Getting NordVPN WireGuard details

GetNordVPNWireGuardDetails.md

About

Instructions to obtain WireGuard details of your NordVPN account. These can be used to setup a WireGuard tunnel on your router to NordVPN.

Source: https://forum.gl-inet.com/t/configure-wireguard-client-to-connect-to-nordvpn-servers/10422/27

Prerequisites

If you have any linux machine, use that or install a vm if you don't have one.

Get their official linux app installed. Make sure you have wireguard installed too. And set the used technology to Nordlynx by running nordvpn set technology nordlynx

Fetching details

Connect to nordvpn with command: nordvpn connect (don't forget to login with nordvpn login --legacy).

Fetch (your) IP address

After successful connection run

ifconfig nordlynx

Fetch your private key

Run

sudo wg show nordlynx private-key

Output of this command should be something like this:

CKMAE9LARlt2eZHgGnNaSUYiKllKJN7f3hed/bWm5E8=

The key above is just a random key for demo purposes.

Fetch your public key

Run

sudo wg show nordlynx public-key

Output of this command should be something like this:

TO158iXbNXt2eZHgGnNaSUYiKZHgGN7f3hed/bWm5E8=

The key above is just a random key for demo purposes.

Fetch server details

Make sure you have curl and jq installed on your host/router. These are needed to be able to fetch the config of NordVPN Server. If not installed, go ahead and install

opkg install curl jq

After installation enter the command below to fetch the recommended server config:

curl -s "https://api.nordvpn.com/v1/servers/recommendations?&filters\[servers_technologies\]\[identifier\]=wireguard_udp&limit=1"|jq -r '.[]|.hostname, .station, (.locations|.[]|.country|.city.name), (.locations|.[]|.country|.name), (.technologies|.[].metadata|.[].value), .load'

Output:

uk1818.nordvpn.com #your endpoint host
178.239.166.185 #its ip address
London #city
United Kingdom #country
K53l2wOIHU3262sX5N/5kAvCvt4r55lNui30EbvaDlE= #Server public key
10 #Server load at the time.

Or just visit the following url https://api.nordvpn.com/v1/servers/recommendations?&filters\[servers_technologies\]\[identifier\]=wireguard_udp&limit=1 from your browser and look for the details manually.

Hi, did anyone configured the Wireguard VPN with Fritzbox or has any hint on what could make it go wrong?? I have a 7590 and I can't make it work. I always get:

Unfortunately, it was not possible to apply your settings.
Imported configuration file of WireGuard remote site was defective.
Click on "Close" to go to the WireGuard® overview and set up the WireGuard® connection again.

My .conf looks like (thanks @dvcrn):

[Interface]
PrivateKey=I_am_not_showing_it= (got this after I got a token from nordvpn and used: https://nord-configs.onrender.com/ )
Address=10.5.0.2/32
DNS=8.8.8.8

[Peer]
PublicKey=5p4RkybdRU5uaDi90eu4KZPTFif0lKCg4Qp6t1c4F30=
AllowedIPs=0.0.0.0/0,::/0
Endpoint=nl757.nordvpn.com:51820

I can't understand what it does not like. The event viewer (not the greatest log) shows that a VPN was configured succesfully.
@DarkGamer7798 how did you make it work? I am following your steps to the letter, with no success. Also with whatever deviation I could think of, I still have no success and nothing tells me what is wrong or what it does not like.
Any hint would be appreciated.