davinci1.0a

config.ini

# generated by Slic3r 1.3.1-dev on 
adaptive_slicing = 0
adaptive_slicing_quality = 75%
avoid_crossing_perimeters = 0
bed_shape = 0x0,200x0,200x200,0x200
bed_temperature = 80
before_layer_gcode = 
between_objects_gcode = 
bottom_infill_pattern = rectilinear
bottom_solid_layers = 5
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_connections_width = 0
brim_width = 0
compatible_printers = 
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 1
dont_support_bridges = 1
duplicate_distance = 6
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
end_gcode = M117 Done\nG92 E0 ; reset extrusion distance\nM104 S0 ; turn off extruder\nM140 S0 ; turn off Bed\nG90 ; Absolute\nG28 X0 Y0 ; home\nM117 Down Bed\nG1 Z200 ; Lower bed\nM117 Cleaning\nM100 ; Cleaning\nM84 ; Disable motors\nM117 Cooling\nM190 S55 ; Bed (cooling)\n; M116 ; Wait for all temperatures\nM140 S0 ; turn off Bed\nM117 Pickup piece\nM300 s2500 p400 ; Beep\nM300 s2000 p400\nM300 s1500 p400\nM300 s1000 p400\nM84 ; Disable motors\nM117 Printer ready\n
external_perimeter_extrusion_width = 0
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 0
filament_notes = ""
filament_settings_id = 
fill_angle = 45
fill_density = 40%
fill_gaps = 1
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 100
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 30%
first_layer_temperature = 230
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
has_heatbed = 1
host_type = octoprint
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 55%
infill_speed = 60
interface_shells = 0
interior_brim_width = 0
label_printed_objects = 0
layer_gcode = 
layer_height = 0.2
match_horizontal_surfaces = 0
max_fan_speed = 100
max_layer_height = 0.3
max_print_speed = 80
max_volumetric_speed = 0
min_fan_speed = 35
min_layer_height = 0.15
min_print_speed = 10
min_shell_thickness = 0
min_skirt_length = 0
min_top_bottom_shell_thickness = 0
notes = 
nozzle_diameter = 0.4
octoprint_apikey = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base]_slic3r.gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 2
post_process = C:/3dprint_scripts/daVinciGcodePrep.py
pressure_advance = 0
print_host = 
print_settings_id = 
printer_notes = 
printer_settings_id = 
raft_layers = 0
regions_overlap = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
seam_position = aligned
sequential_print_priority = 0
serial_port = 
serial_speed = 250000
shortcuts = support_material
skirt_distance = 15
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 30
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
start_filament_gcode = "; Filament gcode\n"
start_gcode = M140 S[first_layer_bed_temperature] ; Bed (no wait)\nM104 S[first_layer_temperature] ; Extruder (no wait)\nM106 S255 ; Start fan\nG90 ; set absolute coordinates\nG28 ; home all axis\nM190 S[first_layer_bed_temperature] ; Bed (wait)\nM109 S[first_layer_temperature] ; Extruder (wait)\nM117 Start\nM300 s1000 p400 ; Beep\nM300 s1500 p400\nM300 s2000 p400\nM300 s2500 p400\nM117 Cleaning\nM100 ; Cleaning\nG1 Z5 F1500\nG1 X0 Y10 F1000\nG1 X5 Y35 F1000\nG92 E0 ; reset extrusion distance\nG1 Z[first_layer_height] F4800.000\nG1 X5 Y175 E14 F1000\nG1 X5 Y190 F1000\nM117 Printing
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_extrusion_width = 0
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_max_layers = 0
support_material_pattern = honeycomb
support_material_pillar_size = 2.5
support_material_pillar_spacing = 10
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 60%
temperature = 220
thin_walls = 1
threads = 1
toolchange_gcode = 
top_infill_extrusion_width = 0
top_infill_pattern = rectilinear
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 100
use_firmware_retraction = 0
use_relative_e_distances = 0
use_set_and_wait_bed = 0
use_set_and_wait_extruder = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
xy_size_compensation = 0
z_offset = -0.1
z_steps_per_mm = 0