KoboGloOKReaderBoot.txt

U-Boot 2009.08 (May 01 2016 - 19:06:52)

CPU:   Freescale i.MX50 family 1.1V at 800 MHz
mx50 pll1: 800MHz
mx50 pll2: 400MHz
mx50 pll3: 216MHz
ipg clock     : 66666666Hz
ipg per clock : 66666666Hz
uart clock    : 24000000Hz
ahb clock     : 133333333Hz
axi_a clock   : 400000000Hz
axi_b clock   : 200000000Hz
weim_clock    : 100000000Hz
ddr clock     : 200000000Hz
esdhc1 clock  : 80000000Hz
esdhc2 clock  : 80000000Hz
esdhc3 clock  : 80000000Hz
esdhc4 clock  : 80000000Hz
Board: MX50 RDP board
Boot Reason: [POR]
Boot Device: SD
I2C:   ready
DRAM:  256 MB
MMC:   FSL_ESDHC: 0, FSL_ESDHC: 1, FSL_ESDHC: 2
*** Warning - bad CRC or MMC, using default environment

In:    serial
Out:   serial
Err:   serial
[_get_sd_number] g_sd_number:0

MMC read: dev # 0, block # 1023, count 1 partition # 0 ...
1 blocks read: OK

MMC read: dev # 0, block # 1024, count 1 partition # 0 ...
1 blocks read: OK
turning on FL
ram p=70000000,size=268435456

MMC read: dev # 0, block # 18431, count 1 partition # 0 ...
1 blocks read: OK

MMC read: dev # 0, block # 18432, count 759 partition # 0 ...
759 blocks read: OK

MMC read: dev # 0, block # 14335, count 1 partition # 0 ...
1 blocks read: OK

MMC read: dev # 0, block # 14336, count 2228 partition # 0 ...
2228 blocks read: OK
Kernel RAM visiable size=254M->254M
init TPS65185 power ...
Hit any key to stop autoboot:  0

MMC read: dev # 0, block # 2047, count 1 partition # 0 ...
1 blocks read: OK
kernel size = 3347004

MMC read: dev # 0, block # 2048, count 6543 partition # 0 ...
6543 blocks read: OK

MMC read: dev # 0, block # 1, count 1 partition # 0 ...
1 blocks read: OK
hwcfg rootfstype : 2
hwcfg partition type : 7
## Booting kernel from Legacy Image at 70800000 ...
   Image Name:   r?_#1 May 1 19:21:07
   Created:      2016-05-01  18:21:24 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1912748 Bytes =  1.8 MB
   Load Address: 70008000
   Entry Point:  70008000
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.35.3-850-gbc67621+ (cosmin@orangepi) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sun May 1 19:21:07 BST 2016
CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7d
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: Freescale MX50 Reference Design Platform
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64516
Kernel command line: console=ttymxc0,115200 rootwait rw no_console_suspend lpj=3997696 hwcfg_p=0x7ffffe00 hwcfg_sz=110 logo_p=0x7ffa1000 logo_sz=388096 waveform_p=0x7fe8a800 waveform_sz=1140399 mem=254M boot_port=0 androidboot.serialno=20030394,b3f7fdff960a45bebbc97f7e0266bf42 rootfstype=ext4 root=/dev/mmcblk0p1
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 254MB = 254MB total
Memory: 253944k/253944k available, 6152k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xf9e00000 - 0xffe00000   (  96 MB)
    vmalloc : 0x90000000 - 0xf4000000   (1600 MB)
    lowmem  : 0x80000000 - 0x8fe00000   ( 254 MB)
    pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
    modules : 0x7f000000 - 0x7fe00000   (  14 MB)
      .init : 0x80008000 - 0x80024000   ( 112 kB)
      .text : 0x80024000 - 0x8035e000   (3304 kB)
      .data : 0x80376000 - 0x803b02c0   ( 233 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
        RCU-based detection of stalled CPUs is disabled.
        Verbose stalled-CPUs detection is disabled.
NR_IRQS:368
MXC GPIO hardware
MXC IRQ initialized
MXC_Early serial console at MMIO 0x53fc0000 (options '115200')
bootconsole [ttymxc0] enabled
Console: colour dummy device 80x30
Calibrating delay loop (skipped) preset value.. 799.53 BogoMIPS (lpj=3997696)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
i.MX IRAM pool: 128 KB@0x90040000
hwcfg_size_setup() hwcfg_szie=110
hwcfg_p_setup() hwcfg_p=7ffffe00,vaddr=9006ee00,size=110
hwcfg_p_setup() pcba="E606E0" !!
root_path_setup() rootdev=0,rootpart=1
boot_port_setup() boot_port=0
CPU is i.MX50 Revision 1.1
[check_hardware_name-580] PCBA ID is 30
Using SDMA I.API
MXC DMA API initialized
IMX usb wakeup probe
IMX usb wakeup probe
bio: create slab <bio-0> at 0
regulator: DCDC_3V15: 3150 mV
SCSI subsystem initialized
CSPI: mxc_spi-2 probed
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
mc13892 Rev 0.0 FinVer 0 detected
Initializing regulators for mx50 rdp.
regulator: SW1: 600 <--> 1375 mV at 600 mV
Device spi3.0 probed
Switching to clocksource mxc_timer1
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
LPMode driver module loaded
Static Power Management for Freescale i.MX5
PM driver module loaded
sdram autogating driver module loaded
Bus freq driver module loaded
tle4913_init : HallSensor not exist !
ESD/ISD DSM
mxc_dvfs_core_probe
DVFS driver module loaded
i.MXC CPU frequency driver
DVFS PER driver module loaded
msgmni has been set to 495
alg: No test for stdrng (krng)
cryptodev: driver loaded.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
drivers/video/mxc/mxc_epdc_fb.c(5630):EPD 1024x758
waveform_size_setup() wf_size=1140399
waveform_p_setup() wf_p=7fe8a800,vaddr=90200800,size=1140399
logo_size_setup() logo_szie=388096
logo_p_setup() logo_p=7ffa1000,vaddr=90100000,size=388096
Console: switching to colour frame buffer device 128x47
[epdc_firmware_func]:fw p=90200800,size=1140399
drivers/video/mxc/mxc_epdc_fb.c(5083):EPD 1024x758
fake_s1d13522_parse_epd_cmdline : epd cmdline parse already done .
client0@i2c2 ,addr=0x68,name=tps65185-1
TPS65185 versions : major=0x1,minor=0x2,version=0x5,RevID=0x65
Serial: MXC Internal UART driver
mxcintuart.0: ttymxc0 at MMIO 0x53fc0000 (irq = 32) is a Freescale i.MX
console [ttymxc0] enabled, bootconsole disabled
console [ttymxc0] enabled, bootconsole disabled
mxcintuart.1: ttymxc1 at MMIO 0x53fbc000 (irq = 31) is a Freescale i.MX
mxcintuart.2: ttymxc2 at MMIO 0x5000c000 (irq = 33) is a Freescale i.MX
loop: module loaded
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[arch/arm/plat-mxc/usb_common.c-343] usbh1_set_utmi_xcvr()
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.1: irq 14, io base 0x53f80200
fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
input: mxckpd as /devices/platform/mxckpd/input/input0
MXC keypad loaded
input: zForce-ir-touch as /devices/virtual/input/input1
add mma7660 i2c driver
mc13892 rtc probe start
[zForce_ir_touch_recv_data-206] command BootComplete (0)...
pmic_rtc pmic_rtc.1: rtc core: registered pmic_rtc as rtc0
mc13892 rtc probe succeed
i2c /dev entries driver
APM Battery Driver
MXC WatchDog Driver 2.0
[msp430_probe-588] MSP430 firmware version C851
[drivers/mxc/pmic/mc13892/pmic_battery.c-1003] pmic_battery_probe...
[ntx_get_battery_vol-1843] 60,bat=954
[ntx_get_battery_vol-1843] 60,bat=954
mxsdhci: MXC Secure Digital Host Controller Interface driver
mxsdhci: MXC SDHCI Controller Driver.
mmc0: SDHCI detect irq 0 irq 1 INTERNAL DMA
mxsdhci: MXC SDHCI Controller Driver.
mmc1: SDHCI detect irq 273 irq 2 INTERNAL DMA
mxsdhci: MXC SDHCI Controller Driver.
mmc2: SDHCI detect irq 0 irq 3 INTERNAL DMA
TCP cubic registered
NET: Registered protocol family 17
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
pmic_rtc pmic_rtc.1: setting system clock to 2018-04-20 03:06:41 UTC (1524193601)
[zForce_ir_touch_recv_data-223] firmware version 0000 0000 0000 0000
[ntx_get_battery_vol-1843] 60,bat=954
[ntx_get_battery_vol-1843] 60,bat=954
Waiting for root device /dev/mmcblk0p1...
mmc0: new high speed SDHC card at address aaaa
mmcblk0: mmc0:aaaa SS16G 14.8 GiB
 mmcblk0: p1 p3
EXT4-fs (mmcblk0p1): 1 truncate cleaned up
EXT4-fs (mmcblk0p1): recovery complete
EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 179:1.
Freeing init memory: 112K
[k_wait_update_complete]waitupdate ret=-22,4294937462->4294937462
TPS65185 temprature data = 0x19,25
[PROGRESS_BAR-2917] No progess ...
ARC USBOTG Device Controller driver (1 August 2005)
g_file_storage gadget-lun0: unable to open backing file: /dev/mmcblk0p3
usb unplugged