ifindev · May 9, 2020 07:29
diff --git a/webserver.ino b/webserver.ino
 /*********
  Original Project by: Rui Santos
  Modified by:  Alvin Samuel
  Complete project details at https://randomnerdtutorials.com
  https://randomnerdtutorials.com/esp32-web-server-arduino-ide/  
 *********/

 // Load Wi-Fi library
 #include <WiFi.h>

 // Replace with your network credentials
 const char* ssid     = "";
 const char* password = "";

 // Set web server port number to 80
 WiFiServer server(80);

 // Variable to store the HTTP request
 String header;

 // Auxiliar variables to store the current output state
 String output26State = "off";
 String output27State = "off";

 // Assign output variables to GPIO pins
 const int output26 = 26;
 const int output27 = 27;

 void setup() {
  Serial.begin(115200);
  // Initialize the output variables as outputs
  pinMode(output26, OUTPUT);
  pinMode(output27, OUTPUT);
  // Set outputs to LOW
  digitalWrite(output26, LOW);
  digitalWrite(output27, LOW);

  // Connect to Wi-Fi network with SSID and password
  Serial.print("Connecting to ");
  Serial.println(ssid);
  WiFi.begin(ssid, password);
  while (WiFi.status() != WL_CONNECTED) {
    delay(500);
    Serial.print(".");
  }
  // Print local IP address and start web server
  Serial.println("");
  Serial.println("WiFi connected.");
  Serial.println("IP address: ");
  Serial.println(WiFi.localIP());
  server.begin();
 }

 void loop(){
  WiFiClient client = server.available();   // Listen for incoming clients

  if (client) {                             // If a new client connects,
    Serial.println("New Client.");          // print a message out in the serial port
    String currentLine = "";                // make a String to hold incoming data from the client
    while (client.connected()) {            // loop while the client's connected
      if (client.available()) {             // if there's bytes to read from the client,
        char c = client.read();             // read a byte, then
        Serial.write(c);                    // print it out the serial monitor
        header += c;
        if (c == '\n') {                    // if the byte is a newline character
          // if the current line is blank, you got two newline characters in a row.
          // that's the end of the client HTTP request, so send a response:
          if (currentLine.length() == 0) {
            // HTTP headers always start with a response code (e.g. HTTP/1.1 200 OK)
            // and a content-type so the client knows what's coming, then a blank line:
            client.println("HTTP/1.1 200 OK");
            client.println("Content-type:text/html");
            client.println("Connection: close");
            client.println();
            
            // turns the GPIOs on and off
            if (header.indexOf("GET /26/on") >= 0) {
              output26State = "on";
            } else if (header.indexOf("GET /26/off") >= 0) {
              output26State = "off";
            } 
            
            // Display the HTML web page
            client.println("<!DOCTYPE html><html>");
            client.println("<head><meta name=\"viewport\" content=\"width=device-width, initial-scale=1\">");
            client.println("<link rel=\"icon\" href=\"data:,\">");
            // CSS to style the on/off buttons 
            // Feel free to change the background-color and font-size attributes to fit your preferences
            client.println("<style>html { font-family: Helvetica; display: inline-block; margin: 0px auto; text-align: center;}");
            client.println(".button { background-color: #4CAF50; border: none; color: white; padding: 16px 40px;");
            client.println("text-decoration: none; font-size: 30px; margin: 2px; cursor: pointer;}");
            client.println(".button2 {background-color: #555555;}</style></head>");
            
            // Web Page Heading
            client.println("<body><h1>ESP32 Web Server</h1>");
            
            int numberOfNetworks = WiFi.scanNetworks();
            for (int i = 0; i < numberOfNetworks; i++) {
              client.println("<p>" + WiFi.SSID(i) + ": " + WiFi.RSSI(i) + "</p>");
            }
            
            // If the output26State is off, it displays the ON button       
            if (output26State=="off") {
              client.println("<p><a href=\"/26/on\"><button class=\"button\">ON</button></a></p>");
            } else {
              client.println("<p><a href=\"/26/off\"><button class=\"button button2\">OFF</button></a></p>");
            } 
               
            client.println("</body></html>");
            
            // The HTTP response ends with another blank line
            client.println();
            // Break out of the while loop
            break;
          } else { // if you got a newline, then clear currentLine
            currentLine = "";
          }
        } else if (c != '\r') {  // if you got anything else but a carriage return character,
          currentLine += c;      // add it to the end of the currentLine
        }
      }
    }
    // Clear the header variable
    header = "";
    // Close the connection
    client.stop();
    Serial.println("Client disconnected.");
    Serial.println("");
  }
 }
	/*********
	Original Project by: Rui Santos
	Modified by: Alvin Samuel
	Complete project details at https://randomnerdtutorials.com
	https://randomnerdtutorials.com/esp32-web-server-arduino-ide/
	*********/

	// Load Wi-Fi library
	#include <WiFi.h>

	// Replace with your network credentials
	const char* ssid = "";
	const char* password = "";

	// Set web server port number to 80
	WiFiServer server(80);

	// Variable to store the HTTP request
	String header;

	// Auxiliar variables to store the current output state
	String output26State = "off";
	String output27State = "off";

	// Assign output variables to GPIO pins
	const int output26 = 26;
	const int output27 = 27;

	void setup() {
	Serial.begin(115200);
	// Initialize the output variables as outputs
	pinMode(output26, OUTPUT);
	pinMode(output27, OUTPUT);
	// Set outputs to LOW
	digitalWrite(output26, LOW);
	digitalWrite(output27, LOW);

	// Connect to Wi-Fi network with SSID and password
	Serial.print("Connecting to ");
	Serial.println(ssid);
	WiFi.begin(ssid, password);
	while (WiFi.status() != WL_CONNECTED) {
	delay(500);
	Serial.print(".");
	}
	// Print local IP address and start web server
	Serial.println("");
	Serial.println("WiFi connected.");
	Serial.println("IP address: ");
	Serial.println(WiFi.localIP());
	server.begin();
	}

	void loop(){
	WiFiClient client = server.available(); // Listen for incoming clients

	if (client) { // If a new client connects,
	Serial.println("New Client."); // print a message out in the serial port
	String currentLine = ""; // make a String to hold incoming data from the client
	while (client.connected()) { // loop while the client's connected
	if (client.available()) { // if there's bytes to read from the client,
	char c = client.read(); // read a byte, then
	Serial.write(c); // print it out the serial monitor
	header += c;
	if (c == '\n') { // if the byte is a newline character
	// if the current line is blank, you got two newline characters in a row.
	// that's the end of the client HTTP request, so send a response:
	if (currentLine.length() == 0) {
	// HTTP headers always start with a response code (e.g. HTTP/1.1 200 OK)
	// and a content-type so the client knows what's coming, then a blank line:
	client.println("HTTP/1.1 200 OK");
	client.println("Content-type:text/html");
	client.println("Connection: close");
	client.println();

	// turns the GPIOs on and off
	if (header.indexOf("GET /26/on") >= 0) {
	output26State = "on";
	} else if (header.indexOf("GET /26/off") >= 0) {
	output26State = "off";
	}

	// Display the HTML web page
	client.println("<!DOCTYPE html><html>");
	client.println("<head><meta name=\"viewport\" content=\"width=device-width, initial-scale=1\">");
	client.println("<link rel=\"icon\" href=\"data:,\">");
	// CSS to style the on/off buttons
	// Feel free to change the background-color and font-size attributes to fit your preferences
	client.println("<style>html { font-family: Helvetica; display: inline-block; margin: 0px auto; text-align: center;}");
	client.println(".button { background-color: #4CAF50; border: none; color: white; padding: 16px 40px;");
	client.println("text-decoration: none; font-size: 30px; margin: 2px; cursor: pointer;}");
	client.println(".button2 {background-color: #555555;}</style></head>");

	// Web Page Heading
	client.println("<body><h1>ESP32 Web Server</h1>");

	int numberOfNetworks = WiFi.scanNetworks();
	for (int i = 0; i < numberOfNetworks; i++) {
	client.println("<p>" + WiFi.SSID(i) + ": " + WiFi.RSSI(i) + "</p>");
	}

	// If the output26State is off, it displays the ON button
	if (output26State=="off") {
	client.println("<p><a href=\"/26/on\"><button class=\"button\">ON</button></a></p>");
	} else {
	client.println("<p><a href=\"/26/off\"><button class=\"button button2\">OFF</button></a></p>");
	}

	client.println("</body></html>");

	// The HTTP response ends with another blank line
	client.println();
	// Break out of the while loop
	break;
	} else { // if you got a newline, then clear currentLine
	currentLine = "";
	}
	} else if (c != '\r') { // if you got anything else but a carriage return character,
	currentLine += c; // add it to the end of the currentLine
	}
	}
	}
	// Clear the header variable
	header = "";
	// Close the connection
	client.stop();
	Serial.println("Client disconnected.");
	Serial.println("");
	}
	}