Serial bootlog of the Logilink WC0030A or Apexis APM-JP8015-WS

bootlog_WC0030A_APM-JP8015-WS

U-Boot 1.1.3 (Nov 18 2012 - 20:35:15)

Board: Ralink APSoC DRAM:  32 MB
relocate_code Pointer at: 81fb4000
***********************
Watchdog Reset Occurred
***********************
spi_wait_nsec: 42 
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
raspi_read: from:20000 len:1000 
.*** Warning - bad CRC, using default environment

============================================ 
Ralink UBoot Version: 3.5.3.0
-------------------------------------------- 
ASIC 5350_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping 
DRAM_TYPE: SDRAM 
DRAM_SIZE: 256 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 32 MBytes
Flash component: 8 MBytes NOR Flash
Date:Nov 18 2012  Time:20:35:15
============================================ 
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384 

 ##### The CPU freq = 360 MHZ #### 
 estimate memory size =32 Mbytes

Please choose the operation: 
   1: Load system code to SDRAM via TFTP. 
   2: Load system code then write to Flash via TFTP. 
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial. 
   9: Load Boot Loader code then write to Flash via TFTP. 
... 4 ... 3 ... 2 ... 1 ... 0 
   
3: System Boot system code via Flash.
## Booting image at bc040000 ...
raspi_read: from:40000 len:40 
.   Image Name:   Linux Kernel Image
   Created:      2013-05-20   3:39:41 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    2236352 Bytes =  2.1 MB
   Load Address: 80000000
   Entry Point:  80352000
raspi_read: from:40040 len:221fc0 
...................................   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80352000) ...
## Giving linux memsize in MB, 32

Starting kernel ...


LINUX started...

 THIS IS ASIC
Linux version 2.6.21 (root@test) (gcc version 3.4.2) #136 Mon May 20 11:39:34 CST 2013

 The CPU feqenuce set to 360 MHz
CPU revision is: 0001964c
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 8128
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 50808008, status = 11000000
PID hash table entries: 128 (order: 7, 512 bytes)
calculating r4koff... 0015f900(1440000)
CPU frequency 360.00 MHz
Using 180.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 28852k/32768k available (2960k kernel code, 3916k reserved, 435k data, 120k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
deice id : ef 40 17 0 0 (40170000)
W25Q64BV(ef 40170000) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 6 MTD partitions on "raspi":
0x00000000-0x00020000 : "Bootloader"
0x00020000-0x00030000 : "Config"
0x00030000-0x00040000 : "Factory"
0x00040000-0x00170000 : "Kernel"
0x00170000-0x00300000 : "RootFS"
0x00300000-0x00800000 : "user"
Load Ralink DFS Timer Module
RT3xxx EHCI/OHCI init.
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered (default)
Enable Ralink GDMA Controller Module 
GDMA IP Version=2
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.7 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
loop: loaded (max 8 devices)
Ralink APSoC Ethernet Driver Initilization. v2.1  256 rx/tx descriptors allocated, mtu = 1500!
NAPI enable, weight = 32, Tx Ring = 256, Rx Ring = 256
MAC_ADRH -- : 0x000054cd
MAC_ADRL -- : 0xee012915
PROC INIT OK!
PPP generic driver version 2.4.2
PPP BSD Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
PPTP driver version 0.8.1
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
Linux video capture interface: v2.00
block2mtd: version $Revision: 1.1.1.1 $
usbmon: debugfs is not available
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usb 1-1: new high speed USB device using rt3xxx-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver cytherm
drivers/usb/misc/cytherm.c: v1.0:Cypress USB Thermometer driver
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
All bugs added by David S. Miller <[email protected]>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 120k freed

init started: BusyBox v1.12.1 (2012-11-19 22:34:42 PST)

starting pid 635, tty '': '/etc_ro/rcS'
Algorithmics/MIPS FPU Emulator v1.5
Welcome to
     _______  _______  ___     __  ____   _  _   ___
    |  ___  \|   __  ||   |   |__||    \ | || | /  /
    | |___| ||  |__| ||   |__  __ |     \| || |/  /
    |   _   /|   _   ||      ||  || |\     ||     \
    |__| \__\|__| |__||______||__||_| \____||_|\___\

   .             =System Architecture Department=

rt2860v2_sta: module license 'unspecified' taints kernel.


=== pAd = c0092000, size = 534784 ===

<-- RTMPAllocAdapterBlock, Status=0

phy_tx_ring = 0x01f64000, tx_ring = 0xa1f64000

phy_rx_ring0 = 0x01f65000, rx_ring0 = 0xa1f65000
MAC_ADRH -- : 0x000054cd
MAC_ADRL -- : 0xee012915
RT305x_ESW: Link Status Changed
RX DESC a1e91000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
Key1Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
MCS Set = ff 00 00 00 01
<==== rt28xx_init, Status=0
0x1300 = 00064300
switch reg write offset=14, value=5555
switch reg write offset=40, value=1001
switch reg write offset=44, value=1001
switch reg write offset=48, value=1001
switch reg write offset=4c, value=1
switch reg write offset=50, value=2001
switch reg write offset=70, value=ffffffff
switch reg write offset=98, value=7f7f
switch reg write offset=e4, value=7f
done.
mkdir: cannot create directory '/var/run': File exists
i2cdrv_major = 218
i2s init
gpiomode..........:4042d8
Ralink gpio driver initialized
Ralink APSoC Hardware Watchdog Timer
RT305x_ESW: Link Status Changed

starting pid 690, tty '/dev/ttyS1': '/bin/sh'


BusyBox v1.12.1 (2012-11-19 22:34:42 PST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

# Started WatchDog Timer.
ipcamn uses obsolete (PF_INET,SOCK_PACKET)
Found format MJPEG.
- 640x480 (30.0 fps)
- 352x288 (30.0 fps)
- 320x240 (30.0 fps)
- 176x144 (30.0 fps)
- 160x120 (30.0 fps)
Found format YUV 4:2:2 (YUYV).
- 640x480 (30.0 fps)
- 352x288 (30.0 fps)
- 320x240 (30.0 fps)
- 176x144 (30.0 fps)
- 160x120 (30.0 fps)
uvcvideo: Found UVC 1.00 device USB 2.0 PC Camera (058f:3861)
uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Enabling workaround.
input: USB 2.0 PC Camera as /class/input/input0
usbcore: registered new interface driver uvcvideo
USB Video Class driver (SVN r209)

#