Created
June 25, 2016 12:22
-
-
Save TheSkorm/3a47ae86f4f0200fe305efffa277a153 to your computer and use it in GitHub Desktop.
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| # Robot module configurations : general handling of movement G-codes and slicing into moves | |
| arm_solution linear_delta # delta selection | |
| arm_length 226 # this is the length of an arm from hinge to hinge | |
| arm_radius 108.11 # this is the horiontal distance from hinge to hinge when the effector is centered | |
| default_feed_rate 3000 # Default rate ( mm/minute ) for G1/G2/G3 moves | |
| default_seek_rate 3000 # Default rate ( mm/minute ) for G0 moves | |
| mm_per_arc_segment 0.0 # Fixed length for line segments that divide arcs 0 to disable | |
| mm_max_arc_error 0.01 # The maximum error for line segments that divide arcs 0 to disable | |
| # note it is invalid for both the above be 0 | |
| # if both are used, will use largest segment length based on radius | |
| #mm_per_line_segment 5 # Lines can be cut into segments ( not usefull with cartesian coordinates robots ). | |
| delta_segments_per_second 160 # segments per second used for deltas | |
| # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions | |
| alpha_steps_per_mm 80 # Steps per mm for alpha stepper | |
| beta_steps_per_mm 80 # Steps per mm for beta stepper | |
| gamma_steps_per_mm 80 # Steps per mm for gamma stepper | |
| # Planner module configuration : Look-ahead and acceleration configuration | |
| planner_queue_size 32 # DO NOT CHANGE THIS UNLESS YOU KNOW EXACTLY WHAT YOUR ARE DOING | |
| acceleration 3000 # Acceleration in mm/second/second. | |
| acceleration_ticks_per_second 1000 # Number of times per second the speed is updated | |
| junction_deviation 0.05 # Similar to the old "max_jerk", in millimeters, see : https://github.com/grbl/grbl/blob/master/planner.c#L409 | |
| # and https://github.com/grbl/grbl/wiki/Configuring-Grbl-v0.8 . Lower values mean being more careful, higher values means being faster and have more jerk | |
| # Stepper module configuration | |
| microseconds_per_step_pulse 1 # Duration of step pulses to stepper drivers, in microseconds | |
| base_stepping_frequency 100000 # Base frequency for stepping | |
| # Stepper module pins ( ports, and pin numbers, appending "!" to the number will invert a pin ) | |
| alpha_step_pin 2.0 # Pin for alpha stepper step signal | |
| alpha_dir_pin 0.5 # Pin for alpha stepper direction | |
| alpha_en_pin 0.4 # Pin for alpha enable pin | |
| alpha_current 1.2 # X stepper motor current | |
| alpha_max_rate 3000. # mm/min actuator max speed | |
| x_axis_max_speed 3000.0 # mm/min cartesian max speed | |
| beta_step_pin 2.1 # Pin for beta stepper step signal | |
| beta_dir_pin 0.11 # Pin for beta stepper direction | |
| beta_en_pin 0.10 # Pin for beta enable | |
| beta_current 1.2 # Y stepper motor current | |
| beta_max_rate 3000.0 # mm/min | |
| y_axis_max_speed 3000.0 # mm/min | |
| gamma_step_pin 2.2 # Pin for gamma stepper step signal | |
| gamma_dir_pin 0.20 # Pin for gamma stepper direction | |
| gamma_en_pin 0.19 # Pin for gamma enable | |
| gamma_current 1.2 # Z stepper motor current | |
| gamma_max_rate 3000.0 # mm/min | |
| z_axis_max_speed 3000.0 # mm/min | |
| # Extruder module configuration | |
| extruder.hotend.enable true # Whether to activate the extruder module at all. All configuration is ignored if false | |
| extruder.hotend.steps_per_mm 96 # Steps per mm for extruder stepper | |
| extruder.hotend.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves | |
| extruder.hotend.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio | |
| extruder.hotend.max_speed 200 # mm/s | |
| extruder.hotend.step_pin 2.3 # Pin for extruder step signal | |
| extruder.hotend.dir_pin 0.22 # Pin for extruder dir signal | |
| extruder.hotend.en_pin 0.21 # Pin for extruder enable signal | |
| # Hotend temperature control configuration | |
| temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all. All configuration is ignored if false. | |
| temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read | |
| temperature_control.hotend.heater_pin 2.4 # Pin that controls the heater | |
| temperature_control.hotend.thermistor Semitec # see http://smoothieware.org/temperaturecontrol#toc5 | |
| #temperature_control.hotend.beta 4267 # or set the beta value | |
| temperature_control.hotend.set_m_code 104 # | |
| temperature_control.hotend.set_and_wait_m_code 109 # | |
| temperature_control.hotend.designator T # | |
| temperature_control.hotend.max_temp 260 # Set maximum temperature - Will prevent heating above 300 by default | |
| #temperature_control.hotend.min_temp 0 # Set minimum temperature - Will prevent heating below 0 by default | |
| #P39.98 I5.00 D79.91 | |
| # temperature_control.hotend.p_factor 22.2 # | |
| # temperature_control.hotend.i_factor 1.08 # | |
| # temperature_control.hotend.d_factor 114 # | |
| # For bed | |
| temperature_control.bed.enable true # | |
| temperature_control.bed.thermistor_pin 0.25 # | |
| temperature_control.bed.heater_pin 2.5 # | |
| temperature_control.bed.thermistor Semitec # http://smoothieware.org/temperaturecontrol#toc5 | |
| #temperature_control.bed.beta 4267 # or set the beta value | |
| temperature_control.bed.set_m_code 140 # | |
| temperature_control.bed.set_and_wait_m_code 190 # | |
| temperature_control.bed.designator B # | |
| # uncomment followng to use bang bang isntead of PID for the bed (best for relay conrolled hotbeds) | |
| temperature_control.bed.bang_bang true # set to true to use bang bang control rather than PID | |
| temperature_control.bed.hysteresis 2.0 # set to the temperature in degrees C to use as hysteresis when using bang bang | |
| # Switch module for fan control | |
| switch.fan.enable true # | |
| switch.fan.input_on_command M106 # | |
| switch.fan.input_off_command M107 # | |
| switch.fan.output_pin 2.7 # | |
| # automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes | |
| # useful to turn on a fan or water pump to cool the hotend | |
| #temperatureswitch.hotend.enable true # | |
| #temperatureswitch.hotend.designator T # first character of the temperature control designator to use as the temperature sensor to monitor | |
| #temperatureswitch.hotend.switch misc # select which switch to use, matches the name of the defined switch | |
| #temperatureswitch.hotend.threshold_temp 60.0 # temperature to turn on (if rising) or off the switch | |
| #temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals | |
| #temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals | |
| # switch.psu.enable true # turn atx on/off | |
| # switch.psu.input_on_command M80 # | |
| # switch.psu.input_off_command M81 # | |
| # switch.psu.output_pin 2.13o! # open drain, inverted | |
| # Switch module for spindle control | |
| #switch.spindle.enable false # | |
| # Endstops | |
| endstops_enable true # the endstop module is enabled by default and can be disabled here | |
| delta_homing true # forces all three axis to home a the same time regardless of what is specified in G28 | |
| alpha_max_endstop 1.24!^ # | |
| alpha_homing_direction home_to_max # or set to home_to_max and set alpha_max | |
| alpha_min 0 # this gets loaded after homing when home_to_min is set | |
| alpha_max 0 # this gets loaded after homing when home_to_max is set | |
| beta_max_endstop 1.26!^ # | |
| beta_homing_direction home_to_max # | |
| beta_min 0 # | |
| beta_max 0 # | |
| gamma_max_endstop 1.28!^ # | |
| gamma_homing_direction home_to_max # | |
| gamma_min 0 # | |
| gamma_max 280 # change to suit your height | |
| #probe endstop | |
| #probe_pin 1.29 # optional pin for probe | |
| alpha_fast_homing_rate_mm_s 80 # feedrates in mm/second | |
| beta_fast_homing_rate_mm_s 80 # " | |
| gamma_fast_homing_rate_mm_s 80 # " | |
| alpha_slow_homing_rate_mm_s 20 # " | |
| beta_slow_homing_rate_mm_s 20 # " | |
| gamma_slow_homing_rate_mm_s 20 # " | |
| alpha_homing_retract_mm 5 # distance in mm | |
| beta_homing_retract_mm 5 # " | |
| gamma_homing_retract_mm 5 # " | |
| alpha_trim 0 # software trim for alpha stepper endstop (in mm) - moves down | |
| beta_trim 0 # software trim for beta stepper endstop (in mm) | |
| gamma_trim 0 # software trim for gamma stepper endstop (in mm) | |
| # optional enable limit switches, actions will stop if any enabled limit switch is triggered | |
| #alpha_limit_enable false # set to true to enable X min and max limit switches | |
| #beta_limit_enable false # set to true to enable Y min and max limit switches | |
| #gamma_limit_enable false # set to true to enable Z min and max limit switches | |
| #move_to_origin_after_home true # move XY to 0,0 after homing | |
| # optional Z probe http://smoothieware.org/zprobe | |
| zprobe.enable true # set to true to enable a zprobe | |
| zprobe.probe_pin 1.29! # pin probe is attached to if NC remove the ! | |
| zprobe.slow_feedrate 5 # mm/sec probe feed rate | |
| #zprobe.debounce_count 100 # set if noisy | |
| zprobe.fast_feedrate 100 # move feedrate | |
| zprobe.probe_height 10 # how much above bed to start probe | |
| # associated with zprobe the leveling strategy to use | |
| leveling-strategy.delta-calibration.enable true # basic delta calibration | |
| leveling-strategy.delta-calibration.radius 60 # the probe radius | |
| # kill button (used to be called pause) maybe assigned to a different pin, set to the onboard pin by default | |
| kill_button_enable false # set to true to enable a kill button | |
| kill_button_pin 2.12 # kill button pin. default is same as pause button 2.12 (2.11 is another good choice) | |
| # Panel See http://smoothieware.org/panel | |
| panel.enable false # set to true to enable the panel code | |
| # Example viki2 config for an azteeg miniV2 with IDC cable | |
| panel.lcd viki2 # set type of panel | |
| panel.spi_channel 0 # set spi channel to use P0_18,P0_15 MOSI,SCLK | |
| panel.spi_cs_pin 0.16 # set spi chip select | |
| panel.encoder_a_pin 3.25!^ # encoder pin | |
| panel.encoder_b_pin 3.26!^ # encoder pin | |
| panel.click_button_pin 2.11!^ # click button | |
| panel.a0_pin 2.6 # st7565 needs an a0 | |
| #panel.contrast 8 # override contrast setting (default is 9) | |
| #panel.encoder_resolution 4 # override number of clicks to move 1 item (default is 4) | |
| #panel.button_pause_pin 1.22^ # kill/pause set one of these for the auxilliary button on viki2 | |
| #panel.back_button_pin 1.22!^ # back button recommended to use this on EXP1 | |
| panel.buzz_pin 0.25 # pin for buzzer on EXP2 | |
| panel.red_led_pin 2.8 # pin for red led on viki2 on EXP1 | |
| panel.blue_led_pin 4.29 # pin for blue led on viki2 on EXP1 | |
| panel.external_sd true # set to true if there is an extrernal sdcard on the panel | |
| panel.external_sd.spi_channel 0 # set spi channel the sdcard is on | |
| panel.external_sd.spi_cs_pin 1.23 # set spi chip select for the sdcard | |
| panel.external_sd.sdcd_pin 1.31!^ # sd detect signal (set to nc if no sdcard detect) | |
| panel.menu_offset 1 # some panels will need 1 here | |
| # Example mini viki2 config | |
| #panel.lcd mini_viki2 # set type of panel | |
| #panel.spi_channel 0 # set spi channel to use P0_18,P0_15 MOSI,SCLK | |
| #panel.spi_cs_pin 0.16 # set spi chip select | |
| #panel.encoder_a_pin 3.25!^ # encoder pin | |
| #panel.encoder_b_pin 3.26!^ # encoder pin | |
| #panel.click_button_pin 2.11!^ # click button | |
| #panel.a0_pin 2.6 # st7565 needs an a0 | |
| ##panel.contrast 18 # override contrast setting (default is 18) | |
| ##panel.encoder_resolution 2 # override number of clicks to move 1 item (default is 2) | |
| #panel.menu_offset 1 # here controls how sensitive the menu is. some panels will need 1 | |
| panel.alpha_jog_feedrate 6000 # x jogging feedrate in mm/min | |
| panel.beta_jog_feedrate 6000 # y jogging feedrate in mm/min | |
| panel.gamma_jog_feedrate 200 # z jogging feedrate in mm/min | |
| panel.hotend_temperature 185 # temp to set hotend when preheat is selected | |
| panel.bed_temperature 60 # temp to set bed when preheat is selected | |
| # Azteeg specific settings do not change | |
| #currentcontrol_module_enable true # | |
| #digipot_max_current 2.4 # max current | |
| #digipot_factor 106.0 # factor for converting current to digipot value | |
| # network settings | |
| #network.enable true # enable the ethernet network services | |
| #network.webserver.enable true # enable the webserver | |
| #network.telnet.enable true # enable the telnet server | |
| #network.plan9.enable true # enable the plan9 network filesystem | |
| #network.ip_address auto # the IP address | |
| #network.ip_mask 255.255.255.0 # the ip mask | |
| #network.ip_gateway 192.168.40.1 # the gateway address | |
| extruder.hotend.retract_length 7 # retract length in mm | |
| extruder.hotend.retract_feedrate 66 # retract feedrate in mm/sec | |
| extruder.hotend.retract_recover_length 0.1 # additional length for recover | |
| extruder.hotend.retract_recover_feedrate 66 # recover feedrate in mm/sec (should be less than retract feedrate) |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment