mr7350 nss error

NAND read: device 0 offset 0x1480000, size 0x800000
 8388608 bytes read: OK
## Loading kernel from FIT Image at 44000000 ...
   Using 'config@1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  ARM64 OpenWrt Linux-6.6.87
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0x440000e8
     Data Size:    7884120 Bytes = 7.5 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x41000000
     Entry Point:  0x41000000
     Hash algo:    crc32
     Hash value:   1f0b34b2
     Hash algo:    sha1
     Hash value:   13f6355c5c8108e50bf42c3636da295dcdee738d
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
   Using 'config@1' configuration
   Trying 'fdt-1' fdt subimage
     Description:  ARM64 OpenWrt linksys_mr7350 device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x44784f80
     Data Size:    46492 Bytes = 45.4 KiB
     Architecture: AArch64
     Hash algo:    crc32
     Hash value:   56951cb0
     Hash algo:    sha1
     Hash value:   7fc47a7412a68ea180f5b012c8796fe87ba27bdb
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x44784f80
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 484f1000, end 484ff59b ... OK
Could not find PCI in device tree
Using machid 0x8030200 from environment

Starting kernel ...

Jumping to AARCH64 kernel via monitor
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x51af8014]
[    0.000000] Linux version 6.6.87 (vladdrako@GMKtec-G3) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r31316-7ec0530427) 13.3.0, GNU ld (GNU Binutils) 2.43.1) #0 SMP Fri Apr 25 14:13:06 2025
[    0.000000] Machine model: Linksys MR7350
[    0.000000] OF: reserved mem: 0x0000000000060000..0x0000000000065fff (24 KiB) nomap non-reusable memory@60000
[    0.000000] OF: reserved mem: 0x0000000040000000..0x0000000040ffffff (16384 KiB) nomap non-reusable nss_region@40000000
[    0.000000] OF: reserved mem: 0x000000004a100000..0x000000004a4fffff (4096 KiB) nomap non-reusable bootloader@4a100000
[    0.000000] OF: reserved mem: 0x000000004a600000..0x000000004a9fffff (4096 KiB) nomap non-reusable memory@4a600000
[    0.000000] OF: reserved mem: 0x000000004aa00000..0x000000004aafffff (1024 KiB) nomap non-reusable memory@4aa00000
[    0.000000] OF: reserved mem: 0x000000004ab00000..0x000000004fffffff (87040 KiB) nomap non-reusable memory@4ab00000
[    0.000000] OF: reserved mem: 0x0000000050000000..0x00000000500fffff (1024 KiB) nomap non-reusable q6_etr_region@50000000
[    0.000000] OF: reserved mem: 0x0000000050100000..0x00000000501fffff (1024 KiB) nomap non-reusable m3_dump_region@50100000
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x0000000040ffffff]
[    0.000000]   node   0: [mem 0x0000000041000000-0x000000004a0fffff]
[    0.000000]   node   0: [mem 0x000000004a100000-0x000000004a4fffff]
[    0.000000]   node   0: [mem 0x000000004a500000-0x000000004a5fffff]
[    0.000000]   node   0: [mem 0x000000004a600000-0x00000000501fffff]
[    0.000000]   node   0: [mem 0x0000000050200000-0x000000005fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 19 pages/cpu s39224 r8192 d30408 u77824
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: Spectre-v4
[    0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[    0.000000] alternatives: applying boot alternatives
[    0.000000] Kernel command line: init=/sbin/init rootfstype=squashfs ubi.mtd=rootfs root=mtd:squashfs rootwait root=/dev/ubiblock0_0 mitigations=off noirqdebug cgroup_disable=memory
[    0.000000] IRQ lockup detection disabled
[    0.000000] cgroup: Disabling memory control group subsystem
[    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129024
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 0MB
[    0.000000] software IO TLB: area num 4.
[    0.000000] software IO TLB: SWIOTLB bounce buffer size roundup to 1MB
[    0.000000] software IO TLB: mapped [mem 0x000000005f4c0000-0x000000005f5c0000] (1MB)
[    0.000000] Memory: 382184K/524288K available (11456K kernel code, 1102K rwdata, 1764K rodata, 1216K init, 321K bss, 142104K reserved, 0K cma-reserved)
[    0.000000] le9 Unofficial (le9uo) working set protection 1.8 by Masahito Suzuki (forked from hakavlad's original le9 patch)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 12 jiffies.
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: 0xffffffc080010000
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 and mmio timer(s) running at 24.00MHz (virt/virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000099] Console: colour dummy device 80x25
[    0.000112] printk: console [tty0] enabled
[    0.000625] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=192000)
[    0.000653] pid_max: default: 32768 minimum: 301
[    0.000993] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.001021] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.001920] spectre-v4 mitigation disabled by command-line option
[    0.002888] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[    0.003109] rcu: Hierarchical SRCU implementation.
[    0.003125] rcu:     Max phase no-delay instances is 1000.
[    0.003338] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.003820] smp: Bringing up secondary CPUs ...
[    0.004426] Detected VIPT I-cache on CPU1
[    0.004533] CPU1: Booted secondary processor 0x0000000001 [0x51af8014]
[    0.005178] Detected VIPT I-cache on CPU2
[    0.005253] CPU2: Booted secondary processor 0x0000000002 [0x51af8014]
[    0.005876] Detected VIPT I-cache on CPU3
[    0.005948] CPU3: Booted secondary processor 0x0000000003 [0x51af8014]
[    0.006024] smp: Brought up 1 node, 4 CPUs
[    0.006091] SMP: Total of 4 processors activated.
[    0.006107] CPU features: detected: 32-bit EL0 Support
[    0.006121] CPU features: detected: CRC32 instructions
[    0.006195] CPU: All CPU(s) started at EL1
[    0.006209] alternatives: applying system-wide alternatives
[    0.021218] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 15290083570200000 ns
[    0.021275] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.021539] pinctrl core: initialized pinctrl subsystem
[    0.022600] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.023232] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[    0.023284] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.023334] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.023758] thermal_sys: Registered thermal governor 'step_wise'
[    0.023765] thermal_sys: Registered thermal governor 'user_space'
[    0.023869] cpuidle: using governor menu
[    0.024191] ASID allocator initialised with 65536 entries
[    0.033816] /soc@0/ssphy@78000/phy@78200: Fixed dependency cycle(s) with /soc@0/clock-controller@1800000
[    0.033953] /soc@0/clock-controller@1800000: Fixed dependency cycle(s) with /soc@0/ssphy@78000/phy@78200
[    0.034114] /soc@0/interrupt-controller@b000000: Fixed dependency cycle(s) with /soc@0/interrupt-controller@b000000
[    0.034523] /soc@0/ssphy@78000: Fixed dependency cycle(s) with /soc@0/clock-controller@1800000
[    0.034559] /soc@0/ssphy@78000/phy@78200: Fixed dependency cycle(s) with /soc@0/clock-controller@1800000
[    0.036816] /soc@0/ssphy@78000/phy@78200: Fixed dependency cycle(s) with /soc@0/clock-controller@1800000
[    0.036917] /soc@0/ssphy@78000: Fixed dependency cycle(s) with /soc@0/clock-controller@1800000
[    0.036950] /soc@0/clock-controller@1800000: Fixed dependency cycle(s) with /soc@0/ssphy@78000/phy@78200
[    0.081709] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[    0.084875] Modules: 28768 pages in range for non-PLT usage
[    0.084885] Modules: 520288 pages in range for PLT usage
[    0.086215] cryptd: max_cpu_qlen set to 1000
[    0.087803] regulator-usb-vbus enforce active low on GPIO handle
[    0.088232] SCSI subsystem initialized
[    0.088448] usbcore: registered new interface driver usbfs
[    0.088496] usbcore: registered new interface driver hub
[    0.088549] usbcore: registered new device driver usb
[    0.089073] qcom_scm: convention: smc arm 64
[    0.090481] s2: Bringing 0uV into 725000-725000uV
[    0.091289] clocksource: Switched to clocksource arch_sys_counter
[    0.091616] l2: Bringing 0uV into 1800000-1800000uV
[    0.091783] qcom_rpm_smd_regulator remoteproc:glink-edge:rpm-requests:regulators: Supply for l2 (l2) resolved to itself
[    0.096103] NET: Registered PF_INET protocol family
[    0.096275] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.097086] tcp_listen_portaddr_hash hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.097122] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.097151] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.097215] TCP bind hash table entries: 4096 (order: 6, 262144 bytes, linear)
[    0.097448] TCP: Hash tables configured (established 4096 bind 4096)
[    0.097705] MPTCP token hash table entries: 512 (order: 2, 24576 bytes, linear)
[    0.097785] UDP hash table entries: 256 (order: 2, 24576 bytes, linear)
[    0.097832] UDP-Lite hash table entries: 256 (order: 2, 24576 bytes, linear)
[    0.098030] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.100374] workingset: timestamp_bits=46 max_order=17 bucket_order=0
[    0.100678] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.100701] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (CMODE_SIZE) (c) 2001-2006 Red Hat, Inc.
[    0.169570] NET: Registered PF_ALG protocol family
[    0.169625] Key type asymmetric registered
[    0.169702] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.169864] io scheduler mq-deadline registered
[    0.169883] io scheduler kyber registered
[    0.169961] io scheduler bfq registered
[    0.171967] qcom-qmp-usb-phy 78000.ssphy: supply vdda-phy not found, using dummy regulator
[    0.172148] qcom-qmp-usb-phy 78000.ssphy: supply vdda-pll not found, using dummy regulator
[    0.174016] qcom-qusb2-phy 79000.qusb: supply vdda-pll not found, using dummy regulator
[    0.174163] qcom-qusb2-phy 79000.qusb: supply vdda-phy-dpdm not found, using dummy regulator
[    0.174376] qcom-qusb2-phy 79000.qusb: Registered Qcom-QUSB2 phy
[    0.185147] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.186668] msm_serial 78b0000.serial: msm_serial: detected port #1
[    0.186733] msm_serial 78b0000.serial: uartclk = 24000000
[    0.187086] 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 22, base_baud = 1500000) is a MSM
[    0.187661] msm_serial 78b1000.serial: msm_serial: detected port #0
[    0.187715] msm_serial 78b1000.serial: uartclk = 1843200
[    0.188063] 78b1000.serial: ttyMSM0 at MMIO 0x78b1000 (irq = 23, base_baud = 115200) is a MSM
[    0.188118] msm_serial: console setup on port #0
[    0.188303] printk: console [ttyMSM0] enabled
[    1.165031] msm_serial: driver initialized
[    1.173491] loop: module loaded
[    1.187433] zram: Added device: zram0
[    1.188966] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xaa
[    1.190103] nand: Macronix MX30UF2G18AC
[    1.196570] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.200105] qcom-nandc 79b0000.nand-controller: Opcode not supported: 238
[    1.207730] Block protection check failed
[    1.214945] 20 fixed-partitions partitions found on MTD device qcom_nand.0
[    1.218584] Creating 20 MTD partitions on "qcom_nand.0":
[    1.225387] 0x000000000000-0x000000180000 : "0:sbl1"
[    1.232682] 0x000000180000-0x000000280000 : "0:mibib"
[    1.237140] 0x000000280000-0x000000600000 : "0:qsee"
[    1.244058] 0x000000600000-0x000000680000 : "0:devcfg"
[    1.246633] 0x000000680000-0x000000700000 : "0:rpm"
[    1.251575] 0x000000700000-0x000000780000 : "0:cdt"
[    1.256323] 0x000000780000-0x000000800000 : "0:appsblenv"
[    1.261264] 0x000000800000-0x000000980000 : "0:appsbl"
[    1.267562] 0x000000980000-0x000000a00000 : "0:art"
[    1.271834] 0x000000a00000-0x000001300000 : "0:wififw"
[    1.283302] 0x000001300000-0x000001380000 : "0:ethphyfw"
[    1.284275] 0x000001380000-0x000001400000 : "u_env"
[    1.288595] 0x000001400000-0x000001440000 : "s_env"
[    1.293026] 0x000001440000-0x000001480000 : "devinfo"
[    1.297652] OF: Bad cell count for /soc@0/nand-controller@79b0000/nand@0/partitions
[    1.302792] 0x000001480000-0x000001c80000 : "kernel"
[    1.316685] 0x000001c80000-0x000006680000 : "rootfs"
[    1.374889] mtd: setting mtd15 (rootfs) as root device
[    1.375199] mtdsplit: no squashfs found in "rootfs"
[    1.378945] 0x000006680000-0x000006e80000 : "alt_kernel"
[    1.390496] 0x000006e80000-0x00000b880000 : "alt_rootfs"
[    1.449066] 0x00000b880000-0x00000ba80000 : "sysdiag"
[    1.451221] 0x00000ba80000-0x00000fe80000 : "syscfg"
[    1.535481] i2c_dev: i2c /dev entries driver
[    1.542503] sdhci: Secure Digital Host Controller Interface driver
[    1.542566] sdhci: Copyright(c) Pierre Ossman
[    1.547628] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.555758] remoteproc remoteproc0: releasing cd00000.remoteproc
[    1.591961] NET: Registered PF_INET6 protocol family
[    1.592906] Segment Routing with IPv6
[    1.596050] In-situ OAM (IOAM) with IPv6
[    1.599654] NET: Registered PF_PACKET protocol family
[    1.603640] Bridge firewalling registered
[    1.608613] 8021q: 802.1Q VLAN Support v1.8
[    1.626268] zswap: loaded using pool zstd/zsmalloc
[    1.633991] Key type encrypted registered
[    1.652440] lrng_drng_mgr: Initial DRNG initialized triggering first seeding
[    1.653793] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[    1.658852] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[    1.665673] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 2
[    1.672249] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[    1.679896] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[    1.687413] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[    1.696538] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      SVS: open-loop= 675000 uV
[    1.703489] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      NOM: open-loop= 787500 uV
[    1.713475] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused    TURBO: open-loop= 850000 uV
[    1.723304] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused   STURBO: open-loop= 900000 uV
[    1.733118] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      SVS: quot[ 7]= 597, quot_offset[ 7]=   0
[    1.742906] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      NOM: quot[ 7]= 800, quot_offset[ 7]= 200
[    1.753753] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused    TURBO: quot[ 7]= 905, quot_offset[ 7]= 105
[    1.764689] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused   STURBO: quot[ 7]= 980, quot_offset[ 7]=  75
[    1.775963] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[    1.779112] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 864000 KHz
[    1.796288] remoteproc remoteproc0: cd00000.remoteproc is available
[    1.804433] ubi0: attaching mtd15
[    1.811401] lrng_es_mgr: LRNG initial entropy level 39 bits of entropy
[    1.820073] lrng_es_mgr: LRNG minimally seeded with 158 bits of entropy
[    1.830822] lrng_es_mgr: LRNG fully operational
[    1.830852] lrng_es_mgr: LRNG fully seeded with 256 bits of entropy
[    2.097208] ubi0: scanning is finished
[    2.116339] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 159 LEBs
[    2.116902] ubi0: attached mtd15 (name "rootfs", size 74 MiB)
[    2.121768] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    2.127599] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    2.134362] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    2.141217] ubi0: good PEBs: 592, bad PEBs: 0, corrupted PEBs: 0
[    2.147983] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    2.154230] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1745590386
[    2.161271] ubi0: available PEBs: 0, total reserved PEBs: 592, PEBs reserved for bad PEB handling: 40
[    2.170569] ubi0: background thread "ubi_bgt0d" started, PID 692
[    2.171559] block ubiblock0_0: created from ubi0:0(root▒[    2.193611] ------------[ cut here ]------------
[    2.193647] usb0_gdsc status stuck at 'on'
[    2.193681] WARNING: CPU: 2 PID: 666 at drivers/clk/qcom/gdsc.c:178 0xffffffc080633084
[    2.201204] Modules linked in:
[    2.209093] CPU: 2 PID: 666 Comm: kworker/2:2 Not tainted 6.6.87 #0
[    2.212136] Hardware name: Linksys MR7350 (DT)
[    2.218298] Workqueue: pm 0xffffffc0806eda4c
[    2.222811] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[    2.227243] pc : 0xffffffc080633084
[    2.233918] lr : 0xffffffc080633084
[    2.237391] sp : ffffffc081f93c80
[    2.240863] x29: ffffffc081f93c80 x28: 00000000000001c8 x27: 000000007fffffff
[    2.244343] x26: 61c8864680b583eb x25: ffffff8002069605 x24: ffffffc080ef3948
[    2.251462] x23: 0000000000000000 x22: 000000000016e35f x21: 00000000827710f9
[    2.258580] x20: ffffffc081f93ccc x19: ffffffc080ef3480 x18: ffffffc080e60000
[    2.265698] x17: 0000000000000058 x16: 0000000000000001 x15: ffffffc080e60c08
[    2.272816] x14: ffffffc080ca1000 x13: ffffffc080e60c08 x12: c0000000ffffefff
[    2.279933] x11: ffffffc080e60b88 x10: c0000000ffffefff x9 : 0000000000000fff
[    2.287051] x8 : 00000000ffffefff x7 : ffffffc080e60d98 x6 : ffffffc080e60bf0
[    2.294170] x5 : ffffffc080eb8d98 x4 : 0000000000017fe8 x3 : 000000000000000c
[    2.301288] x2 : 0000000000000fff x1 : 0000000000001000 x0 : 000000000000001e
[    2.308406] Call trace:
[    2.315514]  0xffffffc080633084
[    2.317773]  0xffffffc0806333f0
[    2.320898]  0xffffffc0806ed5c0
[    2.324023]  0xffffffc0806eda7c
[    2.327147]  0xffffffc080076fe8
[    2.330272]  0xffffffc08007796c
[    2.333398]  0xffffffc0800828f8
[    2.336521]  0xffffffc080013a64
[    2.339648] ---[ end trace 0000000000000000 ]---
[    2.349493] VFS: Mounted root (squashfs filesystem) readonly on device 253:0.
[    2.350127] Freeing unused kernel memory: 1216K
[    2.355816] Run /sbin/init as init process
[    2.548285] init: Console is alive
[    2.548481] init: - watchdog -
[    3.614047] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.644020] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: [email protected]
[    3.679448] JFS: nTxBlock = 2995, nTxLock = 23962
[    3.718585] SGI XFS with ACLs, security attributes, no debug enabled
[    3.720860] gpio_button_hotplug: loading out-of-tree module taints kernel.
[    3.770440] ssdk_dt_parse_interrupt[941]:INFO:intr-gpio does not exist
[    4.179717] __adpt_hppe_uniphy_psgmii_mode_set[1194]:INFO:uniphy 0 psgmii channel selection
[    4.305442] regi_init[2525]:INFO:Initializing CPPE Done!!
[    4.305557] regi_init[2574]:INFO:qca-ssdk module init succeeded!
[    4.312615] EDMA ver 1 hw init
[    4.316195] EDMA HW Reset completed succesfully
[    4.318810] Num rings - TxDesc:1 (23-23) TxCmpl:1 (23-23)
[    4.323203] RxDesc:1 (15-15) RxFill:1 (7-7)
[    4.485053] Qualcomm QCA8075 90000.mdio-1:00: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:00, irq=POLL)
[    4.556133] Qualcomm QCA8075 90000.mdio-1:01: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:01, irq=POLL)
[    4.628133] Qualcomm QCA8075 90000.mdio-1:02: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:02, irq=POLL)
[    4.700045] Qualcomm QCA8075 90000.mdio-1:03: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:03, irq=POLL)
[    4.772015] Qualcomm QCA8075 90000.mdio-1:04: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:04, irq=POLL)
[    4.773127] **********************************************************
[    4.780966] * NSS Data Plane driver
[    4.787437] **********************************************************
[    4.807327] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    4.807393] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
[    4.812643] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000008000000010
[    4.819332] xhci-hcd xhci-hcd.1.auto: irq 39, io mem 0x08a00000
[    4.828790] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    4.834550] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
[    4.840124] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[    4.848165] hub 1-0:1.0: USB hub found
[    4.854386] hub 1-0:1.0: 1 port detected
[    4.875774] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.876348] hub 2-0:1.0: USB hub found
[    4.883014] hub 2-0:1.0: 1 port detected
[    4.944845] usbcore: registered new interface driver usb-storage
[    4.946467] usbcore: registered new interface driver uas
[    4.950419] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.963890] init: - preinit -
[    5.227330] usb 1-1: new high-speed USB device number 2 using xhci-hcd
Cannot parse config file '/etc/fw_env.config': No such file or directory
Failed to find NVMEM device
[    5.520191] hub 1-1:1.0: USB hub found
[    5.520588] hub 1-1:1.0: 4 ports detected
[    5.653740] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[    5.712551] hub 2-1:1.0: USB hub found
[    5.712983] hub 2-1:1.0: 4 ports detected
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    6.011302] usb 1-1.1: new high-speed USB device number 3 using xhci-hcd
[    7.043454] usb 2-1.4: new SuperSpeed USB device number 3 using xhci-hcd
[    7.104354] hub 2-1.4:1.0: USB hub found
[    7.104727] hub 2-1.4:1.0: 4 ports detected
[    7.219307] usb 1-1.2: new high-speed USB device number 4 using xhci-hcd
[    8.259370] usb 2-1.1: new SuperSpeed USB device number 4 using xhci-hcd
[    8.296740] scsi host0: uas
[    8.298043] scsi 0:0:0:0: Direct-Access     TOSHIBA  DT01ACA200       0515 PQ: 0 ANSI: 6
[    8.301856] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    9.331368] usb 2-1.2: new SuperSpeed USB device number 5 using xhci-hcd
[    9.368929] scsi host1: uas
[    9.370177] scsi 1:0:0:0: Direct-Access     TOSHIBA  DT01ACA300       0515 PQ: 0 ANSI: 6
[    9.374073] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    9.507309] usb 1-1.4: new high-speed USB device number 6 using xhci-hcd
[    9.744025] hub 1-1.4:1.0: USB hub found
[    9.744360] hub 1-1.4:1.0: 4 ports detected
[    9.875414] usb 2-1.3: new SuperSpeed USB device number 6 using xhci-hcd
[    9.913160] scsi host2: uas
[    9.914575] scsi 2:0:0:0: Direct-Access     WDC WD10 EARX-00N0YB0     0515 PQ: 0 ANSI: 6
[    9.918425] sd 2:0:0:0: Attached scsi generic sg2 type 0
[    9.926168] mount_root: loading kmods from internal overlay
[    9.950327] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[    9.952212] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   10.037240] block: attempting to load /tmp/overlay/upper/etc/config/fstab
[   10.037424] block: unable to load configuration (fstab: Entry not found)
[   10.043100] block: attempting to load /tmp/overlay/etc/config/fstab
[   10.050039] block: unable to load configuration (fstab: Entry not found)
[   10.055931] block: attempting to load /etc/config/fstab
[   10.063135] block: unable to load configuration (fstab: Entry not found)
[   10.067886] block: no usable configuration
[   10.083774] UBIFS (ubi0:1): default file-system created
[   10.084261] UBIFS (ubi0:1): Mounting in unauthenticated mode
[   10.087917] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 1050
[   10.141124] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   10.141184] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   10.147984] UBIFS (ubi0:1): FS size: 18919424 bytes (18 MiB, 149 LEBs), max 159 LEBs, journal size 1015809 bytes (0 MiB, 7 LEBs)
[   10.157881] UBIFS (ubi0:1): reserved for root: 893610 bytes (872 KiB)
[   10.169483] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 6CE64AA1-3388-4E32-9EA3-2DDC42E12F0C, small LPT model
[   10.176515] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   10.187243] block: unable to load configuration (fstab: Entry not found)
[   10.193917] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[   10.200877] block: unable to load configuration (fstab: Entry not found)
[   10.207192] block: attempting to load /etc/config/fstab
[   10.213978] block: unable to load configuration (fstab: Entry not found)
[   10.218901] block: no usable configuration
[   10.228347] UBIFS (ubi0:1): un-mount UBI device 0
[   10.229726] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[   10.237815] UBIFS (ubi0:1): Mounting in unauthenticated mode
[   10.240707] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 1053
[   10.293820] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   10.293881] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   10.300695] UBIFS (ubi0:1): FS size: 18919424 bytes (18 MiB, 149 LEBs), max 159 LEBs, journal size 1015809 bytes (0 MiB, 7 LEBs)
[   10.310577] UBIFS (ubi0:1): reserved for root: 893610 bytes (872 KiB)
[   10.322179] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 6CE64AA1-3388-4E32-9EA3-2DDC42E12F0C, small LPT model
[   10.354582] block: attempting to load /tmp/overlay/upper/etc/config/fstab
[   10.354743] block: unable to load configuration (fstab: Entry not found)
[   10.360459] block: attempting to load /tmp/overlay/etc/config/fstab
[   10.367234] block: unable to load configuration (fstab: Entry not found)
[   10.373182] block: attempting to load /etc/config/fstab
[   10.380173] block: unable to load configuration (fstab: Entry not found)
[   10.385063] block: no usable configuration
[   10.393404] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   10.396054] block: unable to load configuration (fstab: Entry not found)
[   10.402762] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[   10.409871] block: unable to load configuration (fstab: Entry not found)
[   10.416065] block: attempting to load /etc/config/fstab
[   10.422857] block: unable to load configuration (fstab: Entry not found)
[   10.427766] block: no usable configuration
[   10.436124] mount_root: overlay filesystem has not been fully initialized yet
[   10.438907] mount_root: switching to ubifs overlay
[   10.448450] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[   10.471356] procd: - early -
[   10.471488] procd: - watchdog -
[   11.040244] procd: - watchdog -
[   11.057534] procd: - ubus -
[   11.110328] procd: - init -
Please press Enter to activate this console.
[   11.431794] kmodloader: loading kernel modules from /etc/modules.d/*
[   11.602774] I/O scheduler: non-rotational device 'mtdblock16' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   11.754626] I/O scheduler: non-rotational device 'loop1' was '[none] mq-deadline kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   11.874275] I/O scheduler: non-rotational device 'mtdblock8' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   12.018693] I/O scheduler: non-rotational device 'nbd3' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   12.130711] I/O scheduler: non-rotational device 'nbd15' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   12.250399] I/O scheduler: non-rotational device 'mtdblock14' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   12.355063] I/O scheduler: non-rotational device 'mtdblock6' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   12.474505] I/O scheduler: non-rotational device 'nbd1' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   12.586857] I/O scheduler: non-rotational device 'nbd13' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   12.674316] I/O scheduler: non-rotational device 'mtdblock12' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   12.699350] usb 1-1.4.1: new low-speed USB device number 7 using xhci-hcd
[   12.842438] I/O scheduler: non-rotational device 'mtdblock4' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   12.884783] sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[   12.895988] sd 2:0:0:0: [sdc] 4096-byte physical blocks
[   12.903596] sd 2:0:0:0: [sdc] Write Protect is off
[   12.909012] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   13.026542] I/O scheduler: non-rotational device 'loop6' was '[none] mq-deadline kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   13.035628] sd 2:0:0:0: [sdc] Preferred minimum I/O size 4096 bytes
[   13.046381] sd 2:0:0:0: [sdc] Optimal transfer size 33553920 bytes not a multiple of preferred minimum block size (4096 bytes)
[   13.095086]  sdc: sdc1 sdc2
[   13.095527] sd 2:0:0:0: [sdc] Attached SCSI disk
[   13.162684] I/O scheduler: non-rotational device 'nbd11' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   13.482295] I/O scheduler: non-rotational device 'mtdblock10' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   13.618583] I/O scheduler: non-rotational device 'mtdblock2' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   13.755132] I/O scheduler: non-rotational device 'nbd8' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   13.914426] I/O scheduler: non-rotational device 'mtdblock19' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   14.090521] I/O scheduler: non-rotational device 'loop4' was '[none] mq-deadline kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   14.218651] I/O scheduler: non-rotational device 'mtdblock0' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   14.346683] I/O scheduler: non-rotational device 'nbd6' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   14.490739] I/O scheduler: non-rotational device 'mtdblock17' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   14.650473] I/O scheduler: non-rotational device 'loop2' was '[none] mq-deadline kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   14.802524] I/O scheduler: non-rotational device 'mtdblock9' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   14.938316] I/O scheduler: non-rotational device 'nbd4' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   15.082777] I/O scheduler: non-rotational device 'mtdblock15' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   15.242241] I/O scheduler: non-rotational device 'loop0' was '[none] mq-deadline kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   15.402738] I/O scheduler: non-rotational device 'mtdblock7' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   15.514754] I/O scheduler: non-rotational device 'nbd2' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   15.642555] I/O scheduler: non-rotational device 'nbd14' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   15.682141] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[   15.692896] sd 0:0:0:0: [sda] 4096-byte physical blocks
[   15.700908] sd 0:0:0:0: [sda] Write Protect is off
[   15.706036] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   15.786482] I/O scheduler: non-rotational device 'mtdblock13' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   15.811637] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[   15.822673] sd 0:0:0:0: [sda] Optimal transfer size 33553920 bytes not a multiple of preferred minimum block size (4096 bytes)
[   15.831176] sd 0:0:0:0: [sda] Attached SCSI disk
[   16.058562] I/O scheduler: non-rotational device 'mtdblock5' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   16.242624] I/O scheduler: non-rotational device 'loop7' was '[none] mq-deadline kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   16.386697] I/O scheduler: non-rotational device 'nbd0' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   16.546585] I/O scheduler: non-rotational device 'nbd12' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   16.643870] usb 1-1.4.1: USB disconnect, device number 7
[   16.666463] I/O scheduler: non-rotational device 'mtdblock11' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   16.794695] I/O scheduler: non-rotational device 'mtdblock3' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   16.922473] I/O scheduler: non-rotational device 'nbd9' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   17.194550] I/O scheduler: non-rotational device 'loop5' was '[none] mq-deadline kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   17.314615] I/O scheduler: non-rotational device 'nbd10' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   17.442584] I/O scheduler: non-rotational device 'mtdblock1' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   17.578496] I/O scheduler: non-rotational device 'nbd7' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   17.706342] I/O scheduler: non-rotational device 'mtdblock18' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   17.866499] I/O scheduler: non-rotational device 'loop3' was '[none] mq-deadline kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   18.010598] I/O scheduler: non-rotational device 'ubiblock0_0' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   18.130553] I/O scheduler: non-rotational device 'nbd5' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   18.898791] I/O scheduler: non-rotational device 'sdc' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   18.971910] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[   18.982289] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[   18.990537] sd 1:0:0:0: [sdb] Write Protect is off
[   18.995631] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   19.091751] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes
[   19.091816] sd 1:0:0:0: [sdb] Optimal transfer size 33553920 bytes not a multiple of preferred minimum block size (4096 bytes)
[   19.098973] sd 1:0:0:0: [sdb] Attached SCSI disk
[   19.178827] Key type dns_resolver registered
[   19.193287] Key type cifs.idmap registered
[   19.198908] tun: Universal TUN/TAP device driver, 1.6
[   19.218975] ffffff80022ccc00: of_address_to_resource() return error for nss_misc_reset
[   19.219030] NSS HAL common init failed
[   19.219033] qca-nss: probe of soc@0:nss@40000000 failed with error -14
[   19.231951] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[   19.239157] nat46: module (version b42c37d5c6dee4593df0fc60b37bc7ec4ee243a4) loaded.
[   19.242425] I/O scheduler: non-rotational device 'sda' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   19.258629] QCA multicast snooping installed successfully
[   19.281629] Jool: Core Jool v4.1.13.0 module inserted.
[   19.282564] NAT64 Jool v4.1.13.0 module inserted.
[   19.286493] SIIT Jool v4.1.13.0 module inserted.
[   19.313109] cryptodev: driver 1.14 loaded.
[   19.315148] nss_vlan_mgr_init_module[1940]:Module (Build Build Id: 04/26/25, 09:00:04) loaded
[   19.322427] nss_wifi_meshmgr_init_module[1994]:Module Build Id: 04/26/25, 09:00:08 loaded
[   19.326660] nss-macsec0 DT exist!
[   19.333218] nss_macsec init success
[   19.342484] hid: raw HID events driver (C) Jiri Kosina
[   19.343860] GACT probability on
[   19.347596] Mirror/redirect action on
[   19.355134] u32 classifier
[   19.355175]     input device check on
[   19.356828]     Actions configured
[   19.371935] ntfs3: Enabled Linux POSIX ACLs support
[   19.376797] fuse: init (API version 7.39)
[   19.394834] usbcore: registered new interface driver cdc_wdm
[   19.396877] Loading modules backported from Linux version v6.12.6-0-ge9d65b48ce1a
[   19.399583] Backport generated by backports.git v6.1.110-1-35-g410656ef04d2
[   19.574021] <NSS-CRYPTO>:module loaded Build_ID - 04/26/25, 08:57:50 SoC=ipq60xx
[   19.577919] NET: Registered PF_QIPCRTR protocol family
[   19.580757] usb 1-1.4.1: new low-speed USB device number 8 using xhci-hcd
[   19.598396] usbcore: registered new interface driver ums-alauda
[   19.599831] usbcore: registered new interface driver ums-cypress
[   19.604805] usbcore: registered new interface driver ums-datafab
[   19.611015] usbcore: registered new interface driver ums-freecom
[   19.617431] usbcore: registered new interface driver ums-isd200
[   19.623596] usbcore: registered new interface driver ums-jumpshot
[   19.629060] usbcore: registered new interface driver ums-karma
[   19.635681] usbcore: registered new interface driver ums-sddr09
[   19.640909] usbcore: registered new interface driver ums-sddr55
[   19.646900] usbcore: registered new interface driver ums-usbat
[   19.653510] usbcore: registered new interface driver usbhid
[   19.656616] usbhid: USB HID core driver
[   19.663526] usbcore: registered new interface driver usblp
[   19.673085] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[   19.673137] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <[email protected]>. All Rights Reserved.
[   19.711739] xt_time: kernel timezone is -0000
[   19.713633] usbcore: registered new interface driver cdc_ether
[   19.717595] usbcore: registered new interface driver cdc_ncm
[   19.802796] usbcore: registered new interface driver rndis_host
[   19.826174] ath11k c000000.wifi: ipq6018 hw1.0
[   19.826227] ath11k c000000.wifi: FW memory mode: 1
[   19.866424] hid-generic 0003:0D9F:0004.0001: hiddev96,hidraw0: USB HID v1.00 Device [POWERCOM Co.,LTD HID UPS Battery] on usb-xhci-hcd.1.auto-1.4.1/input0
[   20.058390] I/O scheduler: non-rotational device 'sdb' was 'none [mq-deadline] kyber bfq ', now 'none mq-deadline [kyber] bfq '
[   20.746498] remoteproc remoteproc0: powering up cd00000.remoteproc
[   20.772184] remoteproc remoteproc0: Booting fw image IPQ6018/q6_fw.mdt, size 7340
[   21.423346] remoteproc remoteproc0: remote processor cd00000.remoteproc is now up
[   21.427522] kmodloader: done loading kernel modules from /etc/modules.d/*
[   21.467359] ath11k c000000.wifi: qmi fail to get qcom,m3-dump-addr, ignore m3 dump mem req
[   21.475513] ath11k c000000.wifi: chip_id 0x0 chip_family 0x4 board_id 0xff soc_id 0xffffffff
[   21.475573] ath11k c000000.wifi: fw_version 0x2c0205b4 fw_build_timestamp 2024-10-04 16:15 fw_build_id WLAN.HK.2.12-01460-QCAHKSWPL_SILICONZ-1
[   21.494614] ath11k c000000.wifi: bdf template revision v1.2.3, boardrev 39, patch to v1.4.3
[   21.495761] ath11k c000000.wifi: maximum calibrated power 25.5 dbm
[   21.894187] ath11k c000000.wifi: htt event 48 not handled
[   21.899607] ath11k c000000.wifi: nss init soc nss if_num 203 userpd_id 0
[   21.899672] ath11k c000000.wifi: nss state in default init state
[   21.905530] ath11k c000000.wifi: NSS SOC Initialization Failed :-22
[   21.911413] ath11k c000000.wifi: failed to setup nss driver interface-22
[   21.920000] ath11k c000000.wifi: failed to create pdev core: -22
[   23.556402] usb 1-1.4.1: USB disconnect, device number 8
[   26.467372] usb 1-1.4.1: new low-speed USB device number 9 using xhci-hcd
[   26.748627] hid-generic 0003:0D9F:0004.0002: hiddev96,hidraw0: USB HID v1.00 Device [POWERCOM Co.,LTD HID UPS Battery] on usb-xhci-hcd.1.auto-1.4.1/input0
[   27.720738] zram0: detected capacity change from 0 to 766800
[   27.733757] Adding 383396k swap on /dev/zram0.  Priority:100 extents:1 across:383396k SSDsc
[   29.896663] ECM init
[   29.896746] ECM database jhash random seed: 0xd9d1d3a6
[   29.908550] br-lan: port 1(lan1) entered blocking state
[   29.908605] br-lan: port 1(lan1) entered disabled state
[   29.912652] nss-dp 3a001000.dp1 lan1: entered allmulticast mode
[   29.918142] nss-dp 3a001000.dp1 lan1: entered promiscuous mode
[   29.932158] br-lan: port 2(lan2) entered blocking state
[   29.932220] br-lan: port 2(lan2) entered disabled state
[   29.936250] nss-dp 3a001200.dp2 lan2: entered allmulticast mode
[   29.941789] nss-dp 3a001200.dp2 lan2: entered promiscuous mode
[   29.952706] br-lan: port 3(lan3) entered blocking state
[   29.953233] br-lan: port 3(lan3) entered disabled state
[   29.958495] nss-dp 3a001400.dp3 lan3: entered allmulticast mode
[   29.963845] nss-dp 3a001400.dp3 lan3: entered promiscuous mode
[   29.974439] br-lan: port 4(lan4) entered blocking state
[   29.975369] br-lan: port 4(lan4) entered disabled state
[   29.979813] ECM init complete
[   29.980553] nss-dp 3a001600.dp4 lan4: entered allmulticast mode
[   29.989071] nss-dp 3a001600.dp4 lan4: entered promiscuous mode
[   30.469451] usb 1-1.4.1: USB disconnect, device number 9
[   32.028261] nss-dp 3a001400.dp3 lan3: PHY Link up speed: 100
[   32.028365] br-lan: port 3(lan3) entered blocking state
[   32.033016] br-lan: port 3(lan3) entered forwarding state
[   32.219313] ath11k c000000.wifi: failed to wait wlan mode request (mode 4): -110
[   32.219377] ath11k c000000.wifi: qmi failed to send wlan mode off: -110
[   32.987872] nss-dp 3a001200.dp2 lan2: PHY Link up speed: 1000
[   32.987939] br-lan: port 2(lan2) entered blocking state
[   32.992616] br-lan: port 2(lan2) entered forwarding state
[   33.052032] nss-dp 3a001800.dp5 wan: PHY Link up speed: 1000
[   33.363351] usb 1-1.4.1: new low-speed USB device number 10 using xhci-hcd
[   33.657983] hid-generic 0003:0D9F:0004.0003: hiddev96,hidraw0: USB HID v1.00 Device [POWERCOM Co.,LTD HID UPS Battery] on usb-xhci-hcd.1.auto-1.4.1/input0
[   34.075949] nss-dp 3a001600.dp4 lan4: PHY Link up speed: 1000
[   34.076036] br-lan: port 4(lan4) entered blocking state
[   34.080753] br-lan: port 4(lan4) entered forwarding state
[   36.367685] ksmbd: kill command received
[   36.662540] ksmbd: kill command received
[   37.381797] usb 1-1.4.1: USB disconnect, device number 10
[   37.628780] qcom-q6-mpd cd00000.remoteproc: fatal error received:
[   37.628780] QC Image Version: QC_IMAGE_VERSION_STRING=WLAN.HK.2.12-01460-QCAHKSWPL_SILICONZ-1
[   37.628780] Image Variant : IMAGE_VARIANT_STRING=6018.wlanfw.evalQ
[   37.628780]
[   37.628780] dog_hb.c:210 DOG_HB detects starvation of task "WLAN_TQM", triage with its owner(d.dump 0x4afe2510)
[   37.628780] param0 :1258169616, param1 :1258169616, param2 :zero.
[   37.628780] Thread ID      : 0x00000077  Thread name    : dog_hb  Process ID     : 0
[   37.628780] Register:
[   37.628780] SP : 0x4afc2ac0
[   37.628780] FP : 0x4afc2ac8
[   37.628780] PC : 0x4ac07f9c
[   37.628780] SSR : 0x00000008
[   37.628780] BADVA : 0x00020000
[   37.628780] LR : 0x4ac07738
[   37.628780]
[   37.628780] Stack Dump
[   37.628780] from : 0x4afc2ac0
[   37.628780] to   : 0x4afc2c00
[   37.628780]
[   37.683094] remoteproc remoteproc0: crash detected in cd00000.remoteproc: type fatal error
[   37.704966] remoteproc remoteproc0: handling crash #1 in cd00000.remoteproc
[   37.712875] remoteproc remoteproc0: recovering cd00000.remoteproc

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.XF.0.3-00077-IPQ60xxLZB-2
S - IMAGE_VARIANT_STRING=IPQ6018LA
S - OEM_IMAGE_VERSION_STRING=crm-ubuntu64
S - Boot Interface: NAND
S - Secure Boot: Off
S - Boot Config @ 0x000a602c = 0x000002e5
S - JTAG ID @ 0x000a607c = 0x001390e1
S - OEM ID @ 0x000a6080 = 0x00000000
S - Serial Number @ 0x000a4128 = 0xcb4a3f56
S - OEM Config Row 0 @ 0x000a4188 = 0x0000000000000000
S - OEM Config Row 1 @ 0x000a4190 = 0x0000000000000000
S - Feature Config Row 0 @ 0x000a4130 = 0x0000800018200021
S - Feature Config Row 1 @ 0x000a4138 = 0x02c3e83783000009
S - PBL Patch Ver: 1
S - I-cache: On
S - D-cache: On
B -      3413 - PBL, Start
B -       592 - bootable_media_detect_entry, Start
B -      4339 - bootable_media_detect_success, Start
B -      5147 - elf_loader_entry, Start
B -      5319 - auth_hash_seg_entry, Start
B -      7786 - auth_hash_seg_exit, Start
B -      8281 - elf_segs_hash_verify_entry, Start
B -    110458 - elf_segs_hash_verify_exit, Start
B -    114881 - auth_xbl_sec_hash_seg_entry, Start
B -    115025 - auth_xbl_sec_hash_seg_exit, Start
B -    121579 - xbl_sec_segs_hash_verify_entry, Start
B -    121580 - xbl_sec_segs_hash_verify_exit, Start
B -    122509 - PBL, End
B -    103303 - SBL1, Start
B -    243359 - GCC [RstStat:0x2, RstDbg:0x420100] WDog Stat : 0x4
B -    245830 - clock_init, Start
D -      2867 - clock_init, Delta
B -    254400 - boot_flash_init, Start
D -     26199 - boot_flash_init, Delta
B -    283741 - sbl1_ddr_set_default_params, Start
D -       244 - sbl1_ddr_set_default_params, Delta
B -    290360 - boot_config_data_table_init, Start
D -      4758 - boot_config_data_table_init, Delta - (575 Bytes)
B -    300211 - CDT Version:2,Platform ID:8,Major ID:3,Minor ID:2,Subtype:0
B -    305061 - Image Load, Start
D -      6588 - OEM_MISC Image Loaded, Delta - (0 Bytes)
B -    314394 - Image Load, Start
D -      5063 - PMIC Image Loaded, Delta - (0 Bytes)
B -    322263 - sbl1_ddr_set_params, Start
B -    327234 - CPR configuration: 0x366
B -    330437 - Pre_DDR_clock_init, Start
D -       213 - Pre_DDR_clock_init, Delta
D -         0 - sbl1_ddr_set_params, Delta