uyjulian

How to install Homebrew package manager on Steam Deck

(See also installing Distroboxm, which is included in SteamOS 3.5 and newer: https://distrobox.it/ )
(See also installing Nix package manager: https://determinate.systems/posts/nix-on-the-steam-deck )

You can install Homebrew (a package manager for macOS and Linux) without disabling the read-only partition with sudo steamos-readonly disable.
The package manager can be used alongside Flatpaks. Some software is only available on Flathub, and some software is only available on Homebrew.

1. Switch to desktop mode (hold power button until a menu appears, then select "Switch to desktop mode")
2. Click the logo at the bottom left, go to System, then go to Konsole

Jiab77

Create DNS-over-TLS bridge with Pi-hole, unbound and stubby on Ubuntu Server

Few months ago, I've made a similar work but I wanted something a little more easier to manage. Please have a look at here for my previous work.

This time, I'm gonna do pretty much the same thing but using Pi-hole as base then modify it to include unbound and stubby.

This way, I can use the power of Pi-hole with some additional security layers:

• Recursive DNS check (unbound)
• DNS-over-TLS (stubby)

mikestecker

optimising-unifi-performance

NOTE: Content below is written by Adrian Mace. Click here for an updated version.

Below are the key settings that I apply on any unifi installation for optimal performance.

Settings

Settings > Site

• Ensure Enable Advanced Features is enabled
  This allows you to follow along with the guide in it's entirety.

jasonehines

Routing between two UniFi USG based LANs with ZeroTier

Intro

This is a quick explanation of how to configure both ZeroTier and two Ubiquiti UniFi USGs to allow routing between two IPv4 networks. Both networks are in private (RFC1918) address space and each one has its own DHCP service. There is no need for NAT between them, only IP routing.

The two networks are 192.168.1.0/24 (call this the "left" network) and 192.168.10.0/24 (the "right" network) but they can be anything. Also, you can have multiple CIDR blocks on one side or the other of the ZeroTier route; if you do, you just have to create more routing table entries.

markofu

Security Tools for AWS

I often get asked which tools are good to use for securing your AWS infrastructure so I figured I'd write a short listof some useful Security Tools for the AWS Cloud Infrastructure.

This list is not intended be something completely exhaustive, more so provide a good launching pad for someone as they dig into AWS and want to make it secure from the start.

Open Source

This section focuses on tools and services provided by the community and released as open-source.

rickcrawford

Create 2 files: main.go and docker-compose.yml. Once both are created use docker-compose up and it will build the necessary files and start Elastic Search.

I found it necessary to add elastic.SetSniff(false) or I could not connect. Also remember the docker containers have security enabled for Elasticsearch with the password set as elastic:changeme. You can test it using curl:

curl http://127.0.0.1:9200/_cat/health -u elastic:changeme

Once it is running you can successfully run the main.go file using go run main.go.

aabs

Creating a useful cloud migration model

This is a transformation of Adrian Colyer's Checklist to turn it into a working model for a cloud transformation. The assumption is that the original checklist can suffice for any services that are deployed on the build pipeline, but the question to answer here is about how the environment is provisioned, deployed, monitored and governed in such a way as to fit the architecture implicit in the service checklist.

Configuration and Secret Management

• Config is supplied via environment variables.
• Anything that doesn't vary between deploys should not be externalised.
• Deployment orchestrator should supply config as it deploys a service
• Secrets should never be supplied as config
• Desired deployment state should be declaratively described in code in a VCS.

gene1wood

[
  {
    "Document": {
      "Statement": [
        {
          "Action": [
            "directconnect:Describe*",
            "ec2:DescribeVpnGateways"
          ],
          "Effect": "Allow",

diegopacheco

AWS Setup

1. Create AWS role called Spinnaker with proper access.
2. run aws configure and set your keys/secret.

Install Git and NVM

sudo apt-get -y install git
git clone https://github.com/spinnaker/spinnaker.git

maffblaster

$ cat mkefiboot
#!/bin/bash

macbootimg() {
        python /usr/lib/python3.3/site-packages/livedvd/mkefiboot -a -l "Gentoo Linux" -i gentoo.icns -p "Gentoo Linux" efi/boot macboot.img
}

efiimg() {
        local mountdir
        mountdir=$(mktemp -d)