Very small qemu-ifup script

make-bridge-for-libvirt.sh

#!/bin/bash
# make-bridge-for-libvirt.sh
#
# This scripts follows blindly the instructions from:
# http://wiki.libvirt.org/page/Networking#Fedora.2FRHEL_Bridging
#
# It tries to copy the existing physical network config
# to the bridge. It may not work if you have a non-trivial
# network setup on ifcfg-eth0.
#
# ----------------------------------------
#
# Copyright (c) 2010 Eduardo Habkost <[email protected]>
#
# Permission is hereby granted, free of charge, to any person obtaining a copy
# of this software and associated documentation files (the "Software"), to deal
# in the Software without restriction, including without limitation the rights
# to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
# copies of the Software, and to permit persons to whom the Software is
# furnished to do so, subject to the following conditions:
# 
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
# 
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
# AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
# LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
# OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
# THE SOFTWARE.
# 

must_not_exist()
{
	if [ -e "$1" ];then
		echo "A $1 file already exists" >&2
		exit 1
	fi
}

iface="$1"
bridge="$2"

if [ -z "$iface" -o -z "$bridge" ];then
	echo "Usage: make-bridge-for-libvirt.sh ethX brX" >&2
	exit 1
fi

cd /etc/sysconfig/network-scripts/
if [ ! -r "ifcfg-$iface" ];then
	echo "No ifcfg-$iface?" >&2
	exit 1
fi
orig="orig.ifcfg-$iface"
must_not_exist "$orig"
bcfg="ifcfg-$bridge"
must_not_exist "$bcfg"

echo "Disabling NetworkManager..."
chkconfig NetworkManager off
echo "Enabling network service..."
chkconfig network on

echo "Stopping NetworkManager..."
service NetworkManager stop

echo "Starting network service..."
service network start


echo "Copying eth0 network configuration to bridge..."
mv ifcfg-$iface $orig
cp $orig $bcfg

sed -i -e '/DEVICE=.*$/d' $bcfg
sed -i -e '/TYPE=.*/d' $bcfg
sed -i -e '/HWADDR=.*/d' $bcfg
echo "DEVICE=$bridge" >> $bcfg
echo "TYPE=Bridge" >> $bcfg
echo "NM_CONTROLLED=no" >> "$bcfg"
echo "ONBOOT=yes" >> "$bcfg"
echo "DELAY=0" >> "$bcfg"

echo "Creating eth0 configuration for br0..."

HWADDR=
source "./$orig"
export HWADDR
(
echo "DEVICE=$iface"
echo "HWADDR=$HWADDR"
echo "ONBOOT=yes"
echo "BRIDGE=$bridge"
echo "NM_CONTROLLED=no"
) > "ifcfg-$iface"

echo "done."
echo "Now, cross your fingers and run:"
echo "  service network restart"
echo "Good luck!"

qemu-ifup

#!/bin/bash
# A br0 bridge should be already set up.
# Compare with:
# http://en.wikibooks.org/wiki/QEMU/Networking#qemu-ifup
#
# For the bridge setup, see:
# http://wiki.libvirt.org/page/Networking#Fedora.2FRHEL_Bridging
# http://gist.github.com/393525
ip link set "$1" up
brctl addif br0 "$1"