rlamsal1256

Git Repo Health Aliases

Portable Git aliases for reading a codebase through its history before opening files.

Source

Inspired by Ally Piechowski's post:

• https://piechowski.io/post/git-commands-before-reading-code/?utm_source=tldrnewsletter

DataWhisker

Title: Senior Engineer Task Execution Rule

Applies to: All Tasks

Rule:
You are a senior engineer with deep experience building production-grade AI agents, automations, and workflow systems. Every task you execute must follow this procedure without exception:

1.Clarify Scope First
•Before writing any code, map out exactly how you will approach the task.
•Confirm your interpretation of the objective.

jefflarkin

# 
# Klipper configuration file for Anycubic i3 MEGA S
#
# This config file contains settings of all printer pins (steppers, sensors) for Anycubic i3 mega S with TMC2208 Drivers with stock plug orientation 
# Klipper firmware should be compiled for the atmega2560
#
# Config file includes
#  - Original or 2208(2209) rotated by cable drivers
#  - Mesh bed leveling: BLtouch (3DTouch sensor from Triangelab)
#  - Manual meshed bed leveling (commented out)

dhh

ruby '2.7.1'

gem 'rails', github: 'rails/rails'
gem 'tzinfo-data', '>= 1.2016.7'  # Don't rely on OSX/Linux timezone data

# Action Text
gem 'actiontext', github: 'basecamp/actiontext', ref: 'okra'
gem 'okra', github: 'basecamp/okra'

# Drivers

wosephjeber

Renaming table in Ecto migration

I recently wanted to rename a model and its postgres table in a Phoenix app. Renaming the table was simple and documented, but the table also had constraints, sequences, and indexes that needed to be updated in order for the Ecto model to be able to rely on default naming conventions. I couldn't find any examples of what this would look like but was eventually able to figure it out. For anyone else in the same situation, hopefully this example helps.

In the example below, I'm renaming the Permission model to Membership. This model belongs to a User and an Account, so it has foreign key constraints that need to be renamed.

defmodule MyApp.Repo.Migrations.RenamePermissionsToMemberships do
  use Ecto.Migration

chrismccord

If you want a run-down of the 1.3 changes and the design decisions behidn those changes, check out the LonestarElixir Phoenix 1.3 keynote: https://www.youtube.com/watch?v=tMO28ar0lW8

To use the new phx.new project generator, you can install the archive with the following command:

$ mix archive.install https://github.com/phoenixframework/archives/raw/master/phx_new.ez

Bump your phoenix dep

Phoenix v1.3.0 is a backwards compatible release with v1.2.x. To upgrade your existing 1.2.x project, simply bump your phoenix dependency in mix.exs:

jatcwang

! model
  pc101           Generic 101-key PC
  pc102           Generic 102-key (Intl) PC
  pc104           Generic 104-key PC
  pc105           Generic 105-key (Intl) PC
  dell101         Dell 101-key PC
  latitude        Dell Latitude series laptop
  dellm65         Dell Precision M65
  everex          Everex STEPnote
  flexpro         Keytronic FlexPro

bpierre

Switch To Vim For Good

NOTE: This guide has moved to https://github.com/bpierre/switch-to-vim-for-good

This guide is coming from an email I used to send to newcomers to Vim. It is not intended to be a complete guide, it is about how I switched myself.

My decision to switch to Vim has been made a long time ago. Coming from TextMate 1, I wanted to learn an editor that is Open Source (so I don’t lose my time learning a tool that can be killed), cross platform (so I can use it everywhere), and powerful enough (so I won’t regret TextMate). For these reasons, Vim has always been the editor I wanted to learn, but it took me several years before I did it in a way that works for me. I tried to switch progressively, using the Janus Vim distribution for a few months, then got back to using TextMate 2 for a time, waiting for the next attempt… here is what finally worked for me.

Original gist with comments: https://gist.github.com/bpierre/0a0025d348b6001394e0

wkf

# -*- mode: haproxy -*-
# vi: set ft=haproxy :

defaults
  log     global
  mode    http
  option  forwardfor
  option  dontlognull
  option  redispatch
  option  http-server-close

aesnyder

bind generic f !@git fetch
bind generic p !@git pull
bind generic P !@git push
bind generic { !?git push -f
bind generic r !git rebase -i master
bind generic U !@git up
bind generic M !@git checkout master
bind generic ! !@git reset HEAD^
bind generic @ !@?git reset --hard HEAD^
bind generic a !git commit --amend