Kernel TTY muckup somewhere

gistfile1.txt

==============================
Using Dataflash!
 ba_offset = 0xb ...
AT91Bootstrap 3.7.1-00054-gef803bb-dirty (Sun Mar 15 19:00:41 PDT 2015)
Edited by hak8or!
Yey custom code execution and toolchain verification! :D
======--======--======--======
MASTER_CLOCK (MCLK): 0x5f5e100
SPI clock rate requested: 0xa1220
scbr: 0x97
SF: Got Manufacturer and Device ID:0x1f 0x25 0x0 0x1 0x0
SF: Copy 0x55500 bytes from 0x8400 to 0x20008400
SF: Done loading image from SerialFlash
Jumping to JUMP_ADDR (0x20008400) ...


U-Boot 2014.07-00058-gb44bde2-dirty (Mar 16 2015 - 07:19:40)

CPU: AT91SAM9N12
Crystal frequency:       16 MHz
CPU clock        :  301.333 MHz
Master clock     :  100.444 MHz
DRAM:  64 MiB
WARNING: Caches not enabled
NAND:  atmel_nand: Fail to initialize #0 chip0 MiB
MMC:   mci: 0
** Bad device usb 0 **
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ks8851_mll: Invalid chip id 0x30c0
Board Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
U-Boot> usb start
(Re)start USB...
USB0:   scanning bus 0 for devices... ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did
not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did
not provide a handshake (OUT) (5)
1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
U-Boot> usb stop
stopping USB..
U-Boot> usb start
(Re)start USB...
USB0:   scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
U-Boot> printenv
baudrate=115200
bootargs_mmc=root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait
bootargs_nand=rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs rw
bootargs_usb=root=/dev/sda2 rootwait ro rootfstype=ext2 init=/bin/init
bootcmd=setenv bootargs ${console} ${bootargs_usb};
bootdelay=3
console=console=ttyS0,115200
mtdparts=mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256k(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs)

Environment size: 455/16380 bytes
U-Boot> fatload usb 0:1 0x20000000 uimage.bin; bootm;
reading uimage.bin
1515300 bytes read in 4075 ms (362.3 KiB/s)
## Booting kernel from Legacy Image at 20000000 ...
   Image Name:   linux-2.6
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1515236 Bytes = 1.4 MiB
   Load Address: 20008000
   Entry Point:  20008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.39 (hak8or@ubuntu) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-29) ) #5 Mon Mar 16 07:24:35 EDT 2015
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Atmel AT91SAM9N12-EK
Memory policy: ECC disabled, Data cache writeback
Clocks: CPU 301 MHz, master 100 MHz, main 16.000 MHz
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rootwait ro rootfstype=ext2 init=/bin/init
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61728k/61728k available, 3808k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xff000000 - 0xffe00000   (  14 MB)
    vmalloc : 0xc4800000 - 0xfee00000   ( 934 MB)
    lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc0027000   ( 124 kB)
      .text : 0xc0027000 - 0xc02de000   (2780 kB)
      .data : 0xc02de000 - 0xc02fcac0   ( 123 kB)
NR_IRQS:192
AT91: 128 gpio irqs in 4 banks
Console: colour dummy device 80x30
console [ttyS0] enabled
Calibrating delay loop... 149.91 BogoMIPS (lpj=749568)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
AT91: Power Management (with slow clock mode)
AT91: Starting after power-restored wakeup
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-gpio i2c-gpio.0: using pins 62 (SDA) and 63 (SCL)
at_hdmac at_hdmac.0: Atmel AHB DMA Controller ( cpy slave ), 8 channels
Advanced Linux Sound Architecture Driver Version 1.0.24.
Switching to clocksource tcb_clksrc
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 120
io scheduler noop registered (default)
atmel_hlcdfb atmel_hlcdfb_base.0: 510KiB frame buffer at 23980000 (mapped at ffd80000)
Console: switching to colour frame buffer device 60x34
atmel_hlcdfb atmel_hlcdfb_base.0: fb0: Atmel LCDC at 0xf8038000 (mapped at c486e000), irq 25
atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL
brd: module loaded
loop: module loaded
ssc ssc.0: Atmel SSC device at 0xc4878000 (irq 28)
atmel_nand atmel_nand: Using dma0chan0 for DMA transfers.
nand_get_flash_type: second ID read did not match 30,30 against f6,00
No NAND device found.
atmel_spi atmel_spi.0: Using dma0chan0 (tx) and  dma0chan1 (rx) for DMA transfers
atmel_spi atmel_spi.0: Atmel SPI Controller at 0xf0000000 (irq 13)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
at91_ohci at91_ohci: AT91 OHCI
at91_ohci at91_ohci: new USB bus registered, assigned bus number 1
at91_ohci at91_ohci: irq 22, io mem 0x00500000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
udc: at91_udc version 3 May 2006
mousedev: PS/2 mouse device common for all mice
input: gpio-keys as /devices/platform/gpio-keys/input/input0
qt1070 0-001b: can not read register, returned -6
qt1070 0-001b: ID -6 not supported
atmel_tsadcc atmel_tsadcc: Master clock is set at: 100444438 Hz
atmel_tsadcc atmel_tsadcc: Prescaler is set at: 166
input: atmel touch screen controller as /devices/platform/atmel_tsadcc/input/input1
at91_rtc at91_rtc: rtc core: registered at91_rtc as rtc0
AT91 Real Time Clock driver.
i2c /dev entries driver
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
ASoC: Setting pck0 to 32768Hz
wm8904-codec 0-001a: i2c_transfer() returned -6
wm8904-codec 0-001a: Device is not a WM8904, ID is 0
wm8904-codec 0-001a: asoc: failed to probe CODEC wm8904-codec.0-001a: -22
asoc: failed to instantiate card WM8904 @ AT91SAM9N12: -22
ASoC: at91sam9n12_init ok
ALSA device list:
  No soundcards found.
at91_rtc at91_rtc: setting system clock to 2007-01-01 00:00:49 UTC (1167609649)
atmel_mci atmel_mci.0: Using dma0chan2 for DMA transfers
atmel_mci atmel_mci.0: Atmel MCI controller at 0xf0008000 irq 12, 1 slots
Waiting for root device /dev/sda2...
usb 1-1: new full speed USB device number 2 using at91_ohci
scsi0 : usb-storage 1-1:1.0
scsi 0:0:0:0: Direct-Access     OCZ      DIESEL           PMAP PQ: 0 ANSI: 0 CCS
sd 0:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: detected capacity change from 0 to 16039018496
 sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
VFS: Mounted root (ext2 filesystem) readonly on device 8:2.
Freeing init memory: 124K
can't run '/etc/init.d/rcS': No such file or directory

can't open /dev/tty2: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty2: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty2: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty2: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty2: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty2: No such file or directory
can't open /dev/tty2: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty2: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty2: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty2: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty2: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty2: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty2: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty2: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty2: No such file or directory
can't open /dev/tty2: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty2: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty4: No such file or directory
can't open /dev/tty3: No such file or directory
can't open /dev/tty2: No such file or directory
▒