ffffffc052d5cb40
[ 14.448303@3] meson-fb meson-fb.16: ion memory(1): created fb at 0x000000007ab51000, size 1 MiB
[ 14.448309@3] fb: Frame buffer memory assigned at
[ 14.448309@3] fb: 1, phy: 0x000000007ab51000, vir:0xffffff8003be8000, size=1024K
[ 14.448309@3]
[ 14.448311@3] fb: fb1 open, logo index:1
[ 14.487048@3] fb: osd[1] canvas.idx =0x43
[ 14.487051@3] fb: osd[1] canvas.addr=0x7ab51000
[ 14.487054@3] fb: osd[1] canvas.width=128
[ 14.487055@3] fb: osd[1] canvas.height=32
[ 14.487056@3] fb: osd[1] frame.width=32
[ 14.487058@3] fb: osd[1] frame.height=32
[ 14.520537@4] vout_serve: vmode set to 720p60hz
[ 14.520537@4]
[ 14.528492@4] vout_serve: don't set the same mode as current
[ 14.534292@4] fb: osd0 free scale DISABLE
[ 14.550604@4] fb: osd[0] enable: 1 (amlogics905x_in)
[ 15.059914@0] dhd_open: Enter ffffffc052f22000
[ 15.063579@0]
[ 15.063579@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 15.063579@0] Compiled in drivers/net/wireless/bcmdhd
[ 15.081515@0] wl_android_wifi_on in 1
[ 15.085310@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 15.089800@0] wifi_platform_set_power = 1
[ 15.093712@0] ======== PULL WL_REG_ON HIGH! ========
[ 15.098736@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 15.305569@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 15.818577@0] sdio_reset_comm():
[ 15.850200@5] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 15.957697@7] sdio: clk 200000000 SDR mode tuning start
[ 15.962285@7] sdio: rx_tuning_result[0] = 10
[ 15.966856@7] sdio: rx_tuning_result[1] = 10
[ 15.971405@7] sdio: rx_tuning_result[2] = 10
[ 15.975941@7] sdio: rx_tuning_result[3] = 10
[ 15.980253@0] sdio: best_win_start =0, best_win_size =4
[ 15.984003@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 15.991338@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 15.997524@0] sdioh_start: set sd_f2_blocksize 128
[ 16.002670@0]
[ 16.002670@0]
[ 16.002670@0] dhd_bus_devreset: == WLAN ON ==
[ 16.015371@0] F1 signature read @0x18000000=0x15264345
[ 16.024185@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 16.029489@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 16.036154@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 16.041125@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 16.049063@0] dhd_conf_read_config: PM = 0
[ 16.052988@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 16.061753@0] dhdsdio_download_firmware: set use_rxchain 0
[ 16.067172@0] dhdsdio_download_firmware: set txglomsize 40
[ 16.072599@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 16.078102@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 16.084346@0] Final nv_path=/lib/firmware/brcm/
[ 16.088821@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 16.153854@0] dhdsdio_download_nvram: error reading nvram file: -21
[ 16.158440@0] _dhdsdio_download_firmware: dongle nvram file download failed
[ 16.165429@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 16.170703@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 16.176720@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 16.182171@0] wifi_platform_set_power = 0
[ 16.186035@0] ======== PULL WL_REG_ON LOW! ========
[ 16.190885@0] wl_android_wifi_on: Failed
[ 16.194748@0] dhd_open : wl_android_wifi_on failed (-35)
[ 16.200046@0] dhd_stop: Enter ffffffc052f22000
[ 16.204407@0] wl_android_wifi_off in 1
[ 16.208212@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 16.212962@0] wl_android_wifi_off out
[ 16.216758@0] dhd_stop: Exit
[ 16.220502@0] dhd_open: Exit ret=-1
[ 16.355280@6] dhd_open: Enter ffffffc052f22000
[ 16.360059@6]
[ 16.360059@6] Dongle Host Driver, version 1.201.59.6 (r5063[ 16.381514@6] wl_android_wifi_on in 1
[ 16.381611@4] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 1[ 16.398528@0] wifi_platform_set_power = 1
[ 16.398685@4] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 16.409701@0] ======== PULL WL_REG_ON HIGH! ========
[ 16.414595@0] aml_wifi wifi.33: [extern_wifi_set_ena[ 16.424878@4] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 16.448755@4] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 16.621636@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 16.718844@4] libphy: stmmac-0:00 - Link is Up - 100/Full
[ 17.128589@1] sdio_reset_comm():
[ 17.161310@7] sdio_read_cis: 3 callbacks suppressed
[ 17.166713@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 17.174788@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 17.182818@0] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 17.191948@0] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 17.289878@4] sdio: clk 200000000 SDR mode tuning start
[ 17.295187@4] sdio: rx_tuning_result[0] = 10
[ 17.300466@4] sdio: rx_tuning_result[1] = 10
[ 17.305616@4] sdio: rx_tuning_result[2] = 10
[ 17.310754@1] sdio: rx_tuning_result[3] = 10
[ 17.314738@1] sdio: best_win_start =0, best_win_size =4
[ 17.318725@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 17.325830@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 17.332045@1] sdioh_start: set sd_f2_blocksize 128
[ 17.337095@1]
[ 17.337095@1]
[ 17.337095@1] dhd_bus_devreset: == WLAN ON ==
[ 17.351272@1] F1 signature read @0x18000000=0x15264345
[ 17.359826@1] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 17.365663@1] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 17.372386@1] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 17.377354@1] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 17.385288@1] dhd_conf_read_config: PM = 0
[ 17.389599@1] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 17.397968@1] dhdsdio_download_firmware: set use_rxchain 0
[ 17.403413@1] dhdsdio_download_firmware: set txglomsize 40
[ 17.408848@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 17.414353@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 17.420589@1] Final nv_path=/lib/firmware/brcm/
[ 17.425049@1] Final conf_path=/lib/firmware/brcm/config.txt
Debian GNU/Linux 8 amlogic-s905x ttyS0
amlogic-s905x login: [ 17.485005@1] dhdsdio_download_nvram: error reading nvram file: -21
[ 17.491124@1] _dhdsdio_download_firmware: dongle nvram file download failed
[ 17.498041@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 17.503362@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 17.509408@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 17.514787@1] wifi_platform_set_power = 0
[ 17.518932@1] ======== PULL WL_REG_ON LOW! ========
[ 17.523521@1] wl_android_wifi_on: Failed
[ 17.527485@1] dhd_open : wl_android_wifi_on failed (-35)
[ 17.532678@1] dhd_stop: Enter ffffffc052f22000
[ 17.537062@1] wl_android_wifi_off in 1
[ 17.540884@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 17.545600@1] wl_android_wifi_off out
[ 17.549708@1] dhd_stop: Exit
[ 17.553775@1] dhd_open: Exit ret=-1
[ 17.558518@1] dhd_open: Enter ffffffc052f22000
[ 17.562067@1]
[ 17.562067@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 17.562067@1] Compiled in drivers/net/wireless/bcmdhd
[ 17.579586@1] wl_android_wifi_on in 1
[ 17.583198@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 17.587906@1] wifi_platform_set_power = 1
[ 17.591896@1] ======== PULL WL_REG_ON HIGH! ========
[ 17.596810@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 17.803722@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 18.318572@1] sdio_reset_comm():
[ 18.350503@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 18.357696@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 18.364774@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 18.373879@7] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 18.471692@7] sdio: clk 200000000 SDR mode tuning start
[ 18.476365@7] sdio: rx_tuning_result[0] = 10
[ 18.481013@7] sdio: rx_tuning_result[1] = 10
[ 18.485543@7] sdio: rx_tuning_result[2] = 10
[ 18.489972@7] sdio: rx_tuning_result[3] = 10
[ 18.494041@2] sdio: best_win_start =0, best_win_size =4
[ 18.497784@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 18.505146@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 18.511322@2] sdioh_start: set sd_f2_blocksize 128
[ 18.516382@2]
[ 18.516382@2]
[ 18.516382@2] dhd_bus_devreset: == WLAN ON ==
[ 18.528076@2] F1 signature read @0x18000000=0x15264345
[ 18.536739@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 18.541707@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 18.548352@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 18.553362@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 18.561277@2] dhd_conf_read_config: PM = 0
[ 18.565232@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 18.573979@2] dhdsdio_download_firmware: set use_rxchain 0
[ 18.579406@2] dhdsdio_download_firmware: set txglomsize 40
[ 18.584827@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 18.590382@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 18.596556@2] Final nv_path=/lib/firmware/brcm/
[ 18.601054@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 18.661794@2] dhdsdio_download_nvram: error reading nvram file: -21
[ 18.665856@2] _dhdsdio_download_firmware: dongle nvram file download failed
[ 18.672821@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 18.678101@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 18.684150@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 18.689560@2] wifi_platform_set_power = 0
[ 18.693449@2] ======== PULL WL_REG_ON LOW! ========
[ 18.698279@2] wl_android_wifi_on: Failed
[ 18.702175@2] dhd_open : wl_android_wifi_on failed (-35)
[ 18.707425@2] dhd_stop: Enter ffffffc052f22000
[ 18.711833@2] wl_android_wifi_off in 1
[ 18.715530@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 18.720371@2] wl_android_wifi_off out
[ 18.723982@2] dhd_stop: Exit
[ 18.727501@2] dhd_open: Exit ret=-1
[ 18.739298@2] dhd_open: Enter ffffffc052f22000
[ 18.742799@2]
[ 18.742799@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 18.742799@2] Compiled in drivers/net/wireless/bcmdhd
[ 18.760246@2] wl_android_wifi_on in 1
[ 18.763863@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 18.768602@2] wifi_platform_set_power = 1
[ 18.772550@2] ======== PULL WL_REG_ON HIGH! ========
[ 18.777484@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 18.984407@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 19.498576@2] sdio_reset_comm():
[ 19.530521@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 19.537687@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 19.642715@4] sdio: clk 200000000 SDR mode tuning start
[ 19.647455@4] sdio: rx_tuning_result[0] = 10
[ 19.652221@4] sdio: rx_tuning_result[1] = 10
[ 19.656970@4] sdio: rx_tuning_result[2] = 10
[ 19.661601@4] sdio: rx_tuning_result[3] = 10
[ 19.665934@3] sdio: best_win_start =0, best_win_size =4
[ 19.669710@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 19.677004@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 19.683217@3] sdioh_start: set sd_f2_blocksize 128
[ 19.688275@3]
[ 19.688275@3]
[ 19.688275@3] dhd_bus_devreset: == WLAN ON ==
[ 19.700391@3] F1 signature read @0x18000000=0x15264345
[ 19.708872@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 19.713882@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 19.720594@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 19.725579@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 19.733527@3] dhd_conf_read_config: PM = 0
[ 19.737464@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 19.746220@3] dhdsdio_download_firmware: set use_rxchain 0
[ 19.751651@3] dhdsdio_download_firmware: set txglomsize 40
[ 19.757059@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 19.762603@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 19.768813@3] Final nv_path=/lib/firmware/brcm/
[ 19.773273@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 19.831641@3] dhdsdio_download_nvram: error reading nvram file: -21
[ 19.835779@3] _dhdsdio_download_firmware: dongle nvram file download failed
[ 19.842742@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 19.848022@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 19.854084@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 19.859492@3] wifi_platform_set_power = 0
[ 19.863370@3] ======== PULL WL_REG_ON LOW! ========
[ 19.868200@3] wl_android_wifi_on: Failed
[ 19.872109@3] dhd_open : wl_android_wifi_on failed (-35)
[ 19.877346@3] dhd_stop: Enter ffffffc052f22000
[ 19.881768@3] wl_android_wifi_off in 1
[ 19.885500@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 19.890304@3] wl_android_wifi_off out
[ 19.893999@3] dhd_stop: Exit
[ 19.897647@3] dhd_open: Exit ret=-1
[ 19.901845@3] dhd_open: Enter ffffffc052f22000
[ 19.905520@3]
[ 19.905520@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 19.905520@3] Compiled in drivers/net/wireless/bcmdhd
[ 19.923074@3] wl_android_wifi_on in 1
[ 19.926687@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 19.931411@3] wifi_platform_set_power = 1
[ 19.935347@3] ======== PULL WL_REG_ON HIGH! ========
[ 19.940318@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 20.147198@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 20.658574@2] sdio_reset_comm():
[ 20.793874@5] sdio: clk 200000000 SDR mode tuning start
[ 20.798884@7] sdio: rx_tuning_result[0] = 10
[ 20.803609@7] sdio: rx_tuning_result[1] = 10
[ 20.808237@7] sdio: rx_tuning_result[2] = 10
[ 20.813167@7] sdio: rx_tuning_result[3] = 10
[ 20.817571@3] sdio: best_win_start =0, best_win_size =4
[ 20.821356@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 20.828677@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 20.834840@3] sdioh_start: set sd_f2_blocksize 128
[ 20.839944@3]
[ 20.839944@3]
[ 20.839944@3] dhd_bus_devreset: == WLAN ON ==
[ 20.852490@3] F1 signature read @0x18000000=0x15264345
[ 20.860968@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 20.866074@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 20.872796@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 20.877767@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 20.885713@3] dhd_conf_read_config: PM = 0
[ 20.889681@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 20.898381@3] dhdsdio_download_firmware: set use_rxchain 0
[ 20.903838@3] dhdsdio_download_firmware: set txglomsize 40
[ 20.909273@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 20.914766@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 20.921006@3] Final nv_path=/lib/firmware/brcm/
[ 20.925461@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 20.983991@3] dhdsdio_download_nvram: error reading nvram file: -21
[ 20.988190@3] _dhdsdio_download_firmware: dongle nvram file download failed
[ 20.995151@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 21.000459@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 21.006469@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 21.011899@3] wifi_platform_set_power = 0
[ 21.015783@3] ======== PULL WL_REG_ON LOW! ========
[ 21.020642@3] wl_android_wifi_on: Failed
[ 21.024496@3] dhd_open : wl_android_wifi_on failed (-35)
[ 21.029782@3] dhd_stop: Enter ffffffc052f22000
[ 21.034155@3] wl_android_wifi_off in 1
[ 21.037936@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 21.042718@3] wl_android_wifi_off out
[ 21.046423@3] dhd_stop: Exit
[ 21.050146@3] dhd_open: Exit ret=-1
[ 21.057146@3] dhd_open: Enter ffffffc052f22000
[ 21.060971@3]
[ 21.060971@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 21.060971@3] Compiled in drivers/net/wireless/bcmdhd
[ 21.078665@3] wl_android_wifi_on in 1
[ 21.082848@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 21.087031@3] wifi_platform_set_power = 1
[ 21.091295@3] ======== PULL WL_REG_ON HIGH! ========
[ 21.095886@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 21.302815@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 21.808583@3] sdio_reset_comm():
[ 21.943708@4] sdio: clk 200000000 SDR mode tuning start
[ 21.949263@4] sdio: rx_tuning_result[0] = 10
[ 21.953988@4] sdio: rx_tuning_result[1] = 10
[ 21.958667@7] sdio: rx_tuning_result[2] = 10
[ 21.964042@7] sdio: rx_tuning_result[3] = 10
[ 21.968447@2] sdio: best_win_start =0, best_win_size =4
[ 21.972222@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 21.979545@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 21.985728@2] sdioh_start: set sd_f2_blocksize 128
[ 21.990845@2]
[ 21.990845@2]
[ 21.990845@2] dhd_bus_devreset: == WLAN ON ==
[ 22.003403@2] F1 signature read @0x18000000=0x15264345
[ 22.012023@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 22.017129@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 22.023854@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 22.028847@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 22.036741@2] dhd_conf_read_config: PM = 0
[ 22.040725@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 22.049464@2] dhdsdio_download_firmware: set use_rxchain 0
[ 22.054871@2] dhdsdio_download_firmware: set txglomsize 40
[ 22.060318@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 22.065825@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 22.072047@2] Final nv_path=/lib/firmware/brcm/
[ 22.076520@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 22.137309@2] dhdsdio_download_nvram: error reading nvram file: -21
[ 22.141539@2] _dhdsdio_download_firmware: dongle nvram file download failed
[ 22.148451@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 22.153780@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 22.159808@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 22.165204@2] wifi_platform_set_power = 0
[ 22.169122@2] ======== PULL WL_REG_ON LOW! ========
[ 22.173939@2] wl_android_wifi_on: Failed
[ 22.177821@2] dhd_open : wl_android_wifi_on failed (-35)
[ 22.183097@2] dhd_stop: Enter ffffffc052f22000
[ 22.187481@2] wl_android_wifi_off in 1
[ 22.191308@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 22.196019@2] wl_android_wifi_off out
[ 22.199743@2] dhd_stop: Exit
[ 22.203459@2] dhd_open: Exit ret=-1
[ 22.207784@2] dhd_open: Enter ffffffc052f22000
[ 22.211587@2]
[ 22.211587@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 22.211587@2] Compiled in drivers/net/wireless/bcmdhd
[ 22.229400@2] wl_android_wifi_on in 1
[ 22.233059@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 22.237730@2] wifi_platform_set_power = 1
[ 22.241723@2] ======== PULL WL_REG_ON HIGH! ========
[ 22.246643@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 22.453652@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 22.968575@2] sdio_reset_comm():
[ 23.000521@5] sdio_read_cis: 10 callbacks suppressed
[ 23.005061@5] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 23.012619@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 23.019706@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 23.028952@2] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 23.126623@7] sdio: clk 200000000 SDR mode tuning start
[ 23.131580@7] sdio: rx_tuning_result[0] = 10
[ 23.136224@7] sdio: rx_tuning_result[1] = 10
[ 23.140756@4] sdio: rx_tuning_result[2] = 10
[ 23.145217@1] sdio: rx_tuning_result[3] = 10
[ 23.148650@1] sdio: best_win_start =0, best_win_size =4
[ 23.152906@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 23.160277@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 23.166431@1] sdioh_start: set sd_f2_blocksize 128
[ 23.171551@1]
[ 23.171551@1]
[ 23.171551@1] dhd_bus_devreset: == WLAN ON ==
[ 23.183257@1] F1 signature read @0x18000000=0x15264345
[ 23.191963@1] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 23.196867@1] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 23.203593@1] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 23.208552@1] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 23.216483@1] dhd_conf_read_config: PM = 0
[ 23.220471@1] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 23.229180@1] dhdsdio_download_firmware: set use_rxchain 0
[ 23.234598@1] dhdsdio_download_firmware: set txglomsize 40
[ 23.240046@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 23.245553@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 23.251792@1] Final nv_path=/lib/firmware/brcm/
[ 23.256247@1] Final conf_path=/lib/firmware/brcm/config.txt
[ 23.316887@1] dhdsdio_download_nvram: error reading nvram file: -21
[ 23.321023@1] _dhdsdio_download_firmware: dongle nvram file download failed
[ 23.327935@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 23.333264@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 23.339314@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 23.344686@1] wifi_platform_set_power = 0
[ 23.348608@1] ======== PULL WL_REG_ON LOW! ========
[ 23.353426@1] wl_android_wifi_on: Failed
[ 23.357307@1] dhd_open : wl_android_wifi_on failed (-35)
[ 23.362583@1] dhd_stop: Enter ffffffc052f22000
[ 23.366967@1] wl_android_wifi_off in 1
[ 23.370704@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 23.375505@1] wl_android_wifi_off out
[ 23.379140@1] dhd_stop: Exit
[ 23.382646@1] dhd_open: Exit ret=-1
[ 23.390089@1] dhd_open: Enter ffffffc052f22000
[ 23.393609@1]
[ 23.393609@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 23.393609@1] Compiled in drivers/net/wireless/bcmdhd
[ 23.411137@1] wl_android_wifi_on in 1
[ 23.414766@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 23.419462@1] wifi_platform_set_power = 1
[ 23.423409@1] ======== PULL WL_REG_ON HIGH! ========
[ 23.428344@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 23.635285@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 24.148573@1] sdio_reset_comm():
[ 24.181149@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 24.188316@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 24.195406@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 24.204528@4] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 24.302540@4] sdio: clk 200000000 SDR mode tuning start
[ 24.307217@4] sdio: rx_tuning_result[0] = 10
[ 24.311866@4] sdio: rx_tuning_result[1] = 10
[ 24.316415@4] sdio: rx_tuning_result[2] = 10
[ 24.321084@4] sdio: rx_tuning_result[3] = 10
[ 24.325166@2] sdio: best_win_start =0, best_win_size =4
[ 24.328941@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 24.336247@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 24.342452@2] sdioh_start: set sd_f2_blocksize 128
[ 24.347518@2]
[ 24.347518@2]
[ 24.347518@2] dhd_bus_devreset: == WLAN ON ==
[ 24.359244@2] F1 signature read @0x18000000=0x15264345
[ 24.367729@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 24.372708@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 24.379360@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 24.384338@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 24.392293@2] dhd_conf_read_config: PM = 0
[ 24.396226@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 24.404966@2] dhdsdio_download_firmware: set use_rxchain 0
[ 24.410397@2] dhdsdio_download_firmware: set txglomsize 40
[ 24.415819@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 24.421349@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 24.427548@2] Final nv_path=/lib/firmware/brcm/
[ 24.432045@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 24.493378@2] dhdsdio_download_nvram: error reading nvram file: -21
[ 24.497446@2] _dhdsdio_download_firmware: dongle nvram file download failed
[ 24.504408@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 24.509703@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 24.515723@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 24.521153@2] wifi_platform_set_power = 0
[ 24.525037@2] ======== PULL WL_REG_ON LOW! ========
[ 24.529881@2] wl_android_wifi_on: Failed
[ 24.533749@2] dhd_open : wl_android_wifi_on failed (-35)
[ 24.539023@2] dhd_stop: Enter ffffffc052f22000
[ 24.543408@2] wl_android_wifi_off in 1
[ 24.547116@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 24.551958@2] wl_android_wifi_off out
[ 24.555569@2] dhd_stop: Exit
[ 24.559116@2] dhd_open: Exit ret=-1
[ 24.563186@2] dhd_open: Enter ffffffc052f22000
[ 24.566685@2]
[ 24.566685@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 24.566685@2] Compiled in drivers/net/wireless/bcmdhd
[ 24.584136@2] wl_android_wifi_on in 1
[ 24.587751@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 24.592513@2] wifi_platform_set_power = 1
[ 24.596444@2] ======== PULL WL_REG_ON HIGH! ========
[ 24.601399@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 24.808284@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 25.318573@2] sdio_reset_comm():
[ 25.350597@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 25.357772@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 25.463141@7] sdio: clk 200000000 SDR mode tuning start
[ 25.467832@7] sdio: rx_tuning_result[0] = 10
[ 25.472586@7] sdio: rx_tuning_result[1] = 10
[ 25.477299@7] sdio: rx_tuning_result[2] = 10
[ 25.481934@7] sdio: rx_tuning_result[3] = 10
[ 25.486267@1] sdio: best_win_start =0, best_win_size =4
[ 25.490034@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 25.497344@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 25.503544@1] sdioh_start: set sd_f2_blocksize 128
[ 25.508647@1]
[ 25.508647@1]
[ 25.508647@1] dhd_bus_devreset: == WLAN ON ==
[ 25.522298@1] F1 signature read @0x18000000=0x15264345
[ 25.530829@1] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 25.535854@1] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 25.542576@1] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 25.547540@1] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 25.555472@1] dhd_conf_read_config: PM = 0
[ 25.559441@1] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 25.568154@1] dhdsdio_download_firmware: set use_rxchain 0
[ 25.573618@1] dhdsdio_download_firmware: set txglomsize 40
[ 25.579034@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 25.584540@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 25.590762@1] Final nv_path=/lib/firmware/brcm/
[ 25.595235@1] Final conf_path=/lib/firmware/brcm/config.txt
[ 25.655884@1] dhdsdio_download_nvram: error reading nvram file: -21
[ 25.660070@1] _dhdsdio_download_firmware: dongle nvram file download failed
[ 25.666964@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 25.672288@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 25.678304@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 25.683725@1] wifi_platform_set_power = 0
[ 25.687618@1] ======== PULL WL_REG_ON LOW! ========
[ 25.692475@1] wl_android_wifi_on: Failed
[ 25.696330@1] dhd_open : wl_android_wifi_on failed (-35)
[ 25.701606@1] dhd_stop: Enter ffffffc052f22000
[ 25.705989@1] wl_android_wifi_off in 1
[ 25.709740@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 25.714527@1] wl_android_wifi_off out
[ 25.718230@1] dhd_stop: Exit
[ 25.721914@1] dhd_open: Exit ret=-1
[ 25.730514@1] dhd_open: Enter ffffffc052f22000
[ 25.734199@1]
[ 25.734199@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 25.734199@1] Compiled in drivers/net/wireless/bcmdhd
[ 25.751787@1] wl_android_wifi_on in 1
[ 25.755409@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 25.760105@1] wifi_platform_set_power = 1
[ 25.764053@1] ======== PULL WL_REG_ON HIGH! ========
[ 25.769012@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 25.975889@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 26.488568@1] sdio_reset_comm():
[ 26.623759@4] sdio: clk 200000000 SDR mode tuning start
[ 26.628580@7] sdio: rx_tuning_result[0] = 10
[ 26.633343@7] sdio: rx_tuning_result[1] = 10
[ 26.637996@7] sdio: rx_tuning_result[2] = 10
[ 26.642704@7] sdio: rx_tuning_result[3] = 10
[ 26.647141@3] sdio: best_win_start =0, best_win_size =4
[ 26.650930@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 26.658219@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 26.664437@3] sdioh_start: set sd_f2_blocksize 128
[ 26.669520@3]
[ 26.669520@3]
[ 26.669520@3] dhd_bus_devreset: == WLAN ON ==
[ 26.682110@3] F1 signature read @0x18000000=0x15264345
[ 26.690593@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 26.695708@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 26.702430@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 26.707405@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 26.715348@3] dhd_conf_read_config: PM = 0
[ 26.719318@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 26.728019@3] dhdsdio_download_firmware: set use_rxchain 0
[ 26.733476@3] dhdsdio_download_firmware: set txglomsize 40
[ 26.738910@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 26.744403@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 26.750641@3] Final nv_path=/lib/firmware/brcm/
[ 26.755099@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 26.813394@3] dhdsdio_download_nvram: error reading nvram file: -21
[ 26.817594@3] _dhdsdio_download_firmware: dongle nvram file download failed
[ 26.824556@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 26.829865@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 26.835874@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 26.841304@3] wifi_platform_set_power = 0
[ 26.845187@3] ======== PULL WL_REG_ON LOW! ========
[ 26.850046@3] wl_android_wifi_on: Failed
[ 26.853900@3] dhd_open : wl_android_wifi_on failed (-35)
[ 26.859186@3] dhd_stop: Enter ffffffc052f22000
[ 26.863559@3] wl_android_wifi_off in 1
[ 26.867341@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 26.872122@3] wl_android_wifi_off out
[ 26.875831@3] dhd_stop: Exit
[ 26.879557@3] dhd_open: Exit ret=-1
[ 26.883839@3] dhd_open: Enter ffffffc052f22000
[ 26.887559@3]
[ 26.887559@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 26.887559@3] Compiled in drivers/net/wireless/bcmdhd
[ 26.905277@3] wl_android_wifi_on in 1
[ 26.909499@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 26.913576@3] wifi_platform_set_power = 1
[ 26.917542@3] ======== PULL WL_REG_ON HIGH! ========
[ 26.922511@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 27.129407@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 27.638581@0] sdio_reset_comm():
[ 27.774114@4] sdio: clk 200000000 SDR mode tuning start
[ 27.778998@5] sdio: rx_tuning_result[0] = 10
[ 27.783748@5] sdio: rx_tuning_result[1] = 10
[ 27.788385@5] sdio: rx_tuning_result[2] = 10
[ 27.793066@5] sdio: rx_tuning_result[3] = 10
[ 27.797493@2] sdio: best_win_start =0, best_win_size =4
[ 27.801254@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 27.808580@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 27.814756@2] sdioh_start: set sd_f2_blocksize 128
[ 27.819858@2]
[ 27.819858@2]
[ 27.819858@2] dhd_bus_devreset: == WLAN ON ==
[ 27.832414@2] F1 signature read @0x18000000=0x15264345
[ 27.841081@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 27.846228@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 27.852950@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 27.857911@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 27.865843@2] dhd_conf_read_config: PM = 0
[ 27.869811@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 27.878524@2] dhdsdio_download_firmware: set use_rxchain 0
[ 27.883969@2] dhdsdio_download_firmware: set txglomsize 40
[ 27.889404@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 27.894910@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 27.901132@2] Final nv_path=/lib/firmware/brcm/
[ 27.905605@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 27.966423@2] dhdsdio_download_nvram: error reading nvram file: -21
[ 27.970653@2] _dhdsdio_download_firmware: dongle nvram file download failed
[ 27.977561@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 27.982889@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 27.988943@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 27.994311@2] wifi_platform_set_power = 0
[ 27.998220@2] ======== PULL WL_REG_ON LOW! ========
[ 28.003076@2] wl_android_wifi_on: Failed
[ 28.006933@2] dhd_open : wl_android_wifi_on failed (-35)
[ 28.012209@2] dhd_stop: Enter ffffffc052f22000
[ 28.016662@2] wl_android_wifi_off in 1
[ 28.021106@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 28.025130@2] wl_android_wifi_off out
[ 28.028859@2] dhd_stop: Exit
[ 28.032583@2] dhd_open: Exit ret=-1
[ 28.039373@2] dhd_open: Enter ffffffc052f22000
[ 28.043113@2]
[ 28.043113@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 28.043113@2] Compiled in drivers/net/wireless/bcmdhd
[ 28.060844@2] wl_android_wifi_on in 1
[ 28.064471@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 28.069178@2] wifi_platform_set_power = 1
[ 28.073129@2] ======== PULL WL_REG_ON HIGH! ========
[ 28.078063@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 28.284992@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 28.798569@2] sdio_reset_comm():
[ 28.830503@4] sdio_read_cis: 10 callbacks suppressed
[ 28.835033@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 28.842602@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 28.849690@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 28.858959@0] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 28.956554@5] sdio: clk 200000000 SDR mode tuning start
[ 28.961260@5] sdio: rx_tuning_result[0] = 10
[ 28.965888@5] sdio: rx_tuning_result[1] = 10
[ 28.970387@5] sdio: rx_tuning_result[2] = 10
[ 28.974766@5] sdio: rx_tuning_result[3] = 10
[ 28.978843@1] sdio: best_win_start =0, best_win_size =4
[ 28.982611@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 28.989978@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 28.996137@1] sdioh_start: set sd_f2_blocksize 128
[ 29.001234@1]
[ 29.001234@1]
[ 29.001234@1] dhd_bus_devreset: == WLAN ON ==
[ 29.012920@1] F1 signature read @0x18000000=0x15264345
[ 29.021540@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 29.026418@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 29.033168@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 29.038121@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 29.046053@2] dhd_conf_read_config: PM = 0
[ 29.050022@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 29.058748@2] dhdsdio_download_firmware: set use_rxchain 0
[ 29.064167@2] dhdsdio_download_firmware: set txglomsize 40
[ 29.069614@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 29.075121@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 29.081343@2] Final nv_path=/lib/firmware/brcm/
[ 29.085816@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 29.146654@2] dhdsdio_download_nvram: error reading nvram file: -21
[ 29.150781@2] _dhdsdio_download_firmware: dongle nvram file download failed
[ 29.157698@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 29.163023@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 29.169053@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 29.174452@2] wifi_platform_set_power = 0
[ 29.178353@2] ======== PULL WL_REG_ON LOW! ========
[ 29.183197@2] wl_android_wifi_on: Failed
[ 29.187066@2] dhd_open : wl_android_wifi_on failed (-35)
[ 29.192362@2] dhd_stop: Enter ffffffc052f22000
[ 29.196725@2] wl_android_wifi_off in 1
[ 29.200446@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 29.205263@2] wl_android_wifi_off out
[ 29.208897@2] dhd_stop: Exit
[ 29.212395@2] dhd_open: Exit ret=-1
[ 29.216470@2] dhd_open: Enter ffffffc052f22000
[ 29.220004@2]
[ 29.220004@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 29.220004@2] Compiled in drivers/net/wireless/bcmdhd
[ 29.237496@2] wl_android_wifi_on in 1
[ 29.241137@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 29.245845@2] wifi_platform_set_power = 1
[ 29.249837@2] ======== PULL WL_REG_ON HIGH! ========
[ 29.254748@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 29.461660@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 29.968577@2] sdio_reset_comm():
[ 30.000527@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 30.007704@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 30.014805@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 30.023933@7] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 30.121649@4] sdio: clk 200000000 SDR mode tuning start
[ 30.126338@4] sdio: rx_tuning_result[0] = 10
[ 30.130987@4] sdio: rx_tuning_result[1] = 10
[ 30.135544@4] sdio: rx_tuning_result[2] = 10
[ 30.139975@4] sdio: rx_tuning_result[3] = 10
[ 30.144063@3] sdio: best_win_start =0, best_win_size =4
[ 30.147805@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 30.155181@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 30.161349@3] sdioh_start: set sd_f2_blocksize 128
[ 30.166407@3]
[ 30.166407@3]
[ 30.166407@3] dhd_bus_devreset: == WLAN ON ==
[ 30.178124@3] F1 signature read @0x18000000=0x15264345
[ 30.186609@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 30.191555@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 30.198231@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 30.203265@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 30.211176@3] dhd_conf_read_config: PM = 0
[ 30.215115@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 30.223871@3] dhdsdio_download_firmware: set use_rxchain 0
[ 30.229304@3] dhdsdio_download_firmware: set txglomsize 40
[ 30.234709@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 30.240255@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 30.246439@3] Final nv_path=/lib/firmware/brcm/
[ 30.250949@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 30.313414@0] dhdsdio_download_nvram: error reading nvram file: -21
[ 30.318052@0] _dhdsdio_download_firmware: dongle nvram file download failed
[ 30.324977@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 30.330278@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 30.336323@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 30.341727@0] wifi_platform_set_power = 0
[ 30.345941@0] ======== PULL WL_REG_ON LOW! ========
[ 30.350478@0] wl_android_wifi_on: Failed
[ 30.354713@0] dhd_open : wl_android_wifi_on failed (-35)
[ 30.359604@0] dhd_stop: Enter ffffffc052f22000
[ 30.363983@0] wl_android_wifi_off in 1
[ 30.367712@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 30.372541@0] wl_android_wifi_off out
[ 30.376678@0] dhd_stop: Exit
[ 30.380821@0] dhd_open: Exit ret=-1
[ 30.387901@0] dhd_open: Enter ffffffc052f22000
[ 30.391466@0]
[ 30.391466@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 30.391466@0] Compiled in drivers/net/wireless/bcmdhd
[ 30.409022@0] wl_android_wifi_on in 1
[ 30.412647@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 30.417341@0] wifi_platform_set_power = 1
[ 30.421304@0] ======== PULL WL_REG_ON HIGH! ========
[ 30.426222@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 30.633176@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 31.138580@1] sdio_reset_comm():
[ 31.170534@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 31.178407@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 31.283533@4] sdio: clk 200000000 SDR mode tuning start
[ 31.288260@4] sdio: rx_tuning_result[0] = 10
[ 31.293037@4] sdio: rx_tuning_result[1] = 10
[ 31.297778@4] sdio: rx_tuning_result[2] = 10
[ 31.302432@4] sdio: rx_tuning_result[3] = 10
[ 31.306785@0] sdio: best_win_start =0, best_win_size =4
[ 31.310552@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 31.317882@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 31.324088@0] sdioh_start: set sd_f2_blocksize 128
[ 31.329210@0]
[ 31.329210@0]
[ 31.329210@0] dhd_bus_devreset: == WLAN ON ==
[ 31.341406@0] F1 signature read @0x18000000=0x15264345
[ 31.350057@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 31.355115@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 31.361826@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 31.366820@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 31.374722@0] dhd_conf_read_config: PM = 0
[ 31.378686@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 31.387425@0] dhdsdio_download_firmware: set use_rxchain 0
[ 31.392851@0] dhdsdio_download_firmware: set txglomsize 40
[ 31.398267@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 31.403830@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 31.410011@0] Final nv_path=/lib/firmware/brcm/
[ 31.414481@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 31.477273@0] dhdsdio_download_nvram: error reading nvram file: -21
[ 31.481449@0] _dhdsdio_download_firmware: dongle nvram file download failed
[ 31.488412@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 31.493689@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 31.499745@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 31.505122@0] wifi_platform_set_power = 0
[ 31.509038@0] ======== PULL WL_REG_ON LOW! ========
[ 31.513851@0] wl_android_wifi_on: Failed
[ 31.517756@0] dhd_open : wl_android_wifi_on failed (-35)
[ 31.523013@0] dhd_stop: Enter ffffffc052f22000
[ 31.527392@0] wl_android_wifi_off in 1
[ 31.531151@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 31.535951@0] wl_android_wifi_off out
[ 31.539673@0] dhd_stop: Exit
[ 31.543339@0] dhd_open: Exit ret=-1
[ 31.547540@0] dhd_open: Enter ffffffc052f22000
[ 31.551314@0]
[ 31.551314@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 31.551314@0] Compiled in drivers/net/wireless/bcmdhd
[ 31.568895@0] wl_android_wifi_on in 1
[ 31.572510@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 31.577218@0] wifi_platform_set_power = 1
[ 31.581209@0] ======== PULL WL_REG_ON HIGH! ========
[ 31.586152@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 31.793044@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 32.298578@0] sdio_reset_comm():
[ 32.434083@4] sdio: clk 200000000 SDR mode tuning start
[ 32.438944@4] sdio: rx_tuning_result[0] = 10
[ 32.443687@4] sdio: rx_tuning_result[1] = 10
[ 32.448328@4] sdio: rx_tuning_result[2] = 10
[ 32.453002@4] sdio: rx_tuning_result[3] = 10
[ 32.457421@2] sdio: best_win_start =0, best_win_size =4
[ 32.461185@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 32.468492@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 32.474695@2] sdioh_start: set sd_f2_blocksize 128
[ 32.479806@2]
[ 32.479806@2]
[ 32.479806@2] dhd_bus_devreset: == WLAN ON ==
[ 32.494064@2] F1 signature read @0x18000000=0x15264345
[ 32.502766@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 32.507895@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 32.514587@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 32.519592@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 32.527493@2] dhd_conf_read_config: PM = 0
[ 32.531476@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 32.540204@2] dhdsdio_download_firmware: set use_rxchain 0
[ 32.545622@2] dhdsdio_download_firmware: set txglomsize 40
[ 32.551069@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 32.556576@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 32.562798@2] Final nv_path=/lib/firmware/brcm/
[ 32.567270@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 32.627211@2] dhdsdio_download_nvram: error reading nvram file: -21
[ 32.631437@2] _dhdsdio_download_firmware: dongle nvram file download failed
[ 32.638359@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 32.643676@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 32.649719@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 32.655104@2] wifi_platform_set_power = 0
[ 32.659026@2] ======== PULL WL_REG_ON LOW! ========
[ 32.663837@2] wl_android_wifi_on: Failed
[ 32.667718@2] dhd_open : wl_android_wifi_on failed (-35)
[ 32.672996@2] dhd_stop: Enter ffffffc052f22000
[ 32.677378@2] wl_android_wifi_off in 1
[ 32.681182@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 32.685916@2] wl_android_wifi_off out
[ 32.689635@2] dhd_stop: Exit
[ 32.693342@2] dhd_open: Exit ret=-1
[ 32.700075@2] dhd_open: Enter ffffffc052f22000
[ 32.703818@2]
[ 32.703818@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 32.703818@2] Compiled in drivers/net/wireless/bcmdhd
[ 32.721529@2] wl_android_wifi_on in 1
[ 32.725166@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 32.729877@2] wifi_platform_set_power = 1
[ 32.733829@2] ======== PULL WL_REG_ON HIGH! ========
[ 32.738790@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 32.945662@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 33.458573@2] sdio_reset_comm():
[ 33.594122@4] sdio: clk 200000000 SDR mode tuning start
[ 33.598968@4] sdio: rx_tuning_result[0] = 10
[ 33.603694@4] sdio: rx_tuning_result[1] = 10
[ 33.608326@4] sdio: rx_tuning_result[2] = 10
[ 33.613010@4] sdio: rx_tuning_result[3] = 10
[ 33.617453@1] sdio: best_win_start =0, best_win_size =4
[ 33.621207@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 33.628511@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 33.634717@1] sdioh_start: set sd_f2_blocksize 128
[ 33.639833@1]
[ 33.639833@1]
[ 33.639833@1] dhd_bus_devreset: == WLAN ON ==
[ 33.652414@1] F1 signature read @0x18000000=0x15264345
[ 33.660876@1] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 33.666004@1] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 33.672727@1] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 33.677698@1] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 33.685631@1] dhd_conf_read_config: PM = 0
[ 33.689597@1] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 33.698312@1] dhdsdio_download_firmware: set use_rxchain 0
[ 33.703772@1] dhdsdio_download_firmware: set txglomsize 40
[ 33.709192@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 33.714697@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 33.720920@1] Final nv_path=/lib/firmware/brcm/
[ 33.725393@1] Final conf_path=/lib/firmware/brcm/config.txt
[ 33.785458@1] dhdsdio_download_nvram: error reading nvram file: -21
[ 33.789705@1] _dhdsdio_download_firmware: dongle nvram file download failed
[ 33.796607@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 33.801927@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 33.807945@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 33.813363@1] wifi_platform_set_power = 0
[ 33.817258@1] ======== PULL WL_REG_ON LOW! ========
[ 33.822116@1] wl_android_wifi_on: Failed
[ 33.825971@1] dhd_open : wl_android_wifi_on failed (-35)
[ 33.831248@1] dhd_stop: Enter ffffffc052f22000
[ 33.835630@1] wl_android_wifi_off in 1
[ 33.839433@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 33.844167@1] wl_android_wifi_off out
[ 33.847871@1] dhd_stop: Exit
[ 33.851605@1] dhd_open: Exit ret=-1
[ 33.855895@1] dhd_open: Enter ffffffc052f22000
[ 33.859655@1]
[ 33.859655@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 33.859655@1] Compiled in drivers/net/wireless/bcmdhd
[ 33.877335@1] wl_android_wifi_on in 1
[ 33.880989@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 33.885672@1] wifi_platform_set_power = 1
[ 33.889653@1] ======== PULL WL_REG_ON HIGH! ========
[ 33.894575@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 34.101487@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 34.608565@1] sdio_reset_comm():
[ 34.640455@4] sdio_read_cis: 10 callbacks suppressed
[ 34.644975@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 34.652586@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 34.659691@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 34.668927@3] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 34.766266@5] sdio: clk 200000000 SDR mode tuning start
[ 34.770967@5] sdio: rx_tuning_result[0] = 10
[ 34.775572@5] sdio: rx_tuning_result[1] = 10
[ 34.780082@5] sdio: rx_tuning_result[2] = 10
[ 34.784432@5] sdio: rx_tuning_result[3] = 10
[ 34.788463@0] sdio: best_win_start =0, best_win_size =4
[ 34.792344@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 34.799680@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 34.805851@0] sdioh_start: set sd_f2_blocksize 128
[ 34.810991@0]
[ 34.810991@0]
[ 34.810991@0] dhd_bus_devreset: == WLAN ON ==
[ 34.822690@0] F1 signature read @0x18000000=0x15264345
[ 34.831358@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 34.836283@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 34.842981@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 34.847932@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 34.855893@0] dhd_conf_read_config: PM = 0
[ 34.859832@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 34.868587@0] dhdsdio_download_firmware: set use_rxchain 0
[ 34.873978@0] dhdsdio_download_firmware: set txglomsize 40
[ 34.879436@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 34.884953@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 34.891160@0] Final nv_path=/lib/firmware/brcm/
[ 34.895626@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 34.958317@0] dhdsdio_download_nvram: error reading nvram file: -21
[ 34.962448@0] _dhdsdio_download_firmware: dongle nvram file download failed
[ 34.969421@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 34.974669@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 34.980721@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 34.986144@0] wifi_platform_set_power = 0
[ 34.990038@0] ======== PULL WL_REG_ON LOW! ========
[ 34.994849@0] wl_android_wifi_on: Failed
[ 34.998767@0] dhd_open : wl_android_wifi_on failed (-35)
[ 35.003994@0] dhd_stop: Enter ffffffc052f22000
[ 35.008389@0] wl_android_wifi_off in 1
[ 35.012116@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 35.016949@0] wl_android_wifi_off out
[ 35.020569@0] dhd_stop: Exit
[ 35.024072@0] dhd_open: Exit ret=-1
[ 35.030624@0] dhd_open: Enter ffffffc052f22000
[ 35.034215@0]
[ 35.034215@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 35.034215@0] Compiled in drivers/net/wireless/bcmdhd
[ 35.051764@0] wl_android_wifi_on in 1
[ 35.055386@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 35.060101@0] wifi_platform_set_power = 1
[ 35.064031@0] ======== PULL WL_REG_ON HIGH! ========
[ 35.069016@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 35.275864@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 35.788576@0] sdio_reset_comm():
[ 35.820514@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 35.827692@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 35.834788@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 35.844638@7] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 35.942385@7] sdio: clk 200000000 SDR mode tuning start
[ 35.947084@7] sdio: rx_tuning_result[0] = 10
[ 35.951715@7] sdio: rx_tuning_result[1] = 10
[ 35.956267@7] sdio: rx_tuning_result[2] = 10
[ 35.960688@7] sdio: rx_tuning_result[3] = 10
[ 35.964772@2] sdio: best_win_start =0, best_win_size =4
[ 35.968515@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 35.975875@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 35.982053@2] sdioh_start: set sd_f2_blocksize 128
[ 35.987121@2]
[ 35.987121@2]
[ 35.987121@2] dhd_bus_devreset: == WLAN ON ==
[ 35.998880@2] F1 signature read @0x18000000=0x15264345
[ 36.007307@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 36.012293@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 36.018967@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 36.023948@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 36.031882@2] dhd_conf_read_config: PM = 0
[ 36.035835@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 36.044576@2] dhdsdio_download_firmware: set use_rxchain 0
[ 36.050018@2] dhdsdio_download_firmware: set txglomsize 40
[ 36.055429@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 36.060960@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 36.067158@2] Final nv_path=/lib/firmware/brcm/
[ 36.071655@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 36.132050@2] dhdsdio_download_nvram: error reading nvram file: -21
[ 36.136113@2] _dhdsdio_download_firmware: dongle nvram file download failed
[ 36.143063@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 36.148358@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 36.154407@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 36.159822@2] wifi_platform_set_power = 0
[ 36.163706@2] ======== PULL WL_REG_ON LOW! ========
[ 36.168536@2] wl_android_wifi_on: Failed
[ 36.172432@2] dhd_open : wl_android_wifi_on failed (-35)
[ 36.177682@2] dhd_stop: Enter ffffffc052f22000
[ 36.182089@2] wl_android_wifi_off in 1
[ 36.185787@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 36.190629@2] wl_android_wifi_off out
[ 36.194239@2] dhd_stop: Exit
[ 36.197764@2] dhd_open: Exit ret=-1
[ 36.201849@2] dhd_open: Enter ffffffc052f22000
[ 36.205343@2]
[ 36.205343@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 36.205343@2] Compiled in drivers/net/wireless/bcmdhd
[ 36.222808@2] wl_android_wifi_on in 1
[ 36.226430@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 36.231161@2] wifi_platform_set_power = 1
[ 36.235113@2] ======== PULL WL_REG_ON HIGH! ========
[ 36.240071@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 36.446964@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 36.958575@2] sdio_reset_comm():
[ 36.990553@5] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 36.997728@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 37.102991@5] sdio: clk 200000000 SDR mode tuning start
[ 37.107709@5] sdio: rx_tuning_result[0] = 10
[ 37.112473@5] sdio: rx_tuning_result[1] = 10
[ 37.117198@5] sdio: rx_tuning_result[2] = 10
[ 37.121841@5] sdio: rx_tuning_result[3] = 10
[ 37.126180@3] sdio: best_win_start =0, best_win_size =4
[ 37.129956@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 37.137248@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 37.143461@3] sdioh_start: set sd_f2_blocksize 128
[ 37.148525@3]
[ 37.148525@3]
[ 37.148525@3] dhd_bus_devreset: == WLAN ON ==
[ 37.162272@3] F1 signature read @0x18000000=0x15264345
[ 37.170808@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 37.175869@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 37.182567@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 37.187556@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 37.195504@3] dhd_conf_read_config: PM = 0
[ 37.199466@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 37.208170@3] dhdsdio_download_firmware: set use_rxchain 0
[ 37.213626@3] dhdsdio_download_firmware: set txglomsize 40
[ 37.219064@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 37.224555@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 37.230791@3] Final nv_path=/lib/firmware/brcm/
[ 37.235250@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 37.293469@3] dhdsdio_download_nvram: error reading nvram file: -21
[ 37.297617@3] _dhdsdio_download_firmware: dongle nvram file download failed
[ 37.304579@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 37.309890@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 37.315895@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 37.321328@3] wifi_platform_set_power = 0
[ 37.325209@3] ======== PULL WL_REG_ON LOW! ========
[ 37.330070@3] wl_android_wifi_on: Failed
[ 37.333922@3] dhd_open : wl_android_wifi_on failed (-35)
[ 37.339212@3] dhd_stop: Enter ffffffc052f22000
[ 37.343581@3] wl_android_wifi_off in 1
[ 37.347317@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 37.352143@3] wl_android_wifi_off out
[ 37.355847@3] dhd_stop: Exit
[ 37.359528@3] dhd_open: Exit ret=-1
[ 37.366148@3] dhd_open: Enter ffffffc052f22000
[ 37.369923@3]
[ 37.369923@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 37.369923@3] Compiled in drivers/net/wireless/bcmdhd
[ 37.387508@3] wl_android_wifi_on in 1
[ 37.391156@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 37.395824@3] wifi_platform_set_power = 1
[ 37.399818@3] ======== PULL WL_REG_ON HIGH! ========
[ 37.404725@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 37.611652@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 38.118575@3] sdio_reset_comm():
[ 38.254117@7] sdio: clk 200000000 SDR mode tuning start
[ 38.258971@7] sdio: rx_tuning_result[0] = 10
[ 38.263712@7] sdio: rx_tuning_result[1] = 10
[ 38.268351@7] sdio: rx_tuning_result[2] = 10
[ 38.273021@7] sdio: rx_tuning_result[3] = 10
[ 38.277451@0] sdio: best_win_start =0, best_win_size =4
[ 38.281236@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 38.288542@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 38.294744@0] sdioh_start: set sd_f2_blocksize 128
[ 38.299890@0]
[ 38.299890@0]
[ 38.299890@0] dhd_bus_devreset: == WLAN ON ==
[ 38.312461@0] F1 signature read @0x18000000=0x15264345
[ 38.321233@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 38.326380@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 38.333107@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 38.338047@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 38.345980@0] dhd_conf_read_config: PM = 0
[ 38.349981@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 38.358678@0] dhdsdio_download_firmware: set use_rxchain 0
[ 38.364093@0] dhdsdio_download_firmware: set txglomsize 40
[ 38.369562@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 38.375046@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 38.381274@0] Final nv_path=/lib/firmware/brcm/
[ 38.385762@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 38.449033@0] dhdsdio_download_nvram: error reading nvram file: -21
[ 38.453238@0] _dhdsdio_download_firmware: dongle nvram file download failed
[ 38.460193@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 38.465513@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 38.471536@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 38.476938@0] wifi_platform_set_power = 0
[ 38.480850@0] ======== PULL WL_REG_ON LOW! ========
[ 38.485688@0] wl_android_wifi_on: Failed
[ 38.489563@0] dhd_open : wl_android_wifi_on failed (-35)
[ 38.494807@0] dhd_stop: Enter ffffffc052f22000
[ 38.499240@0] wl_android_wifi_off in 1
[ 38.503032@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 38.507740@0] wl_android_wifi_off out
[ 38.511470@0] dhd_stop: Exit
[ 38.515201@0] dhd_open: Exit ret=-1
[ 38.519505@0] dhd_open: Enter ffffffc052f22000
[ 38.523235@0]
[ 38.523235@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 38.523235@0] Compiled in drivers/net/wireless/bcmdhd
[ 38.540961@0] wl_android_wifi_on in 1
[ 38.544574@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 38.549285@0] wifi_platform_set_power = 1
[ 38.553508@0] ======== PULL WL_REG_ON HIGH! ========
[ 38.558148@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 38.765109@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 39.278573@0] sdio_reset_comm():
[ 39.413839@7] sdio: clk 200000000 SDR mode tuning start
[ 39.418676@5] sdio: rx_tuning_result[0] = 10
[ 39.423443@5] sdio: rx_tuning_result[1] = 10
[ 39.428084@5] sdio: rx_tuning_result[2] = 10
[ 39.433016@5] sdio: rx_tuning_result[3] = 10
[ 39.437436@1] sdio: best_win_start =0, best_win_size =4
[ 39.441208@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 39.448515@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 39.454721@1] sdioh_start: set sd_f2_blocksize 128
[ 39.459828@1]
[ 39.459828@1]
[ 39.459828@1] dhd_bus_devreset: == WLAN ON ==
[ 39.472380@1] F1 signature read @0x18000000=0x15264345
[ 39.480855@1] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 39.485966@1] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 39.492704@1] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 39.497658@1] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 39.505590@1] dhd_conf_read_config: PM = 0
[ 39.509559@1] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 39.518273@1] dhdsdio_download_firmware: set use_rxchain 0
[ 39.523736@1] dhdsdio_download_firmware: set txglomsize 40
[ 39.529152@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 39.534658@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 39.540880@1] Final nv_path=/lib/firmware/brcm/
[ 39.545353@1] Final conf_path=/lib/firmware/brcm/config.txt
[ 39.605219@1] dhdsdio_download_nvram: error reading nvram file: -21
[ 39.610004@1] _dhdsdio_download_firmware: dongle nvram file download failed
[ 39.616895@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 39.622229@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 39.628241@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 39.633667@1] wifi_platform_set_power = 0
[ 39.637554@1] ======== PULL WL_REG_ON LOW! ========
[ 39.642417@1] wl_android_wifi_on: Failed
[ 39.646267@1] dhd_open : wl_android_wifi_on failed (-35)
[ 39.651544@1] dhd_stop: Enter ffffffc052f22000
[ 39.655926@1] wl_android_wifi_off in 1
[ 39.659728@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 39.664464@1] wl_android_wifi_off out
[ 39.668169@1] dhd_stop: Exit
[ 39.671897@1] dhd_open: Exit ret=-1
[ 39.678634@1] dhd_open: Enter ffffffc052f22000
[ 39.682365@1]
[ 39.682365@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 39.682365@1] Compiled in drivers/net/wireless/bcmdhd
[ 39.700090@1] wl_android_wifi_on in 1
[ 39.703710@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 39.708400@1] wifi_platform_set_power = 1
[ 39.712383@1] ======== PULL WL_REG_ON HIGH! ========
[ 39.717303@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 39.924223@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 40.438569@1] sdio_reset_comm():
[ 40.470500@4] sdio_read_cis: 10 callbacks suppressed
[ 40.475026@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 40.482600@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 40.490384@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 40.499635@2] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 40.597014@4] sdio: clk 200000000 SDR mode tuning start
[ 40.601719@4] sdio: rx_tuning_result[0] = 10
[ 40.606345@4] sdio: rx_tuning_result[1] = 10
[ 40.610843@4] sdio: rx_tuning_result[2] = 10
[ 40.615900@3] sdio: rx_tuning_result[3] = 10
[ 40.619333@3] sdio: best_win_start =0, best_win_size =4
[ 40.623600@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 40.630967@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 40.637128@3] sdioh_start: set sd_f2_blocksize 128
[ 40.642214@3]
[ 40.642214@3]
[ 40.642214@3] dhd_bus_devreset: == WLAN ON ==
[ 40.653896@3] F1 signature read @0x18000000=0x15264345
[ 40.662384@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 40.667272@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 40.673973@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 40.678998@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 40.686881@3] dhd_conf_read_config: PM = 0
[ 40.690875@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 40.699607@3] dhdsdio_download_firmware: set use_rxchain 0
[ 40.705010@3] dhdsdio_download_firmware: set txglomsize 40
[ 40.710471@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 40.715964@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 40.722199@3] Final nv_path=/lib/firmware/brcm/
[ 40.726659@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 40.785035@3] dhdsdio_download_nvram: error reading nvram file: -21
[ 40.789178@3] _dhdsdio_download_firmware: dongle nvram file download failed
[ 40.796076@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 40.801407@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 40.807417@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 40.812847@3] wifi_platform_set_power = 0
[ 40.816730@3] ======== PULL WL_REG_ON LOW! ========
[ 40.821585@3] wl_android_wifi_on: Failed
[ 40.825443@3] dhd_open : wl_android_wifi_on failed (-35)
[ 40.830732@3] dhd_stop: Enter ffffffc052f22000
[ 40.835102@3] wl_android_wifi_off in 1
[ 40.838834@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 40.843640@3] wl_android_wifi_off out
[ 40.847261@3] dhd_stop: Exit
[ 40.850775@3] dhd_open: Exit ret=-1
[ 40.854861@3] dhd_open: Enter ffffffc052f22000
[ 40.858379@3]
[ 40.858379@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 40.858379@3] Compiled in drivers/net/wireless/bcmdhd
[ 40.875895@3] wl_android_wifi_on in 1
[ 40.879541@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 40.884195@3] wifi_platform_set_power = 1
[ 40.888162@3] ======== PULL WL_REG_ON HIGH! ========
[ 40.893132@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 41.100032@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 41.608574@3] sdio_reset_comm():
[ 41.640472@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 41.648320@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 41.655418@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 41.664549@7] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 41.762550@7] sdio: clk 200000000 SDR mode tuning start
[ 41.767260@7] sdio: rx_tuning_result[0] = 10
[ 41.771873@7] sdio: rx_tuning_result[1] = 10
[ 41.776414@7] sdio: rx_tuning_result[2] = 10
[ 41.780822@7] sdio: rx_tuning_result[3] = 10
[ 41.784934@0] sdio: best_win_start =0, best_win_size =4
[ 41.788720@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 41.796010@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 41.802261@0] sdioh_start: set sd_f2_blocksize 128
[ 41.807321@0]
[ 41.807321@0]
[ 41.807321@0] dhd_bus_devreset: == WLAN ON ==
[ 41.819025@0] F1 signature read @0x18000000=0x15264345
[ 41.827586@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 41.832590@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 41.839231@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 41.844187@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 41.852146@0] dhd_conf_read_config: PM = 0
[ 41.856074@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 41.864819@0] dhdsdio_download_firmware: set use_rxchain 0
[ 41.870272@0] dhdsdio_download_firmware: set txglomsize 40
[ 41.875666@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 41.881204@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 41.887418@0] Final nv_path=/lib/firmware/brcm/
[ 41.891895@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 41.954686@0] dhdsdio_download_nvram: error reading nvram file: -21
[ 41.958772@0] _dhdsdio_download_firmware: dongle nvram file download failed
[ 41.965725@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 41.971010@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 41.977028@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 41.982481@0] wifi_platform_set_power = 0
[ 41.986678@0] ======== PULL WL_REG_ON LOW! ========
[ 41.991191@0] wl_android_wifi_on: Failed
[ 41.995055@0] dhd_open : wl_android_wifi_on failed (-35)
[ 42.000352@0] dhd_stop: Enter ffffffc052f22000
[ 42.004714@0] wl_android_wifi_off in 1
[ 42.008421@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 42.013269@0] wl_android_wifi_off out
[ 42.016897@0] dhd_stop: Exit
[ 42.020450@0] dhd_open: Exit ret=-1
[ 42.026936@0] dhd_open: Enter ffffffc052f22000
[ 42.030489@0]
[ 42.030489@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 42.030489@0] Compiled in drivers/net/wireless/bcmdhd
[ 42.048037@0] wl_android_wifi_on in 1
[ 42.051713@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 42.056335@0] wifi_platform_set_power = 1
[ 42.060321@0] ======== PULL WL_REG_ON HIGH! ========
[ 42.065260@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 42.272153@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 42.778572@0] sdio_reset_comm():
[ 42.810535@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 42.817715@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 42.922809@4] sdio: clk 200000000 SDR mode tuning start
[ 42.927530@4] sdio: rx_tuning_result[0] = 10
[ 42.932302@4] sdio: rx_tuning_result[1] = 10
[ 42.937035@4] sdio: rx_tuning_result[2] = 10
[ 42.941701@4] sdio: rx_tuning_result[3] = 10
[ 42.946042@1] sdio: best_win_start =0, best_win_size =4
[ 42.949815@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 42.957124@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 42.963325@1] sdioh_start: set sd_f2_blocksize 128
[ 42.968397@1]
[ 42.968397@1]
[ 42.968397@1] dhd_bus_devreset: == WLAN ON ==
[ 42.980557@1] F1 signature read @0x18000000=0x15264345
[ 42.989044@1] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 42.994071@1] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 43.000762@1] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 43.005766@1] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 43.013713@1] dhd_conf_read_config: PM = 0
[ 43.017651@1] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 43.026393@1] dhdsdio_download_firmware: set use_rxchain 0
[ 43.031837@1] dhdsdio_download_firmware: set txglomsize 40
[ 43.037245@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 43.042789@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 43.048989@1] Final nv_path=/lib/firmware/brcm/
[ 43.053459@1] Final conf_path=/lib/firmware/brcm/config.txt
[ 43.113527@1] dhdsdio_download_nvram: error reading nvram file: -21
[ 43.117663@1] _dhdsdio_download_firmware: dongle nvram file download failed
[ 43.124617@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 43.129940@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 43.135941@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 43.141369@1] wifi_platform_set_power = 0
[ 43.145256@1] ======== PULL WL_REG_ON LOW! ========
[ 43.150107@1] wl_android_wifi_on: Failed
[ 43.153969@1] dhd_open : wl_android_wifi_on failed (-35)
[ 43.159262@1] dhd_stop: Enter ffffffc052f22000
[ 43.163628@1] wl_android_wifi_off in 1
[ 43.167352@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 43.172179@1] wl_android_wifi_off out
[ 43.175877@1] dhd_stop: Exit
[ 43.179540@1] dhd_open: Exit ret=-1
[ 43.183728@1] dhd_open: Enter ffffffc052f22000
[ 43.187962@1]
[ 43.187962@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 43.187962@1] Compiled in drivers/net/wireless/bcmdhd
[ 43.207284@1] wl_android_wifi_on in 1
[ 43.210936@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 43.215585@1] wifi_platform_set_power = 1
[ 43.219841@1] ======== PULL WL_REG_ON HIGH! ========
[ 43.224488@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 43.431410@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 43.938568@1] sdio_reset_comm():
[ 44.073706@5] sdio: clk 200000000 SDR mode tuning start
[ 44.078494@5] sdio: rx_tuning_result[0] = 10
[ 44.083216@5] sdio: rx_tuning_result[1] = 10
[ 44.087872@5] sdio: rx_tuning_result[2] = 10
[ 44.092541@5] sdio: rx_tuning_result[3] = 10
[ 44.096957@2] sdio: best_win_start =0, best_win_size =4
[ 44.100717@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 44.108025@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 44.114228@2] sdioh_start: set sd_f2_blocksize 128
[ 44.119329@2]
[ 44.119329@2]
[ 44.119329@2] dhd_bus_devreset: == WLAN ON ==
[ 44.131872@2] F1 signature read @0x18000000=0x15264345
[ 44.140445@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 44.145598@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 44.152322@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 44.157288@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 44.165221@2] dhd_conf_read_config: PM = 0
[ 44.169373@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 44.177903@2] dhdsdio_download_firmware: set use_rxchain 0
[ 44.183347@2] dhdsdio_download_firmware: set txglomsize 40
[ 44.188783@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 44.194288@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 44.200531@2] Final nv_path=/lib/firmware/brcm/
[ 44.204983@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 44.265531@2] dhdsdio_download_nvram: error reading nvram file: -21
[ 44.269764@2] _dhdsdio_download_firmware: dongle nvram file download failed
[ 44.276664@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 44.281991@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 44.288009@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 44.293430@2] wifi_platform_set_power = 0
[ 44.297323@2] ======== PULL WL_REG_ON LOW! ========
[ 44.302166@2] wl_android_wifi_on: Failed
[ 44.306036@2] dhd_open : wl_android_wifi_on failed (-35)
[ 44.311310@2] dhd_stop: Enter ffffffc052f22000
[ 44.315694@2] wl_android_wifi_off in 1
[ 44.319497@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 44.324232@2] wl_android_wifi_off out
[ 44.327935@2] dhd_stop: Exit
[ 44.331652@2] dhd_open: Exit ret=-1
[ 44.338316@2] dhd_open: Enter ffffffc052f22000
[ 44.342082@2]
[ 44.342082@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 44.342082@2] Compiled in drivers/net/wireless/bcmdhd
[ 44.359776@2] wl_android_wifi_on in 1
[ 44.363389@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 44.368125@2] wifi_platform_set_power = 1
[ 44.372114@2] ======== PULL WL_REG_ON HIGH! ========
[ 44.377028@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 44.583941@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 45.098574@2] sdio_reset_comm():
[ 45.233972@7] sdio: clk 200000000 SDR mode tuning start
[ 45.238838@5] sdio: rx_tuning_result[0] = 10
[ 45.243578@5] sdio: rx_tuning_result[1] = 10
[ 45.248214@5] sdio: rx_tuning_result[2] = 10
[ 45.252910@5] sdio: rx_tuning_result[3] = 10
[ 45.257338@3] sdio: best_win_start =0, best_win_size =4
[ 45.261113@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 45.268406@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 45.274622@3] sdioh_start: set sd_f2_blocksize 128
[ 45.279707@3]
[ 45.279707@3]
[ 45.279707@3] dhd_bus_devreset: == WLAN ON ==
[ 45.292275@3] F1 signature read @0x18000000=0x15264345
[ 45.300783@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 45.305901@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 45.312630@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 45.317593@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 45.325541@3] dhd_conf_read_config: PM = 0
[ 45.329504@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 45.338207@3] dhdsdio_download_firmware: set use_rxchain 0
[ 45.343665@3] dhdsdio_download_firmware: set txglomsize 40
[ 45.349101@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 45.354592@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 45.360826@3] Final nv_path=/lib/firmware/brcm/
[ 45.365287@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 45.423819@3] dhdsdio_download_nvram: error reading nvram file: -21
[ 45.428024@3] _dhdsdio_download_firmware: dongle nvram file download failed
[ 45.434986@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 45.440300@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 45.446303@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 45.451734@3] wifi_platform_set_power = 0
[ 45.455617@3] ======== PULL WL_REG_ON LOW! ========
[ 45.460476@3] wl_android_wifi_on: Failed
[ 45.464330@3] dhd_open : wl_android_wifi_on failed (-35)
[ 45.469619@3] dhd_stop: Enter ffffffc052f22000
[ 45.473989@3] wl_android_wifi_off in 1
[ 45.477779@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 45.482552@3] wl_android_wifi_off out
[ 45.486268@3] dhd_stop: Exit
[ 45.489998@3] dhd_open: Exit ret=-1
[ 45.494287@3] dhd_open: Enter ffffffc052f22000
[ 45.498658@3]
[ 45.498658@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 45.498658@3] Compiled in drivers/net/wireless/bcmdhd
[ 45.516363@3] wl_android_wifi_on in 1
[ 45.520005@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 45.524687@3] wifi_platform_set_power = 1
[ 45.528688@3] ======== PULL WL_REG_ON HIGH! ========
[ 45.533589@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 45.740513@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 46.248574@3] sdio_reset_comm():
[ 46.280494@7] sdio_read_cis: 10 callbacks suppressed
[ 46.285030@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 46.292597@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 46.299680@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 46.308920@0] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 46.406304@5] sdio: clk 200000000 SDR mode tuning start
[ 46.513866@1] dhdsdio_download_firmware: set txglomsize 40
[ 46.519301@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 46.524806@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 46.531040@1] Final nv_path=/lib/firmware/brcm/
[ 46.535501@1] Final conf_path=/lib/firmware/brcm/config.txt
[ 46.595351@1] dhdsdio_download_nvram: error reading nvram file: -21
[ 46.599467@1] _dhdsdio_download_firmware: dongle nvram file download failed
[ 46.606378@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 46.611708@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 46.617725@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 46.623166@1] wifi_platform_set_power = 0
[ 46.627039@1] ======== PULL WL_REG_ON LOW! ========
[ 46.631883@1] wl_android_wifi_on: Failed
[ 46.635751@1] dhd_open : wl_android_wifi_on failed (-35)
[ 46.641026@1] dhd_stop: Enter ffffffc052f22000
[ 46.645410@1] wl_android_wifi_off in 1
[ 46.649143@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 46.653948@1] wl_android_wifi_off out
[ 46.657571@1] dhd_stop: Exit
[ 46.661075@1] dhd_open: Exit ret=-1
[ 46.667544@1] dhd_open: Enter ffffffc052f22000
[ 46.671103@1]
[ 46.671103@1] Dongle Host D
[ 46.519301@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 46.524806@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 46.531040@1] Final nv_path=/lib/firmware/brcm/
[ 46.535501@1] Final conf_path=/lib/firmware/brcm/config.txt
[ 46.595351@1] dhdsdio_download_nvram: error reading nvram file: -21
[ 46.599467@1] _dhdsdio_download_firmware: dongle nvram file download failed
[ 46.606378@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 46.611708@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 46.617725@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 46.623166@1] wifi_platform_set_power = 0
[ 46.627039@1] ======== PULL WL_REG_ON LOW! ========
[ 46.631883@1] wl_android_wifi_on: Failed
[ 46.635751@1] dhd_open : wl_android_wifi_on failed (-35)
[ 46.641026@1] dhd_stop: Enter ffffffc052f22000
[ 46.645410@1] wl_android_wifi_off in 1
[ 46.649143@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 46.653948@1] wl_android_wifi_off out
[ 46.657571@1] dhd_stop: Exit
[ 46.661075@1] dhd_open: Exit ret=-1
[ 46.667544@1] dhd_open: Enter ffffffc052f22000
[ 46.671103@1]
[ 46.671103@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 46.671103@1] Compiled in drivers/net/wireless/bcmdhd
[ 46.688612@1] wl_android_wifi_on in 1
[ 46.692219@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 46.696927@1] wifi_platform_set_power = 1
[ 46.700917@1] ======== PULL WL_REG_ON HIGH! ========
[ 46.705830@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 46.912743@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 47.418570@1] sdio_reset_comm():
[ 47.450512@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 47.457682@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 47.464784@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 47.473915@7] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 47.571612@7] sdio: clk 200000000 SDR mode tuning start
[ 47.576286@7] sdio: rx_tuning_result[0] = 10
[ 47.580909@7] sdio: rx_tuning_result[1] = 10
[ 47.585454@7] sdio: rx_tuning_result[2] = 10
[ 47.589906@4] sdio: rx_tuning_result[3] = 10
[ 47.594000@2] sdio: best_win_start =0, best_win_size =4
[ 47.597732@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 47.605106@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 47.611270@2] sdioh_start: set sd_f2_blocksize 128
[ 47.616339@2]
[ 47.616339@2]
[ 47.616339@2] dhd_bus_devreset: == WLAN ON ==
[ 47.628031@2] F1 signature read @0x18000000=0x15264345
[ 47.636690@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 47.641643@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 47.648296@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 47.653310@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 47.661236@2] dhd_conf_read_config: PM = 0
[ 47.665180@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 47.673927@2] dhdsdio_download_firmware: set use_rxchain 0
[ 47.679353@2] dhdsdio_download_firmware: set txglomsize 40
[ 47.684775@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 47.690306@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 47.696504@2] Final nv_path=/lib/firmware/brcm/
[ 47.701001@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 47.761587@2] dhdsdio_download_nvram: error reading nvram file: -21
[ 47.765659@2] _dhdsdio_download_firmware: dongle nvram file download failed
[ 47.772613@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 47.777902@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 47.783952@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 47.789367@2] wifi_platform_set_power = 0
[ 47.793562@2] ======== PULL WL_REG_ON LOW! ========
[ 47.798080@2] wl_android_wifi_on: Failed
[ 47.802326@2] dhd_open : wl_android_wifi_on failed (-35)
[ 47.807226@2] dhd_stop: Enter ffffffc052f22000
[ 47.811635@2] wl_android_wifi_off in 1
[ 47.815893@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 47.820172@2] wl_android_wifi_off out
[ 47.824286@2] dhd_stop: Exit
[ 47.827842@2] dhd_open: Exit ret=-1
[ 47.831912@2] dhd_open: Enter ffffffc052f22000
[ 47.835409@2]
[ 47.835409@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 47.835409@2] Compiled in drivers/net/wireless/bcmdhd
[ 47.852880@2] wl_android_wifi_on in 1
[ 47.856501@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 47.861232@2] wifi_platform_set_power = 1
[ 47.865184@2] ======== PULL WL_REG_ON HIGH! ========
[ 47.870141@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 48.077018@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 48.588574@2] sdio_reset_comm():
[ 48.620544@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 48.627712@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 48.733127@7] sdio: clk 200000000 SDR mode tuning start
[ 48.737850@7] sdio: rx_tuning_result[0] = 10
[ 48.742637@4] sdio: rx_tuning_result[1] = 10
[ 48.747379@4] sdio: rx_tuning_result[2] = 10
[ 48.752027@4] sdio: rx_tuning_result[3] = 10
[ 48.756368@3] sdio: best_win_start =0, best_win_size =4
[ 48.760143@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 48.767439@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 48.773651@3] sdioh_start: set sd_f2_blocksize 128
[ 48.778729@3]
[ 48.778729@3]
[ 48.778729@3] dhd_bus_devreset: == WLAN ON ==
[ 48.790884@3] F1 signature read @0x18000000=0x15264345
[ 48.799405@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 48.804431@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 48.811155@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 48.816117@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 48.824063@3] dhd_conf_read_config: PM = 0
[ 48.828004@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 48.836762@3] dhdsdio_download_firmware: set use_rxchain 0
[ 48.842189@3] dhdsdio_download_firmware: set txglomsize 40
[ 48.847597@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 48.853141@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 48.859354@3] Final nv_path=/lib/firmware/brcm/
[ 48.863811@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 48.922863@3] dhdsdio_download_nvram: error reading nvram file: -21
[ 48.927022@3] _dhdsdio_download_firmware: dongle nvram file download failed
[ 48.933984@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 48.939293@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 48.945302@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 48.950736@3] wifi_platform_set_power = 0
[ 48.955047@3] ======== PULL WL_REG_ON LOW! ========
[ 48.959474@3] wl_android_wifi_on: Failed
[ 48.963328@3] dhd_open : wl_android_wifi_on failed (-35)
[ 48.968620@3] dhd_stop: Enter ffffffc052f22000
[ 48.972987@3] wl_android_wifi_off in 1
[ 48.976732@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 48.981551@3] wl_android_wifi_off out
[ 48.985267@3] dhd_stop: Exit
[ 48.988961@3] dhd_open: Exit ret=-1
[ 48.995557@3] dhd_open: Enter ffffffc052f22000
[ 48.999309@3]
[ 48.999309@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 48.999309@3] Compiled in drivers/net/wireless/bcmdhd
[ 49.016914@3] wl_android_wifi_on in 1
[ 49.020577@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 49.025230@3] wifi_platform_set_power = 1
[ 49.029223@3] ======== PULL WL_REG_ON HIGH! ========
[ 49.034132@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 49.241060@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 49.748582@3] sdio_reset_comm():
[ 49.884010@7] sdio: clk 200000000 SDR mode tuning start
[ 49.888885@7] sdio: rx_tuning_result[0] = 10
[ 49.893622@7] sdio: rx_tuning_result[1] = 10
[ 49.898261@7] sdio: rx_tuning_result[2] = 10
[ 49.902945@7] sdio: rx_tuning_result[3] = 10
[ 49.907379@0] sdio: best_win_start =0, best_win_size =4
[ 49.911146@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 49.918472@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 49.924674@0] sdioh_start: set sd_f2_blocksize 128
[ 49.929798@0]
[ 49.929798@0]
[ 49.929798@0] dhd_bus_devreset: == WLAN ON ==
[ 49.942419@0] F1 signature read @0x18000000=0x15264345
[ 49.951147@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 49.956300@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 49.963020@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 49.968003@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 49.975905@0] dhd_conf_read_config: PM = 0
[ 49.979879@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 49.988624@0] dhdsdio_download_firmware: set use_rxchain 0
[ 49.994017@0] dhdsdio_download_firmware: set txglomsize 40
[ 49.999491@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 50.004971@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 50.011198@0] Final nv_path=/lib/firmware/brcm/
[ 50.015686@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 50.078120@0] dhdsdio_download_nvram: error reading nvram file: -21
[ 50.082389@0] _dhdsdio_download_firmware: dongle nvram file download failed
[ 50.089289@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 50.094578@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 50.100652@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 50.106028@0] wifi_platform_set_power = 0
[ 50.109946@0] ======== PULL WL_REG_ON LOW! ========
[ 50.114759@0] wl_android_wifi_on: Failed
[ 50.118677@0] dhd_open : wl_android_wifi_on failed (-35)
[ 50.123903@0] dhd_stop: Enter ffffffc052f22000
[ 50.128298@0] wl_android_wifi_off in 1
[ 50.132134@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 50.136838@0] wl_android_wifi_off out
[ 50.140567@0] dhd_stop: Exit
[ 50.144284@0] dhd_open: Exit ret=-1
[ 50.148668@0] dhd_open: Enter ffffffc052f22000
[ 50.152968@0]
[ 50.152968@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 50.152968@0] Compiled in drivers/net/wireless/bcmdhd
[ 50.172504@0] wl_android_wifi_on in 1
[ 50.176124@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 50.180812@0] wifi_platform_set_power = 1
[ 50.184781@0] ======== PULL WL_REG_ON HIGH! ========
[ 50.189715@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 50.396595@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 50.908574@0] sdio_reset_comm():
[ 51.043773@5] sdio: clk 200000000 SDR mode tuning start
[ 51.048582@7] sdio: rx_tuning_result[0] = 10
[ 51.053342@7] sdio: rx_tuning_result[1] = 10
[ 51.057984@7] sdio: rx_tuning_result[2] = 10
[ 51.062662@7] sdio: rx_tuning_result[3] = 10
[ 51.067081@1] sdio: best_win_start =0, best_win_size =4
[ 51.070860@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 51.078154@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 51.084362@1] sdioh_start: set sd_f2_blocksize 128
[ 51.089446@1]
[ 51.089446@1]
[ 51.089446@1] dhd_bus_devreset: == WLAN ON ==
[ 51.102006@1] F1 signature read @0x18000000=0x15264345
[ 51.110570@1] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 51.115709@1] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 51.122377@1] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 51.127375@1] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 51.135324@1] dhd_conf_read_config: PM = 0
[ 51.139276@1] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 51.147990@1] dhdsdio_download_firmware: set use_rxchain 0
[ 51.153434@1] dhdsdio_download_firmware: set txglomsize 40
[ 51.158881@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 51.164374@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 51.170597@1] Final nv_path=/lib/firmware/brcm/
[ 51.175070@1] Final conf_path=/lib/firmware/brcm/config.txt
[ 51.235051@1] dhdsdio_download_nvram: error reading nvram file: -21
[ 51.239259@1] _dhdsdio_download_firmware: dongle nvram file download failed
[ 51.246176@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 51.251514@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 51.257519@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 51.262940@1] wifi_platform_set_power = 0
[ 51.267210@1] ======== PULL WL_REG_ON LOW! ========
[ 51.271675@1] wl_android_wifi_on: Failed
[ 51.276055@1] dhd_open : wl_android_wifi_on failed (-35)
[ 51.280831@1] dhd_stop: Enter ffffffc052f22000
[ 51.285279@1] wl_android_wifi_off in 1
[ 51.289693@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 51.294083@1] wl_android_wifi_off out
[ 51.298384@1] dhd_stop: Exit
[ 51.302708@1] dhd_open: Exit ret=-1
[ 51.310041@1] dhd_open: Enter ffffffc052f22000
[ 51.313764@1]
[ 51.313764@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 51.313764@1] Compiled in drivers/net/wireless/bcmdhd
[ 51.331446@1] wl_android_wifi_on in 1
[ 51.335068@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 51.339817@1] wifi_platform_set_power = 1
[ 51.343741@1] ======== PULL WL_REG_ON HIGH! ========
[ 51.348704@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 51.555586@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 52.068565@1] sdio_reset_comm():
[ 52.100525@4] sdio_read_cis: 10 callbacks suppressed
[ 52.105040@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 52.112614@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 52.119699@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 52.128929@2] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 52.226499@7] sdio: clk 200000000 SDR mode tuning start
[ 52.231195@7] sdio: rx_tuning_result[0] = 10
[ 52.235807@7] sdio: rx_tuning_result[1] = 10
[ 52.240294@7] sdio: rx_tuning_result[2] = 10
[ 52.244661@7] sdio: rx_tuning_result[3] = 10
[ 52.248723@3] sdio: best_win_start =0, best_win_size =4
[ 52.252541@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 52.259913@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 52.266069@3] sdioh_start: set sd_f2_blocksize 128
[ 52.271175@3]
[ 52.271175@3]
[ 52.271175@3] dhd_bus_devreset: == WLAN ON ==
[ 52.282847@3] F1 signature read @0x18000000=0x15264345
[ 52.291354@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 52.296281@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 52.302997@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 52.307965@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 52.315914@3] dhd_conf_read_config: PM = 0
[ 52.319880@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 52.328604@3] dhdsdio_download_firmware: set use_rxchain 0
[ 52.334012@3] dhdsdio_download_firmware: set txglomsize 40
[ 52.339473@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 52.344965@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 52.351202@3] Final nv_path=/lib/firmware/brcm/
[ 52.355660@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 52.414704@3] dhdsdio_download_nvram: error reading nvram file: -21
[ 52.418838@3] _dhdsdio_download_firmware: dongle nvram file download failed
[ 52.425737@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 52.431078@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 52.437082@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 52.442511@3] wifi_platform_set_power = 0
[ 52.446716@3] ======== PULL WL_REG_ON LOW! ========
[ 52.451250@3] wl_android_wifi_on: Failed
[ 52.455470@3] dhd_open : wl_android_wifi_on failed (-35)
[ 52.460397@3] dhd_stop: Enter ffffffc052f22000
[ 52.464767@3] wl_android_wifi_off in 1
[ 52.469045@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 52.473305@3] wl_android_wifi_off out
[ 52.477466@3] dhd_stop: Exit
[ 52.481552@3] dhd_open: Exit ret=-1
[ 52.486199@3] dhd_open: Enter ffffffc052f22000
[ 52.489751@3]
[ 52.489751@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 52.489751@3] Compiled in drivers/net/wireless/bcmdhd
[ 52.507243@3] wl_android_wifi_on in 1
[ 52.510893@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 52.515578@3] wifi_platform_set_power = 1
[ 52.519574@3] ======== PULL WL_REG_ON HIGH! ========
[ 52.524479@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 52.731416@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 53.238574@3] sdio_reset_comm():
[ 53.270543@5] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 53.277713@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 53.284810@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 53.293949@5] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 53.391935@5] sdio: clk 200000000 SDR mode tuning start
[ 53.397291@5] sdio: rx_tuning_result[0] = 10
[ 53.401932@5] sdio: rx_tuning_result[1] = 10
[ 53.406468@5] sdio: rx_tuning_result[2] = 10
[ 53.410987@0] sdio: rx_tuning_result[3] = 10
[ 53.414376@0] sdio: best_win_start =0, best_win_size =4
[ 53.418721@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 53.426003@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 53.432233@0] sdioh_start: set sd_f2_blocksize 128
[ 53.437291@0]
[ 53.437291@0]
[ 53.437291@0] dhd_bus_devreset: == WLAN ON ==
[ 53.449005@0] F1 signature read @0x18000000=0x15264345
[ 53.457560@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 53.462562@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 53.469246@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 53.474163@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 53.482129@0] dhd_conf_read_config: PM = 0
[ 53.486049@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 53.494795@0] dhdsdio_download_firmware: set use_rxchain 0
[ 53.500246@0] dhdsdio_download_firmware: set txglomsize 40
[ 53.505642@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 53.511180@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 53.517394@0] Final nv_path=/lib/firmware/brcm/
[ 53.521875@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 53.585144@0] dhdsdio_download_nvram: error reading nvram file: -21
[ 53.589223@0] _dhdsdio_download_firmware: dongle nvram file download failed
[ 53.596142@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 53.601490@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 53.607479@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 53.612906@0] wifi_platform_set_power = 0
[ 53.616816@0] ======== PULL WL_REG_ON LOW! ========
[ 53.621642@0] wl_android_wifi_on: Failed
[ 53.625506@0] dhd_open : wl_android_wifi_on failed (-35)
[ 53.630786@0] dhd_stop: Enter ffffffc052f22000
[ 53.635187@0] wl_android_wifi_off in 1
[ 53.638891@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 53.643708@0] wl_android_wifi_off out
[ 53.647324@0] dhd_stop: Exit
[ 53.650898@0] dhd_open: Exit ret=-1
[ 53.657370@0] dhd_open: Enter ffffffc052f22000
[ 53.660916@0]
[ 53.660916@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 53.660916@0] Compiled in drivers/net/wireless/bcmdhd
[ 53.678443@0] wl_android_wifi_on in 1
[ 53.682125@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 53.686739@0] wifi_platform_set_power = 1
[ 53.690722@0] ======== PULL WL_REG_ON HIGH! ========
[ 53.695639@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 53.902586@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 54.408572@0] sdio_reset_comm():
[ 54.440490@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 54.447673@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 54.552777@7] sdio: clk 200000000 SDR mode tuning start
[ 54.557503@7] sdio: rx_tuning_result[0] = 10
[ 54.562277@4] sdio: rx_tuning_result[1] = 10
[ 54.567012@4] sdio: rx_tuning_result[2] = 10
[ 54.571658@4] sdio: rx_tuning_result[3] = 10
[ 54.576001@1] sdio: best_win_start =0, best_win_size =4
[ 54.579774@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 54.587072@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 54.593280@1] sdioh_start: set sd_f2_blocksize 128
[ 54.598344@1]
[ 54.598344@1]
[ 54.598344@1] dhd_bus_devreset: == WLAN ON ==
[ 54.612137@1] F1 signature read @0x18000000=0x15264345
[ 54.620689@1] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 54.625764@1] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 54.632457@1] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 54.637457@1] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 54.645404@1] dhd_conf_read_config: PM = 0
[ 54.649422@1] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 54.658071@1] dhdsdio_download_firmware: set use_rxchain 0
[ 54.663516@1] dhdsdio_download_firmware: set txglomsize 40
[ 54.668963@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 54.674457@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 54.680679@1] Final nv_path=/lib/firmware/brcm/
[ 54.685152@1] Final conf_path=/lib/firmware/brcm/config.txt
[ 54.744884@1] dhdsdio_download_nvram: error reading nvram file: -21
[ 54.749057@1] _dhdsdio_download_firmware: dongle nvram file download failed
[ 54.755976@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 54.761311@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 54.767316@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 54.772737@1] wifi_platform_set_power = 0
[ 54.776629@1] ======== PULL WL_REG_ON LOW! ========
[ 54.781472@1] wl_android_wifi_on: Failed
[ 54.785341@1] dhd_open : wl_android_wifi_on failed (-35)
[ 54.790628@1] dhd_stop: Enter ffffffc052f22000
[ 54.795000@1] wl_android_wifi_off in 1
[ 54.798751@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 54.803538@1] wl_android_wifi_off out
[ 54.807242@1] dhd_stop: Exit
[ 54.810926@1] dhd_open: Exit ret=-1
[ 54.815141@1] dhd_open: Enter ffffffc052f22000
[ 54.818872@1]
[ 54.818872@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 54.818872@1] Compiled in drivers/net/wireless/bcmdhd
[ 54.836426@1] wl_android_wifi_on in 1
[ 54.840067@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 54.844776@1] wifi_platform_set_power = 1
[ 54.848769@1] ======== PULL WL_REG_ON HIGH! ========
[ 54.853678@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 55.060591@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 55.568580@3] sdio_reset_comm():
[ 55.703752@7] sdio: clk 200000000 SDR mode tuning start
[ 55.708577@7] sdio: rx_tuning_result[0] = 10
[ 55.713329@7] sdio: rx_tuning_result[1] = 10
[ 55.717976@7] sdio: rx_tuning_result[2] = 10
[ 55.722657@7] sdio: rx_tuning_result[3] = 10
[ 55.727082@2] sdio: best_win_start =0, best_win_size =4
[ 55.730848@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 55.738156@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 55.744361@2] sdioh_start: set sd_f2_blocksize 128
[ 55.749466@2]
[ 55.749466@2]
[ 55.749466@2] dhd_bus_devreset: == WLAN ON ==
[ 55.762038@2] F1 signature read @0x18000000=0x15264345
[ 55.770591@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 55.775751@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 55.782473@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 55.787446@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 55.795377@2] dhd_conf_read_config: PM = 0
[ 55.799554@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 55.808060@2] dhdsdio_download_firmware: set use_rxchain 0
[ 55.813505@2] dhdsdio_download_firmware: set txglomsize 40
[ 55.818939@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 55.824445@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 55.830667@2] Final nv_path=/lib/firmware/brcm/
[ 55.835140@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 55.895628@2] dhdsdio_download_nvram: error reading nvram file: -21
[ 55.899856@2] _dhdsdio_download_firmware: dongle nvram file download failed
[ 55.906768@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 55.912097@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 55.918114@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 55.923535@2] wifi_platform_set_power = 0
[ 55.927428@2] ======== PULL WL_REG_ON LOW! ========
[ 55.932273@2] wl_android_wifi_on: Failed
[ 55.936141@2] dhd_open : wl_android_wifi_on failed (-35)
[ 55.941415@2] dhd_stop: Enter ffffffc052f22000
[ 55.945800@2] wl_android_wifi_off in 1
[ 55.949609@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 55.954337@2] wl_android_wifi_off out
[ 55.958049@2] dhd_stop: Exit
[ 55.961775@2] dhd_open: Exit ret=-1
[ 55.968460@2] dhd_open: Enter ffffffc052f22000
[ 55.972239@2]
[ 55.972239@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 55.972239@2] Compiled in drivers/net/wireless/bcmdhd
[ 55.989943@2] wl_android_wifi_on in 1
[ 55.993563@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 55.998291@2] wifi_platform_set_power = 1
[ 56.002301@2] ======== PULL WL_REG_ON HIGH! ========
[ 56.007194@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 56.214106@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 56.728571@2] sdio_reset_comm():
[ 56.863945@7] sdio: clk 200000000 SDR mode tuning start
[ 56.868788@7] sdio: rx_tuning_result[0] = 10
[ 56.873537@7] sdio: rx_tuning_result[1] = 10
[ 56.878183@7] sdio: rx_tuning_result[2] = 10
[ 56.882869@7] sdio: rx_tuning_result[3] = 10
[ 56.887295@3] sdio: best_win_start =0, best_win_size =4
[ 56.891069@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 56.898364@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 56.904580@3] sdioh_start: set sd_f2_blocksize 128
[ 56.909664@3]
[ 56.909664@3]
[ 56.909664@3] dhd_bus_devreset: == WLAN ON ==
[ 56.922257@3] F1 signature read @0x18000000=0x15264345
[ 56.930738@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 56.935859@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 56.942581@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 56.947551@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 56.955497@3] dhd_conf_read_config: PM = 0
[ 56.959465@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 56.968166@3] dhdsdio_download_firmware: set use_rxchain 0
[ 56.973629@3] dhdsdio_download_firmware: set txglomsize 40
[ 56.979060@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 56.984550@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 56.990787@3] Final nv_path=/lib/firmware/brcm/
[ 56.995246@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 57.053683@3] dhdsdio_download_nvram: error reading nvram file: -21
[ 57.058431@3] _dhdsdio_download_firmware: dongle nvram file download failed
[ 57.065401@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 57.070702@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 57.076710@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 57.082141@3] wifi_platform_set_power = 0
[ 57.086024@3] ======== PULL WL_REG_ON LOW! ========
[ 57.090882@3] wl_android_wifi_on: Failed
[ 57.094737@3] dhd_open : wl_android_wifi_on failed (-35)
[ 57.100023@3] dhd_stop: Enter ffffffc052f22000
[ 57.104396@3] wl_android_wifi_off in 1
[ 57.108185@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 57.112959@3] wl_android_wifi_off out
[ 57.116677@3] dhd_stop: Exit
[ 57.120407@3] dhd_open: Exit ret=-1
[ 57.124701@3] dhd_open: Enter ffffffc052f22000
[ 57.128415@3]
[ 57.128415@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 57.128415@3] Compiled in drivers/net/wireless/bcmdhd
[ 57.146134@3] wl_android_wifi_on in 1
[ 57.149780@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 57.154429@3] wifi_platform_set_power = 1
[ 57.158396@3] ======== PULL WL_REG_ON HIGH! ========
[ 57.163361@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 57.370261@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 57.822082@5] usb 1-1.3: USB disconnect, device number 4
[ 57.878611@3] sdio_reset_comm():
[ 57.910596@4] sdio_read_cis: 10 callbacks suppressed
[ 57.915140@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 57.923067@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 57.930275@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 57.939561@2] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 58.036805@7] sdio: clk 200000000 SDR mode tuning start
[ 58.041540@5] sdio: rx_tuning_result[0] = 10
[ 58.046134@5] sdio: rx_tuning_result[1] = 10
[ 58.050614@5] sdio: rx_tuning_result[2] = 10
[ 58.054986@5] sdio: rx_tuning_result[3] = 10
[ 58.059033@3] sdio: best_win_start =0, best_win_size =4
[ 58.062868@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 58.070242@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 58.076391@3] sdioh_start: set sd_f2_blocksize 128
[ 58.081504@3]
[ 58.081504@3]
[ 58.081504@3] dhd_bus_devreset: == WLAN ON ==
[ 58.093238@3] F1 signature read @0x18000000=0x15264345
[ 58.101768@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 58.106640@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 58.113364@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 58.118326@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 58.126271@3] dhd_conf_read_config: PM = 0
[ 58.130238@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 58.138968@3] dhdsdio_download_firmware: set use_rxchain 0
[ 58.144372@3] dhdsdio_download_firmware: set txglomsize 40
[ 58.149830@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 58.155326@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 58.161563@3] Final nv_path=/lib/firmware/brcm/
[ 58.166021@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 58.224980@3] dhdsdio_download_nvram: error reading nvram file: -21
[ 58.229155@3] _dhdsdio_download_firmware: dongle nvram file download failed
[ 58.236061@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 58.241390@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 58.247400@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 58.252830@3] wifi_platform_set_power = 0
[ 58.256713@3] ======== PULL WL_REG_ON LOW! ========
[ 58.261569@3] wl_android_wifi_on: Failed
[ 58.265425@3] dhd_open : wl_android_wifi_on failed (-35)
[ 58.270712@3] dhd_stop: Enter ffffffc052f22000
[ 58.275084@3] wl_android_wifi_off in 1
[ 58.278820@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 58.283622@3] wl_android_wifi_off out
[ 58.287244@3] dhd_stop: Exit
[ 58.290772@3] dhd_open: Exit ret=-1
[ 58.297245@3] dhd_open: Enter ffffffc052f22000
[ 58.300835@3]
[ 58.300835@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 58.300835@3] Compiled in drivers/net/wireless/bcmdhd
[ 58.318354@3] wl_android_wifi_on in 1
[ 58.322016@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 58.326688@3] wifi_platform_set_power = 1
[ 58.330681@3] ======== PULL WL_REG_ON HIGH! ========
[ 58.335591@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 58.542519@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 59.048578@0] sdio_reset_comm():
[ 59.080512@5] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 59.087679@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 59.094776@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 59.103905@5] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 59.201683@5] sdio: clk 200000000 SDR mode tuning start
[ 59.206402@5] sdio: rx_tuning_result[0] = 10
[ 59.211073@5] sdio: rx_tuning_result[1] = 10
[ 59.215625@5] sdio: rx_tuning_result[2] = 10
[ 59.220061@5] sdio: rx_tuning_result[3] = 10
[ 59.224144@0] sdio: best_win_start =0, best_win_size =4
[ 59.227892@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 59.235273@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 59.241449@0] sdioh_start: set sd_f2_blocksize 128
[ 59.246526@0]
[ 59.246526@0]
[ 59.246526@0] dhd_bus_devreset: == WLAN ON ==
[ 59.258281@0] F1 signature read @0x18000000=0x15264345
[ 59.267146@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 59.272117@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 59.278805@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 59.283799@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 59.291700@0] dhd_conf_read_config: PM = 0
[ 59.295651@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 59.304417@0] dhdsdio_download_firmware: set use_rxchain 0
[ 59.309825@0] dhdsdio_download_firmware: set txglomsize 40
[ 59.315267@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 59.320787@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 59.326973@0] Final nv_path=/lib/firmware/brcm/
[ 59.331476@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 59.338661@7] usb 1-1.3: new low-speed USB device number 5 using xhci-hcd
[ 59.394139@0] dhdsdio_download_nvram: error reading nvram file: -21
[ 59.398335@0] _dhdsdio_download_firmware: dongle nvram file download failed
[ 59.405256@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 59.410561@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 59.416606@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 59.422050@0] wifi_platform_set_power = 0
[ 59.425902@0] ======== PULL WL_REG_ON LOW! ========
[ 59.430744@0] wl_android_wifi_on: Failed
[ 59.434631@0] dhd_open : wl_android_wifi_on failed (-35)
[ 59.439899@0] dhd_stop: Enter ffffffc052f22000
[ 59.444280@0] wl_android_wifi_off in 1
[ 59.448007@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 59.452855@0] wl_android_wifi_off out
[ 59.456522@0] dhd_stop: Exit
[ 59.460110@0] dhd_open: Exit ret=-1
[ 59.460124@6] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c05a
[ 59.460130@6] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 59.460134@6] usb 1-1.3: Product: USB Optical Mouse
[ 59.460138@6] usb 1-1.3: Manufacturer: Logitech
[ 59.460511@6] usb 1-1.3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 59.496095@0] dhd_open: Enter ffffffc052f22000
[ 59.500234@0]
[ 59.500234@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 59.500234@0] Compiled in drivers/net/wireless/bcmdhd
[ 59.521273@0] wl_android_wifi_on in 1
[ 59.522236@5] input: Logitech USB Optical Mouse as /devices/c9000000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C05A.0004/input/input6
[ 59.522646@5] hid-generic 0003:046D:C05A.0004: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-xhci-hcd.0.auto-1.3/input0
[ 59.522943@7] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 59.522957@7] platform thermal: Driver aml-thermal requests probe deferral
[ 59.566218@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 59.570958@0] wifi_platform_set_power = 1
[ 59.575630@0] ======== PULL WL_REG_ON HIGH! ========
[ 59.580351@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 59.786684@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 60.298577@0] sdio_reset_comm():
[ 60.331379@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 60.339569@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 60.445990@4] sdio: clk 200000000 SDR mode tuning start
[ 60.451605@4] sdio: rx_tuning_result[0] = 10
[ 60.457190@4] sdio: rx_tuning_result[1] = 10
[ 60.462711@7] sdio: rx_tuning_result[2] = 10
[ 60.468161@1] sdio: rx_tuning_result[3] = 10
[ 60.472502@1] sdio: best_win_start =0, best_win_size =4
[ 60.476739@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 60.483649@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 60.489851@1] sdioh_start: set sd_f2_blocksize 128
[ 60.494903@1]
[ 60.494903@1]
[ 60.494903@1] dhd_bus_devreset: == WLAN ON ==
[ 60.509142@1] F1 signature read @0x18000000=0x15264345
[ 60.517726@1] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 60.523583@1] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 60.530228@1] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 60.535189@1] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 60.543121@1] dhd_conf_read_config: PM = 0
[ 60.547345@1] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 60.555832@1] dhdsdio_download_firmware: set use_rxchain 0
[ 60.561249@1] dhdsdio_download_firmware: set txglomsize 40
[ 60.566670@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 60.572201@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 60.578398@1] Final nv_path=/lib/firmware/brcm/
[ 60.582907@1] Final conf_path=/lib/firmware/brcm/config.txt
[ 60.643942@1] dhdsdio_download_nvram: error reading nvram file: -21
[ 60.649075@1] _dhdsdio_download_firmware: dongle nvram file download failed
[ 60.655988@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 60.661315@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 60.667332@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 60.672773@1] wifi_platform_set_power = 0
[ 60.677165@1] ======== PULL WL_REG_ON LOW! ========
[ 60.681584@1] wl_android_wifi_on: Failed
[ 60.685807@1] dhd_open : wl_android_wifi_on failed (-35)
[ 60.690634@1] dhd_stop: Enter ffffffc052f22000
[ 60.695018@1] wl_android_wifi_off in 1
[ 60.698876@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 60.703556@1] wl_android_wifi_off out
[ 60.707269@1] dhd_stop: Exit
[ 60.710957@1] dhd_open: Exit ret=-1
[ 60.717565@1] dhd_open: Enter ffffffc052f22000
[ 60.721317@1]
[ 60.721317@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 60.721317@1] Compiled in drivers/net/wireless/bcmdhd
[ 60.738932@1] wl_android_wifi_on in 1
[ 60.742557@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 60.747250@1] wifi_platform_set_power = 1
[ 60.751238@1] ======== PULL WL_REG_ON HIGH! ========
[ 60.756154@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 60.963065@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 61.478570@1] sdio_reset_comm():
[ 61.613700@7] sdio: clk 200000000 SDR mode tuning start
[ 61.618512@7] sdio: rx_tuning_result[0] = 10
[ 61.623268@7] sdio: rx_tuning_result[1] = 10
[ 61.627937@7] sdio: rx_tuning_result[2] = 10
[ 61.632639@7] sdio: rx_tuning_result[3] = 10
[ 61.637058@2] sdio: best_win_start =0, best_win_size =4
[ 61.640828@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 61.648135@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 61.654338@2] sdioh_start: set sd_f2_blocksize 128
[ 61.659434@2]
[ 61.659434@2]
[ 61.659434@2] dhd_bus_devreset: == WLAN ON ==
[ 61.671996@2] F1 signature read @0x18000000=0x15264345
[ 61.680533@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 61.685643@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 61.692368@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 61.697339@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 61.705269@2] dhd_conf_read_config: PM = 0
[ 61.709239@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 61.717953@2] dhdsdio_download_firmware: set use_rxchain 0
[ 61.723397@2] dhdsdio_download_firmware: set txglomsize 40
[ 61.728833@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 61.734338@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 61.740560@2] Final nv_path=/lib/firmware/brcm/
[ 61.745033@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 61.805093@2] dhdsdio_download_nvram: error reading nvram file: -21
[ 61.809302@2] _dhdsdio_download_firmware: dongle nvram file download failed
[ 61.816214@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 61.821542@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 61.827559@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 61.832987@2] wifi_platform_set_power = 0
[ 61.836873@2] ======== PULL WL_REG_ON LOW! ========
[ 61.841717@2] wl_android_wifi_on: Failed
[ 61.845585@2] dhd_open : wl_android_wifi_on failed (-35)
[ 61.850861@2] dhd_stop: Enter ffffffc052f22000
[ 61.855244@2] wl_android_wifi_off in 1
[ 61.859044@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 61.863782@2] wl_android_wifi_off out
[ 61.867474@2] dhd_stop: Exit
[ 61.871179@2] dhd_open: Exit ret=-1
[ 61.875445@2] dhd_open: Enter ffffffc052f22000
[ 61.879200@2]
[ 61.879200@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 61.879200@2] Compiled in drivers/net/wireless/bcmdhd
[ 61.896850@2] wl_android_wifi_on in 1
[ 61.900480@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 61.905201@2] wifi_platform_set_power = 1
[ 61.909186@2] ======== PULL WL_REG_ON HIGH! ========
[ 61.914103@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 62.121017@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 62.628570@2] sdio_reset_comm():
[ 62.763925@7] sdio: clk 200000000 SDR mode tuning start
[ 62.768737@4] sdio: rx_tuning_result[0] = 10
[ 62.773459@4] sdio: rx_tuning_result[1] = 10
[ 62.778085@4] sdio: rx_tuning_result[2] = 10
[ 62.782774@7] sdio: rx_tuning_result[3] = 10
[ 62.787186@3] sdio: best_win_start =0, best_win_size =4
[ 62.790967@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 62.798261@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 62.804476@3] sdioh_start: set sd_f2_blocksize 128
[ 62.809555@3]
[ 62.809555@3]
[ 62.809555@3] dhd_bus_devreset: == WLAN ON ==
[ 62.822120@3] F1 signature read @0x18000000=0x15264345
[ 62.830596@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 62.835709@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 62.842432@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 62.847405@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 62.855353@3] dhd_conf_read_config: PM = 0
[ 62.859319@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 62.868019@3] dhdsdio_download_firmware: set use_rxchain 0
[ 62.873476@3] dhdsdio_download_firmware: set txglomsize 40
[ 62.878913@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 62.884404@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 62.890640@3] Final nv_path=/lib/firmware/brcm/
[ 62.895099@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 62.953512@3] dhdsdio_download_nvram: error reading nvram file: -21
[ 62.957715@3] _dhdsdio_download_firmware: dongle nvram file download failed
[ 62.964677@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 62.969998@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 62.975994@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 62.981427@3] wifi_platform_set_power = 0
[ 62.985308@3] ======== PULL WL_REG_ON LOW! ========
[ 62.990164@3] wl_android_wifi_on: Failed
[ 62.994021@3] dhd_open : wl_android_wifi_on failed (-35)
[ 62.999308@3] dhd_stop: Enter ffffffc052f22000
[ 63.003680@3] wl_android_wifi_off in 1
[ 63.007475@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 63.012243@3] wl_android_wifi_off out
[ 63.015964@3] dhd_stop: Exit
[ 63.019702@3] dhd_open: Exit ret=-1
[ 63.026408@3] dhd_open: Enter ffffffc052f22000
[ 63.030223@3]
[ 63.030223@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 63.030223@3] Compiled in drivers/net/wireless/bcmdhd
[ 63.047973@3] wl_android_wifi_on in 1
[ 63.052201@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 63.056404@3] wifi_platform_set_power = 1
[ 63.060676@3] ======== PULL WL_REG_ON HIGH! ========
[ 63.065186@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 63.272120@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 63.778575@3] sdio_reset_comm():
[ 63.810500@7] sdio_read_cis: 10 callbacks suppressed
[ 63.815027@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 63.822591@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 63.829681@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 63.838925@0] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 63.936247@5] sdio: clk 200000000 SDR mode tuning start
[ 63.940994@7] sdio: rx_tuning_result[0] = 10
[ 63.945624@7] sdio: rx_tuning_result[1] = 10
[ 63.950120@7] sdio: rx_tuning_result[2] = 10
[ 63.955195@1] sdio: rx_tuning_result[3] = 10
[ 63.959113@1] sdio: best_win_start =0, best_win_size =4
[ 63.962950@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 63.970245@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 63.976417@1] sdioh_start: set sd_f2_blocksize 128
[ 63.981520@1]
[ 63.981520@1]
[ 63.981520@1] dhd_bus_devreset: == WLAN ON ==
[ 63.993200@1] F1 signature read @0x18000000=0x15264345
[ 64.001686@1] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 64.007071@1] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 64.013798@1] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 64.018782@1] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 64.026683@1] dhd_conf_read_config: PM = 0
[ 64.030678@1] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 64.039407@1] dhdsdio_download_firmware: set use_rxchain 0
[ 64.044812@1] dhdsdio_download_firmware: set txglomsize 40
[ 64.050260@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 64.055766@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 64.061988@1] Final nv_path=/lib/firmware/brcm/
[ 64.066461@1] Final conf_path=/lib/firmware/brcm/config.txt
[ 64.126291@1] dhdsdio_download_nvram: error reading nvram file: -21
[ 64.130431@1] _dhdsdio_download_firmware: dongle nvram file download failed
[ 64.137329@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 64.142650@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 64.148680@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 64.154077@1] wifi_platform_set_power = 0
[ 64.157980@1] ======== PULL WL_REG_ON LOW! ========
[ 64.162840@1] wl_android_wifi_on: Failed
[ 64.166693@1] dhd_open : wl_android_wifi_on failed (-35)
[ 64.171969@1] dhd_stop: Enter ffffffc052f22000
[ 64.176352@1] wl_android_wifi_off in 1
[ 64.180073@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 64.184890@1] wl_android_wifi_off out
[ 64.188512@1] dhd_stop: Exit
[ 64.192027@1] dhd_open: Exit ret=-1
[ 64.196105@1] dhd_open: Enter ffffffc052f22000
[ 64.199634@1]
[ 64.199634@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 64.199634@1] Compiled in drivers/net/wireless/bcmdhd
[ 64.217115@1] wl_android_wifi_on in 1
[ 64.220774@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 64.225456@1] wifi_platform_set_power = 1
[ 64.229436@1] ======== PULL WL_REG_ON HIGH! ========
[ 64.234358@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 64.441269@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 64.948567@1] sdio_reset_comm():
[ 64.980494@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 64.987659@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 64.994750@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 65.003869@7] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 65.101839@7] sdio: clk 200000000 SDR mode tuning start
[ 65.106523@7] sdio: rx_tuning_result[0] = 10
[ 65.111155@7] sdio: rx_tuning_result[1] = 10
[ 65.115697@7] sdio: rx_tuning_result[2] = 10
[ 65.120115@7] sdio: rx_tuning_result[3] = 10
[ 65.124192@2] sdio: best_win_start =0, best_win_size =4
[ 65.127932@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 65.135293@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 65.141471@2] sdioh_start: set sd_f2_blocksize 128
[ 65.146539@2]
[ 65.146539@2]
[ 65.146539@2] dhd_bus_devreset: == WLAN ON ==
[ 65.158221@2] F1 signature read @0x18000000=0x15264345
[ 65.166904@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 65.171900@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 65.178578@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 65.183573@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 65.191502@2] dhd_conf_read_config: PM = 0
[ 65.195459@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 65.204221@2] dhdsdio_download_firmware: set use_rxchain 0
[ 65.209632@2] dhdsdio_download_firmware: set txglomsize 40
[ 65.215053@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 65.220584@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 65.226782@2] Final nv_path=/lib/firmware/brcm/
[ 65.231279@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 65.291670@2] dhdsdio_download_nvram: error reading nvram file: -21
[ 65.295728@2] _dhdsdio_download_firmware: dongle nvram file download failed
[ 65.302687@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 65.307973@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 65.314023@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 65.319438@2] wifi_platform_set_power = 0
[ 65.323321@2] ======== PULL WL_REG_ON LOW! ========
[ 65.328151@2] wl_android_wifi_on: Failed
[ 65.332047@2] dhd_open : wl_android_wifi_on failed (-35)
[ 65.337297@2] dhd_stop: Enter ffffffc052f22000
[ 65.341706@2] wl_android_wifi_off in 1
[ 65.345402@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 65.350243@2] wl_android_wifi_off out
[ 65.353854@2] dhd_stop: Exit
[ 65.357376@2] dhd_open: Exit ret=-1
[ 65.363832@2] dhd_open: Enter ffffffc052f22000
[ 65.367334@2]
[ 65.367334@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 65.367334@2] Compiled in drivers/net/wireless/bcmdhd
[ 65.384795@2] wl_android_wifi_on in 1
[ 65.388416@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 65.393140@2] wifi_platform_set_power = 1
[ 65.397092@2] ======== PULL WL_REG_ON HIGH! ========
[ 65.402074@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 65.608942@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 66.118572@2] sdio_reset_comm():
[ 66.150482@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 66.157644@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 66.262794@5] sdio: clk 200000000 SDR mode tuning start
[ 66.267503@5] sdio: rx_tuning_result[0] = 10
[ 66.272271@4] sdio: rx_tuning_result[1] = 10
[ 66.276989@4] sdio: rx_tuning_result[2] = 10
[ 66.281629@4] sdio: rx_tuning_result[3] = 10
[ 66.285959@3] sdio: best_win_start =0, best_win_size =4
[ 66.289742@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 66.297036@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 66.303247@3] sdioh_start: set sd_f2_blocksize 128
[ 66.308306@3]
[ 66.308306@3]
[ 66.308306@3] dhd_bus_devreset: == WLAN ON ==
[ 66.322057@3] F1 signature read @0x18000000=0x15264345
[ 66.330765@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 66.335852@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 66.342561@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 66.347485@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 66.355451@0] dhd_conf_read_config: PM = 0
[ 66.359385@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 66.368122@0] dhdsdio_download_firmware: set use_rxchain 0
[ 66.373549@0] dhdsdio_download_firmware: set txglomsize 40
[ 66.378978@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 66.384506@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 66.390710@0] Final nv_path=/lib/firmware/brcm/
[ 66.395179@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 66.457963@0] dhdsdio_download_nvram: error reading nvram file: -21
[ 66.462140@0] _dhdsdio_download_firmware: dongle nvram file download failed
[ 66.469107@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 66.474359@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 66.480411@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 66.485833@0] wifi_platform_set_power = 0
[ 66.489727@0] ======== PULL WL_REG_ON LOW! ========
[ 66.494539@0] wl_android_wifi_on: Failed
[ 66.498442@0] dhd_open : wl_android_wifi_on failed (-35)
[ 66.503702@0] dhd_stop: Enter ffffffc052f22000
[ 66.508080@0] wl_android_wifi_off in 1
[ 66.511844@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 66.516639@0] wl_android_wifi_off out
[ 66.520369@0] dhd_stop: Exit
[ 66.524044@0] dhd_open: Exit ret=-1
[ 66.528256@0] dhd_open: Enter ffffffc052f22000
[ 66.532023@0]
[ 66.532023@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 66.532023@0] Compiled in drivers/net/wireless/bcmdhd
[ 66.549624@0] wl_android_wifi_on in 1
[ 66.553247@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 66.557950@0] wifi_platform_set_power = 1
[ 66.561943@0] ======== PULL WL_REG_ON HIGH! ========
[ 66.566875@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 66.773767@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 67.288577@0] sdio_reset_comm():
[ 67.424121@7] sdio: clk 200000000 SDR mode tuning start
[ 67.428960@7] sdio: rx_tuning_result[0] = 10
[ 67.433707@7] sdio: rx_tuning_result[1] = 10
[ 67.438354@7] sdio: rx_tuning_result[2] = 10
[ 67.443038@7] sdio: rx_tuning_result[3] = 10
[ 67.447470@0] sdio: best_win_start =0, best_win_size =4
[ 67.451253@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 67.458541@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 67.464766@0] sdioh_start: set sd_f2_blocksize 128
[ 67.469918@0]
[ 67.469918@0]
[ 67.469918@0] dhd_bus_devreset: == WLAN ON ==
[ 67.482526@0] F1 signature read @0x18000000=0x15264345
[ 67.491180@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 67.496325@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 67.503072@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 67.507995@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 67.515956@0] dhd_conf_read_config: PM = 0
[ 67.519897@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 67.528626@0] dhdsdio_download_firmware: set use_rxchain 0
[ 67.534066@0] dhdsdio_download_firmware: set txglomsize 40
[ 67.539494@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 67.544994@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 67.551239@0] Final nv_path=/lib/firmware/brcm/
[ 67.555689@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 67.616567@1] dhdsdio_download_nvram: error reading nvram file: -21
[ 67.620792@1] _dhdsdio_download_firmware: dongle nvram file download failed
[ 67.627702@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 67.633032@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 67.639081@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 67.644456@1] wifi_platform_set_power = 0
[ 67.648362@1] ======== PULL WL_REG_ON LOW! ========
[ 67.653212@1] wl_android_wifi_on: Failed
[ 67.657076@1] dhd_open : wl_android_wifi_on failed (-35)
[ 67.662351@1] dhd_stop: Enter ffffffc052f22000
[ 67.666735@1] wl_android_wifi_off in 1
[ 67.670544@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 67.675273@1] wl_android_wifi_off out
[ 67.678990@1] dhd_stop: Exit
[ 67.682698@1] dhd_open: Exit ret=-1
[ 67.689418@1] dhd_open: Enter ffffffc052f22000
[ 67.693164@1]
[ 67.693164@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 67.693164@1] Compiled in drivers/net/wireless/bcmdhd
[ 67.710862@1] wl_android_wifi_on in 1
[ 67.715071@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 67.719277@1] wifi_platform_set_power = 1
[ 67.723520@1] ======== PULL WL_REG_ON HIGH! ========
[ 67.728077@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 67.935003@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 68.448572@1] sdio_reset_comm():
[ 68.583734@5] sdio: clk 200000000 SDR mode tuning start
[ 68.588530@5] sdio: rx_tuning_result[0] = 10
[ 68.593257@5] sdio: rx_tuning_result[1] = 10
[ 68.597922@5] sdio: rx_tuning_result[2] = 10
[ 68.602600@5] sdio: rx_tuning_result[3] = 10
[ 68.607012@1] sdio: best_win_start =0, best_win_size =4
[ 68.610787@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 68.618083@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 68.624285@1] sdioh_start: set sd_f2_blocksize 128
[ 68.629375@1]
[ 68.629375@1]
[ 68.629375@1] dhd_bus_devreset: == WLAN ON ==
[ 68.641913@1] F1 signature read @0x18000000=0x15264345
[ 68.650477@1] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 68.656086@1] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 68.662779@1] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 68.667779@1] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 68.675727@1] dhd_conf_read_config: PM = 0
[ 68.679680@1] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 68.688394@1] dhdsdio_download_firmware: set use_rxchain 0
[ 68.693845@1] dhdsdio_download_firmware: set txglomsize 40
[ 68.699287@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 68.704778@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 68.711002@1] Final nv_path=/lib/firmware/brcm/
[ 68.715474@1] Final conf_path=/lib/firmware/brcm/config.txt
[ 68.775246@1] dhdsdio_download_nvram: error reading nvram file: -21
[ 68.779466@1] _dhdsdio_download_firmware: dongle nvram file download failed
[ 68.786384@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 68.791721@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 68.797723@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 68.803145@1] wifi_platform_set_power = 0
[ 68.807037@1] ======== PULL WL_REG_ON LOW! ========
[ 68.811881@1] wl_android_wifi_on: Failed
[ 68.815749@1] dhd_open : wl_android_wifi_on failed (-35)
[ 68.821038@1] dhd_stop: Enter ffffffc052f22000
[ 68.825408@1] wl_android_wifi_off in 1
[ 68.829202@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 68.833946@1] wl_android_wifi_off out
[ 68.837642@1] dhd_stop: Exit
[ 68.841362@1] dhd_open: Exit ret=-1
[ 68.845635@1] dhd_open: Enter ffffffc052f22000
[ 68.849402@1]
[ 68.849402@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 68.849402@1] Compiled in drivers/net/wireless/bcmdhd
[ 68.867050@1] wl_android_wifi_on in 1
[ 68.870680@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 68.875399@1] wifi_platform_set_power = 1
[ 68.879392@1] ======== PULL WL_REG_ON HIGH! ========
[ 68.884302@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 69.091214@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 69.598582@1] sdio_reset_comm():
[ 69.630532@4] sdio_read_cis: 10 callbacks suppressed
[ 69.635038@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 69.642606@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 69.649677@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 69.658894@2] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 69.756470@7] sdio: clk 200000000 SDR mode tuning start
[ 69.761344@7] sdio: rx_tuning_result[0] = 10
[ 69.765951@7] sdio: rx_tuning_result[1] = 10
[ 69.770435@4] sdio: rx_tuning_result[2] = 10
[ 69.774841@3] sdio: rx_tuning_result[3] = 10
[ 69.778209@3] sdio: best_win_start =0, best_win_size =4
[ 69.782590@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 69.789917@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 69.796072@3] sdioh_start: set sd_f2_blocksize 128
[ 69.801160@3]
[ 69.801160@3]
[ 69.801160@3] dhd_bus_devreset: == WLAN ON ==
[ 69.812827@3] F1 signature read @0x18000000=0x15264345
[ 69.821367@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 69.826258@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 69.832950@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 69.837942@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 69.845885@3] dhd_conf_read_config: PM = 0
[ 69.849856@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 69.858583@3] dhdsdio_download_firmware: set use_rxchain 0
[ 69.863988@3] dhdsdio_download_firmware: set txglomsize 40
[ 69.869445@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 69.874941@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 69.881178@3] Final nv_path=/lib/firmware/brcm/
[ 69.885636@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 69.944563@3] dhdsdio_download_nvram: error reading nvram file: -21
[ 69.948695@3] _dhdsdio_download_firmware: dongle nvram file download failed
[ 69.955596@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 69.960930@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 69.966937@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 69.972372@3] wifi_platform_set_power = 0
[ 69.976250@3] ======== PULL WL_REG_ON LOW! ========
[ 69.981107@3] wl_android_wifi_on: Failed
[ 69.984963@3] dhd_open : wl_android_wifi_on failed (-35)
[ 69.990250@3] dhd_stop: Enter ffffffc052f22000
[ 69.994622@3] wl_android_wifi_off in 1
[ 69.998330@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 70.003184@3] wl_android_wifi_off out
[ 70.006784@3] dhd_stop: Exit
[ 70.010306@3] dhd_open: Exit ret=-1
[ 70.016796@3] dhd_open: Enter ffffffc052f22000
[ 70.020376@3]
[ 70.020376@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 70.020376@3] Compiled in drivers/net/wireless/bcmdhd
[ 70.037903@3] wl_android_wifi_on in 1
[ 70.041556@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 70.046226@3] wifi_platform_set_power = 1
[ 70.050219@3] ======== PULL WL_REG_ON HIGH! ========
[ 70.055129@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 70.262055@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 70.768582@3] sdio_reset_comm():
[ 70.800548@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 70.807720@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 70.814814@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 70.823947@7] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 70.921716@4] sdio: clk 200000000 SDR mode tuning start
[ 70.926393@4] sdio: rx_tuning_result[0] = 10
[ 70.931023@4] sdio: rx_tuning_result[1] = 10
[ 70.935568@4] sdio: rx_tuning_result[2] = 10
[ 70.939986@4] sdio: rx_tuning_result[3] = 10
[ 70.944074@0] sdio: best_win_start =0, best_win_size =4
[ 70.947818@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 70.955234@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 70.961375@0] sdioh_start: set sd_f2_blocksize 128
[ 70.966479@0]
[ 70.966479@0]
[ 70.966479@0] dhd_bus_devreset: == WLAN ON ==
[ 70.978189@0] F1 signature read @0x18000000=0x15264345
[ 70.986986@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 70.991971@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 70.998652@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 71.003596@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 71.011527@0] dhd_conf_read_config: PM = 0
[ 71.015509@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 71.024226@0] dhdsdio_download_firmware: set use_rxchain 0
[ 71.029656@0] dhdsdio_download_firmware: set txglomsize 40
[ 71.035098@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 71.040611@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 71.046805@0] Final nv_path=/lib/firmware/brcm/
[ 71.051324@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 71.113840@0] dhdsdio_download_nvram: error reading nvram file: -21
[ 71.117943@0] _dhdsdio_download_firmware: dongle nvram file download failed
[ 71.124957@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 71.130183@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 71.136221@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 71.141617@0] wifi_platform_set_power = 0
[ 71.145501@0] ======== PULL WL_REG_ON LOW! ========
[ 71.150374@0] wl_android_wifi_on: Failed
[ 71.154213@0] dhd_open : wl_android_wifi_on failed (-35)
[ 71.159493@0] dhd_stop: Enter ffffffc052f22000
[ 71.163872@0] wl_android_wifi_off in 1
[ 71.167602@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 71.172428@0] wl_android_wifi_off out
[ 71.176033@0] dhd_stop: Exit
[ 71.179585@0] dhd_open: Exit ret=-1
[ 71.183691@0] dhd_open: Enter ffffffc052f22000
[ 71.187203@0]
[ 71.187203@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 71.187203@0] Compiled in drivers/net/wireless/bcmdhd
[ 71.204733@0] wl_android_wifi_on in 1
[ 71.208350@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 71.213056@0] wifi_platform_set_power = 1
[ 71.217016@0] ======== PULL WL_REG_ON HIGH! ========
[ 71.221953@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 71.428853@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 71.938575@0] sdio_reset_comm():
[ 71.970483@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 71.977643@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 72.082904@4] sdio: clk 200000000 SDR mode tuning start
[ 72.087618@4] sdio: rx_tuning_result[0] = 10
[ 72.092368@4] sdio: rx_tuning_result[1] = 10
[ 72.097086@4] sdio: rx_tuning_result[2] = 10
[ 72.101714@4] sdio: rx_tuning_result[3] = 10
[ 72.106056@0] sdio: best_win_start =0, best_win_size =4
[ 72.109842@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 72.117151@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 72.123358@0] sdioh_start: set sd_f2_blocksize 128
[ 72.128443@0]
[ 72.128443@0]
[ 72.128443@0] dhd_bus_devreset: == WLAN ON ==
[ 72.140589@0] F1 signature read @0x18000000=0x15264345
[ 72.149240@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 72.154289@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 72.160988@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 72.165987@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 72.173888@0] dhd_conf_read_config: PM = 0
[ 72.177839@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 72.186604@0] dhdsdio_download_firmware: set use_rxchain 0
[ 72.192013@0] dhdsdio_download_firmware: set txglomsize 40
[ 72.197432@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 72.202986@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 72.209175@0] Final nv_path=/lib/firmware/brcm/
[ 72.213646@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 72.277003@0] dhdsdio_download_nvram: error reading nvram file: -21
[ 72.281166@0] _dhdsdio_download_firmware: dongle nvram file download failed
[ 72.288128@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 72.293406@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 72.299463@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 72.304838@0] wifi_platform_set_power = 0
[ 72.308754@0] ======== PULL WL_REG_ON LOW! ========
[ 72.313568@0] wl_android_wifi_on: Failed
[ 72.317472@0] dhd_open : wl_android_wifi_on failed (-35)
[ 72.322730@0] dhd_stop: Enter ffffffc052f22000
[ 72.327109@0] wl_android_wifi_off in 1
[ 72.330857@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 72.335668@0] wl_android_wifi_off out
[ 72.339383@0] dhd_stop: Exit
[ 72.343046@0] dhd_open: Exit ret=-1
[ 72.349703@0] dhd_open: Enter ffffffc052f22000
[ 72.353387@0]
[ 72.353387@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 72.353387@0] Compiled in drivers/net/wireless/bcmdhd
[ 72.371007@0] wl_android_wifi_on in 1
[ 72.374630@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 72.379304@0] wifi_platform_set_power = 1
[ 72.383271@0] ======== PULL WL_REG_ON HIGH! ========
[ 72.388185@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 72.595122@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 73.108583@2] sdio_reset_comm():
[ 73.243783@4] sdio: clk 200000000 SDR mode tuning start
[ 73.248602@7] sdio: rx_tuning_result[0] = 10
[ 73.253367@4] sdio: rx_tuning_result[1] = 10
[ 73.258028@4] sdio: rx_tuning_result[2] = 10
[ 73.262745@4] sdio: rx_tuning_result[3] = 10
[ 73.267151@1] sdio: best_win_start =0, best_win_size =4
[ 73.270928@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 73.278236@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 73.284437@1] sdioh_start: set sd_f2_blocksize 128
[ 73.289553@1]
[ 73.289553@1]
[ 73.289553@1] dhd_bus_devreset: == WLAN ON ==
[ 73.302130@1] F1 signature read @0x18000000=0x15264345
[ 73.310635@1] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 73.315761@1] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 73.322482@1] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 73.327453@1] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 73.335392@1] dhd_conf_read_config: PM = 0
[ 73.339354@1] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 73.348067@1] dhdsdio_download_firmware: set use_rxchain 0
[ 73.353531@1] dhdsdio_download_firmware: set txglomsize 40
[ 73.358947@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 73.364452@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 73.370674@1] Final nv_path=/lib/firmware/brcm/
[ 73.375147@1] Final conf_path=/lib/firmware/brcm/config.txt
[ 73.435104@1] dhdsdio_download_nvram: error reading nvram file: -21
[ 73.439349@1] _dhdsdio_download_firmware: dongle nvram file download failed
[ 73.446247@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 73.451569@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 73.457586@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 73.463005@1] wifi_platform_set_power = 0
[ 73.466900@1] ======== PULL WL_REG_ON LOW! ========
[ 73.471757@1] wl_android_wifi_on: Failed
[ 73.475613@1] dhd_open : wl_android_wifi_on failed (-35)
[ 73.480888@1] dhd_stop: Enter ffffffc052f22000
[ 73.485271@1] wl_android_wifi_off in 1
[ 73.489074@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 73.493810@1] wl_android_wifi_off out
[ 73.497518@1] dhd_stop: Exit
[ 73.501248@1] dhd_open: Exit ret=-1
[ 73.505542@1] dhd_open: Enter ffffffc052f22000
[ 73.509856@1]
[ 73.509856@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 73.509856@1] Compiled in drivers/net/wireless/bcmdhd
[ 73.529360@1] wl_android_wifi_on in 1
[ 73.532974@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 73.537668@1] wifi_platform_set_power = 1
[ 73.541661@1] ======== PULL WL_REG_ON HIGH! ========
[ 73.546572@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 73.753484@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 74.258566@1] sdio_reset_comm():
[ 74.393779@4] sdio: clk 200000000 SDR mode tuning start
[ 74.398578@7] sdio: rx_tuning_result[0] = 10
[ 74.398841@7] sdio: rx_tuning_result[1] = 10
[ 74.399105@4] sdio: rx_tuning_result[2] = 10
[ 74.399362@4] sdio: rx_tuning_result[3] = 10
[ 74.399391@4] sdio: best_win_start =0, best_win_size =4
[ 74.399394@4] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 74.399399@4] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 74.399454@4] sdioh_start: set sd_f2_blocksize 128
[ 74.399827@4]
[ 74.399827@4]
[ 74.399827@4] dhd_bus_devreset: == WLAN ON ==
[ 74.400008@4] F1 signature read @0x18000000=0x15264345
[ 74.403341@4] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 74.404020@4] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 74.404438@4] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 74.404442@4] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 74.404629@4] dhd_conf_read_config: PM = 0
[ 74.404712@4] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 74.404716@4] dhdsdio_download_firmware: set use_rxchain 0
[ 74.404717@4] dhdsdio_download_firmware: set txglomsize 40
[ 74.404720@4] sdioh_set_mode: set txglom_mode to multi-desc
[ 74.404722@4] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 74.404723@4] Final nv_path=/lib/firmware/brcm/
[ 74.404725@4] Final conf_path=/lib/firmware/brcm/config.txt
[ 74.454970@4] dhdsdio_download_nvram: error reading nvram file: -21
[ 74.454978@4] _dhdsdio_download_firmware: dongle nvram file download failed
[ 74.455013@4] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 74.455018@4] dhd_prot_ioctl : bus is down. we have nothing to do
[ 74.455021@4] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 74.455074@4] wifi_platform_set_power = 0
[ 74.455076@4] ======== PULL WL_REG_ON LOW! ========
[ 74.455078@4] wl_android_wifi_on: Failed
[ 74.455081@4] dhd_open : wl_android_wifi_on failed (-35)
[ 74.455086@4] dhd_stop: Enter ffffffc052f22000
[ 74.455088@4] wl_android_wifi_off in 1
[ 74.455090@4] wl_android_wifi_off in 2: g_wifi_on=0
[ 74.455091@4] wl_android_wifi_off out
[ 74.455093@4] dhd_stop: Exit
[ 74.455097@4] dhd_open: Exit ret=-1
[ 74.459207@4] dhd_open: Enter ffffffc052f22000
[ 74.459215@4]
[ 74.459215@4] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 74.459215@4] Compiled in drivers/net/wireless/bcmdhd
[ 74.459217@4] wl_android_wifi_on in 1
[ 74.459220@4] wl_android_wifi_on in 2: g_wifi_on=0
[ 74.459223@4] wifi_platform_set_power = 1
[ 74.459225@4] ======== PULL WL_REG_ON HIGH! ========
[ 74.459248@4] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 74.659284@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 75.168580@3] sdio_reset_comm():
[ 75.200385@4] sdio_read_cis: 10 callbacks suppressed
[ 75.204720@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 75.212333@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 75.219239@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 75.228290@0] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 75.325644@5] sdio: clk 200000000 SDR mode tuning start
[ 75.330165@5] sdio: rx_tuning_result[0] = 10
[ 75.334610@5] sdio: rx_tuning_result[1] = 10
[ 75.338920@5] sdio: rx_tuning_result[2] = 10
[ 75.343103@5] sdio: rx_tuning_result[3] = 10
[ 75.346967@1] sdio: best_win_start =0, best_win_size =4
[ 75.351531@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 75.358864@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 75.365053@1] sdioh_start: set sd_f2_blocksize 128
[ 75.370133@1]
[ 75.370133@1]
[ 75.370133@1] dhd_bus_devreset: == WLAN ON ==
[ 75.381436@1] F1 signature read @0x18000000=0x15264345
[ 75.389961@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 75.394783@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 75.401519@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 75.406474@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 75.414407@2] dhd_conf_read_config: PM = 0
[ 75.418361@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 75.427103@2] dhdsdio_download_firmware: set use_rxchain 0
[ 75.432534@2] dhdsdio_download_firmware: set txglomsize 40
[ 75.437955@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 75.443486@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 75.449696@2] Final nv_path=/lib/firmware/brcm/
[ 75.454169@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 75.514749@2] dhdsdio_download_nvram: error reading nvram file: -21
[ 75.518825@2] _dhdsdio_download_firmware: dongle nvram file download failed
[ 75.525745@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 75.531066@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 75.537083@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 75.542506@2] wifi_platform_set_power = 0
[ 75.546396@2] ======== PULL WL_REG_ON LOW! ========
[ 75.551240@2] wl_android_wifi_on: Failed
[ 75.555109@2] dhd_open : wl_android_wifi_on failed (-35)
[ 75.560384@2] dhd_stop: Enter ffffffc052f22000
[ 75.564768@2] wl_android_wifi_off in 1
[ 75.568476@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 75.573318@2] wl_android_wifi_off out
[ 75.576929@2] dhd_stop: Exit
[ 75.580436@2] dhd_open: Exit ret=-1
[ 75.584519@2] dhd_open: Enter ffffffc052f22000
[ 75.588017@2]
[ 75.588017@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 75.588017@2] Compiled in drivers/net/wireless/bcmdhd
[ 75.605523@2] wl_android_wifi_on in 1
[ 75.609154@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 75.613836@2] wifi_platform_set_power = 1
[ 75.617802@2] ======== PULL WL_REG_ON HIGH! ========
[ 75.622761@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 75.829651@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 76.338573@2] sdio_reset_comm():
[ 76.370512@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 76.377685@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 76.384794@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 76.393929@4] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 76.491679@4] sdio: clk 200000000 SDR mode tuning start
[ 76.496383@4] sdio: rx_tuning_result[0] = 10
[ 76.501080@4] sdio: rx_tuning_result[1] = 10
[ 76.505651@4] sdio: rx_tuning_result[2] = 10
[ 76.510069@4] sdio: rx_tuning_result[3] = 10
[ 76.514151@2] sdio: best_win_start =0, best_win_size =4
[ 76.517892@2] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 76.525249@2] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 76.531428@2] sdioh_start: set sd_f2_blocksize 128
[ 76.536498@2]
[ 76.536498@2]
[ 76.536498@2] dhd_bus_devreset: == WLAN ON ==
[ 76.548216@2] F1 signature read @0x18000000=0x15264345
[ 76.556867@2] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 76.561824@2] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 76.568473@2] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 76.573493@2] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 76.581402@2] dhd_conf_read_config: PM = 0
[ 76.585358@2] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 76.594106@2] dhdsdio_download_firmware: set use_rxchain 0
[ 76.599550@2] dhdsdio_download_firmware: set txglomsize 40
[ 76.604951@2] sdioh_set_mode: set txglom_mode to multi-desc
[ 76.610485@2] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 76.616681@2] Final nv_path=/lib/firmware/brcm/
[ 76.621178@2] Final conf_path=/lib/firmware/brcm/config.txt
[ 76.681827@2] dhdsdio_download_nvram: error reading nvram file: -21
[ 76.685895@2] _dhdsdio_download_firmware: dongle nvram file download failed
[ 76.692846@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 76.698140@2] dhd_prot_ioctl : bus is down. we have nothing to do
[ 76.704189@2] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 76.709604@2] wifi_platform_set_power = 0
[ 76.713488@2] ======== PULL WL_REG_ON LOW! ========
[ 76.718318@2] wl_android_wifi_on: Failed
[ 76.722214@2] dhd_open : wl_android_wifi_on failed (-35)
[ 76.727463@2] dhd_stop: Enter ffffffc052f22000
[ 76.731872@2] wl_android_wifi_off in 1
[ 76.735569@2] wl_android_wifi_off in 2: g_wifi_on=0
[ 76.740410@2] wl_android_wifi_off out
[ 76.744021@2] dhd_stop: Exit
[ 76.747547@2] dhd_open: Exit ret=-1
[ 76.754045@2] dhd_open: Enter ffffffc052f22000
[ 76.757547@2]
[ 76.757547@2] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 76.757547@2] Compiled in drivers/net/wireless/bcmdhd
[ 76.775005@2] wl_android_wifi_on in 1
[ 76.778644@2] wl_android_wifi_on in 2: g_wifi_on=0
[ 76.783333@2] wifi_platform_set_power = 1
[ 76.787300@2] ======== PULL WL_REG_ON HIGH! ========
[ 76.792258@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 76.999179@2] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 77.508573@2] sdio_reset_comm():
[ 77.541116@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 77.548276@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 77.653437@4] sdio: clk 200000000 SDR mode tuning start
[ 77.658146@4] sdio: rx_tuning_result[0] = 10
[ 77.662900@4] sdio: rx_tuning_result[1] = 10
[ 77.667612@4] sdio: rx_tuning_result[2] = 10
[ 77.672243@4] sdio: rx_tuning_result[3] = 10
[ 77.676574@0] sdio: best_win_start =0, best_win_size =4
[ 77.680342@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 77.687668@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 77.693869@0] sdioh_start: set sd_f2_blocksize 128
[ 77.699013@0]
[ 77.699013@0]
[ 77.699013@0] dhd_bus_devreset: == WLAN ON ==
[ 77.711140@0] F1 signature read @0x18000000=0x15264345
[ 77.719803@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 77.724840@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 77.731540@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 77.736544@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 77.744456@0] dhd_conf_read_config: PM = 0
[ 77.748423@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 77.757143@0] dhdsdio_download_firmware: set use_rxchain 0
[ 77.762573@0] dhdsdio_download_firmware: set txglomsize 40
[ 77.768014@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 77.773528@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 77.779735@0] Final nv_path=/lib/firmware/brcm/
[ 77.784227@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 77.847031@0] dhdsdio_download_nvram: error reading nvram file: -21
[ 77.851221@0] _dhdsdio_download_firmware: dongle nvram file download failed
[ 77.858115@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 77.863429@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 77.869488@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 77.874863@0] wifi_platform_set_power = 0
[ 77.879191@0] ======== PULL WL_REG_ON LOW! ========
[ 77.883616@0] wl_android_wifi_on: Failed
[ 77.887954@0] dhd_open : wl_android_wifi_on failed (-35)
[ 77.892755@0] dhd_stop: Enter ffffffc052f22000
[ 77.897144@0] wl_android_wifi_off in 1
[ 77.901524@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 77.905678@0] wl_android_wifi_off out
[ 77.909388@0] dhd_stop: Exit
[ 77.913044@0] dhd_open: Exit ret=-1
[ 77.917260@0] dhd_open: Enter ffffffc052f22000
[ 77.920972@0]
[ 77.920972@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 77.920972@0] Compiled in drivers/net/wireless/bcmdhd
[ 77.938539@0] wl_android_wifi_on in 1
[ 77.942701@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 77.946893@0] wifi_platform_set_power = 1
[ 77.951166@0] ======== PULL WL_REG_ON HIGH! ========
[ 77.955743@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 78.162673@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 78.668573@0] sdio_reset_comm():
[ 78.803834@5] sdio: clk 200000000 SDR mode tuning start
[ 78.808833@7] sdio: rx_tuning_result[0] = 10
[ 78.813554@7] sdio: rx_tuning_result[1] = 10
[ 78.818177@7] sdio: rx_tuning_result[2] = 10
[ 78.822909@5] sdio: rx_tuning_result[3] = 10
[ 78.827319@3] sdio: best_win_start =0, best_win_size =4
[ 78.831107@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 78.838398@3] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 78.844612@3] sdioh_start: set sd_f2_blocksize 128
[ 78.849704@3]
[ 78.849704@3]
[ 78.849704@3] dhd_bus_devreset: == WLAN ON ==
[ 78.862265@3] F1 signature read @0x18000000=0x15264345
[ 78.870782@3] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 78.876417@3] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 78.883125@3] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 78.888094@3] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 78.896040@3] dhd_conf_read_config: PM = 0
[ 78.900005@3] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 78.908736@3] dhdsdio_download_firmware: set use_rxchain 0
[ 78.914140@3] dhdsdio_download_firmware: set txglomsize 40
[ 78.919600@3] sdioh_set_mode: set txglom_mode to multi-desc
[ 78.925093@3] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 78.931326@3] Final nv_path=/lib/firmware/brcm/
[ 78.935788@3] Final conf_path=/lib/firmware/brcm/config.txt
[ 78.995194@3] dhdsdio_download_nvram: error reading nvram file: -21
[ 78.999431@3] _dhdsdio_download_firmware: dongle nvram file download failed
[ 79.006331@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 79.011666@3] dhd_prot_ioctl : bus is down. we have nothing to do
[ 79.017676@3] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 79.023107@3] wifi_platform_set_power = 0
[ 79.026989@3] ======== PULL WL_REG_ON LOW! ========
[ 79.031848@3] wl_android_wifi_on: Failed
[ 79.035702@3] dhd_open : wl_android_wifi_on failed (-35)
[ 79.040991@3] dhd_stop: Enter ffffffc052f22000
[ 79.045361@3] wl_android_wifi_off in 1
[ 79.049170@3] wl_android_wifi_off in 2: g_wifi_on=0
[ 79.053899@3] wl_android_wifi_off out
[ 79.057600@3] dhd_stop: Exit
[ 79.061324@3] dhd_open: Exit ret=-1
[ 79.068026@3] dhd_open: Enter ffffffc052f22000
[ 79.071846@3]
[ 79.071846@3] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 79.071846@3] Compiled in drivers/net/wireless/bcmdhd
[ 79.089551@3] wl_android_wifi_on in 1
[ 79.093164@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 79.097869@3] wifi_platform_set_power = 1
[ 79.101872@3] ======== PULL WL_REG_ON HIGH! ========
[ 79.106774@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 79.313698@3] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 79.828581@3] sdio_reset_comm():
[ 79.963866@7] sdio: clk 200000000 SDR mode tuning start
[ 79.968882@4] sdio: rx_tuning_result[0] = 10
[ 79.973621@4] sdio: rx_tuning_result[1] = 10
[ 79.978256@4] sdio: rx_tuning_result[2] = 10
[ 79.983291@4] sdio: rx_tuning_result[3] = 10
[ 79.987724@1] sdio: best_win_start =0, best_win_size =4
[ 79.991497@1] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 79.998825@1] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 80.005000@1] sdioh_start: set sd_f2_blocksize 128
[ 80.010121@1]
[ 80.010121@1]
[ 80.010121@1] dhd_bus_devreset: == WLAN ON ==
[ 80.022694@1] F1 signature read @0x18000000=0x15264345
[ 80.031186@1] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 80.036810@1] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 80.043547@1] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 80.048501@1] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 80.056434@1] dhd_conf_read_config: PM = 0
[ 80.060401@1] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 80.069145@1] dhdsdio_download_firmware: set use_rxchain 0
[ 80.074547@1] dhdsdio_download_firmware: set txglomsize 40
[ 80.079995@1] sdioh_set_mode: set txglom_mode to multi-desc
[ 80.085501@1] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 80.091723@1] Final nv_path=/lib/firmware/brcm/
[ 80.096196@1] Final conf_path=/lib/firmware/brcm/config.txt
[ 80.156209@1] dhdsdio_download_nvram: error reading nvram file: -21
[ 80.160457@1] _dhdsdio_download_firmware: dongle nvram file download failed
[ 80.167350@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 80.172678@1] dhd_prot_ioctl : bus is down. we have nothing to do
[ 80.178708@1] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 80.184102@1] wifi_platform_set_power = 0
[ 80.188008@1] ======== PULL WL_REG_ON LOW! ========
[ 80.192868@1] wl_android_wifi_on: Failed
[ 80.196722@1] dhd_open : wl_android_wifi_on failed (-35)
[ 80.201997@1] dhd_stop: Enter ffffffc052f22000
[ 80.206380@1] wl_android_wifi_off in 1
[ 80.210187@1] wl_android_wifi_off in 2: g_wifi_on=0
[ 80.214918@1] wl_android_wifi_off out
[ 80.218654@1] dhd_stop: Exit
[ 80.222365@1] dhd_open: Exit ret=-1
[ 80.226659@1] dhd_open: Enter ffffffc052f22000
[ 80.230412@1]
[ 80.230412@1] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 80.230412@1] Compiled in drivers/net/wireless/bcmdhd
[ 80.248120@1] wl_android_wifi_on in 1
[ 80.251804@1] wl_android_wifi_on in 2: g_wifi_on=0
[ 80.256458@1] wifi_platform_set_power = 1
[ 80.260439@1] ======== PULL WL_REG_ON HIGH! ========
[ 80.265361@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 80.472281@1] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 80.978565@1] sdio_reset_comm():
[ 81.010501@7] sdio_read_cis: 10 callbacks suppressed
[ 81.015039@7] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 81.022898@7] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 81.030736@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 81.039977@2] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 81.137415@5] sdio: clk 200000000 SDR mode tuning start
[ 81.142123@5] sdio: rx_tuning_result[0] = 10
[ 81.146751@5] sdio: rx_tuning_result[1] = 10
[ 81.151260@5] sdio: rx_tuning_result[2] = 10
[ 81.155734@0] sdio: rx_tuning_result[3] = 10
[ 81.159162@0] sdio: best_win_start =0, best_win_size =4
[ 81.163474@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 81.170846@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x22000
[ 81.177003@0] sdioh_start: set sd_f2_blocksize 128
[ 81.182152@0]
[ 81.182152@0]
[ 81.182152@0] dhd_bus_devreset: == WLAN ON ==
[ 81.193857@0] F1 signature read @0x18000000=0x15264345
[ 81.202690@0] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x6 pkg:0x2
[ 81.207605@0] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[ 81.214311@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=1
[ 81.219335@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
[ 81.227196@0] dhd_conf_read_config: PM = 0
[ 81.231179@0] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 81.239930@0] dhdsdio_download_firmware: set use_rxchain 0
[ 81.245324@0] dhdsdio_download_firmware: set txglomsize 40
[ 81.250792@0] sdioh_set_mode: set txglom_mode to multi-desc
[ 81.256278@0] Final fw_path=/lib/firmware/brcm/fw_bcm43455c0_ag.bin
[ 81.262507@0] Final nv_path=/lib/firmware/brcm/
[ 81.266994@0] Final conf_path=/lib/firmware/brcm/config.txt
[ 81.329823@0] dhdsdio_download_nvram: error reading nvram file: -21
[ 81.334505@0] _dhdsdio_download_firmware: dongle nvram file download failed
[ 81.341426@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 81.346715@0] dhd_prot_ioctl : bus is down. we have nothing to do
[ 81.352789@0] dhd_net_bus_devreset: dhd_bus_devreset: -35
[ 81.358167@0] wifi_platform_set_power = 0
[ 81.362082@0] ======== PULL WL_REG_ON LOW! ========
[ 81.366917@0] wl_android_wifi_on: Failed
[ 81.370795@0] dhd_open : wl_android_wifi_on failed (-35)
[ 81.376039@0] dhd_stop: Enter ffffffc052f22000
[ 81.380453@0] wl_android_wifi_off in 1
[ 81.384172@0] wl_android_wifi_off in 2: g_wifi_on=0
[ 81.388991@0] wl_android_wifi_off out
[ 81.392596@0] dhd_stop: Exit
[ 81.396102@0] dhd_open: Exit ret=-1
[ 81.402622@0] dhd_open: Enter ffffffc052f22000
[ 81.406146@0]
[ 81.406146@0] Dongle Host Driver, version 1.201.59.6 (r506368)
[ 81.406146@0] Compiled in drivers/net/wireless/bcmdhd
[ 81.423720@0] wl_android_wifi_on in 1
[ 81.427350@0] wl_android_wifi_on in 2: g_wifi_on=0
[ 81.432035@0] wifi_platform_set_power = 1
[ 81.435963@0] ======== PULL WL_REG_ON HIGH! ========
[ 81.440921@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Disable! 240
[ 81.647796@0] aml_wifi wifi.33: [extern_wifi_set_enable] WIFI Enable! 240
[ 82.158578@1] sdio_reset_comm():
[ 82.191163@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 82.198350@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 82.205464@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 82.214619@4] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 82.312664@4] sdio: clk 200000000 SDR mode tuning start
[ 82.317355@4] sdio: rx_tuning_result[0] = 10
[ 82.322014@4] sdio: rx_tuning_result[1] = 10
[ 82.326562@4] sdio: rx_tuning_result[2] = 10
[ 82.331012@4] sdio: rx_tuning_result[3] = 10
[ 82.335099@3] sdio: best_win_start =0, best_win_size =4
[ 82.338883@3] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x22000
[ 82.346177@3] sdio: gclock
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment