config.ini

# generated by Slic3r 1.2.9 on Sat Jun 27 17:23:55 2015
avoid_crossing_perimeters = 0
bed_shape = 109.397x11.4981,107.596x22.8703,104.616x33.9919,100.49x44.741,95.2628x55,88.9919x64.6564,81.7459x73.6044,73.6044x81.7459,64.6564x88.9919,55x95.2628,44.741x100.49,33.9919x104.616,22.8703x107.596,11.4981x109.397,0x110,-11.4981x109.397,-22.8703x107.596,-33.9919x104.616,-44.741x100.49,-55x95.2628,-64.6564x88.9919,-73.6044x81.7459,-81.7459x73.6044,-88.9919x64.6564,-95.2628x55,-100.49x44.741,-104.616x33.9919,-107.596x22.8703,-109.397x11.4981,-110x0,-109.397x-11.4981,-107.596x-22.8703,-104.616x-33.9919,-100.49x-44.741,-95.2628x-55,-88.9919x-64.6564,-81.7459x-73.6044,-73.6044x-81.7459,-64.6564x-88.9919,-55x-95.2628,-44.741x-100.49,-33.9919x-104.616,-22.8703x-107.596,-11.4981x-109.397,0x-110,11.4981x-109.397,22.8703x-107.596,33.9919x-104.616,44.741x-100.49,55x-95.2628,64.6564x-88.9919,73.6044x-81.7459,81.7459x-73.6044,88.9919x-64.6564,95.2628x-55,100.49x-44.741,104.616x-33.9919,107.596x-22.8703,109.397x-11.4981,110x0
bed_temperature = 70
before_layer_gcode = 
bottom_solid_layers = 6
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 28
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 1
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = G28 ; home\nM84 ; disable motors\nM104 S0 ; turn hotend off\nM140 S0 ; turn bed off
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.4
external_perimeter_speed = 120
external_perimeters_first = 1
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0.6
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #989898
filament_diameter = 1.75
fill_angle = 0
fill_density = 10%
fill_pattern = line
first_layer_acceleration = 0
first_layer_bed_temperature = 70
first_layer_extrusion_width = 1
first_layer_height = 0.2
first_layer_speed = 20
first_layer_temperature = 100
gap_fill_speed = 30
gcode_arcs = 0
gcode_comments = 1
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 2
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 120
interface_shells = 0
layer_gcode = 
layer_height = 0.2
max_fan_speed = 100
max_print_speed = 60
max_volumetric_speed = 20
min_fan_speed = 35
min_print_speed = 20
min_skirt_length = 0
notes = 
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 1
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.4
perimeter_speed = 120
perimeters = 6
post_process = 
pressure_advance = 0
raft_layers = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 5
retract_length_toolchange = 10
retract_lift = 1
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 10
small_perimeter_speed = 120
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 120
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G28 ; home
support_material = 1
support_material_angle = 45
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 28
support_material_threshold = 0
temperature = 100
thin_walls = 1
threads = 4
toolchange_gcode = 
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 120
top_solid_layers = 6
travel_speed = 200
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 1
xy_size_compensation = 0
z_offset = 0