printrbot 1403 hovis config.ini

config.ini

# generated by Slic3r 1.1.7 on Sun Mar  1 21:30:10 2015
avoid_crossing_perimeters = 0
bed_size = 150,150
bed_temperature = 65
bottom_solid_layers = 2
bridge_acceleration = 5000
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 40
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 5000
disable_fan_first_layers = 1
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = M104 S0 ; turn off temperature\nM140 S65;  keep the bed on\nG28 Y0; home y axis\nM84     ; disable motors\n
external_perimeter_speed = 80%
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 0.973
extrusion_width = 0.4
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 60
fill_density = 7%
fill_pattern = honeycomb
first_layer_acceleration = 5000
first_layer_bed_temperature = 65
first_layer_extrusion_width = 0.4
first_layer_height = 0.2
first_layer_speed = 50%
first_layer_temperature = 185
g0 = 0
gap_fill_speed = 30
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 5000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_gcode = 
layer_height = 0.2
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
min_skirt_length = 0
notes = 
nozzle_diameter = 0.4
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 5000
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 2
post_process = 
print_center = 75,75
raft_layers = 0
resolution = 0
retract_before_travel = 0.5
retract_layer_change = 1
retract_length = 1.5
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
seam_position = aligned
skirt_distance = 4
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 20
small_perimeter_speed = 60
solid_fill_pattern = rectilinear
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G28 X0 Y0 Z0; home all axes\nG29\nG1 Z1
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 1
support_material_interface_speed = 100%
support_material_pattern = honeycomb
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 65
temperature = 180
thin_walls = 1
threads = 5
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 2
travel_speed = 60
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
z_offset = 0.7