Config for my Meteor75 Pro

BetaFlight_Meteor75Pro.txt

# Betaflight / STM32G47X (SG47) 4.5.1 Dec 11 2025 / 08:14:05 (77d01ba3b) MSP API: 1.46

batch start
defaults nosave

board_name BETAFPVG473
manufacturer_id BEFH
mcu_id 004800504c45500f20373958
signature 

feature OSD

serial 3 131073 115200 57600 0 115200
map RETA1234

beacon RX_LOST
beacon RX_SET

aux 0 0 0 1700 2100 0 0
aux 1 1 3 1700 2100 0 0
aux 2 2 3 1300 1700 0 0
aux 3 13 2 1700 2100 0 0
aux 4 35 1 1700 2100 0 0


set gyro_lpf1_static_hz = 0
set dyn_notch_count = 1
set dyn_notch_q = 400
set dyn_notch_min_hz = 150
set dyn_notch_max_hz = 300
set gyro_lpf1_dyn_min_hz = 0
set acc_calibration = 12,-14,13,1
set baro_hardware = NONE
set dshot_idle_value = 550
set dshot_bidir = ON
set dshot_bitbang = AUTO
set motor_pwm_protocol = DSHOT300
set motor_poles = 12
set bat_capacity = 580
set vbat_max_cell_voltage = 440
set vbat_warning_cell_voltage = 345
set ibata_scale = 550
set ibata_offset = -100
set small_angle = 180
set osd_warn_bitmask = 458751
set osd_rssi_dbm_alarm = -99
set osd_vbat_pos = 2113
set osd_rssi_pos = 192
set osd_link_quality_pos = 1102
set osd_rssi_dbm_pos = 3119
set osd_rsnr_pos = 160
set osd_tim_1_pos = 386
set osd_tim_2_pos = 1614
set osd_remaining_time_estimate_pos = 33
set osd_flymode_pos = 2104
set osd_throttle_pos = 2625
set osd_vtx_channel_pos = 33
set osd_crosshairs_pos = 2361
set osd_ah_sbar_pos = 314
set osd_ah_pos = 2266
set osd_current_pos = 65
set osd_mah_drawn_pos = 577
set osd_craft_name_pos = 577
set osd_pilot_name_pos = 545
set osd_home_dist_pos = 98
set osd_flight_dist_pos = 130
set osd_warnings_pos = 14773
set osd_avg_cell_voltage_pos = 44
set osd_pit_ang_pos = 97
set osd_rol_ang_pos = 65
set osd_battery_usage_pos = 2081
set osd_disarmed_pos = 2134
set osd_esc_tmp_pos = 129
set osd_esc_rpm_pos = 150
set osd_flip_arrow_pos = 3362
set osd_core_temp_pos = 2145
set osd_sys_vtx_temp_pos = 2177
set debug_mode = GYRO_SCALED
set gyro_1_sensor_align = CW90
set gyro_1_align_yaw = 900
set craft_name = Meteor75 Pro
set pilot_name = Tyrrrz

profile 0
set profile_name = GF 40mm
set dterm_lpf1_dyn_min_hz = 82
set dterm_lpf1_dyn_max_hz = 165
set dterm_lpf1_static_hz = 82
set dterm_lpf2_static_hz = 165
set vbat_sag_compensation = 100
set anti_gravity_gain = 50
set throttle_boost = 0
set p_pitch = 64
set i_pitch = 103
set d_pitch = 67
set f_pitch = 42
set p_roll = 64
set i_roll = 103
set d_roll = 48
set f_roll = 43
set p_yaw = 64
set i_yaw = 103
set f_yaw = 43
set d_min_roll = 43
set d_min_pitch = 58
set auto_profile_cell_count = 1
set thrust_linear = 30
set feedforward_averaging = 2_POINT
set feedforward_smooth_factor = 60
set feedforward_jitter_factor = 10
set dyn_idle_min_rpm = 30
set simplified_master_multiplier = 120
set simplified_i_gain = 90
set simplified_d_gain = 120
set simplified_pi_gain = 120
set simplified_dmax_gain = 40
set simplified_feedforward_gain = 30
set simplified_pitch_d_gain = 120
set simplified_pitch_pi_gain = 95
set simplified_dterm_filter_multiplier = 110
set tpa_rate = 80

rateprofile 0
set thr_mid = 50
set thr_expo = 0
set throttle_limit_type = SCALE
set throttle_limit_percent = 70
set roll_rc_rate = 5
set pitch_rc_rate = 5
set yaw_rc_rate = 5
set roll_srate = 30
set pitch_srate = 30
set yaw_srate = 30
set roll_expo = 0
set pitch_expo = 0
set yaw_expo = 0

save