Skip to content

Instantly share code, notes, and snippets.

Boot SPL 2021.04 (Apr 17 2023 - 21:10:33 +0200)
DRAM: 4096 MiB
Trying to boot from MMC1
NOTICE: BL31: v2.8(debug):v12.13.1-v34-Pre-89-g0363c0dd1b-68-gc3131523-dirty
NOTICE: BL31: Built : 20:57:15, Apr 17 2023
NOTICE: BL31: Detected Allwinner H616 SoC (1823)
NOTICE: BL31: Found U-Boot DTB at 0x4a087088, model: Tanix TX6s (axp313)
INFO: ARM GICv2 driver initialized
INFO: Configuring SPC Controller
INFO: PMIC: Probing AXP305 on RSB
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.2.10 (piotro@minimyth2-aarch64) (aarch64-minimyth-linux-gnu-gcc (GCC) 12.2.0, GNU ld (GNU Binutils) 2.40) #1 SMP PREEMPT Thu Apr 6 13:16:47 CEST 2023
[ 0.000000] Machine model: Tanix TX6s (axp313)
[ 0.000000] efi: UEFI not found.
[ 0.000000] earlycon: uart0 at MMIO32 0x0000000005000000 (options '115200n8')
[ 0.000000] printk: bootconsole [uart0] enabled
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x00000000ffffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal [mem 0x0000000100000000-0x000000013fffffff]
U-Boot SPL 2021.04 (Apr 08 2023 - 12:34:31 +0200)
DRAM: 4096 MiB
Trying to boot from MMC1
NOTICE: BL31: v2.8(debug):v12.13.0-v33-Pre-1175-g91e3da68e6-118-gcc455b8f-dirty
NOTICE: BL31: Built : 18:28:24, Apr 7 2023
NOTICE: BL31: Detected Allwinner H616 SoC (1823)
NOTICE: BL31: Found U-Boot DTB at 0x4a087088, model: Tanix TX6s (axp313)
INFO: ARM GICv2 driver initialized
INFO: Configuring SPC Controller
INFO: PMIC: Probing AXP305 on RSB
��������0&������g�v�#�@������ ����������y��0������
U-Boot SPL 2021.04 (Apr 08 2023 - 12:34:31 +0200)
DRAM: 4096 MiB
Trying to boot from MMC1
NOTICE: BL31: v2.8(debug):v12.13.0-v33-Pre-1175-g91e3da68e6-118-gcc455b8f-dirty
NOTICE: BL31: Built : 18:28:24, Apr 7 2023
NOTICE: BL31: Detected Allwinner H616 SoC (1823)
NOTICE: BL31: Found U-Boot DTB at 0x4a087088, model: Tanix TX6s (axp313)
INFO: ARM GICv2 driver initialized
[224]HELLO! BOOT0 is starting!
[227]BOOT0 commit : 3ae35eb
[230]set pll start
[233]periph0 has been enabled
[236]set pll end
[238]unknow PMU
[239]unknow PMU
[241]PMU: AXP1530
[243]dram return write ok
[246]board init ok