How to install TrueNAS SCALE on a partition instead of the full disk

Install FreeNAS SCALE on a partition and create a mirror.md

Install TrueNAS SCALE on a partition instead of the full disk

The TrueNAS installer doesn't have a way to use anything less than the full device. This is usually a waste of resources when installing to a modern NVMe which is usually several hundred of GB. TrueNAS SCALE will use only a few GB for its system files so installing to a 16GB partition would be helpful.

The easiest way to solve this is to modify the installer script before starting the installation process.

1. Boot TrueNAS Scale installer from USB stick/ISO

2. Select shell in the first menu (instead of installing)

3. While in the shell, run the following commands:

   sed -i 's/sgdisk -n3:0:0/sgdisk -n3:0:+16384M/g' /usr/sbin/truenas-install
   /usr/sbin/truenas-install
   

   For TrueNAS Scale 24.10+ see this comment.

   The first command modifies the installer script so that it creates a 16GiB boot-pool partition instead of using the full disk. The second command restarts the TrueNAS Scale installer.

4. Continue installing according to the official docs.

Step 7-12 in the deprecated guide has instructions on how to allocate the remaining space to a partition you can use for data. If you are using a single drive just ignore the steps that has to do with mirroring.

Deprecated guide using a USB stick as intermediary

Unfortunately this is only possible by using an intermediate device to act as the installation disk and later move this data to the NVMe. Below I have documented the steps I took to get TrueNAS SCALE to run from a mirrored 16GB partition on NVMe disks.

For an easier initial partition please see this comment and the discussion that follows. Should remove the need to use a USB stick as a intermediate medium.

1. Install TrueNAS SCALE on a USB drive, preferrably 16GB in size. If you use a 32GB stick you must create a 32GB partition on the NVMe, wasting space that can be used for VMs and Docker/k8s applications.

2. Boot and enter a Linux shell as root. For example by enabling SSH service and login by root password.

3. Check available devices

    $ parted
    (parted) print devices
    /dev/sdb (15.4GB)  # boot device
    /dev/nvme0n1 (500GB)
    /dev/nvme1n1 (512GB)
    (parted) quit
   

If you only have one NVMe disk just ignore the instructions that include the second disk (nvme1n1). This disk is used to create a ZFS mirror to handle disk failures.

4. Clone the boot device to the other devices

    $ cat /dev/sdb > /dev/nvme0n1
    $ cat /dev/sdb > /dev/nvme1n1
   

5. Check the partition layout. Fix all the GPT space warning prompts that show up.

    $ parted -l
    [...]
    Warning: Not all of the space available to /dev/nvme0n1 appears to be used, you can fix the GPT to use all of the
    space (an extra 946741296 blocks) or continue with the current setting?
    Fix/Ignore? f
    [...]
    Model:  USB  SanDisk 3.2Gen1 (scsi)
    Disk /dev/sdb: 15.4GB
    Sector size (logical/physical): 512B/512B
    Partition Table: gpt
    Disk Flags:
   
    Number  Start   End     Size    File system  Name  Flags
     1      20.5kB  1069kB  1049kB                     bios_grub
     2      1069kB  538MB   537MB   fat32              boot, esp
     3      538MB   15.4GB  14.8GB  zfs
    [...]
   

   The other disks partition table should look identical to this.

6. Remove the zfs partition from the new devices, number 3 in this case. This is the boot-pool partition and we will recreate it later. The reason we remove it is that zfs will recognize metadata that makes it think it's part of the pool while it is not.

    $ parted /dev/nvme0n1 rm
    Partition number? 3
    Information: You may need to update /etc/fstab.
   

7. Recreate the boot-pool partition as a 16GiB large partition with a sligtly later start sector than before, make sure that it is on a sector divisable with 2048 for best performance (526336 % 2048 = 0). We also do this to make sure that zfs doesn't find any metadata from the old partition.

   Start with the smaller disk if they are not identical.

    $ parted
    (parted) unit kiB
    (parted) select /dev/nvme0n1
    (parted) print
    Model: KINGSTON SNVS500GB (nvme)
    Disk /dev/nvme0n1: 488386584kiB
    Sector size (logical/physical): 512B/512B
    Partition Table: gpt
    Disk Flags:
   
    Number  Start    End        Size       File system  Name  Flags
     1      20.0kiB  1044kiB    1024kiB                       bios_grub
     2      1044kiB  525332kiB  524288kiB  fat32              boot, esp
   
    (parted) mkpart boot-pool 526336kiB 17303552kiB
    (parted) print
    Model: KINGSTON SNVS500GB (nvme)
    Disk /dev/nvme0n1: 488386584kiB
    Sector size (logical/physical): 512B/512B
    Partition Table: gpt
    Disk Flags:
   
    Number  Start      End          Size         File system  Name       Flags
     1      20.0kiB    1044kiB      1024kiB                              bios_grub
     2      1044kiB    525332kiB    524288kiB    fat32                   boot, esp
     3      526336kiB  17303552kiB  16777216kiB               boot-pool
   

8. Now you can create a partition allocating the rest of the disk.

    (parted) mkpart pool 17303552kiB 100%
    (parted) print
    Model: KINGSTON SNVS500GB (nvme)
    Disk /dev/nvme0n1: 488386584kiB
    Sector size (logical/physical): 512B/512B
    Partition Table: gpt
    Disk Flags:
   
    Number  Start        End           Size          File system  Name       Flags
     1      20.0kiB      1044kiB       1024kiB                               bios_grub
     2      1044kiB      525332kiB     524288kiB     fat32                   boot, esp
     3      526336kiB    17303552kiB   16777216kiB                boot-pool
     4      17303552kiB  488386560kiB  471083008kiB               pool
   

9. Do the same for the next device, but this time use the same values as in the printout above. We do this to make sure that the partitions are exactly the same size. In this example the disks are slightly different in size so using 100% on the second disk would create a partition larger than the one we just created on the smaller disk.

    (parted) select /dev/nvme1n1
    Using /dev/nvme1n1
    (parted) mkpart boot-pool 526336kiB 17303552kiB
    (parted) mkpart pool 17303552kiB 488386560kiB
    (parted) print
    Model: TS512GMTE220S (nvme)
    Disk /dev/nvme1n1: 500107608kiB
    Sector size (logical/physical): 512B/512B
    Partition Table: gpt
    Disk Flags:
   
    Number  Start        End           Size          File system  Name       Flags
     1      20.0kiB      1044kiB       1024kiB                               bios_grub
     2      1044kiB      525332kiB     524288kiB     fat32                   boot, esp
     3      526336kiB    17303552kiB   16777216kiB                boot-pool
     4      17303552kiB  488386560kiB  471083008kiB               pool
   

10. Make the new system partitions part of the boot-pool. This is done by attaching them to the existing pool while detaching the USB drive.

    $ zpool attach boot-pool sdb3 nvme0n1p3
    

    Wait for resilvering to complete, check progress with

    $ zpool status
    

    When resilvering is complete we can detach the USB device.

    $ zpool offline boot-pool sdb3
    $ zpool detach boot-pool sdb3
    

    Finally add the last drive to create a mirror of the boot-pool.

    $ zpool attach boot-pool nvme0n1p3 nvme1n1p3
    $ zpool status
    pool: boot-pool
    state: ONLINE
    scan: resilvered 2.78G in 00:00:03 with 0 errors on Wed Oct 27 07:16:56 2021
    config:
    
            NAME           STATE     READ WRITE CKSUM
            boot-pool      ONLINE       0     0     0
            mirror-0       ONLINE       0     0     0
                nvme0n1p3  ONLINE       0     0     0
                nvme1n1p3  ONLINE       0     0     0
    

    At this point you can remove the USB device and when the machine is rebooted it will start up from the NVMe devices instead. Check BIOS boot order if it doesn't.

11. Now that the boot-pool is mirrored we want to create a mirror pool using the remaining partitions.

    $ zpool create pool1 mirror nvme0n1p4 nvme1n1p4
    $ zpool status
    pool: boot-pool
    state: ONLINE
    scan: resilvered 2.78G in 00:00:03 with 0 errors on Wed Oct 27 07:16:56 2021
    config:
    
            NAME           STATE     READ WRITE CKSUM
            boot-pool      ONLINE       0     0     0
            mirror-0       ONLINE       0     0     0
                nvme0n1p3  ONLINE       0     0     0
                nvme1n1p3  ONLINE       0     0     0
    
    pool: pool1
    state: ONLINE
    config:
    
            NAME           STATE     READ WRITE CKSUM
            pool1          ONLINE       0     0     0
            mirror-0       ONLINE       0     0     0
                nvme0n1p4  ONLINE       0     0     0
                nvme1n1p4  ONLINE       0     0     0
    

    But to be able to import it in the Web UI we need to export it.

    $ zpool export pool1
    

12. All done! Import pool1 using the Web UI and start enjoying the additional space.

allowing TrueNAS to boot up for the first time

allowing TrueNAS to boot up for the first time will not do any harm

sed -i 's/sgdisk -n3:0:0/sgdisk -n3:0:+16384M/g' /usr/sbin/truenas-install /usr/sbin/truenas-install
this doesn't work anymore. Any suggestions?

sed -i 's/sgdisk -n3:0:0/sgdisk -n3:0:+16384M/g' /usr/sbin/truenas-install /usr/sbin/truenas-install this doesn't work anymore. Any suggestions?

the same with me. version: 23.10.0.1

sed -i 's/sgdisk -n3:0:0/sgdisk -n3:0:+16384M/g' /usr/sbin/truenas-install /usr/sbin/truenas-install this doesn't work anymore. Any suggestions?

The second /usr/sbin/truenas-install is a seperate command that you run after you sed because it will restart the installer with your new config you just made with sed. so after the sed command, hit enter to apply then run '/usr/sbin/truenas-install'

Is there a YT vid or screenshots based walk-through? n00b to Unix and the whole vi edit the file went over my head. I chose Shell instead of install, vi file path and it created a new file. Would love to use my NVMe for app instead of giving it all to the OS that'll use 10% of total space.

Use the sed command above (stands for 'streaming editor') which will modify the file on the fly without having to vi, just realize that the second /usr/sbin/truenas-install is a seperate command intended to run AFTER the sed command.

Thank you @gangefors (OP) for getting me started down this path and ultimately sorting thru his commands on which ones I needed.

I have a 16GB DOM (disk/device on module) coming in the mail and that is a capacity efficient but not cost effective way to use newer versions of TrueNAS at least until iXsystems comes up with a better way to install without wasting so much useful storage. But! Since I am waiting on the DOM and specialized power cable to arrive... I thought I would go ahead and try to get TrueNAS booting on my 500GB SSD and using the remaining space for my VM pool.

In my case I have a 500GB Samsung drive (usually dedicated for my VM machines and apps) and wanted TrueNAS boot to use 16GB while the rest was dedicated to my virtual machine/app environment which I will name: vmpool

DO AT YOUR OWN RISK. I AM CANNOT BE HELD RESPONSIBLE IF THIS IS WRONG OR HARMFUL TO YOUR DATA / SYSTEM

Boot into TrueNAS Scale installer and select shell:

parted -l|more

Find your device number and write it down in my case, my drive was /dev/sdi

Model: ATA Samsung SSD 850 (scsi)
Disk /dev/sdi: 500GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Disk Flags:

Number  Start   End     Size    File system  Name    Flags
 1      2097kB  3146kB  1049kB                       bios_grub, legacy_boot
 2      3146kB  540MB   537MB   fat32                boot, esp
 3      540MB   17.7GB  17.2GB  zfs

run 'parted' command to get you into prompt

# parted
(parted) unit kiB
(parted) select /dev/sdi
(parted) print

This should print the drive details you plan on expanding to use the rest of the drive

Number  Start        End           Size          File system  Name    Flags
 1      2048kiB      3072kiB       1024kiB                            bios_grub, legacy_boot
 2      3072kiB      527360kiB     524288kiB     fat32                boot, esp
 3      527360kiB    17304576kiB   16777216kiB   zfs

For the rest of my space, I want to dedicate this to my virtual machines and call this vmpool.
The important thing here is to create the pool at the END of the other pool hence why we need to give it the end kiB # followed by the 100% to make it use the rest of the drive space.

(parted) mkpart vmpool 17304576kiB 100%
(parted) print 
Model: ATA Samsung SSD 850 (scsi)
Disk /dev/sdi: 488386584kiB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Disk Flags:

Number  Start        End           Size          File system  Name    Flags
 1      2048kiB      3072kiB       1024kiB                            bios_grub, legacy_boot
 2      3072kiB      527360kiB     524288kiB     fat32                boot, esp
 3      527360kiB    17304576kiB   16777216kiB   zfs
 4      17304576kiB  488386560kiB  471081984kiB               vmpool

Now quit out of parted

(parted) quit

Back to the TrueNAS installer shell,
Now we need to make a zfs pool to export so the WebGUI will see it. We will need to use the new partition we just created

# zpool create vmpool /dev/sdi4
# zpool status 

You should see something without error that shows the pool you just created.
Now for the WebGUI to be able to see this, we just need to export this pool:

# zpool export vmpool

Reboot and boot into normal TrueNAS and NOT the installer, you should be able to go to the WebGUI and import pool and vmpool should show up.

From putty I ran zpool status and get this now after importing the pool:

root@truenas[~]# zpool status
  pool: boot-pool
 state: ONLINE
status: Some supported and requested features are not enabled on the pool.
        The pool can still be used, but some features are unavailable.
action: Enable all features using 'zpool upgrade'. Once this is done,
        the pool may no longer be accessible by software that does not support
        the features. See zpool-features(7) for details.
config:

        NAME        STATE     READ WRITE CKSUM
        boot-pool   ONLINE       0     0     0
          sdi3      ONLINE       0     0     0

errors: No known data errors

  pool: vmpool
 state: ONLINE
config:

        NAME                                    STATE     READ WRITE CKSUM
        vmpool                                  ONLINE       0     0     0
          3aee8bc4-0004-49c7-8845-85b86944769e  ONLINE       0     0     0

errors: No known data errors

You can also see my space in df -h

# root@truenas[~]# df -h |grep vmpool
vmpool                                                      435G  128K  435G   1% /mnt/vmpool

Thanks for contibuting to the guide @sta777ic.

So this article is super useful but missing exact instructions on how to just install TrueNAS to SSD and use the remaining space of the drive.

Creating a pool from the remaining space is detailed in the deprecated part of the guide that goes into how to set up a mirrored boot pool. The updated guide just covers the install part since that seemed what most people are looking for.

Just in case I might be dense, can someone please confirm which step we're supposed to pick up from in the deprecated instructions? Step 8?

... which step we're supposed to pick up from in the deprecated instructions?

Step 8 in the deprecated guide has instructions on how to allocate the remaining space to a partition. I've updated the guide to point to the exact bullet.

Success! I'm using the N5105 board with two 2TB nvme drives, my goal was to create a small boot partition for TrueNAS Scale (32GB) and use the rest for cache. I followed the guide to edit the /usr/sbin/truenas-install file and changed sgdisk -n3:0:0 to sgdisk -n3:0:+32768M.

At first I didn't continue with step 8. and just re-ran /usr/sbin/truenas-install and installed TrueNAS Scale. It installed, but didn't see the empty space. So, I plugged the USB back in to reboot and go into shell and followed step 8 and beyond that made sense:

 $ parted
 (parted) unit kiB
 (parted) select /dev/nvme0n1
 (parted) print
 # See where 32GB drive ends and use that as the beginning of the nvme-pool I'm about to create
 (parted) mkpart nvme-pool 17303552kiB 100%

Since my 2 nvme drives are the same sized, I could just select /dev/nvme1n1 and do mkpart nvme-pool 17303552kiB 100% again.

Next, was trial and error. zpool status didn't show anything. In the end, I figured out it was step 11 to create a mirror pool using the remaining partitions. It threw an error saying to use -f to force the command through:

$ zpool create nvme-pool mirror nvme0n1p5 nvme1n1p5
$ zpool status

(For me the boot pool was already mirrored at partition3 by TrueNAS's installation and doesn't have a name. The nvme-pool I created, when print in parted, showed it's at partition 5, hence nvme0n1p5.)

Now I can boot into TrueNAS and import the pool. Next step is to figure out if I really want to use it as cache, and how to do it. (I'm totally new to TrueNAS.

Thanks to everyone above.

This works flawlessly, I've been using my mirrored drive for about a year. But now, I've encounter the REAL problem of this method, one of my drive failed, and two pools including boot-pool is degraded. Rebulid the normal pool is fairly easy, but what about boot-pool and efi partition? Do I use dd to clone the partition? What if the drive is completely dead? Any hint is welcome.

This works flawlessly, I've been using my mirrored drive for about a year. But now, I've encounter the REAL problem of this method, one of my drive failed, and two pools including boot-pool is degraded. Rebulid the normal pool is fairly easy, but what about boot-pool and efi partition? Do I use dd to clone the partition? What if the drive is completely dead? Any hint is welcome.

this one was perfrectly working for me:
https://www.youtube.com/watch?v=m4zwJvzQ65s

4. Continue installing according to the official docs.
do NOT select "create 16GB Swap File"... during install of Truenas Scale 24.04.0
It will end with error:

Creating new GPT entries in memory.
The operation has completed succesfully.
Could not create partition 3 from 34609152 to 33554432
Could not change partition 3's type code to BF01!
Error encountered; not saving changes.
Could not do anything with nvme0n1, skipping
Disk is too small to install TrueNAS
The TrueNAS installation on nvme0n1 has failed. Press enter to continue...

Not making a Swap file seems to work.

Hi all and thank you for this tuto =)

@gangefors is it possible to add the continuation after the number 4 please?

II had trouble understanding in my case:

A user who uses a single NVME for boot and uses the second partition for apps.

5 . After installation select Shell

Execute : parted -l |more

Get your device name

6. Run parted

7. Select your NVME :

(parted)select /dev/nvme0n1

8. Create a partition :

• Use kiB :

(parted)unit kiB

• Get your starting size :

(parted)print

• Create partition :

mkpart pool 17303552kiB 100%

• Quit

(parted) quit

9. Create ZFS pool, check and export for WebGUI :

zpool create vmpool /dev/nvme1n1p4
zpool status 
zpool export vmpool

10. Reboot on TrueNas WebGui

11. On WebUi Storage => Import Pool, Select Pool and confirm

@gangefors is it possible to add the continuation after the number 4 please?

@gaetan-31 You've just added it to the guide :)

But to properly answer your question. This gist was written with the main purpose of document the creation of a boot partititon that is of a specific size (and mirroring it). I want to keep the guide as concise as possible.

The information about partitioning is available in the deprecated guide in step 8 (and partly in step 7) as is mentioned.

No problem ;)
Thank a lot any way =)

The suggested approach does not work for the next version (currently ElectricEel-24.10-BETA.1). Is there a simple solution for this as well?

In the beta a python script is used instead of the shell script.
The interesting part seems to be here:
https://github.com/truenas/truenas-installer/blob/40338b0e4b4bc0870001539ff4d7f4f64fd56d4f/truenas_installer/install.py#L81

I'll give it a trial tomorrow

Thanks for pointing me into the right direction! I tried the following and it seems to work.
sed -i 's/-n3:0:0/-n3:0:+16384M/g' /usr/lib/python3/dist-packages/truenas-installer/install.py

Then exit shell with Ctrl+D and continue installation.

Hello, I've read through this page and all it's comments about 10 times, the install process for me keeps failing. I have a new system build with 2x 1TB identical nvme. /dev/nvme0n1 & 1n1 show in parted etc. It appears the swb command works, it begins install, I can see creation of the partitions etc, it then proceeds to tell me "install on nvme0n1 & 1n1 failed, device is to small for install" I've tried this with 16GB & 32GB, with and without swap. Truing to install dragonfish 24.04. Any thoughts or direction would be much appreciated.

¡Gracias por indicarme la dirección correcta! Probé lo siguiente y parece que funciona. sed -i 's/-n3:0:0/-n3:0:+16384M/g' /usr/lib/python3/dist-packages/truenas-installer/install.py

Luego salga del shell con Ctrl+D y continúe con la instalación.

Estoy probando a instalarlo en una VM para ver que funciona antes de llevarlo a mi equipo actual. Hago lo siguiente, y veo que modifica la línea 84 del script de instalación, pero al instalar sólo puedo seleccionar el disco total y después al acceder en truenas a la pestaña disk, me dice que boot-pool esta usando el tamaño total del disco, ¿Qué ocurre? No funciona con la beta 24.10 de la web oficial de truenas?

Muchas gracias por su ayuda!

Did you try to let it run through? I also tested this in a VM and it is working, although TrueNAS tells me wrongly that the whole disk will be used.

Did you try to let it run through? I also tested this in a VM and it is working, although TrueNAS tells me wrongly that the whole disk will be used.

It has worked for me as follows:

1. I run the command:
   sed -i ‘s/-n3:0:0/-n3:0/-n3:0:+16384M/g’ /usr/lib/python3/dist-packages/truenas-installer/install.py.
2. I install TrueNAS and do not reboot.
3. I create the partition in the remaining space and follow the steps 7 - 12 of the USB guide.

So everything is fine, thank you very much @transfairs you are a crack!

Hi @oriaj3 there is a minor mistake in your command. It has to be:
sed -i ‘s/-n3:0:0/-n3:0:+16384M/g’ /usr/lib/python3/dist-packages/truenas-installer/install.py

(-n3:0/ has been duplicated in your command)
Cheers

The suggested approach does not work for the next version (currently ElectricEel-24.10-BETA.1). Is there a simple solution for this as well?

Hi, i've update to ElectricEel-24.10-RC.2 after install.
No problem with update.
It's fresh install ?

The recommendations didn't work for me, as the trueness installer folder is an underscore rather than a dash.
sed -i ‘s/-n3:0:0/-n3:0:+16384M/g’ /usr/lib/python3/dist-packages/truenas_installer/install.py

The recommendations didn't work for me, as the trueness installer folder is an underscore rather than a dash. sed -i ‘s/-n3:0:0/-n3:0:+16384M/g’ /usr/lib/python3/dist-packages/truenas_installer/install.py

+1

For TrueNas Scale, 24.10 (Electric Eel)
Missing parts in the initial guide.
Need to use some steps from the deprecated guide.

1. Login to shell (if you are connected to the NAS with a display, press 7 to get shell with root user).
2. Use parted to edit partitions.
3. Use print list to find your boot device, for me it was /dev/nvme0n1.
4. Use select <path to your boot device>.
5. Change units using unit kiB.
6. Use print to get exact info on your boot device current partition status.
7. Find the end of the last partition in your boot device (filesystem should be zfs) - for me it was 17304576kiB
8. Create the new partition using mkpart <new partition name> <last partition end in kiB> 100%, for me it was mkpart ssd-pool 17304576kiB 100%
9. Use print to verify (You can change to unit giB for ease of use). Note your new partition number (for me it was 4)
10. quit to exit parted.
11. To create a zpool, visible for Truenas, use zpool create <pool name> <path to your boot device>p<your new partition number>. (For me it was zpool create ssd-pool /dev/nvme0n1p4 ).
12. Received an error cannot mount '/ssd-pool': failed to create mountpoint: Read-only file system
13. Verified with zpool status that my pool was created.
14. Use zpool export <pool name> to allow Truenas Web UI to see this pool.
15. Verified in the web interface I can see the new zpool in the UI (Storage page, import pool).
16. exit to exit shell.

Some extras on how to create an encrypted pool (too much details, I put here some pointers and commands but I don't have time to add the exact details):

No Encryption:

zpool create ssd-pool /dev/nvme0n1p4
zpool export ssd-pool

With Encryption

openssl rand -hex 32 > /etc/ssd-pool.key
chmod 600 /etc/ssd-pool.key

zpool create -f -o ashift=12 -O acltype=posixacl -O compression=lz4 -O dnodesize=auto -O normalization=formD -O relatime=on -O xattr=sa -O encryption=aes-256-gcm -O keylocation=file:///etc/ssd-pool.key -O keyformat=hex -O mountpoint=none ssd-pool /dev/nvme0n1p4

zpool export ssd-pool

This will require also to manually copy the key from the shell to the webui when importing the pool

Adding second SSD and mirroring both boot-pool and ssd-pool

1. Make sure what is you new device path (under /dev) - for me /dev/nvme1n1.
2. Copy partition layout: sfdisk -d <first disk path> | sfdisk <new disk path> - for me sfdisk -d /dev/nvme0n1 | sfdisk /dev/nvme1n1.
3. Attach both partitions to existing pools, using zpool attach <pool name> <partition already in pool> <new partition added to pool>, for me - zpool attach boot-pool nvme0n1p3 nvme1n1p3 and zpool attach ssd-pool nvme0n1p4 nvme1n1p4

Validation of step 2 & 3 done with parted (print list) and zpool status respectively.