Skip to content

Instantly share code, notes, and snippets.

@cnlohr

cnlohr/sandbox_esp32_s2_frequency_and_pro_alone_gpio.c

Created July 17, 2022 11:14
Show Gist options
  • Save cnlohr/90dec0909a1f9a35a60c1c07682b9ed5 to your computer and use it in GitHub Desktop.
Save cnlohr/90dec0909a1f9a35a60c1c07682b9ed5 to your computer and use it in GitHub Desktop.
Download ZIP
ESP32-S2 Experiments with pro alone GPIO + Overclocking.
Raw
sandbox_esp32_s2_frequency_and_pro_alone_gpio.c
#include <stdio.h>
#include "esp_system.h"
#include "swadgeMode.h"
#include "hdw-led/led_util.h"
#include "hal/gpio_types.h"
#include "soc/system_reg.h"
#include "soc/dport_access.h"
#include "soc/dedic_gpio_reg.h"
#include "soc/rtc_cntl_reg.h"
#include "esp_log.h"
#include "soc/rtc.h"
#include "esp32s2/regi2c_ctrl.h"
int global_i = 100;
esp_err_t esp_flash_read(void *chip, void *buffer, uint32_t address, uint32_t length);
void local_rtc_clk_apll_enable(bool enable, uint32_t sdm0, uint32_t sdm1, uint32_t sdm2, uint32_t o_div)
{
REG_SET_FIELD(RTC_CNTL_ANA_CONF_REG, RTC_CNTL_PLLA_FORCE_PD, enable ? 0 : 1);
REG_SET_FIELD(RTC_CNTL_ANA_CONF_REG, RTC_CNTL_PLLA_FORCE_PU, enable ? 1 : 0);
if (enable) {
REGI2C_WRITE_MASK(I2C_APLL, I2C_APLL_DSDM2, sdm2);
REGI2C_WRITE_MASK(I2C_APLL, I2C_APLL_DSDM0, sdm0);
REGI2C_WRITE_MASK(I2C_APLL, I2C_APLL_DSDM1, sdm1);
REGI2C_WRITE(I2C_APLL, I2C_APLL_SDM_STOP, APLL_SDM_STOP_VAL_1);
REGI2C_WRITE(I2C_APLL, I2C_APLL_SDM_STOP, APLL_SDM_STOP_VAL_2_REV1);
REGI2C_WRITE_MASK(I2C_APLL, I2C_APLL_OR_OUTPUT_DIV, o_div);
#if 0
/* calibration */
REGI2C_WRITE(I2C_APLL, I2C_APLL_IR_CAL_DELAY, APLL_CAL_DELAY_1);
REGI2C_WRITE(I2C_APLL, I2C_APLL_IR_CAL_DELAY, APLL_CAL_DELAY_2);
REGI2C_WRITE(I2C_APLL, I2C_APLL_IR_CAL_DELAY, APLL_CAL_DELAY_3);
/* wait for calibration end */
while (!(REGI2C_READ_MASK(I2C_APLL, I2C_APLL_OR_CAL_END))) {
/* use esp_rom_delay_us so the RTC bus doesn't get flooded */
esp_rom_delay_us(1);
}
#endif
}
}
void sandbox_main(display_t * disp)
{
ESP_LOGI( "sandbox", "Running from IRAM. %d", global_i );
DPORT_SET_PERI_REG_MASK( DPORT_CPU_PERI_CLK_EN_REG, DPORT_CLK_EN_DEDICATED_GPIO );
DPORT_CLEAR_PERI_REG_MASK( DPORT_CPU_PERI_RST_EN_REG, DPORT_RST_EN_DEDICATED_GPIO);
gpio_config_t io_conf={
.mode=GPIO_MODE_OUTPUT,
.pin_bit_mask=(1ULL<<GPIO_NUM_16)
};
ESP_ERROR_CHECK(gpio_config(&io_conf));
// DPORT_REG_WRITE( GPIO_ENABLE_W1TS_REG, 1<<GPIO_NUM_16 );
DPORT_REG_WRITE( DEDIC_GPIO_OUT_CPU_REG, 0x01 ); // Enable CPU instruction output
gpio_matrix_out( GPIO_NUM_16, PRO_ALONEGPIO_OUT0_IDX, 0, 0 );
// APLL Appears to max out at sdm2=10, odiv=sdm0=sdm1=0
// You can push it higher but it doesn't actually hit 160MHz out.
//local_rtc_clk_apll_enable(1, 0 /*sdm0*/, 0 /*sdm1*/, 25 /*sdm2*/, 255 /*odiv*/);
// Set clock_source = 3, PLL = 0, CDIV = 3.
int div_ref = 0;
int div7_0 = 8;
int dr1 = 0;
int dr3 = 0;
int dchgp = 5;
int dcur = 4;
if( 0 )
{
// 480MHz
/* Clear this register to let the digital part know 480M PLL is used */
SET_PERI_REG_MASK(DPORT_CPU_PER_CONF_REG, DPORT_PLL_FREQ_SEL);
/* Configure 480M PLL */
div_ref = 0;
div7_0 = 8;
dr1 = 0;
dr3 = 0;
dchgp = 5;
dcur = 4;
REGI2C_WRITE(I2C_BBPLL, I2C_BBPLL_MODE_HF, 0x6B);
} else if( 0 )
{
// 320 MHz
CLEAR_PERI_REG_MASK(DPORT_CPU_PER_CONF_REG, DPORT_PLL_FREQ_SEL);
/* Configure 320M PLL */
div_ref = 0;
div7_0 = 4;
dr1 = 0;
dr3 = 0;
dchgp = 5;
dcur = 5;
REGI2C_WRITE(I2C_BBPLL, I2C_BBPLL_MODE_HF, 0x69);
}
else
{
CLEAR_PERI_REG_MASK(DPORT_CPU_PER_CONF_REG, DPORT_PLL_FREQ_SEL);
div_ref = 1; // 0: 80 MHz 3: 20 MHz
div7_0 = 26;
// NOTE: Uc @ 80 when @ 480M
// @ 0x6B, div7_0 = 4 = 53.333 MHz
// @ 0x6B, div7_0 = 8 = 80 MHz
// @ 0x6B, div7_0 = 10 = 92.6 MHz
// @ 0x6B, div7_0 = 11 = 100 MHz
// @ 0x6B -> Will not work at = 12
// @ 0x40, div7_0 = 8 = 40 MHz?
// @ 0x80, div7_0 = 8 = 9.3 MHz
// @ 0x30, div7_0 = 8 = 80 MHz
// @ 0x3b, div7_0 = 8 = 80 MHz
// @ 0x39, div7_0 = 8 = 80 MHz
// @ 0x19, div7_0 = 8 = 40 MHz
// @ 0x20, div7_0 = 8 = 80 MHz
// @ 0x2f, div7_0 = 8 = 80 MHz
// @ 0x69, div7_0 = 27, div_ref = 1 = 103.2 (Works full bore at 307.6MHz fCPU (FSB = 615MHz)
dr1 = 0; //No apparent impact?
dr3 = 3; //No apparent impact?
dchgp = 5; //No apparent impact?
dcur = 5; //No apparent impact?
REGI2C_WRITE(I2C_BBPLL, I2C_BBPLL_MODE_HF, 0x6e);
}
uint8_t i2c_bbpll_lref = (dchgp << I2C_BBPLL_OC_DCHGP_LSB) | (div_ref);
uint8_t i2c_bbpll_div_7_0 = div7_0;
uint8_t i2c_bbpll_dcur = (2 << I2C_BBPLL_OC_DLREF_SEL_LSB ) | (1 << I2C_BBPLL_OC_DHREF_SEL_LSB) | dcur;
REGI2C_WRITE(I2C_BBPLL, I2C_BBPLL_OC_REF_DIV, i2c_bbpll_lref);
REGI2C_WRITE(I2C_BBPLL, I2C_BBPLL_OC_DIV_7_0, i2c_bbpll_div_7_0);
REGI2C_WRITE_MASK(I2C_BBPLL, I2C_BBPLL_OC_DR1, dr1);
REGI2C_WRITE_MASK(I2C_BBPLL, I2C_BBPLL_OC_DR3, dr3);
REGI2C_WRITE(I2C_BBPLL, I2C_BBPLL_OC_DCUR, i2c_bbpll_dcur);
// SYSTEM_SOC_CLK_SEL
// 0 = XTAL
// 1 = PLL (default)
// 2 = CLK8M
// 3 = APLL_CLK
const int clock_source = 1; //SEL_0
const int SEL_1_PLL = 0; //SEL_1
const int SEL_2_CDIV = 3; //SEL_2
// If CDIV = 0, 480->80MHz
// If CDIV = 1, 480->160MHz
// If CDIV = 2, 480->240MHz
// If CDIV = 3, 480->240MHz
// "PLL" seems to have no impact.
DPORT_REG_WRITE( DPORT_CPU_PER_CONF_REG, ( DPORT_REG_READ( DPORT_CPU_PER_CONF_REG ) & 0xfffffff8 ) | (SEL_1_PLL << 2) | (SEL_2_CDIV << 0) ); // SYSTEM_PLL_FREQ_SEL, SYSTEM_CPUPERIOD_SEL
DPORT_REG_WRITE( DPORT_SYSCLK_CONF_REG, ( DPORT_REG_READ( DPORT_SYSCLK_CONF_REG ) & 0xfffff3ff ) | (clock_source << 10) );
ESP_LOGI( "sandbox", "Main Done on %d", GPIO_NUM_16 );
}
void sandbox_exit()
{
ESP_LOGI( "sandbox", "Exit" );
}
void sandbox_tick()
{
//uint32_t buffer[4] = { 0 };
//int r = esp_flash_read( 0, buffer, 0x3f0000, sizeof( buffer ) );
// ESP_LOGI( "sandbox", "global_i: %d", global_i++ );
// Create a nice little pulse train.
__asm__ __volatile__ ("set_bit_gpio_out 0x1");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("clr_bit_gpio_out 0x1");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("set_bit_gpio_out 0x1");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("clr_bit_gpio_out 0x1");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("set_bit_gpio_out 0x1");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("clr_bit_gpio_out 0x1");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("set_bit_gpio_out 0x1");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("clr_bit_gpio_out 0x1");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("set_bit_gpio_out 0x1");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("clr_bit_gpio_out 0x1");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("set_bit_gpio_out 0x1");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("clr_bit_gpio_out 0x1");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("set_bit_gpio_out 0x1");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("nop");
__asm__ __volatile__ ("clr_bit_gpio_out 0x1");
global_i++;
//ESP_LOGI( "sandbox", "At %d", global_i );
}
swadgeMode sandbox_mode =
{
.modeName = "sandbox",
.fnEnterMode = sandbox_main,
.fnExitMode = sandbox_exit,
.fnMainLoop = sandbox_tick,
.fnButtonCallback = NULL,
.fnTouchCallback = NULL,
.wifiMode = NO_WIFI,
.fnEspNowRecvCb = NULL,
.fnEspNowSendCb = NULL,
.fnAccelerometerCallback = NULL,
.fnAudioCallback = NULL,
.fnTemperatureCallback = NULL
};
@ShlomoAmar
Copy link

Hi
i get error "Compilation error: swadgeMode.h: No such file or directory"
where " swadgeMode.h" can be found?

@cnlohr
Copy link
Author

cnlohr commented Nov 9, 2022

@ShlomoAmar Right here: https://github.com/AEFeinstein/Super-2023-Swadge-FW/blob/main/main/swadgeMode.h but, this is much more for illustrative purposes. the test is from the swadge (to verify that it works) but you can just copy-paste the appropriate parts.

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment