Install OpenWrt on TP-Link TL-MR6400 V4

install-openwrt-on-tp-link-tl-mr6400-v4.md

Install OpenWrt on TP-Link TL-MR6400 V4

1. Download OpenWrt firmware image here.

2. Flash your router using this guide.

3. SSH into your router: ssh [email protected].

4. Add a new interface in /etc/config/network.

  	option device 'switch0'
 	option vlan '2'
 	option ports '4 6t'
+
+config interface 'vodafone'
+	option proto 'modemmanager'
+	option device '/sys/devices/platform/101c0000.ehci/usb1/1-1'
+	option apn 'internet'
+	option pincode '0000'
+	option username 'web'
+	option password 'web'

5. Get the path of your device from mmcli -m 0. Do not use /dev/cdc-wdm0.

6. Add the newly added interface in /etc/config/firewall.

 config zone
 	option name		wan
 	list   network		'wan'
 	list   network		'wan6'
+	list   network		'vodafone'
 	option input		REJECT
 	option output		ACCEPT
 	option forward		REJECT

7. Reboot your router: reboot.

8. Enjoy!

@flauzff This image does not include LuCi. If you have any error, then better build the image yourself specifying the LuCi package.

Tnx for the answer. I will try to do it, until then I need to reimstall original stock fw. Hope all works fine

Hello! I've recently installed your firmware on my router, because I wasn't able to set the stable image to use the QMI modem. It works great, thank you! I noticed also that there are no builds after v20210613 are any new versions planned or maybe an image that is based on the stable image? I'm asking because I wanted to install the openvpn package, but opkg says that the kernel is too old to satisfy the requirements. I haven't tried on the stable version, because I have no network connection to download the package. The error is the following:

Collected errors:
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for openvpn-openssl:
 * 	kernel (= 5.4.134-1-5e0d078e8605d0579be4caafdf2317c8)
 * opkg_install_cmd: Cannot install package openvpn-openssl.

Hello @capsia37, sorry for the long delay. Have you found a solution? Did you try an older release?

are any new versions planned
@capsia37

Yes, the pipeline was on hold because of no activity on the repository the last 60 days.

Hello @capsia37, sorry for the long delay. Have you found a solution? Did you try an older release?

Yes, I've tried the previous versions, but I couldn't install the package because the kernel version is 5.4.124 instead of the required 5.4.134. I don't know why the package wants exactly that version, maybe it can be recompiled to work with 5.4.124.

Yes, I've tried the previous versions, but I couldn't install the package because the kernel version is 5.4.124 instead of the required 5.4.134. I don't know why the package wants exactly that version, maybe it can be recompiled to work with 5.4.124.

A new version has been released, try it out. It should have a kernel version >= 5.4.134.

A new version has been released, try it out. It should have a kernel version >= 5.4.134.

Thank you! Now it doesn't show errors, but there is not enough space to install the package

It seems strange to me as it is marked as a 8/64 device, but only 5.6MB are shown in the partitions above using df -h. When I installed it with the official 21.02 image it showed 2.4MB free in Luci. How can I check if there is unused space?

The best option is to build the image with all the packages you want instead of installing them to save some space. If I am not mistaken, the result of the df command you showed seems to be correct.

The best option is to build the image with all the packages you want instead of installing them to save some space. If I am not mistaken, the result of the df command you showed seems to be correct.

Thanks for all the help! I'll try to build an image with the packages.

What might be the password for ssh on factory firmware?

I tried this on TP-Link TL-MR6400 V5 but had no success, because of insufficient drive space to install the package "modemmanager".

So here are my steps using QMI and the simple LuCI configuration interface.

Hi, can you help me to add 2 packages iptables-mod-ipopt & kmod-ipt-ipopt to openwrt firmware? Your firmware builds very well but I can't install the above 2 packages, it's not compatible
Thank you very much!

Hi I am using this MR6400 openwrt firmware on my MR400 router. But the wifi chip can only work under 300Mbps rate, the only difference between MR6400 and MR400 is that MR400 has a AC1200 Mbps wifi chip. So how can I patch a driver module or build a firmware that supports AC1200 wifi chip? Or someone know how to do that then help me?