danbst · January 23, 2022 12:36
diff --git a/failed_SMART.txt b/failed_SMART.txt
 [nixos@nixos:~]$ sudo smartctl -a /dev/sdb
 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.62] (local build)
 Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

 === START OF INFORMATION SECTION ===
 Model Family:     Toshiba 3.5" DT01ACA... Desktop HDD
 Device Model:     TOSHIBA DT01ACA200
 Serial Number:    84QBH18TS
 LU WWN Device Id: 5 000039 ffad3500c
 Firmware Version: MX4OABB0
 User Capacity:    2,000,398,934,016 bytes [2.00 TB]
 Sector Sizes:     512 bytes logical, 4096 bytes physical
 Rotation Rate:    7200 rpm
 Form Factor:      3.5 inches
 Device is:        In smartctl database [for details use: -P show]
 ATA Version is:   ATA8-ACS T13/1699-D revision 4
 SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
 Local Time is:    Sun Jan 23 12:29:49 2022 UTC
 SMART support is: Available - device has SMART capability.
 SMART support is: Enabled

 === START OF READ SMART DATA SECTION ===
 SMART overall-health self-assessment test result: FAILED!
 Drive failure expected in less than 24 hours. SAVE ALL DATA.
 See vendor-specific Attribute list for failed Attributes.

 General SMART Values:
 Offline data collection status:  (0x84)	Offline data collection activity
 					was suspended by an interrupting command from host.
 					Auto Offline Data Collection: Enabled.
 Self-test execution status:      (   0)	The previous self-test routine completed
 					without error or no self-test has ever 
 					been run.
 Total time to complete Offline 
 data collection: 		(14822) seconds.
 Offline data collection
 capabilities: 			 (0x5b) SMART execute Offline immediate.
 					Auto Offline data collection on/off support.
 					Suspend Offline collection upon new
 					command.
 					Offline surface scan supported.
 					Self-test supported.
 					No Conveyance Self-test supported.
 					Selective Self-test supported.
 SMART capabilities:            (0x0003)	Saves SMART data before entering
 					power-saving mode.
 					Supports SMART auto save timer.
 Error logging capability:        (0x01)	Error logging supported.
 					General Purpose Logging supported.
 Short self-test routine 
 recommended polling time: 	 (   1) minutes.
 Extended self-test routine
 recommended polling time: 	 ( 247) minutes.
 SCT capabilities: 	       (0x003d)	SCT Status supported.
 					SCT Error Recovery Control supported.
 					SCT Feature Control supported.
 					SCT Data Table supported.

 SMART Attributes Data Structure revision number: 16
 Vendor Specific SMART Attributes with Thresholds:
 ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   067   067   016    Pre-fail  Always       -       6282
  2 Throughput_Performance  0x0005   062   062   054    Pre-fail  Offline      -       2103
  3 Spin_Up_Time            0x0007   126   126   024    Pre-fail  Always       -       311 (Average 290)
  4 Start_Stop_Count        0x0012   100   100   000    Old_age   Always       -       1089
  5 Reallocated_Sector_Ct   0x0033   001   001   005    Pre-fail  Always   FAILING_NOW 943
  7 Seek_Error_Rate         0x000b   064   064   067    Pre-fail  Always   FAILING_NOW 327873
  8 Seek_Time_Performance   0x0005   001   001   020    Pre-fail  Offline  FAILING_NOW 2190
  9 Power_On_Hours          0x0012   100   100   000    Old_age   Always       -       6540
 10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       731
 192 Power-Off_Retract_Count 0x0032   097   097   000    Old_age   Always       -       4628
 193 Load_Cycle_Count        0x0012   097   097   000    Old_age   Always       -       4628
 194 Temperature_Celsius     0x0002   240   240   000    Old_age   Always       -       25 (Min/Max 14/44)
 196 Reallocated_Event_Count 0x0032   001   001   000    Old_age   Always       -       17257
 197 Current_Pending_Sector  0x0022   001   001   000    Old_age   Always       -       8784
 198 Offline_Uncorrectable   0x0008   097   097   000    Old_age   Offline      -       227
 199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       19

 SMART Error Log Version: 1
 ATA Error Count: 23288 (device log contains only the most recent five errors)
 	CR = Command Register [HEX]
 	FR = Features Register [HEX]
 	SC = Sector Count Register [HEX]
 	SN = Sector Number Register [HEX]
 	CL = Cylinder Low Register [HEX]
 	CH = Cylinder High Register [HEX]
 	DH = Device/Head Register [HEX]
 	DC = Device Command Register [HEX]
 	ER = Error register [HEX]
 	ST = Status register [HEX]
 Powered_Up_Time is measured from power on, and printed as
 DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
 SS=sec, and sss=millisec. It "wraps" after 49.710 days.

 Error 23288 occurred at disk power-on lifetime: 6540 hours (272 days + 12 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 08 08 00 00  Error: UNC at LBA = 0x00000808 = 2056

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 08 f8 00 0a 80 40 08      00:00:54.319  READ FPDMA QUEUED
  60 08 b8 80 08 c0 40 08      00:00:54.318  READ FPDMA QUEUED
  60 08 b0 00 09 80 40 08      00:00:54.318  READ FPDMA QUEUED
  60 08 a8 40 08 c0 40 08      00:00:54.318  READ FPDMA QUEUED
  60 08 a0 80 08 80 40 08      00:00:54.310  READ FPDMA QUEUED

 Error 23287 occurred at disk power-on lifetime: 6540 hours (272 days + 12 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 08 08 00 00  Error: UNC at LBA = 0x00000808 = 2056

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 08 90 20 08 c0 40 08      00:00:50.385  READ FPDMA QUEUED
  60 08 88 20 08 80 40 08      00:00:50.385  READ FPDMA QUEUED
  60 08 80 08 08 00 40 08      00:00:50.384  READ FPDMA QUEUED
  60 08 78 f8 06 80 40 08      00:00:50.384  READ FPDMA QUEUED
  60 08 70 a8 87 e0 40 08      00:00:50.384  READ FPDMA QUEUED

 Error 23286 occurred at disk power-on lifetime: 6540 hours (272 days + 12 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 f8 08 08 00 00  Error: UNC at LBA = 0x00000808 = 2056

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 b0 00 08 80 40 08      00:00:36.327  READ FPDMA QUEUED
  60 00 a8 00 08 c0 40 08      00:00:36.327  READ FPDMA QUEUED
  60 00 a0 00 08 00 40 08      00:00:36.327  READ FPDMA QUEUED
  60 00 98 00 00 00 40 08      00:00:36.327  READ FPDMA QUEUED
  60 08 10 00 00 00 40 08      00:00:36.271  READ FPDMA QUEUED

 Error 23285 occurred at disk power-on lifetime: 6540 hours (272 days + 12 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 08 08 00 00  Error: UNC at LBA = 0x00000808 = 2056

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 08 48 00 0a c0 40 08      00:00:32.266  READ FPDMA QUEUED
  60 08 40 00 09 c0 40 08      00:00:32.265  READ FPDMA QUEUED
  60 08 00 00 0c 80 40 08      00:00:32.257  READ FPDMA QUEUED
  60 08 f8 00 0a 80 40 08      00:00:32.256  READ FPDMA QUEUED
  60 08 10 08 08 00 40 08      00:00:32.239  READ FPDMA QUEUED

 Error 23284 occurred at disk power-on lifetime: 6540 hours (272 days + 12 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 08 08 00 00  Error: UNC at LBA = 0x00000808 = 2056

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 08 e0 00 09 80 40 08      00:00:28.357  READ FPDMA QUEUED
  60 08 38 80 08 c0 40 08      00:00:28.357  READ FPDMA QUEUED
  60 08 d8 80 08 80 40 08      00:00:28.356  READ FPDMA QUEUED
  60 08 30 40 08 c0 40 08      00:00:28.356  READ FPDMA QUEUED
  60 08 d0 40 08 80 40 08      00:00:28.356  READ FPDMA QUEUED

 SMART Self-test log structure revision number 1
 Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
 # 1  Short offline       Completed: read failure       50%      6252         3408

 SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
 Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
 If Selective self-test is pending on power-up, resume after 0 minute delay.
	[nixos@nixos:~]$ sudo smartctl -a /dev/sdb
	smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.62] (local build)
	Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

	=== START OF INFORMATION SECTION ===
	Model Family: Toshiba 3.5" DT01ACA... Desktop HDD
	Device Model: TOSHIBA DT01ACA200
	Serial Number: 84QBH18TS
	LU WWN Device Id: 5 000039 ffad3500c
	Firmware Version: MX4OABB0
	User Capacity: 2,000,398,934,016 bytes [2.00 TB]
	Sector Sizes: 512 bytes logical, 4096 bytes physical
	Rotation Rate: 7200 rpm
	Form Factor: 3.5 inches
	Device is: In smartctl database [for details use: -P show]
	ATA Version is: ATA8-ACS T13/1699-D revision 4
	SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
	Local Time is: Sun Jan 23 12:29:49 2022 UTC
	SMART support is: Available - device has SMART capability.
	SMART support is: Enabled

	=== START OF READ SMART DATA SECTION ===
	SMART overall-health self-assessment test result: FAILED!
	Drive failure expected in less than 24 hours. SAVE ALL DATA.
	See vendor-specific Attribute list for failed Attributes.

	General SMART Values:
	Offline data collection status: (0x84) Offline data collection activity
	was suspended by an interrupting command from host.
	Auto Offline Data Collection: Enabled.
	Self-test execution status: ( 0) The previous self-test routine completed
	without error or no self-test has ever
	been run.
	Total time to complete Offline
	data collection: (14822) seconds.
	Offline data collection
	capabilities: (0x5b) SMART execute Offline immediate.
	Auto Offline data collection on/off support.
	Suspend Offline collection upon new
	command.
	Offline surface scan supported.
	Self-test supported.
	No Conveyance Self-test supported.
	Selective Self-test supported.
	SMART capabilities: (0x0003) Saves SMART data before entering
	power-saving mode.
	Supports SMART auto save timer.
	Error logging capability: (0x01) Error logging supported.
	General Purpose Logging supported.
	Short self-test routine
	recommended polling time: ( 1) minutes.
	Extended self-test routine
	recommended polling time: ( 247) minutes.
	SCT capabilities: (0x003d) SCT Status supported.
	SCT Error Recovery Control supported.
	SCT Feature Control supported.
	SCT Data Table supported.

	SMART Attributes Data Structure revision number: 16
	Vendor Specific SMART Attributes with Thresholds:
	ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
	1 Raw_Read_Error_Rate 0x000b 067 067 016 Pre-fail Always - 6282
	2 Throughput_Performance 0x0005 062 062 054 Pre-fail Offline - 2103
	3 Spin_Up_Time 0x0007 126 126 024 Pre-fail Always - 311 (Average 290)
	4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 1089
	5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 943
	7 Seek_Error_Rate 0x000b 064 064 067 Pre-fail Always FAILING_NOW 327873
	8 Seek_Time_Performance 0x0005 001 001 020 Pre-fail Offline FAILING_NOW 2190
	9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 6540
	10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
	12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 731
	192 Power-Off_Retract_Count 0x0032 097 097 000 Old_age Always - 4628
	193 Load_Cycle_Count 0x0012 097 097 000 Old_age Always - 4628
	194 Temperature_Celsius 0x0002 240 240 000 Old_age Always - 25 (Min/Max 14/44)
	196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 17257
	197 Current_Pending_Sector 0x0022 001 001 000 Old_age Always - 8784
	198 Offline_Uncorrectable 0x0008 097 097 000 Old_age Offline - 227
	199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 19

	SMART Error Log Version: 1
	ATA Error Count: 23288 (device log contains only the most recent five errors)
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
	Powered_Up_Time is measured from power on, and printed as
	DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
	SS=sec, and sss=millisec. It "wraps" after 49.710 days.

	Error 23288 occurred at disk power-on lifetime: 6540 hours (272 days + 12 hours)
	When the command that caused the error occurred, the device was active or idle.

	After command completion occurred, registers were:
	ER ST SC SN CL CH DH
	-- -- -- -- -- -- --
	40 51 08 08 08 00 00 Error: UNC at LBA = 0x00000808 = 2056

	Commands leading to the command that caused the error were:
	CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
	-- -- -- -- -- -- -- -- ---------------- --------------------
	60 08 f8 00 0a 80 40 08 00:00:54.319 READ FPDMA QUEUED
	60 08 b8 80 08 c0 40 08 00:00:54.318 READ FPDMA QUEUED
	60 08 b0 00 09 80 40 08 00:00:54.318 READ FPDMA QUEUED
	60 08 a8 40 08 c0 40 08 00:00:54.318 READ FPDMA QUEUED
	60 08 a0 80 08 80 40 08 00:00:54.310 READ FPDMA QUEUED

	Error 23287 occurred at disk power-on lifetime: 6540 hours (272 days + 12 hours)
	When the command that caused the error occurred, the device was active or idle.

	After command completion occurred, registers were:
	ER ST SC SN CL CH DH
	-- -- -- -- -- -- --
	40 51 08 08 08 00 00 Error: UNC at LBA = 0x00000808 = 2056

	Commands leading to the command that caused the error were:
	CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
	-- -- -- -- -- -- -- -- ---------------- --------------------
	60 08 90 20 08 c0 40 08 00:00:50.385 READ FPDMA QUEUED
	60 08 88 20 08 80 40 08 00:00:50.385 READ FPDMA QUEUED
	60 08 80 08 08 00 40 08 00:00:50.384 READ FPDMA QUEUED
	60 08 78 f8 06 80 40 08 00:00:50.384 READ FPDMA QUEUED
	60 08 70 a8 87 e0 40 08 00:00:50.384 READ FPDMA QUEUED

	Error 23286 occurred at disk power-on lifetime: 6540 hours (272 days + 12 hours)
	When the command that caused the error occurred, the device was active or idle.

	After command completion occurred, registers were:
	ER ST SC SN CL CH DH
	-- -- -- -- -- -- --
	40 51 f8 08 08 00 00 Error: UNC at LBA = 0x00000808 = 2056

	Commands leading to the command that caused the error were:
	CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
	-- -- -- -- -- -- -- -- ---------------- --------------------
	60 00 b0 00 08 80 40 08 00:00:36.327 READ FPDMA QUEUED
	60 00 a8 00 08 c0 40 08 00:00:36.327 READ FPDMA QUEUED
	60 00 a0 00 08 00 40 08 00:00:36.327 READ FPDMA QUEUED
	60 00 98 00 00 00 40 08 00:00:36.327 READ FPDMA QUEUED
	60 08 10 00 00 00 40 08 00:00:36.271 READ FPDMA QUEUED

	Error 23285 occurred at disk power-on lifetime: 6540 hours (272 days + 12 hours)
	When the command that caused the error occurred, the device was active or idle.

	After command completion occurred, registers were:
	ER ST SC SN CL CH DH
	-- -- -- -- -- -- --
	40 51 08 08 08 00 00 Error: UNC at LBA = 0x00000808 = 2056

	Commands leading to the command that caused the error were:
	CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
	-- -- -- -- -- -- -- -- ---------------- --------------------
	60 08 48 00 0a c0 40 08 00:00:32.266 READ FPDMA QUEUED
	60 08 40 00 09 c0 40 08 00:00:32.265 READ FPDMA QUEUED
	60 08 00 00 0c 80 40 08 00:00:32.257 READ FPDMA QUEUED
	60 08 f8 00 0a 80 40 08 00:00:32.256 READ FPDMA QUEUED
	60 08 10 08 08 00 40 08 00:00:32.239 READ FPDMA QUEUED

	Error 23284 occurred at disk power-on lifetime: 6540 hours (272 days + 12 hours)
	When the command that caused the error occurred, the device was active or idle.

	After command completion occurred, registers were:
	ER ST SC SN CL CH DH
	-- -- -- -- -- -- --
	40 51 08 08 08 00 00 Error: UNC at LBA = 0x00000808 = 2056

	Commands leading to the command that caused the error were:
	CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
	-- -- -- -- -- -- -- -- ---------------- --------------------
	60 08 e0 00 09 80 40 08 00:00:28.357 READ FPDMA QUEUED
	60 08 38 80 08 c0 40 08 00:00:28.357 READ FPDMA QUEUED
	60 08 d8 80 08 80 40 08 00:00:28.356 READ FPDMA QUEUED
	60 08 30 40 08 c0 40 08 00:00:28.356 READ FPDMA QUEUED
	60 08 d0 40 08 80 40 08 00:00:28.356 READ FPDMA QUEUED

	SMART Self-test log structure revision number 1
	Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
	# 1 Short offline Completed: read failure 50% 6252 3408

	SMART Selective self-test log data structure revision number 1
	SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
	1 0 0 Not_testing
	2 0 0 Not_testing
	3 0 0 Not_testing
	4 0 0 Not_testing
	5 0 0 Not_testing
	Selective self-test flags (0x0):
	After scanning selected spans, do NOT read-scan remainder of disk.
	If Selective self-test is pending on power-up, resume after 0 minute delay.