cleaned-up 5.15 PR kernel

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.15.71 (perus@ub2204) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.3.0 r20513-a99707d14c) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 SMP Thu Oct 6 16:00:19 2022
[    0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: Netgear Nighthawk X4S R7800
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000042000000-0x000000005fffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000042000000-0x000000005fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000042000000-0x000000005fffffff]
[    0.000000] percpu: Embedded 12 pages/cpu s16396 r8192 d24564 u49152
[    0.000000] pcpu-alloc: s16396 r8192 d24564 u49152 alloc=12*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 121800
[    0.000000] Kernel command line: 
[    0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 473140K/491520K available (7220K kernel code, 615K rwdata, 1756K rodata, 1024K init, 236K bss, 18380K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[    0.000001] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[    0.000025] Switching to timer-based delay loop, resolution 160ns
[    0.000345] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[    0.000382] pid_max: default: 32768 minimum: 301
[    0.000646] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.000675] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.001810] CPU: Testing write buffer coherency: ok
[    0.002140] qcom_scm: convention: smc legacy
[    0.003459] Setting up static identity map for 0x42300000 - 0x42300060
[    0.003652] rcu: Hierarchical SRCU implementation.
[    0.003979] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.004245] smp: Bringing up secondary CPUs ...
[    0.006227] smp: Brought up 1 node, 2 CPUs
[    0.006259] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[    0.006280] CPU: All CPU(s) started in SVC mode.
[    0.017156] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[    0.017316] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.017355] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.017519] pinctrl core: initialized pinctrl subsystem
[    0.019309] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.019642] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.021069] thermal_sys: Registered thermal governor 'step_wise'
[    0.023072] cpuidle: using governor ladder
[    0.023152] cpuidle: using governor menu
[    0.041868] qcom_rpm 108000.rpm: RPM firmware 3.0.16777364
[    0.074600] qcom_rpm_reg 108000.rpm:regulators: invalid frequency 500000
[    0.074629] qcom_rpm_reg 108000.rpm:regulators: driver callback failed to parse DT for regulator s1a
[    0.074824] s1a: supplied by regulator-dummy
[    0.074988] qcom_rpm_reg 108000.rpm:regulators: invalid frequency 500000
[    0.075013] qcom_rpm_reg 108000.rpm:regulators: driver callback failed to parse DT for regulator s1b
[    0.075181] s1b: supplied by regulator-dummy
[    0.075323] qcom_rpm_reg 108000.rpm:regulators: invalid frequency 500000
[    0.075343] qcom_rpm_reg 108000.rpm:regulators: driver callback failed to parse DT for regulator s2a
[    0.075521] s2a: supplied by regulator-dummy
[    0.075674] qcom_rpm_reg 108000.rpm:regulators: invalid frequency 500000
[    0.075695] qcom_rpm_reg 108000.rpm:regulators: driver callback failed to parse DT for regulator s2b
[    0.075874] s2b: supplied by regulator-dummy
[    0.076428] usbcore: registered new interface driver usbfs
[    0.076499] usbcore: registered new interface driver hub
[    0.076564] usbcore: registered new device driver usb
[    0.076622] pps_core: LinuxPPS API ver. 1 registered
[    0.076637] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[    0.076673] PTP clock support registered
[    0.078677] clocksource: Switched to clocksource dg_timer
[    0.079624] NET: Registered PF_INET protocol family
[    0.079830] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.080611] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.080650] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.080677] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.080721] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.080780] TCP: Hash tables configured (established 4096 bind 4096)
[    0.080864] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.080899] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.081148] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.081202] PCI: CLS 0 bytes, default 64
[    0.082087] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    0.087665] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.087687] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.249276] qcom-pcie 1b500000.pci: supply vdda not found, using dummy regulator
[    0.249500] qcom-pcie 1b500000.pci: supply vdda_phy not found, using dummy regulator
[    0.249622] qcom-pcie 1b500000.pci: supply vdda_refclk not found, using dummy regulator
[    0.249869] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
[    0.249916] qcom-pcie 1b500000.pci: Parsing ranges property...
[    0.249960] qcom-pcie 1b500000.pci:       IO 0x000fe00000..0x000fe0ffff -> 0x000fe00000
[    0.250005] qcom-pcie 1b500000.pci:      MEM 0x0008000000..0x000fdfffff -> 0x0008000000
[    0.371913] qcom-pcie 1b500000.pci: iATU unroll: disabled
[    0.371935] qcom-pcie 1b500000.pci: Detected iATU regions: 8 outbound, 8 inbound
[    0.474692] qcom-pcie 1b500000.pci: Link up
[    0.474836] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[    0.474858] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.474885] pci_bus 0000:00: root bus resource [io  0x0000-0xffff] (bus address [0xfe00000-0xfe0ffff])
[    0.474908] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[    0.474931] pci_bus 0000:00: scanning bus
[    0.474986] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[    0.475129] pci 0000:00:00.0: supports D1
[    0.475148] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    0.475171] pci 0000:00:00.0: PME# disabled
[    0.478734] pci_bus 0000:00: fixups for bus
[    0.478761] PCI: bus0: Fast back to back transfers disabled
[    0.478784] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[    0.479010] pci_bus 0000:01: scanning bus
[    0.479221] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000
[    0.479404] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.480209] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.480252] pci 0000:01:00.0: PME# disabled
[    0.483949] pci_bus 0000:01: fixups for bus
[    0.484005] PCI: bus1: Fast back to back transfers disabled
[    0.484026] pci_bus 0000:01: bus scan returning with max=01
[    0.484046] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[    0.484067] pci_bus 0000:00: bus scan returning with max=ff
[    0.484099] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[    0.484128] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[    0.484229] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    0.484255] pci 0000:00:00.0:   bridge window [mem 0x08000000-0x081fffff]
[    0.484442] pcieport 0000:00:00.0: assign IRQ: got 43
[    0.484553] qcom-pcie 1b500000.pci: msi#0 address_hi 0x0 address_lo 0x4363fe98
[    0.485501] pcieport 0000:00:00.0: AER: enabled with IRQ 44
[    0.485599] pcieport 0000:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
[    0.485619] pcieport 0000:00:00.0: saving config space at offset 0x4 (reading 0x100547)
[    0.485634] pcieport 0000:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
[    0.485649] pcieport 0000:00:00.0: saving config space at offset 0xc (reading 0x10010)
[    0.485663] pcieport 0000:00:00.0: saving config space at offset 0x10 (reading 0x0)
[    0.485678] pcieport 0000:00:00.0: saving config space at offset 0x14 (reading 0x0)
[    0.485694] pcieport 0000:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
[    0.485708] pcieport 0000:00:00.0: saving config space at offset 0x1c (reading 0xf0)
[    0.485723] pcieport 0000:00:00.0: saving config space at offset 0x20 (reading 0x8100800)
[    0.485740] pcieport 0000:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
[    0.485754] pcieport 0000:00:00.0: saving config space at offset 0x28 (reading 0x0)
[    0.485768] pcieport 0000:00:00.0: saving config space at offset 0x2c (reading 0x0)
[    0.485782] pcieport 0000:00:00.0: saving config space at offset 0x30 (reading 0x0)
[    0.485797] pcieport 0000:00:00.0: saving config space at offset 0x34 (reading 0x40)
[    0.485811] pcieport 0000:00:00.0: saving config space at offset 0x38 (reading 0x0)
[    0.485826] pcieport 0000:00:00.0: saving config space at offset 0x3c (reading 0x3012b)
[    0.486467] qcom-pcie 1b700000.pci: supply vdda not found, using dummy regulator
[    0.486675] qcom-pcie 1b700000.pci: supply vdda_phy not found, using dummy regulator
[    0.486782] qcom-pcie 1b700000.pci: supply vdda_refclk not found, using dummy regulator
[    0.487047] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
[    0.487090] qcom-pcie 1b700000.pci: Parsing ranges property...
[    0.487133] qcom-pcie 1b700000.pci:       IO 0x0031e00000..0x0031e0ffff -> 0x0031e00000
[    0.487181] qcom-pcie 1b700000.pci:      MEM 0x002e000000..0x0031dfffff -> 0x002e000000
[    0.613554] qcom-pcie 1b700000.pci: iATU unroll: disabled
[    0.613576] qcom-pcie 1b700000.pci: Detected iATU regions: 8 outbound, 8 inbound
[    0.716334] qcom-pcie 1b700000.pci: Link up
[    0.716475] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[    0.716497] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.716522] pci_bus 0001:00: root bus resource [io  0x10000-0x1ffff] (bus address [0x31e00000-0x31e0ffff])
[    0.716543] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[    0.716564] pci_bus 0001:00: scanning bus
[    0.716613] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[    0.716742] pci 0001:00:00.0: supports D1
[    0.716759] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[    0.716778] pci 0001:00:00.0: PME# disabled
[    0.720409] pci_bus 0001:00: fixups for bus
[    0.720435] PCI: bus0: Fast back to back transfers disabled
[    0.720455] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[    0.720589] pci_bus 0001:01: scanning bus
[    0.720812] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000
[    0.721009] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.721885] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[    0.721928] pci 0001:01:00.0: PME# disabled
[    0.722167] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0001:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[    0.725660] pci_bus 0001:01: fixups for bus
[    0.725720] PCI: bus1: Fast back to back transfers disabled
[    0.725739] pci_bus 0001:01: bus scan returning with max=01
[    0.725757] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[    0.725778] pci_bus 0001:00: bus scan returning with max=ff
[    0.725805] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[    0.725834] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[    0.725937] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[    0.725961] pci 0001:00:00.0:   bridge window [mem 0x2e000000-0x2e1fffff]
[    0.726141] pcieport 0001:00:00.0: assign IRQ: got 45
[    0.726254] qcom-pcie 1b700000.pci: msi#0 address_hi 0x0 address_lo 0x4378ae98
[    0.727072] pcieport 0001:00:00.0: AER: enabled with IRQ 46
[    0.727169] pcieport 0001:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
[    0.727188] pcieport 0001:00:00.0: saving config space at offset 0x4 (reading 0x100547)
[    0.727204] pcieport 0001:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
[    0.727219] pcieport 0001:00:00.0: saving config space at offset 0xc (reading 0x10010)
[    0.727233] pcieport 0001:00:00.0: saving config space at offset 0x10 (reading 0x0)
[    0.727248] pcieport 0001:00:00.0: saving config space at offset 0x14 (reading 0x0)
[    0.727262] pcieport 0001:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
[    0.727276] pcieport 0001:00:00.0: saving config space at offset 0x1c (reading 0xf0)
[    0.727290] pcieport 0001:00:00.0: saving config space at offset 0x20 (reading 0x2e102e00)
[    0.727304] pcieport 0001:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
[    0.727319] pcieport 0001:00:00.0: saving config space at offset 0x28 (reading 0x0)
[    0.727334] pcieport 0001:00:00.0: saving config space at offset 0x2c (reading 0x0)
[    0.727348] pcieport 0001:00:00.0: saving config space at offset 0x30 (reading 0x0)
[    0.727363] pcieport 0001:00:00.0: saving config space at offset 0x34 (reading 0x40)
[    0.727379] pcieport 0001:00:00.0: saving config space at offset 0x38 (reading 0x0)
[    0.727393] pcieport 0001:00:00.0: saving config space at offset 0x3c (reading 0x3012d)
[    0.730683] krait-cc soc:clock-controller: CPU0 @ 800000 KHz
[    0.730711] krait-cc soc:clock-controller: CPU1 @ PXO rate. Forcing new rate.
[    0.730857] krait-cc soc:clock-controller: CPU1 @ 384000 KHz
[    0.730877] krait-cc soc:clock-controller: L2 @ PXO rate. Forcing new rate.
[    0.731084] krait-cc soc:clock-controller: L2 @ 384000 KHz
[    0.734961] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[    0.736712] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.737415] msm_serial 16340000.serial: msm_serial: detected port #0
[    0.737468] msm_serial 16340000.serial: uartclk = 7372800
[    0.737536] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 47, base_baud = 460800) is a MSM
[    0.737577] msm_serial: console setup on port #0
[    1.698890] printk: console [ttyMSM0] enabled
[    1.704100] msm_serial: driver initialized
[    1.712718] loop: module loaded
[    1.714063] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xa1
[    1.715023] nand: Micron MT29F1G08ABBEAH4
[    1.721692] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.725616] 8 fixed-partitions partitions found on MTD device qcom_nand.0
[    1.733103] OF: Bad cell count for /soc/nand-controller@1ac00000/nand@0/partitions
[    1.739988] OF: Bad cell count for /soc/nand-controller@1ac00000/nand@0/partitions
[    1.747936] Creating 8 MTD partitions on "qcom_nand.0":
[    1.754934] 0x000000000000-0x000000c80000 : "qcadata"
[    1.778304] 0x000000c80000-0x000001180000 : "APPSBL"
[    1.785971] 0x000001180000-0x000001200000 : "APPSBLENV"
[    1.787168] 0x000001200000-0x000001340000 : "art"
[    1.792341] 0x000001340000-0x000001480000 : "artbak"
[    1.797053] 0x000001480000-0x000001880000 : "kernel"
[    1.806112] 0x000001880000-0x000007900000 : "ubi"
[    1.943896] 0x000007900000-0x000008000000 : "reserve"
[    1.975659] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii
[    2.815317] ar8327: qca,phy-rgmii-en is not specified
[    2.816312] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
[    2.819457] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
[    2.827224] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[    2.833482] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[    2.839513] ipq806x-gmac-dwmac 37200000.ethernet: 	DWMAC1000
[    2.846874] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[    2.852790] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[    2.860498] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[    2.868311] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[    2.874202] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[    2.881576] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[    2.888279] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[    2.895915] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[    2.902944] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    2.911369] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
[    2.917711] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
[    2.925131] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[    2.931650] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[    2.937680] ipq806x-gmac-dwmac 37400000.ethernet: 	DWMAC1000
[    2.945227] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[    2.951025] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[    2.958678] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[    2.966661] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[    2.972484] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[    2.979866] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[    2.986543] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[    2.994164] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[    3.001192] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    3.009626] i2c_dev: i2c /dev entries driver
[    3.020304] sdhci: Secure Digital Host Controller Interface driver
[    3.020341] sdhci: Copyright(c) Pierre Ossman
[    3.026206] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.036881] NET: Registered PF_INET6 protocol family
[    3.039029] Segment Routing with IPv6
[    3.041362] In-situ OAM (IOAM) with IPv6
[    3.044982] NET: Registered PF_PACKET protocol family
[    3.049252] 8021q: 802.1Q VLAN Support v1.8
[    3.053861] Registering SWP/SWPB emulation handler
[    3.089116] thermal thermal_zone0: failed to read out thermal zone (-110)
[    3.098411] UBI: auto-attach mtd6
[    3.098454] ubi0: attaching mtd6
[    3.259196] random: crng init done
[    4.104494] ubi0: scanning is finished
[    4.119183] ubi0: attached mtd6 (name "ubi", size 96 MiB)
[    4.119233] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    4.123580] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    4.130433] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    4.137208] ubi0: good PEBs: 772, bad PEBs: 0, corrupted PEBs: 0
[    4.144043] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    4.150320] ubi0: max/mean erase counter: 4/1, WL threshold: 4096, image sequence number: 1664128758
[    4.157264] ubi0: available PEBs: 0, total reserved PEBs: 772, PEBs reserved for bad PEB handling: 20
[    4.167335] ubi0: background thread "ubi_bgt0d" started, PID 95
[    4.176437] block ubiblock0_0: created from ubi0:0(rootfs)
[    4.181492] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    4.193019] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    4.194177] Freeing unused kernel image (initmem) memory: 1024K
[    4.239301] Run /sbin/init as init process
[    4.239328]   with arguments:
[    4.239336]     /sbin/init
[    4.239344]   with environment:
[    4.239351]     HOME=/
[    4.239358]     TERM=linux
[    4.564036] init: Console is alive
[    4.564328] init: - watchdog -
[    4.566483] init: Watchdog has previously reset the system
[    6.836474] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    7.010279] pstore: Using crash dump compression: deflate
[    7.010329] pstore: Registered ramoops as persistent store backend
[    7.014671] ramoops: using 0x40000@0x42100000, ecc: 0
[    7.026164] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.035370] SCSI subsystem initialized
[    7.045306] libata version 3.00 loaded.
[    7.050506] ahci 29000000.sata: supply ahci not found, using dummy regulator
[    7.050802] ahci 29000000.sata: supply phy not found, using dummy regulator
[    7.056906] ahci 29000000.sata: supply target not found, using dummy regulator
[    7.066852] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
[    7.070800] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[    7.076088] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst 
[    7.085862] scsi host0: ahci
[    7.093447] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 32
[    7.421445] ata1: SATA link down (SStatus 0 SControl 300)
[    7.426430] ehci-fsl: Freescale EHCI Host controller driver
[    7.427978] ehci-platform: EHCI generic platform driver
[    7.441448] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.442715] ohci-platform: OHCI generic platform driver
[    7.589414] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    7.589486] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    7.594084] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000002002010010
[    7.601516] xhci-hcd xhci-hcd.0.auto: irq 51, io mem 0x10000000
[    7.611111] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    7.616649] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    7.622282] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[    7.630656] hub 1-0:1.0: USB hub found
[    7.636388] hub 1-0:1.0: 1 port detected
[    7.642432] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    7.644824] hub 2-0:1.0: USB hub found
[    7.653593] hub 2-0:1.0: 1 port detected
[    7.656302] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    7.659972] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[    7.665360] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000002002010010
[    7.672877] xhci-hcd xhci-hcd.1.auto: irq 52, io mem 0x11000000
[    7.682431] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    7.688003] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[    7.693636] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[    7.702230] hub 3-0:1.0: USB hub found
[    7.707888] hub 3-0:1.0: 1 port detected
[    7.714273] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    7.716351] hub 4-0:1.0: USB hub found
[    7.723776] hub 4-0:1.0: 1 port detected
[    7.737164] usbcore: registered new interface driver usb-storage
[    7.737501] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    7.744989] init: - preinit -
[   10.110606] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[   10.112800] dwmac1000: Master AXI performs any burst length
[   10.117882] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[   10.133315] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[   10.133525] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[   10.190722] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[   10.191888] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[   10.198863] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   15.532402] mount_root: loading kmods from internal overlay
[   15.584684] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   15.590447] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   15.754474] UBIFS (ubi0:1): Mounting in unauthenticated mode
[   15.759254] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 208
[   15.903231] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   15.903291] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   15.910181] UBIFS (ubi0:1): FS size: 84566016 bytes (80 MiB, 666 LEBs), max 677 LEBs, journal size 4190208 bytes (3 MiB, 33 LEBs)
[   15.920073] UBIFS (ubi0:1): reserved for root: 3994261 bytes (3900 KiB)
[   15.931676] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 51812F38-598C-4EC2-899F-926D4787294D, small LPT model
[   15.940536] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   15.949827] block: unable to load configuration (fstab: Entry not found)
[   15.956405] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[   15.963492] block: unable to load configuration (fstab: Entry not found)
[   15.969762] block: attempting to load /etc/config/fstab
[   16.068189] block: extroot: not configured
[   16.073344] UBIFS (ubi0:1): un-mount UBI device 0
[   16.073421] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[   16.082278] UBIFS (ubi0:1): Mounting in unauthenticated mode
[   16.083311] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 209
[   16.218326] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   16.218376] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   16.225247] UBIFS (ubi0:1): FS size: 84566016 bytes (80 MiB, 666 LEBs), max 677 LEBs, journal size 4190208 bytes (3 MiB, 33 LEBs)
[   16.235154] UBIFS (ubi0:1): reserved for root: 3994261 bytes (3900 KiB)
[   16.246760] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 51812F38-598C-4EC2-899F-926D4787294D, small LPT model
[   16.304839] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   16.305120] block: unable to load configuration (fstab: Entry not found)
[   16.310934] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[   16.317792] block: unable to load configuration (fstab: Entry not found)
[   16.324223] block: attempting to load /etc/config/fstab
[   16.331422] block: extroot: not configured
[   16.339757] mount_root: overlay filesystem has not been fully initialized yet
[   16.341019] mount_root: switching to ubifs overlay
[   19.937632] urandom-seed: Seed file not found (/etc/urandom.seed)
[   20.034287] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
[   20.065889] procd: - early -
[   20.066079] procd: - watchdog -
[   20.067997] procd: Watchdog has previously reset the system
[   20.633654] procd: - watchdog -
[   20.633790] procd: Watchdog has previously reset the system
[   20.636024] procd: - ubus -
[   20.839837] procd: - init -
[   21.902484] urngd: v1.0.2 started.
[   21.930559] kmodloader: loading kernel modules from /etc/modules.d/*
[   22.030261] Key type dns_resolver registered
[   22.050201] Key type cifs.idmap registered
[   22.061011] tun: Universal TUN/TAP device driver, 1.6
[   22.066995] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[   22.076540] gre: GRE over IPv4 demultiplexor driver
[   22.078299] ip_gre: GRE over IPv4 tunneling driver
[   22.147168] GACT probability on
[   22.148583] Mirror/redirect action on
[   22.159458] u32 classifier
[   22.159491]     input device check on
[   22.161059]     Actions configured
[   22.180465] fuse: init (API version 7.34)
[   22.208755] usbcore: registered new interface driver chaoskey
[   22.209786] Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064
[   22.213493] Backport generated by backports.git v5.15.58-1-0-g42a95ce7
[   22.312554] xt_time: kernel timezone is -0000
[   22.476222] PPP generic driver version 2.4.2
[   22.477764] PPP MPPE Compression module registered
[   22.481354] NET: Registered PF_PPPOX protocol family
[   22.485795] PPTP driver version 0.8.5
[   22.495176] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[   22.495237] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <[email protected]>. All Rights Reserved.
[   22.545896] ath10k_pci 0000:01:00.0: assign IRQ: got 43
[   22.545940] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x46.
[   22.547049] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[   22.552961] ath10k_pci 0000:01:00.0: enabling bus mastering
[   22.553459] qcom-pcie 1b500000.pci: msi#1 address_hi 0x0 address_lo 0x4363fe98
[   22.553628] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   23.562390] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[   23.562454] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   23.574632] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5
[   25.902195] ath10k_pci 0000:01:00.0: Loading BDF type 0
[   25.905691] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 826c8c57
[   29.447364] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   29.447418] ath10k_pci 0000:01:00.0: msdu-desc: 2500  skid: 32
[   29.529501] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   29.530351] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[   29.819428] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
[   29.904996] ath: EEPROM regdomain: 0x0
[   29.905014] ath: EEPROM indicates default country code should be used
[   29.905023] ath: doing EEPROM country->regdmn map search
[   29.905035] ath: country maps to regdmn code: 0x3a
[   29.905048] ath: Country alpha2 being used: US
[   29.905057] ath: Regpair used: 0x3a
[   29.908355] ath10k_pci 0001:01:00.0: assign IRQ: got 45
[   29.908392] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x46.
[   29.911146] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[   29.915274] ath10k_pci 0001:01:00.0: enabling bus mastering
[   29.915755] qcom-pcie 1b700000.pci: msi#1 address_hi 0x0 address_lo 0x4378ae98
[   29.915920] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   31.161431] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[   31.161496] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   31.173691] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5
[   33.496562] ath10k_pci 0001:01:00.0: Loading BDF type 0
[   33.497754] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 826c8c57
[   37.059133] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   37.059189] ath10k_pci 0001:01:00.0: msdu-desc: 2500  skid: 32
[   37.143236] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   37.144113] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[   37.440960] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
[   37.524952] ath: EEPROM regdomain: 0x0
[   37.524971] ath: EEPROM indicates default country code should be used
[   37.524981] ath: doing EEPROM country->regdmn map search
[   37.524992] ath: country maps to regdmn code: 0x3a
[   37.525002] ath: Country alpha2 being used: US
[   37.525011] ath: Regpair used: 0x3a
[   37.531633] kmodloader: done loading kernel modules from /etc/modules.d/*
[   54.145165] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[   54.146886] dwmac1000: Master AXI performs any burst length
[   54.152502] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[   54.167665] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[   54.167945] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[   54.175706] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[   54.182766] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[   54.191518] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   54.210687] br-lan: port 1(eth1.1) entered blocking state
[   54.210760] br-lan: port 1(eth1.1) entered disabled state
[   54.215490] device eth1.1 entered promiscuous mode
[   54.220613] device eth1 entered promiscuous mode
[   54.229579] br-lan: port 1(eth1.1) entered blocking state
[   54.229956] br-lan: port 1(eth1.1) entered forwarding state
[   54.255440] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[   54.257022] dwmac1000: Master AXI performs any burst length
[   54.262790] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[   54.277979] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   54.278362] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[   54.330077] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[   54.330660] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   54.338321] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   55.209171] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   56.687642] ath: EEPROM regdomain: 0x80f6
[   56.687668] ath: EEPROM indicates we should expect a country code
[   56.687680] ath: doing EEPROM country->regdmn map search
[   56.687691] ath: country maps to regdmn code: 0x37
[   56.687707] ath: Country alpha2 being used: FI
[   56.687720] ath: Regpair used: 0x37
[   56.687731] ath: regdomain 0x80f6 dynamically updated by user
[   56.687800] ath: EEPROM regdomain: 0x80f6
[   56.687813] ath: EEPROM indicates we should expect a country code
[   56.687824] ath: doing EEPROM country->regdmn map search
[   56.687834] ath: country maps to regdmn code: 0x37
[   56.687847] ath: Country alpha2 being used: FI
[   56.687860] ath: Regpair used: 0x37
[   56.687875] ath: regdomain 0x80f6 dynamically updated by user
[   64.384489] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   64.384546] ath10k_pci 0000:01:00.0: msdu-desc: 2500  skid: 32
[   64.466485] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   64.467324] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[   64.854827] ath10k_pci 0000:01:00.0: rts threshold -1
[   64.855319] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[   64.939167] br-lan: port 2(wlan0) entered blocking state
[   64.939252] br-lan: port 2(wlan0) entered disabled state
[   64.944042] device wlan0 entered promiscuous mode
[   65.174706] ath10k_pci 0000:01:00.0: NOTE:  Firmware DBGLOG output disabled in debug_mask: 0x10000000
[   71.264501] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
[   71.264569] ath10k_pci 0001:01:00.0: msdu-desc: 2500  skid: 32
[   71.348606] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
[   71.349473] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[   71.742468] ath10k_pci 0001:01:00.0: rts threshold -1
[   71.742817] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[   71.762420] br-lan: port 3(wlan1) entered blocking state
[   71.762481] br-lan: port 3(wlan1) entered disabled state
[   71.767265] device wlan1 entered promiscuous mode
[   72.285813] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   72.286147] br-lan: port 3(wlan1) entered blocking state
[   72.291363] br-lan: port 3(wlan1) entered forwarding state
[  136.171468] ath10k_pci 0000:01:00.0: mac flush null vif, drop 0 queues 0xffff
[  136.233488] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  136.233811] br-lan: port 2(wlan0) entered blocking state
[  136.239020] br-lan: port 2(wlan0) entered forwarding state