Gigabyte Aorus - Linux fan control.md

PWM fan control in Linux with a Gigabyte Aorus motherboard

• install lm-sensors with your package manager

sensors

If it won't show any fan/speed, continue

sensor-detect

Say YES to at least "Super I/O sensors"

Expected output:

Trying family `ITE'...                                      Yes
Found unknown chip with ID 0x8688

If similar, continue

git clone https://github.com/frankcrawford/it87

cd it87
sudo make clean
sudo make install
sudo modprobe it87 ignore_resource_conflict=1 force_id=0x8622

sensors

The fans should show up now, if yes, continue to make them available at boot:

echo options it87 ignore_resource_conflict=1 force_id=0x8622 > /etc/modprobe.d/it87.conf
echo it87 >> /etc/modules

after i execute "sudo modprobe it87 ignore_resource_conflict=1 force_id=0x8622" i get the error "modprobe: ERROR: could not insert 'it87': No such device". Do you know how to fix the issue?

thx a lot for this. I've made a fork added 2 missing commands.

Thanks for this! ☺️

Why was ignore_resource_conflict=1 added? It works fine here on a Gigabyte Auros motherboard without.

For a GA-Z170N-WIFI (rev. 1.0), just modprobe it87 is enough, you can just load the it87 module without any of the options outlined above. This enables not only fan speed sensors but also voltages and various other temperature sensors

echo it87 > /etc/modules-load.d/gigabyte-sensors-it87.conf

Full sensor output:

~ sensors
iwlwifi_1-virtual-0
Adapter: Virtual device
temp1:        +33.0°C  

it8628-isa-0a40
Adapter: ISA adapter
in0:         300.00 mV (min =  +0.00 V, max =  +3.06 V)
in1:           2.03 V  (min =  +0.00 V, max =  +3.06 V)
in2:           2.02 V  (min =  +0.00 V, max =  +3.06 V)
in3:           2.02 V  (min =  +0.00 V, max =  +3.06 V)
in4:          12.00 mV (min =  +0.00 V, max =  +3.06 V)
in5:           1.07 V  (min =  +0.00 V, max =  +3.06 V)
in6:           1.36 V  (min =  +0.00 V, max =  +3.06 V)
3VSB:          3.38 V  (min =  +0.00 V, max =  +6.12 V)
Vbat:          3.14 V  
fan1:        1520 RPM  (min =    0 RPM)
fan2:        20454 RPM  (min =    0 RPM)
fan3:           0 RPM  (min =    0 RPM)
fan4:           0 RPM  (min =    0 RPM)
fan5:           0 RPM  (min =    0 RPM)
temp1:        +37.0°C  (low  = +127.0°C, high = +127.0°C)  sensor = thermistor
temp2:        +44.0°C  (low  = +127.0°C, high = +127.0°C)  sensor = thermistor
temp3:        +42.0°C  (low  = +127.0°C, high = +127.0°C)  sensor = Intel PECI
temp4:        +45.0°C  
temp5:        +37.0°C  
temp6:        +32.0°C  
intrusion0:  ALARM

acpitz-acpi-0
Adapter: ACPI interface
temp1:        +27.8°C  (crit = +119.0°C)
temp2:        +29.8°C  (crit = +119.0°C)

coretemp-isa-0000
Adapter: ISA adapter
Package id 0:  +43.0°C  (high = +74.0°C, crit = +80.0°C)
Core 0:        +43.0°C  (high = +74.0°C, crit = +80.0°C)
Core 1:        +41.0°C  (high = +74.0°C, crit = +80.0°C)
Core 2:        +42.0°C  (high = +74.0°C, crit = +80.0°C)
Core 3:        +41.0°C  (high = +74.0°C, crit = +80.0°C)

nvme-pci-0b00
Adapter: PCI adapter
Composite:    +41.9°C  (low  =  -5.2°C, high = +79.8°C)
                       (crit = +84.8°C)

fan1 is CPU and fan2 is SYSTEM. Looks like the system incorrectly reports a high RPM number when the fan is receiving some voltage but not enough to spin it up

When I ran sudo make make install I got the output make: *** No rule to make target 'make'. Stop. and the fans still don't show up. Any ideas?

@aiintdeadyet that's a typo. it should read sudo make install (or maybe sudo make && sudo make install)

It's now git clone https://github.com/frankcrawford/it87, https://github.com/a1wong/it87.git doesn't seem to get any more updates

Hopefully helpful additional information:

1. I can't speak for all chips, but anecdotally (and in the README for the module) the options ignore_resource_conflict=1 and force_id=0x8622 (or whatever the chip's ID is) should only be used for testing and troubleshooting. The module should do a good job at detecting what is needed automatically - on top of that, if you ever restore a backup of your system to different hardware, the ignore_resource_conflict option could cause boot issues.
2. For any Arch users, Kernel modules are not loaded by /etc/modules but instead by .conf files in /etc/modules-load.d - see https://wiki.archlinux.org/title/Kernel_module for more information, under "Automatic module loading"

Aorus B450 on Ubuntu 24.04 & sensors 3.6.0.
The it87 is detected with no tweak required but sensors shows only 3 fans with 0 RPM:

it8792-isa-0a60
Adapter: ISA adapter
in0:           1.79 V  (min =  +0.00 V, max =  +2.78 V)
in1:           1.29 V  (min =  +0.00 V, max =  +2.78 V)
in2:           1.17 V  (min =  +0.00 V, max =  +2.78 V)
+3.3V:         3.36 V  (min =  +0.00 V, max =  +5.56 V)
in4:           1.26 V  (min =  +0.00 V, max =  +2.78 V)
in5:           1.13 V  (min =  +0.00 V, max =  +2.78 V)
in6:           2.78 V  (min =  +0.00 V, max =  +2.78 V)  ALARM
3VSB:          3.33 V  (min =  +0.00 V, max =  +5.56 V)
Vbat:          3.10 V  
fan1:           0 RPM  (min =    0 RPM)
fan2:           0 RPM  (min =    0 RPM)
fan3:           0 RPM  (min =    0 RPM)
temp1:        +30.0°C  (low  = +127.0°C, high = +127.0°C)  sensor = thermistor
temp2:        +36.0°C  (low  = +127.0°C, high = +127.0°C)  sensor = thermistor
temp3:        +36.0°C  (low  = +127.0°C, high = +127.0°C)  sensor = thermistor
intrusion0:  ALARM

k10temp-pci-00c3
Adapter: PCI adapter
Tctl:         +27.5°C  

acpitz-acpi-0
Adapter: ACPI interface
temp1:        +16.8°C  

amdgpu-pci-0c00
Adapter: PCI adapter
vddgfx:           N/A  
vddnb:            N/A  
edge:         +27.0°C  

nvme-pci-0b00
Adapter: PCI adapter
Composite:    +36.9°C  (low  =  -0.1°C, high = +84.8°C)
                       (crit = +94.8°C)
Sensor 1:     +36.9°C  (low  = -273.1°C, high = +65261.8°C)
Sensor 2:     +42.9°C  (low  = -273.1°C, high = +65261.8°C)
Sensor 8:     +36.9°C  (low  = -273.1°C, high = +65261.8°C)

Not sure someone else has this issue.

I also have 2 PCI cards (HBA & SFP+) with builtin sensors which don't show but that's another story.

Aorus B450 on Ubuntu 24.04 & sensors 3.6.0. The it87 is detected with no tweak required but sensors shows only 3 fans with 0 RPM:

it8792-isa-0a60
Adapter: ISA adapter
in0:           1.79 V  (min =  +0.00 V, max =  +2.78 V)
in1:           1.29 V  (min =  +0.00 V, max =  +2.78 V)
in2:           1.17 V  (min =  +0.00 V, max =  +2.78 V)
+3.3V:         3.36 V  (min =  +0.00 V, max =  +5.56 V)
in4:           1.26 V  (min =  +0.00 V, max =  +2.78 V)
in5:           1.13 V  (min =  +0.00 V, max =  +2.78 V)
in6:           2.78 V  (min =  +0.00 V, max =  +2.78 V)  ALARM
3VSB:          3.33 V  (min =  +0.00 V, max =  +5.56 V)
Vbat:          3.10 V  
fan1:           0 RPM  (min =    0 RPM)
fan2:           0 RPM  (min =    0 RPM)
fan3:           0 RPM  (min =    0 RPM)
temp1:        +30.0°C  (low  = +127.0°C, high = +127.0°C)  sensor = thermistor
temp2:        +36.0°C  (low  = +127.0°C, high = +127.0°C)  sensor = thermistor
temp3:        +36.0°C  (low  = +127.0°C, high = +127.0°C)  sensor = thermistor
intrusion0:  ALARM

k10temp-pci-00c3
Adapter: PCI adapter
Tctl:         +27.5°C  

acpitz-acpi-0
Adapter: ACPI interface
temp1:        +16.8°C  

amdgpu-pci-0c00
Adapter: PCI adapter
vddgfx:           N/A  
vddnb:            N/A  
edge:         +27.0°C  

nvme-pci-0b00
Adapter: PCI adapter
Composite:    +36.9°C  (low  =  -0.1°C, high = +84.8°C)
                       (crit = +94.8°C)
Sensor 1:     +36.9°C  (low  = -273.1°C, high = +65261.8°C)
Sensor 2:     +42.9°C  (low  = -273.1°C, high = +65261.8°C)
Sensor 8:     +36.9°C  (low  = -273.1°C, high = +65261.8°C)

Not sure someone else has this issue.

I also have 2 PCI cards (HBA & SFP+) with builtin sensors which don't show but that's another story.

I have this same issue, were you able to resolve it?

No still no luck for now

I have the same issue, 3 fans with 0RPM, on Aorus Master Z490

I want to test this solution but, if something doesn't work for me, how I can uninstall this? (I'm using Manjaro in an Gigabyte b760m Aorus MB).

1. The command to build is wrong. It should be

make clean
make
sudo make install

(the make command in particular is missing)

2. If sensors-detect only throw errors like /dev/port: Operation not permitted, it means you have Secure Boot activated. You need to deactivate it in the BIOS
3. Make sure you compile and in particular install it87 in the current version of the kernel (I waited to reboot, updated the system, and it87 wasn't found by modprobe No such device. A tip, just in case…
4. If modprobe throw Device or resource busy, check dmesg. If you have ACPI: OSL: Resource conflict; ACPI support missing from driver?, then you need either the ignore_resource_conflict=1 part, or you need to add acpi_enforce_resources=lax to the kernel options. I choose the first choice, because it doesn't change the whole system.

So in the end, I used sudo modprobe it87 ignore_resource_conflict=1, and it worked.

As for only one fan showing RPMs, I believe, at least in my case, that I only have one fan plugged to the motherboard PWM plugs, the others being controlled by the PC's case itself.

@danielsanfr Using modprobe means you are using a module right now only. It won't stay after a reboot. But even there, you can use the option -r with modprobe to remove a module.

From trying out these instructions on Z390 AORUS ULTRA, I found that only one of these steps is sufficient.

• Get a recent Linux kernel and make sure to actually set force_id=0x8622, it is necessary. Otherwise you'll be getting all fans showing 0 RPM.

  With this, I think we are telling the sub-par built-in driver a wrong device ID so that it can display something via support for some other device.

OR:

• Install this custom kernel module frankcrawford/it87 aka it87-dkms-git. Then reboot, otherwise it's not actually kicking in.

  With it, no settings are necessary and it seems to detect and apply the correct device.