Skip to content

Instantly share code, notes, and snippets.

Show Gist options
  • Save bakueikozo/048eddad7a08416d4f59580a48465124 to your computer and use it in GitHub Desktop.
Save bakueikozo/048eddad7a08416d4f59580a48465124 to your computer and use it in GitHub Desktop.
OK
U-Boot 2010.03.v1.24-20120919 (2012/09/19 - 18:48:37) for TJMedia TDMK Android
APLL:1000MHz, MPLL:800MHz, VPLL:212MHz
I2C: ready
PMIC: max8997 v0.4 0-0-0 1250mV-1100mV-1200mV
DRAM: 1 GB
MMC: 0:7576 MB, 1:0 MB, 2:0 MB
Board: TDMK Rev.6
S/N: AK056772
*** Warning - using default environment
In: serial
Out: serial
Err: serial
Checking Boot Mode ...7(29h) : EMMC4.41
Hit any key to stop autoboot: 1  0
reading kernel.. 1120, 8192 0, 0x40008000, 0x460, 0x2000
MMC read: dev # 0, block # 1120, count 8192 ...8192 blocks read: OK
completed
reading RFS.. 9312, 2048 0, 0x42000000, 0x2460, 0x800
MMC read: dev # 0, block # 9312, count 2048 ...2048 blocks read: OK
completed
Boot with zImage
## Loading init Ramdisk from Legacy Image at 42000000 ...
Image Name: ramdisk
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 308276 Bytes = 301.1 kB
Load Address: 40800000
Entry Point: 40800000
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.35.8-v2.03-20190111 (TDMK@TDMK-DEV) (gcc version 4.4.3 (GCC) ) #244 SMP PREEMPT Fri Jan 11 09:06:33 KST 2019
[ 0.000000] CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: TDMK
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] TDMK bootloader version : v1.24-20120919
[ 0.000000] TDMK serial number : AK056772
[ 0.000000] TDMK revision : 6
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] CPU S5PV310 (id 0x43210011)
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] s3c_register_clksrc: clock armclk has no registers set
[ 0.000000] mout_audss: bad source 0
[ 0.000000] s5pv310_register_clocks FSYS_BLK_SORC_CLK[0x66666][0x500000][0x80007]
[ 0.000000] S5PV310: ARMCLK=1000000000, DMC=400000000, ACLK200=200000000
[ 0.000000] ACLK100=100000000, ACLK160=160000000, ACLK133=133333333
[ 0.000000] uclk1: source is mout_mpll (6), rate is 100000000
[ 0.000000] uclk1: source is mout_mpll (6), rate is 100000000
[ 0.000000] uclk1: source is mout_mpll (6), rate is 100000000
[ 0.000000] uclk1: source is mout_mpll (6), rate is 100000000
[ 0.000000] uclk1: source is mout_mpll (6), rate is 100000000
[ 0.000000] sclk_pwm: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_csis: source is xusbxti (1), rate is 24000000
[ 0.000000] sclk_csis: source is xusbxti (1), rate is 24000000
[ 0.000000] sclk_cam0: source is xusbxti (1), rate is 24000000
[ 0.000000] sclk_cam1: source is xusbxti (1), rate is 24000000
[ 0.000000] sclk_fimc: source is xusbxti (1), rate is 24000000
[ 0.000000] sclk_fimc: source is xusbxti (1), rate is 24000000
[ 0.000000] sclk_fimc: source is xusbxti (1), rate is 24000000
[ 0.000000] sclk_fimc: source is xusbxti (1), rate is 24000000
[ 0.000000] sclk_mixer: source is sclk_dac (0), rate is 24000000
[ 0.000000] sclk_fimd: source is xusbxti (1), rate is 24000000
[ 0.000000] sclk_fimd: source is xusbxti (1), rate is 24000000
[ 0.000000] sclk_sata: source is mout_mpll (0), rate is 133333333
[ 0.000000] sclk_spi: source is xusbxti (1), rate is 24000000
[ 0.000000] sclk_spi: source is mout_mpll (6), rate is 80000000
[ 0.000000] sclk_spi: source is xusbxti (1), rate is 24000000
[ 0.000000] sclk_fimg2d: source is mout_g2d0 (0), rate is 100000000
[ 0.000000] sclk_mfc: source is mout_mfc0 (0), rate is 200000000
[ 0.000000] sclk_g3d: source is mout_g3d0 (0), rate is 166666666
[ 0.000000] sclk_pwi: source is xusbxti (1), rate is 12000000
[ 0.000000] mem infor: bank0 start-> 0x40000000, bank0 size-> 0x20000000
[ 0.000000] bank1 start-> 0x60000000, bank1 size-> 0x7f00000
[ 0.000000] CMA reserve : fimg2d, addr is 0x5f800000, size is 0x800000
[ 0.000000] CMA reserve : jpeg, addr is 0x5f580000, size is 0x280000
[ 0.000000] CMA reserve : fimc3, addr is 0x5f280000, size is 0x300000
[ 0.000000] CMA reserve : fimc2, addr is 0x5da80000, size is 0x1800000
[ 0.000000] CMA reserve : fimc1, addr is 0x5ce80000, size is 0xc00000
[ 0.000000] CMA reserve : fimc0, addr is 0x5c6b0000, size is 0x7d0000
[ 0.000000] CMA reserve : mfc1, addr is 0x5a2b0000, size is 0x2400000
[ 0.000000] CMA reserve : mfc0, addr is 0x57eb0000, size is 0x2400000
[ 0.000000] CMA reserve : fimd, addr is 0x576e0000, size is 0x7d0000
[ 0.000000] CMA reserve : pmem_gpu1, addr is 0x56ce0000, size is 0xa00000
[ 0.000000] CMA reserve : pmem, addr is 0x52ce0000, size is 0x4000000
[ 0.000000] PERCPU: Embedded 7 pages/cpu @e0015000 s5792 r8192 d14688 u65536
[ 0.000000] pcpu-alloc: s5792 r8192 d14688 u65536 alloc=16*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259080
[ 0.000000] Kernel command line: androidboot.bootloader=v1.24-20120919 androidboot.serialno=AK056772 androidboot.rev=6 console=ttySAC0,115200 androidboot.console=s3c2410_serial0 vmalloc=129MB
[ 0.000000] TDMK bootloader version : v1.24-20120919
[ 0.000000] TDMK serial number : AK056772
[ 0.000000] TDMK revision : 6
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 512MB 127MB 381MB = 1020MB total
[ 0.000000] Memory: 811412k/811412k available, 233068k reserved, 390144K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xff600000 - 0xffe00000 ( 8 MB)
[ 0.000000] vmalloc : 0xe8000000 - 0xf0000000 ( 128 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe7f00000 ( 639 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0031000 ( 164 kB)
[ 0.000000] .text : 0xc0031000 - 0xc05aa000 (5604 kB)
[ 0.000000] .data : 0xc05c8000 - 0xc0680180 ( 737 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:596
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttySAC0] enabled
[ 0.496974] Calibrating delay loop... 1992.29 BogoMIPS (lpj=4980736)
[ 0.630056] pid_max: default: 32768 minimum: 301
[ 0.630199] Mount-cache hash table entries: 512
[ 0.630663] Initializing cgroup subsys debug
[ 0.630721] Initializing cgroup subsys cpuacct
[ 0.630788] Initializing cgroup subsys freezer
[ 0.632744] CPU: Testing write buffer coherency: ok
[ 0.637774] L310 cache controller enabled
[ 0.641617] l2x0: 16 ways, CACHE_ID 0x4100c4c5, AUX_CTRL 0x7e470001, Cache Size: 1048576 B
[ 0.650026] >made stopper
[ 0.660023] >made stopper
[ 0.670100] CPU1: Booted secondary processor
[ 0.670161] Brought up 2 CPUs
[ 0.670239] SMP: Total of 2 processors activated (3984.58 BogoMIPS).
[ 0.675191] regulator: core version 0.5
[ 0.675318] NET: Registered protocol family 16
[ 0.678525] S3C Power Management, Copyright 2004 Simtec Electronics
[ 0.683100] s3c_rtc_base: e8008000
[ 0.686468] tdmk_cam_power: set camera power off
[ 0.797381] S5PV310: Initializing architecture
[ 0.797758] s5pv310-adc s3c64xx-adc: attached adc driver
[ 0.797872] samsung-pd samsung-pd.0: power domain registered
[ 0.797939] Disable:samsung-pd.0 ++
[ 0.797981] samsung-pd samsung-pd.0: samsung-pd.0 is not enabled
[ 0.799921] samsung-pd samsung-pd.1: power domain registered
[ 0.805565] Disable:samsung-pd.1 ++
[ 0.809022] samsung-pd samsung-pd.1: samsung-pd.1 is not enabled
[ 0.815035] samsung-pd samsung-pd.2: power domain registered
[ 0.820665] Disable:samsung-pd.2 ++
[ 0.824125] samsung-pd samsung-pd.2: samsung-pd.2 is not enabled
[ 0.830138] samsung-pd samsung-pd.3: power domain registered
[ 0.835768] Disable:samsung-pd.3 ++
[ 0.839229] samsung-pd samsung-pd.3: samsung-pd.3 is not enabled
[ 0.845241] samsung-pd samsung-pd.5: power domain registered
[ 0.850872] Disable:samsung-pd.5 ++
[ 0.854332] samsung-pd samsung-pd.5: samsung-pd.5 is not enabled
[ 0.860341] samsung-pd samsung-pd.6: power domain registered
[ 0.865974] Disable:samsung-pd.6 ++
[ 0.869435] samsung-pd samsung-pd.6: samsung-pd.6 is not enabled
[ 0.875447] samsung-pd samsung-pd.4: power domain registered
[ 0.881078] Disable:samsung-pd.4 ++
[ 0.884538] samsung-pd samsung-pd.4: samsung-pd.4 is not enabled
[ 0.890619] s3c24xx-pwm s3c24xx-pwm.0: tin at 100000000, tdiv at 100000000, tin=divclk, base 0
[ 0.899152] s3c24xx-pwm s3c24xx-pwm.1: tin at 100000000, tdiv at 100000000, tin=divclk, base 8
[ 0.907741] s3c24xx-pwm s3c24xx-pwm.2: tin at 100000000, tdiv at 100000000, tin=divclk, base 12
[ 0.916420] s3c24xx-pwm s3c24xx-pwm.3: tin at 100000000, tdiv at 100000000, tin=divclk, base 16
[ 0.925179] UMP: UMP device driver loaded
[ 0.933340] bio: create slab <bio-0> at 0
[ 0.933927] SCSI subsystem initialized
[ 0.936974] usbcore: registered new interface driver usbfs
[ 0.942419] usbcore: registered new interface driver hub
[ 0.947731] usbcore: registered new device driver usb
[ 0.952839] INFO I2C WAIT TIme List (msec)
[ 0.956777] s3c-i2c s3c2440-i2c.0: Always Enable I2C Clock
[ 0.962334] s3c-i2c s3c2440-i2c.0: slave address 0x10
[ 0.967359] s3c-i2c s3c2440-i2c.0: bus frequency set to 97 KHz
[ 0.973180] i2c ch[0], ack wait max time 15000(msec)
[ 1.017222] regulator: VDD_33_ABB: 3300 mV
[ 1.019212] regulator: VDD_11ON: 1100 mV
[ 1.021189] regulator: VDD_11OFF: 1100 mV
[ 1.023168] regulator: VDD_18ON: 1800 mV
[ 1.025148] regulator: VDD_18OFF: 1800 mV
[ 1.027135] set_machine_constraints: ~~~~~~~~~~~~~~~~~~~~~~~~~ disable VDD_18AUD
[ 1.029148] regulator: VDD_33OFF: 3300 mV
[ 1.031131] regulator: VDD_33ON: 3300 mV
[ 1.033111] regulator: VDD_11ON_PLL: 1100 mV
[ 1.036977] set_machine_constraints: ~~~~~~~~~~~~~~~~~~~~~~~~~ disable VDD_AUD
[ 1.044165] set_machine_constraints: ~~~~~~~~~~~~~~~~~~~~~~~~~ disable VDD_LDO12
[ 1.051544] set_machine_constraints: ~~~~~~~~~~~~~~~~~~~~~~~~~ disable VDD_LDO13
[ 1.058921] set_machine_constraints: ~~~~~~~~~~~~~~~~~~~~~~~~~ disable AVDD18_SWB
[ 1.066400] regulator: VDD_33ON_LAN: 3300 mV
[ 1.070744] set_machine_constraints: ~~~~~~~~~~~~~~~~~~~~~~~~~ disable VDD_33OFF_EXT1
[ 1.078541] regulator: VDD33_SWB: 3300 mV
[ 1.082628] set_machine_constraints: ~~~~~~~~~~~~~~~~~~~~~~~~~ disable VDD_33OFF_EXT2
[ 1.090444] regulator: VDD_MIF: 1100 mV
[ 1.094338] regulator: VDD_ARM: 1200 mV
[ 1.098257] regulator: VDD_INT: 1100 mV
[ 1.101444] regulator: VDD_G3D: 900 <--> 1200 mV at 1200 mV
[ 1.106671] set_machine_constraints: ~~~~~~~~~~~~~~~~~~~~~~~~~ disable VDD_12OFF_EXT1
[ 1.115610] regulator: VDD_M15OFF: 1500 mV
[ 1.119770] regulator: VDD_33OFF_EXT3: 3500 mV
[ 1.122677] ====================> max8997_pmic_probe <=======================
[ 1.129805] ==> WIFI PDN HIGH
[ 1.431797] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[ 1.431866] INFO I2C WAIT TIme List (msec)
[ 1.431920] s3c-i2c s3c2440-i2c.1: Always Enable I2C Clock
[ 1.431991] s3c-i2c s3c2440-i2c.1: slave address 0x10
[ 1.432049] s3c-i2c s3c2440-i2c.1: bus frequency set to 97 KHz
[ 1.435385] i2c ch[1], ack wait max time 15000(msec)
[ 1.440537] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[ 1.445713] INFO I2C WAIT TIme List (msec)
[ 1.449775] s3c-i2c s3c2440-i2c.2: Always Enable I2C Clock
[ 1.455345] s3c-i2c s3c2440-i2c.2: slave address 0x10
[ 1.460374] s3c-i2c s3c2440-i2c.2: bus frequency set to 19 KHz
[ 1.466195] i2c ch[2], ack wait max time 40000(msec)
[ 1.471195] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
[ 1.476526] INFO I2C WAIT TIme List (msec)
[ 1.480603] s3c-i2c s3c2440-i2c.3: Always Enable I2C Clock
[ 1.486158] s3c-i2c s3c2440-i2c.3: slave address 0x10
[ 1.491187] s3c-i2c s3c2440-i2c.3: bus frequency set to 97 KHz
[ 1.497009] i2c ch[3], ack wait max time 150000(msec)
[ 1.502096] s3c-i2c s3c2440-i2c.3: i2c-3: S3C I2C adapter
[ 1.507428] INFO I2C WAIT TIme List (msec)
[ 1.511501] s3c-i2c s3c2440-i2c.4: Always Enable I2C Clock
[ 1.517059] s3c-i2c s3c2440-i2c.4: slave address 0x10
[ 1.522088] s3c-i2c s3c2440-i2c.4: bus frequency set to 27 KHz
[ 1.527909] i2c ch[4], ack wait max time 15000(msec)
[ 1.532967] s3c-i2c s3c2440-i2c.4: i2c-4: S3C I2C adapter
[ 1.538243] INFO I2C WAIT TIme List (msec)
[ 1.542318] s3c-i2c s3c2440-i2c.5: Always Enable I2C Clock
[ 1.547873] s3c-i2c s3c2440-i2c.5: slave address 0x10
[ 1.552901] s3c-i2c s3c2440-i2c.5: bus frequency set to 19 KHz
[ 1.558723] i2c ch[5], ack wait max time 70000(msec)
[ 1.563823] s3c-i2c s3c2440-i2c.5: i2c-5: S3C I2C adapter
[ 1.569055] INFO I2C WAIT TIme List (msec)
[ 1.573128] s3c-i2c s3c2440-i2c.6: Always Enable I2C Clock
[ 1.578687] s3c-i2c s3c2440-i2c.6: slave address 0x10
[ 1.583716] s3c-i2c s3c2440-i2c.6: bus frequency set to 97 KHz
[ 1.589537] i2c ch[6], ack wait max time 5000(msec)
[ 1.594510] s3c-i2c s3c2440-i2c.6: i2c-6: S3C I2C adapter
[ 1.599783] INFO I2C WAIT TIme List (msec)
[ 1.603855] s3c-i2c s3c2440-i2c.7: Always Enable I2C Clock
[ 1.609412] s3c-i2c s3c2440-i2c.7: slave address 0x10
[ 1.614443] s3c-i2c s3c2440-i2c.7: bus frequency set to 97 KHz
[ 1.620264] i2c ch[7], ack wait max time 5000(msec)
[ 1.625188] s3c-i2c s3c2440-i2c.7: i2c-7: S3C I2C adapter
[ 1.632977] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 1.637150] Bluetooth: Core ver 2.15
[ 1.640420] NET: Registered protocol family 31
[ 1.644809] Bluetooth: HCI device and connection manager initialized
[ 1.651160] Bluetooth: HCI socket layer initialized
[ 1.656036] Switching to clocksource mct-frc
[ 1.664569] NET: Registered protocol family 2
[ 1.664685] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 1.671987] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 1.680668] TCP bind hash table entries: 65536 (order: 8, 1572864 bytes)
[ 1.688177] TCP: Hash tables configured (established 131072 bind 65536)
[ 1.692411] TCP reno registered
[ 1.695514] UDP hash table entries: 512 (order: 3, 32768 bytes)
[ 1.701485] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes)
[ 1.707985] NET: Registered protocol family 1
[ 1.716644] RPC: Registered udp transport module.
[ 1.716767] RPC: Registered tcp transport module.
[ 1.721454] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.728049] Trying to unpack rootfs image as initramfs...
[ 1.750803] Freeing initrd memory: 300K
[ 1.751007] PMU: registered new PMU device of type 0
[ 1.751279] --------------simple misc device <camw> INIT ------------------
[ 1.751822] Loaded driver for PL330 DMAC-1 s3c-pl330
[ 1.753919] DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 1.760200] Loaded driver for PL330 DMAC-2 s3c-pl330
[ 1.765053] DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 1.779595] highmem bounce pool size: 64 pages
[ 1.779768] ashmem: initialized
[ 1.787006] ROMFS MTD (C) 2007 Red Hat, Inc.
[ 1.787090] msgmni has been set to 823
[ 1.797028] alg: No test for stdrng (krng)
[ 1.797108] io scheduler noop registered
[ 1.797153] io scheduler deadline registered
[ 1.798975] io scheduler cfq registered (default)
[ 1.803967] Enable:samsung-pd.2 ++
[ 1.807065] Enable:samsung-pd.2 --
[ 1.827478] Console: switching to colour frame buffer device 160x50
[ 1.839051] FIMD src sclk = 133333333
[ 1.839103] s3cfb s3cfb.0: registered successfully
[ 1.901237] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.902218] s5pv210-uart.0: s3c2410_serial0 at MMIO 0x13800000 (irq = 16) is a S3C6400/10
[ 1.902492] s5pv210-uart.1: s3c2410_serial1 at MMIO 0x13810000 (irq = 20) is a S3C6400/10
[ 1.902769] s5pv210-uart.2: s3c2410_serial2 at MMIO 0x13820000 (irq = 24) is a S3C6400/10
[ 1.909964] s5pv210-uart.3: s3c2410_serial3 at MMIO 0x13830000 (irq = 28) is a S3C6400/10
[ 1.918117] s5pv210-uart.4: s3c2410_serial4 at MMIO 0x13840000 (irq = 320) is a S3C6400/10
[ 1.929489] brd: module loaded
[ 1.931086] loop: module loaded
[ 1.932397] pmem: 0 init
[ 1.936148] pmem_gpu1: 0 init
[ 1.938412] [powercontrol] driver initialized
[ 1.942158] ======================== HAAM375 I2C Driver ADD ==============================
[ 1.950543] input: haam375 as /devices/virtual/input/input0
[ 1.955960] haam375_i2c_probe :: 409 :: haam375
[ 1.960642] haam375_i2c_probe :: 411 :: 0x01
[ 1.969148] ======================== HAAM375 MODE is 00 ==============================
[ 1.975153] ======================== HAAM375 CONTROL REGISTER is 00 ==============================
[ 1.981950] ============= tdmk_temp INIT =============
[ 1.987281] input: tdmk_temp_sensor as /devices/virtual/input/input1
[ 1.993884] usbcore: registered new interface driver catc
[ 1.998752] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
[ 2.004682] usbcore: registered new interface driver kaweth
[ 2.010207] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[ 2.017709] usbcore: registered new interface driver pegasus
[ 2.023322] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver
[ 2.030199] usbcore: registered new interface driver rtl8150
[ 2.035814] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.042456] s5p-ehci s5p-ehci: s5pv210 EHCI
[ 2.046539] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[ 2.053613] s5p-ehci s5p-ehci: irq 134, io mem 0x12580000
[ 2.065329] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
[ 2.065443] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.071057] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.078257] usb usb1: Product: s5pv210 EHCI
[ 2.082423] usb usb1: Manufacturer: Linux 2.6.35.8-v2.03-20190111 ehci_hcd
[ 2.089279] usb usb1: SerialNumber: s5pv210
[ 2.093774] hub 1-0:1.0: USB hub found
[ 2.097192] hub 1-0:1.0: 3 ports detected
[ 2.101414] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.107382] [usb_host_phy_init]Already power on PHY
[ 2.112206] s5p-ohci s5p-ohci: s5pv210 OHCI
[ 2.116379] s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2
[ 2.123407] s5p-ohci s5p-ohci: irq 134, io mem 0x12590000
[ 2.184382] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.184457] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.184534] usb usb2: Product: s5pv210 OHCI
[ 2.184580] usb usb2: Manufacturer: Linux 2.6.35.8-v2.03-20190111 ohci_hcd
[ 2.187110] usb usb2: SerialNumber: s5pv210
[ 2.191564] hub 2-0:1.0: USB hub found
[ 2.194992] hub 2-0:1.0: 3 ports detected
[ 2.199237] Initializing USB Mass Storage driver...
[ 2.203933] usbcore: registered new interface driver usb-storage
[ 2.209848] USB Mass Storage support registered.
[ 2.214482] usbcore: registered new interface driver ums-alauda
[ 2.220384] usbcore: registered new interface driver ums-cypress
[ 2.226380] usbcore: registered new interface driver ums-datafab
[ 2.232362] usbcore: registered new interface driver ums-isd200
[ 2.238264] usbcore: registered new interface driver ums-sddr09
[ 2.244166] usbcore: registered new interface driver ums-sddr55
[ 2.250068] usbcore: registered new interface driver ums-usbat
[ 2.255952] s3c-udc : S3C HS USB OTG Device Driver,(c) 2008-2009 Samsung Electronics
[ 2.255957] s3c-udc : version 15 March 2009 (DMA Mode)
[ 2.268699] android init
[ 2.271252] android_probe pdata: c05ef858
[ 2.275235] android_bind
[ 2.277860] android_usb gadget: android_usb ready
[ 2.282414] Registered gadget driver 'android_usb'
[ 2.289290] f_adb init
[ 2.289508] android_register_function adb
[ 2.293521] f_mass_storage init
[ 2.296680] fsg_probe pdev: c05eecf8, pdata: c05ef87c
[ 2.301711] android_register_function usb_mass_storage
[ 2.306801] f_rndis init
[ 2.309357] android_register_function rndis
[ 2.313489] rndis_function_bind_config MAC: 00:00:00:00:00:00
[ 2.319232] android_usb gadget: using random self ethernet address
[ 2.325390] android_usb gadget: using random host ethernet address
[ 2.331794] usb0: MAC fe:28:ea:6f:41:e2
[ 2.335362] usb0: HOST MAC f2:e6:0f:9e:b9:df
[ 2.339807] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 2.346473] android_usb gadget: Number of LUNs=1
[ 2.351070] lun0: LUN: removable file: (no medium)
[ 2.355985] adb_bind_config
[ 2.359430] sis_ts_init
[ 2.361244] sis_ts_probe
[ 2.363911] cmd [0x0] => unknow data:[0x0][0x0][0x0][0x0][0x0][0x0][0x0][0x0][0x0][0x0][0x0][0x0][0x0][0x0][0x0][0x0]
[ 2.374224] Wrong response format!
[ 2.377636] sis_i2c_ts: probe of 1-0005 failed with error -1
[ 2.383306] ==ft5x0x_ts_init==
[ 2.386333] [FTS] ft5x0x_ts_probe, driver version is 3.0.
[ 2.391825] msg ft5x0x_read_reg i2c read error: -6
[ 2.396500] ret=0
[ 2.398382] [sis_ts_get_fwversion] TSP-FW Version :
[ 2.403457] msg ft5x0x_read_reg i2c read error: -6
[ 2.408095] [MMS100] melfas_ts_probe
[ 2.412565] [MMS100] HW Revision:4(4h), SW Version:6(6h)
[ 2.417078] input: mms100ts as /devices/platform/s3c2440-i2c.1/i2c-1/1-0048/input/input2
[ 2.425166] melfas_ts_probe:934 ---------------------> IRQ num = 351
[ 2.431366] =======================> [melfas_touch_power_enable:116] <==========================
[ 2.545344] usb 1-1: new high speed USB device using s5p-ehci and address 2
[ 2.675691] usb 1-1: New USB device found, idVendor=0424, idProduct=2513
[ 2.675765] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.676273] hub 1-1:1.0: USB hub found
[ 2.676438] hub 1-1:1.0: 3 ports detected
[ 2.700336] =====> IRQ value: 1
[ 2.810562] [MMS100] melfas_ts_probe: Start touchscreen. name: mms100ts, irq: 351
[ 2.810983] S3C24XX RTC, (c) 2004,2006 Simtec Electronics
[ 2.811102] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 2.811398] using rtc device, s3c, for alarms
[ 2.811463] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
[ 2.817034] -----------------1
[ 2.820064] i2c /dev entries driver
[ 2.824467] Linux video capture interface: v2.00
[ 2.828190] Initialize JPEG driver
[ 2.831755] i2c i2c-5: attached s5p_ddc into i2c adapter successfully
[ 2.837966] S5P HPD Driver, (c) 2009 Samsung Electronics
[ 2.843380] [HPD_IF] s5p_hpd_irq_handler: EINT HPD interrupt
[ 2.848968] S5P CEC Driver, (c) 2009 Samsung Electronics
[ 2.854617] sysmmu_set_tablebase: CP15 TTBR0 : 0x40004000
[ 2.859548] sysmmu_set_tablebase: SYSMMU_G2D sysmmuconp->regs + S5P_PT_BASE_ADDR:0xE81A0014
[ 2.867884] sysmmu_on:SYSMMU_G2D sysmmuconp->regs + S5P_MMU_CTRL:0xE81A0000, reg:0x5
[ 2.875737] mfc_init_pm dev_name(pm->device)) : s3c-mfc
[ 2.880813] mfc_cpufreq_register dev_name(pm->device)) : s3c-mfc
[ 2.888536] MFC F/W loaded for first Instance successfully (size: 353532)
[ 2.893822] MFC(Multi Function Codec - FIMV v5.x) registered successfully
[ 2.900618] Mali: init_mali_clock mali_clock c05e4bf8
[ 2.907851] Enable:samsung-pd.1 ++
[ 2.908831] Enable:samsung-pd.1 --
[ 2.913447] Mali: Mali device driver loaded
[ 2.916533] max17040_probe++
[ 2.923408] =======================
[ 2.923412] MAX17040 volt : 387500uV (0x09b0)
[ 2.923416] =======================
[ 2.934699] max17040_probe Set max17040_fuel_gauge
[ 2.942532] max17040 5-0036: MAX17040 Fuel-Gauge Ver 02
[ 2.944535] max17040_probe g_charge_mode : 0
[ 2.944849] max17040_probe g_nSuspendNotifyDisable : 0 ,g_nSuspendFlag : 0
[ 2.951761] max17040_probe--
[ 2.954755] tdmk_battery_probe++
[ 2.957943] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=1, tdmk_get_charge_mode = 0
[ 2.968687] tdmk_battery_probe--
[ 2.971994] s3c-hwmon: attached driver
[ 2.975665] device-mapper: uevent: version 1.0.3
[ 2.980462] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: [email protected]
[ 2.988797] device-mapper: multipath: version 1.1.1 loaded
[ 2.990497] usb 1-1.2: new full speed USB device using s5p-ehci and address 3
[ 3.001207] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 3.007900] cpuidle: using governor ladder
[ 3.011925] cpuidle: using governor menu
[ 3.015709] sdhci: Secure Digital Host Controller Interface driver
[ 3.021890] sdhci: Copyright(c) Pierre Ossman
[ 3.026251] s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (100000000 Hz)
[ 3.033108] mmc0: no vmmc regulator found
[ 3.038187] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
[ 3.044118] s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (88888888 Hz)
[ 3.050889] mmc1: no vmmc regulator found
[ 3.055966] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
[ 3.061910] s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (88888888 Hz)
[ 3.068675] mmc2: no vmmc regulator found
[ 3.073756] mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
[ 3.079671] sdhci_s3c_probe:619: initialize to restore function for s3c_device_hsmmc3
[ 3.088115] usbcore: registered new interface driver usbhid
[ 3.093039] usbhid: USB HID core driver
[ 3.097182] logger: created 64K log 'log_main'
[ 3.101358] logger: created 256K log 'log_events'
[ 3.106085] logger: created 64K log 'log_radio'
[ 3.110581] logger: created 64K log 'log_system'
[ 3.116046] No device for DAI ALC5625 HiFi
[ 3.119166] No device for DAI ALC5625 Voice
[ 3.123556] ALC5625 Audio Codec 0.03 alsa 1.0.23
[ 3.129238] asoc: ALC5625 HiFi <-> s3c64xx-i2s-v4 mapping ok
[ 3.129452] mmc0: Enable 8Bit Data bus. ##
[ 3.130498] mmc0: new high speed MMC card at address 0001
[ 3.130716] mmcblk0: mmc0:0001 SEM08G 7.39 GiB
[ 3.147714] mmcblk0:
[ 3.158547] usb 1-1.2: New USB device found, idVendor=1fc9, idProduct=010b
[ 3.158625] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.164101] usb 1-1.2: Product: PR533
[ 3.164109] Disable:samsung-pd.1 ++
[ 3.164119] Disable:samsung-pd.1 --
[ 3.164146] p1 p2 p3 p4
[ 3.177205] usb 1-1.2: Manufacturer: NXP
[ 3.181057] usb 1-1.2: SerialNumber: 3.60
[ 3.218533] alc5625: initial ok
[ 3.220856] ALSA device list:
[ 3.220892] #0: origen (ALC5625)
[ 3.220938] Netfilter messages via NETLINK v0.30.
[ 3.221007] nf_conntrack version 0.5.0 (12683 buckets, 50732 max)
[ 3.221208] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 3.223840] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 3.231763] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 3.237997] ctnetlink v0.93: registering with nfnetlink.
[ 3.243269] IPv4 over IPv4 tunneling driver
[ 3.247824] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.252785] arp_tables: (C) 2002 David S. Miller
[ 3.257331] TCP cubic registered
[ 3.260508] NET: Registered protocol family 17
[ 3.264946] Bridge firewalling registered
[ 3.269036] Bluetooth: L2CAP ver 2.14
[ 3.272567] Bluetooth: L2CAP socket layer initialized
[ 3.277675] Bluetooth: RFCOMM TTY layer initialized
[ 3.282462] Bluetooth: RFCOMM socket layer initialized
[ 3.287583] Bluetooth: RFCOMM ver 1.11
[ 3.291315] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.296610] Bluetooth: BNEP filters: protocol multicast
[ 3.301818] ++ s5pv310_cpufreq_init
[ 3.305361] -- s5pv310_cpufreq_init
[ 3.308855] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 2
[ 3.320766] s3c-rtc s3c64xx-rtc: setting system clock to 2000-01-01 16:40:10 UTC (946744810)
[ 3.324881] ctrl->mem.size = 0x7d0000
[ 3.328456] ctrl->mem.base = 0x5c6c0000
[ 3.332546] FIMC0 registered successfully
[ 3.336454] ctrl->mem.size = 0xc00000
[ 3.339906] ctrl->mem.base = 0x5ce90000
[ 3.343908] FIMC1 registered successfully
[ 3.348023] ctrl->mem.size = 0x1800000
[ 3.351470] ctrl->mem.base = 0x5da90000
[ 3.355444] FIMC2 registered successfully
[ 3.359412] ctrl->mem.size = 0x300000
[ 3.362926] ctrl->mem.base = 0x5f290000
[ 3.366896] FIMC3 registered successfully
[ 3.370927] S5P TVOUT Driver v3.0 (c) 2010 Samsung Electronics
[ 3.376766] ===========================> HDMI_CTRL_PHY_POWER: 1 <=====================
[ 3.384456] Enable:samsung-pd.4 ++
[ 3.387830] Enable:samsung-pd.4 --
[ 3.439603] mmc2: new high speed SDIO card at address 0001
[ 3.508179] ===========================> HDMI_CTRL_PHY_POWER: 0 <=====================
[ 3.513148] s5p_hdmi_ctrl_phy_power:1665 -------------------------------------> got mutex
[ 3.513237] s5p_hdmi_ctrl_phy_power:1670 -------------------------------------> free mutex
[ 3.514612] Disable:samsung-pd.4 ++
[ 3.514657] Disable:samsung-pd.4 --
[ on early-init ]
[ on init ]
[ on early-fs ]
[ on fs ]
[ service setup_fs ]
[ on post-fs ]
[ on boot ]
[ service ueventd ]
[ service console ]
[ on property:ro.secure=0 ]
[ service adbd ]
[ on property:ro.kernel.qemu=1 ]
[ on property:persist.service.adb.enable=1 ]
[ on property:persist.service.adb.enable=0 ]
[ service servicemanager ]
[ service vold ]
[ service netd ]
[ service debuggerd ]
[ service zygote ]
[ service media ]
[ service bootanim ]
[ service dbus ]
[ service bluetoothd ]
[ service hfag ]
[ service hsag ]
[ service opush ]
[ service pbap ]
[ service installd ]
[ service racoon ]
[ service mtpd ]
[ service keystore ]
[ service dumpstate ]
[ service tdmkmiscserver ]
[ on boot ]
[ service setregioncode ]
[ service setdeepsleep ]
[ service dhcpcd_mlan0 ]
[ service iprenew_mlan0 ]
[ service wpa_supplicant ]
[ service tdmkdrvloader ]
[tdmk_call_fireman:954] not found usb storage.
[ 4.732555] init: cannot open '/initlogo.rle'
[ 4.832491] EXT4-fs (mmcblk0p1): recovery complete
[ 4.833927] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[ 4.844448] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.863687] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 4.900813] EXT4-fs (mmcblk0p3): recovery complete
[ 4.902244] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
[ 5.282703] EXT4-fs (mmcblk0p4): warning: mounting fs with errors, running e2fsck is recommended
[ 5.285081] EXT4-fs (mmcblk0p4): recovery complete
[ 5.286510] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
[ 5.372981] init: cannot find '/system/bin/tdmk.sh', disabling 'tdmkdrvloader'
[ 5.615894] mlan: module license 'Marvell Proprietary' taints kernel.
[ 5.615975] Disabling lock debugging due to kernel taint
[ 6.515918] warning: `wpa_supplicant' uses 32-bit capabilities (legacy support in use)
[ 6.787780] TDMK misc driver v2.03-20190111
[ 6.787833] TDMK : set usb_backup_restore__need
[ 6.788833] [sis_ts_get_fwversion] TSP-FW Version :
[ 6.788845] tdmk__monitoring_thread_func(0ms) run.
[ 6.789085] msg ft5x0x_read_reg i2c read error: -6
[ 6.789141] 2 [mms100_ts_get_fwversion] TSP-FW Version : MMS100-4-6
[ 7.395271] s3c_dma_close++++++++++++++++++++++++++++++++++++++
[ 7.395346] s3c_dma_close total dma_use_count[0]
[ 7.395398] s3c_dma_close total dma_disable_wait_count[0]
[ 7.395458] s3c_dma_close--------------------------------------
[ 7.395946] s3c_dma_close++++++++++++++++++++++++++++++++++++++
[ 7.400878] s3c_dma_close total dma_use_count[0]
[ 7.405287] s3c_dma_close total dma_disable_wait_count[0]
[ 7.412111] s3c_dma_close--------------------------------------
[ 7.422023] .....................gpz2 configuration: 0x02222222
[ 7.422459] P:DmaAddr=@67280000 Total=16384bytes PrdSz=4096 #Prds=4, dmaEnd 0x67284000
[ 7.449840] alc5625_write ok, reg = 84, value = f0
[ 7.449895] enter spk_pga_event
[ 7.449936] after virtual spk power up!
[ 7.456719] enter spk_pga_event
[ 7.456760] after virtual spk power up!
[ 7.460434] s3c_dma_close++++++++++++++++++++++++++++++++++++++
[ 7.460505] s3c_dma_close total dma_use_count[0]
[ 7.460557] s3c_dma_close total dma_disable_wait_count[0]
[ 7.464932] s3c_dma_close--------------------------------------
[ 7.471457] s3c_dma_close++++++++++++++++++++++++++++++++++++++
[ 7.476735] s3c_dma_close total dma_use_count[0]
[ 7.481306] s3c_dma_close total dma_disable_wait_count[0]
[ 7.486718] s3c_dma_close--------------------------------------
[ 7.493126] s3c_dma_close++++++++++++++++++++++++++++++++++++++
[ 7.498523] s3c_dma_close total dma_use_count[0]
[ 7.503110] s3c_dma_close total dma_disable_wait_count[0]
[ 7.508500] s3c_dma_close--------------------------------------
[ 7.525845] .....................gpz2 configuration: 0x02222222
[ 7.525918] P:DmaAddr=@67280000 Total=16384bytes PrdSz=4096 #Prds=4, dmaEnd 0x67284000
[ 7.528775] s3c_dma_close++++++++++++++++++++++++++++++++++++++
[ 7.534110] s3c_dma_close total dma_use_count[0]
[ 7.538703] s3c_dma_close total dma_disable_wait_count[0]
[ 7.544089] s3c_dma_close--------------------------------------
[ 7.975711] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=2, tdmk_get_charge_mode = 0
[ 8.518145] BT FW is active(5)
[ 8.529460] BT FW is active(0)
[ 8.529497] BT: FW already downloaded!
[ 8.552705] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 8.978448] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 8.978571] ================================= tdmk_set_battery_charger : Off============================
[ 8.978678] tdmk_force_charge_off g_charge_mode : 0
[ 9.980500] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 10.980503] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 11.867651] s3c-fimc3: FIMC3 1 opened.
[ 11.867808] [HPD_IF] s5p_hpd_ioctl: HPD status is unplugged
[ 12.554411] alc5625_write ok, reg = 84, value = 0
[ 12.554469] enter spk_pga_event
[ 12.554510] aftet virtual spk power down!
[ 12.556813] enter spk_pga_event
[ 12.556852] aftet virtual spk power down!
[ 12.987221] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 13.642106] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 13.763894] enabling adb
[ 13.764280] adb_open
[ 13.791904] Enable:samsung-pd.1 ++
[ 13.791957] Enable:samsung-pd.1 --
# [ 13.995466] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 14.230811] Disable:samsung-pd.1 ++
[ 14.230860] Disable:samsung-pd.1 --
[ 14.260940] Enable:samsung-pd.1 ++
[ 14.260996] Enable:samsung-pd.1 --
[ 14.525414] Disable:samsung-pd.1 ++
[ 14.525464] Disable:samsung-pd.1 --
[ 15.005600] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 16.275088] Enable:samsung-pd.1 ++
[ 16.275138] Enable:samsung-pd.1 --
[ 16.544249] Disable:samsung-pd.1 ++
[ 16.544296] Disable:samsung-pd.1 --
[ 17.007488] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 17.794850] =======================
[ 17.794854] MAX17040 volt : 9895000uV (0xf760)
[ 17.794857] =======================
[ 17.799056] [BATT_ERR][0] recal_vol_cur=9895, percent=100
[ 18.007632] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 18.055092] WLAN FW already running! Skip FW download
[ 18.055178] WLAN FW is active(121207_04)
[ 18.118636] [tdmk_power_manager] DO NOT LCD ON
[ 18.118713] [tdmk_power_manager] TDMK_POWERMGR__CPU_LOW(1000000HZ -> 1GHz)
[ 18.278225] Enable:samsung-pd.1 ++
[ 18.278276] Enable:samsung-pd.1 --
[ 18.339864] request_suspend_state: wakeup (3->0) at 17789555627 (2000-01-01 16:40:25.510750293 UTC)
[ 18.343832] ================================= Sensor ON 2 ============================
[ 18.541719] Disable:samsung-pd.1 ++
[ 18.541771] Disable:samsung-pd.1 --
[ 18.814900] Enable:samsung-pd.1 ++
[ 18.814956] Enable:samsung-pd.1 --
[ 19.007708] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 19.071710] Disable:samsung-pd.1 ++
[ 19.071760] Disable:samsung-pd.1 --
[ 20.010612] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 20.281333] Enable:samsung-pd.1 ++
[ 20.281385] Enable:samsung-pd.1 --
[ 20.555439] Disable:samsung-pd.1 ++
[ 20.555487] Disable:samsung-pd.1 --
[ 21.010611] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 21.329641] Adding 204796k swap on /data/swapfile. Priority:-1 extents:12 across:385020k SS
[ 21.543107] Enable:samsung-pd.1 ++
[ 21.543159] Enable:samsung-pd.1 --
[ 21.810598] Disable:samsung-pd.1 ++
[ 21.810649] Disable:samsung-pd.1 --
[ 22.020738] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 22.158419] ================================= tdmk_set_battery_charger : On============================
[ 22.158533] max17040_setMaxChargePercent g_max_charge_percent : 100
[ 22.165734] max17040_getChargeOffTime g_charge_off_time: 0
[ 22.168706] max17040_setChargeOffTime g_charge_off_time : 3600000
[ 22.172068] tdmk_force_charge_on g_charge_mode : 2
[ 22.173929] max17040_setDropVoltageLimit g_nDropVoltageLimit : 9000000
[ 22.177044] max17040_setDropCheckTime g_nDropCheckTime : 10
[ 22.184262] max17040_setFullChageCountLimit g_nFullychargedCountLimit : 10 x 2
[ 22.197940] max17040_setErrorCountLimit g_nErrorCntLimit : 3
[ 22.202689] max17040_setLockChargeOff g_nAlwaysOff: 0
[ 22.206356] max17040_setErrorCheckTime g_nErrorCheckTime : 5
[ 22.322505] STATUS>> GSensor set Calibration cal[x] = 1(0x01),[y] = -6(0xfa),[z] = -2(0xfe)
[ 22.502796] Enable:samsung-pd.1 ++
[ 22.502848] Enable:samsung-pd.1 --
[ 23.022947] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=1, tdmk_get_charge_mode = 2
[ 23.030543] =======================
[ 23.030547] MAX17040 volt : 22500uV (0x0090)
[ 23.030550] =======================
[ 23.670594] Disable:samsung-pd.1 ++
[ 23.670644] Disable:samsung-pd.1 --
[ 25.020480] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=2, tdmk_get_charge_mode = 2
[ 26.020482] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 2
[ 26.020608] ================================= tdmk_set_battery_charger : Off============================
[ 26.020713] tdmk_force_charge_off g_charge_mode : 0
[ 26.032399] Enable:samsung-pd.1 ++
[ 26.032453] Enable:samsung-pd.1 --
[ 26.035522] max17040_getChargeOffTime g_charge_off_time: 3600000
[ 26.041686] max17040_getChargeOffTime g_charge_off_time: 3600000
[ 26.285417] Disable:samsung-pd.1 ++
[ 26.285464] Disable:samsung-pd.1 --
[ 27.020511] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 28.021218] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 29.025275] =======================
[ 29.025279] MAX17040 volt : 10020000uV (0xfa80)
[ 29.025283] =======================
[ 29.029575] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 29.038606] max17040_getChargeOffTime g_charge_off_time: 3600000
[ 29.042612] max17040_getChargeOffTime g_charge_off_time: 3600000
[ 31.020486] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 32.020493] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 33.020494] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 34.021362] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 35.025247] =======================
[ 35.025250] MAX17040 volt : 10237500uV (0xfff0)
[ 35.025254] =======================
[ 35.029556] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 35.039182] max17040_getChargeOffTime g_charge_off_time: 3600000
[ 35.055880] max17040_getChargeOffTime g_charge_off_time: 3600000
[ 37.025472] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 39.025473] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 40.025481] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 41.030479] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 41.035243] =======================
[ 41.035246] MAX17040 volt : 10237500uV (0xfff0)
[ 41.035250] =======================
[ 42.030485] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 43.157258] Enable:samsung-pd.1 ++
[ 43.157310] Enable:samsung-pd.1 --
[ 44.025551] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 44.461263] Disable:samsung-pd.1 ++
[ 44.461315] Disable:samsung-pd.1 --
[ 45.026194] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 46.026222] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 47.031179] =======================
[ 47.031183] MAX17040 volt : 10237500uV (0xfff0)
[ 47.031186] =======================
[ 47.035462] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 49.025505] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 50.025509] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 51.025510] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 52.025513] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 53.025620] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 53.043054] =======================
[ 53.043058] MAX17040 volt : 10237500uV (0xfff0)
[ 53.043061] =======================
[ 54.029532] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 54.175878] Enable:samsung-pd.1 ++
[ 54.175930] Enable:samsung-pd.1 --
[ 55.415425] Disable:samsung-pd.1 ++
[ 55.415472] Disable:samsung-pd.1 --
[ 56.025609] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 56.487160] Enable:samsung-pd.1 ++
[ 56.487211] Enable:samsung-pd.1 --
[ 56.587524] .....................gpz2 configuration: 0x02222222
[ 56.587601] P:DmaAddr=@67280000 Total=16384bytes PrdSz=4096 #Prds=4, dmaEnd 0x67284000
[ 56.592861] alc5625_write ok, reg = 84, value = f0
[ 56.592921] enter spk_pga_event
[ 56.592969] after virtual spk power up!
[ 56.595105] enter spk_pga_event
[ 56.595153] after virtual spk power up!
[ 56.599208] s3c2410_dma_request ch->id:16, id_use:0 0xc05e5208 Enable usage:0++
[ 56.605015] s3c2410_dma_request ch->id:16, id:1 0xc05e5208 Enable usage:1--
[ 57.026308] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 57.825426] Disable:samsung-pd.1 ++
[ 57.825474] Disable:samsung-pd.1 --
[ 58.026488] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 59.030160] =======================
[ 59.030163] MAX17040 volt : 10237500uV (0xfff0)
[ 59.030167] =======================
[ 59.034430] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 59.964048] s3c2410_dma_free+
[ 59.964096] tm10_dma_disable_wait[16]:1
[ 59.964140] s3c2410_dma_free-
[ 59.964431] s3c_dma_close++++++++++++++++++++++++++++++++++++++
[ 59.964497] s3c_dma_close total dma_use_count[1]
[ 59.964548] s3c_dma_close total dma_disable_wait_count[1]
[ 59.967437] s3c_dma_close++ 0xc05e5208 usage:1 clk_id:2===========
[ 59.973546] s3c_dma_close DMA Clk Disable[16] (usage:1 clk_id:2 get_tm10_dma_use[1])++
[ 59.981446] s3c_dma_close DMA Clk Disable[16] (usage:0 clk_id:2 get_tm10_dma_use[0] get_tm10_dma_disable_wait[0])--
[ 59.991857] s3c_dma_close total dma_use_count[0]
[ 59.996455] s3c_dma_close total dma_disable_wait_count[0]
[ 60.001973] s3c_dma_close-- DMA Clk Disable--usage:0===========
[ 60.007745] s3c_dma_close--------------------------------------
[ 61.025481] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 62.026073] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 62.641891] Enable:samsung-pd.1 ++
[ 62.641942] Enable:samsung-pd.1 --
[ 62.674985] .....................gpz2 configuration: 0x02222222
[ 62.675060] P:DmaAddr=@67280000 Total=16384bytes PrdSz=4096 #Prds=4, dmaEnd 0x67284000
[ 62.675464] s3c2410_dma_request ch->id:16, id_use:0 0xc05e5208 Enable usage:0++
[ 62.675549] s3c2410_dma_request ch->id:16, id:1 0xc05e5208 Enable usage:1--
[ 63.026095] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 63.900551] Disable:samsung-pd.1 ++
[ 63.900600] Disable:samsung-pd.1 --
[ 64.026278] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 65.030194] =======================
[ 65.030197] MAX17040 volt : 10237500uV (0xfff0)
[ 65.030201] =======================
[ 65.034497] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 65.939401] s3c2410_dma_free+
[ 65.939450] tm10_dma_disable_wait[16]:1
[ 65.939494] s3c2410_dma_free-
[ 65.939779] s3c_dma_close++++++++++++++++++++++++++++++++++++++
[ 65.939844] s3c_dma_close total dma_use_count[1]
[ 65.939895] s3c_dma_close total dma_disable_wait_count[1]
[ 65.942794] s3c_dma_close++ 0xc05e5208 usage:1 clk_id:2===========
[ 65.948913] s3c_dma_close DMA Clk Disable[16] (usage:1 clk_id:2 get_tm10_dma_use[1])++
[ 65.956812] s3c_dma_close DMA Clk Disable[16] (usage:0 clk_id:2 get_tm10_dma_use[0] get_tm10_dma_disable_wait[0])--
[ 65.967228] s3c_dma_close total dma_use_count[0]
[ 65.971821] s3c_dma_close total dma_disable_wait_count[0]
[ 65.977206] s3c_dma_close-- DMA Clk Disable--usage:0===========
[ 65.983106] s3c_dma_close--------------------------------------
[ 67.025497] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 68.025500] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 69.026141] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 70.026156] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 70.992937] alc5625_write ok, reg = 84, value = 0
[ 70.992994] enter spk_pga_event
[ 70.993036] aftet virtual spk power down!
[ 70.995365] enter spk_pga_event
[ 70.995404] aftet virtual spk power down!
[ 71.030154] =======================
[ 71.030158] MAX17040 volt : 10237500uV (0xfff0)
[ 71.030162] =======================
[ 71.034433] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 73.025556] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 74.026236] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 75.026268] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 76.026336] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 77.030205] =======================
[ 77.030209] MAX17040 volt : 10237500uV (0xfff0)
[ 77.030212] =======================
[ 77.034497] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 78.372993] Enable:samsung-pd.1 ++
[ 78.373045] Enable:samsung-pd.1 --
[ 79.025495] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 79.585424] Disable:samsung-pd.1 ++
[ 79.585471] Disable:samsung-pd.1 --
[ 80.025494] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 81.025500] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 82.026342] tdmk_battery_get_property g_nErrorCheckTime = 5,g_nErrorCntLimit =3 ,ERROR Count=3, tdmk_get_charge_mode = 0
[ 82.209267] [MMS100] tsp_chk_show Version Check++
[ 82.210341] [MMS100] HW Revision:4(4h), SW Version:6(6h)
[ 82.210400] [MMS100] tsp_chk_show Version Check : OK
[ 82.210455] [MMS100] tsp_chk_show Version Check--
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment