apt-get install nut
/etc/nut/nut.conf:MODE=netclient
/etc/nut/upsmon.conf:
MONITOR <system> <powervalue> <username> <password> ("master"|"slave"):MONITOR [email protected] 1 upsmon password slave
upsmon start
upsc <name> for direct attached units or upsc <name>@<address> for remoteupsc [email protected]
Thanks a lot for this !
Still works as i should on 7.2-5, thank you
Wow, this is way simpler than I thought. Looked everywhere for this, thank you!
Thank you! Any tips for polling intervals?
Any tips for polling intervals?
client: upsmon.conf > POLLFREQ (5 sec by default)
server: ups.conf > pollinterval (2 sec by default)
Although, full doc is worth the time and not too long/complex as other man entries often get:
https://networkupstools.org/docs/man/ups.conf.html
https://networkupstools.org/docs/man/upsmon.conf.html
For Proxmox running as client, is there a need for a shutdown script .. as is all vm do close and then the prox server shutdown or it's a panic shutdown of all ? thanks for precision.
For Proxmox running as client, is there a need for a shutdown script .. as is all vm do close and then the prox server shutdown or it's a panic shutdown of all ? thanks for precision.
It's not required but if you want it to run/do certain things before shutdown then this is where you would put it.
So i did test over the cmd : upsmon -c fsd , and the proxmox box as client do shutdown. But if communication fail it don't do anything, it just if the ups get the battery dead. I do see other config as :
nano /etc/nut/upsmon.conf
MONITOR [email protected] 1 upsmon secret slave
MINSUPPLIES 1
SHUTDOWNCMD "/sbin/shutdown -h"
NOTIFYCMD /usr/sbin/upssched
POLLFREQ 2
POLLFREQALERT 1
HOSTSYNC 15
DEADTIME 15
# MAXAGE 24 //mean?
POWERDOWNFLAG /etc/killpower
# Notification message:
NOTIFYMSG ONLINE "UPS %s on line power"
NOTIFYMSG ONBATT "UPS %s on battery"
NOTIFYMSG LOWBATT "UPS %s battery is low"
NOTIFYMSG FSD "UPS %s: forced shutdown in progress"
NOTIFYMSG COMMOK "Communications with UPS %s established"
NOTIFYMSG COMMBAD "Communications with UPS %s lost"
NOTIFYMSG SHUTDOWN "Auto logout and shutdown proceeding"
NOTIFYMSG REPLBATT "UPS %s battery needs to be replaced"
NOTIFYMSG NOCOMM "UPS %s is unavailable"
NOTIFYMSG NOPARENT "upsmon parent process died - shutdown impossible"
# Notification events : go syslog - broadcast msg - exec .script?
NOTIFYFLAG ONLINE SYSLOG+WALL+EXEC
NOTIFYFLAG ONBATT SYSLOG+WALL+EXEC
NOTIFYFLAG LOWBATT SYSLOG+WALL
NOTIFYFLAG FSD SYSLOG+WALL+EXEC
NOTIFYFLAG COMMOK SYSLOG+WALL+EXEC
NOTIFYFLAG COMMBAD SYSLOG+WALL+EXEC
NOTIFYFLAG SHUTDOWN SYSLOG+WALL+EXEC
NOTIFYFLAG REPLBATT SYSLOG+WALL
NOTIFYFLAG NOCOMM SYSLOG+WALL+EXEC
NOTIFYFLAG NOPARENT SYSLOG+WALL
RBWARNTIME 43200
NOCOMMWARNTIME 600
FINALDELAY 5
-=-=-=-=-
sudo nano /etc/nut/upssched.conf
# scheduler to shutdown
CMDSCRIPT /etc/nut/upssched-cmd
PIPEFN /etc/nut/upssched.pipe
LOCKFN /etc/nut/upssched.lock
# timer in sec
AT ONBATT * START-TIMER onbatt 30
AT ONLINE * CANCEL-TIMER onbatt online
AT ONBATT * START-TIMER earlyshutdown 30
AT LOWBATT * EXECUTE onbatt
AT COMMBAD * START-TIMER commbad 30
AT COMMOK * CANCEL-TIMER commbad commok
AT NOCOMM * EXECUTE commbad
AT SHUTDOWN * EXECUTE powerdown
# AT SHUTDOWN * EXECUTE powerdown
is a script is needed ? Do you have an example or you just used nut at when no more power in the ups, then the proxmox box go for shutoff ?
No other scripts in my setup. It is a graceful shutdown including all VMs.
Client performs action based on server configuration.
My server is NUT service inside TrueNAS VM. It is configured to shutdown after N minutes of ONBATT state.
If communication is lost NUT should spam you with e-mails until it is fixed, but there must be a valid account configured for each system's e-mail MTA (e.g. postfix)
This is nice.