Connecting an IPS TFT display (ST7789) to an arduino nano and testing image output.

nanodisplaytest.md

Guide on connecting a ST7789 display to an Arduino Nano.

I recently decided to order an arduino nano and a tft display from AliExpress. When I looked up online it took me some time to find a clear guide how to connect the display to the arduino, either the display had different pins or it was a slightly different model, but with some trial and error, I managed to get it to work.

What you'll need for this:

• 1x Arduino Nano
• 1x AdaFruit 1.3" 240x240 ST7789 display
• 6x jumper wires or whatever else you can use to connect

Connecting display to the arduino

Connect the display pins to arduino like so:

• GND to GND
• VCC to 3V3
• SCL to D13
• SDA to D11
• RES to D7
• DC to D9
• BLK to GND if you for some reason want to turn off the backlight, I left it as is

Testing the display

Go to Tools->Manage Libraries and search for gfx install the AdaFruit graphics library and then search for ST7789 and install the display library.

#include <Adafruit_GFX.h> // graphics library
#include <Adafruit_ST7789.h> // library for this display
#include <SPI.h>
#define TFT_CS 10 // if your display has CS pin
#define TFT_RST 8 // reset pin
#define TFT_DC 9 // data pin

Adafruit_ST7789 tft = Adafruit_ST7789(TFT_CS, TFT_DC, TFT_RST);

void setup() {
  tft.init(240, 240, SPI_MODE2); 
  tft.setRotation(2); // rotates the screen
  tft.fillScreen(ST77XX_BLACK); // fills the screen with black colour
  tft.setCursor(10, 10); // starts to write text at y10 x10
  tft.setTextColor(ST77XX_WHITE); // text colour to white you can use hex codes like 0xDAB420 too
  tft.setTextSize(3); // sets font size
  tft.setTextWrap(true);
  tft.print("HELLO WORLD!");
}
void loop() {
  
  }

And that's basically it! You've successfully connected a ST7789 display to an arduino nano!

Hi, It works! I messed up D numbers with pin numbers. After that one issue remained. The clockspeed is very high and the resistive devider i made had too large rise and fall times. After inserting a level shifter MC14050 3.3V is made for all 5 lines. Even than the clock pulsewith which is 80ns is too fast for this level shifter. I have to reduce the SPI speed so the MC14050 can follow . Not using the SPI speed works fine now

Interesting, I wired it directly and it seemed to work fine. Also, it appears that I may have named the variables wrongly (CS and RST)

The manufacturer stated that it works at 3.3V. Since there is no regulator present on the board, supplying 5V directly might work, but it could damage the display over time.

Hi,
I use an ESP32 and TFT with ILI9341 driver now and abandoned the Arduino Nano.
It works perfect and superfast now!

There are a couple of very important notes about this guide.

First, for both Arduino Uno and Nano the display reset wire must go to the D8 pin, not D7! It still may work with D7 sometimes but very very very unstable (since D7 is floating and we do need to reset the display).

Second, the display works with 3.3 Volts and Arduino outputs high logic level as 5 V, so you need some kind of a level shifter. The easiest one is just 4 resistors connected in series with the each wire (SCL, SDA, RES, D/C). For me 220 Ohm works fine. If you are curious why it works - the display driver IC has diodes connected to the each input pin which conduct excessive positive voltage to the driver power line (+3.3 V). The higher resistor you use, the lower current will flow through it, but a too high value may result in transmission speed reduction.

And the last one - probably you need to use SPI_MODE3 instead of SPI_MODE2 since ST7789 datasheet stays it samples the data pin at the rising edge of the clock signal. It still works with SPI_MODE2 (since Arduino delays the clock signal a few nanoseconds relative to the data one and it's enough for ST7789), but for me with both CPOL and CPHA (== SPI_MODE3) it works more stable.

Hi, great instructions. Unfortunately It does not work for me. I followed it to the letter but my screen stays black. After a lot of trying to fix it I saw some image on the screen but with a los of noise (grey stripes). I am using the same display and a nano clone. I also tried with different displays and arduinos but no luck, same issue. Any idea?

Have you tried what the other comments suggested?

…

On Sat, 21 Sept 2024, 17:42 lucasvonherder, ***@***.***> wrote: ***@***.**** commented on this gist. ------------------------------ Hi, great instructions. Unfortunately It does not work for me. I followed it to the letter but my screen stays black. After a lot of trying to fix it I saw some image on the screen but with a los of noise (grey stripes). I am using the same display and a nano clone. I also tried with different displays and arduinos but no luck, same issue. Any idea? — Reply to this email directly, view it on GitHub <https://gist.github.com/MazeW/80cbdd4476d27a4e29491c8038855849#gistcomment-5199963> or unsubscribe <https://github.com/notifications/unsubscribe-auth/ACWG4DDMF4G6SRMYSO57VVLZXWAT7BFKMF2HI4TJMJ2XIZLTSKBKK5TBNR2WLJDUOJ2WLJDOMFWWLO3UNBZGKYLEL5YGC4TUNFRWS4DBNZ2F6YLDORUXM2LUPGBKK5TBNR2WLJDHNFZXJJDOMFWWLK3UNBZGKYLEL52HS4DFVRZXKYTKMVRXIX3UPFYGLK2HNFZXIQ3PNVWWK3TUUZ2G64DJMNZZDAVEOR4XAZNEM5UXG5FFOZQWY5LFVEYTAOBUGMZDCNJTU52HE2LHM5SXFJTDOJSWC5DF> . You are receiving this email because you authored the thread. Triage notifications on the go with GitHub Mobile for iOS <https://apps.apple.com/app/apple-store/id1477376905?ct=notification-email&mt=8&pt=524675> or Android <https://play.google.com/store/apps/details?id=com.github.android&referrer=utm_campaign%3Dnotification-email%26utm_medium%3Demail%26utm_source%3Dgithub> .

I tried most of it but not changing from D7 to D8 because I stupidly directly fixed everything with hard wires.
I think I will switch to ESP32 aswell since also the Wifi connection will be helpfull in the end :)
Thanks for answering!

I am using an Arduino Nano ESP32, is the wiring the same?

I am using an Arduino Nano ESP32, is the wiring the same?

Not quite.