Skip to content

Instantly share code, notes, and snippets.

@halmartin
Created December 16, 2020 21:13
Show Gist options
  • Save halmartin/27c1245cf00aa2dd9bfaa16ddac3e98c to your computer and use it in GitHub Desktop.
Save halmartin/27c1245cf00aa2dd9bfaa16ddac3e98c to your computer and use it in GitHub Desktop.
Meraki MX80 wired-14-202005181203-G201ba9ed-rel-gazebo
U-Boot 2009.11-00043-gf4c39d3-serengeti_DEV_1.19.01 (Feb 15 2012 - 10:40:18)
CPU: AMCC PowerPC 460 APM86290 at 1000 MHz PLB=500 MHz
(SOC=1000 AXI=250 AHB=166 APB=83 EBC=100)
Internal PCI arbiter disabled
32 kB I-Cache 32 kB D-Cache
Board: Fullerene-2 - Meraki Fullerene Cloud Managed Router
I2C: ready
DRAM: -2 GB at 800MHz
Default enable MDIO for ETH0
Net: Init Atheros ...
ethaddr[1]: ethaddr not set!
eth0
NAND: 1024 MiB
*** Warning - bad CRC or NAND, using default environment
Set serverpath and run meraki_netboot to netboot
Hit any key to stop autoboot: 0
Creating 1 MTD partitions on "nand0":
0x000000240000-0x000040000000 : "mtd=2"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=2"
UBI: MTD device size: 1021 MiB
UBI: number of good PEBs: 8174
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 4
UBI: available PEBs: 3404
UBI: total number of reserved PEBs: 4770
UBI: number of PEBs reserved for bad PEB handling: 81
UBI: max/mean erase counter: 11/6
Volume part1 found at volume id 0
read 0 bytes from volume 0 to 800000(buf address)
Read [33675264] bytes
UBI: fixable bit-flip detected at PEB 5326
UBI: schedule PEB 5326 for scrubbing
setting meraki addr env fdt: 0x804000, kernel: 0x820000, ramdisk: 0xc00000
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 00820000 ...
Image Name: Linux-3.4.113
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 2447726 Bytes = 2.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 00c00000 ...
Image Name: Simple Ramdisk Image
Image Type: PowerPC Linux RAMDisk Image (lzma compressed)
Data Size: 16719915 Bytes = 15.9 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 00804000
Booting using the fdt blob at 0x804000
Uncompressing Kernel Image ... OK
Loading Ramdisk to 2f00d000, end 2ffff02b ... OK
[ 0.000000] Meraki: removing an additional 17MB for the crypto acceleration driver on MX80/MX90
[ 0.000000] New memory limit = 0x7df00000
[ 0.000000] Using Serengeti machine description
[ 0.000000] Linux version 3.4.113 ([email protected]) (gcc version 4.8.3 (GCC) ) #4 Thu May 28 18:15:30 PD
T 2020
[ 0.000000] Found initrd at 0xaf00d000:0xaffff02b
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00070000
[ 0.000000] Normal empty
[ 0.000000] HighMem 0x00070000 -> 0x0007df00
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0007df00
[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 511810
[ 0.000000] Kernel command line: root=/dev/ram console=ttyS0,57600 ubi.mtd=ubi MERAKI_BOARD=fullerene mtdoops.mtdd
ev=oops mem=0x7f000000
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Memory: 2024192k/2063360k available (4572k kernel code, 39168k reserved, 188k data, 259k bss, 180k ini
t)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffcf000..0xfffff000 : fixmap
[ 0.000000] * 0xffc00000..0xffe00000 : highmem PTEs
[ 0.000000] * 0xff200000..0xffc00000 : consistent mem
[ 0.000000] * 0xff200000..0xff200000 : early ioremap
[ 0.000000] * 0xf1000000..0xff200000 : vmalloc & ioremap
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] mpic: Setting up MPIC " MPIC " version 1.2 at ddf400000, max 1 CPUs
[ 0.000000] mpic: ISU size: 128, shift: 7, mask: 7f
[ 0.000000] mpic: Initializing for 128 sources
[ 0.000000] clocksource: timebase mult[800000] shift[23] registered
[ 0.000061] pid_max: default: 32768 minimum: 301
[ 0.000162] Mount-cache hash table entries: 512
[ 0.001911] devtmpfs: initialized
[ 0.002371] xor: measuring software checksum speed
[ 0.020074] 8regs : 747.000 MB/sec
[ 0.040083] 8regs_prefetch: 668.000 MB/sec
[ 0.060094] 32regs : 784.000 MB/sec
[ 0.080104] 32regs_prefetch: 712.000 MB/sec
[ 0.080111] xor: using function: 32regs (784.000 MB/sec)
[ 0.080214] NET: Registered protocol family 16
[ 0.081784] gpiochip_add: registered GPIOs 230 to 255 on device: /hbf/ahb/apb/gpio@fa0004000
[ 0.081995] gpiochip_add: registered GPIOs 214 to 229 on device: /hbf/ipp@ddd8b0000
[ 0.082022] APM863xx detected (0x4002000A)
[ 0.082075] APM SoC APM86xxx iPP CPU0 Hard CPU0
[ 0.082473] PCI: Probing PCI hardware
[ 0.092977] bio: create slab <bio-0> at 0
[ 0.160232] raid6: int32x1 258 MB/s
[ 0.228333] raid6: int32x2 347 MB/s
[ 0.296488] raid6: int32x4 379 MB/s
[ 0.364397] raid6: int32x8 246 MB/s
[ 0.364403] raid6: using algorithm int32x4 (379 MB/s)
[ 0.365286] SCSI subsystem initialized
[ 0.365855] usbcore: registered new interface driver usbfs
[ 0.366096] usbcore: registered new interface driver hub
[ 0.366266] usbcore: registered new device driver usb
[ 0.367485] Switching to clocksource timebase
[ 0.369555] NET: Registered protocol family 2
[ 0.375002] IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.376132] TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.382656] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.383420] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.383429] TCP: reno registered
[ 0.383441] UDP hash table entries: 1024 (order: 2, 16384 bytes)
[ 0.383500] UDP-Lite hash table entries: 1024 (order: 2, 16384 bytes)
[ 0.383804] NET: Registered protocol family 1
[ 0.383986] Trying to unpack rootfs image as initramfs...
[ 11.783432] Freeing initrd memory: 16332k freed
[ 11.786487] qm_cfg: 1
[ 11.810676] APM QM-TM Driver v0.1
[ 11.930662] highmem bounce pool size: 64 pages
[ 12.200461] msgmni has been set to 3539
[ 12.213614] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 12.213633] io scheduler noop registered
[ 12.213639] io scheduler deadline registered (default)
[ 12.215804] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 12.250798] fa0000000.serial: ttyS0 at MMIO 0xfa0000000 (irq = 39) is a 16550
[ 13.063351] console [ttyS0] enabled
[ 13.078570] fa0001000.serial: ttyS1 at MMIO 0xfa0001000 (irq = 40) is a 16550
[ 13.101094] fa0007000.serial: ttyS2 at MMIO 0xfa0007000 (irq = 41) is a 16550
[ 13.123667] fa0008000.serial: ttyS3 at MMIO 0xfa0008000 (irq = 42) is a 16550
[ 13.146071] Trying to register dev faulty etc
[ 13.288715] brd: module loaded
[ 13.366889] loop: module loaded
[ 13.405011] mpt2sas version 12.100.00.00 loaded
[ 13.438394] ahci-sata-of 500000000.sata: version 3.0
[ 13.448419] ahci-sata-of 500000000.sata: forcing port_map 0x0 -> 0x1
[ 13.470187] ahci-sata-of 500000000.sata: AHCI 0001.0300 32 slots 2 ports 3 Gbps 0x1 impl of mode
[ 13.487685] ahci-sata-of 500000000.sata: flags: 64bit ncq sntf pm led clo only pmp pio slum part ccc apst
[ 13.536232] scsi0 : ahci_of
[ 13.549984] scsi1 : ahci_of
[ 13.561901] ata1: SATA max UDMA/133 mmio [io 0x81ff26e700000080-0x0000 disabled] port 0x100 irq 44
[ 13.579947] ata2: DUMMY
[ 13.625335] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xa3 (Micron NAND 1GiB 1,8V 8-bit)
[ 13.643046] Scanning device for bad blocks
[ 15.609333] 5 ofpart partitions found on MTD device fa0140000.ufc.nand
[ 15.622360] Creating 5 MTD partitions on "fa0140000.ufc.nand":
[ 15.633980] 0x000000000000-0x000000100000 : "firmware"
[ 15.655146] 0x000000100000-0x000000200000 : "environment"
[ 15.682437] 0x000000200000-0x000000240000 : "oops-old"
[ 15.709248] 0x000000240000-0x000040000000 : "ubi"
[ 15.736092] 0x000000000000-0x000040000000 : "all"
[ 15.775027] UBI: attaching mtd3 to ubi0
[ 15.782699] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 15.795171] UBI: logical eraseblock size: 129024 bytes
[ 15.805915] UBI: smallest flash I/O unit: 2048
[ 15.815275] UBI: sub-page size: 512
[ 15.824464] UBI: VID header offset: 512 (aligned 512)
[ 15.836072] UBI: data offset: 2048
[ 17.307774] ata1: Signature Update detected @ 0 msecs 0x00000101 1
[ 17.496129] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 17.520757] ata1.00: ATA-8: WDC WD10EZRX-00L4HB0, 01.01A01, max UDMA/133
[ 17.534108] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 17.577546] ata1.00: configured for UDMA/133
[ 17.586360] scsi 0:0:0:0: Direct-Access ATA WDC WD10EZRX-00L 01.0 PQ: 0 ANSI: 5
[ 17.632612] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 17.647888] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 17.663799] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 17.694160] sd 0:0:0:0: [sda] Write Protect is off
[ 17.716124] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 18.384007] sda: sda1
[ 18.398641] sd 0:0:0:0: [sda] Attached SCSI disk
[ 21.578358] UBI: max. sequence number: 42518
[ 21.630225] UBI: attached mtd3 to ubi0
[ 21.637722] UBI: MTD device name: "ubi"
[ 21.647255] UBI: MTD device size: 1021 MiB
[ 21.657307] UBI: number of good PEBs: 8174
[ 21.666667] UBI: number of bad PEBs: 0
[ 21.675509] UBI: number of corrupted PEBs: 0
[ 21.684349] UBI: max. allowed volumes: 128
[ 21.693537] UBI: wear-leveling threshold: 4096
[ 21.702895] UBI: number of internal volumes: 1
[ 21.711736] UBI: number of user volumes: 4
[ 21.720577] UBI: available PEBs: 3323
[ 21.729935] UBI: total number of reserved PEBs: 4851
[ 21.739813] UBI: number of PEBs reserved for bad PEB handling: 162
[ 21.752112] UBI: max/mean erase counter: 11/6
[ 21.760780] UBI: image sequence number: 2076992182
[ 21.770584] UBI: background thread "ubi_bgt0d" started, PID 683
[ 21.870120] PPC 4xx OCP EMAC driver, version 3.54
[ 21.895848] PPP generic driver version 2.4.2
[ 21.914327] PPP BSD Compression module registered
[ 21.923728] PPP Deflate Compression module registered
[ 21.933781] NET: Registered protocol family 24
[ 21.950295] usbcore: registered new interface driver cdc_ether
[ 21.962300] usbcore: registered new interface driver cdc_eem
[ 21.981207] usbcore: registered new interface driver cdc_subset
[ 21.993416] usbcore: registered new interface driver cdc_ncm
[ 22.004706] Fusion MPT base driver 3.04.20
[ 22.012856] Copyright (c) 1999-2008 LSI Corporation
[ 22.022590] Fusion MPT SAS Host driver 3.04.20
[ 22.045539] usbcore: registered new interface driver cdc_acm
[ 22.056841] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 22.082729] usbcore: registered new interface driver usbserial
[ 22.094375] usbserial: USB Serial Driver core
[ 22.110682] usbcore: registered new interface driver option
[ 22.122145] USB Serial support registered for GSM modem (1-port)
[ 22.141734] usbcore: registered new interface driver qcserial
[ 22.153546] USB Serial support registered for Qualcomm USB modem
[ 22.173145] usbcore: registered new interface driver sierra
[ 22.184609] USB Serial support registered for Sierra USB modem
[ 22.206295] dummy_hcd dummy_hcd: USB Host+Gadget Emulator, driver 02 May 2005
[ 22.220548] dummy_hcd dummy_hcd: Dummy host controller
[ 22.236966] dummy_hcd dummy_hcd: new USB bus registered, assigned bus number 1
[ 22.251476] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 22.264998] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 22.279374] usb usb1: Product: Dummy host controller
[ 22.289256] usb usb1: Manufacturer: Linux 3.4.113 dummy_hcd
[ 22.300345] usb usb1: SerialNumber: dummy_hcd
[ 22.315352] hub 1-0:1.0: USB hub found
[ 22.322870] hub 1-0:1.0: 1 port detected
[ 22.347389] input: gpio_keys_polled.4 as /devices/hbf.0/gpio_keys_polled.4/input/input0
[ 22.379450] i2c /dev entries driver
[ 22.407245] gpiochip_add: registered GPIOs 190 to 213 on device: tca6424
[ 22.420632] EVERYTHNIG WENT GREAT
[ 22.445950] EVERYTHNIG WENT GREAT
[ 22.464051] booke_wdt: powerpc book-e watchdog driver loaded
[ 22.480707] md: linear personality registered for level -1
[ 22.491660] md: raid0 personality registered for level 0
[ 22.502232] md: raid1 personality registered for level 1
[ 22.512803] md: raid10 personality registered for level 10
[ 22.523720] md: raid6 personality registered for level 6
[ 22.534290] md: raid5 personality registered for level 5
[ 22.544861] md: raid4 personality registered for level 4
[ 22.569739] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected]
[ 22.592543] device-mapper: multipath: version 1.3.2 loaded
[ 22.603496] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 22.616489] device-mapper: multipath queue-length: version 0.1.0 loaded
[ 22.629653] device-mapper: multipath service-time: version 0.2.0 loaded
[ 22.646925] device-mapper: dm-log-userspace: version 1.1.0 loaded
[ 22.714045] APMSEC: APM 862xx SoC security accelerator driver v0.1
[ 22.736867] usbcore: registered new interface driver usbhid
[ 22.747995] usbhid: USB HID core driver
[ 22.755634] oprofile: using timer interrupt.
[ 22.764419] TCP: cubic registered
[ 22.771027] Initializing XFRM netlink socket
[ 22.779538] NET: Registered protocol family 17
[ 22.788410] NET: Registered protocol family 15
[ 22.797259] L2TP core driver, V2.0
[ 22.804049] PPPoL2TP kernel driver, V2.0
[ 22.811853] 8021q: 802.1Q VLAN Support v1.8
[ 22.841027] /mnt/jenkins/workspace/router/prod-signing/wired-14-5/linux-3.4/drivers/rtc/hctosys.c: unable to open
rtc device (rtc0)
[ 22.864733] devtmpfs: mounted
[ 22.873280] Freeing unused kernel memory: 180k freed
[ 22.891039] Made it into bootsh: May 28 2020 18:08:47
[ 22.901383] bootsh build wired-14-202005181203-G201ba9ed-rel-gazebo
[ 23.012121] UBIFS: recovery needed
[ 25.460844] UBIFS: recovery completed
[ 25.468159] UBIFS: mounted UBI device 0, volume 3, name "storage"
[ 25.480291] UBIFS: file system size: 535062528 bytes (522522 KiB, 510 MiB, 4147 LEBs)
[ 25.496223] UBIFS: journal size: 26836992 bytes (26208 KiB, 25 MiB, 208 LEBs)
[ 25.511463] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 25.523070] UBIFS: default compressor: lzo
[ 25.531221] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
In manufacturing: FALSE
In rma mode: FALSE
[ 25.687406] init started: BusyBox v1.25.1 (2020-05-28 15:31:19 PDT)
[ 25.723163] sh: Maggot: unknown operand
WARNING! THIS CONSOLE IS LOGGED! UNAUTHORIZED ACCESS FORBIDDEN!
<Meraki> [ 25.824305] Sat Jan 1 00:00:00 UTC 2000
[ 26.108818] sysctl: error: 'kernel.softlockup_panic' is an unknown key
[ 26.121994] sysctl: error: 'kernel.watchdog_thresh' is an unknown key
[ 26.134985] sysctl: error: 'vm.extfrag_threshold' is an unknown key
[ 26.177281] sysctl: The scan_unevictable_pages sysctl/node-interface has been disabled for lack of a legitimate us
e case. If you have one, please send an email to [email protected].
[ 26.499839] rsyslogd: imchardevice: cannot open char device (/dev/click_to_rsyslog): No such file or directory.
[ 26.520106] rsyslogd: activation of module imchardevice failed [v8.36.0 try http://www.rsyslog.com/e/2145 ]
[ 26.675746] [2000-01-01 00:00:00.851] sysctl -w vm.panic_on_oom=2
[ 26.692042] vm.panic_on_oom = 2
[ 26.846886] click: starting router thread pid 1142 (afa72300)
[ 26.934975] elts_meraki: module license 'unspecified' taints kernel.
[ 27.257193] Single synchronous check for reset
[ 27.330056] GobiNet: 2013-10-08/NTGR_2.21
[ 27.366116] usbcore: registered new interface driver GobiNet
[ 27.449962] usbcore: registered new interface driver GobiSerial
[ 27.495589] USB Serial support registered for GobiSerial
[ 27.506188] GobiSerial: 2013-10-08/NTGR_2.12:GobiSerial
[ 27.547274] dwc_otg: version 2.60a 22-NOV-2006
[ 27.557429] Synopsis DWC USB-OTG ID 0x4f54291a
[ 27.766471] dwc_otg: Using DMA mode
[ 27.773425] usb-otg fa0100000.usb: DWC OTG Controller
[ 27.792297] usb-otg fa0100000.usb: new USB bus registered, assigned bus number 2
[ 27.807086] usb-otg fa0100000.usb: irq 79, io mem 0xfa0100000
[ 27.818637] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 27.832163] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 27.846544] usb usb2: Product: DWC OTG Controller
[ 27.855907] usb usb2: Manufacturer: Linux 3.4.113 dwc_otg_hcd
[ 27.867342] usb usb2: SerialNumber: dwc_otg_hcd
[ 27.887094] hub 2-0:1.0: USB hub found
[ 27.894614] hub 2-0:1.0: 1 port detected
[ 27.912825] dwc_otg: Dedicated Tx FIFOs mode
[ 27.976069] dwc_otg: version 2.60a 22-NOV-2006
[ 28.312256]
[ 28.322094] boot 56 build wired-14-202005181203-G201ba9ed-rel-gazebo board wired-powerpc mac 88:15:44:BA:DB:AD
[ 28.344625] /usr/bin/snort-version
[ 28.359347] Module: proclikefs .text=0xf10d5000 .data= .bss=0xf10d5d80
[ 28.359358] Module: merakiclick .text=0xf28ed000 .data=0xf2a02af0 .bss=0xf2a02f40
[ 28.359362] Module: elts_meraki .text=0xf308b000 .data=0xf33c895c .bss=0xf33caf90
[ 28.359366] Module: GobiNet .text=0xf10f1000 .data=0xf10fa220 .bss=0xf10fa464
[ 28.359370] Module: GobiSerial .text=0xf153c000 .data=0xf153d098 .bss=0xf153d54c
[ 28.359375] Module: apm_otg .text=0xf2581000 .data=0xf25921c0 .bss=0xf25926e0
[ 28.359379] Module: dwc_otg .text=0xf3560000 .data=0xf35729e8 .bss=0xf3572f0c
[ 28.359383] Module: scsi_wait_scan .text=0xf10fd000 .data= .bss=
[ 28.510097] ramoops: platform device not found, using module parameters
[ 28.585477] phram: phram-oops device: 0x100000 at 0x7df00000
[ 28.662520] not unlocked
[ 31.139585] kjournald starting. Commit interval 5 seconds
[ 31.254638] EXT3-fs (sda1): warning: maximal mount count reached, running e2fsck is recommended
[ 31.470684] EXT3-fs (sda1): using internal journal
[ 31.569855] EXT3-fs (sda1): recovery complete
[ 31.578572] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 32.420583] chatter: RealRFC4305AEAD initialized with driver authenc(apm-hmac-sha1,apm-ctr-aes)
[ 32.438319] chatter: RealRFC4305AEAD initialized with driver authenc(apm-hmac-sha1,apm-ctr-aes)
[ 32.455745] chatter: RealRFC4305AEAD initialized with driver authenc(apm-hmac-sha1,apm-ctr-aes)
[ 32.476055] chatter: RealRFC4305AEAD initialized with driver authenc(apm-hmac-sha1,apm-ctr-aes)
[ 32.493475] chatter: RealRFC4305AEAD initialized with driver authenc(apm-hmac-sha1,apm-ctr-aes)
[ 32.511065] chatter: RealRFC4305AEAD initialized with driver authenc(apm-hmac-sha1,apm-ctr-aes)
[ 32.528468] chatter: RealRFC4305AEAD initialized with driver authenc(apm-hmac-sha1,apm-ctr-aes)
[ 32.638323] chatter: to_bird :: ToHost: device 'bird' went down
[ 32.664552] chatter: to_bird :: ToHost: device 'bird' came up
[ 32.693999] device sw0 entered promiscuous mode
[ 32.703726] changing MTU from 1500 to 1508
[ 32.712168] sw0 Link is up with speed 1000 Mbps
[ 32.730608] device sw1 entered promiscuous mode
[ 32.740187] changing MTU from 1500 to 1508
[ 32.748852] sw1 Link is up with speed 1000 Mbps
[ 44.109650] chatter: RealRFC4305AEAD initialized with driver authenc(hmac(sha256-generic),apm-ctr-aes)
[ 44.128307] chatter: RealRFC4305AEAD initialized with driver authenc(apm-hmac-sha1,apm-ctr-aes)
[ 44.530039] In write handler 'run' for 'nat/set_filters :: Script':
[ 44.542587] While calling 'nat/from_inet_filter.config deny all':
[ 44.555073] pattern 0: warning: meaning of 'deny' has changed (now it means 'drop')
[ 45.234147]
[ 45.234153] !!!!! {/usr/bin/wired_brain} open failed for "/click/router_hw_intf/bounce_enabled", error: No such fi
le or directory
[ 46.418566]
[ 46.418571] !!!!! {/usr/bin/config_updater} failsafe_mode "value='0' state='0' bootloop='0' ver='1' " ""
[ 46.622046] chatter: _to_linux_test_client :: ToHost: device 'test_client' went down
[ 47.158831] In write handler 'run' for 'nat/set_filters :: Script':
[ 47.171379] While calling 'nat/from_inet_filter.config deny all':
[ 47.183858] pattern 0: warning: meaning of 'deny' has changed (now it means 'drop')
[ 48.233193] chatter: big_acl :: BigACL: skipping undersized restore buffer (buf size: 0)
[ 116.872534] device snort0 entered promiscuous mode
[ 182.474955] chatter: apr0v1_port/dev_queue/unshaped_control_q :: Queue: overflow
[ 182.489743] chatter: apr0v2_port/dev_queue/unshaped_control_q :: Queue: overflow
[ 182.504495] chatter: apr0v3_port/dev_queue/unshaped_control_q :: Queue: overflow
[ 182.519245] chatter: apr0v4_port/dev_queue/unshaped_control_q :: Queue: overflow
[ 182.534001] chatter: apr1v1_port/dev_queue/unshaped_control_q :: Queue: overflow
[ 182.548755] chatter: apr1v2_port/dev_queue/unshaped_control_q :: Queue: overflow
[ 182.563507] chatter: apr1v3_port/dev_queue/unshaped_control_q :: Queue: overflow
[ 182.578261] chatter: apr1v4_port/dev_queue/unshaped_control_q :: Queue: overflow
<Meraki>
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment