elliotboney · September 5, 2017 19:02 · Queton · Mar 31, 2019
diff --git a/pins_ANET_10.h b/pins_ANET_10.h
 /**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */

 /**
 * Anet V1.0 board pin assignments
 */

 /**
 * Rev B    16 JUN 2017
 *
 * 1) no longer uses Sanguino files to define some of the pins
 * 2) added pointers to useable Arduino IDE extensions
 *
 */

 /**
 * The standard Arduino IDE extension (board manager) for this board
 * is located at https://github.com/SkyNet3D/anet-board.
 *
 * Installation instructions are on that page.
 *
 * After copying the files to the appropriate location, restart Arduino and
 * you'll see "Anet V1.0" and "Anet V1.0 (Optiboot)" in the boards list.
 *
 * "Anet V1.0" uses the bootloader that was installed on the board when
 * it shipped from the factory.
 *
 * "Anet V1.0 (Optiboot)" frees up another 3K of FLASH.  You'll need to burn
 * a new bootloader to the board to be able to automatically download a
 * compiled image.
 *
 */

 /**
 * Another usable Arduino IDE extension (board manager) can be found at
 * https://github.com/Lauszus/Sanguino
 *
 * This extension has been tested on Arduino 1.6.12 & 1.8.0
 *
 * Here's the JSON path:
 * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
 *
 * When installing select 1.0.2
 *
 * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
 * Just use the above JSON URL instead of Sparkfun's JSON.
 *
 * Once installed select the Sanguino board and then select the CPU.
 *
 */

 /**
 *  To burn a new bootloader:
 *
 *   1. Connect your programmer to the board.
 *   2. In the Arduino IDE select the board and then select the programmer.
 *   3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message.
 *   4. The programmer is no longer needed. Remove it.
 */

 /**
 * Additional info:
 *
 *   Anet Schematics                    - https://github.com/ralf-e/ANET-3D-Board-V1.0
 *   Wiring RRDFG Smart Controller      - http://www.thingiverse.com/thing:2103748
 *   SkyNet3D Anet software development - https://github.com/SkyNet3D/Marlin/
 *   Anet Users / Skynet SW on Facebook - https://www.facebook.com/skynet3ddevelopment/
 *
 *   Many thanks to Hans Raaf (@oderwat) for developing the Anet-specific software and supporting the Anet community.
 */

 #if !defined(__AVR_ATmega1284P__)
  #error "Oops!  Make sure you have 'Anet V1.0', 'Anet V1.0 (Optiboot)' or 'Sanguino' selected from the 'Tools -> Boards' menu."
 #endif

 #ifndef BOARD_NAME
  #define BOARD_NAME "Anet"
 #endif

 #define LARGE_FLASH true

 //
 // Limit Switches
 //
 #define X_STOP_PIN         18
 #define Y_STOP_PIN         19
 #define Z_STOP_PIN         20

 //
 // Steppers
 //
 #define X_STEP_PIN         15
 #define X_DIR_PIN          21
 #define X_ENABLE_PIN       14

 #define Y_STEP_PIN         22
 #define Y_DIR_PIN          23
 #define Y_ENABLE_PIN       14

 #define Z_STEP_PIN          3
 #define Z_DIR_PIN           2
 #define Z_ENABLE_PIN       26

 #define E0_STEP_PIN         1
 #define E0_DIR_PIN          0
 #define E0_ENABLE_PIN      14

 //
 // Temperature Sensors
 //
 #define TEMP_0_PIN          7  // Analog Input (pin 33 extruder)
 #define TEMP_BED_PIN        6  // Analog Input (pin 34 bed)

 //
 // Heaters / Fans
 //
 #define HEATER_0_PIN       13  // (extruder)
 #define HEATER_BED_PIN     12  // (bed)
 #define FAN_PIN             4

 //
 // Misc. Functions
 //
 #define SDSS               31
 #define LED_PIN            -1

 /**
 * LCD / Controller
 *
 * Only the following displays are supported:
 *  ANET_KEYPAD_LCD
 *  ANET_FULL_GRAPHICS_LCD
 *  REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
 */

 #if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
  #define LCD_SDSS           28
  #if ENABLED(ADC_KEYPAD)
    #define SERVO0_PIN         27 // free for BLTouch/3D-Touch
    #define LCD_PINS_RS        28
    #define LCD_PINS_ENABLE    29
    #define LCD_PINS_D4        10
    #define LCD_PINS_D5        11
    #define LCD_PINS_D6        16
    #define LCD_PINS_D7        17
    #define BTN_EN1            -1
    #define BTN_EN2            -1
    #define BTN_ENC            -1
    #define ADC_KEYPAD_PIN      1
    #define ENCODER_FEEDRATE_DEADZONE 2
  #elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) || ENABLED(ANET_FULL_GRAPHICS_LCD)
    // Pin definitions for the Anet A6 Full Graphics display and the RepRapDiscount Full Graphics
    // display using an adapter board  // https://go.aisler.net/benlye/anet-lcd-adapter/pcb
    // See below for alternative pin definitions for use with https://www.thingiverse.com/thing:2103748
    #define SERVO0_PIN         27 // free for BLTouch/3D-Touch
    #define BEEPER_PIN         28
    #define LCD_PINS_RS        30
    #define LCD_PINS_ENABLE    29
    #define LCD_PINS_D4        17
    #define BTN_EN1            11
    #define BTN_EN2            10
    #define BTN_ENC            16
    #define ST7920_DELAY_1 DELAY_0_NOP
    #define ST7920_DELAY_2 DELAY_1_NOP
    #define ST7920_DELAY_3 DELAY_2_NOP
    #ifndef ENCODER_STEPS_PER_MENU_ITEM
      #define ENCODER_STEPS_PER_MENU_ITEM 1
    #endif
    #ifndef ENCODER_PULSES_PER_STEP
      #define ENCODER_PULSES_PER_STEP 4
    #endif
  #endif
 #endif  // ULTRA_LCD && NEWPANEL

 /**
 * ====================================================================
 * =============== Alternative RepRapDiscount Wiring ==================
 * ====================================================================
 *
 * An alternative wiring scheme for the RepRapDiscount Full Graphics Display is
 * published by oderwat on Thingiverse at https://www.thingiverse.com/thing:2103748.
 *
 * Using that adapter requires changing the pin definition as follows:
 *   #define SERVO0_PIN        27 // free for BLTouch/3D-Touch
 *   #define BEEPER_PIN        28
 *   #define LCD_PINS_RS       30
 *   #define LCD_PINS_ENABLE   29
 *   #define LCD_PINS_D4       17
 *
 * The BLTouch pin becomes LCD:3
 */

 /**
 * ====================================================================
 * ===================== LCD PINOUTS ==================================
 * ====================================================================
 *
 *   Anet V1.0 controller           | ANET_KEYPAD_LCD   | ANET_FULL_      | RepRapDiscount Full      | Thingiverse RepRap wiring
 *   physical   logical   alt       |                   | GRAPHICS_LCD    | Graphics Display Wiring  | http://www.thingiverse
 *     pin        pin     functions |                   |                 |                          | .com/thing:2103748
 *------------------------------------------------------------------------------------------------------------------------
 *   ANET-J3.1    8 ***             | N/A               | J3_TX ***       |                          |
 *   ANET-J3.2    9 ***             | N/A               | J3_RX ***       |                          |
 *   ANET-J3.3    6       MISO      | N/A               | MISO ***        | EXP2.1   MISO            | EXP2.1   MISO
 *   ANET-J3.4    +5V               | N/A               | +5V             |                          |
 *   ANET-J3.5    7       SCK       | N/A               | SCK ***         | EXP2.2   SCK             | EXP2.2   SCK
 *   ANET-J3.6    5       MOSI      | N/A               | MOSI ***        | EXP2.6   MOSI            | EXP2.6   MOSI
 *   ANET-J3.7    !RESET            | N/A               | button          | EXP2.8   panel button    | EXP2.8   panel button
 *   ANET-J3.8    GND               | N/A               | GND             | EXP2.9   GND             | EXP2.9   GND
 *   ANET-J3.9    4       Don't use | N/A               | N/C             |                          |
 *   ANET-J3.10   +3.3V             | N/A               | +3.3V ***       |                          |
 *                                  |                   |                 |                          |
 *                                  |                   |                 |                          |
 *   ANET-LCD.1   GND               | GND               | GND             | EXP1.9   GND             | EXP1.9   GND
 *   ANET-LCD.2   +5V               | +5V               | +5V             | EXP1.10  +5V             | EXP1.10  +5V
 *   ANET-LCD.3   27      A4        | N/C *             | LCD_PINS_RS     | EXP1.4   LCD_PINS_RS     | EXP2.4   SDSS or N/C *
 *   ANET-LCD.4   10                | LCD_PINS_D4       | BTN_EN2         | EXP2.3   BTN_EN2         | EXP2.3   BTN_EN2
 *   ANET-LCD.5   28      A3        | LCD_PINS_RS       | LCD_PINS_ENABLE | EXP1.3   LCD_PINS_ENABLE | EXP1.1   BEEPER_PIN
 *   ANET-LCD.6   11                | LCD_PINS_D5       | BTN_EN1         | EXP2.5   BTN_EN1         | EXP2.5   BTN_EN1
 *   ANET-LCD.7   29      A2        | LCD_PINS_ENABLE   | N/C *           | EXP2.4   SDSS or N/C *   | EXP1.3   LCD_PINS_ENABLE
 *   ANET-LCD.8   16      SCL       | LCD_PINS_D6       | BTN_ENC         | EXP1.2   BTN_ENC         | EXP1.2   BTN_ENC
 *   ANET-LCD.9   30      A1        | ADC_KEYPAD_PIN ** | LCD_PINS_D4     | EXP1.5   LCD_PINS_D4     | EXP1.4   LCD_PINS_RS
 *   ANET-LCD.10  17      SDA       | LCD_PINS_D7       | BEEPER_PIN      | EXP1.1   BEEPER_PIN      | EXP1.5   LCD_PINS_D4
 *
 *                 N/C * - if not connected to the LCD can be used for BLTouch servo input
 *                 ** - analog pin -WITHOUT a pullup
 *                 *** - only connected to something if the Bluetooth module is populated
 */

 /**
 *   REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
 *   physical pin  function
 *   EXP1.1        BEEPER
 *   EXP1.2        BTN_ENC
 *   EXP1.3        LCD_PINS_ENABLE
 *   EXP1.4        LCD_PINS_RS
 *   EXP1.5        LCD_PINS_D4
 *   EXP1.6        LCD_PINS_D5 (not used)
 *   EXP1.7        LCD_PINS_D6 (not used)
 *   EXP1.8        LCD_PINS_D7 (not used)
 *   EXP1.9        GND
 *   EXP1.10       VCC
 *
 *
 *   EXP2.1        MISO
 *   EXP2.2        SCK
 *   EXP2.3        BTN_EN2
 *   EXP2.4        SDSS
 *   EXP2.5        BTN_EN1
 *   EXP2.6        MOSI
 *   EXP2.7        SD_DETECT_PIN
 *   EXP2.8        button
 *   EXP2.9        GND
 *   EXP2.10       NC
 */
	/**
	* Marlin 3D Printer Firmware
	* Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
	*
	* Based on Sprinter and grbl.
	* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
	*
	* This program is free software: you can redistribute it and/or modify
	* it under the terms of the GNU General Public License as published by
	* the Free Software Foundation, either version 3 of the License, or
	* (at your option) any later version.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*
	* You should have received a copy of the GNU General Public License
	* along with this program. If not, see <http://www.gnu.org/licenses/>.
	*
	*/

	/**
	* Anet V1.0 board pin assignments
	*/

	/**
	* Rev B 16 JUN 2017
	*
	* 1) no longer uses Sanguino files to define some of the pins
	* 2) added pointers to useable Arduino IDE extensions
	*
	*/

	/**
	* The standard Arduino IDE extension (board manager) for this board
	* is located at https://github.com/SkyNet3D/anet-board.
	*
	* Installation instructions are on that page.
	*
	* After copying the files to the appropriate location, restart Arduino and
	* you'll see "Anet V1.0" and "Anet V1.0 (Optiboot)" in the boards list.
	*
	* "Anet V1.0" uses the bootloader that was installed on the board when
	* it shipped from the factory.
	*
	* "Anet V1.0 (Optiboot)" frees up another 3K of FLASH. You'll need to burn
	* a new bootloader to the board to be able to automatically download a
	* compiled image.
	*
	*/

	/**
	* Another usable Arduino IDE extension (board manager) can be found at
	* https://github.com/Lauszus/Sanguino
	*
	* This extension has been tested on Arduino 1.6.12 & 1.8.0
	*
	* Here's the JSON path:
	* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
	*
	* When installing select 1.0.2
	*
	* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
	* Just use the above JSON URL instead of Sparkfun's JSON.
	*
	* Once installed select the Sanguino board and then select the CPU.
	*
	*/

	/**
	* To burn a new bootloader:
	*
	* 1. Connect your programmer to the board.
	* 2. In the Arduino IDE select the board and then select the programmer.
	* 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message.
	* 4. The programmer is no longer needed. Remove it.
	*/

	/**
	* Additional info:
	*
	* Anet Schematics - https://github.com/ralf-e/ANET-3D-Board-V1.0
	* Wiring RRDFG Smart Controller - http://www.thingiverse.com/thing:2103748
	* SkyNet3D Anet software development - https://github.com/SkyNet3D/Marlin/
	* Anet Users / Skynet SW on Facebook - https://www.facebook.com/skynet3ddevelopment/
	*
	* Many thanks to Hans Raaf (@oderwat) for developing the Anet-specific software and supporting the Anet community.
	*/

	#if !defined(__AVR_ATmega1284P__)
	#error "Oops! Make sure you have 'Anet V1.0', 'Anet V1.0 (Optiboot)' or 'Sanguino' selected from the 'Tools -> Boards' menu."
	#endif

	#ifndef BOARD_NAME
	#define BOARD_NAME "Anet"
	#endif

	#define LARGE_FLASH true

	//
	// Limit Switches
	//
	#define X_STOP_PIN 18
	#define Y_STOP_PIN 19
	#define Z_STOP_PIN 20

	//
	// Steppers
	//
	#define X_STEP_PIN 15
	#define X_DIR_PIN 21
	#define X_ENABLE_PIN 14

	#define Y_STEP_PIN 22
	#define Y_DIR_PIN 23
	#define Y_ENABLE_PIN 14

	#define Z_STEP_PIN 3
	#define Z_DIR_PIN 2
	#define Z_ENABLE_PIN 26

	#define E0_STEP_PIN 1
	#define E0_DIR_PIN 0
	#define E0_ENABLE_PIN 14

	//
	// Temperature Sensors
	//
	#define TEMP_0_PIN 7 // Analog Input (pin 33 extruder)
	#define TEMP_BED_PIN 6 // Analog Input (pin 34 bed)

	//
	// Heaters / Fans
	//
	#define HEATER_0_PIN 13 // (extruder)
	#define HEATER_BED_PIN 12 // (bed)
	#define FAN_PIN 4

	//
	// Misc. Functions
	//
	#define SDSS 31
	#define LED_PIN -1

	/**
	* LCD / Controller
	*
	* Only the following displays are supported:
	* ANET_KEYPAD_LCD
	* ANET_FULL_GRAPHICS_LCD
	* REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
	*/

	#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
	#define LCD_SDSS 28
	#if ENABLED(ADC_KEYPAD)
	#define SERVO0_PIN 27 // free for BLTouch/3D-Touch
	#define LCD_PINS_RS 28
	#define LCD_PINS_ENABLE 29
	#define LCD_PINS_D4 10
	#define LCD_PINS_D5 11
	#define LCD_PINS_D6 16
	#define LCD_PINS_D7 17
	#define BTN_EN1 -1
	#define BTN_EN2 -1
	#define BTN_ENC -1
	#define ADC_KEYPAD_PIN 1
	#define ENCODER_FEEDRATE_DEADZONE 2
	#elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) \|\| ENABLED(ANET_FULL_GRAPHICS_LCD)
	// Pin definitions for the Anet A6 Full Graphics display and the RepRapDiscount Full Graphics
	// display using an adapter board // https://go.aisler.net/benlye/anet-lcd-adapter/pcb
	// See below for alternative pin definitions for use with https://www.thingiverse.com/thing:2103748
	#define SERVO0_PIN 27 // free for BLTouch/3D-Touch
	#define BEEPER_PIN 28
	#define LCD_PINS_RS 30
	#define LCD_PINS_ENABLE 29
	#define LCD_PINS_D4 17
	#define BTN_EN1 11
	#define BTN_EN2 10
	#define BTN_ENC 16
	#define ST7920_DELAY_1 DELAY_0_NOP
	#define ST7920_DELAY_2 DELAY_1_NOP
	#define ST7920_DELAY_3 DELAY_2_NOP
	#ifndef ENCODER_STEPS_PER_MENU_ITEM
	#define ENCODER_STEPS_PER_MENU_ITEM 1
	#endif
	#ifndef ENCODER_PULSES_PER_STEP
	#define ENCODER_PULSES_PER_STEP 4
	#endif
	#endif
	#endif // ULTRA_LCD && NEWPANEL

	/**
	* ====================================================================
	* =============== Alternative RepRapDiscount Wiring ==================
	* ====================================================================
	*
	* An alternative wiring scheme for the RepRapDiscount Full Graphics Display is
	* published by oderwat on Thingiverse at https://www.thingiverse.com/thing:2103748.
	*
	* Using that adapter requires changing the pin definition as follows:
	* #define SERVO0_PIN 27 // free for BLTouch/3D-Touch
	* #define BEEPER_PIN 28
	* #define LCD_PINS_RS 30
	* #define LCD_PINS_ENABLE 29
	* #define LCD_PINS_D4 17
	*
	* The BLTouch pin becomes LCD:3
	*/

	/**
	* ====================================================================
	* ===================== LCD PINOUTS ==================================
	* ====================================================================
	*
	* Anet V1.0 controller \| ANET_KEYPAD_LCD \| ANET_FULL_ \| RepRapDiscount Full \| Thingiverse RepRap wiring
	* physical logical alt \| \| GRAPHICS_LCD \| Graphics Display Wiring \| http://www.thingiverse
	* pin pin functions \| \| \| \| .com/thing:2103748
	*------------------------------------------------------------------------------------------------------------------------
	* ANET-J3.1 8 * \| N/A \| J3_TX * \| \|
	* ANET-J3.2 9 * \| N/A \| J3_RX * \| \|
	* ANET-J3.3 6 MISO \| N/A \| MISO *** \| EXP2.1 MISO \| EXP2.1 MISO
	* ANET-J3.4 +5V \| N/A \| +5V \| \|
	* ANET-J3.5 7 SCK \| N/A \| SCK *** \| EXP2.2 SCK \| EXP2.2 SCK
	* ANET-J3.6 5 MOSI \| N/A \| MOSI *** \| EXP2.6 MOSI \| EXP2.6 MOSI
	* ANET-J3.7 !RESET \| N/A \| button \| EXP2.8 panel button \| EXP2.8 panel button
	* ANET-J3.8 GND \| N/A \| GND \| EXP2.9 GND \| EXP2.9 GND
	* ANET-J3.9 4 Don't use \| N/A \| N/C \| \|
	* ANET-J3.10 +3.3V \| N/A \| +3.3V *** \| \|
	* \| \| \| \|
	* \| \| \| \|
	* ANET-LCD.1 GND \| GND \| GND \| EXP1.9 GND \| EXP1.9 GND
	* ANET-LCD.2 +5V \| +5V \| +5V \| EXP1.10 +5V \| EXP1.10 +5V
	* ANET-LCD.3 27 A4 \| N/C * \| LCD_PINS_RS \| EXP1.4 LCD_PINS_RS \| EXP2.4 SDSS or N/C *
	* ANET-LCD.4 10 \| LCD_PINS_D4 \| BTN_EN2 \| EXP2.3 BTN_EN2 \| EXP2.3 BTN_EN2
	* ANET-LCD.5 28 A3 \| LCD_PINS_RS \| LCD_PINS_ENABLE \| EXP1.3 LCD_PINS_ENABLE \| EXP1.1 BEEPER_PIN
	* ANET-LCD.6 11 \| LCD_PINS_D5 \| BTN_EN1 \| EXP2.5 BTN_EN1 \| EXP2.5 BTN_EN1
	* ANET-LCD.7 29 A2 \| LCD_PINS_ENABLE \| N/C * \| EXP2.4 SDSS or N/C * \| EXP1.3 LCD_PINS_ENABLE
	* ANET-LCD.8 16 SCL \| LCD_PINS_D6 \| BTN_ENC \| EXP1.2 BTN_ENC \| EXP1.2 BTN_ENC
	* ANET-LCD.9 30 A1 \| ADC_KEYPAD_PIN ** \| LCD_PINS_D4 \| EXP1.5 LCD_PINS_D4 \| EXP1.4 LCD_PINS_RS
	* ANET-LCD.10 17 SDA \| LCD_PINS_D7 \| BEEPER_PIN \| EXP1.1 BEEPER_PIN \| EXP1.5 LCD_PINS_D4
	*
	* N/C * - if not connected to the LCD can be used for BLTouch servo input
	* ** - analog pin -WITHOUT a pullup
	* *** - only connected to something if the Bluetooth module is populated
	*/

	/**
	* REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
	* physical pin function
	* EXP1.1 BEEPER
	* EXP1.2 BTN_ENC
	* EXP1.3 LCD_PINS_ENABLE
	* EXP1.4 LCD_PINS_RS
	* EXP1.5 LCD_PINS_D4
	* EXP1.6 LCD_PINS_D5 (not used)
	* EXP1.7 LCD_PINS_D6 (not used)
	* EXP1.8 LCD_PINS_D7 (not used)
	* EXP1.9 GND
	* EXP1.10 VCC
	*
	*
	* EXP2.1 MISO
	* EXP2.2 SCK
	* EXP2.3 BTN_EN2
	* EXP2.4 SDSS
	* EXP2.5 BTN_EN1
	* EXP2.6 MOSI
	* EXP2.7 SD_DETECT_PIN
	* EXP2.8 button
	* EXP2.9 GND
	* EXP2.10 NC
	*/