U-BOOT WORKS!!!! :D :D :D :D This means I finally got code execution working from DRAM! :D DRAM clk only at 100 Mhz instead of 133 Mhz but ah well.

gistfile1.txt

Contents at 0x2005d8ec : 0xffffffff
Contents at 0x2005d8f0 : 0xffffffff
Contents at 0x2005d8f4 : 0xffffffff
Contents at 0x2005d8f8 : 0xffffffff
Contents at 0x2005d8fc : 0xffffffff
Jumping to JUMP_ADDR (0x20008400) ...


U-Boot 2014.07-00058-gb44bde2-dirty (Mar 15 2015 - 01:53:35)

CPU: AT91SAM9N12
Crystal frequency:       16 MHz
CPU clock        :  301.333 MHz
Master clock     :  100.444 MHz
DRAM:  64 MiB
WARNING: Caches not enabled
NAND:  atmel_nand: Fail to initialize #0 chip0 MiB
MMC:   mci: 0
SF: Detected AT45DB081D with page size 256 Bytes, erase size 4 KiB, tot                                               al 1 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ks8851_mll: Invalid chip id 0x30c0
Board Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
SF: Detected AT45DB081D with page size 256 Bytes, erase size 4 KiB, tot                                               al 1 MiB
ERROR: attempting read past flash size (0x100000)
Wrong Image Format for bootm command
ERROR: can't get kernel image!
U-Boot>ls
Unknown command 'ls' - try 'help'
U-Boot> base
Base Address: 0x00000000
U-Boot> md 0 c
00000000: ea00000e ea000005 ea000005 ea000005    ................
00000010: ea000005 00001ed0 ea000006 ea000006    ................
00000020: eafffffe eafffffe eafffffe e25ef004    ..............^.
U-Boot> help mtest
Unknown command 'mtest' - try 'help' without arguments for list of all known commands

U-Boot> help
?       - alias for 'help'
base    - print or set address offset
bdinfo  - print Board Info structure
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootm   - boot application image from memory
bootp   - boot image via network using BOOTP/TFTP protocol
bootz   - boot Linux zImage image from memory
chpart  - change active partition
cls     - clear screen
cmp     - memory compare
coninfo - print console devices and information
cp      - memory copy
crc32   - checksum calculation
dhcp    - boot image via network using DHCP/TFTP protocol
echo    - echo args to console
editenv - edit environment variable
env     - environment handling commands
exit    - exit script
false   - do nothing, unsuccessfully
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
fdt     - flattened device tree utility commands
go      - start application at address 'addr'
help    - print command description/usage
iminfo  - print header information for application image
imxtract- extract a part of a multi-image
itest   - return true/false on integer compare
loadb   - load binary file over serial line (kermit mode)
loads   - load S-Record file over serial line
loadx   - load binary file over serial line (xmodem mode)
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
md      - memory display
mm      - memory modify (auto-incrementing address)
mmc     - MMC sub system
mmcinfo - display MMC info
mtdparts- define flash/nand partitions
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
nfs     - boot image via network using NFS protocol
nm      - memory modify (constant address)
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv  - set environment variables
sf      - SPI flash sub-system
showvar - print local hushshell variables
sleep   - delay execution for some time
source  - run script from memory
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
true    - do nothing, successfully
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor, compiler and linker version
U-Boot> sf
sf - SPI flash sub-system

Usage:
sf probe [[bus:]cs] [hz] [mode] - init flash device on given SPI bus
                                  and chip select
sf read addr offset len - read `len' bytes starting at
                                  `offset' to memory at `addr'
sf write addr offset len        - write `len' bytes from memory
                                  at `addr' to flash at `offset'
sf erase offset [+]len          - erase `len' bytes from `offset'
                                  `+len' round up `len' to block size
sf update addr offset len       - erase and write `len' bytes from memory
                                  at `addr' to flash at `offset'
U-Boot> test
U-Boot> md 0 c
00000000: ea00000e ea000005 ea000005 ea000005    ................
00000010: ea000005 00001ed0 ea000006 ea000006    ................
00000020: eafffffe eafffffe eafffffe e25ef004    ..............^.
U-Boot> md 0
00000000: ea00000e ea000005 ea000005 ea000005    ................
00000010: ea000005 00001ed0 ea000006 ea000006    ................
00000020: eafffffe eafffffe eafffffe e25ef004    ..............^.
U-Boot> help md
md - memory display

Usage:
md [.b, .w, .l] address [# of objects]
U-Boot> md 0 20
00000000: ea00000e ea000005 ea000005 ea000005    ................
00000010: ea000005 00001ed0 ea000006 ea000006    ................
00000020: eafffffe eafffffe eafffffe e25ef004    ..............^.
00000030: e1a00000 eafffffe eafffffe eafffffe    ................
00000040: e3a0d9c2 e59f40c4 e1a0e00f e12fff14    .....@......../.
00000050: e59f20bc e892001a e1530004 34912004    . ........S.. .4
00000060: 34832004 3afffffb e28f2098 e8920018    . .4...:. ......
00000070: e3a02000 e1530004 34832004 3afffffc    . ....S.. .4...:
U-Boot> version

U-Boot 2014.07-00058-gb44bde2-dirty (Mar 15 2015 - 01:53:35)
arm-none-eabi-gcc (GNU Tools for ARM Embedded Processors) 4.9.3 20141119 (release) [ARM/embedded-4_9-branch revision 218278]
GNU ld (GNU Tools for ARM Embedded Processors) 2.24.0.20141128
U-Boot> usb
usb - USB sub-system

Usage:
usb start - start (scan) USB controller
usb reset - reset (rescan) USB controller
usb stop [f] - stop USB [f]=force stop
usb tree - show USB device tree
usb info [dev] - show available USB devices
usb test [dev] [port] [mode] - set USB 2.0 test mode
    (specify port 0 to indicate the device's upstream port)
    Available modes: J, K, S[E0_NAK], P[acket], F[orce_Enable]
usb storage - show details of USB storage devices
usb dev [dev] - show or set current USB storage device
usb part [dev] - print partition table of one or all USB storage    devices
usb read addr blk# cnt - read `cnt' blocks starting at block `blk#'
    to memory address `addr'
usb write addr blk# cnt - write `cnt' blocks starting at block `blk#'
    from memory address `addr'
U-Boot> usb info
USB is stopped. Please issue 'usb start' first.
U-Boot> usb start
(Re)start USB...
USB0:   scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
U-Boot> usb info
1: Hub,  USB Revision 1.10
 -  U-Boot Root Hub
 - Class: Hub
 - PacketSize: 8  Configurations: 1
 - Vendor: 0x0000  Product 0x0000 Version 0.0
   Configuration: 1
   - Interfaces: 1 Self Powered 0mA
     Interface: 0
     - Alternate Setting 0, Endpoints: 1
     - Class Hub
     - Endpoint 1 In Interrupt MaxPacket 2 Interval 255ms

U-Boot> usb tree
USB device tree:
  1  Hub (12 Mb/s, 0mA)
      U-Boot Root Hub

U-Boot> coninfo
List of available devices:
lcd      00000002 ..O
serial   80000003 SIO stdin stdout stderr
atmel_serial 00000003 .IO
U-Boot> chpart
Device nand0 not found!
U-Boot>