Synology DS212+ Serial Console Boot

gistfile1.txt

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** LOADER **
 ** MARVELL BOARD: Synology Disk Station LE

U-Boot 1.1.4 (Dec  2 2011 - 15:56:02) Marvell version: 3.5.9

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 0068B3D4

Soc: 88F6282 A1CPU running @ 2000Mhz L2 running @ 500Mhz
SysClock = 500Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM CS[1] base 0x10000000   size 256MB
DRAM Total size 512MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment

[4096kB@f8000000] Flash:  4 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: PCI Express Root Complex Interface
PEX interface detected Link X1

Synology Model: DS212+r1
Fan Status: Good

Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0
## Booting image at f8080000 ...
   Image Name:   Linux-2.6.32.12
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1476672 Bytes =  1.4 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at f8280000 ...
   Image Name:   synology_88f6282_212+ 2661
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    677043 Bytes = 661.2 kB
   Load Address: 00800000
   Entry Point:  00800000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Linux version 2.6.32.12 (root@build3) (gcc version 4.2.1) #2661 Mon Nov 12 23:10:15 CST 2012
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Synology 6282 board
[    0.000000] Using UBoot passing parameters structure
[    0.000000] Sys Clk = 200000000, Tclk = 166666667
[    0.000000] Synology Board ID: 27
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw     syno_hw_                                          version=DS212pv20 ihd_num=2 netif_num=1 esata_7042=1
[    0.000000] Synology Hareware Version: DS212pv20-j
[    0.000000] Internal HD num: 2
[    0.000000] Internal netif num: 1
[    0.000000] Esata chip use 7042: 1
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 256MB 256MB = 512MB total
[    0.000000] Memory: 506880KB available (3508K code, 530K data, 124K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 1985.74 BogoMIPS (lpj=9928704)
[    0.250000] Mount-cache hash table entries: 512
[    0.250000] CPU: Testing write buffer coherency: ok
[    0.250000] xor: measuring software checksum speed
[    0.300000]    arm4regs  :  1688.400 MB/sec
[    0.350000]    8regs     :  1372.400 MB/sec
[    0.400000]    32regs    :  1477.600 MB/sec
[    0.400000] xor: using function: arm4regs (1688.400 MB/sec)
[    0.400000] NET: Registered protocol family 16
[    0.400000] Feroceon L2: Enabling L2
[    0.400000] Feroceon L2: Cache support initialised, in WT override mode.
[    0.420000]
[    0.420000] CPU Interface
[    0.420000] -------------
[    0.420000] SDRAM_CS0 ....base 00000000, size 256MB
[    0.420000] SDRAM_CS1 ....base 10000000, size 256MB
[    0.420000] SDRAM_CS2 ....disable
[    0.420000] SDRAM_CS3 ....disable
[    0.420000] PEX0_MEM ....base e0000000, size 128MB
[    0.420000] PEX0_IO ....base f2000000, size   1MB
[    0.420000] PEX1_MEM ....base e8000000, size 128MB
[    0.420000] PEX1_IO ....base f2100000, size   1MB
[    0.420000] INTER_REGS ....base f1000000, size   1MB
[    0.420000] NFLASH_CS ....base fa000000, size   2MB
[    0.420000] SPI_CS ....base f4000000, size  16MB
[    0.420000] BOOT_ROM_CS ....no such
[    0.420000] DEV_BOOTCS ....no such
[    0.420000] CRYPT_ENG ....base f0000000, size   2MB
[    0.420000]  Detected Tclk 200000000 and SysClk 500000000
[    0.420000] Apply DS 212 GPIO
[    0.420000] Synology 6282 1, 2 bay GPIO Init
[    0.420000] PCIe link is enable, apply PCIe workaround
[    0.920000] PEX0 interface detected Link X4
[    1.420000] PEX1 interface detected Link X1
[    1.420000] PCI: bus0: Fast back to back transfers disabled
[    1.420000] pci 0000:01:01.0: PME# supported from D0 D3hot
[    1.420000] pci 0000:01:01.0: PME# disabled
[    1.420000] PCI: bus1: Fast back to back transfers disabled
[    1.430000] bio: create slab <bio-0> at 0
[    1.430000] vgaarb: loaded
[    1.430000] SCSI subsystem initialized
[    1.600000] raid6: int32x1    141 MB/s
[    1.770000] raid6: int32x2    169 MB/s
[    1.940000] raid6: int32x4    197 MB/s
[    2.110000] raid6: int32x8    175 MB/s
[    2.110000] raid6: using algorithm int32x4 (197 MB/s)
[    2.110000] Switching to clocksource kw_clocksource
[    2.110000] NET: Registered protocol family 2
[    2.110000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    2.110000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    2.110000] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[    2.110000] TCP: Hash tables configured (established 16384 bind 16384)
[    2.110000] TCP reno registered
[    2.110000] NET: Registered protocol family 1
[    2.110000] RPC: Registered udp transport module.
[    2.110000] RPC: Registered tcp transport module.
[    2.110000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    2.110000] Trying to unpack rootfs image as initramfs...
[    2.720000] rootfs image is not initramfs (no cpio magic); looks like an initrd
[    2.730000] Freeing initrd memory: 4096K
[    2.730000] XOR registered 4 channels
[    2.730000] XOR 2nd invalidate WA enabled
[    2.730000] VFS: Disk quotas dquot_6.5.2
[    2.730000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    2.730000] msgmni has been set to 998
[    2.730000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    2.730000] io scheduler noop registered
[    2.730000] io scheduler anticipatory registered (default)
[    2.740000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    2.740000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[    2.750000] console [ttyS0] enabled
[    2.760000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[    2.770000] brd: module loaded
[    2.770000] sata_mv sata_mv.0: version 1.28
[    2.770000] sata_mv sata_mv.0: slots 32 ports 2
[    2.780000] scsi0 : sata_mv
[    2.780000] scsi1 : sata_mv
[    2.790000] ata1: SATA max UDMA/133 irq 21
[    2.790000] ata2: SATA max UDMA/133 irq 21
[    6.140000] ata1: SATA link down (SStatus 0 SControl F300)
[    9.140000] Delay 5 seconds to wait for disk 2 ready.
[   19.320000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[   19.520000] ata2.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133
[   19.520000] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[   19.570000] ata2.00: configured for UDMA/133
[   19.570000] scsi 1:0:0:0: Direct-Access     WDC      WD20EARX-00PASB0 51.0 PQ: 0 ANSI: 5
[   19.580000] sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[   19.590000] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[   19.590000] sd 1:0:0:0: [sdb] Write Protect is off
[   19.600000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   19.610000]  sdb: sdb1 sdb2
[   19.620000] sd 1:0:0:0: [sdb] Attached SCSI disk
[   19.630000] sata_mv 0000:00:01.0: version 1.28
[   19.630000] PCI: enabling device 0000:00:01.0 (0140 -> 0143)
[   19.640000] sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[   19.650000] scsi2 : sata_mv
[   19.650000] scsi3 : sata_mv
[   19.650000] scsi4 : sata_mv
[   19.660000] scsi5 : sata_mv
[   19.660000] ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 9
[   19.670000] ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 9
[   19.670000] ata5: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 9
[   19.680000] ata6: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 9
[   20.040000] ata3: SATA link down (SStatus 0 SControl 300)
[   20.390000] ata4: SATA link down (SStatus 0 SControl 300)
[   20.740000] ata5: SATA link down (SStatus 0 SControl 300)
[   21.090000] ata6: SATA link down (SStatus 0 SControl 300)
[   21.090000] physmap platform flash device: 00400000 at f8000000
[   21.100000] SPI Serial flash detected @ 0xf8000000, 4096KB (64sec x 64KB)
[   21.110000] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x3f0000
[   21.120000] 6 RedBoot partitions found on MTD device SYNOMTD-0
[   21.120000] SYNOMTD flash bank 0: Using RedBoot partition definition
[   21.130000] Creating 6 MTD partitions on "SYNOMTD-0":
[   21.140000] 0x000000000000-0x000000080000 : "RedBoot"
[   21.140000] 0x000000080000-0x000000280000 : "zImage"
[   21.150000] 0x000000280000-0x0000003c0000 : "rd.gz"
[   21.150000] 0x0000003c0000-0x0000003d0000 : "vendor"
[   21.160000] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[   21.160000] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[   21.170000] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[   21.180000] Serial Number: C1KNNxxxxx
[   21.180000] 0x0000003d0000-0x0000003f0000 : "RedBoot Config"
[   21.190000] 0x0000003f0000-0x000000400000 : "FIS directory"
[   21.190000] SPI Serial flash detected @ 0xf4000000, 4096KB (64sec x 64KB)
[   21.200000] cmdlinepart partition parsing not available
[   21.210000] Loading Marvell Ethernet Driver:
[   21.210000]   o Cached descriptors in DRAM
[   21.220000]   o DRAM SW cache-coherency
[   21.220000]   o 2 Giga ports supported
[   21.220000]   o Single RX Queue support - ETH_DEF_RXQ=0
[   21.230000]   o Single TX Queue support - ETH_DEF_TXQ=0
[   21.230000]   o TCP segmentation offload (TSO) supported
[   21.240000]   o Receive checksum offload supported
[   21.240000]   o Transmit checksum offload supported
[   21.250000]   o SKB Recycle supported - (Enabled)
[   21.250000]   o Rx descripors: q0=128
[   21.260000]   o Tx descripors: q0=532
[   21.260000]   o Loading network interface(s):
[   21.270000]     o  register under mv88fx_eth platform
[   21.270000]     o eth0, ifindex = 2, GbE port = 0
[   21.280000]     o eth0, phy chipid = 1410e90, Support WOL = 32
[   21.280000]
[   21.280000] md: linear personality registered for level -1
[   21.290000] md: raid0 personality registered for level 0
[   21.290000] md: raid1 personality registered for level 1
[   21.300000] md: raid10 personality registered for level 10
[   21.310000] md: raid6 personality registered for level 6
[   21.310000] md: raid5 personality registered for level 5
[   21.320000] md: raid4 personality registered for level 4
[   21.320000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: [email protected]
[   21.330000] cpuidle: using governor ladder
[   21.330000] TCP cubic registered
[   21.340000] NET: Registered protocol family 17
[   21.340000] md: Waiting for all devices to be available before autodetect
[   21.350000] md: If you don't use raid, use raid=noautodetect
[   21.360000] md: Autodetecting RAID arrays.
[   21.370000] md: Scanned 2 and added 2 devices.
[   21.380000] md: autorun ...
[   21.380000] md: considering sdb1 ...
[   21.390000] md:  adding sdb1 ...
[   21.390000] md: sdb2 has different UUID to sdb1
[   21.390000] md: created md0
[   21.400000] md: bind<sdb1>
[   21.400000] md: running: <sdb1>
[   21.400000] raid1: raid set md0 active with 1 out of 2 mirrors
[   21.410000] md0: detected capacity change from 0 to 2549940224
[   21.410000] md: considering sdb2 ...
[   21.420000] md:  adding sdb2 ...
[   21.420000] md: created md1
[   21.420000] md: bind<sdb2>
[   21.430000] md: running: <sdb2>
[   21.430000] raid1: raid set md1 active with 1 out of 2 mirrors
[   21.440000] md1: detected capacity change from 0 to 2147418112
[   21.440000] md: ... autorun DONE.
[   21.450000] RAMDISK: lzma image found at block 0
[   22.130000] VFS: Mounted root (ext2 filesystem) on device 1:0.
START /linuxrc.syno
[   22.150000] ds212+_synobios: module license 'Synology Inc.' taints kernel.
[   22.160000] Disabling lock debugging due to kernel taint
[   22.200000] correction with 0x0f
[   22.260000] synobios: load, major number 201
[   22.260000] Brand: Synology
[   22.270000] Model: DS-212+
[   22.270000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
mknod: /dev/synobios: File exists
Starting /usr/syno/bin/synocfgen...
/usr/syno/bin/synocfgen returns 0
[   22.300000] synobios: unload
Partition Version=7
 /sbin/e2fsck exists, checking /dev/md0...
[   22.340000]  md0: unknown partition table

   16112 inodes used (10.35%)
       3 non-contiguous files (0.0%)
       2 non-contiguous directories (0.0%)
         # of inodes with ind/dind/tind blocks: 0/0/0
         Extent depth histogram: 13447/1
  117302 blocks used (18.84%)
       0 bad blocks
       1 large file

   11628 regular files
    1818 directories
     146 character device files
    1805 block device files
       0 fifos
       3 links
     704 symbolic links (702 fast symbolic links)
       2 sockets
--------
   16106 files
/sbin/e2fsck returns 0
Mounting /dev/md0 /tmpRoot
[   23.070000] EXT4-fs (md0): barriers disabled
[   23.080000] EXT4-fs (md0): mounted filesystem with ordered data mode
------------upgrade
use default /dev/md0
Begin upgrade procedure
No upgrade file exists
End upgrade procedure
============upgrade
/dev/md0 /tmpRoot ext4 rw,relatime,barrier=0,journal_checksum,data=ordered 0 0
[   23.450000] synoacl module [synoacl_ext4] is not loaded
[   23.450000] synoacl module [synoacl_vfs] is not loaded
none /sys sysfs rw,relatime 0 0
linuxrc.syno executed successfully.
[   23.490000] EXT3-fs: md0: couldn't mount because of unsupported optional features (240).
[   23.490000] EXT2-fs: md0: couldn't mount because of unsupported optional features (240).
[   23.510000] EXT4-fs (md0): barriers disabled
[   23.530000] EXT4-fs (md0): mounted filesystem with ordered data mode
[   23.530000] VFS: Mounted root (ext4 filesystem) on device 9:0.
[   23.540000] Trying to move old root to /initrd ... okay
[   23.560000] Freeing init memory: 124K
:: Starting /etc/rc
:: Prepare var ... [  OK  ]
:: Mounting procfs ... [  OK  ]
:: Mounting tmpfs ... [  OK  ]
:: Mounting devpts ... [  OK  ]
:: Mounting sysfs ... [  OK  ]
:: Checking new disks ...
No new disk. Do nothing.
[   25.450000]  md1: unknown partition table
[   25.470000] Adding 2097080k swap on /dev/md1.  Priority:-1 extents:1 across:2097080k
/dev/root on / type ext4 (rw,relatime,barrier=0,journal_checksum,data=ordered)
/tmp on /tmp type tmpfs (0)
none on /dev/pts type devpts (gid=4,mode=620)
/sys on /sys type sysfs (0)
Hostname DiskStation
192.168.3.121   DiskStation
:: Loading module ipv6[   25.780000] NET: Registered protocol family 10
[   25.780000] lo: Disabled Privacy Extensions
 ... [  OK  ]
:: Loading module llc ... [  OK  ]
:: Loading module psnap ... [  OK  ]
:: Loading module sg[   25.870000] sd 1:0:0:0: Attached scsi generic sg0 type 0
 ... [  OK  ]
:: Loading module usbcore[   26.000000] usbcore: registered new interface driver usbfs
[   26.010000] usbcore: registered new interface driver hub
[   26.010000] usbcore: registered new interface driver ethub
[   26.040000] usbcore: registered new device driver usb
 ... [  OK  ]
:: Loading module quota_tree ... [  OK  ]
:: Loading module quota_v2 ... [  OK  ]
:: Loading module crc-ccitt ... [  OK  ]
:: Loading module crc-itu-t ... [  OK  ]
:: Loading module dm-snapshot ... [  OK  ]
:: Loading module freq_table ... [  OK  ]
:: Loading module cpufreq_stats ... [  OK  ]
:: Loading module cpufreq[   26.190000] cpufreq: Init kirkwood cpufreq driver
 ... [  OK  ]
:: Loading module crypto_algapi ... [  OK  ]
:: Loading module crypto_wq ... [  OK  ]
:: Loading module crypto_blkcipher ... [  OK  ]
:: Loading module crypto_hash ... [  OK  ]
:: Loading module aead ... [  OK  ]
:: Loading module pcompress ... [  OK  ]
:: Loading module cryptomgr ... [  OK  ]
:: Loading module cbc ... [  OK  ]
:: Loading module md5[   26.410000] alg: No test for md5 (md5-generic)
 ... [  OK  ]
:: Loading module aes_generic[   26.440000] alg: No test for aes (aes-generic)
 ... [  OK  ]
:: Loading module rng ... [  OK  ]
:: Loading module ansi_cprng[   26.480000] alg: No test for stdrng (ansi_cprng)
 ... [  OK  ]
:: Loading module krng[   26.490000] alg: No test for stdrng (krng)
 ... [  OK  ]
:: Loading module eseqiv ... [  OK  ]
:: Loading module crc32c[   26.530000] alg: No test for crc32c (crc32c-generic)
 ... [  OK  ]
:: Loading module des_generic[   26.550000] alg: No test for des (des-generic)
[   26.560000] alg: No test for des3_ede (des3_ede-generic)
 ... [  OK  ]
:: Loading module chainiv ... [  OK  ]
:: Loading module ocf ... [  OK  ]
:: Loading module cryptodev ... [  OK  ]
:: Loading module cesa_dev[   26.640000] cesadev_init(bf182000)
 ... [  OK  ]
:: Loading module cesa_ocf_drv[   26.660000] mvCesaInit: sessions=10240, queue=64, pSram=f0000000
 ... [  OK  ]
:: Loading module ecb ... [  OK  ]
:: Loading module sha1_generic[   26.710000] alg: No test for sha1 (sha1-generic)
 ... [  OK  ]
:: Loading module sha256_generic[   26.720000] alg: No test for sha224 (sha224-generic)
[   26.730000] alg: No test for sha256 (sha256-generic)
 ... [  OK  ]
:: Loading module sha512_generic[   26.750000] alg: No test for sha384 (sha384-generic)
[   26.760000] alg: No test for sha512 (sha512-generic)
 ... [  OK  ]
:: Loading module ecryptfs[   26.810000] encryptfs using the OCF package.
 ... [  OK  ]
:: Loading module cryptosoft ... [  OK  ]
:: Loading module fat ... [  OK  ]
:: Loading module vfat ... [  OK  ]
:: Loading module fuse[   26.970000] fuse init (API version 7.13)
 ... [  OK  ]
:: Loading module hfsplus ... [  OK  ]
:: Loading module synoacl_vfs ... [  OK  ]
:: Loading module synoacl_ext4 ... [  OK  ]
:: Mounting usbfs ... [  OK  ]
:: Loading module sky2[   27.110000] sky2 driver version 1.25
 ... [  OK  ]
:: Loading module synobios[   27.200000] correction with 0x0f
[   27.250000] synobios: load, major number 201
[   27.260000] Brand: Synology
[   27.260000] Model: DS-212+
[   27.260000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
 ... [  OK  ]
synochecknetworkcfg: Pass
[   27.600000] eth0: mac address changed
[   29.670000] eth0: link down
[   29.670000] eth0: started
[   29.670000] ADDRCONF(NETDEV_UP): eth0: link is not ready
eth0      Link encap:Ethernet  HWaddr 00:11:32:11:18:F3
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:532
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:11

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
      [   30.730000] eth0: link up    inet6 addr: , full duplex::1/128 Scope:Ho, speed 1 Gbpsst
          UP
 LOOPBACK RUNNIN[   30.740000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
G  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

ls: /etc/dhcpd/dhcpd-*.conf: No such file or directory
ls: /etc/dhcpd/dhcpd-*.info: No such file or directory
grep: /etc/dhcpd/dhcpd.info: No such file or directory
kernel.panic = 3
:: Starting syslogd ... [  OK  ]
Pass s00_synocheckfstab ...
Pass CheckSynoinfo ...
Pass CheckUser
Pass CheckSmbConf ...
Pass CheckCronTab ...
Pass CheckGroup.
Pass s62_synocheckapple ...
start findhostd
synokerneltz: set kernel time zone to 300
kernel.core_pattern = /volume1/@%e.core
fs.suid_dumpable = 2
vm.min_free_kbytes = 8192
:: Starting scemd
[   37.980000] ata2.00: configured for UDMA/133
[   37.980000] ata2: EH complete
:: Starting services in background
[   38.170000] ata2.00: Disable disk write cache in EH:: Loading module ehci-hcd
[   38.270000] ata2.00: configured for UDMA/133
[   38.270000] ata2: EH complete
[   38.270000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   38.310000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   38.310000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[   38.320000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   38.360000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   38.380000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   38.380000] usb usb1: configuration #1 chosen from 1 choice
[   38.400000] hub 1-0:1.0: USB hub found
[   38.400000] hub 1-0:1.0: 1 port detected
 ... [  OK  ]
:: Loading module ohci-hcd[   38.510000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
 ... [  OK  ]
:: Loading module xhci-hcd[   38.600000] xhci_hcd 0000:01:01.0: xHCI Host Controller
[   38.610000] xhci_hcd 0000:01:01.0: new USB bus registered, assigned bus number 2
[   38.610000] xhci_hcd 0000:01:01.0: irq 10, io mem 0xe8000000
[   38.680000] usb usb2: No SuperSpeed endpoint companion for config 1  interface 0 altsetting 0 ep 129: using minimum values
[   38.730000] usb usb2: configuration #1 chosen from 1 choice
[   38.730000] hub 2-0:1.0: USB hub found
[   38.740000] hub 2-0:1.0: 4 ports detected
[   38.740000] usb 1-1: new high speed USB device using orion-ehci and address 2
 ... [  OK  ]
:: Loading module etxhci-hcd[   38.930000] Got empty serial number. Generate serial number from product.
[   38.940000] usb 1-1: configuration #1 chosen from 1 choice
[   38.950000] hub 1-1:1.0: USB hub found
[   38.950000] hub 1-1:1.0: 4 ports detected
 ... [  OK  ]
:: Loading module usb-storage[   39.070000] Initializing USB Mass Storage driver...
[   39.080000] usbcore: registered new interface driver usb-storage
[   39.090000] USB Mass Storage support registered.
 ... [  OK  ]
:: Loading module usblp[   39.240000] usb 1-1.4: new high speed USB device using orion-ehci and address 3
[   39.250000] usbcore: registered new interface driver usblp
No rules exists, remove tc modules...
cat: can't open '/proc/net/ip6_tables_names': No such file or directory
Tc modules has not been started...
cat: can't open '/proc/net/ip_tables_names': No such file or directory
 ... [  OK  ]
:: Loading module hid[   39.350000] usb 1-1.4: configuration #1 chosen from 1 choice
[   39.360000] scsi6 : SCSI emulation for USB Mass Storage devices
Tc modules has not been started...
 ... [  OK  ]
:: Loading module usbhid[   39.600000] usbcore: registered new interface driver hiddev
[   39.660000] usbcore: registered new interface driver usbhid
[   39.660000] usbhid: v2.6:USB HID core driver
 ... [  OK  ]
startup daemons
Sat Dec  1 22:12:31 EST 2012

 Disk Usage Status:
        [sdb]
 --------------------------------
 [md0]:  [1]
 [md1]:  [1]
 Partition Layout Version:
/dev/sdb: [V7]
synocheckvolume: Pass
synocheckshare: Pass SYNOICheckShare()
synocheckshare: Pass SYNOICheckShareExt()
synocheckshare: Pass SYNOICheckServiceLink()
synocheckshare: Pass SYNOICheckAutoDecrypt()
synocheckshare: Pass SYNOIServiceShareEnableDefaultDS()
synocheckiscsitrg: Pass
synobootup: BEGIN
synobootup: END
Starting Hotplug Handling Daemon ...

DiskStation login: Starting inetd...
Starting crond...
 Starting Snmpd
synorelayd is not configured
MySQL is not enabled. Skip...
Syslog setting file does not exist!
Syslog-ng server start...
Client/Server is both disabled
PGSQL service is disabled. Skip...
CUPS: Starting cupsd...
CUPS: Never Start CUPS until volume exist...
GCP: cupsd not running, skip start gcpd
start S2S daemons ...
Starting Synology File Indexing Daemon ...
PGSQL service is disabled. Skip...
Starting Synology Make Thumb Daemon...
[   44.460000] scsi 6:0:0:0: Direct-Access     Generic  STORAGE DEVICE   9910 PQ: 0 ANSI: 0
[   44.470000] sd 6:0:0:0: Attached scsi generic sg1 type 0
[   44.490000] scsi 6:0:0:1: Direct-Access     Generic  STORAGE DEVICE   9910 PQ: 0 ANSI: 0
[   44.520000] sd 6:0:0:0: [sdq] Attached SCSI removable disk
[   44.590000] sd 6:0:0:1: Attached scsi generic sg2 type 0
[   44.610000] sd 6:0:0:1: [sdr] Attached SCSI removable disk
:: Running lunbackup garbage collection ... [  OK  ]
:: No iSCSI targets enabled, skip it.
:: No iSCSI VAAI lun in trash can, skip it.
remove temp tdbs
start nmbd ... ok
start smbd ...
check tdb: /usr/syno/etc/private/secrets.tdb ... done
check tdb: /var/run/account_policy.tdb ... done
check tdb: /var/run/share_info.tdb ... done
check tdb: /var/run/registry.tdb ... done
done
Load loop.ko ...
[   46.840000] loop: module loaded
Load isofs.ko ...
Load udf.ko ...
Load cifs.ko ...
[   47.740000] Slow work thread pool: Starting up
[   48.070000] Slow work thread pool: Ready
Starting Netatalk services (this will take a while):
 cnid_metad afpd (DiskStation:AFPServer).
NFS server is not enabled. Skip...
Starting Synology Make FLV Daemon ...
Start SSH...

 Starting Synosnmpcd
Start System Apache Server .....  -f /usr/syno/apache/conf/httpd.conf-sys
/usr/syno/etc/rc.d/S97apache-sys.sh: system httpd started
Start User Apache Server .....
/usr/syno/etc/rc.d/S97apache-user.sh: user httpd started
LoadModule synobandwidth_module modules/mod_synobandwidth.so
start findhostd
/var/spool/synoeaupgrade.list doesn't exist!
Stop upgarde
We only disalbe WD idle3 timer when DS down, please call /usr/syno/etc/rc.d/S99WDidle3Dis.sh stop
Starting Avahi mDNS/DNS-SD Daemon
SFTP is not enabled. Skip running SFTP
[   51.280000] findhostd uses obsolete (PF_INET,SOCK_PACKET)
[  118.290000] ata1: device plugged sstatus 0x123
[  118.300000] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xe frozen
[  118.310000] ata1: edma_err_cause=00000010 pp_flags=00000000, dev connect
[  118.310000] ata1: SError: { PHYRdyChg DevExch }
[  118.320000] ata1: hard resetting link
[  124.270000] ata1: link is slow to respond, please be patient (ready=0)
[  128.350000] ata1: SRST failed (errno=-16)
[  128.350000] ata1: SRST fail, set srst fail flag
[  128.350000] ata1: hard resetting link
[  130.780000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[  130.780000] ata1: link reset sucessfully clear error flags
[  130.810000] ata1.00: ATA-8: SAMSUNG HD203WI, 1AN10003, max UDMA/133
[  130.810000] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[  130.840000] ata1.00: configured for UDMA/133
[  130.840000] ata1: EH complete
[  130.840000] scsi 0:0:0:0: Direct-Access     SAMSUNG  HD203WI          1AN1 PQ: 0 ANSI: 5
[  130.860000] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[  130.870000] sd 0:0:0:0: Attached scsi generic sg3 type 0
[  130.900000] sd 0:0:0:0: [sda] Write Protect is off
[  130.920000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  130.940000]  sda: sda1 sda2 sda3 < sda5 >
[  130.980000] sd 0:0:0:0: [sda] Attached SCSI disk
[  137.810000] ata2.00: skip command 0xef feature 0x2
[  137.850000] ata1.00: configured for UDMA/133
[  137.850000] ata1: EH complete