alvesoaj

Semantic Commit Messages

See how a minor change to your commit message style can make you a better programmer.

Format: <type>(<scope>): <subject>

<scope> is optional

Example

alvesoaj

sudo apt-get update

sudo apt-get install -y raspberrypi-kernel-headers bc build-essential dkms git

git clone https://github.com/brektrou/rtl8821CU.git

cd rtl8821CU

nano Makefile # Then enable arm_rpi and disable others

alvesoaj

/*
 * AJ Alves ([email protected])
*/
const int MOISTURE_ANALOGIC_IN = A0; // Arduino's analogic pin
const int BOARD_RESOLUTION = 1024; // The analogic board resolution, for example Arduino Uno is 10 bit (from 0 to 1023)
const float OPERATIONAL_VOLTAGE = 5.0; // The default Arduino voltage
const float MAX_SENSOR_VOLTAGE = 3.0; // The maximum voltage that the sensor can output
const float SENSOR_READ_RATIO = OPERATIONAL_VOLTAGE / MAX_SENSOR_VOLTAGE; // The ratio betwent the two voltages

void setup() {

alvesoaj

/*
 * AJ Alves ([email protected])
*/
#define BATERRY_LEVEL_IN A0 // Arduino analogic pin
#define ANALOGIC_RESOLUTION 1024 // The analogic board resolution, for example, Arduino Uno is 10 bit (from 0 to 1023)
#define REFERENCE_VOLTAGE 5.0 // The reference voltage, for example, Arduino Uno works in 5 V reference voltage by default
#define R1 3000000.0 // resistance of R1 (3 MR)
#define R2 1000000.0 // resistance of R2 (1 MR)
#define EXPECTED_V_OUT 12 // The intented voltage, 12 V

alvesoaj

/*
 * AJ Alves ([email protected])
*/
#define SENSOR_PIN 2 // Arduino pin that will read the sensor state

void setup() {
  Serial.begin(9600); // Setup Serial Port
  pinMode(SENSOR_PIN, INPUT); // Set pin as INPUT
}

alvesoaj

/*
 * AJ Alves ([email protected])
*/
#define PUMP_PIN 2 // Water Pump Pin
 
void setup() {
  Serial.begin(9600); // Serial Port setup
  pinMode(PUMP_PIN, OUTPUT); // Set pin as OUTPUT
}
 

alvesoaj

/*
 * AJ Alves ([email protected])
*/

#define RAIN_ANALOGIC_IN A0 // Arduino's analogic pin
#define RAIN_DIGITAL_IN 4 // Arduino's digital pin
#define BOARD_RESOLUTION 1024 // The analogic board resolution, for example Arduino Uno is 10 bit (from 0 to 1023)

void setup() {
  Serial.begin(9600); // Serial Port setup

alvesoaj

int ledPin = 13; // Arduino' inner led
int sigPin = 4; // For sensor signal
int value = 0; // Holds the returned value
 
void setup(){
  Serial.begin(9600);
  pinMode(ledPin, OUTPUT); // Arduino's led as output
  pinMode(sigPin, INPUT); // signal pin as input
}
 

alvesoaj

/*
 * AJ Alves ([email protected])
*/
int ANALOG_PIN = A0; // The NodeMCU Analogic Pin
int BOARD_RESOLUTION = 1024 ; // The analogic board resolution, for example NodeMCU ESP8266 is 10 bit (from 0 to 1023)
int val = 0; // A varaible to hold the value

void setup() {
  Serial.begin(9600); // Serial Port setup
}

alvesoaj

/*
 * AJ Alves ([email protected])
*/
int ANALOG_PIN = A0; // The Arduino Analogic Pin
int BOARD_RESOLUTION = 1024 ; // The analogic board resolution, for example Arduino Uno is 10 bit (from 0 to 1023)
int val = 0; // A varaible to hold the value

void setup() {
  Serial.begin(9600); // Serial Port setup
}