-
-
Save charlesrg/425ec526a05566cceadcebe78860611d to your computer and use it in GitHub Desktop.
| #include <WiFi.h> | |
| #include <ESPmDNS.h> | |
| #include <WiFiUdp.h> | |
| #include <ArduinoOTA.h> | |
| const char* ssid = "WIFI_SSID"; | |
| const char* password = "WIFI_PASSWORD"; | |
| const char * udpAddress = "192.168.10.6"; //IP TO SEND UDP Packets with Reading. (UDP so there is no need of a connection state) | |
| const int udpPort = 44444; | |
| WiFiUDP udp; | |
| //variabls for blinking an LED with Millis | |
| const int led = 2; // ESP32 Pin to which onboard LED is connected | |
| unsigned long previousMillis = 0; // will store last time LED was updated | |
| const long interval = 1000; // interval at which to blink (milliseconds) | |
| int ledState = LOW; // ledState used to set the LED | |
| void setup() { | |
| pinMode(led, OUTPUT); | |
| Serial.begin(115200); | |
| Serial.println("Booting"); | |
| WiFi.mode(WIFI_STA); | |
| WiFi.begin(ssid, password); | |
| while (WiFi.waitForConnectResult() != WL_CONNECTED) { | |
| Serial.println("Connection Failed! Rebooting..."); | |
| delay(5000); | |
| ESP.restart(); | |
| } | |
| // Port defaults to 3232 | |
| // ArduinoOTA.setPort(3232); | |
| // Hostname defaults to esp3232-[MAC] | |
| // ArduinoOTA.setHostname("myesp32"); | |
| // No authentication by default | |
| // ArduinoOTA.setPassword("admin"); | |
| // Password can be set with it's md5 value as well | |
| // MD5(admin) = 21232f297a57a5a743894a0e4a801fc3 | |
| // ArduinoOTA.setPasswordHash("21232f297a57a5a743894a0e4a801fc3"); | |
| ArduinoOTA | |
| .onStart([]() { | |
| String type; | |
| if (ArduinoOTA.getCommand() == U_FLASH) | |
| type = "sketch"; | |
| else // U_SPIFFS | |
| type = "filesystem"; | |
| // NOTE: if updating SPIFFS this would be the place to unmount SPIFFS using SPIFFS.end() | |
| Serial.println("Start updating " + type); | |
| }) | |
| .onEnd([]() { | |
| Serial.println("\nEnd"); | |
| }) | |
| .onProgress([](unsigned int progress, unsigned int total) { | |
| Serial.printf("Progress: %u%%\r", (progress / (total / 100))); | |
| }) | |
| .onError([](ota_error_t error) { | |
| Serial.printf("Error[%u]: ", error); | |
| if (error == OTA_AUTH_ERROR) Serial.println("Auth Failed"); | |
| else if (error == OTA_BEGIN_ERROR) Serial.println("Begin Failed"); | |
| else if (error == OTA_CONNECT_ERROR) Serial.println("Connect Failed"); | |
| else if (error == OTA_RECEIVE_ERROR) Serial.println("Receive Failed"); | |
| else if (error == OTA_END_ERROR) Serial.println("End Failed"); | |
| }); | |
| ArduinoOTA.begin(); | |
| Serial.println("Ready"); | |
| Serial.print("IP address: "); | |
| Serial.println(WiFi.localIP()); | |
| udp.begin(udpPort); | |
| } | |
| void loop() { | |
| ArduinoOTA.handle(); | |
| //loop to blink without delay | |
| unsigned long currentMillis = millis(); | |
| if (currentMillis - previousMillis >= interval) { | |
| // save the last time you blinked the LED | |
| previousMillis = currentMillis; | |
| // if the LED is off turn it on and vice-versa: | |
| ledState = not(ledState); | |
| // set the LED with the ledState of the variable: | |
| digitalWrite(led, ledState); | |
| Serial.println(touchRead(T0)); // get value using T0 | |
| //data will be sent to server | |
| uint8_t buffer[50] = "Reading: \n"; | |
| char cstr[50]; | |
| sprintf_P(cstr, (PGM_P)F("T0 Level: %d, T3 Level %d.\n"),touchRead(T0),touchRead(T3)); | |
| //send hello world to server | |
| udp.beginPacket(udpAddress, udpPort); | |
| //udp.write(buffer,sizeof(buffer) ); | |
| //udp.print(touchRead(T0)); | |
| udp.print(cstr); | |
| udp.endPacket(); | |
| memset(buffer, 0, 50); | |
| } | |
| } | |
| //This code gave 23 levels without grounded strip and 29 levels grounded |
I watched your YouTube video on this. Looks like wires are just connecting from the esp32. Is that correct? Have you tried it on thicker plastic? Say like a 55 gallon drum? Have you tried using the aluminum/metal duct tape? I am very curious.
I watched your YouTube video on this. Looks like wires are just connecting from the esp32. Is that correct? Have you tried it on thicker plastic? Say like a 55 gallon drum? Have you tried using the aluminum/metal duct tape? I am very curious.
Yes, wires straight to ESP32. I tried it on a Home Depot bucket with the copper tape and it worked as well.
how did you guys get the range up to 700 on arduino ide??
Hello,
Thank you for your post. I am trying to run this code directly from my pc and not through a wireless adapter. Will it work? Also, I cant find the ESPmDNS on the library manager. Any suggestions? I however found MDNS_Generic. Is that the same by any chance?
Thank you for your time.
Edit: So I solved this problem by manually adding the ESPmDNS library from https://github.com/espressif/arduino-esp32/tree/master/libraries/ESPmDNS
Now I have this error
Arduino: 1.8.19 (Windows 7), Board: "Arduino Uno"
In file included from C:\Users*********\Desktop\sketch_dec27a\sketch_dec27a.ino:2:0:
C:\Users**********\Documents\Arduino\libraries\ESPmDNS\src/ESPmDNS.h:45:10: fatal error: IPv6Address.h: No such file or directory
#include "IPv6Address.h"^~~~~~~~~~~~~~~compilation terminated.
exit status 1
Error compiling for board Arduino Uno.
This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.Any help is appreciated.
Thank you
This might be too late for you, but I'll chime in, in case anyone else is curious: I assume you're getting the error because an arduino Uno doesn't have a wifi module onboard, whereas an esp32 does.
Hello,
Thank you for your post. I am trying to run this code directly from my pc and not through a wireless adapter. Will it work? Also, I cant find the ESPmDNS on the library manager. Any suggestions? I however found MDNS_Generic. Is that the same by any chance?
Thank you for your time.
Edit: So I solved this problem by manually adding the ESPmDNS library from https://github.com/espressif/arduino-esp32/tree/master/libraries/ESPmDNS
Now I have this error
Any help is appreciated.
Thank you