Working on getting Klipper up and running on Trigorilla_Pro_A_V1.0.4

klipper_anycubic.md

Klipper for AnyCubic Kobra Trigorilla_Pro_A_V1.0.4

Code repository: https://github.com/SteveGotthardt/klipper

Status: move r65 to r66 for TMC control

Attaching to target via P4 with SAM-ICE

physical connection: Atmel SAM-ICE 20 pin jumpered to P4

• P4: Pin 1 -> ICE Pin 1 = VTref
• P4: Pin 2 -> ICE Pin 20 = GND
• P4: Pin 3 -> ICE Pin 7 = TMS (used by SWD)
• P4: Pin 4 -> ICE Pin 9 = TCK
• P4: Pin 5 -> ICE Pin 15 = RESET

running J-link commander

• Device: Cortex-M4
• Target Interface: SWD
• Interface Speed: 2000 KHz

finding stuff with J-Mem

• VTOR is at 0xE000ED08
• which shows vector table start now at 0x8000 (was 0x0 at boot)
• which shows stack pointer at 0x20008D10 and reset at 0x82A1 - this is for program that shipped with my board

What is the clock running at:

PLL config @ 0x40054100 CMU_PLLCFGR = 0x1110_3100 (reset is 0x1110_1300)

So it looks like 8MHz XTAL * 50 / 2 is 200MHz system clock

• MPLLM[0:4] = 0, divide by 1
• PLLSRC = 0, XTAL selected (8MHz)
• MPLLN[8:0] = 0x031, mult x 50
• MPLLR[3:0] = 1, divide by 2
• MPLLQ[3:0] = 1, divide by 2
• MPLLP[3:0] = 1, divide by 2

XTAL selection: 0x40054032 CMU_XTALCR = 0, oscillates

XTAL configure: 0x40054410 CMU_XTALCFGR = 0, high-drive, not ultra, oscillates

Clock division of 200MHz system clock

• CMU_SCFGR @ 0x40054020 32 bits after boot: 0x00242210
• PCLK0: divide by 1
• PCLK1: divide by 2
• PCLK2: divide by 4
• PCLK3: divide by 4
• PCLK4: divide by 16
• EXCKS: divide by 4
• HCLKS: divide by 1

TMC UART address mapping

• Z: [10] MS1_AD0 is resistor to GND, MS2_AD1 tied to VCC
  • so Z can be addressed with [10] or [11] without trace-cutting
• Y: [01] MS1_AD0 is tied to VCC, MS2_AD1 is resistor to GND
  • so Y can be addressed with [01] or [11] without trace-cutting
• X: [00] MS1_AD0 and MS_AD1 tied together through resistor to GND
  • so X can be [00] (R65 placed) or [11] (R66 placed)

Fix addressing (no trace cutting, just move resistors):

• remap X address to [11] by moving R65 to R66 (VCC) - TESTED - works!

Extruder driver on my board is MS35775, a 2208 clone

Pin Mapping

• PA0: BED heater
• PA1: E0 heater
• PA2: UART TX to 22ohm to CH340G pin 3 RXD
• PA3: UART RX to 22ohm to CH340G pin 2 TXD
• PA4: X stepper dir
• PA5: X stepper step
• PA6: X tmc2209 endstop = ^diag (StallGuard)
• PA7: Y stepper !dir
• PA8: Z tmc2209 endstop = ^diag (StallGuard)
• PA9: X/Y tmc2209 TX
• PA10: SD, Detect
• PA11:
• PA12:
• PA13: E0 fan
• PA14: MCU fan
• PA15: X/Y/Z tmc2209 RX
• PB0: E1/ZL stepper !dir ZL not installed
• PB1: E1/ZL stepper step
• PB2: E1/ZL endstop = ^diag (StallGuard)
• PB3: Motor control TX
• PB4: Motor control RX
• PB5: Beeper
• PB6: Autolevel RX
• PB7: Autolevel TX
• PB8: Probe
• PB9: fan
• PB10: P3 (LCD), Pin 3 TXD
• PB11:
• PB12: (SPI SSN)
• PB13: (SPI SCK)
• PB14: (SPI MISO)
• PB15: (SPI MOSI)
• PC0: BED sensor -> connector T1
• PC1: E0 sensor
• PC2: Power loss
• PC3: X/Y/Z/E stepper enable (!)
• PC4: Y stepper step
• PC5: Y tmc2209 endstop = ^diag (StallGuard)
• PC6: Z stepper dir
• PC7: Z stepper step
• PC8: SDIO, D0
• PC9: SDIO, D1
• PC10: SDIO, D2
• PC11: SDIO, D3
• PC12: SDIO, CK
• PC13: Filament runout
• PC14: E0 stepper step
• PC15: E0 stepper dir
• PD2: SDIO, CMD
• PH1: (LCD reset)
• PH2: LCD P3, Pin 2 RXD

Board Connectors

LCD - P3

• Pin 1: GND
• Pin 2: MCU pin 1: PH2 RXD
• Pin 3: MCU pin 29: PB10 TXD
• Pin 4: MCU pin 7: NRST (NC)
• Pin 5: 5V

FAN2 (P19) controlled by PA14

T1 (P5)

• Pin 1: PC0 -
• Pin 2: GND

SPI (P20)

Reference

https://www.trinamic.com/fileadmin/assets/Products/ICs_Documents/TMC2202_TMC2208_TMC2224_datasheet_rev1.13.pdf https://www.trinamic.com/fileadmin/assets/Products/ICs_Documents/TMC2209_Datasheet_V103.pdf

I mean, it's definitely the control board, but which element is causing such problems?

I've have no clue, i dont have that much knowledge in these electronics..