Last active
May 1, 2018 08:33
-
-
Save anddam/3637fc4f948a073a5a628a61bdf519c3 to your computer and use it in GitHub Desktop.
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| $ iw wlp1s0 info | |
| Interface wlp1s0 | |
| ifindex 3 | |
| wdev 0x1 | |
| addr a0:d3:7a:37:20:5d | |
| type managed | |
| wiphy 0 | |
| channel 1 (2412 MHz), width: 20 MHz, center1: 2412 MHz | |
| $ uname -rms | |
| Linux 4.13.0-39-generic x86_64 | |
| $ iw phy | |
| Wiphy phy0 | |
| max # scan SSIDs: 20 | |
| max scan IEs length: 425 bytes | |
| Retry short limit: 7 | |
| Retry long limit: 4 | |
| Coverage class: 0 (up to 0m) | |
| Device supports RSN-IBSS. | |
| Device supports AP-side u-APSD. | |
| Supported Ciphers: | |
| * WEP40 (00-0f-ac:1) | |
| * WEP104 (00-0f-ac:5) | |
| * TKIP (00-0f-ac:2) | |
| * CCMP (00-0f-ac:4) | |
| * CMAC (00-0f-ac:6) | |
| Available Antennas: TX 0 RX 0 | |
| Supported interface modes: | |
| * IBSS | |
| * managed | |
| * AP | |
| * AP/VLAN | |
| * monitor | |
| * P2P-client | |
| * P2P-GO | |
| * P2P-device | |
| Band 1: | |
| Capabilities: 0x116e | |
| HT20/HT40 | |
| SM Power Save disabled | |
| RX HT20 SGI | |
| RX HT40 SGI | |
| RX STBC 1-stream | |
| Max AMSDU length: 3839 bytes | |
| DSSS/CCK HT40 | |
| Maximum RX AMPDU length 65535 bytes (exponent: 0x003) | |
| Minimum RX AMPDU time spacing: 4 usec (0x05) | |
| HT TX/RX MCS rate indexes supported: 0-7 | |
| Bitrates (non-HT): | |
| * 1.0 Mbps | |
| * 2.0 Mbps (short preamble supported) | |
| * 5.5 Mbps (short preamble supported) | |
| * 11.0 Mbps (short preamble supported) | |
| * 6.0 Mbps | |
| * 9.0 Mbps | |
| * 12.0 Mbps | |
| * 18.0 Mbps | |
| * 24.0 Mbps | |
| * 36.0 Mbps | |
| * 48.0 Mbps | |
| * 54.0 Mbps | |
| Frequencies: | |
| * 2412 MHz [1] (22.0 dBm) | |
| * 2417 MHz [2] (22.0 dBm) | |
| * 2422 MHz [3] (22.0 dBm) | |
| * 2427 MHz [4] (22.0 dBm) | |
| * 2432 MHz [5] (22.0 dBm) | |
| * 2437 MHz [6] (22.0 dBm) | |
| * 2442 MHz [7] (22.0 dBm) | |
| * 2447 MHz [8] (22.0 dBm) | |
| * 2452 MHz [9] (22.0 dBm) | |
| * 2457 MHz [10] (22.0 dBm) | |
| * 2462 MHz [11] (22.0 dBm) | |
| * 2467 MHz [12] (22.0 dBm) (no IR) | |
| * 2472 MHz [13] (22.0 dBm) (no IR) | |
| Band 2: | |
| Capabilities: 0x116e | |
| HT20/HT40 | |
| SM Power Save disabled | |
| RX HT20 SGI | |
| RX HT40 SGI | |
| RX STBC 1-stream | |
| Max AMSDU length: 3839 bytes | |
| DSSS/CCK HT40 | |
| Maximum RX AMPDU length 65535 bytes (exponent: 0x003) | |
| Minimum RX AMPDU time spacing: 4 usec (0x05) | |
| HT TX/RX MCS rate indexes supported: 0-7 | |
| VHT Capabilities (0x33807120): | |
| Max MPDU length: 3895 | |
| Supported Channel Width: neither 160 nor 80+80 | |
| short GI (80 MHz) | |
| SU Beamformee | |
| RX antenna pattern consistency | |
| TX antenna pattern consistency | |
| VHT RX MCS set: | |
| 1 streams: MCS 0-9 | |
| 2 streams: not supported | |
| 3 streams: not supported | |
| 4 streams: not supported | |
| 5 streams: not supported | |
| 6 streams: not supported | |
| 7 streams: not supported | |
| 8 streams: not supported | |
| VHT RX highest supported: 0 Mbps | |
| VHT TX MCS set: | |
| 1 streams: MCS 0-9 | |
| 2 streams: not supported | |
| 3 streams: not supported | |
| 4 streams: not supported | |
| 5 streams: not supported | |
| 6 streams: not supported | |
| 7 streams: not supported | |
| 8 streams: not supported | |
| VHT TX highest supported: 0 Mbps | |
| Bitrates (non-HT): | |
| * 6.0 Mbps | |
| * 9.0 Mbps | |
| * 12.0 Mbps | |
| * 18.0 Mbps | |
| * 24.0 Mbps | |
| * 36.0 Mbps | |
| * 48.0 Mbps | |
| * 54.0 Mbps | |
| Frequencies: | |
| * 5180 MHz [36] (22.0 dBm) (no IR) | |
| * 5200 MHz [40] (22.0 dBm) (no IR) | |
| * 5220 MHz [44] (22.0 dBm) (no IR) | |
| * 5240 MHz [48] (22.0 dBm) (no IR) | |
| * 5260 MHz [52] (22.0 dBm) (no IR, radar detection) | |
| DFS state: usable (for 42344 sec) | |
| DFS CAC time: 0 ms | |
| * 5280 MHz [56] (22.0 dBm) (no IR, radar detection) | |
| DFS state: usable (for 42344 sec) | |
| DFS CAC time: 0 ms | |
| * 5300 MHz [60] (22.0 dBm) (no IR, radar detection) | |
| DFS state: usable (for 42344 sec) | |
| DFS CAC time: 0 ms | |
| * 5320 MHz [64] (22.0 dBm) (no IR, radar detection) | |
| DFS state: usable (for 42344 sec) | |
| DFS CAC time: 0 ms | |
| * 5500 MHz [100] (22.0 dBm) (no IR, radar detection) | |
| DFS state: usable (for 42344 sec) | |
| DFS CAC time: 0 ms | |
| * 5520 MHz [104] (22.0 dBm) (no IR, radar detection) | |
| DFS state: usable (for 42344 sec) | |
| DFS CAC time: 0 ms | |
| * 5540 MHz [108] (22.0 dBm) (no IR, radar detection) | |
| DFS state: usable (for 42344 sec) | |
| DFS CAC time: 0 ms | |
| * 5560 MHz [112] (22.0 dBm) (no IR, radar detection) | |
| DFS state: usable (for 42344 sec) | |
| DFS CAC time: 0 ms | |
| * 5580 MHz [116] (22.0 dBm) (no IR, radar detection) | |
| DFS state: usable (for 42344 sec) | |
| DFS CAC time: 0 ms | |
| * 5600 MHz [120] (22.0 dBm) (no IR, radar detection) | |
| DFS state: usable (for 42344 sec) | |
| DFS CAC time: 0 ms | |
| * 5620 MHz [124] (22.0 dBm) (no IR, radar detection) | |
| DFS state: usable (for 42344 sec) | |
| DFS CAC time: 0 ms | |
| * 5640 MHz [128] (22.0 dBm) (no IR, radar detection) | |
| DFS state: usable (for 42344 sec) | |
| DFS CAC time: 0 ms | |
| * 5660 MHz [132] (22.0 dBm) (no IR, radar detection) | |
| DFS state: usable (for 42344 sec) | |
| DFS CAC time: 0 ms | |
| * 5680 MHz [136] (22.0 dBm) (no IR, radar detection) | |
| DFS state: usable (for 42344 sec) | |
| DFS CAC time: 0 ms | |
| * 5700 MHz [140] (22.0 dBm) (no IR, radar detection) | |
| DFS state: usable (for 42344 sec) | |
| DFS CAC time: 0 ms | |
| * 5720 MHz [144] (22.0 dBm) (no IR, radar detection) | |
| DFS state: usable (for 42344 sec) | |
| DFS CAC time: 0 ms | |
| * 5745 MHz [149] (22.0 dBm) (no IR) | |
| * 5765 MHz [153] (22.0 dBm) (no IR) | |
| * 5785 MHz [157] (22.0 dBm) (no IR) | |
| * 5805 MHz [161] (22.0 dBm) (no IR) | |
| * 5825 MHz [165] (22.0 dBm) (no IR) | |
| Supported commands: | |
| * new_interface | |
| * set_interface | |
| * new_key | |
| * start_ap | |
| * new_station | |
| * new_mpath | |
| * set_mesh_config | |
| * set_bss | |
| * authenticate | |
| * associate | |
| * deauthenticate | |
| * disassociate | |
| * join_ibss | |
| * join_mesh | |
| * remain_on_channel | |
| * set_tx_bitrate_mask | |
| * frame | |
| * frame_wait_cancel | |
| * set_wiphy_netns | |
| * set_channel | |
| * set_wds_peer | |
| * start_sched_scan | |
| * probe_client | |
| * set_noack_map | |
| * register_beacons | |
| * start_p2p_device | |
| * set_mcast_rate | |
| * connect | |
| * disconnect | |
| * channel_switch | |
| * Unknown command (104) | |
| * Unknown command (105) | |
| * Unknown command (121) | |
| Supported TX frame types: | |
| * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| Supported RX frame types: | |
| * IBSS: 0x40 0xb0 0xc0 0xd0 | |
| * managed: 0x40 0xd0 | |
| * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 | |
| * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 | |
| * mesh point: 0xb0 0xc0 0xd0 | |
| * P2P-client: 0x40 0xd0 | |
| * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 | |
| * P2P-device: 0x40 0xd0 | |
| WoWLAN support: | |
| * wake up on disconnect | |
| * wake up on magic packet | |
| * wake up on pattern match, up to 20 patterns of 16-128 bytes, | |
| maximum packet offset 0 bytes | |
| * can do GTK rekeying | |
| * wake up on GTK rekey failure | |
| * wake up on EAP identity request | |
| * wake up on 4-way handshake | |
| * wake up on rfkill release | |
| * wake up on TCP connection | |
| software interface modes (can always be added): | |
| * AP/VLAN | |
| * monitor | |
| valid interface combinations: | |
| * #{ managed } <= 1, #{ AP, P2P-client, P2P-GO } <= 1, #{ P2P-device } <= 1, | |
| total <= 3, #channels <= 2 | |
| HT Capability overrides: | |
| * MCS: ff ff ff ff ff ff ff ff ff ff | |
| * maximum A-MSDU length | |
| * supported channel width | |
| * short GI for 40 MHz | |
| * max A-MPDU length exponent | |
| * min MPDU start spacing | |
| Device supports TX status socket option. | |
| Device supports HT-IBSS. | |
| Device supports SAE with AUTHENTICATE command | |
| Device supports low priority scan. | |
| Device supports scan flush. | |
| Device supports per-vif TX power setting | |
| P2P GO supports CT window setting | |
| P2P GO supports opportunistic powersave setting | |
| Driver supports full state transitions for AP/GO clients | |
| Driver supports a userspace MPM | |
| Driver/device bandwidth changes during BSS lifetime (AP/GO mode) | |
| Device supports static SMPS | |
| Device supports dynamic SMPS |
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| $ /System/Library/PrivateFrameworks/Apple80211.framework/Versions/Current/Resources/airport --getinfo | |
| agrCtlRSSI: -61 | |
| agrExtRSSI: 0 | |
| agrCtlNoise: -86 | |
| agrExtNoise: 0 | |
| state: running | |
| op mode: station | |
| lastTxRate: 130 | |
| maxRate: 144 | |
| lastAssocStatus: 0 | |
| 802.11 auth: open | |
| link auth: wpa2-psk | |
| BSSID: 10:13:31:53:9e:7f | |
| SSID: brapinet wifi | |
| MCS: 15 | |
| channel: 1 | |
| $ uname -rms | |
| Darwin 17.5.0 x86_64 |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment