gistfile1.txt

avrdude.exe: Version 6.0.1, compiled on Apr 15 2015 at 19:59:58
             Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
             Copyright (c) 2007-2009 Joerg Wunsch

             System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr\etc\avrdude.conf"

             Using Port                    : COM5
             Using Programmer              : wiring
             Overriding Baud Rate          : 115200
             AVR Part                      : ATmega2560
             Chip Erase delay              : 9000 us
             PAGEL                         : PD7
             BS2                           : PA0
             RESET disposition             : dedicated
             RETRY pulse                   : SCK
             serial program mode           : yes
             parallel program mode         : yes
             Timeout                       : 200
             StabDelay                     : 100
             CmdexeDelay                   : 25
             SyncLoops                     : 32
             ByteDelay                     : 0
             PollIndex                     : 3
             PollValue                     : 0x53
             Memory Detail                 :

                                      Block Poll               Page                       Polled
               Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
               ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
               eeprom        65    10     8    0 no       4096    8      0  9000  9000 0x00 0x00
               flash         65    10   256    0 yes    262144  256   1024  4500  4500 0x00 0x00
               lfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
               hfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
               efuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
               lock           0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
               calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
               signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

             Programmer Type : Wiring
             Description     : Wiring
             Programmer Model: AVRISP
             Hardware Version: 15
             Firmware Version Master : 2.10
             Vtarget         : 0.0 V
             SCK period      : 47.8 us

avrdude.exe: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.01s

avrdude.exe: Device signature = 0x1e9801
avrdude.exe: safemode: lfuse reads as FF
avrdude.exe: safemode: hfuse reads as D8
avrdude.exe: safemode: efuse reads as FF
avrdude.exe: reading input file "C:\Users\Robert Nelson\Documents\Atmel Studio\7.0\GccApplication1\GccApplication1\Debug\GccApplication1.hex"
avrdude.exe: writing flash (256 bytes):

Writing | ################################################## | 100% 0.04s

avrdude.exe: 256 bytes of flash written
avrdude.exe: verifying flash memory against C:\Users\Robert Nelson\Documents\Atmel Studio\7.0\GccApplication1\GccApplication1\Debug\GccApplication1.hex:
avrdude.exe: load data flash data from input file C:\Users\Robert Nelson\Documents\Atmel Studio\7.0\GccApplication1\GccApplication1\Debug\GccApplication1.hex:
avrdude.exe: input file C:\Users\Robert Nelson\Documents\Atmel Studio\7.0\GccApplication1\GccApplication1\Debug\GccApplication1.hex contains 256 bytes
avrdude.exe: reading on-chip flash data:

Reading | ################################################## | 100% 0.04s

avrdude.exe: verifying ...
avrdude.exe: 256 bytes of flash verified

avrdude.exe: safemode: lfuse reads as FF
avrdude.exe: safemode: hfuse reads as D8
avrdude.exe: safemode: efuse reads as FF
avrdude.exe: safemode: Fuses OK (H:FF, E:D8, L:FF)

avrdude.exe done.  Thank you.

mega2560

Arduino Programmer

C:\Program Files (x86)\Arduino\hardware\tools\avr\bin\avrdude.exe

-C "C:\Program Files (x86)\Arduino\hardware\tools\avr\etc\avrdude.conf" -v -D -patmega2560 -cwiring -PCOM5 -b115200 -U flash:w:"$(ProjectDir)Debug\$(TargetName).hex":i