Repair "ubuntu--vg-root" not found with LUKS and LVM encryption

.crypt-fix.md

Crypt-fix

Use this script via curl -L -O https://gist.github.com/dragon788/e777ba64d373210e4f6306ad40ee0e80/raw/a86f3d05fb56feb6ef01fc2d61a4feb2fd82b281/crypt-fix.sh and sudo bash ./crypt-fix.sh. You may need to edit the DEVICE variable to reflect your disk and partition layout (this was created on an EFI system using LUKS and LVM). It will prompt you for your disk password once to mount and discover the correct name for the encrypted volume mount and then prompt again to mount with the correct name so that the update-initramfs command succeeds with the appropriate mapping, if this wasn't done you would get a warning and your next boot would still fail.

crypt-fix.sh

#!/bin/bash
# Call with `sudo bash DEBUG=1 ./crypt-fix.sh` for verbose output
[ -n "$DEBUG"] && set -x
# Prompt user for device from /dev/sd* /dev/nvme* /dev/mmc* prefixes?
# For /dev/sda probably sda1 is EFI and sda2 is boot and sda3 is encrypted
DEVICE=/dev/nvme0n1
EFIPATH="${DEVICE}p1"
BOOTPATH="${DEVICE}p2"
CRYPTPATH="${DEVICE}p3"
TARGETPATH=/mnt
# Need root for mounting stuff
if ! (( $EUID == 0 )); then echo "Please run with `sudo $0`"; fi

clear_mounts () {
# Clears mounts in case of interrupt or upon exit to allow running script multiple times
umount $TARGETPATH/boot/efi
umount $TARGETPATH/boot
umount $TARGETPATH/proc
umount $TARGETPATH/dev
umount $TARGETPATH
vgchange -an
cryptsetup close temp_name
cryptsetup close $CRYPTNAME
set +x
}
trap clear_mounts INT EXIT

cryptsetup open $CRYPTPATH temp_name
vgchange -ay
# Can't get this until LVM devices are scanned above
ROOTPATH=$(ls /dev/mapper/* | grep root)
# Make sure nothing else is mounted on our $TARGETPATH
umount $TARGETPATH
wait
mount $ROOTPATH $TARGETPATH
# Find the name that is required for `update-initramfs` to properly update things
CRYPTNAME=$(cat $TARGETPATH/etc/crypttab | awk '/^[ ]*[^#]/ { print $1; exit }')
umount $TARGETPATH
vgchange -an
cryptsetup close temp_name
# This proper name is required for `update-initramfs` to properly update things
cryptsetup open $CRYPTPATH $CRYPTNAME
wait
vgchange -ay
ROOTPATH=$(ls /dev/mapper/* | grep root)
mount $ROOTPATH $TARGETPATH
mount $BOOTPATH $TARGETPATH/boot
mount $EFIPATH $TARGETPATH/boot/efi
mount -t proc proc $TARGETPATH/proc
mount -o bind /dev $TARGETPATH/dev
# Have also seen people mounting dev/pts and run and sys, they don't appear to be necessary

chroot $TARGETPATH update-initramfs -c -k all
echo "Completed crypt-fix, try rebooting and you should get prompted for your passphrase after grub"

references.md

https://feeding.cloud.geek.nz/posts/recovering-from-unbootable-ubuntu-encrypted-lvm-root-partition/ https://superuser.com/a/111215/333828 https://help.ubuntu.com/community/ManualFullSystemEncryption/Troubleshooting

Thanks for this, it helped me figure out a solution to my problem. After an update my computer booted right into a broken GRUB console which was missing commands (e.g. ls didn't work).

I was following the Manual Full System Encryption guide when installing Ubuntu. As mentioned in the Troubleshooting chapter, there is a script refreshgrub which fixed my problem. I created a separate script which helps you run refreshgrub without diving into too many details. Maybe it will help others with the same issue - https://gist.github.com/lovromazgon/7d0a5b6ac8f7557059a8b97e8442720b.

I need to come back and revisit this as using the /dev/nvme* path instead of a uuid causes issues if you ever move it between systems where it might end up on a different port/path.

Thanks so much, this saved my laptop in a critical phase after an erroneous fwupd!
However, just running the script did not work for me and gave some errors, e.g., I had ROOTPATH= being empty.
It helped to run these steps manually.
I think one could solve my issues by adding sleep 5 after every call to vgchange, but this is just a wild guess.
Thanks again!

Thanks for the notes zawlazaw. I haven't run into the issues that required running this in a while but it might help someone else if they are seeing the same errors.

I still get "dev/mapper/ubuntu--vg-root does not exist" after successfully running this Script via a live USB Stick. Any additional advice? I edited the device to match my setup: sda , 1 ,2, 3.

Add
mount -o bind /sys $TARGETPATH/sys

My drives are backwards. So I had to modify the script for my main device. This is twice it's happened after an update.

I still get "dev/mapper/ubuntu--vg-root does not exist" after successfully running this Script via a live USB Stick. Any additional advice? I edited the device to match my setup: sda , 1 ,2, 3.

I know its an old problem, but had same issue just now. Script run successfully but it was still not seeing the dev/mapper/ubuntu--vg-root.
It can be that you are missing the packages: lvm2, cryptsetup-initramfs
In my case I was missing cryptsetup-initramfs package. Installing it was tricky because inside chroot I had problems with internet connection, so instead of playing with /etc/resolve.conf to get the internet working i downloaded the package inside live-cd linux, then copied it to a mounted filesystem, and with chroot installed it via dpkg(added these commands temporary to the script). If package was missing the initramfs should update automatically but I recommend running entire script again to update it for all kernel packages.

Also note that wget in current .crypt-fix.md points to outdated revision of the gist, make sure you are using the newest one to avoid issues(I learned that the hard way)