This is write up is on how to port forward over wireguard. I am going to be port forwarding a mail server running MailCow on my local server, but really any service can be port forwared with some modifications to the IPTables commands in the wireguard file.
I am using a cheap Vultr VPS as my proxy server, if your intrested heres a referral link https://www.vultr.com/?ref=9019507 where I get $10 or if you plan to spend more then $35 on your account you will get $100 and I will get $35 https://www.vultr.com/?ref=9019508-8H
- Debain 10 Buster
- Tunnel subnet: 10.1.1.0
- Proxy-VPS Tunnel IP: 10.1.1.1
- Peer [Mail Server] Tunnel IP: 10.1.1.2
I installed WireGuard using this script: https://github.com/angristan/wireguard-install
Had an error used to fix: https://stackoverflow.com/a/66745279
Allow wireguard on port 51820(make sure the port is correct, the script assign's a random port): E.g.
sudo ufw allow 51820/udp
Start the WireGuard service at boot time using the systemctl command, run:
sudo systemctl enable wg-quick@wg0- Destination NAT(DNAT) only rewrites the destination IP address, this should be used for incoming trafic headed to a peer.
- Source NAT(SNAT) rewrites the source IP address to and should happen automatically for outbound traffic that passes through the Wg Tunnel.
Services Port Forwarded
- Http on port 80
- Https on port 443
- Postfix SMTP on port 25
- Postfix SMTPS on port 465
- Postfix Submission on port 587
- Dovecot IMAP on port 143
- Dovecot IMAPS on port 993
- Dovecot POP3 on port 110
- Dovecot POP3S on port 995
- Dovecot ManageSieve on port 4190
Also add ufw for each port on Proxy-VPS E.g. sudo ufw allow 25/tcp
Run and find the WAN interface name and replace enp1s0 blow to the correct interface name we want the portforward to listen on
ip addr Place in /etc/wireguard/wg0.conf on Proxy-VPS just above [Peer]
### Http on port 80
PostUp = iptables -t nat -A PREROUTING -p tcp -i enp1s0 --dport 80 -j DNAT --to-destination 10.1.1.2:80
PostDown = iptables -t nat -D PREROUTING -p tcp -i enp1s0 --dport 80 -j DNAT --to-destination 10.1.1.2:80
### Https on port 443
PostUp = iptables -t nat -A PREROUTING -p tcp -i enp1s0 --dport 443 -j DNAT --to-destination 10.1.1.2:443
PostDown = iptables -t nat -D PREROUTING -p tcp -i enp1s0 --dport 443 -j DNAT --to-destination 10.1.1.2:443
### Postfix SMTP on port 25
PostUp = iptables -t nat -A PREROUTING -p tcp -i enp1s0 --dport 25 -j DNAT --to-destination 10.1.1.2:25
PostDown = iptables -t nat -D PREROUTING -p tcp -i enp1s0 --dport 25 -j DNAT --to-destination 10.1.1.2:25
### Postfix SMTPS on port 465
PostUp = iptables -t nat -A PREROUTING -p tcp -i enp1s0 --dport 465 -j DNAT --to-destination 10.1.1.2:465
PostDown = iptables -t nat -D PREROUTING -p tcp -i enp1s0 --dport 465 -j DNAT --to-destination 10.1.1.2:465
### Postfix Submission on port 587
PostUp = iptables -t nat -A PREROUTING -p tcp -i enp1s0 --dport 587 -j DNAT --to-destination 10.1.1.2:587
PostDown = iptables -t nat -D PREROUTING -p tcp -i enp1s0 --dport 587 -j DNAT --to-destination 10.1.1.2:587
### Dovecot IMAP on port 143
PostUp = iptables -t nat -A PREROUTING -p tcp -i enp1s0 --dport 143 -j DNAT --to-destination 10.1.1.2:143
PostDown = iptables -t nat -D PREROUTING -p tcp -i enp1s0 --dport 143 -j DNAT --to-destination 10.1.1.2:143
### Dovecot IMAPS on port 993
PostUp = iptables -t nat -A PREROUTING -p tcp -i enp1s0 --dport 993 -j DNAT --to-destination 10.1.1.2:993
PostDown = iptables -t nat -D PREROUTING -p tcp -i enp1s0 --dport 993 -j DNAT --to-destination 10.1.1.2:993
### Dovecot POP3 on port 110
PostUp = iptables -t nat -A PREROUTING -p tcp -i enp1s0 --dport 110 -j DNAT --to-destination 10.1.1.2:110
PostDown = iptables -t nat -D PREROUTING -p tcp -i enp1s0 --dport 110 -j DNAT --to-destination 10.1.1.2:110
### Dovecot POP3S on port 995
PostUp = iptables -t nat -A PREROUTING -p tcp -i enp1s0 --dport 995 -j DNAT --to-destination 10.1.1.2:995
PostDown = iptables -t nat -D PREROUTING -p tcp -i enp1s0 --dport 995 -j DNAT --to-destination 10.1.1.2:995
### Dovecot ManageSieve on port 4190
PostUp = iptables -t nat -A PREROUTING -p tcp -i enp1s0 --dport 4190 -j DNAT --to-destination 10.1.1.2:4190
PostDown = iptables -t nat -D PREROUTING -p tcp -i enp1s0 --dport 4190 -j DNAT --to-destination 10.1.1.2:4190
sudo apt install wireguardTransfer the file created by the script from the remote VPS to /etc/wireguard/wg0.conf
On the local machine we kept encountering an issue where the tunnel would die after several minutes, once the handshake connection expired. To fix this I added
PersistentKeepAlive = 25to the bottom of the wg0.conf file
I left
AllowedIPs = 0.0.0.0/0to forward all traffic of all my mail server through the remote VPS IP address, due to it needing to send outgoing SMTP email through the NAT masquerade as the remote IP instead of my home networks IP
Start the WireGuard service at boot time using the systemctl command, run:
sudo systemctl enable wg-quick@wg0Start WireGuard the tunnel:
sudo wg-quick up wg0
@GildedHonour Yes
My purpose is my isp blocks port 25(smtp) and I cant reverse DNS my IP address as it is a residential connection.
My local server is running 24/7 on a UPS with only a few minutes of down time a year, so it makes more sense for me to use it for email hosting then paying for a equivalent dedicated server.