ARX-3303 renew procedure

arx3303_renew.md

Board 1.0

from top to bottom

*Serial

• Debug
• A
• B
• I For digging data, you should try Debug port first.

Check files

• have /etc/config/sysbase.cfg
• have /usr/sbin/sysbase.sh

#!/bin/sh
cat /etc/sysbase.cfg

• modify /etc/init.d/frsinit.sh

. /etc/sysbase.cfg
ip link set eth1 address $hwaddr

• update /usr/sbin/flxredsv
• have /etc/init.d/shelld

cd /etc/rcS.d
ln -s ../init.d/shelld S41shelld

In /home/root

• install redcor
• install webdist
• install arxcli

Others:

• have /etc/init.d/mmsd
• copy /usr/local/sbin/mmsd
• copy /usr/bin/socat
• copy /usr/sbin/sysbase.sh
• copy /etc/init.d/networking (ensure interface lo is there)
• rm -rf /home/root/altera
• copy /usr/sbin/flxredsv
• copy phyrw and ensure it can write phy

phyrw 0 16 3
phyrw 0 16

• have /etc/init.d/setupgpios.sh (https://github.com/Intrising/HSR-PRP/wiki/linux-setup-gpio)

update kernel under linux

flashcp -v /tmp/zImage /dev/mtd4

at bootloader. set bootimagesize to image length in hex

 set bootimagesize 2ec1d8

• have /usr/sbin/writek.sh

#!/bin/sh
flashcp -v $1 /dev/mtd4
fsize=`wc -c $1 | awk '{print $1}'`
printf -v hexsize "%x" "$fsize"       
echo "remember set bootimagesize to $hexsize"

devel mode

console=ttyS0,115200 debug

• got 1 with reddot

U-Boot SPL 2013.01.01 (Nov 03 2014 - 18:13:20)
BOARD : Altera SOCFPGA Cyclone V Board
SDRAM: Initializing MMR registers
SDRAM: Calibrating PHY
SEQ.C: Preparing to start memory calibration
SEQ.C: CALIBRATION PASSED
SF: Read data capture delay calibrated to 3 (0 - 6)
SF: Detected MX66L51235L with page size 65536, total: 16777216


U-Boot 2013.01.01 (Nov 28 2014 - 13:54:23)

CPU   : Altera SOCFPGA Platform
BOARD : Altera SOCFPGA Cyclone V Board
DRAM:  1 GiB
MMC:   ALTERA DWMMC: 0
SF: Read data capture delay calibrated to 3 (0 - 6)
SF: Detected MX66L51235L with page size 65536, total: 67108864
In:    serial
Out:   serial
Err:   serial
Net:   mii0
Hit any key to stop autoboot:  0
SF: Detected MX66L51235L with page size 65536, total: 67108864
altera_load: Failed with error code -4
## Starting application at 0x3FF861BC ...
## Application terminated, rc = 0xA
fpgaintf
ffd08028: 00000000    ....
fpga2sdram
ffc25080: 00000000    ....
axibridge
ffd0501c: 00000000    ....
SF: Detected MX66L51235L with page size 65536, total: 67108864
Bad Linux ARM zImage magic!
SOCFPGA_CYCLONE5 #

I got newer from archiver2

U-Boot SPL 2013.01.01 (Apr 23 2015 - 09:20:36)
BOARD : Altera SOCFPGA Cyclone V Board
CLOCK: EOSC1 clock 25000 KHz
CLOCK: EOSC2 clock 25000 KHz
CLOCK: F2S_SDR_REF clock 0 KHz
CLOCK: F2S_PER_REF clock 0 KHz
CLOCK: MPU clock 925 MHz
CLOCK: DDR clock 400 MHz
CLOCK: UART clock 100000 KHz
CLOCK: MMC clock 50000 KHz
CLOCK: QSPI clock 370000 KHz
RESET: COLD
SDRAM: Initializing MMR registers
SDRAM: Calibrating PHY
SEQ.C: Preparing to start memory calibration
SEQ.C: CALIBRATION PASSED
SDRAM: 1024 MiB
SDRAM: Scrubbing 0x01000000 - 0x02000000
SDRAM: Scrubbing success with 24 ms
SDRAM: Scrubbing 0x00000000 - 0x01000000
SDRAM: Scrubbing 0x02000000 - 0x40000000
SDRAM: ECC Enabled
ALTERA DWMMC: 0

U-Boot SPL 2013.01.01 (Mar 05 2015 - 11:10:37)
BOARD : Altera SOCFPGA Cyclone V Board
SDRAM: Initializing MMR registers
SDRAM: Calibrating PHY
SEQ.C: Preparing to start memory calibration
SEQ.C: CALIBRATION PASSED
SF: Read data capture delay calibrated to 3 (0 - 6)
SF: Detected MX66L51235L with page size 65536, total: 16777216


U-Boot 2013.01.01 (Nov 28 2014 - 13:54:23)

CPU   : Altera SOCFPGA Platform
BOARD : Altera SOCFPGA Cyclone V Board
DRAM:  1 GiB
MMC:   ALTERA DWMMC: 0
SF: Read data capture delay calibrated to 3 (0 - 6)
SF: Detected MX66L51235L with page size 65536, total: 67108864
In:    serial
Out:   serial
Err:   serial
Net:   mii0
Hit any key to stop autoboot:  0
SF: Detected MX66L51235L with page size 65536, total: 67108864
altera_load: Failed with error code -4
## Starting application at 0x3FF861BC ...
## Application terminated, rc = 0xA
fpgaintf
ffd08028: 00000004    ....
fpga2sdram
ffc25080: 00000000    ....
axibridge
ffd0501c: 00000000    ....
SF: Detected MX66L51235L with page size 65536, total: 67108864
Bad Linux ARM zImage magic!

the message Bad Linux ARM zImage magic! is due to incorrect kernel image length

partition images in archive2 look ok but the flash write script

timwu@timwu-vbox:/var/lib/tftpboot/altera/archive2$ more writeall.sh
#!/bin/sh
echo "writing preloader"
flashcp preloader-mkpimage.bin  /dev/mtd0
echo "writing ubootenv"
flashcp ubootenv.dat   /dev/mtd1
echo "writing DTD"
flashcp irx3303.dtb   /dev/mtd2
echo "writing uboot"
flashcp ubootok.bin   /dev/mtd3
echo "writing kernel"
flashcp zImage /dev/mtd4
echo "writing RBF"
flashcp frsrefc5.rbf /dev/mtd5
echo "writing File system"
flashcp fsmtd6.dat /dev/mtd6
sync;sync;sync
echo "done"

it's single partitioned.

root@cyclone5:~# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 04000000 00010000 "Partition_000"

find offset options of mtdrw