AVR microcontroller sleep demonstrations

AVR Sleep

Simple demonstrations of putting AVR microcontrollers to sleep in power-down mode,
which results in minimum current.  Coded with Arduino IDE version 1.0.4 (and with
the Arduino-Tiny core for the ATtiny MCUs, http://code.google.com/p/arduino-tiny/)

For ATmega328P, ~0.1µA.
For ATtinyX5 revisions that implement software BOD disable, ~0.1µA,
for ATtinyX5 revisions that don't, ~20µA.

sleep_ATmega328P.ino

/*----------------------------------------------------------------------*
 * Sleep demo for ATmega328P.                                           *
 * Wire a button from digital pin 2 (INT0) to ground.                   *
 * Wire an LED with an appropriate dropping resistor from pin D13 to    *
 * ground.                                                              *
 * Pushing the button wakes the MCU.                                    *
 * After waking, the MCU flashes the LED, then waits 10 seconds before  *
 * going back to sleep.                                                 *
 *                                                                      *
 * Jack Christensen 07May2013                                           *
 *                                                                      *
 * Tested with Arduino 1.0.5 and an Arduino Uno.                        *
 * Test conditions for all results below:                               *
 *   5V regulated power supply, fed to the Vin pin                      *
 *   16MHz system clock                                                 *
 *   Fuse bytes (L/H/E): 0xFF / 0xDE / 0x05                             *
 *   Optiboot bootloader                                                *
 *                                                                      *
 * Uno R1                                                               *
 *   38mA active, 26mA with MCU in power-down mode.                     *
 *                                                                      *
 * Uno SMD edition                                                      *
 *   42mA active, 31mA power-down.                                      *
 *                                                                      *
 * Adafruit Boarduino                                                   *
 *   Power select jumper set to "USB", USB (FTDI) not connected.        *
 *   15mA active, 3mA power-down.                                       *
 *                                                                      *
 * Adafruit Boarduino without power LED                                 *
 *   12mA active, 0.1µA power-down.                                     *
 *                                                                      *
 * Breadboarded ATmega328P-PU                                           *
 *   12mA active, 0.1µA power-down.                                     *
 *                                                                      *
 * This work is licensed under the Creative Commons Attribution-        *
 * ShareAlike 3.0 Unported License. To view a copy of this license,     *
 * visit http://creativecommons.org/licenses/by-sa/3.0/ or send a       *
 * letter to Creative Commons, 171 Second Street, Suite 300,            *
 * San Francisco, California, 94105, USA.                               *
 *----------------------------------------------------------------------*/ 
 
#include <avr/sleep.h>

const int LED = 13;                          //LED on pin 13
const unsigned long KEEP_RUNNING = 10000;    //milliseconds

void setup(void)
{
    //to minimize power consumption while sleeping, output pins must not source
    //or sink any current. input pins must have a defined level; a good way to
    //ensure this is to enable the internal pullup resistors.

    for (byte i=0; i<20; i++) {    //make all pins inputs with pullups enabled
        pinMode(i, INPUT_PULLUP);
    }

    pinMode(LED, OUTPUT);          //make the led pin an output
    digitalWrite(LED, LOW);        //drive it low so it doesn't source current
}

void loop(void)
{
    for (byte i=0; i<5; i++) {     //flash the LED
        digitalWrite(LED, HIGH);
        delay(100);
        digitalWrite(LED, LOW);
        delay(100);
    }
    delay(KEEP_RUNNING);           //opportunity to measure active supply current 
    digitalWrite(LED, HIGH);       //one blink before sleeping
    delay(100);
    digitalWrite(LED, LOW);
    goToSleep();
}

void goToSleep(void)
{
    byte adcsra = ADCSRA;          //save the ADC Control and Status Register A
    ADCSRA = 0;                    //disable the ADC
    EICRA = _BV(ISC01);            //configure INT0 to trigger on falling edge
    EIMSK = _BV(INT0);             //enable INT0
    set_sleep_mode(SLEEP_MODE_PWR_DOWN);
    cli();                         //stop interrupts to ensure the BOD timed sequence executes as required
    sleep_enable();
    //disable brown-out detection while sleeping (20-25µA)
    uint8_t mcucr1 = MCUCR | _BV(BODS) | _BV(BODSE);
    uint8_t mcucr2 = mcucr1 & ~_BV(BODSE);
    MCUCR = mcucr1;
    MCUCR = mcucr2;
    //sleep_bod_disable();           //for AVR-GCC 4.3.3 and later, this is equivalent to the previous 4 lines of code
    sei();                         //ensure interrupts enabled so we can wake up again
    sleep_cpu();                   //go to sleep
    sleep_disable();               //wake up here
    ADCSRA = adcsra;               //restore ADCSRA
}

//external interrupt 0 wakes the MCU
ISR(INT0_vect)
{
    EIMSK = 0;                     //disable external interrupts (only need one to wake up)
}

sleep_ATtinyX4.ino

/*----------------------------------------------------------------------*
 * Sleep demo for ATtinyX4.                                             *
 * Wire a button from pin D2 (INT0, PB2, DIP pin 5) to ground.          *
 * Wire an LED with an appropriate dropping resistor from pin           *
 * D0 (PB0, DIP pin 2) to ground.                                       *
 * Pushing the button wakes the MCU.                                    *
 * After waking, the MCU flashes the LED, then waits 10 seconds before  *
 * going back to sleep.                                                 *
 *                                                                      *
 * Jack Christensen 04Nov2013                                           *
 *                                                                      *
 * Developed with Arduino 1.0.5.                                        *
 * Test conditions for all results below:                               *
 *   5V or 3.3V regulated power supply                                  *
 *   8MHz system clock (internal RC oscillator)                         *
 *   Fuse bytes (L/H/E): 0xE2 / 0xD5 / 0xFF                             *
 *   Arduino-Tiny core, http://code.google.com/p/arduino-tiny/          *
 *                                                                      *
 * ATtiny84A-PU                                                         *
 *   Vcc=5V:   4.9mA active, 0.1µA power-down.                          *
 *   Vcc=3.3V: 3.1mA active, 0.1µA power-down.                          *
 *                                                                      *
 * This work is licensed under the Creative Commons Attribution-        *
 * ShareAlike 3.0 Unported License. To view a copy of this license,     *
 * visit http://creativecommons.org/licenses/by-sa/3.0/ or send a       *
 * letter to Creative Commons, 171 Second Street, Suite 300,            *
 * San Francisco, California, 94105, USA.                               *
 *----------------------------------------------------------------------*/ 
 
#include <avr/sleep.h>

const int LED_PIN = 0;
const unsigned long KEEP_RUNNING = 10000;    //milliseconds

void setup(void)
{
    //to minimize power consumption while sleeping, output pins must not source
    //or sink any current. input pins must have a defined level; a good way to
    //ensure this is to enable the internal pullup resistors.

    for (byte i=0; i<11; i++) {    //make all pins inputs with pullups enabled
        pinMode(i, INPUT_PULLUP);
    }
    pinMode(LED_PIN, OUTPUT);      //make the led pin an output
    digitalWrite(LED_PIN, LOW);    //drive it low so it doesn't source current
}

void loop(void)
{
    for (byte i=0; i<5; i++) {     //wake up, flash the LED
        digitalWrite(LED_PIN, HIGH);
        delay(100);
        digitalWrite(LED_PIN, LOW);
        delay(100);
    }
    delay(KEEP_RUNNING);           //opportunity to measure active supply current 
    digitalWrite(LED_PIN, HIGH);   //blink LED once before sleeping
    delay(100);
    digitalWrite(LED_PIN, LOW);
    goToSleep();
}

void goToSleep(void)
{
    set_sleep_mode(SLEEP_MODE_PWR_DOWN);
    sleep_enable();
    MCUCR &= ~(_BV(ISC01) | _BV(ISC00));      //INT0 on low level
    GIMSK |= _BV(INT0);                       //enable INT0
    byte adcsra = ADCSRA;                     //save ADCSRA
    ADCSRA &= ~_BV(ADEN);                     //disable ADC
    cli();                                    //stop interrupts to ensure the BOD timed sequence executes as required
    byte mcucr1 = MCUCR | _BV(BODS) | _BV(BODSE);  //turn off the brown-out detector
    byte mcucr2 = mcucr1 & ~_BV(BODSE);
    MCUCR = mcucr1;
    MCUCR = mcucr2;
    sei();                                    //ensure interrupts enabled so we can wake up again
    sleep_cpu();                              //go to sleep
    sleep_disable();                          //wake up here
    ADCSRA = adcsra;                          //restore ADCSRA
}

//external interrupt 0 wakes the MCU
ISR(INT0_vect)
{
    GIMSK = 0;                     //disable external interrupts (only need one to wake up)
}

sleep_ATtinyX5.ino

/*----------------------------------------------------------------------*
 * Sleep demo for ATtinyX5.                                             *
 * Wire a button from pin D2 (INT0, PB2, DIP pin 7) to ground.          *
 * Wire an LED with an appropriate dropping resistor from pin           *
 * D4 (PB4, DIP pin 3) to ground.                                       *
 * Pushing the button wakes the MCU.                                    *
 * After waking, the MCU flashes the LED, then waits 10 seconds before  *
 * going back to sleep.                                                 *
 *                                                                      *
 * Jack Christensen 07May2013                                           *
 *                                                                      *
 * Developed with Arduino 1.0.4.                                        *
 * Test conditions for all results below:                               *
 *   5V regulated power supply                                          *
 *   8MHz system clock (internal RC oscillator)                         *
 *   Fuse bytes (L/H/E): 0xE2 / 0xD5 / 0xFF                             *
 *   Arduino-Tiny core, http://code.google.com/p/arduino-tiny/          *
 *                                                                      *
 * Note that only the ATtinyX5 devices below have BOD disable           *
 * functionality implemented. With Vcc=5V, the BOD will draw            *
 * 20-25µA, depending on temperature.                                   *
 *   ATtiny25, revision E, and newer                                    *
 *   ATtiny45, revision D, and newer                                    *
 *   ATtiny85, revision C, and newer                                    *
 *                                                                      *
 * ATtiny45V-10PU, Rev. G                                               *
 *   7.4mA active, 0.1µA power-down.                                    *
 *                                                                      *
 * ATtiny85V-10PU, Rev. B                                               *
 *   7.1mA active, 21µA power-down.                                     *
 *                                                                      *
 * This work is licensed under the Creative Commons Attribution-        *
 * ShareAlike 3.0 Unported License. To view a copy of this license,     *
 * visit http://creativecommons.org/licenses/by-sa/3.0/ or send a       *
 * letter to Creative Commons, 171 Second Street, Suite 300,            *
 * San Francisco, California, 94105, USA.                               *
 *----------------------------------------------------------------------*/ 
 
#include <avr/sleep.h>

#define LED 4                      //LED on pin 4, PB4, DIP pin 3
#define KEEP_RUNNING 10000         //milliseconds
#define BODS 7                     //BOD Sleep bit in MCUCR
#define BODSE 2                    //BOD Sleep enable bit in MCUCR

void setup(void)
{
    //to minimize power consumption while sleeping, output pins must not source
    //or sink any current. input pins must have a defined level; a good way to
    //ensure this is to enable the internal pullup resistors.

    for (byte i=0; i<5; i++) {     //make all pins inputs with pullups enabled
        pinMode(i, INPUT);
        digitalWrite(i, HIGH);
    }

    pinMode(LED, OUTPUT);          //make the led pin an output
    digitalWrite(LED, LOW);        //drive it low so it doesn't source current
}

void loop(void)
{
    goToSleep();

    for (byte i=0; i<5; i++) {     //wake up, flash the LED
        digitalWrite(LED, HIGH);
        delay(100);
        digitalWrite(LED, LOW);
        delay(100);
    }
    delay(KEEP_RUNNING);           //opportunity to measure active supply current 
}

void goToSleep(void)
{
    byte adcsra, mcucr1, mcucr2;

    set_sleep_mode(SLEEP_MODE_PWR_DOWN);
    sleep_enable();
    MCUCR &= ~(_BV(ISC01) | _BV(ISC00));      //INT0 on low level
    GIMSK |= _BV(INT0);                       //enable INT0
    adcsra = ADCSRA;                          //save ADCSRA
    ADCSRA &= ~_BV(ADEN);                     //disable ADC
    cli();                                    //stop interrupts to ensure the BOD timed sequence executes as required
    mcucr1 = MCUCR | _BV(BODS) | _BV(BODSE);  //turn off the brown-out detector
    mcucr2 = mcucr1 & ~_BV(BODSE);            //if the MCU does not have BOD disable capability,
    MCUCR = mcucr1;                           //  this code has no effect
    MCUCR = mcucr2;
    sei();                                    //ensure interrupts enabled so we can wake up again
    sleep_cpu();                              //go to sleep
    sleep_disable();                          //wake up here
    ADCSRA = adcsra;                          //restore ADCSRA
}

//external interrupt 0 wakes the MCU
ISR(INT0_vect)
{
    GIMSK = 0;                     //disable external interrupts (only need one to wake up)
}

Hello, thank you for your work.

I'm using sleep_ATtinyX5.ino and it works normally as described, but if the PB2 pin remains in the same state after the KEEP_RUNNING the program contained in the loop no longer runs.

Do you have any idea to help me?

Thanks

The problem is that your code and the pin connected to INT0 remaining low will take your MCU to sleep with external interrupts disabled so that it will not be able to wake up.
MCUCR &= ~(_BV(ISC01) | _BV(ISC00)); //INT0 on low level
GIMSK |= _BV(INT0); //enable INT0

GIMSK = 0;

sleep_cpu(); //go to sleep

Check the sequence of those three lines. As long as PB2 is low, the ISR is called after (//enable INT0), then ISR disables all interrupts ( GIMSK = 0 ) so that sleep_cpu() is called without interrupts enabled.

You can solve this by changing the interrupt is activated to either rising or falling edge or just any logical change, eg MCUCR &= _BV(ISC00);

Hey, I'm new to programming AVRs and found this very useful, thanks! I use the ATmega328P and the code snippet works. However, I hand to comment out the code in the interrupt service routine, otherwise it would always only wake once then had to be reset. Do you have an educated guess why?

I have been having issues where the device does not wake up if noise is present during execution.
I have moved all of void loop to void sleep

void loop(void)
{
    goToSleep();
}

void goToSleep(void)
{
    delay(1000);           //opportunity to measure active supply current 
    digitalWrite(LED, HIGH);       //one blink before sleeping
    delay(1000);
    digitalWrite(LED, LOW);   
    byte adcsra = ADCSRA;          //save the ADC Control and Status Register A
    ADCSRA = 0;                    //disable the ADC
    EICRA = _BV(ISC00);            //configure INT0 to trigger on change

and changed interrupts at the end so it can trigger even if switched rapidly
//external interrupt 0 wakes the MCU ISR(INT0_vect) { EIMSK = _BV(INT0); }
I think it works now

@SixProjects That seems like a software solution for a hardware problem. Without knowing all the particulars, perhaps that's a reasonable approach but my first thought would be to address the noise.

Thank you for sharing.