If you want to use Simplify3d for Sindoh DP201 3D Printer, put this code into header of gcode file.

DP201header.gcode

;3DWOX Desktop Version : 1.2.689


;[Cartridge_Number] : <0>
;-----------------------------------------
;Layer_Height(mm) : 0.200000
;Wall_Thickness(mm) : 0.800000
;Enable_Retraction(0=Off,1=On) : 1
;Bottom/Top_Thickness(mm) : 0.800000
;Fill_Density(%) : 15.000000
;Nozzle_Size(mm) : 0.400000
;Print_Speed(mm/s) : 40.000000
;Temperature_Nozzle(C) : 200.000000
;Temperature_Bed(C) : 60.000000
;Support_Cartridge_Index : 0
;Support_Placement(0=None,1=Touching_buildplate,2=Everywhere) : 0
;Support_Pattern(0=Grid,1=Line,2=Zigzag) : 2
;Support_Overhang_Angle(deg) : 60.000000
;Support_Fill_Amount(%) : 20
;Support_Distance_X/Y(mm) : 0.800000
;Support_Distance_Z(mm) : 0.200000
;Support_Horizontal_Expansion(mm) : 0.800000
;Wipe_Tower(0=False,1=True) : 0
;Wipe_Tower_Size(mm) : 12.000000
;Wipe_Tower_Thickness(mm) : 4.000000
;Wipe_Tower_Fill_Density(%) : 50.000000
;Wipe_Tower_Position : 1
;Wipe_Tower_Raft_Margin(mm) : 8.000000
;Filament_Material(0=PLA,1=ABS,2=WOOD,3=PETG,4=HIPS,5=FLEXIBLE,6=PVA) : 0
;Filament_Diameter(mm) : 1.750000
;Filament_Flow_Compensation(%) : 100.000000
;Bottom_Layer_Thickness(mm) : 0.000000
;Bottom_Layer_Line_Width(%) : 120.000000
;Speed_Travel(mm/s) : 60.000000
;Speed_First_Layer(mm/s) : 10.000000
;Speed_Infill(mm/s) : 0.000000
;Speed_Top/Bottom(mm/s) : 0.000000
;Speed_Outer_Wall(mm/s) : 0.000000
;Speed_Inner_Wall(mm/s) : 0.000000
;Cool_Minimal_Layer_Time(sec) : 5.000000
;Cool_Enable_Cooling_Fan(0=Off,1=On) : 1
;Cool_Fan_Full_On_at_Height(mm) : 0.600000
;Cool_Minimum_Fan_Speed(%) : 50.000000
;Cool_Maximum_Fan_Speed(%) : 50.000000
;Cool_Minimum_Speed(mm/s) : 10.000000
;Cool_Lowering_Bed(0=Off,1=On) : 0
;Infill_Pattern(0=Automatic,1=Grid,2=Lines,3=Concentric,4=Crystal(I),5=Crystal(II)) : 0
;Infill_OVerlap(%) : 15
;Infill_Solid_Top(0=Off,1=On) : 1
;Infill_Solid_Bottom(0=Off,1=On) : 1
;Infill_Before_Wall(0=Off,1=On) : 0
;Skin_Outline(0=Off,1=On) : 0
;Skin_Type(0=Line,1=Concentric) : 0
;Bed_Adhesion_Type(0=None,1=Skirt,2=Brim,3=Raft) : 3
;Brim_Line_Amount : 10
;Skirt_Line_Count : 1
;Skirt_Gap(mm) : 3.000000
;Skirt_Minimal_Length(mm) : 150.000000
;Retraction_Speed(mm/s) : 12.000000
;Retraction_Amount : 12.000000
;Retraction_Minimal_Travle(mm) : 1.500000
;Retraction_Minimal_Extrusion(mm) : 0.000000
;Retraction_Z_Hop(mm) : 0.000000
;Retraction_Combing(0=off,1=All,2=No_Skin) : 1
;ToolChange_Retraction_Amount(mm) : 0.000000
;ToolChange_Retraction_Speed(mm/s) : 15.000000
;ToolChange_Lowering_Bed(mm) : 0.200000
;ToolChange_Extra_Restart_Amount(mm) : 0.000000
;ToolChange_Extra_Restart_Speed(mm/s) : 15.000000
;Raft_Cartridge_Index : 0
;Raft_Extra_Margin(mm) : 3.000000
;Raft_Line_Spacing(mm) : 1.000000
;Raft_Base_Thickness(mm) : 0.200000
;Raft_Base_Linewidth(mm) : 1.500000
;Raft_Interface_Thickness(mm) : 0.270000
;Raft_Interface_Linewidth(mm) : 0.400000
;Raft_Airgap(mm) : 0.000000
;Raft_First_Layer_Airgap(mm) : 0.250000
;Raft_Surface_Layers_Amount : 2.000000
;Raft_Surface_Thickness(mm) : 0.200000
;Raft_Surface_Linewidth(mm) : 0.400000
;Raft_Outline_Inset(0=Off,1=On) : 0
;Raft_Inset_Offset_Amount(mm) : 0.500000
;Raft_Temperature_Control(0=Off,1=On) : 0
;Raft_Incline(0=Off,1=On) : 0
;Error_Correction_Only_Follow_Mesh_Surface(0=Off,1=On) : 0
;Error_Correction_Combination_Mode_A(0=Off,1=On) : 1
;Error_Correction_Combination_Mode_B(0=Off,1=On) : 0
;Error_Correction_Keep_Open_Face(0=Off,1=On) : 0
;Error_Correction_Extensive_Stitching(0=Off,1=On) : 0


;FILENAME[1/1] UGl4ZWxib29rUGVuQ2Fw

;PRINTER_MODEL: [DP201]
;EMAIL_CHECKCOUNT: [0]
;ESTIMATION_TIME: [0000:08:59]

;DIMENSION: [15:17:5]
;LOCATION: [94:87]
;OPERATINGZONE: [22:25:6]

;CARTRIDGE_COUNT_TOTAL: [1]
;USEDNOZZLE: [1]
;CARTRIDGE_USED_STATE: [T]

;ESTIMATION_FILAMENT_CARTRIDGE_0: [326]
;MASS_CARTRIDGE_0: [1.0]
;MATERIAL_CARTRIDGE_0: [PLA]

;ESTIMATION_FILAMENT: [326]
;MASS: [1.0]
;MATERIAL: [PLA]

;TOTAL_MASS: [1.0]
;TOTAL_RAFTLAYER: [4]

;T0	;Raft Cartridge No: [0]

;LAYER:-3
;TYPE:RAFT

😛