gistfile1.txt

[0000.126] Processing in cold boot mode Bootloader 2
[0000.131] A02 Bootrom Patch rev = 63
[0000.134] Power-up reason: reset button
[0000.138] No Battery Present
[0000.140] RamCode = 0
[0000.143] Platform has Ddr4 type ram
[0000.146] max77620 disabling SD1 Remote Sense
[0000.150] Setting Ddr voltage to 1125mv
[0000.154] Serial Number of Pmic Max77663: 0x2712ae
[0000.162] Entering ramdump check
[0000.165] Get RamDumpCarveOut = 0x0
[0000.168] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.173] Last reboot was clean, booting normally!
[0000.178] Sdram initialization is successful 
[0000.182] SecureOs Carveout Base=0xff800000 Size=0x00800000
[0000.187] GSC1 Carveout Base=0xff700000 Size=0x00100000
[0000.192] GSC2 Carveout Base=0xff600000 Size=0x00100000
[0000.198] GSC3 Carveout Base=0xff500000 Size=0x00100000
[0000.203] GSC4 Carveout Base=0xff400000 Size=0x00100000
[0000.208] GSC5 Carveout Base=0xff300000 Size=0x00100000
[0000.213] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000
[0000.218] Lp0 Carveout Base=0xff2bf000 Size=0x00001000
[0000.234] RamDump Carveout Base=0xff23f000 Size=0x00080000
[0000.239] Platform-DebugCarveout: 0
[0000.242] Nck Carveout Base=0xff03f000 Size=0x00200000
[0000.247] Non secure mode. Disable rollback prevention
[0000.252] AOTAG Init Done
[0000.280] Using GPT Primary to query partitions 
[0000.285] Loading Tboot-CPU binary
[0000.334] Verifying bootloader in OdmNonSecureSBK mode
[0000.344] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.351] Bootloader downloaded successfully.
[0000.355] Downloaded Tboot-CPU binary to 0xa0000258
[0000.360] MAX77620_GPIO1 Configured.
[0000.364] MAX77620_GPIO5 Configured.
[0000.367] CPU power rail is up
[0000.370] CPU clock enabled
[0000.374] Performing RAM repair
[0000.377] Updating A64 Warmreset Address to 0xa00002e9
[0000.394] Bootloader DTB Load Address: 0x83000000
[0000.410] Kernel DTB Load Address: 0x83080000
[0000.415] Loading cboot binary
[0000.509] Verifying bootloader in OdmNonSecureSBK mode
[0000.611] Bootloader load address is 0x8010fda8, entry address is 0x80110000
[0000.618] Bootloader downloaded successfully.
[0000.623] GPT: Partition NOT found ! 
[0000.626] Find Partition via GPT Failed
[0000.630] Find Partition via PT Failed
[0000.633] function NvTbootGetBinaryOffsets: 0x1 error
[0000.638] Error in NvTbootLoadBinary: 0x1 !
[0000.642] Next binary entry address: 0x80110000 
[0000.646] BoardId: 2180
[0000.672] NvTbootI2cProbe(): error code 0x00045100 Error while read
[0000.678] Display board id is not available 
[0000.683] dram memory type is 3
[0000.687] WB0 init successful
[0000.713] Bpmp FW successfully loaded
[0000.716] Set NvDecSticky Bits
[0000.719] GSC1 address : ff700000
[0000.723] GSC2 address ff63fffc value c0edbbcc
[0000.728] GSC2 address : ff600000
[0000.731] GSC3 address : ff500000
[0000.735] GSC4 address : ff400000
[0000.739] GSC5 address : ff300000
[0000.742] GSC MC Settings done
[0000.746] TOS old plaintext Image length 65536
[0000.752] *** Secure OS image signature not verified ***
[0000.757] Loading and Validation of Secure OS Successful
[0000.762] NvTbootPackSdramParams: start. 
[0000.767] NvTbootPackSdramParams: done. 
[0000.771] Tegraboot started after 99053 us
[0000.775] Basic modules init took 292257 us
[0000.779] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB
[0000.784] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB
[0000.792] Next stage binary read took 12211 us
[0000.796] Carveout took 261164 us
[0000.799] CPU initialization took 125102 us
[0000.803] Total time taken by TegraBoot 690734 us

[0000.808] Starting CPU & Halting co-processor 

64b[0000.915] RamCode = 0
[0000.930] LPDDR4 Training: Read DT: Number of tables = 10
[0000.935] EMC Training (SRC-freq: 204000; DST-freq: 40800)
[0000.941] EMC Training Skipped
[0000.943] EMC Training (SRC-freq: 204000; DST-freq: 68000)
[0000.949] EMC Training Skipped
[0000.951] EMC Training (SRC-freq: 204000; DST-freq: 102000)
[0000.957] EMC Training Skipped
[0000.959] EMC Training (SRC-freq: 204000; DST-freq: 204000)
[0000.965] EMC Training Skipped
[0000.967] EMC Training (SRC-freq: 204000; DST-freq: 408000)
[0000.974] EMC Training Successful
[0000.977] EMC Training (SRC-freq: 204000; DST-freq: 665600)
[0000.983] EMC Training Successful
[0000.986] EMC Training (SRC-freq: 204000; DST-freq: 800000)
[0000.997] EMC Training Successful
[0001.000] EMC Training (SRC-freq: 204000; DST-freq: 1065600)
[0001.023] EMC Training Successful
[0001.026] EMC Training (SRC-freq: 204000; DST-freq: 1331200)
[0001.047] EMC Training Successful
[0001.050] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.070] EMC Training Successful
[0001.073] Switching to 800000 KHz Success
[0001.079] DT Write: emc-table@40800 succeeded
[0001.086] DT Write: emc-table@68000 succeeded
[0001.092] DT Write: emc-table@102000 succeeded
[0001.098] DT Write: emc-table@204000 succeeded
[0001.105] DT Write: emc-table@408000 succeeded
[0001.111] DT Write: emc-table@665600 succeeded
[0001.118] DT Write: emc-table@800000 succeeded
[0001.124] DT Write: emc-table@1065600 succeeded
[0001.130] DT Write: emc-table@1331200 succeeded
[0001.137] DT Write: emc-table@1600000 succeeded
[0001.141] LPDDR4 Training: Write DT: Number of tables = 10


U-Boot 2016.11+dfsg1-4 (Mar 27 2017 - 18:39:51 +0000)

TEGRA210
Model: NVIDIA P2371-2180
Board: NVIDIA P2371-2180
DRAM:  3.5 GiB
MMC:   Tegra SD/MMC: 0, Tegra SD/MMC: 1
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
reading /extlinux/extlinux.conf
730 bytes read in 15 ms (46.9 KiB/s)
------------------------------------------------------------
1:      NixOS - Default
Enter choice: 1:        NixOS - Default
Retrieving file: /extlinux/../nixos/dl5p9bgh5qszbqdi98v21wkbhxl6klcx-initrd-initrd
reading /extlinux/../nixos/dl5p9bgh5qszbqdi98v21wkbhxl6klcx-initrd-initrd
4015121 bytes read in 208 ms (18.4 MiB/s)
Retrieving file: /extlinux/../nixos/wn1w38bpd3pflskaiff22mjakh1qb7rj-linux-4.10.1-Image
reading /extlinux/../nixos/wn1w38bpd3pflskaiff22mjakh1qb7rj-linux-4.10.1-Image
23982592 bytes read in 1091 ms (21 MiB/s)
append: systemConfig=/nix/store/rxsmwpxj4b26kl78v0n82b0244mr26qa-nixos-system-nixos-17.09pre-git init=/nix/store/rxsmwpxj4b26kl78v0n82b0244mr26qa-nixos-system-nixos-17.09pre-git/init loglevel=7 console=ttyS0,115200n8 console=tty0
Retrieving file: /extlinux/../nixos/wn1w38bpd3pflskaiff22mjakh1qb7rj-linux-4.10.1-dtbs/tegra210-p2371-2180.dtb
reading /extlinux/../nixos/wn1w38bpd3pflskaiff22mjakh1qb7rj-linux-4.10.1-dtbs/tegra210-p2371-2180.dtb
** Unable to read file /extlinux/../nixos/wn1w38bpd3pflskaiff22mjakh1qb7rj-linux-4.10.1-dtbs/tegra210-p2371-2180.dtb **
Skipping nixos-default for failure retrieving fdt
SCRIPT FAILED: continuing...
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
977 bytes read in 76 ms (11.7 KiB/s)
p2371-2180 eMMC boot options
1:      primary kernel
Enter choice: